| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some small driver core fixes for some oft-reported problems
in 6.0-rc1. They include:
- a bunch of reverts to handle driver_deferred_probe_check_state()
problems that were part of the 6.0-rc1 merge.
- firmware_loader bugfixes now that the code is being properly tested
and used by others
- arch_topology fix
- deferred driver probe bugfix to solve a long-suffering amba bus
problem that many people have reported.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
firmware_loader: Fix memory leak in firmware upload
firmware_loader: Fix use-after-free during unregister
arch_topology: Silence early cacheinfo errors when non-existent
driver core: Don't probe devices after bus_type.match() probe deferral
Revert "iommu/of: Delete usage of driver_deferred_probe_check_state()"
Revert "PM: domains: Delete usage of driver_deferred_probe_check_state()"
Revert "net: mdio: Delete usage of driver_deferred_probe_check_state()"
Revert "driver core: Delete driver_deferred_probe_check_state()"
|
|
This patch adds logic to compute the MDIO period based on
the i1clk, and thereafter write the MDIO period into the YU
MDIO config register. The i1clk resource from the ACPI table
is used to provide addressing to YU bootrecord PLL registers.
The values in these registers are used to compute MDIO period.
If the i1clk resource is not present in the ACPI table, then
the current default hardcorded value of 430Mhz is used.
The i1clk clock value of 430MHz is only accurate for boards
with BF2 mid bin and main bin SoCs. The BF2 high bin SoCs
have i1clk = 500MHz, but can support a slower MDIO period.
Fixes: f92e1869d74e ("Add Mellanox BlueField Gigabit Ethernet driver")
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/20220826155916.12491-1-davthompson@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The function neigh_timer_handler() is a timer handler that runs in an
atomic context. When used by rocker, neigh_timer_handler() calls
"kzalloc(.., GFP_KERNEL)" that may sleep. As a result, the sleep in
atomic context bug will happen. One of the processes is shown below:
ofdpa_fib4_add()
...
neigh_add_timer()
(wait a timer)
neigh_timer_handler()
neigh_release()
neigh_destroy()
rocker_port_neigh_destroy()
rocker_world_port_neigh_destroy()
ofdpa_port_neigh_destroy()
ofdpa_port_ipv4_neigh()
kzalloc(sizeof(.., GFP_KERNEL) //may sleep
This patch changes the gfp_t parameter of kzalloc() from GFP_KERNEL to
GFP_ATOMIC in order to mitigate the bug.
Fixes: 00fc0c51e35b ("rocker: Change world_ops API and implementation to be switchdev independant")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't just print a warning. Clean up and return an error as well.
Fixes: c8349639324a ("net: lan966x: Add FDMA functionality")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/YwjgDm/SVd5c1tQU@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When running `ethtool -p` with the old management firmware,
the management firmware resource is not correctly released,
which causes firmware related malfunction: all the access
to management firmware hangs.
It releases the management firmware resource when set id
mode operation is not supported.
Fixes: ccb9bc1dfa44 ("nfp: add 'ethtool --identify' support")
Signed-off-by: Gao Xiao <gao.xiao@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20220829101651.633840-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan
Stefan Schmidt says:
====================
ieee802154 for net 2022-08-29
- repeated word fix from Jilin Yuan.
- missed return code setting in the cc2520 driver by Li Qiong.
- fixing a potential race in by defering the workqueue destroy
in the adf7242 driver by Lin Ma.
- fixing a long standing problem in the mac802154 rx path to match
corretcly by Miquel Raynal.
* tag 'ieee802154-for-net-2022-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan:
ieee802154: cc2520: add rc code in cc2520_tx()
net: mac802154: Fix a condition in the receive path
net/ieee802154: fix repeated words in comments
ieee802154/adf7242: defer destroy_workqueue call
====================
Link: https://lore.kernel.org/r/20220829100308.2802578-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The same GPIO line can be shared by multiple phys for the coma mode pin.
If that is the case then, all the other phys that share the same line
will failed to be probed because the access to the gpio line is not
non-exclusive.
Fix this by making access to the gpio line to be nonexclusive using flag
GPIOD_FLAGS_BIT_NONEXCLUSIVE. This allows all the other PHYs to be
probed.
Fixes: 738871b09250ee ("net: phy: micrel: add coma mode GPIO")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220830064055.2340403-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On 32bit-UP u64_stats_fetch_begin() disables only preemption. If the
reader is in preemptible context and the writer side
(u64_stats_update_begin*()) runs in an interrupt context (IRQ or
softirq) then the writer can update the stats during the read operation.
This update remains undetected.
Use u64_stats_fetch_begin_irq() to ensure the stats fetch on 32bit-UP
are not interrupted by a writer. 32bit-SMP remains unaffected by this
change.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Catherine Sullivan <csully@google.com>
Cc: David Awogbemila <awogbemila@google.com>
Cc: Dimitris Michailidis <dmichail@fungible.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jeroen de Borst <jeroendb@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Simon Horman <simon.horman@corigine.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: oss-drivers@corigine.com
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xrs700x_read_port_counters() updates the stats from a worker using the
u64_stats_update_begin() version. This is okay on 32-UP since on the
reader side preemption is disabled.
On 32bit-SMP the writer can be preempted by the reader at which point
the reader will spin on the seqcount until writer continues and
completes the update.
Assigning the mib_mutex mutex to the underlying seqcount would ensure
proper synchronisation. The API for that on the u64_stats_init() side
isn't available. Since it is the only user, just use disable interrupts
during the update.
Use u64_stats_update_begin_irqsave() on the writer side to ensure an
uninterrupted update.
Fixes: ee00b24f32eb8 ("net: dsa: add Arrow SpeedChips XRS700x driver")
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rc code is 0 at the error path "status & CC2520_STATUS_TX_UNDERFLOW".
Assign rc code with '-EINVAL' at this error path to fix it.
Signed-off-by: Li Qiong <liqiong@nfschina.com>
Link: https://lore.kernel.org/r/20220829071259.18330-1-liqiong@nfschina.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
The Lenovo OneLink+ Dock contains an RTL8153 controller that behaves as
a broken CDC device by default. Add the custom Lenovo PID to the r8152
driver to support it properly.
Also, systems compatible with this dock provide a BIOS option to enable
MAC address passthrough (as per Lenovo document "ThinkPad Docking
Solutions 2017"). Add the custom PID to the MAC passthrough list too.
Tested on a ThinkPad 13 1st gen with the expected results:
passthrough disabled: Invalid header when reading pass-thru MAC addr
passthrough enabled: Using pass-thru MAC addr XX:XX:XX:XX:XX:XX
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Referenced commit introduced nfp_policer_validate in the progress
installing rate limiter. This validate check the action id and will
reject police with CONTINUE, which is required to support ingress
police offload.
Fix this issue by allowing FLOW_ACTION_CONTINUE as notexceed action
id in nfp_policer_validate
Fixes: d97b4b105ce7 ("flow_offload: reject offload for all drivers with invalid police parameters")
Signed-off-by: Tianyu Yuan <tianyu.yuan@corigine.com>
Reviewed-by: Baowen Zheng <baowen.zheng@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220825080845.507534-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 744d23c71af3 ("net: phy: Warn about incorrect
mdio_bus_phy_resume() state") unveiled that the smsc911x driver was not
properly stopping and restarting the PHY during suspend/resume. Correct
that by indicating that the MAC is in charge of PHY PM operations and
ensure that all MDIO bus activity is quiescent during suspend.
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Fixes: 2aa70f864955 ("net: smsc911x: Quieten netif during suspend")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220825023951.3220-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit d60cd06331a3 ("PM: ACPI: reboot: Use S5 for reboot") caused a
reboot hang on one Dell servers so the commit was reverted.
Someone managed to collect the AER log and it's caused by MSI:
[ 148.762067] ACPI: Preparing to enter system sleep state S5
[ 148.794638] {1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 5
[ 148.803731] {1}[Hardware Error]: event severity: recoverable
[ 148.810191] {1}[Hardware Error]: Error 0, type: fatal
[ 148.816088] {1}[Hardware Error]: section_type: PCIe error
[ 148.822391] {1}[Hardware Error]: port_type: 0, PCIe end point
[ 148.829026] {1}[Hardware Error]: version: 3.0
[ 148.834266] {1}[Hardware Error]: command: 0x0006, status: 0x0010
[ 148.841140] {1}[Hardware Error]: device_id: 0000:04:00.0
[ 148.847309] {1}[Hardware Error]: slot: 0
[ 148.852077] {1}[Hardware Error]: secondary_bus: 0x00
[ 148.857876] {1}[Hardware Error]: vendor_id: 0x14e4, device_id: 0x165f
[ 148.865145] {1}[Hardware Error]: class_code: 020000
[ 148.870845] {1}[Hardware Error]: aer_uncor_status: 0x00100000, aer_uncor_mask: 0x00010000
[ 148.879842] {1}[Hardware Error]: aer_uncor_severity: 0x000ef030
[ 148.886575] {1}[Hardware Error]: TLP Header: 40000001 0000030f 90028090 00000000
[ 148.894823] tg3 0000:04:00.0: AER: aer_status: 0x00100000, aer_mask: 0x00010000
[ 148.902795] tg3 0000:04:00.0: AER: [20] UnsupReq (First)
[ 148.910234] tg3 0000:04:00.0: AER: aer_layer=Transaction Layer, aer_agent=Requester ID
[ 148.918806] tg3 0000:04:00.0: AER: aer_uncor_severity: 0x000ef030
[ 148.925558] tg3 0000:04:00.0: AER: TLP Header: 40000001 0000030f 90028090 00000000
The MSI is probably raised by incoming packets, so power down the device
and disable bus mastering to stop the traffic, as user confirmed this
approach works.
In addition to that, be extra safe and cancel reset task if it's running.
Cc: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/all/b8db79e6857c41dab4ef08bdf826ea7c47e3bafc.1615947283.git.josef@toxicpanda.com/
BugLink: https://bugs.launchpad.net/bugs/1917471
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220826002530.1153296-1-kai.heng.feng@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Packets that are not of length divisible by 4 (e.g. 77, 78, 79) would
have the checksum included up to next multiple of 4 (a 77 bytes packet
would have 3 bytes of ethernet checksum included). The check for the
value expects it in host (Little) endian.
Fixes: f3cad2611a77 ("net: sparx5: add hostmode with phylink support")
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Link: https://lore.kernel.org/r/20220825084955.684637-1-casper.casan@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Daniel borkmann says:
====================
The following pull-request contains BPF updates for your *net* tree.
We've added 11 non-merge commits during the last 14 day(s) which contain
a total of 13 files changed, 61 insertions(+), 24 deletions(-).
The main changes are:
1) Fix BPF verifier's precision tracking around BPF ring buffer, from Kumar Kartikeya Dwivedi.
2) Fix regression in tunnel key infra when passing FLOWI_FLAG_ANYSRC, from Eyal Birger.
3) Fix insufficient permissions for bpf_sys_bpf() helper, from YiFei Zhu.
4) Fix splat from hitting BUG when purging effective cgroup programs, from Pu Lehui.
5) Fix range tracking for array poke descriptors, from Daniel Borkmann.
6) Fix corrupted packets for XDP_SHARED_UMEM in aligned mode, from Magnus Karlsson.
7) Fix NULL pointer splat in BPF sockmap sk_msg_recvmsg(), from Liu Jian.
8) Add READ_ONCE() to bpf_jit_limit when reading from sysctl, from Kuniyuki Iwashima.
9) Add BPF selftest lru_bug check to s390x deny list, from Daniel Müller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from ipsec and netfilter (with one broken Fixes tag).
Current release - new code bugs:
- dsa: don't dereference NULL extack in dsa_slave_changeupper()
- dpaa: fix <1G ethernet on LS1046ARDB
- neigh: don't call kfree_skb() under spin_lock_irqsave()
Previous releases - regressions:
- r8152: fix the RX FIFO settings when suspending
- dsa: microchip: keep compatibility with device tree blobs with no
phy-mode
- Revert "net: macsec: update SCI upon MAC address change."
- Revert "xfrm: update SA curlft.use_time", comply with RFC 2367
Previous releases - always broken:
- netfilter: conntrack: work around exceeded TCP receive window
- ipsec: fix a null pointer dereference of dst->dev on a metadata dst
in xfrm_lookup_with_ifid
- moxa: get rid of asymmetry in DMA mapping/unmapping
- dsa: microchip: make learning configurable and keep it off while
standalone
- ice: xsk: prohibit usage of non-balanced queue id
- rxrpc: fix locking in rxrpc's sendmsg
Misc:
- another chunk of sysctl data race silencing"
* tag 'net-6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
net: lantiq_xrx200: restore buffer if memory allocation failed
net: lantiq_xrx200: fix lock under memory pressure
net: lantiq_xrx200: confirm skb is allocated before using
net: stmmac: work around sporadic tx issue on link-up
ionic: VF initial random MAC address if no assigned mac
ionic: fix up issues with handling EAGAIN on FW cmds
ionic: clear broken state on generation change
rxrpc: Fix locking in rxrpc's sendmsg
net: ethernet: mtk_eth_soc: fix hw hash reporting for MTK_NETSYS_V2
MAINTAINERS: rectify file entry in BONDING DRIVER
i40e: Fix incorrect address type for IPv6 flow rules
ixgbe: stop resetting SYSTIME in ixgbe_ptp_start_cyclecounter
net: Fix a data-race around sysctl_somaxconn.
net: Fix a data-race around netdev_unregister_timeout_secs.
net: Fix a data-race around gro_normal_batch.
net: Fix data-races around sysctl_devconf_inherit_init_net.
net: Fix data-races around sysctl_fb_tunnels_only_for_init_net.
net: Fix a data-race around netdev_budget_usecs.
net: Fix data-races around sysctl_max_skb_frags.
net: Fix a data-race around netdev_budget.
...
|
|
In a situation where memory allocation fails, an invalid buffer address
is stored. When this descriptor is used again, the system panics in the
build_skb() function when accessing memory.
Fixes: 7ea6cd16f159 ("lantiq: net: fix duplicated skb in rx descriptor ring")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the xrx200_hw_receive() function returns -ENOMEM, the NAPI poll
function immediately returns an error.
This is incorrect for two reasons:
* the function terminates without enabling interrupts or scheduling NAPI,
* the error code (-ENOMEM) is returned instead of the number of received
packets.
After the first memory allocation failure occurs, packet reception is
locked due to disabled interrupts from DMA..
Fixes: fe1a56420cf2 ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
xrx200_hw_receive() assumes build_skb() always works and goes straight
to skb_reserve(). However, build_skb() can fail under memory pressure.
Add a check in case build_skb() failed to allocate and return NULL.
Fixes: e015593573b3 ("net: lantiq_xrx200: convert to build_skb")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is a follow-up to the discussion in [0]. It seems to me that
at least the IP version used on Amlogic SoC's sometimes has a problem
if register MAC_CTRL_REG is written whilst the chip is still processing
a previous write. But that's just a guess.
Adding a delay between two writes to this register helps, but we can
also simply omit the offending second write. This patch uses the second
approach and is based on a suggestion from Qi Duan.
Benefit of this approach is that we can save few register writes, also
on not affected chip versions.
[0] https://www.spinics.net/lists/netdev/msg831526.html
Fixes: bfab27a146ed ("stmmac: add the experimental PCI support")
Suggested-by: Qi Duan <qi.duan@amlogic.com>
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/e99857ce-bd90-5093-ca8c-8cd480b5a0a2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-08-24 (ixgbe, i40e)
This series contains updates to ixgbe and i40e drivers.
Jake stops incorrect resetting of SYSTIME registers when starting
cyclecounter for ixgbe.
Sylwester corrects a check on source IP address when validating destination
for i40e.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: Fix incorrect address type for IPv6 flow rules
ixgbe: stop resetting SYSTIME in ixgbe_ptp_start_cyclecounter
====================
Link: https://lore.kernel.org/r/20220824193748.874343-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Assign a random mac address to the VF interface station
address if it boots with a zero mac address in order to match
similar behavior seen in other VF drivers. Handle the errors
where the older firmware does not allow the VF to set its own
station address.
Newer firmware will allow the VF to set the station mac address
if it hasn't already been set administratively through the PF.
Setting it will also be allowed if the VF has trust.
Fixes: fbb39807e9ae ("ionic: support sr-iov operations")
Signed-off-by: R Mohamed Shah <mohamed@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In looping on FW update tests we occasionally see the
FW_ACTIVATE_STATUS command fail while it is in its EAGAIN loop
waiting for the FW activate step to finsh inside the FW. The
firmware is complaining that the done bit is set when a new
dev_cmd is going to be processed.
Doing a clean on the cmd registers and doorbell before exiting
the wait-for-done and cleaning the done bit before the sleep
prevents this from occurring.
Fixes: fbfb8031533c ("ionic: Add hardware init and device commands")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a case found in heavy testing where a link flap happens just
before a firmware Recovery event and the driver gets stuck in the
BROKEN state. This comes from the driver getting interrupted by a FW
generation change when coming back up from the link flap, and the call
to ionic_start_queues() in ionic_link_status_check() fails. This can be
addressed by having the fw_up code clear the BROKEN bit if seen, rather
than waiting for a user to manually force the interface down and then
back up.
Fixes: 9e8eaf8427b6 ("ionic: stop watchdog when in broken state")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Properly report hw rx hash for mt7986 chipset accroding to the new dma
descriptor layout.
Fixes: 197c9e9b17b11 ("net: ethernet: mtk_eth_soc: introduce support for mt7986 chipset")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/091394ea4e705fbb35f828011d98d0ba33808f69.1661257293.git.lorenzo@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It was not possible to create 1-tuple flow director
rule for IPv6 flow type. It was caused by incorrectly
checking for source IP address when validating user provided
destination IP address.
Fix this by changing ip6src to correct ip6dst address
in destination IP address validation for IPv6 flow type.
Fixes: efca91e89b67 ("i40e: Add flow director support for IPv6")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ixgbe_ptp_start_cyclecounter is intended to be called whenever the
cyclecounter parameters need to be changed.
Since commit a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x
devices"), this function has cleared the SYSTIME registers and reset the
TSAUXC DISABLE_SYSTIME bit.
While these need to be cleared during ixgbe_ptp_reset, it is wrong to clear
them during ixgbe_ptp_start_cyclecounter. This function may be called
during both reset and link status change. When link changes, the SYSTIME
counter is still operating normally, but the cyclecounter should be updated
to account for the possibly changed parameters.
Clearing SYSTIME when link changes causes the timecounter to jump because
the cycle counter now reads zero.
Extract the SYSTIME initialization out to a new function and call this
during ixgbe_ptp_reset. This prevents the timecounter adjustment and avoids
an unnecessary reset of the current time.
This also restores the original SYSTIME clearing that occurred during
ixgbe_ptp_reset before the commit above.
Reported-by: Steve Payne <spayne@aurora.tech>
Reported-by: Ilya Evenbach <ievenbach@aurora.tech>
Fixes: a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
On link state change, the controller gets reset,
causing PPS to drop out and the PHC to lose its
time and calibration. So we restart it if needed,
restoring calibration and time registers.
Changes since v2:
* Add `fec_ptp_save_state()`/`fec_ptp_restore_state()`
* Use `ktime_get_real_ns()`
* Use `BIT()` macro
Changes since v1:
* More ECR #define's
* Stop PPS in `fec_ptp_stop()`
Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2022-08-22
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2022-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Unlock on error in mlx5_sriov_enable()
net/mlx5e: Fix use after free in mlx5e_fs_init()
net/mlx5e: kTLS, Use _safe() iterator in mlx5e_tls_priv_tx_list_cleanup()
net/mlx5: unlock on error path in esw_vfs_changed_event_handler()
net/mlx5e: Fix wrong tc flag used when set hw-tc-offload off
net/mlx5e: TC, Add missing policer validation
net/mlx5e: Fix wrong application of the LRO state
net/mlx5: Avoid false positive lockdep warning by adding lock_class_key
net/mlx5: Fix cmd error logging for manage pages cmd
net/mlx5: Disable irq when locking lag_lock
net/mlx5: Eswitch, Fix forwarding decision to uplink
net/mlx5: LAG, fix logic over MLX5_LAG_FLAG_NDEVS_READY
net/mlx5e: Properly disable vlan strip on non-UL reps
====================
Link: https://lore.kernel.org/r/20220822195917.216025-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
ice: xsk: reduced queue count fixes
Maciej Fijalkowski says:
this small series is supposed to fix the issues around AF_XDP usage with
reduced queue count on interface. Due to the XDP rings setup, some
configurations can result in sockets not seeing traffic flowing. More
about this in description of patch 2.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: xsk: use Rx ring's XDP ring when picking NAPI context
ice: xsk: prohibit usage of non-balanced queue id
====================
Link: https://lore.kernel.org/r/20220822163257.2382487-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
LRO/GRO_HW should be disabled if there is an attached XDP program.
BNXT_FLAG_TPA is the current setting of the LRO/GRO_HW. Using
BNXT_FLAG_TPA to disable LRO/GRO_HW will cause these features to be
permanently disabled once they are disabled.
Fixes: 1dc4c557bfed ("bnxt: adding bnxt_xdp_build_skb to build skb from multibuffer xdp_buff")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are 2 issues:
1. We should decrement hw_resc->max_nqs instead of hw_resc->max_irqs
with the number of NQs assigned to the VFs. The IRQs are fixed
on each function and cannot be re-assigned. Only the NQs are being
assigned to the VFs.
2. vf_msix is the total number of NQs to be assigned to the VFs. So
we should decrement vf_msix from hw_resc->max_nqs.
Fixes: b16b68918674 ("bnxt_en: Add SR-IOV support for 57500 chips.")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add missing devlink_set_features() API for callbacks reload_down
and reload_up to function.
Fixes: 228ea8c187d8 ("bnxt_en: implement devlink dev reload driver_reinit")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using BNXT_PAGE_MODE_BUF_SIZE + offset as buffer length value is not
sufficient when running single buffer XDP programs doing redirect
operations. The stack will complain on missing skb tail room. Fix it
by using PAGE_SIZE when calling xdp_init_buff() for single buffer
programs.
Fixes: b231c3f3414c ("bnxt: refactor bnxt_rx_xdp to separate xdp_init_buff/xdp_prepare_buff")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Address learning should initially be turned off by the driver for port
operation in standalone mode, then the DSA core handles changes to it
via ds->ops->port_bridge_flags().
Leaving address learning enabled while ports are standalone breaks any
kind of communication which involves port B receiving what port A has
sent. Notably it breaks the ksz9477 driver used with a (non offloaded,
ports act as if standalone) bonding interface in active-backup mode,
when the ports are connected together through external switches, for
redundancy purposes.
This fixes a major design flaw in the ksz9477 and ksz8795 drivers, which
unconditionally leave address learning enabled even while ports operate
as standalone.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Link: https://lore.kernel.org/netdev/CAFZh4h-JVWt80CrQWkFji7tZJahMfOToUJQgKS5s0_=9zzpvYQ@mail.gmail.com/
Reported-by: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220818164809.3198039-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Looks to have been left out in an oversight.
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Sainath Grandhi <sainath.grandhi@intel.com>
Fixes: 235a9d89da97 ('ipvtap: IP-VLAN based tap driver')
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20220821130808.12143-1-zenczykowski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This reverts commit f8217275b57aa48d98cc42051c2aac34152718d6.
There are a few more issues to fix that have been reported in the thread
for the original series [1]. We'll need to fix those before this will work.
So, revert it for now.
[1] - https://lore.kernel.org/lkml/CAMuHMdWo_wRwV-i_iyTxVnEsf3Th9GBAG+wxUQMQGnw1t2ijTg@mail.gmail.com/
Fixes: f8217275b57a ("net: mdio: Delete usage of driver_deferred_probe_check_state()")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20220819221616.2107893-3-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Delete the redundant word 'was'.
Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Link: https://lore.kernel.org/r/20220708151538.51483-1-yuanjilin@cdjrlc.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
There is a possible race condition (use-after-free) like below
(FREE) | (USE)
adf7242_remove | adf7242_channel
cancel_delayed_work_sync |
destroy_workqueue (1) | adf7242_cmd_rx
| mod_delayed_work (2)
|
The root cause for this race is that the upper layer (ieee802154) is
unaware of this detaching event and the function adf7242_channel can
be called without any checks.
To fix this, we can add a flag write at the beginning of adf7242_remove
and add flag check in adf7242_channel. Or we can just defer the
destructive operation like other commit 3e0588c291d6 ("hamradio: defer
ax25 kfree after unregister_netdev") which let the
ieee802154_unregister_hw() to handle the synchronization. This patch
takes the second option.
Fixes: 58e9683d1475 ("net: ieee802154: adf7242: Fix OCL calibration
runs")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20220808034224.12642-1-linma@zju.edu.cn
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
The value is only ever set once in bond_3ad_initialize and only ever
read otherwise. There seems to be no reason to set the variable via
bond_3ad_initialize when setting the global variable will do. Change
ad_ticks_per_sec to a const to enforce its read-only usage.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is caused by the global variable ad_ticks_per_sec being zero as
demonstrated by the reproducer script discussed below. This causes
all timer values in __ad_timer_to_ticks to be zero, resulting
in the periodic timer to never fire.
To reproduce:
Run the script in
`tools/testing/selftests/drivers/net/bonding/bond-break-lacpdu-tx.sh` which
puts bonding into a state where it never transmits LACPDUs.
line 44: ip link add fbond type bond mode 4 miimon 200 \
xmit_hash_policy 1 ad_actor_sys_prio 65535 lacp_rate fast
setting bond param: ad_actor_sys_prio
given:
params.ad_actor_system = 0
call stack:
bond_option_ad_actor_sys_prio()
-> bond_3ad_update_ad_actor_settings()
-> set ad.system.sys_priority = bond->params.ad_actor_sys_prio
-> ad.system.sys_mac_addr = bond->dev->dev_addr; because
params.ad_actor_system == 0
results:
ad.system.sys_mac_addr = bond->dev->dev_addr
line 48: ip link set fbond address 52:54:00:3B:7C:A6
setting bond MAC addr
call stack:
bond->dev->dev_addr = new_mac
line 52: ip link set fbond type bond ad_actor_sys_prio 65535
setting bond param: ad_actor_sys_prio
given:
params.ad_actor_system = 0
call stack:
bond_option_ad_actor_sys_prio()
-> bond_3ad_update_ad_actor_settings()
-> set ad.system.sys_priority = bond->params.ad_actor_sys_prio
-> ad.system.sys_mac_addr = bond->dev->dev_addr; because
params.ad_actor_system == 0
results:
ad.system.sys_mac_addr = bond->dev->dev_addr
line 60: ip link set veth1-bond down master fbond
given:
params.ad_actor_system = 0
params.mode = BOND_MODE_8023AD
ad.system.sys_mac_addr == bond->dev->dev_addr
call stack:
bond_enslave
-> bond_3ad_initialize(); because first slave
-> if ad.system.sys_mac_addr != bond->dev->dev_addr
return
results:
Nothing is run in bond_3ad_initialize() because dev_addr equals
sys_mac_addr leaving the global ad_ticks_per_sec zero as it is
never initialized anywhere else.
The if check around the contents of bond_3ad_initialize() is no longer
needed due to commit 5ee14e6d336f ("bonding: 3ad: apply ad_actor settings
changes immediately") which sets ad.system.sys_mac_addr if any one of
the bonding parameters whos set function calls
bond_3ad_update_ad_actor_settings(). This is because if
ad.system.sys_mac_addr is zero it will be set to the current bond mac
address, this causes the if check to never be true.
Fixes: 5ee14e6d336f ("bonding: 3ad: apply ad_actor settings changes immediately")
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since priv->rx_mapping[i] is maped in moxart_mac_open(), we
should unmap it from moxart_mac_stop(). Fixes 2 warnings.
1. During error unwinding in moxart_mac_probe(): "goto init_fail;",
then moxart_mac_free_memory() calls dma_unmap_single() with
priv->rx_mapping[i] pointers zeroed.
WARNING: CPU: 0 PID: 1 at kernel/dma/debug.c:963 check_unmap+0x704/0x980
DMA-API: moxart-ethernet 92000000.mac: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=1600 bytes]
CPU: 0 PID: 1 Comm: swapper Not tainted 5.19.0+ #60
Hardware name: Generic DT based system
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x34/0x44
dump_stack_lvl from __warn+0xbc/0x1f0
__warn from warn_slowpath_fmt+0x94/0xc8
warn_slowpath_fmt from check_unmap+0x704/0x980
check_unmap from debug_dma_unmap_page+0x8c/0x9c
debug_dma_unmap_page from moxart_mac_free_memory+0x3c/0xa8
moxart_mac_free_memory from moxart_mac_probe+0x190/0x218
moxart_mac_probe from platform_probe+0x48/0x88
platform_probe from really_probe+0xc0/0x2e4
2. After commands:
ip link set dev eth0 down
ip link set dev eth0 up
WARNING: CPU: 0 PID: 55 at kernel/dma/debug.c:570 add_dma_entry+0x204/0x2ec
DMA-API: moxart-ethernet 92000000.mac: cacheline tracking EEXIST, overlapping mappings aren't supported
CPU: 0 PID: 55 Comm: ip Not tainted 5.19.0+ #57
Hardware name: Generic DT based system
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x34/0x44
dump_stack_lvl from __warn+0xbc/0x1f0
__warn from warn_slowpath_fmt+0x94/0xc8
warn_slowpath_fmt from add_dma_entry+0x204/0x2ec
add_dma_entry from dma_map_page_attrs+0x110/0x328
dma_map_page_attrs from moxart_mac_open+0x134/0x320
moxart_mac_open from __dev_open+0x11c/0x1ec
__dev_open from __dev_change_flags+0x194/0x22c
__dev_change_flags from dev_change_flags+0x14/0x44
dev_change_flags from devinet_ioctl+0x6d4/0x93c
devinet_ioctl from inet_ioctl+0x1ac/0x25c
v1 -> v2:
Extraneous change removed.
Fixes: 6c821bd9edc9 ("net: Add MOXA ART SoCs ethernet driver")
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220819110519.1230877-1-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For some MAC drivers, they set the mac_managed_pm to true in its
->ndo_open() callback. So before the mac_managed_pm is set to true,
we still want to leverage the mdio_bus_phy_suspend()/resume() for
the phy device suspend and resume. In this case, the phy device is
in PHY_READY, and we shouldn't warn about this. It also seems that
the check of mac_managed_pm in WARN_ON is redundant since we already
check this in the entry of mdio_bus_phy_resume(), so drop it.
Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220819082451.1992102-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In ipa_smem_init(), a Qualcomm SMEM region is allocated (if needed)
and then its virtual address is fetched using qcom_smem_get(). The
physical address associated with that region is also fetched.
The physical address is adjusted so that it is page-aligned, and an
attempt is made to update the size of the region to compensate for
any non-zero adjustment.
But that adjustment isn't done properly. The physical address is
aligned twice, and as a result the size is never actually adjusted.
Fix this by *not* aligning the "addr" local variable, and instead
making the "phys" local variable be the adjusted "addr" value.
Fixes: a0036bb413d5b ("net: ipa: define SMEM memory region for IPA")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20220818134206.567618-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
DSA has multiple ways of specifying a MAC connection to an internal PHY.
One requires a DT description like this:
port@0 {
reg = <0>;
phy-handle = <&internal_phy>;
phy-mode = "internal";
};
(which is IMO the recommended approach, as it is the clearest
description)
but it is also possible to leave the specification as just:
port@0 {
reg = <0>;
}
and if the driver implements ds->ops->phy_read and ds->ops->phy_write,
the DSA framework "knows" it should create a ds->slave_mii_bus, and it
should connect to a non-OF-based internal PHY on this MDIO bus, at an
MDIO address equal to the port address.
There is also an intermediary way of describing things:
port@0 {
reg = <0>;
phy-handle = <&internal_phy>;
};
In case 2, DSA calls phylink_connect_phy() and in case 3, it calls
phylink_of_phy_connect(). In both cases, phylink_create() has been
called with a phy_interface_t of PHY_INTERFACE_MODE_NA, and in both
cases, PHY_INTERFACE_MODE_NA is translated into phy->interface.
It is important to note that phy_device_create() initializes
dev->interface = PHY_INTERFACE_MODE_GMII, and so, when we use
phylink_create(PHY_INTERFACE_MODE_NA), no one will override this, and we
will end up with a PHY_INTERFACE_MODE_GMII interface inherited from the
PHY.
All this means that in order to maintain compatibility with device tree
blobs where the phy-mode property is missing, we need to allow the
"gmii" phy-mode and treat it as "internal".
Fixes: 2c709e0bdad4 ("net: dsa: microchip: ksz8795: add phylink support")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216320
Reported-by: Craig McQueen <craig@mcqueen.id.au>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20220818143250.2797111-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Unlock before returning if mlx5_device_enable_sriov() fails.
Fixes: 84a433a40d0e ("net/mlx5: Lock mlx5 devlink reload callbacks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Call mlx5e_fs_vlan_free(fs) before kvfree(fs).
Fixes: af8bbf730068 ("net/mlx5e: Convert mlx5e_flow_steering member of mlx5e_priv to pointer")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Use the list_for_each_entry_safe() macro to prevent dereferencing "obj"
after it has been freed.
Fixes: c4dfe704f53f ("net/mlx5e: kTLS, Recycle objects of device-offloaded TLS TX connections")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Unlock before returning on this error path.
Fixes: f1bc646c9a06 ("net/mlx5: Use devl_ API in mlx5_esw_offloads_devlink_port_register")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|