| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
A hardware/firmware error may happen at any point in time. In
particular, it might happen while mac80211 is in the middle of
a flow. We observed the following situation:
* mac80211 is in authentication flow, in ieee80211_prep_connection()
* iwlwifi firmware crashes, but no error can be reported at this
precise point (mostly because the driver method is void, but even
if it wasn't we'd just shift to a race condition)
* mac80211 continues the flow, trying to add the AP station
* iwlwifi has already set its internal restart flag, and so thinks
that adding the station is part of the restart and already set up,
so it uses the information that's supposed to already be in the
struct
This can happen with any flow in mac80211 and with any information
we try to preserve across hardware restarts.
To fix this, only set a new HW_RESTART_REQUESTED flag and translate
that to IN_HW_RESTART once mac80211 actually starts the restart by
calling our start() method. As a consequence, any mac80211 flow in
progress at the time of the restart will properly finish (certainly
with errors), before the restart is attempted.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195299.
Reported-by: djagoo <[email protected]>
Reported-by: Łukasz Siudut <[email protected]>
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
When IBSS was implemented for DQA, we missid a few places where it
should be handled in the same way as AP.
Fixes: ee48b72211f8 ("iwlwifi: mvm: support ibss in dqa mode")
Signed-off-by: Luca Coelho <[email protected]>
|
|
iwl_trace_data is somewhat confusing. It returns a bool
that tells if the payload of the skb should be added to
the tx_data event. If it returns false, then the payload
of the skb is added to the tx event.
The purpose is to be able to start tracing with
-e iwlwifi
and record non-data packets only which saves bandwidth.
Since EAPOLs are important, seldom and not real data
packet (despite being WiFi data packets), they are
included in tx event and thus iwl_trace_data returns false
on those. This last part was buggy, and because of that,
all the data packets were included in the tx event.
Fix that.
Fixes: 0c4cb7314d15 ("iwlwifi: tracing: decouple from mac80211")
Signed-off-by: Emmanuel Grumbach <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
We don't set the error code here so we end up returning ERR_PTR(0) which
is NULL. The caller doesn't expect that so it results in a NULL
dereference.
Fixes: 2e5d4a8f61dc ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
Sometimes, we can have an firmware crash while trying to
recover from a previous firmware problem.
When that happens, lots of things can go wrong. For example
the stations don't get added properly to mvm->fw_id_to_mac_id.
Mac80211 tries to stop A-MPDU upon reconfig but in case of
a firmware crash we will bail out fairly early and in the
end, we won't delete the A-MPDU Rx timeout.
When that timer expired after a double firmware crash,
we end up dereferencing mvm->fw_id_to_mac_id[sta_id]
which is NULL.
Fixes: 10b2b2019d81 ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Emmanuel Grumbach <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
Before TVQM, all TX queues were allocated straight at init.
With TVQM, queues are allocated on demand and hence we need
to check if a queue exists before dereferencing it.
Fixes: 66128fa08806 ("iwlwifi: move to TVQM mode")
Signed-off-by: Mordechai Goodstein <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
iwlagn_check_ratid_empty takes the tid as a parameter, but
it doesn't check that it is not IWL_TID_NON_QOS.
Since IWL_TID_NON_QOS = 8 and iwl_priv::tid_data is an array
with 8 entries, accessing iwl_priv::tid_data[IWL_TID_NON_QOS]
is a bad idea.
This happened in iwlagn_rx_reply_tx. Since
iwlagn_check_ratid_empty is relevant only to check whether
we can open A-MPDU, this flow is irrelevant if tid is
IWL_TID_NON_QOS. Call iwlagn_check_ratid_empty only inside
the
if (tid != IWL_TID_NON_QOS)
a few lines earlier in the function.
Cc: <[email protected]>
Reported-by: Seraphime Kirkovski <[email protected]>
Tested-by: Seraphime Kirkovski <[email protected]>
Signed-off-by: Emmanuel Grumbach <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
This reverts commit f95d95a7cd5514549dcf6ba754f0ee834cce3e1f.
With commit f95d95a7cd55 ("rtlwifi: btcoex: rtl8723be: fix ant_sel not
work"), the kernel has a NULL pointer dereference oops. This content and
the proper fix will be included in a later patch.
Fixes: f95d95a7cd55 ("rtlwifi: btcoex: rtl8723be: fix ant_sel not work")
Signed-off-by: Larry Finger <[email protected]>
Cc: Ping-Ke Shih <[email protected]>
Cc: Yan-Hsuan Chuang <[email protected]>
Cc: Birming Chiu <[email protected]>
Cc: Shaofu <[email protected]>
Cc: Steven Ting <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Recent change in brcmf_sdio_txpkt_hdalign() changed the
behavior and now always returns 0. This resulted in a
regression which basically renders the device useless.
Fixes: 270a6c1f65fe ("brcmfmac: rework headroom check in .start_xmit()")
Reported-by: S. Gilles <[email protected]>
Tested-by: S. Gilles <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
|
|
Remove useless local variables last_read_point and last_txw_point and
the code related.
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Acked-by: Larry Finger <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Remove unnecessary static on local function pointer _writer_.
Such pointer is initialized before being used, on every
execution path throughout the function. The static has no
benefit and, removing it reduces the object file size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see a significant difference in the object
file size. This log is the output of the size command, before and after
the code change:
before:
text data bss dec hex filename
113797 19152 1216 134165 20c15 drivers/net/wireless/cisco/airo.o
after:
text data bss dec hex filename
113881 19096 1152 134129 20bf1 drivers/net/wireless/cisco/airo.o
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Don't populate array glrt_table on the stack but make it static.
Makes the object code a smaller by over 670 bytes:
Before:
text data bss dec hex filename
131772 4733 0 136505 21539 rt2800lib.o
After:
text data bss dec hex filename
131043 4789 0 135832 21298 rt2800lib.o
Signed-off-by: Colin Ian King <[email protected]>
Acked-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The lower level nl80211 code in cfg80211 ensures that "len" is between
25 and NL80211_ATTR_FRAME (2304). We subtract DOT11_MGMT_HDR_LEN (24) from
"len" so thats's max of 2280. However, the action_frame->data[] buffer is
only BRCMF_FIL_ACTION_FRAME_SIZE (1800) bytes long so this memcpy() can
overflow.
memcpy(action_frame->data, &buf[DOT11_MGMT_HDR_LEN],
le16_to_cpu(action_frame->len));
Cc: [email protected] # 3.9.x
Fixes: 18e2f61db3b70 ("brcmfmac: P2P action frame tx.")
Reported-by: "freenerguo(郭大兴)" <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add sysfs max_link_speed/width, current_link_speed/width (Wong Vee
Khee)
- make host bridge IRQ mapping much more generic (Matthew Minter,
Lorenzo Pieralisi)
- convert most drivers to pci_scan_root_bus_bridge() (Lorenzo
Pieralisi)
- mutex sriov_configure() (Jakub Kicinski)
- mutex pci_error_handlers callbacks (Christoph Hellwig)
- split ->reset_notify() into ->reset_prepare()/reset_done()
(Christoph Hellwig)
- support multiple PCIe portdrv interrupts for MSI as well as MSI-X
(Gabriele Paoloni)
- allocate MSI/MSI-X vector for Downstream Port Containment (Gabriele
Paoloni)
- fix MSI IRQ affinity pre/post/min_vecs issue (Michael Hernandez)
- test INTx masking during enumeration, not at run-time (Piotr Gregor)
- avoid using device_may_wakeup() for runtime PM (Rafael J. Wysocki)
- restore the status of PCI devices across hibernation (Chen Yu)
- keep parent resources that start at 0x0 (Ard Biesheuvel)
- enable ECRC only if device supports it (Bjorn Helgaas)
- restore PRI and PASID state after Function-Level Reset (CQ Tang)
- skip DPC event if device is not present (Keith Busch)
- check domain when matching SMBIOS info (Sujith Pandel)
- mark Intel XXV710 NIC INTx masking as broken (Alex Williamson)
- avoid AMD SB7xx EHCI USB wakeup defect (Kai-Heng Feng)
- work around long-standing Macbook Pro poweroff issue (Bjorn Helgaas)
- add Switchtec "running" status flag (Logan Gunthorpe)
- fix dra7xx incorrect RW1C IRQ register usage (Arvind Yadav)
- modify xilinx-nwl IRQ chip for legacy interrupts (Bharat Kumar
Gogada)
- move VMD SRCU cleanup after bus, child device removal (Jon Derrick)
- add Faraday clock handling (Linus Walleij)
- configure Rockchip MPS and reorganize (Shawn Lin)
- limit Qualcomm TLP size to 2K (hardware issue) (Srinivas Kandagatla)
- support Tegra MSI 64-bit addressing (Thierry Reding)
- use Rockchip normal (not privileged) register bank (Shawn Lin)
- add HiSilicon Kirin SoC PCIe controller driver (Xiaowei Song)
- add Sigma Designs Tango SMP8759 PCIe controller driver (Marc
Gonzalez)
- add MediaTek PCIe host controller support (Ryder Lee)
- add Qualcomm IPQ4019 support (John Crispin)
- add HyperV vPCI protocol v1.2 support (Jork Loeser)
- add i.MX6 regulator support (Quentin Schulz)
* tag 'pci-v4.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (113 commits)
PCI: tango: Add Sigma Designs Tango SMP8759 PCIe host bridge support
PCI: Add DT binding for Sigma Designs Tango PCIe controller
PCI: rockchip: Use normal register bank for config accessors
dt-bindings: PCI: Add documentation for MediaTek PCIe
PCI: Remove __pci_dev_reset() and pci_dev_reset()
PCI: Split ->reset_notify() method into ->reset_prepare() and ->reset_done()
PCI: xilinx: Make of_device_ids const
PCI: xilinx-nwl: Modify IRQ chip for legacy interrupts
PCI: vmd: Move SRCU cleanup after bus, child device removal
PCI: vmd: Correct comment: VMD domains start at 0x10000, not 0x1000
PCI: versatile: Add local struct device pointers
PCI: tegra: Do not allocate MSI target memory
PCI: tegra: Support MSI 64-bit addressing
PCI: rockchip: Use local struct device pointer consistently
PCI: rockchip: Check for clk_prepare_enable() errors during resume
MAINTAINERS: Remove Wenrui Li as Rockchip PCIe driver maintainer
PCI: rockchip: Configure RC's MPS setting
PCI: rockchip: Reconfigure configuration space header type
PCI: rockchip: Split out rockchip_pcie_cfg_configuration_accesses()
PCI: rockchip: Move configuration accesses into rockchip_pcie_cfg_atu()
...
|
|
All wmi_services are not printing when we give below command.
cat /sys/kernel/debug/ieee80211/phyX/ath10k/wmi_services
This patch increases the buffer_len to 8192 to print all the wmi_services.
Signed-off-by: Tamizh chelvam <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Copy engine is a host to target communication interface
between wlan firmware and wlan wcn3990 platform driver. Add copy
engine register map for wcn3990 wlan module. This add support
for the copy engine source/destination ring configuration for
wcn3990 chipset.
Signed-off-by: Govind Singh <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Remove bus specific dependencies from CE layer
to have common CE layer across multiple targets.
This is required for adding support for WCN3990
chipset support as WCN3990 chipset uses SNOC
bus interface with Copy Engine endpoint.
Signed-off-by: Govind Singh <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Commit 59ae1d127ac0 ("networking: introduce and use skb_put_data()") introduced
a new checkpatch warning:
drivers/net/wireless/ath/ath10k/wmi.c:3308: code indent should use tabs where possible
Fix that.
Signed-off-by: Kalle Valo <[email protected]>
|
|
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
|
|
The pci_error_handlers->reset_notify() method had a flag to indicate
whether to prepare for or clean up after a reset. The prepare and done
cases have no shared functionality whatsoever, so split them into separate
methods.
[bhelgaas: changelog, update locking comments]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Christoph Hellwig <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Final set of patches for 4.13
* Some important fixes for 9000 HW;
* FW API changes for the upcoming -30 ucode release;
* A few new PCI IDs for 9000 series;
* Reorganization of common files;
* Some more fixes and improvements here and there
* Initialization and other important fixes for 9000 series;
* Support for version 30 of the FW API for 8000 and 9000 series;
|
|
We should not copy the MCS set from hostapd RX-STBC. We
have to just use the MCS set supported by the hardware.
This fixes an issue, where mwifiex is advertising wrong
MCS sets in beacons.
Fixes: 474a41e94dfc ("mwifiex: update MCS set as per RX-STBC bit from hostapd")
Signed-off-by: Ganapathi Bhat <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
The driver used cfg80211_connect_result() which is basically a wrapper
around cfg80211_connect_done() passing a subset of the information that
can be passed. For upcoming functionality this is not sufficient so
switching to use cfg80211_connect_done().
Reviewed-by: Hante Meuleman <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Reviewed-by: Franky Lin <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Adding callbacks for PMK provisioning. If firmware supports offloading
it is indicated to user-space that 802.1X offload is supported.
Signed-off-by: Arend van Spriel <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
The firmware may have supplicant code built-in. This is detected
by the driver and indicated in the wiphy features flags. User-space
can use this flag to determine whether or not to provide the
pre-shared key material in the nl80211 CONNECT command.
Reviewed-by: Gautam (Gautam Kumar) Shukla <[email protected]>
Reviewed-by: Hante Meuleman <[email protected]>
Reviewed-by: Pieter-Paul Giesberts <[email protected]>
Signed-off-by: Arend van Spriel <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Bump the maximum API supported by these device families to 33.
Signed-off-by: Luca Coelho <[email protected]>
|
|
The newest devices need a longer time to reset because of
their more complex hardware. Wait 5ms after device reset.
Consolidate all the places that reset the device in the
PCIe transport to avoid future bugs.
While at it, unify the flow to use set_bit instead of full
write as requested by the hardware designers.
Signed-off-by: Emmanuel Grumbach <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
iwl_pcie_apm_init can fail so make sure that the caller
takes the status into account.
Also, ensure that the error that iwl_pcie_apm_init can emit
will appear in the kernel log by default.
Signed-off-by: Emmanuel Grumbach <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
When a station that's not associated sends a data frame (e.g. an NDP)
hostapd will respond with a disassoc frame, telling it that it's not
associated. The station might also not be authenticated, in which case
there will not be a station entry for it, and as a result we need to
accept such frames without a station.
Fixes: 3ee0f0e23e4f ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
The API has changed - update the code.
Signed-off-by: Liad Kaufman <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
When we get a non-STA frame to transmit in client mode, we try to use
the IWL_MVM_DQA_BSS_CLIENT_QUEUE queue (queue #4). However, at this
point, the queue might not be allocated at all, causing warnings. The
scenario on which this happened was a race condition between mac80211
and our queue allocation work:
* mac80211 sends auth
* we stop mac80211 queues to allocate a hw queue
* authentication is aborted
* we allocate HW queue and start mac80211 queues
* mac80211 removes station
* mac80211 hands us the auth frame from the pending queue
At this point, since mac80211 has already removed the station, we try
to transmit the frame through this special non-station case on queue
4 anyway.
In order to really use it properly, we'd have to again go through the
hw queue allocation work, and attach it to a station, etc. In this
case that isn't possible (there's no station anymore), but if this
special case were needed, then we'd have to do it this way.
However, the special case is documented to exist for TDLS, but can't
trigger there because the TDLS setup frames etc. are normal to-DS
frames going to the peer through the AP. Testing also confirms that
this code path isn't triggered in TDLS.
Therefore, remove the code path to avoid using an unused queue. The
erroneous frame described above will still be transmitted on the AUX
queue, but arguably that's a mac80211 problem, which will eventually
be fixed by moving everything there to TXQs.
Fixes: e3118ad74d7e ("iwlwifi: mvm: support tdls in dqa mode")
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
When we get large sends on non-QoS association, we had a
bug that mangled the SNAP header. Fix that.
Fixes: a6d5e32f247c ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
When going into suspend, the HW configuration for MSI-X will
likely be lost. As a consequence, after waking up, all IRQ
causes will be mapped to interrupt 0, and as a consequence we
don't notice the interrupt because in most cases this is an
interrupt for a queue, and getting it doesn't read the other
cause registers.
Fixes: 2e5d4a8f61dc ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
Getting the TID of a packet before we know it is a QoS data
packet isn't a good idea. Delay the TID retrieval until
we know the packet is a QoS data packet.
Fixes: bb81bb68f472 ("iwlwifi: mvm: add Tx A-MSDU inside A-MPDU")
Signed-off-by: Emmanuel Grumbach <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
When in non-DQA mode, mac80211 actually gets a pretty much perfect
idea (in vif->hw_queue/cab_queue) of which queues we're using. But
in DQA mode, this isn't true - nonetheless, we were adding all the
queues, even the ones stations are using, to the queue allocation
bitmap.
Fix this, we should only add the queues we really are using in DQA
mode:
* IWL_MVM_OFFCHANNEL_QUEUE, as we use this in both modes
* mvm->aux_queue, as we use this in both modes - mac80211
never really knows about it but we use it as a cookie
internally, so can't reuse it
* possibly the GCAST queue (cab_queue)
* all the "queues" we told mac80211 about we were using on each
interface (vif->hw_queue), these are entirely virtual in this
mode
Also add back the failure now when we can't allocate any more of
these - now virtual - queues; this was skipped in DQA mode and
would lead to having multiple ACs or even interfaces use the same
queue number in mac80211 (10, since that's the limit), which would
stop far too many queues if stopped.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
There may be a difference between the mac80211 vif->cab_queue and
mvmvif->cab_queue, particularly with TVQM. Make the code map this
earlier, instead of first returning the mac80211 one again from
iwl_mvm_get_ctrl_vif_queue().
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
In the driver, we track which hardware queue is associated with
which mac80211 "hw_queue", in order to be able to stop and wake
it. When moving these bitmaps out of the queue_info structures,
the type of the bitmap was erroneously changed from u32 to u8,
presumably in order to save memory.
Turns out that u32 isn't needed, because the highest queue we
can ever tell mac80211 is always < 16, but a u16 definitely is
needed, queues >=8 do happen.
While at it, throw a BUILD_BUG_ON() into the place where we set
the limit (mvm->first_agg_queue) and a warning when it actually
gets put into the bitmap.
The consequence of this bug is that full HW queues associated
with such a too-high mac80211 number never stop higher layer
queues when full, and thus would simply drop all packets that
couldn't be enqueued to the hardware queue.
Fixes: 34e10860ae8d ("iwlwifi: mvm: remove references to queue_info in new TX path")
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
The code was intended to enable IP header checksumming on AMSDUs, but
failed to really do so because the A-MSDU bit was set after all the
checksumming bits, and thus checking for A-MSDU could never be true.
Fix this by setting the A-MSDU bit before the offload bits.
Fixes: 5e6a98dc4863 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Reported-by: Emmanuel Grumbach <[email protected]>
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
We have tracing for both pre-ICT and ICT interrupts, including all
the data read there. Extend the tracing to MSI-X interrupts.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
When hostapd adds a station, it does so before sending the association
response frame, so that it can indicate the correct status code in the
response.
However, when this then fails, or the association response already is
a reject for some other reason, then there's no station entry and thus
no per-station management queue to send the response on and it must be
sent on the probe response queue. The code should therefore not warn.
In theory, we could check and warn if the status code is success, but
that seems excessive, so just relax the check to allow any association
response frames.
Fixes: 3ee0f0e23e4f ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
Only a000-series devices were going to use this, but actually
initialize using the context info, which includes paging, so
this code is never invoked; remove it.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
Since we now support 8 device families, move their configuration
files into a new subdirectory "cfg".
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
Move the notification wait code into the new fw interaction directory.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
There's a lot of mvm code that really should be more generic
and part of the iwlwifi module. Start by making a place to
keep such code - in the new "fw" subdirectory - and already
move the firmware related header files there.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|