Age | Commit message (Collapse) | Author | Files | Lines |
|
There's either the pldr_sync case, in which case we didn't want
or do the retry loops anyway, or things will just continue to
fail. Remove the retry loop that was added in a previous attempt
to address the issue that was later (though still a bit broken)
addressed by the pldr_sync case.
Signed-off-by: Johannes Berg <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20240123200528.f80a88a18799.I48f21eda090f4cc675f40e99eef69a986d21b500@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
If the STEP (the interface between MAC and PHY) is in URM
(a lower speed mode) then we cannot use 320 MHz MCS > 9.
Therefore, limit the MCS in our capabilities in this case.
Note that this also limits the TX/rate scaling since that
takes both TX and RX capabilities into account.
Signed-off-by: Johannes Berg <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20240123200528.02bae683b7fc.Id5efbb71d45da02c8c4e211d20396637ddd44da8@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
The driver should not send 160 MHz BW support for 5 GHz
band in HE if PCI subsystem device ID indicates no 160 MHz support.
Signed-off-by: Mukesh Sisodiya <[email protected]>
Reviewed-by: Mordechay Goodstein <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20240126085924.77c248ce6986.I558e8d0cf19dc862b1c4124df78a4cb690095bb2@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
There's no need to print this, it's a known issue and
the workaround works just fine. Make the reallocation
message just a debug message.
Signed-off-by: Johannes Berg <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20240123200528.329d5f2ee7f7.I0bfc6dde17fe2c738129f3aba746c6cba57589f9@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
Add support for the new 802.11be device with limites capabilities:
- 320 MHz isn't supported
- MCSs 12 and 13 are not supported
Signed-off-by: Mukesh Sisodiya <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20240123200528.8529bd2acedf.I25dccb7bbeb21b8df2123fad51dde7fcf137a508@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
We used to have a test built into the code for this internally,
but now we can put that into kunit and let everyone run it, to
verify the devinfo table ordering if it's changed.
Signed-off-by: Johannes Berg <[email protected]>
Reviewed-by: Benjamin Berg <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20240123200528.a4a8af7c091f.I0fb09083317b331168b99b8db39656a126a5cc4d@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.9
The first "new features" pull request for v6.9. We have only driver
changes this time and most of them are for Realtek drivers. Really
nice to see activity in Broadcom drivers again.
Major changes:
rtwl8xxxu
* RTL8188F: concurrent interface support
* Channel Switch Announcement (CSA) support in AP mode
brcmfmac
* per-vendor feature support
* per-vendor SAE password setup
rtlwifi
* speed up USB firmware initialisation
* tag 'wireless-next-2024-01-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (105 commits)
wifi: iwlegacy: Use kcalloc() instead of kzalloc()
wifi: rtw89: fix disabling concurrent mode TX hang issue
wifi: rtw89: fix HW scan timeout due to TSF sync issue
wifi: rtw89: add wait/completion for abort scan
wifi: rtw89: fix null pointer access when abort scan
wifi: rtw89: disable RTS when broadcast/multicast
wifi: rtw89: Set default CQM config if not present
wifi: rtw89: refine hardware scan C2H events
wifi: rtw89: refine add_chan H2C command to encode_bits
wifi: rtw89: 8922a: add BTG functions to assist BT coexistence to control TX/RX
wifi: rtw89: 8922a: add TX power related ops
wifi: rtw89: 8922a: add register definitions of H2C, C2H, page, RRSR and EDCCA
wifi: rtw89: 8922a: add chip_ops related to BB init
wifi: rtw89: 8922a: add chip_ops::{enable,disable}_bb_rf
wifi: rtw89: add mlo_dbcc_mode for WiFi 7 chips
wifi: rtlwifi: Speed up firmware loading for USB
wifi: rtl8xxxu: add missing number of sec cam entries for all variants
wifi: brcmfmac: allow per-vendor event handling
wifi: brcmfmac: avoid invalid list operation when vendor attach fails
wifi: brcmfmac: Demote vendor-specific attach/detach messages to info
...
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.8-rc2
The most visible fix here is the ath11k crash fix which was introduced
in v6.7. We also have a fix for iwlwifi memory corruption and few
smaller fixes in the stack.
* tag 'wireless-2024-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: fix race condition on enabling fast-xmit
wifi: iwlwifi: fix a memory corruption
wifi: mac80211: fix potential sta-link leak
wifi: cfg80211/mac80211: remove dependency on non-existing option
wifi: cfg80211: fix missing interfaces when dumping
wifi: ath11k: rely on mac80211 debugfs handling for vif
wifi: p54: fix GCC format truncation warning with wiphy->fw_version
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the purpose specific kcalloc() function instead of the argument
size * count in the kzalloc() function.
Also, it is preferred to use sizeof(*pointer) instead of sizeof(type)
due to the type of the variable can change and one needs not change the
former (unlike the latter).
Link: https://www.kernel.org/doc/html/next/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments [1]
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Erick Archer <[email protected]>
Reviewed-by: Gustavo A. R. Silva <[email protected]>
Acked-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://msgid.link/[email protected]
|
|
iwl_fw_ini_trigger_tlv::data is a pointer to a __le32, which means that
if we copy to iwl_fw_ini_trigger_tlv::data + offset while offset is in
bytes, we'll write past the buffer.
Cc: [email protected]
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218233
Fixes: cf29c5b66b9f ("iwlwifi: dbg_ini: implement time point handling")
Signed-off-by: Emmanuel Grumbach <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20240111150610.2d2b8b870194.I14ed76505a5cf87304e0c9cc05cc0ae85ed3bf91@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/broadcom/bnxt/bnxt.c
e009b2efb7a8 ("bnxt_en: Remove mis-applied code from bnxt_cfg_ntp_filters()")
0f2b21477988 ("bnxt_en: Fix compile error without CONFIG_RFS_ACCEL")
https://lore.kernel.org/all/[email protected]/
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.8
The third "new features" pull request for v6.8. This is a smaller one
to clear up our tree before the break and nothing really noteworthy
this time.
Major changes:
stack
* cfg80211: introduce cfg80211_ssid_eq() for SSID matching
* cfg80211: support P2P operation on DFS channels
* mac80211: allow 64-bit radiotap timestamps
iwlwifi
* AX210: allow concurrent P2P operation on DFS channels
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Cross-merge networking fixes after downstream PR.
Adjacent changes:
drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c
23c93c3b6275 ("bnxt_en: do not map packet buffers twice")
6d1add95536b ("bnxt_en: Modify TX ring indexing logic.")
tools/testing/selftests/net/Makefile
2258b666482d ("selftests: add vlan hw filter tests")
a0bc96c0cd6e ("selftests: net: verify fq per-band packet limit")
Signed-off-by: Paolo Abeni <[email protected]>
|
|
ENOTSUPP isn't a standard error code, don't use it. Replace with
EOPNOTSUPP instead.
Signed-off-by: Andrei Otcheretianski <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231219215605.a69f4347b5f8.I88429d5de8251287ec0b58ff26a588465b9049a5@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
The firmware can allow to clear the internal debug buffer. This can be
used to sanitize the data when requested to.
Signed-off-by: Emmanuel Grumbach <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231219215605.99aed3efbacb.Ib5bda1d1ff4bae476667737d4081ad066d1d7e6b@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
For now, this isn't allowed. The API to mac80211 isn't great
for this, but we need to change the API to move puncturing
into the chanctx/chandef, and will do it better then.
Signed-off-by: Johannes Berg <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231219215605.38955b68b429.I0c4ae99179b271648a747a51eb04853504c7952c@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
We don't want to duplicate the definitions later,
so add them to the API.
Signed-off-by: Johannes Berg <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231219215605.6595e905997b.I12354d31676911b29ab30c81a4e9b87f59284d3b@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
Add the CSR register details for new wifi7 devices and
correctly set rf_name for devices with FM and WP radios.
Signed-off-by: Mukesh Sisodiya <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231219215605.a9c04b1e9d13.Ibf258d5e6370d8840a2560282988a1c26377c410@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
We don't support such device.
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231219215605.6e6961ac0ac5.I923024eac20efd24a5b42332d8e73ae756e0469a@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
eSR is activated when a chanctx is assigned to more than one link.
During eSR activation we should disable RLC for both phys, and configure
the FW with a special phy command for both phys.
Currently we assign the phy_ctxt to the link only after eSR activation,
so RLC is not disabled for the new phy_ctxt, and a cmd is not sent to FW.
Fix this by first assigning the new phy_ctxt to the link and then
doing the eSR activation.
Fixes: 12bacfc2c065 ("wifi: iwlwifi: handle eSR transitions")
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231219215605.3d94507f5d9a.I537fcd73aedf94c7348c03157e486f24301fef14@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
The driver copies the userspace buffer into an internal NUL
byte terminated buffer. While doing so, it was reading beyond
the end of the userspace buffer, overwriting its own NUL
termination in the process.
Fix this by only copying the correct number of bytes.
Fixes: 3f244876ef73 ("wifi: iwlwifi: make debugfs entries link specific")
Signed-off-by: Anjaneyulu <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Reviewed-by: Benjamin Berg <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231219215605.e4913deb2ad4.Idcf6a7e909ff4b7801cd49c2f691f84a2f68eff9@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
It is possible that though multiple links are enabled we cannot enabled
EMLSR enable more than a single link, e.g., all valid links are on the
same band etc. Thus, do not warn in case no valid link pair is found.
Fixes: b9be67fb4207 ("wifi: iwlwifi: mvm: Add basic link selection logic")
Signed-off-by: Ilan Peer <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231219215605.142e57a05230.I7cfe78c94c3d15c4c744bccadd8f187e43594932@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
Now with the mac80211 locking model changed, we no longer can
cause any bad dependencies here between mvm->mutex and other
mutexes in mac80211, so we no longer need to drop the mutex
early or even temporarily. Clean this up.
Signed-off-by: Johannes Berg <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231219215605.1f2f5289ecc6.I7e3b8e806b6d50e88ba0c26767da8261806eb9c7@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
If we want to drop packets, that's surely a good thing to
do when we want to enter rfkill. Send this command despite
rfkill so we can successfully clean up everything, we need
to handle it separately since it has CMD_WANT_SKB, so it's
not going to automatically return success when in rfkill.
Fixes: d4e3a341b87b ("iwlwifi: mvm: add support for new flush queue response")
Signed-off-by: Johannes Berg <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231219215605.c528a6fa6cec.Ibe5e9560359ccc0fba60c35e01de285c376748a2@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
The NVM_CHANNEL_ACTIVE bit means that active scanning/beaconing is
allowed, however it's not an exact opposite of IEEE80211_CHAN_NO_IR.
For example, NVM_CHANNEL_ACTIVE bit is not set on DFS channels, while
cfg80211 doesn't really expect NO-IR on DFS channels.
Signed-off-by: Andrei Otcheretianski <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231219215605.94cd9b96a532.Ifb0e8d8a6a6384493758f26b811d58432536101a@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
AX210 devices allow concurrent P2P operation on DFS channels.
Signed-off-by: Andrei Otcheretianski <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231219215605.dc39b33bf507.I04dfda24d73091fb75701279d10ac400314de488@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
The firmware changed their mind, don't set the chains to zero,
instead set them to 1 as we normally would for connections to
APs that don't use MIMO.
Fixes: 2a7ce54ccc23 ("iwlwifi: mvm: honour firmware SMPS requests")
Signed-off-by: Johannes Berg <[email protected]>
Reviewed-by: Luciano Coelho <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231219215605.7f031f1a127f.Idc816e0f604b07d22a9d5352bc23c445512fad14@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.8
The second features pull request for v6.8. A bigger one this time with
changes both to stack and drivers. We have a new Wifi band RFI (WBRF)
mitigation feature for which we pulled an immutable branch shared with
other subsystems. And, as always, other new features and bug fixes all
over.
Major changes:
cfg80211/mac80211
* AMD ACPI based Wifi band RFI (WBRF) mitigation feature
* Basic Service Set (BSS) usage reporting
* TID to link mapping support
* mac80211 hardware flag to disallow puncturing
iwlwifi
* new debugfs file fw_dbg_clear
mt76
* NVMEM EEPROM improvements
* mt7996 Extremely High Throughpu (EHT) improvements
* mt7996 Wireless Ethernet Dispatcher (WED) support
* mt7996 36-bit DMA support
ath12k
* support one MSI vector
* WCN7850: support AP mode
* tag 'wireless-next-2023-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (207 commits)
wifi: mt76: mt7996: Use DECLARE_FLEX_ARRAY() and fix -Warray-bounds warnings
wifi: ath11k: workaround too long expansion sparse warnings
Revert "wifi: ath12k: use ATH12K_PCI_IRQ_DP_OFFSET for DP IRQ"
wifi: rt2x00: remove useless code in rt2x00queue_create_tx_descriptor()
wifi: rtw89: only reset BB/RF for existing WiFi 6 chips while starting up
wifi: rtw89: add DBCC H2C to notify firmware the status
wifi: rtw89: mac: add suffix _ax to MAC functions
wifi: rtw89: mac: add flags to check if CMAC and DMAC are enabled
wifi: rtw89: 8922a: add power on/off functions
wifi: rtw89: add XTAL SI for WiFi 7 chips
wifi: rtw89: phy: print out RFK log with formatted string
wifi: rtw89: parse and print out RFK log from C2H events
wifi: rtw89: add C2H event handlers of RFK log and report
wifi: rtw89: load RFK log format string from firmware file
wifi: rtw89: fw: add version field to BB MCU firmware element
wifi: rtw89: fw: load TX power track tables from fw_element
wifi: mwifiex: configure BSSID consistently when starting AP
wifi: mwifiex: add extra delay for firmware ready
wifi: mac80211: sta_info.c: fix sentence grammar
wifi: mac80211: rx.c: fix sentence grammar
...
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
On older devices (before unified image!) we can end up calling
stop_device from an rfkill interrupt. However, in stop_device
we attempt to synchronize IRQs, which then of course deadlocks.
Avoid this by checking the context, if running from the IRQ
thread then don't synchronize. This wouldn't be correct on a
new device since RSS is supported, but older devices only have
a single interrupt/queue.
Fixes: 37fb29bd1f90 ("wifi: iwlwifi: pcie: synchronize IRQs before NAPI")
Reviewed-by: Miri Korenblit <[email protected]>
Reviewed-by: Emmanuel Grumbach <[email protected]>
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://msgid.link/20231215111335.59aab00baed7.Iadfe154d6248e7f9dfd69522e5429dbbd72925d7@changeid
|
|
kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure.
Cc: Kunwu Chan <[email protected]>
Signed-off-by: Kunwu Chan <[email protected]>
Acked-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Newest firmware has completely offloaded this logic and this command
will be deprecated soon. Based on a capability bit advertised by the
firmware, skip this command.
Signed-off-by: Emmanuel Grumbach <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231207044813.e64ef70c0133.I9f47cdef2ba45f1f383b70023857376973de3a8c@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
There's only one user of this code, which is STA unblock
during sleep for uAPSD on really old devices. Instead of
having this all through the API with calls up and down,
just implemented a special-case CMD_BLOCK_TXQS flag for
this, it's only needed in the old gen1 transport.
While at it, fix a complain that lockdep would have, as
we lock the cmd queue and then the TXQs in the reclaim
by using spin_lock_nested(). We no longer need to disable
BHs in iwl_trans_pcie_block_txq_ptrs() since it's called
with them disabled already.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231207044813.2bd95e0570fc.I16486dbc82570d2f73a585872f5394698627310d@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
This causes fortify warnings when compiled against recent kernels
with recent compilers, and generally is not supported in the kernel
anymore.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231207044813.367a2c77b9be.I4964ec8ca1d30c7c3163f9873814c8205a1a14eb@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
This never returns an error and the return value is never
checked anyway, so it can just be void.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231207044813.898b7e99206f.I61378115093fe70e6f5baca7f334651e4190eb3b@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231207044813.a0e2198e9afd.I3bf737ba5ec1b3013218001e808f6bae0c834543@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
We shouldn't access the device if we don't hold a reference,
and if - after locking - we see that it has no bus, we also
can't do anything, in fact, pci_stop_and_remove_bus_device()
will be a no-op.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231207044813.6c0879e695f7.I1d3ce75ecad32a4cbf1b9dad61bfb7bc7821fdd9@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
This can be used by the user space when it wants to clear the data we
collected so far for privacy reasons.
Signed-off-by: Emmanuel Grumbach <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231207044813.d5e97d5ec0d9.I7a5e836e6109e1fce7e6301dba8d1f28e60a5440@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
When there's not going to be any data in the data event, we
don't need to add it at all (unlike the TX version, it has
no data at all.)
Also combine the tracing into a separate inline so we only
call iwl_rx_trace_len() once, which also simplifies things,
and lets us have a single place to later add other checks.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231207044813.13325a4848d2.Ic9e7d794fc4aebfe5ac5136b539ee62789f210f3@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
EHT CQI is one of the EHT PHY capabilities. We don't support EHT CQI.
The non-triggered CQI feedback bit was unset in a previous patch,
but the triggered CQI feedback bit wasn't. Unset it.
Fixes: 0e21ec6edbb5 ("wifi: iwlwifi: nvm: Update EHT capabilities for GL device")
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231207044813.092528daf59e.I5715769490835819beddb00c91bbc9e806e170cb@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
For an MLO connection, the BSSID of the link used during the scanning
should be used (and not the one from the default link).
Signed-off-by: Ilan Peer <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231207044813.1e67dba640c1.I6c4941bfab3a04498370e58b402c64d990c39fbf@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
If a valid link ID was provided in the scan request use it instead
of picking one of the active links.
Signed-off-by: Ilan Peer <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231207044813.84e21c01b79d.Ib5f546d35542c6c561f5b944c08c9b1850f44146@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
It possible that while the rx rb is being handled, the transport has
been stopped and re-started. In this case the tx queue pointer is not
yet initialized, which will lead to a NULL pointer dereference.
Fix it.
Signed-off-by: Avraham Stern <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231207044813.cd0898cafd89.I0b84daae753ba9612092bf383f5c6f761446e964@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
Evidently I had only looked at all the ones in rx.c, and missed this.
Add bh-disable to this use of the rxq->lock as well.
Fixes: 25edc8f259c7 ("iwlwifi: pcie: properly implement NAPI")
Reported-by: Brian Norris <[email protected]>
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231208183100.e79ad3dae649.I8f19713c4383707f8be7fc20ff5cc1ecf12429bb@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
Based on the deliberate `sizeof(dest) ... - 1` pattern we can see that
both dump_info->dev_human_readable and dump_info->bus_human_readable are
intended to be NUL-terminated.
Moreover, since this seems to cross the file boundary let's NUL-pad to
ensure no behavior change.
strscpy_pad() covers both the NUL-termination and NUL-padding, let's use
it.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://github.com/KSPP/linux/issues/90
Cc: [email protected]
Signed-off-by: Justin Stitt <[email protected]>
Reviewed-by: Kees Cook <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/20231019-strncpy-drivers-net-wireless-intel-iwlwifi-fw-dbg-c-v2-1-179b211a374b@google.com
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
wireless fixes:
- debugfs had a deadlock (removal vs. use of files),
fixes going through wireless ACKed by Greg
- support for HT STAs on 320 MHz channels, even if it's
not clear that should ever happen (that's 6 GHz), best
not to WARN()
- fix for the previous CQM fix that broke most cases
- various wiphy locking fixes
- various small driver fixes
* tag 'wireless-2023-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: use wiphy locked debugfs for sdata/link
wifi: mac80211: use wiphy locked debugfs helpers for agg_status
wifi: cfg80211: add locked debugfs wrappers
debugfs: add API to allow debugfs operations cancellation
debugfs: annotate debugfs handlers vs. removal with lockdep
debugfs: fix automount d_fsdata usage
wifi: mac80211: handle 320 MHz in ieee80211_ht_cap_ie_to_sta_ht_cap
wifi: avoid offset calculation on NULL pointer
wifi: cfg80211: hold wiphy mutex for send_interface
wifi: cfg80211: lock wiphy mutex for rfkill poll
wifi: cfg80211: fix CQM for non-range use
wifi: mac80211: do not pass AP_VLAN vif pointer to drivers during flush
wifi: iwlwifi: mvm: fix an error code in iwl_mvm_mld_add_sta()
wifi: mt76: mt7925: fix typo in mt7925_init_he_caps
wifi: mt76: mt7921: fix 6GHz disabled by the missing default CLC config
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.8
The first features pull request for v6.8. Not so big in number of
commits but we removed quite a few ancient drivers: libertas 16-bit
PCMCIA support, atmel, hostap, zd1201, orinoco, ray_cs, wl3501 and
rndis_wlan.
Major changes:
cfg80211/mac80211
- extend support for scanning while Multi-Link Operation (MLO) connected
* tag 'wireless-next-2023-11-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (68 commits)
wifi: nl80211: Documentation update for NL80211_CMD_PORT_AUTHORIZED event
wifi: mac80211: Extend support for scanning while MLO connected
wifi: cfg80211: Extend support for scanning while MLO connected
wifi: ieee80211: fix PV1 frame control field name
rfkill: return ENOTTY on invalid ioctl
MAINTAINERS: update iwlwifi maintainers
wifi: rtw89: 8922a: read efuse content from physical map
wifi: rtw89: 8922a: read efuse content via efuse map struct from logic map
wifi: rtw89: 8852c: read RX gain offset from efuse for 6GHz channels
wifi: rtw89: mac: add to access efuse for WiFi 7 chips
wifi: rtw89: mac: use mac_gen pointer to access about efuse
wifi: rtw89: 8922a: add 8922A basic chip info
wifi: rtlwifi: drop unused const_amdpci_aspm
wifi: mwifiex: mwifiex_process_sleep_confirm_resp(): remove unused priv variable
wifi: rtw89: regd: update regulatory map to R65-R44
wifi: rtw89: regd: handle policy of 6 GHz according to BIOS
wifi: rtw89: acpi: process 6 GHz band policy from DSM
wifi: rtlwifi: simplify rtl_action_proc() and rtl_tx_agg_start()
wifi: rtw89: pci: update interrupt mitigation register for 8922AE
wifi: rtw89: pci: correct interrupt mitigation register for 8852CE
...
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This error path should return -EINVAL instead of success.
Fixes: 57974a55d995 ("wifi: iwlwifi: mvm: refactor iwl_mvm_mac_sta_state_common()")
Signed-off-by: Dan Carpenter <[email protected]>
Acked-by: Gregory Greenman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
|
|
Variable len is not effectively used, so delete it.
drivers/net/wireless/intel/iwlegacy/4965-mac.c:4234:7: warning: variable 'len' set but not used.
Reported-by: Abaci Robot <[email protected]>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=7223
Signed-off-by: Jiapeng Chong <[email protected]>
Acked-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The commands should be sorted inside the group definition.
Fix the ordering so we won't get following warning:
WARN_ON(iwl_cmd_groups_verify_sorted(trans_cfg))
Link: https://lore.kernel.org/regressions/[email protected]/
Link: https://lore.kernel.org/linux-wireless/CAHk-=wix6kqQ5vHZXjOPpZBfM7mMm9bBZxi2Jh7XnaKCqVf94w@mail.gmail.com/
Fixes: b6e3d1ba4fcf ("wifi: iwlwifi: mvm: implement new firmware API for statistics")
Tested-by: Niklāvs Koļesņikovs <[email protected]>
Tested-by: Damian Tometzki <[email protected]>
Acked-by: Kalle Valo <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Signed-off-by: Emmanuel Grumbach <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|