| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The usual devm_regulator_get() call already handles "optional"
regulators by returning a valid dummy and printing a warning
that the dummy regulator should be described properly. This
code open coded the same behaviour, but masked any errors that
are not -EPROBE_DEFER and is quite noisy.
This change effectively unmasks and propagates regulators errors
not involving -ENODEV, downgrades the error print to warning level
if no regulator is specified and captures the probe defer message
for /sys/kernel/debug/devices_deferred.
Fixes: 2e12f536635f ("net: stmmac: dwmac-rk: Use standard devicetree property for phy regulator")
Signed-off-by: Sebastian Reichel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The clock requesting code is quite repetitive. Fix this by requesting
the clocks via devm_clk_bulk_get_optional. The optional variant has been
used, since this is effectively what the old code did. The exact clocks
required depend on the platform and configuration. As a side effect
this change adds correct -EPROBE_DEFER handling.
Suggested-by: Jakub Kicinski <[email protected]>
Suggested-by: Andrew Lunn <[email protected]>
Fixes: 7ad269ea1a2b ("GMAC: add driver for Rockchip RK3288 SoCs integrated GMAC")
Signed-off-by: Sebastian Reichel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Static code analyzer complains to unchecked return value.
The result of pci_reset_function() is unchecked.
Despite, the issue is on the FLR supported code path and in that
case reset can be done with pcie_flr(), the patch uses less invasive
approach by adding the result check of pci_reset_function().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 7e2cf4feba05 ("qlcnic: change driver hardware interface mechanism")
Signed-off-by: Denis Plotnikov <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Reviewed-by: Bjorn Helgaas <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There is a new ICM area for that memory, so we need to handle it as we
did for the others ICM types.
The patch added that specific pool with its requirements and management.
Signed-off-by: Muhammad Sammar <[email protected]>
Signed-off-by: Yevgeny Kliteynik <[email protected]>
Reviewed-by: Alex Vesker <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
The send engine should be ready to handle more opcodes
in addition to RDMA_WRITE/RDMA_READ.
Signed-off-by: Yevgeny Kliteynik <[email protected]>
Reviewed-by: Alex Vesker <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
In STEv1 counter action can be set either by filling counter ID on STE, in
which case it is executed before other actions on this STE, or as a single
action, in which case it is executed in accordance with the actions order.
FW steering on STEv1 devices implements counter as counter ID on STE, and
this counter is set on the last STE.
Fix SMFS to be consistent with this behaviour - move TX counter to the
last STE, this way the counter will include all actions of the previous STEs
that might have changed packet headers length, e.g. encap, vlan push, etc.
Signed-off-by: Yevgeny Kliteynik <[email protected]>
Reviewed-by: Alex Vesker <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Create a new profile for SFs in order to disable the command cache.
Each function command cache consumes ~500KB of memory, when using a
large number of SFs this savings is notable on memory constarined
systems.
Use a new profile to provide for future differences between SFs and PFs.
The mr_cache not used for non-PF functions, so it is excluded from the
new profile.
Signed-off-by: Parav Pandit <[email protected]>
Reviewed-by: Bodong Wang <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Pass target struct net_device to mdb attach/detach handler in order to
expose the port name to the new tracepoints. Implemented following
tracepoints:
- Attach mdb to port.
- Detach mdb from port.
Usage example:
># cd /sys/kernel/debug/tracing
># echo mlx5:mlx5_esw_bridge_port_mdb_attach >> set_event
># cat trace
...
kworker/0:0-19071 [000] ..... 259004.253848: mlx5_esw_bridge_port_mdb_attach: net_device=enp8s0f0_0 addr=33:33:ff:00:00:01 vid=0 num_ports=1 offloaded=1
Signed-off-by: Vlad Buslov <[email protected]>
Reviewed-by: Maor Dickman <[email protected]>
Reviewed-by: Roi Dayan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Implement support for add/del SWITCHDEV_OBJ_ID_PORT_MDB events. For mdb
destination addresses configure egress table rules to replicate to per-port
multicast tables of all ports that are member of the multicast group as
illustrated by 'MDB1' rule in the following diagram:
+--------+--+
+---------------------------------------> Port 1 | |
| +-^------+--+
| |
| |
+-----------------------------------------+ | +---------------------------+ |
| EGRESS table | | +--> PORT 1 multicast table | |
+----------------------------------+ +-----------------------------------------+ | | +---------------------------+ |
| INGRESS table | | | | | | | |
+----------------------------------+ | dst_mac=P1,vlan=X -> pop vlan, goto P1 +--+ | | FG0: | |
| | | dst_mac=P1,vlan=Y -> pop vlan, goto P1 | | | src_port=dst_port -> drop | |
| src_mac=M1,vlan=X -> goto egress +---> dst_mac=P2,vlan=X -> pop vlan, goto P2 +--+ | | FG1: | |
| ... | | dst_mac=P2,vlan=Y -> goto P2 | | | | VLAN X -> pop, goto port | |
| | | dst_mac=MDB1,vlan=Y -> goto mcast P1,P2 +-----+ | ... | |
+----------------------------------+ | | | | | VLAN Y -> pop, goto port +-------+
+-----------------------------------------+ | | | FG3: |
| | | matchall -> goto port |
| | | |
| | +---------------------------+
| |
| |
| | +--------+--+
+---------------------------------------> Port 2 | |
| +-^------+--+
| |
| |
| +---------------------------+ |
+--> PORT 2 multicast table | |
+---------------------------+ |
| | |
| FG0: | |
| src_port=dst_port -> drop | |
| FG1: | |
| VLAN X -> pop, goto port | |
| ... | |
| | |
| FG3: | |
| matchall -> goto port +-------+
| |
+---------------------------+
MDB is managed by extending mlx5 bridge to store an entry in
mlx5_esw_bridge->mdb_list linked list (used to iterate over all offloaded
MDBs) and mlx5_esw_bridge->mdb_ht hash table (used to lookup existing MDB
by MAC+VLAN). Every MDB entry can be attached to arbitrary amount of bridge
ports that are stored in mlx5_esw_bridge_mdb_entry->ports xarray in order
to allow both efficient lookup of the port and also iteration over all
ports that the entry is attached to. Every time MDB is attached/detached
to/from a port, the hardware rule is recreated with list of destinations
corresponding to all attached ports. When the entry is detached from the
last port it is removed from mdb and destroyed which means that the ports
xarray also acts as implicit reference counting mechanism.
Signed-off-by: Vlad Buslov <[email protected]>
Reviewed-by: Maor Dickman <[email protected]>
Reviewed-by: Roi Dayan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
When VLAN with 'untagged' flag is created on port also provision the
per-port multicast table rule to pop the VLAN during packet replication.
This functionality must be in per-port table because some subset of ports
that are member of multicast group can require just a match on VLAN (trunk
mode) while other subset can be configured to remove the VLAN tag from
packets received on the ports (access mode).
Signed-off-by: Vlad Buslov <[email protected]>
Reviewed-by: Maor Dickman <[email protected]>
Reviewed-by: Roi Dayan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Multicast replication requires adding one more level of FDB_BR_OFFLOAD
priority flow tables. The new level is used for per-port multicast-specific
tables that have following flow groups structure (flow highest to lowest
priority):
- Flow group of size one that matches on source port metadata. This will
have a static single rule that prevent packets from being replicated to
their source port.
- Flow group of size one that matches all packets and forwards them to the
port that owns the table.
Initialize the table dynamically on all bridge ports when adding a port to
the bridge that has multicast enabled and on all existing bridge ports when
receiving multicast enable notification.
Signed-off-by: Vlad Buslov <[email protected]>
Reviewed-by: Maor Dickman <[email protected]>
Reviewed-by: Roi Dayan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Handle SWITCHDEV_ATTR_ID_BRIDGE_MC_DISABLED attribute notification to
dynamically toggle bridge multicast offload. Set new
MLX5_ESW_BRIDGE_MCAST_FLAG bridge flag when multicast offload is enabled.
Put multicast-specific code into new bridge_mcast.c file.
When initializing bridge multicast pipeline create a static rule for
snooping on IGMP traffic and three rules for snooping on MLD traffic (for
query, report and done message types). Note that matching MLD traffic
requires having flexparser MLX5_FLEX_PROTO_ICMPV6 capability enabled.
By default Linux bridge is created with multicast enabled which can be
modified by 'mcast_snooping' argument:
$ ip link set name my_bridge type bridge mcast_snooping 0
Signed-off-by: Vlad Buslov <[email protected]>
Reviewed-by: Maor Dickman <[email protected]>
Reviewed-by: Roi Dayan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
The pattern when function looks up a port by vport_num+vhca_id tuple in
order to just obtain its parent bridge is repeated multiple times in
bridge.c file. Further commits in this series use the pattern even more.
Extract the pattern to standalone mlx5_esw_bridge_from_port_lookup()
function to improve code readability.
This commits doesn't change functionality.
Signed-off-by: Vlad Buslov <[email protected]>
Reviewed-by: Maor Dickman <[email protected]>
Reviewed-by: Roi Dayan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Following patches in series will require accessing flow tables and groups
sizes, table levels and struct mlx5_esw_bridge from new the new source file
dedicated to multicast code. Expose these data in bridge_priv.h to reduce
clutter in following patches that will implement the actual functionality.
Signed-off-by: Vlad Buslov <[email protected]>
Reviewed-by: Maor Dickman <[email protected]>
Reviewed-by: Roi Dayan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
Bridge ingress and egress tables got more flow groups recently for QinQ
support and will get more in following patches of this series. Increase the
sizes of the tables to allow offloading more flows in each mode.
Signed-off-by: Vlad Buslov <[email protected]>
Reviewed-by: Maor Dickman <[email protected]>
Reviewed-by: Roi Dayan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|
|
The two constants accomplish the same thing.
Signed-off-by: Shailend Chand <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
n_addr is used to store be32 values,
so a sparse-friendly array of be32 to store these values.
Flagged by sparse:
.../mtk_ppe_debugfs.c:59:27: warning: incorrect type in assignment (different base types)
.../mtk_ppe_debugfs.c:59:27: expected unsigned int
.../mtk_ppe_debugfs.c:59:27: got restricted __be32 [usertype]
.../mtk_ppe_debugfs.c:161:46: warning: cast to restricted __be16
No functional changes intended.
Compile tested only.
Signed-off-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Drivers call netdev_tx_completed_queue() right before
netif_txq_maybe_wake(). If BQL is enabled netdev_tx_completed_queue()
should issue a memory barrier, so we can depend on that separating
the stop check from the consumer index update, instead of adding
another barrier in netif_txq_maybe_wake().
This matters more than the barriers on the xmit path, because
the wake condition is almost always true. So we issue the
consumer side barrier often.
Wrap netdev_tx_completed_queue() in a local helper to issue
the barrier even if BQL is disabled. Keep the same semantics
as netdev_tx_completed_queue() (barrier only if bytes != 0)
to make it clear that the barrier is conditional.
Plus since macro gets pkt/byte counts as arguments now -
we can skip waking if there were no packets completed.
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Convert bnxt to use new macros rather than open code the logic.
Two differences:
(1) bnxt_tx_int() will now only issue a memory barrier if it sees
enough space on the ring to wake the queue. This should be fine,
the mb() is between the writes to the ring pointers and checking
queue state.
(2) we'll start the queue instead of waking on race, this should
be safe inside the xmit handler.
Reviewed-by: Michael Chan <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Convert ixgbe to use the new macros, I think a lot of people
copy the ixgbe code. The only functional change is that the
unlikely() in ixgbe_clean_tx_irq() turns into a likely()
inside the new macro and no longer includes
total_packets && netif_carrier_ok(tx_ring->netdev)
which is probably for the best, anyway.
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Acked-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
anarion_config_dt()
Always return struct anarion_gmac * from anarion_config_dt().
In the case where ctl_block was an error pointer it was being
returned directly. Which sparse flags as follows:
.../dwmac-anarion.c:73:24: warning: incorrect type in return expression (different address spaces)
.../dwmac-anarion.c:73:24: expected struct anarion_gmac *
.../dwmac-anarion.c:73:24: got void [noderef] __iomem *[assigned] ctl_block
Avoid this by converting the error pointer to an error.
And then reversing the conversion.
As a side effect, the error can be used for logging purposes,
subjectively, leading to a minor cleanup.
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Use __iomem annotation the register base: the ctl_block field of struct
anarion_gmac. I believe this is the normal practice for such variables.
By doing so some casting is avoided.
And sparse no longer reports:
.../dwmac-anarion.c:29:23: warning: incorrect type in argument 1 (different address spaces)
.../dwmac-anarion.c:29:23: expected void const volatile [noderef] __iomem *addr
.../dwmac-anarion.c:29:23: got void *
.../dwmac-anarion.c:34:22: warning: incorrect type in argument 2 (different address spaces)
.../dwmac-anarion.c:34:22: expected void volatile [noderef] __iomem *addr
.../dwmac-anarion.c:34:22: got void *
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This was never used since the commit that added it - e58bb43f5e43
("stmmac: initial support to manage pcs modes").
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Leon Romanovsky says:
====================
Improve IPsec limits, ESN and replay window
This series overcomes existing hardware limitations in Mellanox ConnectX
devices around handling IPsec soft and hard limits.
In addition, the ESN logic is tied and added an interface to configure
replay window sequence numbers through existing iproute2 interface.
ip xfrm state ... [ replay-seq SEQ ] [ replay-oseq SEQ ]
[ replay-seq-hi SEQ ] [ replay-oseq-hi SEQ ]
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Leon Romanovsky <[email protected]>
* tag 'ipsec-esn-replay' of https://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5e: Simulate missing IPsec TX limits hardware functionality
net/mlx5e: Generalize IPsec work structs
net/mlx5e: Reduce contention in IPsec workqueue
net/mlx5e: Set IPsec replay sequence numbers
net/mlx5e: Remove ESN callbacks if it is not supported
xfrm: don't require advance ESN callback for packet offload
net/mlx5e: Overcome slow response for first IPsec ASO WQE
net/mlx5e: Add SW implementation to support IPsec 64 bit soft and hard limits
net/mlx5e: Prevent zero IPsec soft/hard limits
net/mlx5e: Factor out IPsec ASO update function
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
TI's J784S4 SoC supports USXGMII mode. Add USXGMII mode to the
extra_modes member of the J784S4 SoC data.
Configure MAC control register for supporting USXGMII mode and add
MAC_5000FD in the "mac_capabilities" member of struct "phylink_config".
Signed-off-by: Siddharth Vadapalli <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
TI's J784S4 SoC supports QSGMII mode with the CPSW9G instance of the
CPSW Ethernet Switch. Add a new compatible for J784S4 SoC and enable
QSGMII support for it by adding QSGMII mode to the extra_modes member of
the "j784s4_cpswxg_pdata" SoC data.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Move the interface mode specific configuration to the mac_config()
callback am65_cpsw_nuss_mac_config().
Also, do not reset the MAC Control register on mac_link_down(). Only
clear those bits that can possibly be set in mac_link_up().
Let the MAC remain in IDLE state after mac_link_down(). Bring it out of
the IDLE state on mac_link_up().
Signed-off-by: Siddharth Vadapalli <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The VLAN filters info is currently being held in a list and 2 bitmaps
(active_cvlans and active_svlans). We are experiencing some racing where
data is not in sync in the list and bitmaps. For example, the VLAN is
initially added to the list but only when the PF replies, it is added to
the bitmap. If a user adds many V2 VLANS before the PF responds:
while [ $((i++)) ]
ip l add l eth0 name eth0.$i type vlan id $i
we might end up with more VLAN list entries than the designated limit.
Also, The "ip link show" will show more links added than the PF limit.
On the other and, the bitmaps are only used to check the number of VLAN
filters and to re-enable the filters when the interface goes from DOWN to
UP.
This patch gets rid of the bitmaps and uses the list only. To do that,
the states of the VLAN filter are modified:
1 - IAVF_VLAN_REMOVE: the entry needs to be totally removed after informing
the PF. This is the "ip link del eth0.$i" path.
2 - IAVF_VLAN_DISABLE: (new) the netdev went down. The filter needs to be
removed from the PF and then marked INACTIVE.
3 - IAVF_VLAN_INACTIVE: (new) no PF filter exists, but the user did not
delete the VLAN.
Fixes: 48ccc43ecf10 ("iavf: Add support VIRTCHNL_VF_OFFLOAD_VLAN_V2 during netdev config")
Signed-off-by: Ahmed Zaki <[email protected]>
Tested-by: Rafal Romanowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The VLAN filter states are currently being saved as individual bits.
This is error prone as multiple bits might be mistakenly set.
Fix by replacing the bits with a single state enum. Also, add an
"ACTIVE" state for filters that are accepted by the PF.
Signed-off-by: Ahmed Zaki <[email protected]>
Tested-by: Rafal Romanowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
When a device is roaming between interfaces and a new flow entry is
created, we should assume that its output device is more up to date than
whatever entry existed already.
Signed-off-by: Felix Fietkau <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
WED version 2 (on MT7986 and later) can offload flows originating from
wireless devices.
In order to make that work, ndo_setup_tc needs to be implemented on the
netdevs. This adds the required code to offload flows coming in from WED,
while keeping track of the incoming wed index used for selecting the
correct PPE device.
Signed-off-by: Felix Fietkau <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Smatch reports: drivers/net/ethernet/sun/niu.c:4525
niu_alloc_channels() warn: missing unwind goto?
If niu_rbr_fill() fails, then we are directly returning 'err' without
freeing the channels.
Fix this by changing direct return to a goto 'out_err'.
Fixes: a3138df9f20e ("[NIU]: Add Sun Neptune ethernet driver.")
Signed-off-by: Harshit Mogalapalli <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2023-04-05
From Paul:
- TC action parsing cleanups
- Correctly report stats for missed packets
- Many CT actions limitations removed due to hw misses will now
continue from the relevant tc ct action in software.
From Adham:
- RQ/SQ devlink health diagnostics layout fixes
From Gal And Rahul:
- PTP code cleanup and cyclecounter shift value improvement
* tag 'mlx5-updates-2023-04-05' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Fix SQ SW state layout in SQ devlink health diagnostics
net/mlx5e: Fix RQ SW state layout in RQ devlink health diagnostics
net/mlx5e: Rename misleading skb_pc/cc references in ptp code
net/mlx5: Update cyclecounter shift value to improve ptp free running mode precision
net/mlx5e: Remove redundant macsec code
net/mlx5e: TC, Remove sample and ct limitation
net/mlx5e: TC, Remove mirror and ct limitation
net/mlx5e: TC, Remove tuple rewrite and ct limitation
net/mlx5e: TC, Remove multiple ct actions limitation
net/mlx5e: TC, Remove special handling of CT action
net/mlx5e: TC, Remove CT action reordering
net/mlx5e: CT: Use per action stats
net/mlx5e: TC, Move main flow attribute cleanup to helper func
net/mlx5e: TC, Remove unused vf_tun variable
net/mlx5e: Set default can_offload action
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
A recent rearrangement of includes has lead to a problem on m68k
as flagged by the kernel test robot.
Resolve this by moving the block asm includes to below linux includes.
A side effect i that non-Sparc asm includes are now immediately
before Sparc asm includes, which seems nice.
Using sparse v0.6.4 I was able to reproduce this problem as follows
using the config provided by the kernel test robot:
$ wget https://download.01.org/0day-ci/archive/20230404/[email protected]/config
$ cp config .config
$ make ARCH=m68k oldconfig
$ make ARCH=m68k C=2 M=drivers/net/ethernet/sun
CC [M] drivers/net/ethernet/sun/sunhme.o
In file included from drivers/net/ethernet/sun/sunhme.c:19:
./arch/m68k/include/asm/irq.h:78:11: error: expected ‘;’ before ‘void’
78 | asmlinkage void do_IRQ(int irq, struct pt_regs *regs);
| ^~~~~
| ;
./arch/m68k/include/asm/irq.h:78:40: warning: ‘struct pt_regs’ declared inside parameter list will not be visible outside of this definition or declaration
78 | asmlinkage void do_IRQ(int irq, struct pt_regs *regs);
| ^~~~~~~
Compile tested only.
Fixes: 1ff4f42aef60 ("net: sunhme: Alphabetize includes")
Reported-by: kernel test robot <[email protected]>
Link: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Signed-off-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Conflicts:
drivers/net/ethernet/google/gve/gve.h
3ce934558097 ("gve: Secure enough bytes in the first TX desc for all TCP pkts")
75eaae158b1b ("gve: Add XDP DROP and TX support for GQI-QPL format")
https://lore.kernel.org/all/[email protected]/
https://lore.kernel.org/all/[email protected]/
Adjacent changes:
net/can/isotp.c
051737439eae ("can: isotp: fix race between isotp_sendsmg() and isotp_release()")
96d1c81e6a04 ("can: isotp: add module parameter for maximum pdu size")
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Some DT devices already have phy device configured in the DT/ACPI.
Current implementation scans for a phy unconditionally even though
there is a phy listed in the DT/ACPI and already attached.
We should check the fwnode if there is any phy device listed in
fwnode and decide whether to scan for a phy to attach to.
Fixes: fe2cfbc96803 ("net: stmmac: check if MAC needs to attach to a PHY")
Reported-by: Martin Blumenstingl <[email protected]>
Link: https://lore.kernel.org/lkml/[email protected]/
Tested-by: Guenter Roeck <[email protected]>
Tested-by: Shahab Vahedi <[email protected]>
Tested-by: Marek Szyprowski <[email protected]>
Tested-by: Martin Blumenstingl <[email protected]>
Suggested-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Michael Sit Wei Hong <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
`dev_port` is used to differentiate devices that instantiate from
the same function, which is the case in most of NFP NICs.
In some customized scenario, `dev_port` is used to rename netdev
instead of `phys_port_name`. Example rules using `dev_port`:
SUBSYSTEM=="net", ACTION=="add", KERNELS=="0000:e1:00.0", ATTR{dev_port}=="0", NAME:="ens8np0"
SUBSYSTEM=="net", ACTION=="add", KERNELS=="0000:e1:00.0", ATTR{dev_port}=="1", NAME:="ens8np1"
To take port split case into account, here we initialize `dev_port`
according to the port sequence in eth_table from management firmware
instead of using port label id directly. And management firmware
makes sure that port sequence matches its label id.
Signed-off-by: Yinjun Zhang <[email protected]>
Acked-by: Simon Horman <[email protected]>
Signed-off-by: Louis Peens <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
ConnectX-7 devices don't have ability to send TX hard/soft limits
events. As a possible workaround, let's rely on existing infrastructure
and use periodic check of cached flow counter. In these periodic checks,
we call to xfrm_state_check_expire() to check and mark state accordingly.
Once the state is marked as XFRM_STATE_EXPIRED, the SA flow rule is
changed to drop all the traffic.
Link: https://lore.kernel.org/r/94a5d82c0c399747117d8a558f9beebfbcf26154.1680162300.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <[email protected]>
|
|
IPsec logic has two work structs which are submitted to same workqueue.
As a preparation to addition of new work which needs to be submitted
too, let's generalize struct mlx5e_ipsec_work.
Link: https://lore.kernel.org/r/285a1550242363de181bab3a07a69296f66ad9a8.1680162300.git.leonro@nvidia.com
Reviewed-by: Raed Salem <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
|
|
IPsec workqueue shouldn't be declared as ordered queue with one work
per-CPU, and can be safely changed to be unordered with default number
of works per-CPU.
Link: https://lore.kernel.org/r/5dc224a4decd09c14f645d38173e1a1710802cd8.1680162300.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <[email protected]>
|
|
"ip xfrm state ..." command allows users to configure replay sequence
numbers with replay-seq* arguments for RX and replay-oseq* for TX.
Add the needed driver logic to support setting them.
Link: https://lore.kernel.org/r/a9b17827eff2b29a4951225efa684a6cd38f74fe.1680162300.git.leonro@nvidia.com
Reviewed-by: Raed Salem <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
|
|
There is no need in implementation of .xdo_dev_state_advance_esn() and
setting work as it will never be called in packet offload mode.
Link: https://lore.kernel.org/r/2fc9fade32e31f03b100d6086a82ad36269349dc.1680162300.git.leonro@nvidia.com
Reviewed-by: Raed Salem <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
|
|
MAX_ORDER currently defined as number of orders page allocator supports:
user can ask buddy allocator for page order between 0 and MAX_ORDER-1.
This definition is counter-intuitive and lead to number of bugs all over
the kernel.
Change the definition of MAX_ORDER to be inclusive: the range of orders
user can ask from buddy allocator is 0..MAX_ORDER now.
[[email protected]: fix min() warning]
Link: https://lkml.kernel.org/r/20230315153800.32wib3n5rickolvh@box
[[email protected]: fix another min_t warning]
[[email protected]: fixups per Zi Yan]
Link: https://lkml.kernel.org/r/[email protected]
[[email protected]: fix underlining in docs]
Link: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Kirill A. Shutemov <[email protected]>
Reviewed-by: Michael Ellerman <[email protected]> [powerpc]
Cc: "Kirill A. Shutemov" <[email protected]>
Cc: Zi Yan <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
Queue reset was moved out from __init_dma_rx_desc_rings() and
__init_dma_tx_desc_rings() functions. Thus, the driver fails to transmit
and receive packet after XDP prog setup.
This commit adds the missing queue reset into stmmac_xdp_open() function.
Fixes: f9ec5723c3db ("net: ethernet: stmicro: stmmac: move queue reset to dedicated functions")
Cc: <[email protected]> # 6.0+
Signed-off-by: Song Yoong Siang <[email protected]>
Reviewed-by: Alexander Duyck <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The patch addresses an issue with the reset logic on the i.MX93 SoC, which
requires configuration of the correct interface speed under RMII mode to
complete the reset. The patch implements a fix_soc_reset function and uses
it specifically for the i.MX93 SoCs.
Reviewed-by: Fabio Estevam <[email protected]>
Signed-off-by: Shenwei Wang <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This patch adds support for platform-specific reset logic in the
stmmac driver. Some SoCs require a different reset mechanism than
the standard dwmac IP reset. To support these platforms, a new function
pointer 'fix_soc_reset' is added to the plat_stmmacenet_data structure.
The stmmac_reset in hwif.h is modified to call the 'fix_soc_reset'
function if it exists. This enables the driver to use the platform-specific
reset logic when necessary.
Signed-off-by: Shenwei Wang <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Not all fec MDIO bus drivers support C45 mode transactions. The older fec
hardware block in many ColdFire SoCs does not appear to support them, at
least according to most of the different ColdFire SoC reference manuals.
The bits used to generate C45 access on the iMX parts, in the OP field
of the MMFR register, are documented as generating non-compliant MII
frames (it is not documented as to exactly how they are non-compliant).
Commit 8d03ad1ab0b0 ("net: fec: Separate C22 and C45 transactions")
means the fec driver will always register c45 MDIO read and write
methods. During probe these will always be accessed now generating
non-compliant MII accesses on ColdFire based devices.
Add a quirk define, FEC_QUIRK_HAS_MDIO_C45, that can be used to
distinguish silicon that supports MDIO C45 framing or not. Add this to
all the existing iMX quirks, so they will be behave as they do now (*).
(*) it seems that some iMX parts may not support C45 transactions either.
The iMX25 and iMX50 Reference Manuals contain similar wording to
the ColdFire Reference Manuals on this.
Fixes: 8d03ad1ab0b0 ("net: fec: Separate C22 and C45 transactions")
Signed-off-by: Greg Ungerer <[email protected]>
Reviewed-by: Wei Fang <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Remove nesting level before SQ's SW state title and before SQ's SW
state capabilities line.
Preceding the SQ's SW state with a nameless nesting, wraps the inner SW
state map/dictionary with a nameless dictionary which is prohibited in
JSON file format.
Removing preceding SW state nest by removing function call
devlink_fmsg_obj_nest_start() and devlink_fmsg_obj_nest_end().
Signed-off-by: Adham Faris <[email protected]>
Reviewed-by: Tariq Toukan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
|