aboutsummaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2018-10-01net/mlx5e: Avoid unbounded peer devices when unpairing TC hairpin rulesAlaa Hleihel5-3/+69
If the peer device was already unbound, then do not attempt to modify it's resources, otherwise we will crash on dereferencing non-existing device. Fixes: 5c65c564c962 ("net/mlx5e: Support offloading TC NIC hairpin flows") Signed-off-by: Alaa Hleihel <[email protected]> Reviewed-by: Or Gerlitz <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2018-10-01Merge tag 'iwlwifi-next-for-kalle-2018-09-28' of ↵Kalle Valo34-450/+691
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next Second set of iwlwifi patches for 4.20 * TKIP implementation in new devices; * Fix for the shared antenna setting in 22000 series; * Report that we set the RU offset in HE code; * Fix some register addresses in 22000 series; * Fix one FW feature TLV that had a conflict with another value; * A couple of fixes for SoftAP mode; * Work continues for new 22560 hardware; * Some fixes in the datapath; * Some debugging and other general fixes; * Some cleanups, small improvements and other general fixes;
2018-10-01b43: fix spelling mistake "hw_registred" -> "hw_registered"Colin Ian King2-5/+5
Trivial fix to spelling mistake struct field name, rename it. Signed-off-by: Colin Ian King <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01qtnfmac_pcie: check for correct CHIP ID at pcie probeIgor Mitsyanko2-0/+38
Make sure that wifi device is of supported variant by checking it's CHIP ID before completing a probe sequence. Signed-off-by: Igor Mitsyanko <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01qtnfmac: wait for FW load work to finish at PCIe removeIgor Mitsyanko2-4/+1
Waiting for "completion" to be set in FW load thread can not be used in case PCIe remove is called before FW load work was scheduled. Just wait for work completion instead to avoid problems. Signed-off-by: Igor Mitsyanko <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01qtnfmac_pcie: extract platform-independent PCIe codeIgor Mitsyanko5-383/+455
Extract platform-independent PCIe driver code into a separate file, and use it from platform-specific modules. Signed-off-by: Igor Mitsyanko <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01qtnfmac: add missing header includes to bus.hIgor Mitsyanko1-0/+3
A few include directives were missing in bus.h resulting in dependency of include order in other modules. Add missing includes. Signed-off-by: Igor Mitsyanko <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01qtnfmac_pcie: rename platform-specific functionsIgor Mitsyanko1-49/+52
Rename several functions to indicate that they are platform specific. Signed-off-by: Igor Mitsyanko <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01qtnfmac_pcie: separate platform-independent PCIe structureIgor Mitsyanko3-261/+287
Move platform-independent PCIe data structure to a separate header file so it can be reused by different devices. Signed-off-by: Igor Mitsyanko <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01qtnfmac_pcie: pearl: rename spinlock tx0_lock to tx_lockIgor Mitsyanko1-5/+5
tx_lock name will later be reused when common pcie code is extracted to separate files. Signed-off-by: Igor Mitsyanko <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01qtnfmac_pcie: indicate pearl-specific structures by their namesIgor Mitsyanko2-68/+68
In preparation to extract common PCIe driver state, indicate PEARL-specific structures by their name and move them to pearl-specific source file. Signed-off-by: Igor Mitsyanko <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01qtnfmac_pcie: rename private Pearl PCIe state structureIgor Mitsyanko2-138/+111
In preparation to extract common pcie driver state into a separate structure, rename Pearl-specific state to qtnf_pcie_pearl_state and move it directly to pearl-specific PCIe source file. Signed-off-by: Igor Mitsyanko <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01qtnfmac_pcie: move Pearl pcie sources to pcie-specific directoryIgor Mitsyanko5-4/+4
In preparation to extract common qtnfmac PCIe driver sources into a separate file, move existing Pearl-specific pcie driver sources to pcie/ directory. Signed-off-by: Igor Mitsyanko <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01qtnfmac_pcie: do not store FW name in driver state structureIgor Mitsyanko2-5/+4
Firmware name is only needed at probe stage, no point in keeping it in driver state structure. Signed-off-by: Igor Mitsyanko <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01rt2800: flush and txstatus rework for rt2800mmioStanislaw Gruszka4-38/+97
Implement custom rt2800mmio flush routine and change txstatus routine to read TX_STA_FIFO also in the tasklet. Signed-off-by: Stanislaw Gruszka <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01rt2x00: use different txstatus timeouts when flushingStanislaw Gruszka3-10/+26
Use different tx status timeouts for normal operation and when flushing. This increase timeout to 2s for normal operation as when there are bad radio conditions and frames are reposted many times device can not provide the status for quite long. With new timeout we can still get valid status on such bad conditions. Signed-off-by: Stanislaw Gruszka <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01rt2x00: do not check for txstatus timeout every time on taskletStanislaw Gruszka4-1/+12
Do not check for tx status timeout everytime we perform txstatus tasklet. Perform check once per half a second. Signed-off-by: Stanislaw Gruszka <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01rt2800mmio: use txdone/txstatus routines from libStanislaw Gruszka2-172/+9
Use usb txdone/txstatus routines (now in rt2800libc) for mmio devices. Note this also change how we handle INT_SOURCE_CSR_TX_FIFO_STATUS interrupt. Now it is disabled since IRQ routine till end of the txstatus tasklet (the same behaviour like others interrupts). Reason to do not disable this interrupt was not to miss any tx status from 16 entries FIFO register. Now, since we check for tx status timeout, we can allow to miss some tx statuses. However this will be improved in further patch where I also implement read status FIFO register in the tasklet. Signed-off-by: Stanislaw Gruszka <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01rt2800: move usb specific txdone/txstatus routines to rt2800libStanislaw Gruszka3-139/+145
In order to reuse usb txdone/txstatus routines for mmio, move them to common rt2800lib.c file. Signed-off-by: Stanislaw Gruszka <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01rtlwifi: btcoex: Use proper enumerated types for Wi-Fi only interfaceNathan Chancellor1-3/+3
Clang warns when one enumerated type is implicitly converted to another. drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1327:34: warning: implicit conversion from enumeration type 'enum btc_chip_interface' to different enumeration type 'enum wifionly_chip_interface' [-Wenum-conversion] wifionly_cfg->chip_interface = BTC_INTF_PCI; ~ ^~~~~~~~~~~~ drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1330:34: warning: implicit conversion from enumeration type 'enum btc_chip_interface' to different enumeration type 'enum wifionly_chip_interface' [-Wenum-conversion] wifionly_cfg->chip_interface = BTC_INTF_USB; ~ ^~~~~~~~~~~~ drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1333:34: warning: implicit conversion from enumeration type 'enum btc_chip_interface' to different enumeration type 'enum wifionly_chip_interface' [-Wenum-conversion] wifionly_cfg->chip_interface = BTC_INTF_UNKNOWN; ~ ^~~~~~~~~~~~~~~~ 3 warnings generated. Use the values from the correct enumerated type, wifionly_chip_interface. BTC_INTF_UNKNOWN = WIFIONLY_INTF_UNKNOWN = 0 BTC_INTF_PCI = WIFIONLY_INTF_PCI = 1 BTC_INTF_USB = WIFIONLY_INTF_USB = 2 Link: https://github.com/ClangBuiltLinux/linux/issues/135 Signed-off-by: Nathan Chancellor <[email protected]> Acked-by: Ping-Ke Shih <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01ath5k: Remove unused BUG_ONNathan Chancellor1-2/+0
Clang warns that the address of a pointer will always evaluated as true in a boolean context: drivers/net/wireless/ath/ath5k/debug.c:1031:14: warning: address of array 'ah->sbands' will always evaluate to 'true' [-Wpointer-bool-conversion] BUG_ON(!ah->sbands); ~~~~~^~~~~~ ./include/asm-generic/bug.h:61:45: note: expanded from macro 'BUG_ON' #define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0) ^~~~~~~~~ ./include/linux/compiler.h:77:42: note: expanded from macro 'unlikely' # define unlikely(x) __builtin_expect(!!(x), 0) ^ 1 warning generated. Given that this condition is always false because of the logical not, just remove it. Link: https://github.com/ClangBuiltLinux/linux/issues/130 Signed-off-by: Nathan Chancellor <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01rsi: Remove unnecessary boolean conditionNathan Chancellor1-1/+1
Clang warns that the address of a pointer will always evaluated as true in a boolean context. drivers/net/wireless/rsi/rsi_91x_mac80211.c:927:50: warning: address of array 'key->key' will always evaluate to 'true' [-Wpointer-bool-conversion] if (vif->type == NL80211_IFTYPE_STATION && key->key && ~~ ~~~~~^~~ 1 warning generated. Link: https://github.com/ClangBuiltLinux/linux/issues/136 Signed-off-by: Nathan Chancellor <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01ipw2x00: Remove unnecessary parenthesesNathan Chancellor1-1/+1
Clang warns when multiple pairs of parentheses are used for a single conditional statement. drivers/net/wireless/intel/ipw2x00/ipw2200.c:5655:28: warning: equality comparison with extraneous parentheses [-Wparentheses-equality] if ((priv->ieee->iw_mode == IW_MODE_ADHOC)) { ~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~ drivers/net/wireless/intel/ipw2x00/ipw2200.c:5655:28: note: remove extraneous parentheses around the comparison to silence this warning if ((priv->ieee->iw_mode == IW_MODE_ADHOC)) { ~ ^ ~ drivers/net/wireless/intel/ipw2x00/ipw2200.c:5655:28: note: use '=' to turn this equality comparison into an assignment if ((priv->ieee->iw_mode == IW_MODE_ADHOC)) { ^~ = 1 warning generated. Link: https://github.com/ClangBuiltLinux/linux/issues/134 Signed-off-by: Nathan Chancellor <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01wil6210: remove set but not used variable 'start'YueHaibing1-2/+1
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/ath/wil6210/pm.c: In function 'wil_suspend_keep_radio_on': drivers/net/wireless/ath/wil6210/pm.c:193:16: warning: variable 'start' set but not used [-Wunused-but-set-variable] Signed-off-by: YueHaibing <[email protected]> Reviewed-by: Maya Erez <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01ath9k: debug: remove set but not used variable 'fops_dump_nfcal'YueHaibing1-13/+0
'fops_dump_nfcal' is not used since commit 4447d815fd0f ("ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries") Signed-off-by: YueHaibing <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01ath9k: add reset for airtime station debugfsLouie Lu1-1/+17
Let user can reset station airtime status by debugfs, it will reset all airtime deficit to ATH_AIRTIME_QUANTUM and reset rx/tx airtime accumulate to 0. Signed-off-by: Louie Lu <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01ath10k: disable napi before resource cleanup to avoid "use after free"Govind Singh1-1/+1
CE buffers are cleaned up prior to napi disable and this is causing NULL pointer dereference due to "use after free". Disable napi before resource cleanup to avoid "use after free". Signed-off-by: Govind Singh <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01ath10k: move napi_enable to hif_start for consistent pairingGovind Singh1-1/+1
There is unbalanced napi_{enable,disable}() behavior as they are being called from hif_snoc_{power_up/stop). The fix is to call napi_enable() from ath10k_snoc_hif_start() so that it matches with napi_disable() being called from ath10k_snoc_hif_stop(). Signed-off-by: Govind Singh <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01ath10k: advertize beacon_int_min_gcd as 100 while bring up multi vapsMaharaja Kennadyrajan2-0/+34
With the latest firmware design, the beacon interval should be greater than 100 to bring the multiple vaps. Set beacon_int_min_gcd to 100, when the wmi service WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT is enabled in the firmware. If not, beacon_int_min_gcd will be set to the default value 1. Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00015 Tested in QCA9888 with firmware ver 10.4-3.5.1-0005 Signed-off-by: Maharaja Kennadyrajan <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01ath10k: add debugfs support to get power save state change of STAMaharaja Kennadyrajan6-1/+161
This patch helps to get the power save state change of each peer connected to the AP. With WMI_10_4_PEER_STA_PS_STATECHG_EVENTID event, ps state of each peer is reported to user space via debugfs. Use the below command to get the ps state of each sta: cat /sys/kernel/debug/ieee80211/phyX/netdev::wlanX/stations/ XX:XX:XX:XX:XX:XX/peer_ps_state If STA is in power save state, we get the peer_ps_state value as 1. if STA is not in power save state, we get the peer_ps_state value as 0. If ps_state event is disabled, we get the peer_ps_state value as 2. We can enable/disable the ps_state events using the debugfs flag "ps_state_enable" echo Y > /sys/kernel/debug/ieee80211/phyX/ath10k/ps_state_enable Y = 1 to enable and Y = 0 to disable Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011 Signed-off-by: Maharaja Kennadyrajan <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01ath10k: remove duplicated includesYueHaibing3-3/+0
remove duplicated include from ath10k driver. Signed-off-by: YueHaibing <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01ath10k: add support for configuring management packet rateSriram R1-2/+43
By default the firmware uses 1Mbps and 6Mbps rate for management packets in 2G and 5G bands respectively. But when the user selects different basic rates from the userspace, we need to send the management packets at the lowest basic rate selected by the user. This change makes use of WMI_VDEV_PARAM_MGMT_RATE param for configuring the management packets rate to the firmware. Chipsets Tested : QCA988X, QCA9887, QCA9984 FW Tested : 10.2.4-1.0-41, 10.4-3.6.104 Signed-off-by: Sriram R <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01ath10k: remove num_peers in hw_params for most targetsErik Stromdahl1-13/+0
>From commit "ath10k: add per target config of max_num_peers", the num_peers value in struct ath10k_hw_params is used to override the value obtained from the WMI op version in the firmware file. Currently, only high latency devices (USB and SDIO) need to use this value, since the value obtained from the WMI op version is not applicable for these devices. Many devices in ath10k_hw_params_list have the wrong value set. An example of this is the QCA9880 hw2.0 chipset that had (before this patch) num_peers set to TARGET_TLV_NUM_PEERS although the firmware uses WMI version ATH10K_FW_WMI_OP_VERSION_10_2_4. Using the wrong value for the QCA9880 chip results in a fw crash: ath10k_pci 0000:01:00.0: firmware crashed! (guid ddf39880-3e64-4edf-b4e4-979d31724503) ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000 ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 0 ath10k_pci 0000:01:00.0: firmware ver 10.2.4-1.0-00037 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 a4a52adb ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08 ath10k_pci 0000:01:00.0: htt-ver 0.0 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 ath10k_pci 0000:01:00.0: firmware register dump: ath10k_pci 0000:01:00.0: [00]: 0x4100016C 0x000015B3 0x009B54B7 0x00955B31 ath10k_pci 0000:01:00.0: [04]: 0x009B54B7 0x00060530 0x00000011 0x00400000 ath10k_pci 0000:01:00.0: [08]: 0x000001B8 0x00000007 0x00443138 0x00955A00 ath10k_pci 0000:01:00.0: [12]: 0x00000009 0x00000000 0x009B548E 0x009B54AB ath10k_pci 0000:01:00.0: [16]: 0x00958080 0x0094078E 0x00000000 0x00000000 ath10k_pci 0000:01:00.0: [20]: 0x409B54B7 0x0040AC64 0x00400000 0x00000087 ath10k_pci 0000:01:00.0: [24]: 0x809A3831 0x0040ACC4 0x000001B1 0xC09B54B7 ath10k_pci 0000:01:00.0: [28]: 0x809A2F08 0x0040AD04 0x00410410 0x00000001 ath10k_pci 0000:01:00.0: [32]: 0x80988856 0x0040AD24 0x00410410 0x00000001 ath10k_pci 0000:01:00.0: [36]: 0x8098AF64 0x0040AD44 0x00410410 0x00000001 ath10k_pci 0000:01:00.0: [40]: 0x809B5DEC 0x0040AD84 0x00410410 0x00410FF4 ath10k_pci 0000:01:00.0: [44]: 0x809B1F20 0x0040ADA4 0x00400000 0x00416C54 ath10k_pci 0000:01:00.0: [48]: 0x809C0295 0x0040ADE4 0x0040AE08 0x00411DC8 ath10k_pci 0000:01:00.0: [52]: 0x809486FA 0x0040AE04 0x00000001 0x00000000 ath10k_pci 0000:01:00.0: [56]: 0x80948E2C 0x0040AEA4 0x0041F290 0x004123D4 ath10k_pci 0000:01:00.0: Copy Engine register dump: ath10k_pci 0000:01:00.0: [00]: 0x00057400 10 10 3 3 ath10k_pci 0000:01:00.0: [01]: 0x00057800 3 3 8 9 ath10k_pci 0000:01:00.0: [02]: 0x00057c00 2 2 1 2 ath10k_pci 0000:01:00.0: [03]: 0x00058000 1 1 2 1 ath10k_pci 0000:01:00.0: [04]: 0x00058400 0 0 40 0 ath10k_pci 0000:01:00.0: [05]: 0x00058800 1 1 0 1 ath10k_pci 0000:01:00.0: [06]: 0x00058c00 0 0 0 0 ath10k_pci 0000:01:00.0: [07]: 0x00059000 0 0 0 0 Signed-off-by: Erik Stromdahl <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01ath10k: add default value for num_peers in WMI TLV initErik Stromdahl1-1/+4
The hw_params value will only be used if it was explicitly set in the global hw_params array. This makes it possible to have the num_peers member unset. Signed-off-by: Erik Stromdahl <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01ath10k: utilize random MAC address if none is providedBrian Norris1-0/+4
Since commit 9d5804662ce1 ("ath10k: retrieve MAC address from system firmware if provided"), we support pulling our MAC address from system firmware. Along with this, we should admit that it's possible for system firmware to be screwed up as well, omitting the MAC address there. Provide a fallback, such that we choose a randomly-generated MAC address, with the local assignment bit set. This is not a preferred mode of operation and really should only serve the purpose of keeping the system chugging along while someone figures out what's wrong with the system. Grepping through other wireless drivers shows very similar fallback logic though, so why not? git grep eth_random_addr drivers/net/wireless/ Signed-off-by: Brian Norris <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01ath10k: fix tx status flag setting for management framesRakesh Pillai1-1/+6
The tx_status for management frames is being filled incorrectly in the flags of skb_cb. This incorrect flag setting causes the upper layers to consider that the particular frame was not transmitted properly, leading to improper behavior. Set the IEEE80211_TX_STAT_ACK flag in the info flags of skb_cb, to indicate the successful transmission of the management frame. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1 Fixes: dc405152bb64d4ae01c9ac669de25b2d1fb6fc2d Signed-off-by: Rakesh Pillai <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01ath10k: fix vdev-start timeout on errorBen Greear4-5/+25
The vdev-start-response message should cause the completion to fire, even in the error case. Otherwise, the user still gets no useful information and everything is blocked until the timeout period. Add some warning text to print out the invalid status code to aid debugging, and propagate failure code. Signed-off-by: Ben Greear <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
2018-10-01mt76: mt76x2: fix multi-interface beacon configurationFelix Fietkau1-2/+1
If the first virtual interface is a station (or an AP with beacons temporarily disabled), the beacon of the second interface needs to occupy hardware beacon slot 0. For some reason the beacon index was incorrectly masked with the virtual interface beacon mask, which prevents the secondary interface from sending beacons unless the first one also does. Cc: [email protected] Signed-off-by: Felix Fietkau <[email protected]>
2018-10-01mt76: check aggregation sequence number for frames sent via drv_txFelix Fietkau1-11/+25
ps-poll response frames can be sent via drv_tx. Store the frame sequence number for such frames, in case a BlockAckReq needs to be sent Signed-off-by: Felix Fietkau <[email protected]>
2018-10-01mt76: fix handling ps-poll framesFelix Fietkau1-0/+6
Hardware station lookup for pspoll frames can fail, which makes the driver ignore ps-poll frames. Fix the resulting powersave issues by looking up the station for pspoll frames in software Signed-off-by: Felix Fietkau <[email protected]>
2018-10-01mt76x0: usb: move mt76x0u_tx_prepare_skb in usb.cLorenzo Bianconi3-24/+24
Move mt76x0u_tx_prepare_skb routine in usb module in order to remove leftover usb dependency from generic code Signed-off-by: Lorenzo Bianconi <[email protected]> Signed-off-by: Felix Fietkau <[email protected]>
2018-10-01mt76x0: eeprom: load eeprom data from mtd by defaultLorenzo Bianconi1-13/+43
Read eeprom data from mtd memory by default and fall-back to efuse if it fails Signed-off-by: Lorenzo Bianconi <[email protected]> Signed-off-by: Felix Fietkau <[email protected]>
2018-10-01mt76x0: pci: add mt76x0e_{start/stop} callbacksLorenzo Bianconi1-0/+34
Introduce mt76x0e_start and mt76x0e_stop mac80211 callbacks to start/stop device mac opening/closing the netdevice Signed-off-by: Lorenzo Bianconi <[email protected]> Signed-off-by: Felix Fietkau <[email protected]>
2018-10-01mt76x0: add ieee80211_ops ops pointer to mt76x0_alloc_device signatureLorenzo Bianconi6-103/+135
Add ieee80211_ops ops pointer to mt76x0_alloc_device routine signature in order to specify mac80211 callbacks and remove usb dependency from mt76x0 generic code. Move mt76x0_ops callbacks in usb module in order to remove leftover usb dependency in mt76x0 generic code. Introduce mt76x0e_ops mac80211 callbacks for pci code Signed-off-by: Lorenzo Bianconi <[email protected]> Signed-off-by: Felix Fietkau <[email protected]>
2018-10-01mt76: move set_{tx,rx}_path routines in mt76x02-lib moduleLorenzo Bianconi13-73/+50
Move mt76x02_phy_set_rxpath and mt76x02_phy_tx_dac routines in mt76x02_phy.c since they are shared between mt76x2 and mt76x0 drivers. Moreover move chainmask variable from mt76x2/mt76x0 to mt76_dev data structure Signed-off-by: Lorenzo Bianconi <[email protected]> Signed-off-by: Felix Fietkau <[email protected]>
2018-10-01mt76x0: phy: set antenna parameter according to wireless bandLorenzo Bianconi1-11/+20
Move mt76x0_ant_select routine in __mt76x0_phy_set_channel in order to configure antenna parameters according to the current wireless channel Signed-off-by: Lorenzo Bianconi <[email protected]> Signed-off-by: Felix Fietkau <[email protected]>
2018-10-01mt76x0: pci: add hw initialization at bootstrapLorenzo Bianconi3-8/+50
Add mt76x0e_register_device routine in pci.c to initialize the device during hw probe. Signed-off-by: Lorenzo Bianconi <[email protected]> Signed-off-by: Felix Fietkau <[email protected]>
2018-10-01mt76x0: usb: move initialization code in usb.cLorenzo Bianconi3-79/+91
Move usb initialization code in mt76x0-usb module in order to remove usb dependency from generic init code (not completed yet). Moreover fix a memory leak in usb probe if mt76x02_wait_for_mac fails Signed-off-by: Lorenzo Bianconi <[email protected]> Signed-off-by: Felix Fietkau <[email protected]>
2018-10-01mt76: add mt76x02_mac_start routineLorenzo Bianconi3-11/+15
Introduce mt76x02_mac_start since the mac start code is shared between mt76x0e and mt76x2 drivers. Signed-off-by: Lorenzo Bianconi <[email protected]> Signed-off-by: Felix Fietkau <[email protected]>
2018-10-01mt76x0: init rx filter in mt76x0_init_hardwareLorenzo Bianconi2-8/+11
Initialize rxfilter mask at bootstrap an not at mac start. This is a preliminary patch to share mt76x2_mac_start routine between mt76x2e and mt76x0e drivers Signed-off-by: Lorenzo Bianconi <[email protected]> Signed-off-by: Felix Fietkau <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.