| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
usbnet_cdc_update_filter was getting the interface number from the
usb_interface struct in cdc_state->control. However, cdc_ncm does
not initialize that structure in its bind function, but uses
cdc_ncm_ctx instead. Getting intf directly from struct usbnet solves
the problem.
Signed-off-by: Miguel Rodríguez Pérez <[email protected]>
Signed-off-by: Bjørn Mork <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
If ax88172a_unbind() fails, make sure that the return code is
less than zero so that cleanup is done properly and avoid UAF.
Fixes: a9a51bd727d1 ("ax88172a: fix information leak on short answers")
Signed-off-by: George Kennedy <[email protected]>
Reported-by: [email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
On sparc32, tcflag_t is "unsigned long", unlike on all other
architectures, where it is "unsigned int":
drivers/net/usb/hso.c: In function ‘hso_serial_set_termios’:
include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 4 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
^~~~~~~
include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 5 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
^~~~~~~
As "unsigned long" is 32-bit on sparc32, fix this by casting all tcflag_t
parameters to "unsigned int".
While at it, use "%u" to format unsigned numbers.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
All conflicts seemed rather trivial, with some guidance from
Saeed Mameed on the tc_ct.c one.
Signed-off-by: David S. Miller <[email protected]>
|
|
Add support for Quectel Wireless Solutions Co., Ltd. EG95 LTE modem
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0195 Rev=03.18
S: Manufacturer=Android
S: Product=Android
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
Signed-off-by: AceLan Kao <[email protected]>
Acked-by: Bjørn Mork <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In a case where the ID_REV register read is failed, the memory for a
private data structure has to be freed before returning error from the
function smsc95xx_bind.
Fixes: bbd9f9ee69242 ("smsc95xx: add wol support for more frame types")
Signed-off-by: Andre Edich <[email protected]>
Signed-off-by: Parthiban Veerasooran <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The return value of the function smsc95xx_reset() must be checked
to avoid returning false success from the function smsc95xx_bind().
Fixes: 2f7ca802bdae2 ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Andre Edich <[email protected]>
Signed-off-by: Parthiban Veerasooran <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Syzbot reports an use-after-free in workqueue context:
BUG: KASAN: use-after-free in mutex_unlock+0x19/0x40 kernel/locking/mutex.c:737
mutex_unlock+0x19/0x40 kernel/locking/mutex.c:737
__smsc95xx_mdio_read drivers/net/usb/smsc95xx.c:217 [inline]
smsc95xx_mdio_read+0x583/0x870 drivers/net/usb/smsc95xx.c:278
check_carrier+0xd1/0x2e0 drivers/net/usb/smsc95xx.c:644
process_one_work+0x777/0xf90 kernel/workqueue.c:2274
worker_thread+0xa8f/0x1430 kernel/workqueue.c:2420
kthread+0x2df/0x300 kernel/kthread.c:255
It looks like that smsc95xx_unbind() is freeing the structures that are
still in use by the concurrently running workqueue callback. Thus switch
to using cancel_delayed_work_sync() to ensure the work callback really
is no longer active.
Reported-by: [email protected]
Signed-off-by: Tuomas Tynkkynen <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Using a AX88179 device (0b95:1790), I see two bytes of appended data on
every RX packet. For example, this 48-byte ping, using 0xff as a
payload byte:
04:20:22.528472 IP 192.168.1.1 > 192.168.1.2: ICMP echo request, id 2447, seq 1, length 64
0x0000: 000a cd35 ea50 000a cd35 ea4f 0800 4500
0x0010: 0054 c116 4000 4001 f63e c0a8 0101 c0a8
0x0020: 0102 0800 b633 098f 0001 87ea cd5e 0000
0x0030: 0000 dcf2 0600 0000 0000 ffff ffff ffff
0x0040: ffff ffff ffff ffff ffff ffff ffff ffff
0x0050: ffff ffff ffff ffff ffff ffff ffff ffff
0x0060: ffff 961f
Those last two bytes - 96 1f - aren't part of the original packet.
In the ax88179 RX path, the usbnet rx_fixup function trims a 2-byte
'alignment pseudo header' from the start of the packet, and sets the
length from a per-packet field populated by hardware. It looks like that
length field *includes* the 2-byte header; the current driver assumes
that it's excluded.
This change trims the 2-byte alignment header after we've set the packet
length, so the resulting packet length is correct. While we're moving
the comment around, this also fixes the spelling of 'pseudo'.
Signed-off-by: Jeremy Kerr <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <[email protected]>
|
|
Add support for Telit LE910C1-EUX composition
0x1031: tty, tty, tty, rmnet
Signed-off-by: Daniele Palmas <[email protected]>
Acked-by: Bjørn Mork <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <[email protected]>
|
|
Device id 0927 is the RTL8153B-based component of the 'Surface USB-C to
Ethernet and USB Adapter' and may be used as a component of other devices
in future. Tested and working with the r8152 driver.
Update the cdc_ether blacklist due to the RTL8153 'network jam on suspend'
issue which this device will cause (personally confirmed).
Signed-off-by: Marc Payne <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <[email protected]>
|
|
If a MAC address was passed via the device tree node for the r8152
device, use it and fall back to reading from EEPROM otherwise. This is
useful for devices where the r8152 EEPROM was not programmed with a
valid MAC address, or if users want to explicitly set a MAC address in
the bootloader and pass that to the kernel.
Signed-off-by: Thierry Reding <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The variable status is being initializeed with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <[email protected]>
Acked-by: Bjørn Mork <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The variable ret is being initializeed with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The variable ret is being initializeed with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
If you do not find the OUT endpoint, you should say so,
rather than copy the error message for the IN endpoint.
Presumably a copy and paste error.
Signed-off-by: Oliver Neukum <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Conflicts were all overlapping changes.
Signed-off-by: David S. Miller <[email protected]>
|
|
There's no callers in-tree
Signed-off-by: YueHaibing <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add support for Dell Wireless 5816e to drivers/net/usb/qmi_wwan.c
Signed-off-by: Matt Jolly <[email protected]>
Acked-by: Bjørn Mork <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The vendor driver does upon failing to read a valid MAC address from
EEPROM write the netdev's address back to EEPROM and invoking a EEPROM
reload operation. Based on this we can implement the ethtool_ops
set_eeprom and provide the means to populate the EEPROM from within
Linux.
It's worth noting that ax88179_get_eeprom() will return some default
data unless the content of the EEPROM is deemed "complete", so until the
EEPROM is fully populated (e.g. by running ethtool -e | ethtool -E)
data written with ax88179_set_eeprom() will appear not to stick.
The implementation is based on asix_set_eeprom(), from asix_common.c
Signed-off-by: Bjorn Andersson <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Remove pegasus' own workqueue and replace it with system_long_wq.
Signed-off-by: Petko Manolov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <[email protected]>
|
|
ASKEY WWHC050 is a mcie LTE modem.
The oem configuration states:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1690 ProdID=7588 Rev=ff.ff
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=813f0eef6e6e
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
Tested on openwrt distribution.
Signed-off-by: Cezary Jackiewicz <[email protected]>
Signed-off-by: Pawel Dembicki <[email protected]>
Acked-by: Bjørn Mork <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The ndp32->wLength is two bytes long, so replace cpu_to_le32 with cpu_to_le16.
Fixes: 0fa81b304a79 ("cdc_ncm: Implement the 32-bit version of NCM Transfer Block")
Signed-off-by: Alexander Bersenev <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Minor overlapping changes, nothing serious.
Signed-off-by: David S. Miller <[email protected]>
|
|
The NCM specification defines two formats of transfer blocks: with 16-bit
fields (NTB-16) and with 32-bit fields (NTB-32). Currently only NTB-16 is
implemented.
This patch adds the support of NTB-32. The motivation behind this is that
some devices such as E5785 or E5885 from the current generation of Huawei
LTE routers do not support NTB-16. The previous generations of Huawei
devices are also use NTB-32 by default.
Also this patch enables NTB-32 by default for Huawei devices.
During the 2019 ValdikSS made five attempts to contact Huawei to add the
NTB-16 support to their router firmware, but they were unsuccessful.
Signed-off-by: Alexander Bersenev <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <[email protected]>
Acked-by: Hayes Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Dell USB Type C docking WD19/WD19DC attaches additional peripherals as:
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M
|__ Port 1: Dev 11, If 0, Class=Hub, Driver=hub/4p, 5000M
|__ Port 3: Dev 12, If 0, Class=Hub, Driver=hub/4p, 5000M
|__ Port 4: Dev 13, If 0, Class=Vendor Specific Class,
Driver=r8152, 5000M
where usb 2-1-3 is a hub connecting all USB Type-A/C ports on the dock.
When hotplugging such dock with additional usb devices already attached on
it, the probing process may reset usb 2.1 port, therefore r8152 ethernet
device is also reset. However, during r8152 device init there are several
for-loops that, when it's unable to retrieve hardware registers due to
being disconnected from USB, may take up to 14 seconds each in practice,
and that has to be completed before USB may re-enumerate devices on the
bus. As a result, devices attached to the dock will only be available
after nearly 1 minute after the dock was plugged in:
[ 216.388290] [250] r8152 2-1.4:1.0: usb_probe_interface
[ 216.388292] [250] r8152 2-1.4:1.0: usb_probe_interface - got id
[ 258.830410] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): PHY not ready
[ 258.830460] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Invalid header when reading pass-thru MAC addr
[ 258.830464] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Get ether addr fail
This happens in, for example, r8153_init:
static int generic_ocp_read(struct r8152 *tp, u16 index, u16 size,
void *data, u16 type)
{
if (test_bit(RTL8152_UNPLUG, &tp->flags))
return -ENODEV;
...
}
static u16 ocp_read_word(struct r8152 *tp, u16 type, u16 index)
{
u32 data;
...
generic_ocp_read(tp, index, sizeof(tmp), &tmp, type | byen);
data = __le32_to_cpu(tmp);
...
return (u16)data;
}
static void r8153_init(struct r8152 *tp)
{
...
if (test_bit(RTL8152_UNPLUG, &tp->flags))
return;
for (i = 0; i < 500; i++) {
if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) &
AUTOLOAD_DONE)
break;
msleep(20);
}
...
}
Since ocp_read_word() doesn't check the return status of
generic_ocp_read(), and the only exit condition for the loop is to have
a match in the returned value, such loops will only ends after exceeding
its maximum runs when the device has been marked as disconnected, which
takes 500 * 20ms = 10 seconds in theory, 14 in practice.
To solve this long latency another test to RTL8152_UNPLUG flag should be
added after those 20ms sleep to skip unnecessary loops, so that the device
probe can complete early and proceed to parent port reset/reprobe process.
This can be reproduced on all kernel versions up to latest v5.6-rc2, but
after v5.5-rc7 the reproduce rate is dramatically lowered to 1/30 or less
while it was around 1/2.
Signed-off-by: You-Sheng Yang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <[email protected]>
|
|
usbnet creates network interfaces with min_mtu = 0 and
max_mtu = ETH_MAX_MTU.
These values are not modified by qmi_wwan when the network interface
is created initially, allowing, for example, to set mtu greater than 1500.
When a raw_ip switch is done (raw_ip set to 'Y', then set to 'N') the mtu
values for the network interface are set through ether_setup, with
min_mtu = ETH_MIN_MTU and max_mtu = ETH_DATA_LEN, not allowing anymore to
set mtu greater than 1500 (error: mtu greater than device maximum).
The patch restores the original min/max mtu values set by usbnet after a
raw_ip switch.
Signed-off-by: Daniele Palmas <[email protected]>
Acked-by: Bjørn Mork <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Use new helper tcp_v6_gso_csum_prep in additional network drivers.
Signed-off-by: Heiner Kallweit <[email protected]>
Acked-by: Hayes Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
We have been using the fact that the QMI and DIAG functions
usually are the only ones with class/subclass/protocol being
ff/ff/ff on Quectel modems. This has allowed us to match the
QMI function without knowing the exact interface number,
which can vary depending on firmware configuration.
The ability to silently reject the DIAG function, which is
usually handled by the option driver, is important for this
method to work. This is done based on the knowledge that it
has exactly 2 bulk endpoints. QMI function control interfaces
will have either 3 or 1 endpoint. This rule is universal so
the quirk condition can be removed.
The fixed layouts known from the Gobi1k and Gobi2k modems
have been gradually replaced by more dynamic layouts, and
many vendors now use configurable layouts without changing
device IDs. Renaming the class/subclass/protocol matching
macro makes it more obvious that this is now not Quectel
specific anymore.
Cc: Kristian Evensen <[email protected]>
Cc: Aleksander Morgado <[email protected]>
Signed-off-by: Bjørn Mork <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit f25e1392fdb5 removed the support for the pre-production variant
of the Dell DW5821e to avoid probing another USB interface unnecessarily.
However, the pre-production samples are found in the wild, and this lack
of support is causing problems for users of such samples. It is therefore
necessary to support both variants.
Matching on both interfaces 0 and 1 is not expected to cause any problem
with either variant, as only the QMI function will be probed successfully
on either. Interface 1 will be rejected based on the HID class for the
production variant:
T: Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev=03.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
And interface 0 will be rejected based on too few endpoints for the
pre-production variant:
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev= 3.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
Fixes: f25e1392fdb5 ("qmi_wwan: fix interface number for DW5821e production firmware")
Link: https://whrl.pl/Rf0vNk
Reported-by: Lars Melin <[email protected]>
Cc: Aleksander Morgado <[email protected]>
Signed-off-by: Bjørn Mork <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Device 0xa387 also supports MAC passthrough, therefore add it to the
whitelst.
BugLink: https://bugs.launchpad.net/bugs/1827961/comments/30
Signed-off-by: Kai-Heng Feng <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Minor conflict in mlx5 because changes happened to code that has
moved meanwhile.
Signed-off-by: David S. Miller <[email protected]>
|
|
When enabling this, the device would wait an internal signal which
wouldn't be triggered. Then, the device couldn't enter P3 mode, so
the power consumption is increased.
Signed-off-by: Hayes Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Avoid the MCU to clear the lanwake after suspending. It may cause the
WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it
and reset the lanwake status when resuming or initializing.
Signed-off-by: Hayes Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
For certain platforms, it causes USB reset periodically.
Signed-off-by: Hayes Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
For RTL8153B with QFN32, disable test IO. Otherwise, it may cause
abnormal behavior for the device randomly.
Signed-off-by: Hayes Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
PLA MCU clock speed down could only be enabled when tx/rx are disabled.
Otherwise, the packet loss may occur.
Signed-off-by: Hayes Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Enable U2P3 may miss zero packet for bulk-in.
Signed-off-by: Hayes Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Initailization would reset runtime suspend by tp->saved_wolopts, so
the tp->saved_wolopts should be set before initializing.
Signed-off-by: Hayes Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When linking ON, the patch of flow control has to be reset. This
makes sure the patch works normally.
Signed-off-by: Hayes Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|