| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
With previous changes to make the driver handle the TX ring size more
correctly, the default TX ring size of 64 appears to significantly
bottleneck TX performance to around 600 Mbps on a 1 Gbps link on ZynqMP.
Increasing this to 128 seems to bring performance up to near line rate and
shouldn't cause excess bufferbloat (this driver doesn't yet support modern
byte-based queue management).
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Network driver documentation indicates we should be avoiding returning
NETDEV_TX_BUSY from ndo_start_xmit in normal cases, since it requires
the packets to be requeued. Instead the queue should be stopped after
a packet is added to the TX ring when there may not be enough room for an
additional one. Also, when TX ring entries are completed, we should only
wake the queue if we know there is room for another full maximally
fragmented packet.
Print a warning if there is insufficient space at the start of start_xmit,
since this should no longer happen.
Combined with increasing the default TX ring size (in a subsequent
patch), this appears to recover the TX performance lost by previous changes
to actually manage the TX ring state properly.
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The check for the number of available TX ring slots was off by 1 since a
slot is required for the skb header as well as each fragment. This could
result in overwriting a TX ring slot that was still in use.
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The check for whether a TX ring slot was available was incorrect,
since a slot which had been loaded with transmit data but the device had
not started transmitting would be treated as available, potentially
causing non-transmitted slots to be overwritten. The control field in
the descriptor should be checked, rather than the status field (which may
only be updated when the device completes the entry).
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The driver will not work properly if the TX ring size is set to below
MAX_SKB_FRAGS + 1 since it needs to hold at least one full maximally
fragmented packet in the TX ring. Limit setting the ring size to below
this value.
Fixes: 8b09ca823ffb4 ("net: axienet: Make RX/TX ring sizes configurable")
Signed-off-by: Robert Hancock <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This driver was missing some required memory barriers:
Use dma_rmb to ensure we see all updates to the descriptor after we see
that an entry has been completed.
Use wmb and rmb to avoid stale descriptor status between the TX path and
TX complete IRQ path.
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In some cases where the Xilinx Ethernet core was used in 1000Base-X or
SGMII modes, which use the internal PCS/PMA PHY, and the MGT
transceiver clock source for the PCS was not running at the time the
FPGA logic was loaded, the core would come up in a state where the
PCS could not be found on the MDIO bus. To fix this, the Ethernet core
(including the PCS) should be reset after enabling the clocks, prior to
attempting to access the PCS using of_mdio_find_device.
Fixes: 1a02556086fc (net: axienet: Properly handle PCS/PMA PHY for 1000BaseX mode)
Signed-off-by: Robert Hancock <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When resetting the device, wait for the PhyRstCmplt bit to be set
in the interrupt status register before continuing initialization, to
ensure that the core is actually ready. When using an external PHY, this
also ensures we do not start trying to access the PHY while it is still
in reset. The PHY reset is initiated by the core reset which is
triggered just above, but remains asserted for 5ms after the core is
reset according to the documentation.
The MgtRdy bit could also be waited for, but unfortunately when using
7-series devices, the bit does not appear to work as documented (it
seems to behave as some sort of link state indication and not just an
indication the transceiver is ready) so it can't really be relied on for
this purpose.
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The previous timeout of 1ms was too short to handle some cases where the
core is reset just after the input clocks were started, which will
be introduced in an upcoming patch. Increase the timeout to 50ms. Also
simplify the reset timeout checking to use read_poll_timeout.
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Basically nobody should use blake2s in an HMAC construction; it already
has a keyed variant. But unfortunately for historical reasons, Noise,
used by WireGuard, uses HKDF quite strictly, which means we have to use
this. Because this really shouldn't be used by others, this commit moves
it into wireguard's noise.c locally, so that kernels that aren't using
WireGuard don't get this superfluous code baked in. On m68k systems,
this shaves off ~314 bytes.
Cc: Herbert Xu <[email protected]>
Tested-by: Geert Uytterhoeven <[email protected]>
Acked-by: Ard Biesheuvel <[email protected]>
Signed-off-by: Jason A. Donenfeld <[email protected]>
|
|
Pull virtio updates from Michael Tsirkin:
"virtio,vdpa,qemu_fw_cfg: features, cleanups, and fixes.
- partial support for < MAX_ORDER - 1 granularity for virtio-mem
- driver_override for vdpa
- sysfs ABI documentation for vdpa
- multiqueue config support for mlx5 vdpa
- and misc fixes, cleanups"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (42 commits)
vdpa/mlx5: Fix tracking of current number of VQs
vdpa/mlx5: Fix is_index_valid() to refer to features
vdpa: Protect vdpa reset with cf_mutex
vdpa: Avoid taking cf_mutex lock on get status
vdpa/vdpa_sim_net: Report max device capabilities
vdpa: Use BIT_ULL for bit operations
vdpa/vdpa_sim: Configure max supported virtqueues
vdpa/mlx5: Report max device capabilities
vdpa: Support reporting max device capabilities
vdpa/mlx5: Restore cur_num_vqs in case of failure in change_num_qps()
vdpa: Add support for returning device configuration information
vdpa/mlx5: Support configuring max data virtqueue
vdpa/mlx5: Fix config_attr_mask assignment
vdpa: Allow to configure max data virtqueues
vdpa: Read device configuration only if FEATURES_OK
vdpa: Sync calls set/get config/status with cf_mutex
vdpa/mlx5: Distribute RX virtqueues in RQT object
vdpa: Provide interface to read driver features
vdpa: clean up get_config_size ret value handling
virtio_ring: mark ring unused on error
...
|
|
Commit 7cfa9c92d0a3 ("net: sfp: avoid power switch on address-change
modules") unintetionally changed the semantics for high power modules
without the digital diagnostics monitoring. We repeatedly attempt to
read the power status from the non-existing 0xa2 address in a futile
hope this failure is temporary:
[ 8.856051] sfp sfp-eth3: module NTT 0000000000000000 rev 0000 sn 0000000000000000 dc 160408
[ 8.865843] mvpp2 f4000000.ethernet eth3: switched to inband/1000base-x link mode
[ 8.873469] sfp sfp-eth3: Failed to read EEPROM: -5
[ 8.983251] sfp sfp-eth3: Failed to read EEPROM: -5
[ 9.103250] sfp sfp-eth3: Failed to read EEPROM: -5
We previosuly assumed such modules were powered up in the correct mode,
continuing without further configuration as long as the required power
class was supported by the host.
Restore this behaviour, while preserving the intent of subsequent
patches to avoid the "Address Change Sequence not supported" warning
if we are not going to be accessing the DDM address.
Fixes: 7cfa9c92d0a3 ("net: sfp: avoid power switch on address-change modules")
Reported-by: 照山周一郎 <[email protected]>
Tested-by: 照山周一郎 <[email protected]>
Signed-off-by: Russell King (Oracle) <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In the blamed commit, the call to the function
switchdev_bridge_port_offload was passing the wrong argument for
atomic_nb. It was ocelot_netdevice_nb instead of ocelot_swtchdev_nb.
This patch fixes this issue.
Fixes: 4e51bf44a03af6 ("net: bridge: move the switchdev object replay helpers to "push" mode")
Signed-off-by: Horatiu Vultur <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull signal/exit/ptrace updates from Eric Biederman:
"This set of changes deletes some dead code, makes a lot of cleanups
which hopefully make the code easier to follow, and fixes bugs found
along the way.
The end-game which I have not yet reached yet is for fatal signals
that generate coredumps to be short-circuit deliverable from
complete_signal, for force_siginfo_to_task not to require changing
userspace configured signal delivery state, and for the ptrace stops
to always happen in locations where we can guarantee on all
architectures that the all of the registers are saved and available on
the stack.
Removal of profile_task_ext, profile_munmap, and profile_handoff_task
are the big successes for dead code removal this round.
A bunch of small bug fixes are included, as most of the issues
reported were small enough that they would not affect bisection so I
simply added the fixes and did not fold the fixes into the changes
they were fixing.
There was a bug that broke coredumps piped to systemd-coredump. I
dropped the change that caused that bug and replaced it entirely with
something much more restrained. Unfortunately that required some
rebasing.
Some successes after this set of changes: There are few enough calls
to do_exit to audit in a reasonable amount of time. The lifetime of
struct kthread now matches the lifetime of struct task, and the
pointer to struct kthread is no longer stored in set_child_tid. The
flag SIGNAL_GROUP_COREDUMP is removed. The field group_exit_task is
removed. Issues where task->exit_code was examined with
signal->group_exit_code should been examined were fixed.
There are several loosely related changes included because I am
cleaning up and if I don't include them they will probably get lost.
The original postings of these changes can be found at:
https://lkml.kernel.org/r/[email protected]
https://lkml.kernel.org/r/[email protected]
https://lkml.kernel.org/r/[email protected]
I trimmed back the last set of changes to only the obviously correct
once. Simply because there was less time for review than I had hoped"
* 'signal-for-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (44 commits)
ptrace/m68k: Stop open coding ptrace_report_syscall
ptrace: Remove unused regs argument from ptrace_report_syscall
ptrace: Remove second setting of PT_SEIZED in ptrace_attach
taskstats: Cleanup the use of task->exit_code
exit: Use the correct exit_code in /proc/<pid>/stat
exit: Fix the exit_code for wait_task_zombie
exit: Coredumps reach do_group_exit
exit: Remove profile_handoff_task
exit: Remove profile_task_exit & profile_munmap
signal: clean up kernel-doc comments
signal: Remove the helper signal_group_exit
signal: Rename group_exit_task group_exec_task
coredump: Stop setting signal->group_exit_task
signal: Remove SIGNAL_GROUP_COREDUMP
signal: During coredumps set SIGNAL_GROUP_EXIT in zap_process
signal: Make coredump handling explicit in complete_signal
signal: Have prepare_signal detect coredumps using signal->core_state
signal: Have the oom killer detect coredumps using signal->core_state
exit: Move force_uaccess back into do_exit
exit: Guarantee make_task_dead leaks the tsk when calling do_task_exit
...
|
|
Wrong hash sends single stream to multiple output interfaces.
The offset calculation was relative to skb->head, fix it to be relative
to skb->data.
Fixes: a815bde56b15 ("net, bonding: Refactor bond_xmit_hash for use with
xdp_buff")
Reviewed-by: Jussi Maki <[email protected]>
Reviewed-by: Saeed Mahameed <[email protected]>
Reviewed-by: Gal Pressman <[email protected]>
Signed-off-by: Moshe Tal <[email protected]>
Acked-by: Jay Vosburgh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv updates from Wei Liu:
- More patches for Hyper-V isolation VM support (Tianyu Lan)
- Bug fixes and clean-up patches from various people
* tag 'hyperv-next-signed-20220114' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
scsi: storvsc: Fix storvsc_queuecommand() memory leak
x86/hyperv: Properly deal with empty cpumasks in hyperv_flush_tlb_multi()
Drivers: hv: vmbus: Initialize request offers message for Isolation VM
scsi: storvsc: Fix unsigned comparison to zero
swiotlb: Add CONFIG_HAS_IOMEM check around swiotlb_mem_remap()
x86/hyperv: Fix definition of hv_ghcb_pg variable
Drivers: hv: Fix definition of hypercall input & output arg variables
net: netvsc: Add Isolation VM support for netvsc driver
scsi: storvsc: Add Isolation VM support for storvsc driver
hyper-v: Enable swiotlb bounce buffer for Isolation VM
x86/hyper-v: Add hyperv Isolation VM check in the cc_platform_has()
swiotlb: Add swiotlb bounce buffer remap function for HV IVM
|
|
In pci_generic.c there is a 'mru_default' in struct mhi_pci_dev_info.
This value shall be used for whole mhi if it's given a value for a specific product.
But in function mhi_net_rx_refill_work(), it's still using hard code value MHI_DEFAULT_MRU.
'mru_default' shall have higher priority than MHI_DEFAULT_MRU.
And after checking, this change could help fix a data connection lost issue.
Fixes: 5c2c85315948 ("bus: mhi: pci-generic: configurable network interface MRU")
Signed-off-by: Shujun Wang <[email protected]>
Signed-off-by: Slark Xiao <[email protected]>
Reviewed-by: Loic Poulain <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Existing genphy_loopback() is not applicable for Marvell PHY. Besides
configuring bit-6 and bit-13 in Page 0 Register 0 (Copper Control
Register), it is also required to configure same bits in Page 2
Register 21 (MAC Specific Control Register 2) according to speed of
the loopback is operating.
Tested working on Marvell88E1510 PHY for all speeds (1000/100/10Mbps).
FIXME: Based on trial and error test, it seem 1G need to have delay between
soft reset and loopback enablement.
Fixes: 014068dcb5b1 ("net: phy: genphy_loopback: add link speed configuration")
Cc: <[email protected]> # 5.15.x
Signed-off-by: Mohammad Athari Bin Ismail <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
A dma_request_chan() call is hidden in emac_configure_dma().
It must be released in the probe if an error occurs, as already done in
the remove function.
Add the corresponding dma_release_channel() call.
Fixes: 47869e82c8b8 ("sun4i-emac.c: add dma support")
Signed-off-by: Christophe JAILLET <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Clang static analysis reports this problem
mtk_eth_soc.c:394:7: warning: Branch condition evaluates
to a garbage value
if (err)
^~~
err is not initialized and only conditionally set.
So intitialize err.
Fixes: 7e538372694b ("net: ethernet: mediatek: Re-add support SGMII")
Signed-off-by: Tom Rix <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The following command sequence:
tc qdisc del dev swp0 clsact
tc qdisc add dev swp0 ingress_block 1 clsact
tc qdisc add dev swp1 ingress_block 1 clsact
tc filter add block 1 flower action drop
tc qdisc del dev swp0 clsact
produces the following NPD:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000014
pc : vcap_entry_set+0x14/0x70
lr : ocelot_vcap_filter_del+0x198/0x234
Call trace:
vcap_entry_set+0x14/0x70
ocelot_vcap_filter_del+0x198/0x234
ocelot_cls_flower_destroy+0x94/0xe4
felix_cls_flower_del+0x70/0x84
dsa_slave_setup_tc_block_cb+0x13c/0x60c
dsa_slave_setup_tc_block_cb_ig+0x20/0x30
tc_setup_cb_reoffload+0x44/0x120
fl_reoffload+0x280/0x320
tcf_block_playback_offloads+0x6c/0x184
tcf_block_unbind+0x80/0xe0
tcf_block_setup+0x174/0x214
tcf_block_offload_cmd.isra.0+0x100/0x13c
tcf_block_offload_unbind+0x5c/0xa0
__tcf_block_put+0x54/0x174
tcf_block_put_ext+0x5c/0x74
clsact_destroy+0x40/0x60
qdisc_destroy+0x4c/0x150
qdisc_put+0x70/0x90
qdisc_graft+0x3f0/0x4c0
tc_get_qdisc+0x1cc/0x364
rtnetlink_rcv_msg+0x124/0x340
The reason is that the driver isn't prepared to receive two tc filters
with the same cookie. It unconditionally creates a new struct
ocelot_vcap_filter for each tc filter, and it adds all filters with the
same identifier (cookie) to the ocelot_vcap_block.
The problem is here, in ocelot_vcap_filter_del():
/* Gets index of the filter */
index = ocelot_vcap_block_get_filter_index(block, filter);
if (index < 0)
return index;
/* Delete filter */
ocelot_vcap_block_remove_filter(ocelot, block, filter);
/* Move up all the blocks over the deleted filter */
for (i = index; i < block->count; i++) {
struct ocelot_vcap_filter *tmp;
tmp = ocelot_vcap_block_find_filter_by_index(block, i);
vcap_entry_set(ocelot, i, tmp);
}
what will happen is ocelot_vcap_block_get_filter_index() will return the
index (@index) of the first filter found with that cookie. This is _not_
the index of _this_ filter, but the other one with the same cookie,
because ocelot_vcap_filter_equal() gets fooled.
Then later, ocelot_vcap_block_remove_filter() is coded to remove all
filters that are ocelot_vcap_filter_equal() with the passed @filter.
So unexpectedly, both filters get deleted from the list.
Then ocelot_vcap_filter_del() will attempt to move all the other filters
up, again finding them by index (@i). The block count is 2, @index was 0,
so it will attempt to move up filter @i=0 and @i=1. It assigns tmp =
ocelot_vcap_block_find_filter_by_index(block, i), which is now a NULL
pointer because ocelot_vcap_block_remove_filter() has removed more than
one filter.
As far as I can see, this problem has been there since the introduction
of tc offload support, however I cannot test beyond the blamed commit
due to hardware availability. In any case, any fix cannot be backported
that far, due to lots of changes to the code base.
Therefore, let's go for the correct solution, which is to not call
ocelot_vcap_filter_add() and ocelot_vcap_filter_del(), unless the filter
is actually unique and not shared. For the shared filters, we should
just modify the ingress port mask and call ocelot_vcap_filter_replace(),
a function introduced by commit 95706be13b9f ("net: mscc: ocelot: create
a function that replaces an existing VCAP filter"). This way,
block->rules will only contain filters with unique cookies, by design.
Fixes: 07d985eef073 ("net: dsa: felix: Wire up the ocelot cls_flower methods")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
cpumask_first() is a more effective analogue of 'next' version if n == -1
(which means start == 0). This patch replaces 'next' with 'first' where
things look trivial.
There's no cpumask_first_zero() function, so create it.
Signed-off-by: Yury Norov <[email protected]>
Tested-by: Wolfram Sang <[email protected]>
|
|
This will enable cleanups down the road.
The idea is to disable cbs, then add "flush_queued_cbs" callback
as a parameter, this way drivers can flush any work
queued after callbacks have been disabled.
Signed-off-by: Michael S. Tsirkin <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
|
|
If the device is PCI based like intel-eth-pci, pm_runtime_enable() is
already called by pci_pm_init().
So only pm_runtime_enable() when it's not already enabled.
Signed-off-by: Kai-Heng Feng <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
platform_get_irq() returns negative error number instead 0 on failure.
And the doc of platform_get_irq() provides a usage example:
int irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
Fix the check of return value to catch errors correctly.
Fixes: 115978859272 ("i825xx: Move the Intel 82586/82593/82596 based drivers")
Signed-off-by: Miaoqian Lin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Since commit adeef3e32146 ("net: constify netdev->dev_addr") the bmac
driver no longer builds with the following errors (pmac32_defconfig):
linux/drivers/net/ethernet/apple/bmac.c: In function ‘bmac_probe’:
linux/drivers/net/ethernet/apple/bmac.c:1287:20: error: assignment of read-only location ‘*(dev->dev_addr + (sizetype)j)’
1287 | dev->dev_addr[j] = rev ? bitrev8(addr[j]): addr[j];
| ^
Fix it by making the modifications to a local macaddr variable and then
passing that to eth_hw_addr_set().
We don't use the existing addr variable because the bitrev8() would
mutate it, but it is already used unreversed later in the function.
Signed-off-by: Michael Ellerman <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Since commit adeef3e32146 ("net: constify netdev->dev_addr") the mace
driver no longer builds with various errors (pmac32_defconfig):
linux/drivers/net/ethernet/apple/mace.c: In function ‘mace_probe’:
linux/drivers/net/ethernet/apple/mace.c:170:20: error: assignment of read-only location ‘*(dev->dev_addr + (sizetype)j)’
170 | dev->dev_addr[j] = rev ? bitrev8(addr[j]): addr[j];
| ^
linux/drivers/net/ethernet/apple/mace.c: In function ‘mace_reset’:
linux/drivers/net/ethernet/apple/mace.c:349:32: warning: passing argument 2 of ‘__mace_set_address’ discards ‘const’ qualifier from pointer target type
349 | __mace_set_address(dev, dev->dev_addr);
| ~~~^~~~~~~~~~
linux/drivers/net/ethernet/apple/mace.c:93:62: note: expected ‘void *’ but argument is of type ‘const unsigned char *’
93 | static void __mace_set_address(struct net_device *dev, void *addr);
| ~~~~~~^~~~
linux/drivers/net/ethernet/apple/mace.c: In function ‘__mace_set_address’:
linux/drivers/net/ethernet/apple/mace.c:388:36: error: assignment of read-only location ‘*(dev->dev_addr + (sizetype)i)’
388 | out_8(&mb->padr, dev->dev_addr[i] = p[i]);
| ^
Fix it by making the modifications to a local macaddr variable and then
passing that to eth_hw_addr_set(), as well as adding some missing const
qualifiers.
Signed-off-by: Michael Ellerman <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
On boards with LAN9514 and no preconfigured MAC address we don't get an
ip address from DHCP after commit a049a30fc27c ("net: usb: Correct PHY handling
of smsc95xx") anymore. Adding an explicit reset before starting the phy
fixes the issue.
[1]
https://lore.kernel.org/netdev/[email protected]/
From: Gabriel Hojda <[email protected]>
Fixes: a049a30fc27c ("net: usb: Correct PHY handling of smsc95xx")
Signed-off-by: Gabriel Hojda <[email protected]>
Signed-off-by: Markus Reichl <[email protected]>
Tested-by: Alexander Stein <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The driver neglects to check the result of platform_get_irq_optional()'s
call and blithely passes the negative error codes to devm_request_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL.
Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 8562056f267d ("net: bcmgenet: request Wake-on-LAN interrupt")
Signed-off-by: Sergey Shtylyov <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Pull rdma updates from Jason Gunthorpe:
"Another small cycle. Mostly cleanups and bug fixes, quite a bit
assisted from bots. There are a few new syzkaller splats that haven't
been solved yet but they should get into the rcs in a few weeks, I
think.
Summary:
- Update drivers to use common helpers for GUIDs, pkeys, bitmaps,
memset_startat, and others
- General code cleanups from bots
- Simplify some of the rxe pool code in preparation for a larger
rework
- Clean out old stuff from hns, including all support for hip06
devices
- Fix a bug where GID table entries could be missed if the table had
holes in it
- Rename paths and sessions in rtrs for better understandability
- Consolidate the roce source port selection code
- NDR speed support in mlx5"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (83 commits)
RDMA/irdma: Remove the redundant return
RDMA/rxe: Use the standard method to produce udp source port
RDMA/irdma: Make the source udp port vary
RDMA/hns: Replace get_udp_sport with rdma_get_udp_sport
RDMA/core: Calculate UDP source port based on flow label or lqpn/rqpn
IB/qib: Fix typos
RDMA/rtrs-clt: Rename rtrs_clt to rtrs_clt_sess
RDMA/rtrs-srv: Rename rtrs_srv to rtrs_srv_sess
RDMA/rtrs-clt: Rename rtrs_clt_sess to rtrs_clt_path
RDMA/rtrs-srv: Rename rtrs_srv_sess to rtrs_srv_path
RDMA/rtrs: Rename rtrs_sess to rtrs_path
RDMA/hns: Modify the hop num of HIP09 EQ to 1
IB/iser: Align coding style across driver
IB/iser: Remove un-needed casting to/from void pointer
IB/iser: Don't suppress send completions
IB/iser: Rename ib_ret local variable
IB/iser: Fix RNR errors
IB/iser: Remove deprecated pi_guard module param
IB/mlx5: Expose NDR speed through MAD
RDMA/cxgb4: Set queue pair state when being queried
...
|
|
The Hucom Wireless HM-211S/K is an LTE module based on Qualcomm MDM9207.
This module supports LTE Band 1, 3, 5, 7, 8 and WCDMA Band 1.
Manual testing showed that only interface
number two replies to QMI messages.
T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22de ProdID=9051 Rev= 3.18
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=85(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Kyoungkyu Park <[email protected]>
Acked-by: Bjørn Mork <[email protected]>
Link: https://lore.kernel.org/r/Yd+nxAA6KorDpQFv@choryu-tfx5470h
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
To resolve minor conflict in:
drivers/infiniband/hw/mlx5/mlx5_ib.h
By merging both hunks.
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI irq updates from Thomas Gleixner:
"Rework of the MSI interrupt infrastructure.
This is a treewide cleanup and consolidation of MSI interrupt handling
in preparation for further changes in this area which are necessary
to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space"
* tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
genirq/msi: Populate sysfs entry only once
PCI/MSI: Unbreak pci_irq_get_affinity()
genirq/msi: Convert storage to xarray
genirq/msi: Simplify sysfs handling
genirq/msi: Add abuse prevention comment to msi header
genirq/msi: Mop up old interfaces
genirq/msi: Convert to new functions
genirq/msi: Make interrupt allocation less convoluted
platform-msi: Simplify platform device MSI code
platform-msi: Let core code handle MSI descriptors
bus: fsl-mc-msi: Simplify MSI descriptor handling
soc: ti: ti_sci_inta_msi: Remove ti_sci_inta_msi_domain_free_irqs()
soc: ti: ti_sci_inta_msi: Rework MSI descriptor allocation
NTB/msi: Convert to msi_on_each_desc()
PCI: hv: Rework MSI handling
powerpc/mpic_u3msi: Use msi_for_each-desc()
powerpc/fsl_msi: Use msi_for_each_desc()
powerpc/pasemi/msi: Convert to msi_on_each_dec()
powerpc/cell/axon_msi: Convert to msi_on_each_desc()
powerpc/4xx/hsta: Rework MSI handling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core:
- Provide a new interface for affinity hints to provide a separation
between hint and actual affinity change which has become a hidden
property of the current interface
- Fix up the in tree usage of the affinity hint interfaces
Drivers:
- No new irqchip drivers!
- Fix GICv3 redistributor table reservation with RT across kexec
- Fix GICv4.1 redistributor view of the VPE table across kexec
- Add support for extra interrupts on spear-shirq
- Make obtaining some interrupts optional for the Renesas drivers
- Various cleanups and bug fixes"
* tag 'irq-core-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
irqchip/renesas-intc-irqpin: Use platform_get_irq_optional() to get the interrupt
irqchip/renesas-irqc: Use platform_get_irq_optional() to get the interrupt
irqchip/gic-v4: Disable redistributors' view of the VPE table at boot time
irqchip/ingenic-tcu: Use correctly sized arguments for bit field
irqchip/gic-v2m: Add const to of_device_id
irqchip/imx-gpcv2: Mark imx_gpcv2_instance with __ro_after_init
irqchip/spear-shirq: Add support for IRQ 0..6
irqchip/gic-v3-its: Limit memreserve cpuhp state lifetime
irqchip/gic-v3-its: Postpone LPI pending table freeing and memreserve
irqchip/gic-v3-its: Give the percpu rdist struct its own flags field
net/mlx4: Use irq_update_affinity_hint()
net/mlx5: Use irq_set_affinity_and_hint()
hinic: Use irq_set_affinity_and_hint()
scsi: lpfc: Use irq_set_affinity()
mailbox: Use irq_update_affinity_hint()
ixgbe: Use irq_update_affinity_hint()
be2net: Use irq_update_affinity_hint()
enic: Use irq_update_affinity_hint()
RDMA/irdma: Use irq_update_affinity_hint()
scsi: mpt3sas: Use irq_set_affinity_and_hint()
...
|
|
Since commit b39648079db4 ("net: mscc: ocelot: disable flow control on
NPI interface"), flow control should be disabled on the DSA CPU port
when used in NPI mode.
However, the commit blamed in the Fixes: tag below broke this, because
it allowed felix_phylink_mac_link_up() to overwrite SYS_PAUSE_CFG_PAUSE_ENA
for the DSA CPU port.
This issue became noticeable since the device tree update from commit
8fcea7be5736 ("arm64: dts: ls1028a: mark internal links between Felix
and ENETC as capable of flow control").
The solution is to check whether this is the currently configured NPI
port from ocelot_phylink_mac_link_up(), and to not modify the statically
disabled PAUSE frame transmission if it is.
When the port is configured for lossless mode as opposed to tail drop
mode, but the link partner (DSA master) doesn't observe the transmitted
PAUSE frames, the switch termination throughput is much worse, as can be
seen below.
Before:
root@debian:~# iperf3 -c 192.168.100.2
Connecting to host 192.168.100.2, port 5201
[ 5] local 192.168.100.1 port 37504 connected to 192.168.100.2 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 28.4 MBytes 238 Mbits/sec 357 22.6 KBytes
[ 5] 1.00-2.00 sec 33.6 MBytes 282 Mbits/sec 426 19.8 KBytes
[ 5] 2.00-3.00 sec 34.0 MBytes 285 Mbits/sec 343 21.2 KBytes
[ 5] 3.00-4.00 sec 32.9 MBytes 276 Mbits/sec 354 22.6 KBytes
[ 5] 4.00-5.00 sec 32.3 MBytes 271 Mbits/sec 297 18.4 KBytes
^C[ 5] 5.00-5.06 sec 2.05 MBytes 270 Mbits/sec 45 19.8 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-5.06 sec 163 MBytes 271 Mbits/sec 1822 sender
[ 5] 0.00-5.06 sec 0.00 Bytes 0.00 bits/sec receiver
After:
root@debian:~# iperf3 -c 192.168.100.2
Connecting to host 192.168.100.2, port 5201
[ 5] local 192.168.100.1 port 49470 connected to 192.168.100.2 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 112 MBytes 941 Mbits/sec 259 143 KBytes
[ 5] 1.00-2.00 sec 110 MBytes 920 Mbits/sec 329 144 KBytes
[ 5] 2.00-3.00 sec 112 MBytes 936 Mbits/sec 255 144 KBytes
[ 5] 3.00-4.00 sec 110 MBytes 927 Mbits/sec 355 105 KBytes
[ 5] 4.00-5.00 sec 110 MBytes 926 Mbits/sec 350 156 KBytes
[ 5] 5.00-6.00 sec 110 MBytes 925 Mbits/sec 305 148 KBytes
[ 5] 6.00-7.00 sec 110 MBytes 924 Mbits/sec 320 143 KBytes
[ 5] 7.00-8.00 sec 110 MBytes 925 Mbits/sec 273 97.6 KBytes
[ 5] 8.00-9.00 sec 109 MBytes 913 Mbits/sec 299 141 KBytes
[ 5] 9.00-10.00 sec 110 MBytes 922 Mbits/sec 287 146 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 1.08 GBytes 926 Mbits/sec 3032 sender
[ 5] 0.00-10.00 sec 1.08 GBytes 925 Mbits/sec receiver
Fixes: de274be32cb2 ("net: dsa: felix: set TX flow control according to the phylink_mac_link_up resolution")
Reported-by: Xiaoliang Yang <[email protected]>
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Modem from ZTE MF286D is an Qualcomm MDM9250 based 3G/4G modem.
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=5000 MxCh= 0
D: Ver= 3.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=19d2 ProdID=1485 Rev=52.87
S: Manufacturer=ZTE,Incorporated
S: Product=ZTE Technologies MSM
S: SerialNumber=MF286DZTED000000
C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=896mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=ff Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Signed-off-by: Pawel Dembicki <[email protected]>
Acked-by: Bjørn Mork <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty/serial driver updates for 5.17-rc1.
Nothing major in here, just lots of good updates and fixes, including:
- more tty core cleanups from Jiri as well as mxser driver cleanups.
This is the majority of the core diffstat
- tty documentation updates from Jiri
- platform_get_irq() updates
- various serial driver updates for new features and hardware
- fifo usage for 8250 console, reducing cpu load a lot
- LED fix for keyboards, long-time bugfix that went through many
revisions
- minor cleanups
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
serial: core: Keep mctrl register state and cached copy in sync
serial: stm32: correct loop for dma error handling
serial: stm32: fix flow control transfer in DMA mode
serial: stm32: rework TX DMA state condition
serial: stm32: move tx dma terminate DMA to shutdown
serial: pl011: Drop redundant DTR/RTS preservation on close/open
serial: pl011: Drop CR register reset on set_termios
serial: pl010: Drop CR register reset on set_termios
serial: liteuart: fix MODULE_ALIAS
serial: 8250_bcm7271: Fix return error code in case of dma_alloc_coherent() failure
Revert "serdev: BREAK/FRAME/PARITY/OVERRUN notification prototype V2"
tty: goldfish: Use platform_get_irq() to get the interrupt
serdev: BREAK/FRAME/PARITY/OVERRUN notification prototype V2
tty: serial: meson: Drop the legacy compatible strings and clock code
serial: pmac_zilog: Use platform_get_irq() to get the interrupt
serial: bcm63xx: Use platform_get_irq() to get the interrupt
serial: ar933x: Use platform_get_irq() to get the interrupt
serial: vt8500: Use platform_get_irq() to get the interrupt
serial: altera_jtaguart: Use platform_get_irq_optional() to get the interrupt
serial: pxa: Use platform_get_irq() to get the interrupt
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of changes for the driver core for 5.17-rc1.
Lots of little things here, including:
- kobj_type cleanups
- auxiliary_bus documentation updates
- auxiliary_device conversions for some drivers (relevant subsystems
all have provided acks for these)
- kernfs lock contention reduction for some workloads
- other tiny cleanups and changes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (43 commits)
kobject documentation: remove default_attrs information
drivers/firmware: Add missing platform_device_put() in sysfb_create_simplefb
debugfs: lockdown: Allow reading debugfs files that are not world readable
driver core: Make bus notifiers in right order in really_probe()
driver core: Move driver_sysfs_remove() after driver_sysfs_add()
firmware: edd: remove empty default_attrs array
firmware: dmi-sysfs: use default_groups in kobj_type
qemu_fw_cfg: use default_groups in kobj_type
firmware: memmap: use default_groups in kobj_type
sh: sq: use default_groups in kobj_type
headers/uninline: Uninline single-use function: kobject_has_children()
devtmpfs: mount with noexec and nosuid
driver core: Simplify async probe test code by using ktime_ms_delta()
nilfs2: use default_groups in kobj_type
kobject: remove kset from struct kset_uevent_ops callbacks
driver core: make kobj_type constant.
driver core: platform: document registration-failure requirement
vdpa/mlx5: Use auxiliary_device driver data helpers
net/mlx5e: Use auxiliary_device driver data helpers
soundwire: intel: Use auxiliary_device driver data helpers
...
|
|
* Add missed call prestera_router_fini in prestera_switch_fini
* Add prestera_router_hw_fini, which verify lists are empty
Fixes: 69204174cc5c ("net: marvell: prestera: Add prestera router infra")
Signed-off-by: Yevhen Orlov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
* Reverse xmas tree variables order
* User friendly messages on error paths
* Refactor __prestera_inetaddr_event to use early return
Signed-off-by: Yevhen Orlov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
* Use refcount, instead of uint
* Increment/decrement recount inside get/put
* Fix error path in __prestera_vr_create. Remove unnecessary kfree.
* Make __prestera_vr_destroy symmetric to "create"
Fixes: bca5859bc6c6 ("net: marvell: prestera: add hardware router objects accounting")
Signed-off-by: Yevhen Orlov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Field "aborted" was added in
69204174cc5c ("net: marvell: prestera: Add prestera router infra").
It will not be used. So remove.
Signed-off-by: Yevhen Orlov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Add support for OX810SE dwmac glue setup, which is a simplified version
of the OX820 introduced later with more control on the PHY interface.
Signed-off-by: Neil Armstrong <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
In Linux bonding scenario, one packet is copied to several copies and sent
by all slave device of bond0 in mode 3(broadcast mode). The mode 3 xmit
function bond_xmit_broadcast() only ueses the last slave device's tx result
as the final result. In this case, if the last slave device is down, then
it always return NET_XMIT_DROP, even though the other slave devices xmit
success. It may cause the tx statistics error, and cause the application
(e.g. scp) consider the network is unreachable.
For example, use the following command to configure server A.
echo 3 > /sys/class/net/bond0/bonding/mode
ifconfig bond0 up
ifenslave bond0 eth0 eth1
ifconfig bond0 192.168.1.125
ifconfig eth0 up
ifconfig eth1 down
The slave device eth0 and eth1 are connected to server B(192.168.1.107).
Run the ping 192.168.1.107 -c 3 -i 0.2 command, the following information
is displayed.
PING 192.168.1.107 (192.168.1.107) 56(84) bytes of data.
64 bytes from 192.168.1.107: icmp_seq=1 ttl=64 time=0.077 ms
64 bytes from 192.168.1.107: icmp_seq=2 ttl=64 time=0.056 ms
64 bytes from 192.168.1.107: icmp_seq=3 ttl=64 time=0.051 ms
192.168.1.107 ping statistics
0 packets transmitted, 3 received
Actually, the slave device eth0 of the bond successfully sends three
ICMP packets, but the result shows that 0 packets are transmitted.
Also if we use scp command to get remote files, the command end with the
following printings.
ssh_exchange_identification: read: Connection timed out
So this patch modifies the bond_xmit_broadcast to return NET_XMIT_SUCCESS
if one slave device in the bond sends packets successfully. If all slave
devices send packets fail, the discarded packets stats is increased. The
skb is released when there is no slave device in the bond or the last slave
device is down.
Fixes: ae46f184bc1f ("bonding: propagate transmit status")
Signed-off-by: Jie Wang <[email protected]>
Signed-off-by: Guangbin Huang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
We have seen cases where an endpoint RX completion interrupt arrives
while replenishing for the endpoint is underway. This causes another
instance of replenishing to begin as part of completing the receive
transaction. If this occurs it can lead to transaction corruption.
Use a new flag to ensure only one replenish instance for an endpoint
executes at a time.
Fixes: 84f9bd12d46db ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Define a new replenish_flags bitmap to contain Boolean flags
associated with an endpoint's replenishing state. Replace the
replenish_enabled field with a flag in that bitmap. This is to
prepare for the next patch, which adds another flag.
Signed-off-by: Alex Elder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In ipa_endpoint_replenish(), if an error occurs when attempting to
replenish a receive buffer, we just quit and try again later. In
that case we increment the backlog count to reflect that the attempt
was unsuccessful. Then, if the add_one flag was true we increment
the backlog again.
This second increment is not included in the backlog local variable
though, and its value determines whether delayed work should be
scheduled. This is a bug.
Fix this by determining whether 1 or 2 should be added to the
backlog before adding it in a atomic_add_return() call.
Reviewed-by: Matthias Kaehlcke <[email protected]>
Fixes: 84f9bd12d46db ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Don't populate the read-only const array offsets on the stack
but instead make it static. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Mask the ECN bits before calling mlx5e_route_lookup_ipv4_get(). The
tunnel key might have the last ECN bit set. This interferes with the
route lookup process as ip_route_output_key_hash() interpretes this bit
specially (to restrict the route scope).
Found by code inspection, compile tested only.
Fixes: c7b9038d8af6 ("net/mlx5e: TC preparation refactoring for routing update event")
Fixes: 9a941117fb76 ("net/mlx5e: Maximize ip tunnel key usage on the TC offloading path")
Signed-off-by: Guillaume Nault <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Mask the ECN bits before calling ip_route_output_ports(). The tos
variable might be passed directly from an IPv4 header, so it may have
the last ECN bit set. This interferes with the route lookup process as
ip_route_output_key_hash() interpretes this bit specially (to restrict
the route scope).
Found by code inspection, compile tested only.
Fixes: 804c2f3e36ef ("libcxgb,iw_cxgb4,cxgbit: add cxgb_find_route()")
Signed-off-by: Guillaume Nault <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|