| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In some platforms, having the device enabled with certain radio
frontends causes the platform to not be able to resume properly
from suspend, regardless of the wakeup cause. This was traced to
a hardware issue with the integrated 9000-series A-step variant.
Set the right hardware bit to disable the problematic state.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
Integrated chip may have different HW and RF steps.
Currently, the driver supports only different HW steps.
Add logic to support different RF steps enables combining different
HW and RF steps.
Signed-off-by: Haim Dreyfuss <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
Three configurations will share device ID 2720, and will
be differentiated by RF ID.
Signed-off-by: Sara Sharon <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
One of the RF modules we support has been deprecated and never
released publicly. Remove support for this module.
Signed-off-by: Luca Coelho <[email protected]>
|
|
Support differentiating between two phys for a000 devices
in order to load the correct firmware.
Eventually when moving completely to the new phy we will be
able to remove this.
Signed-off-by: Sara Sharon <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
In case the OS provides fewer interrupts than requested, different
causes will share the same interrupt vector as follow:
1.One interrupt less: non rx causes shared with FBQ.
2.Two interrupts less: non rx causes shared with FBQ and RSS.
3.More than two interrupts: we will use fewer RSS queues.
Also make the request depend on the number of online CPUs
instead of possible CPUs.
Signed-off-by: Haim Dreyfuss <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
Integrated 9000 devices have a bug with shadow registers
value retention.
If driver writes RBD registers while MAC is asleep the
values are stored in shadow registers to be copied whenever
MAC wakes up.
However, in 9000 devices a MAC wakeup is not triggered
and when the bus powers down due to inactivity the shadow
values and dirty bits are lost.
Turn on the chicken-bits that cause MAC wakeup for RX-related
values as well when the device is in D0.
When the device is in low power mode turn the RX wakeup chicken
bits off since driver is idle and this W/A is not needed.
Remove previous W/A which was ineffective.
Signed-off-by: Sara Sharon <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
Currently there is one to one function between device id to it's ucode.
The new generation devices allows to combine different phy and mac images.
Now we have two different ucode images with the same device id.
Read RF ID to identify phy image and overwrite it if needed.
Signed-off-by: Haim Dreyfuss <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
|
|
From 9000 family on, we need to get HW address from host
CSR registers.
OEM can override it by fusing the override registers - read
those first, and if those are 0 - read the OTP registers instead.
In addition - bail out if no valid mac address is present. Make
it shared for all NICs.
Signed-off-by: Sara Sharon <[email protected]>
Signed-off-by: Emmanuel Grumbach <[email protected]>
|
|
Working with MSIX requires prior configuration.
This includes requesting interrupt vectors from the OS,
registering the vectors and mapping the optional causes to the
relevant interrupt. In addition add new interrupt handler
to handle MSIX interrupt.
Signed-off-by: Haim Dreyfuss <[email protected]>
Signed-off-by: Emmanuel Grumbach <[email protected]>
|
|
[email protected] is not available anymore.
[email protected] should be used instead.
Signed-off-by: Emmanuel Grumbach <[email protected]>
|
|
Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <[email protected]>
|