| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Set adapter NAPI state as disabled if they are removed. This will allow
them to be enabled again if reallocated in case of a hard reset.
Signed-off-by: Thomas Falcon <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
t4_prep_fw doesn't check for card_fw pointer before store the read data,
which could lead to a NULL pointer dereference if kvzalloc failed.
Signed-off-by: YueHaibing <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch change the API for ndo_xdp_xmit to support bulking
xdp_frames.
When kernel is compiled with CONFIG_RETPOLINE, XDP sees a huge slowdown.
Most of the slowdown is caused by DMA API indirect function calls, but
also the net_device->ndo_xdp_xmit() call.
Benchmarked patch with CONFIG_RETPOLINE, using xdp_redirect_map with
single flow/core test (CPU E5-1650 v4 @ 3.60GHz), showed
performance improved:
for driver ixgbe: 6,042,682 pps -> 6,853,768 pps = +811,086 pps
for driver i40e : 6,187,169 pps -> 6,724,519 pps = +537,350 pps
With frames avail as a bulk inside the driver ndo_xdp_xmit call,
further optimizations are possible, like bulk DMA-mapping for TX.
Testing without CONFIG_RETPOLINE show the same performance for
physical NIC drivers.
The virtual NIC driver tun sees a huge performance boost, as it can
avoid doing per frame producer locking, but instead amortize the
locking cost over the bulk.
V2: Fix compile errors reported by kbuild test robot <[email protected]>
V4: Isolated ndo, driver changes and callers.
Signed-off-by: Jesper Dangaard Brouer <[email protected]>
Signed-off-by: Alexei Starovoitov <[email protected]>
|
|
Sandbox QP Commands are retired in the order they are sent. Outstanding
commands are stored in a linked-list in the order they appear. Once a
response is received and the callback gets called, we pull the first
element off the pending list, assuming they correspond.
Sending a message and adding it to the pending list is not done atomically,
hence there is an opportunity for a race between concurrent requests.
Bind both send and add under a critical section.
Fixes: bebb23e6cb02 ("net/mlx5: Accel, Add IPSec acceleration interface")
Signed-off-by: Yossi Kuperman <[email protected]>
Signed-off-by: Adi Nissim <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
When RXFCS feature is enabled, the HW do not strip the FCS data,
however it is not present in the checksum calculated by the HW.
Fix that by manually calculating the FCS checksum and adding it to the SKB
checksum field.
Add helper function to find the FCS data for all SKB forms (linear,
one fragment or more).
Fixes: 102722fc6832 ("net/mlx5e: Add support for RXFCS feature flag")
Signed-off-by: Eran Ben Elisha <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Add dcbnl's set/get buffer configuration callback that allows user to
set/get buffer size configuration and priority to buffer mapping.
By default, firmware controls receive buffer configuration and priority
of buffer mapping based on the changes in pfc settings. When set buffer
call back is triggered, the buffer configuration changes to manual mode.
The manual mode means mlx5 driver will adjust the buffer configuration
accordingly based on the changes in pfc settings.
ConnectX buffer stride is 128 Bytes. If the buffer size is not multiple
of 128, the buffer size will be rounded down to the nearest multiple of
128.
Signed-off-by: Huy Nguyen <[email protected]>
Reviewed-by: Parav Pandit <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Add APIs for buffer configuration based on the changes in
pfc configuration, cable len, buffer size configuration,
and priority to buffer mapping.
Note that the xoff fomula is as below
xoff = ((301+2.16 * len [m]) * speed [Gbps] + 2.72 MTU [B]
xoff_threshold = buffer_size - xoff
xon_threshold = xoff_threshold - MTU
Signed-off-by: Huy Nguyen <[email protected]>
Reviewed-by: Parav Pandit <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Add firmware command interface to read and write PPTB and PBMC
registers.
PPTB register enables mappings priority to a specific receive buffer.
PBMC registers enables changing the receive buffer's configuration such
as buffer size, xon/xoff thresholds, buffer's lossy property and
buffer's shared property.
Signed-off-by: Huy Nguyen <[email protected]>
Reviewed-by: Parav Pandit <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Move four below functions from en_ethtool.c to en/port.c. These
functions are used by both en_ethtool.c and en_main.c. Future code
can use these functions without ethtool link mode dependency.
u32 mlx5e_port_ptys2speed(u32 eth_proto_oper);
int mlx5e_port_linkspeed(struct mlx5_core_dev *mdev, u32 *speed);
int mlx5e_port_max_linkspeed(struct mlx5_core_dev *mdev, u32 *speed);
u32 mlx5e_port_speed2linkmodes(u32 speed);
Delete the speed field from table mlx5e_build_ptys2ethtool_map. This
table only keeps the mapping between the mlx5e link mode and
ethtool link mode. Add new table mlx5e_link_speed for translation
from mlx5e link mode to actual speed.
Signed-off-by: Huy Nguyen <[email protected]>
Reviewed-by: Parav Pandit <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux into for-next
mlx5-updates-2018-05-17
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <[email protected]>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
* tag 'mlx5-updates-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5e: Explicitly set source e-switch in offloaded TC rules
net/mlx5: Add source e-switch owner
net/mlx5e: Explicitly set destination e-switch in FDB rules
net/mlx5: Add destination e-switch owner
net/mlx5: Properly handle a vport destination when setting FTE
net/mlx5: Add merged e-switch cap
IB/mlx5: Use 'kvfree()' for memory allocated by 'kvzalloc()'
net/mlx5: Eswitch, Use 'kvfree()' for memory allocated by 'kvzalloc()'
net/mlx5: Vport, Use 'kvfree()' for memory allocated by 'kvzalloc()'
|
|
After changing speed to 100Mbps as a result of auto-negotiation (AN),
some 10/100/1000Mbps SFPs indicate a successful link (no faults or loss
of signal), but cannot successfully transmit or receive data. These
SFPs required an extra auto-negotiation (AN) after the speed change in
order to operate properly. Add a quirk for these SFPs so that if the
outcome of the AN actually results in changing to a new speed, re-initiate
AN at that new speed.
Signed-off-by: Tom Lendacky <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Instead of using a quirk to make the BelFuse 1GBT-SFP06 part look like
a 1000baseX part, program the SFP PHY to support SGMII and 10/100/1000
baseT.
Signed-off-by: Tom Lendacky <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When a KR re-driver is present, indicate the FEC support is available
during auto-negotiation.
Signed-off-by: Tom Lendacky <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Link training is always attempted when in KR mode, but the code is
structured to check if link training has been enabled before attempting
to perform it. Since that check will always be true, simplify the code
to always enable and start link training during KR auto-negotiation.
Signed-off-by: Tom Lendacky <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add ethtool support to show and set the device channel configuration.
Changing the channel configuration will result in a device restart.
Signed-off-by: Tom Lendacky <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In order to support being able to dynamically set/change the number of
Rx and Tx channels, update the code to:
- Move alloc and free of device memory into callable functions
- Move setting of the real number of Rx and Tx channels to device startup
- Move mapping of the RSS channels to device startup
Signed-off-by: Tom Lendacky <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add ethtool support to show and set the number of the Rx and Tx ring
descriptors. Changing the ring configuration will result in a device
restart.
Signed-off-by: Tom Lendacky <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add support to get SFP module information using ethtool.
Signed-off-by: Tom Lendacky <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The driver currently sets an indication of whether the SFP supports, and
that the driver can obtain, diagnostics data. This isn't currently used
by the driver and the logic to set this indicator is flawed because the
field is cleared each time the SFP is checked and only set when a new SFP
is detected. Remove this field and the logic supporting it.
Signed-off-by: Tom Lendacky <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The comm_owned field can hide logic where double locking is attempted
and prevent multiple threads for the same device from accessing the
mutex properly. Remove the comm_owned field and use the mutex API
exclusively for gaining ownership. The current driver has been audited
and is obtaining communications ownership properly.
Signed-off-by: Tom Lendacky <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Read and save the port property registers once during the device probe
and then use the saved values as they are needed.
Signed-off-by: Tom Lendacky <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
A debug output print statement uses the wrong variable to output the
maximum Rx channel count (cut and paste error, basically). Fix the
statement to use the proper variable.
Signed-off-by: Tom Lendacky <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
trigger an L1 configure operation when a transceiver module
is inserted in order to cause current "sticky" options like
Requested Forward Error Correction to be reapplied.
Signed-off-by: Casey Leedom <[email protected]>
Signed-off-by: Ganesh Goudar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
MDI Port Capabilities bit definitions were inconsistent with
regard to the MDI enum values. 2 bits used to define MDI in
the port capabilities are not really separable, it's a 2-bit
field with 4 different values. Change the port capability bit
definitions to be "AUTO" and "STRAIGHT" in order to get them
to line up with the enum's.
Signed-off-by: Casey Leedom <[email protected]>
Signed-off-by: Ganesh Goudar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
spin_lock/unlock was used instead of spin_un/lock_irq
in a procedure used in process space, on a spinlock
which can be grabbed in an interrupt.
This caused the stack trace below to be displayed (on kernel
4.17.0-rc1 compiled with Lock Debugging enabled):
[ 154.661474] WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
[ 154.668909] 4.17.0-rc1-rdma_rc_mlx+ #3 Tainted: G I
[ 154.675856] -----------------------------------------------------
[ 154.682706] modprobe/10159 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
[ 154.690254] 00000000f3b0e495 (&(&qp_table->lock)->rlock){+.+.}, at: mlx4_qp_remove+0x20/0x50 [mlx4_core]
[ 154.700927]
and this task is already holding:
[ 154.707461] 0000000094373b5d (&(&cq->lock)->rlock/1){....}, at: destroy_qp_common+0x111/0x560 [mlx4_ib]
[ 154.718028] which would create a new lock dependency:
[ 154.723705] (&(&cq->lock)->rlock/1){....} -> (&(&qp_table->lock)->rlock){+.+.}
[ 154.731922]
but this new dependency connects a SOFTIRQ-irq-safe lock:
[ 154.740798] (&(&cq->lock)->rlock){..-.}
[ 154.740800]
... which became SOFTIRQ-irq-safe at:
[ 154.752163] _raw_spin_lock_irqsave+0x3e/0x50
[ 154.757163] mlx4_ib_poll_cq+0x36/0x900 [mlx4_ib]
[ 154.762554] ipoib_tx_poll+0x4a/0xf0 [ib_ipoib]
...
to a SOFTIRQ-irq-unsafe lock:
[ 154.815603] (&(&qp_table->lock)->rlock){+.+.}
[ 154.815604]
... which became SOFTIRQ-irq-unsafe at:
[ 154.827718] ...
[ 154.827720] _raw_spin_lock+0x35/0x50
[ 154.833912] mlx4_qp_lookup+0x1e/0x50 [mlx4_core]
[ 154.839302] mlx4_flow_attach+0x3f/0x3d0 [mlx4_core]
Since mlx4_qp_lookup() is called only in process space, we can
simply replace the spin_un/lock calls with spin_un/lock_irq calls.
Fixes: 6dc06c08bef1 ("net/mlx4: Fix the check in attaching steering rules")
Signed-off-by: Jack Morgenstein <[email protected]>
Signed-off-by: Tariq Toukan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add 0x6088 and 0x6089 device ids for new T6 cards.
Signed-off-by: Ganesh Goudar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Trivial fix to spelling mistake in mlx4_dbg debug message and also
change the phrasing of the message so that is is more readable
Signed-off-by: Colin Ian King <[email protected]>
Reviewed-by: Tariq Toukan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When enabling the sub-CRQ IRQ a previous update sent a H_EOI prior
to the enablement to clear any pending interrupts that may be present
across a partition migration. This fixed a firmware bug where a
migration could erroneously indicate that a H_EOI was pending.
The H_EOI should only be sent when enabling during a mobility
event though. Doing so at other time could wrong and can produce
extra driver output when IRQs are enabled when doing TX completion.
Signed-off-by: Nathan Fontenot <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Rename VXGE_HW_ERR_PRIVILAGED_OPEARATION to VXGE_HW_ERR_PRIVILEGED_OPERATION
to fix spelling mistake.
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When NFP is modelled as a switch we assign phys_port_name to respective
port(representor )s:
vNIC0 - | - PF port (pf%d) MAC/PHY (p%d[s%d]) - |E==
In most cases there is only one vNIC for communication with the switch.
If there is more than one we need to be able to identify them. Use %d
as phys_port_name of the vNICs.
We don't have to pass ID to nfp_net_debugfs_vnic_add() separately any
more.
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Dirk van der Merwe <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
PCI PFs can host more than one logical endpoint. In NFP terms
this means having more than one vNIC for PCIe PF. The vNICs
are usually corresponding 1:1 to Ethernet ports. In core NIC
we use the legacy idea of vNIC *being* the Ethernet port,
hence netdevs put pX(sY) in their phys_port_name, like Ethernet
ports would. When ASIC ports are fully represented we need to
be able to name different PCIe PF ports, too. Use a scheme
similar to Ethernet ports - pfXsY, for PCIe PF number X,
sub-port Y.
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Dirk van der Merwe <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Current control firmware does not cater too well to multi-host
applications. There is no way to check which hosts are up or
otherwise negotiate what the state of the external port (the
Ethernet port) should be. Make sure the link is up when driver
loads, and don't take it down when Ethernet port netdev is
closed.
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Dirk van der Merwe <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
To configure buffering points we need full set of netdevs:
ASIC
user netdev -- | -- PCIe port MAC port -- | --
Configuring egrees qdiscs on user netdev configures standard
Linux TC software qdiscs, configuring PCIe port qdiscs will
provide a way of setting ASIC queuing parameters for PCIe block.
MAC port netdev egress qdiscs correspond to ASIC MAC Traffic
Manager block.
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Dirk van der Merwe <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Our previous apps all assumed to use only one eswitch mode (legacy
or switchdev) without the ability to change it. ABM NIC will
want to support the switch so plumb devlink_eswitch_mode_set through.
The devlink_eswitch_mode_set is expected to spawn representors and
potentially devlink ports so it's called under big devlink lock and
pf->lock.
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Dirk van der Merwe <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
nfp_apps can currently associate their structures with vNICs but
not representors. Add app priv pointer to representors as well.
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Dirk van der Merwe <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
ABM NIC requires more complex vNIC handling, allocate
per-vNIC structure. Find out RX queue base and PCI PF id.
There will be multiple PFs sharing the same MAC port, therefore
the MAC address assigned to the vNIC must be looked up in the
HWInfo database.
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Dirk van der Merwe <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add a very rudimentary active buffer management NIC support.
For now it's like a core NIC without SR-IOV support. Next
commits will extend its functionality.
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Dirk van der Merwe <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Current code doesn't enforce length requirements on 32bit accesses
with action NFP_CPP_ACTION_RW to memory units, but if the access
is only aligned to 4 bytes as well we will fall into the explicit
access case and error out. Such accesses are correct, allow them
by lowering the width earlier.
While at it use a switch statement to improve readability.
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Dirk van der Merwe <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Allow app FW to advertise its shared buffer pool information.
Use the per-PF mailbox to configure them from devlink.
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When working with devlink-related functionality for locking reasons
it's easier to create a new mailbox per-PCI PF device than try to
use one of the netdev/vNIC mailboxes.
Define new mailbox structure and resolve its symbol during probe.
For forward compatibility allow silent truncation of mailbox command
data.
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
nfp_net_pf_rtsym_read_optional() and nfp_net_pf_map_rtsym() are not
really related to networking code. Move them to the PF code and
remove the net from their names. They will soon be needed by code
outside of nfp_net_main.c anyway.
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds callbacks for providing the ethernet protocol driver TLVs.
Signed-off-by: Sudarsana Reddy Kalluru <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
MFW requests the TLVs in interrupt context. Extracting of the required
data from upper layers and populating of the TLVs require process context.
The patch adds work-queues for processing the tlv requests. It also adds
the implementation for requesting the tlv values from appropriate protocol
driver.
Signed-off-by: Sudarsana Reddy Kalluru <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: Sudarsana Reddy Kalluru <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: Sudarsana Reddy Kalluru <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The patch adds driver support for processing TLV requests/repsonses
from the mfw and upper driver layers respectively. The implementation
reads the requested TLVs from the shared memory, requests the values
from upper layer drivers, populates this info (TLVs) shared memory and
notifies MFW about the TLV values.
Signed-off-by: Sudarsana Reddy Kalluru <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The patch adds required management firmware (MFW) interfaces such as
mailbox commands, TLV types etc.
Signed-off-by: Sudarsana Reddy Kalluru <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-05-22
This series contains updates to i40e only.
Jake provides all the changes in this series starting with making it
consistent in how we approach the bit lock. Fixed the reporting of the
VEB statistics and the queue statistics to always return every queue
even if it is not currently in use. Use WARN_ONCE() so that the first
time we end up with an incorrect size we will dump a stack trace and a
message to help highlight the issue early in testing. Folded the fixed
string prefix into the stat string definition. Instead of using a
separate char *p pointer when copying strings, use the data pointer
directly. Added code comments for several of the statistic functions to
better explain the number and ordering of statistics.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Make sure to invoke pci_disable_device() when errors occur in
pcnet32_probe_pci().
Signed-off-by: Bo Chen <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
ILT entry requires 12 bit right shifted physical address.
Existing mask for ILT entry of physical address i.e.
ILT_ENTRY_PHY_ADDR_MASK is not sufficient to handle 64bit
address because upper 8 bits of 64 bit address were getting
masked which resulted in completer abort error on
PCIe bus due to invalid address.
Fix that mask to handle 64bit physical address.
Fixes: fe56b9e6a8d9 ("qed: Add module with basic common support")
Signed-off-by: Shahed Shaikh <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|