| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch simply demonstrates that a checksum value computed when
verifying an offloaded transport checksum value for both IPv4 and
IPv6 is (normally) 0. It can be squashed into the next patch.
Signed-off-by: Alex Elder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
With the ones' complement arithmetic, the sum of two negated values
is equal to the negation of the sum of the two original values [1].
Rearrange the calculation ip6_payload_sum using this property.
[1] https://tools.ietf.org/html/rfc1071
Signed-off-by: Alex Elder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In rmnet_map_ipv4_dl_csum_trailer(), remove the "csum_temp" and
"addend" local variables, and simplify a few lines of code.
Remove the "csum_temp", "csum_value", "ip6_hdr_csum", and "addend"
local variables in rmnet_map_ipv6_dl_csum_trailer(), and simplify a
few lines of code there as well.
Signed-off-by: Alex Elder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix the following kernel build warnings:
drivers/net/ethernet/ibm/ibmvnic.c:1516: warning: Function parameter or member 'skb' not described in 'build_hdr_descs_arr'
drivers/net/ethernet/ibm/ibmvnic.c:1516: warning: Function parameter or member 'indir_arr' not described in 'build_hdr_descs_arr'
drivers/net/ethernet/ibm/ibmvnic.c:1516: warning: Excess function parameter 'txbuff' description in 'build_hdr_descs_arr'
Signed-off-by: Lijun Pan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
drivers/net/ethernet/ibm/ibmvnic.c: In function ‘adapter_state_to_string’:
drivers/net/ethernet/ibm/ibmvnic.c:855:2: warning: enumeration value ‘VNIC_DOWN’ not handled in switch [-Wswitch]
855 | switch (state) {
| ^~~~~~
drivers/net/ethernet/ibm/ibmvnic.c: In function ‘reset_reason_to_string’:
drivers/net/ethernet/ibm/ibmvnic.c:1958:2: warning: enumeration value ‘VNIC_RESET_PASSIVE_INIT’ not handled in switch [-Wswitch]
1958 | switch (reason) {
| ^~~~~~
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Lijun Pan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Kernel-doc for intel_eth_pci_remove is incorrect, pdev datatype is
struct pci_dev. Changed it to the 'pci device pointer'.
Signed-off-by: Wong Vee Khee <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Currently some of the dwmac-intel definitions are in the header file,
while some are in the driver source file. Cleaning this by moving all
the definitions to the header file.
Signed-off-by: Wong Vee Khee <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
drivers/net/ethernet/ibm/ibmvnic.c: In function ‘handle_vpd_rsp’:
drivers/net/ethernet/ibm/ibmvnic.c:4393:3: warning: ‘strncpy’ output truncated before terminating nul copying 3 bytes from a string of the same length [-Wstringop-truncation]
4393 | strncpy((char *)adapter->fw_version, "N/A", 3 * sizeof(char));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Lijun Pan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There is no reason to embed an if within an if, we can just logically
AND the two conditions.
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Wong Vee Khee <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Reorder the variable declarations in descending line length order,
according to the networking coding style.
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Wong Vee Khee <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The struct mdio_xpcs_args is reminiscent of when a similarly named
struct mdio_xpcs_ops existed. Now that that is removed, we can shorten
the name to dw_xpcs (dw for DesignWare).
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In the previous patch IPv4 download checksum offload code was
updated to avoid unnecessary byte swapping, based on properties of
the Internet checksum algorithm. This patch makes comparable
changes to the IPv6 download checksum offload handling.
Signed-off-by: Alex Elder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Internet checksums are used for IPv4 header checksum, as well as TCP
segment and UDP datagram checksums. Such a checksum represents the
negated sum of adjacent pairs of bytes, using ones' complement
arithmetic.
One property of the Internet checkum is byte order independence [1].
Specifically, the sum of byte-swapped pairs is equal to the result
of byte swapping the sum of those same pairs when not byte-swapped.
So for example if a, b, c, d, y, and z are hexadecimal digits, and
PLUS represents ones' complement addition:
If: ab PLUS cd = yz
Then: ba PLUS dc = zy
For this reason, there is no need to swap the order of bytes in the
checksum value held in a message header, nor the one in the QMAPv4
trailer, in order to operate on them.
In other words, we can determine whether the hardware-computed
checksum matches the one in the message header without any byte
swaps.
(This patch leaves in place all existing type casts.)
[1] https://tools.ietf.org/html/rfc1071
Signed-off-by: Alex Elder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In rmnet_map_ipv6_dl_csum_trailer() there is an especially involved
line of code that determines the ones' complement sum of the IPv6
packet header (in host byte order). Simplify that by storing the
result of computing just the header checksum in a local variable,
then using that in the original assignment.
Use the size of the IPv6 header structure as the number of bytes to
checksum, rather than computing the offset to the transport header.
And use ip_fast_csum() rather than ipa_compute_csum(), knowing that
the size of an IPv6 header (40 bytes) is a multiple of 4 bytes
greater than 16.
Add some comments to match rmnet_map_ipv4_dl_csum_trailer().
Signed-off-by: Alex Elder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In rmnet_map_ipv4_dl_csum_trailer(), an illegal checksum subtraction
is done, subtracting hdr_csum (in host byte order) from csum_value (in
network byte order). Despite being illegal, it generally works,
because it turns out the value subtracted is (or should be) always 0,
which has the same representation in either byte order.
Doing illegal operations is not good form though, so fix this by
verifying the IP header checksum early in that function. If its
checksum is non-zero, the packet will be bad, so just return an
error. This will cause the packet to passed to the IP layer where
it can be dropped.
Thereafter, there is no need subtract the IP header checksum from
the checksum value in the trailer because we know it is zero.
Add a comment explaining this.
This type of packet error is different from other types, so add a
new statistics counter to track this condition.
Signed-off-by: Alex Elder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The checksum fields of the TCP and UDP header structures already
have type __sum16. We don't support any other protocol headers, so
we can simplify rmnet_map_get_csum_field(), getting rid of the local
variable entirely and just returning the appropriate address.
Signed-off-by: Alex Elder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The value passed as an argument to rmnet_map_ipv4_ul_csum_header()
is always an IPv4 header. Rather than using a local variable, just
have the type of the argument reflect the proper type.
In rmnet_map_ipv6_ul_csum_header() things are defined a little
differently, but make the same basic change there.
Signed-off-by: Alex Elder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
If IPV6 is not enabled in the kernel configuration, the RMNet
checksum code indicates a buffer containing an IPv6 packet is not
supported. The same thing happens if a buffer contains something
other than an IPv4 or IPv6 packet.
We can rearrange things a bit in two functions so that some #ifdef
calls can simply be eliminated.
Signed-off-by: Alex Elder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In rmnet_map_ipv4_dl_csum_trailer() use ip_is_fragment() to
determine whether a socket buffer contains a packet fragment.
Signed-off-by: Alex Elder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Jake Keller says:
====================
100GbE Intel Wired LAN Driver Updates 2021-06-11
Extend the ice driver to support basic PTP clock functionality for E810
devices.
This includes some tangential work required to setup the sideband queue and
driver shared parameters as well.
This series only supports E810-based devices. This is because other devices
based on the E822 MAC use a different and more complex PHY.
The low level device functionality is kept within ice_ptp_hw.c and is
designed to be extensible for supporting E822 devices in a future series.
This series also only supports very basic functionality including the
ptp_clock device and timestamping. Support for configuring periodic outputs
and external input timestamps will be implemented in a future series.
There are a couple of potential "what? why?" bits in this series I want to
point out:
1) the PTP hardware functionality is shared between multiple functions. This
means that the same clock registers are shared across multiple PFs. In order
to avoid contention or clashing between PFs, firmware assigns "ownership" to
one PF, while other PFs are merely "associated" with the timer. Because we
share the hardware resource, only the clock owner will allocate and register
a PTP clock device. Other PFs determine the appropriate PTP clock index to
report by using a firmware interface to read a shared parameter that is set
by the owning PF.
2) the ice driver uses its own kthread instead of using do_aux_work. This is
because the periodic and asynchronous tasks are necessary for all PFs, but
only one PF will allocate the clock.
The series is broken up into functional pieces to allow easy review.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Add support for setting a VF as a trusted VF by PF admin. Trusted VF
feature allows VFs to perform priviliged operations such as enabling
VF promiscuous mode, all-multicast mode and changing the VF MAC address
even if it was assigned by PF.
Signed-off-by: Hariprasad Kelam <[email protected]>
Signed-off-by: Naveen Mamindlapalli <[email protected]>
Signed-off-by: Sunil Kovvuri Goutham <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add new mailbox to enable PF to configure VF as trusted VF.
Trusted VF feature allows VFs to perform priviliged operations
such as enabling VF promiscuous mode, all-multicast mode and
changing the VF MAC address configured by PF. Refactored the
VF interface flags maintained by the AF driver such that the
flags do not overlap for various configurations.
Signed-off-by: Hariprasad Kelam <[email protected]>
Signed-off-by: Naveen Mamindlapalli <[email protected]>
Signed-off-by: Sunil Kovvuri Goutham <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add ndo_set_rx_mode callback handler to configure promisc, multicast and
allmulti options for VF driver. Also, modified PF driver ndo_set_rx_mode
handler to support multicast and promisc mode independently.
Signed-off-by: Naveen Mamindlapalli <[email protected]>
Signed-off-by: Sunil Kovvuri Goutham <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Currently, multicast packet filtering is accomplished by installing
MCAM rule that matches all-multicast MAC address and has its
NPC_RX_ACTION set to unicast to PF. Similarly promisc feature is
achieved by installing MCAM rule that matches all the traffic received
by the channel and unicast the packets to PF. This approach only applies
to PF and is not scalable across VFs.
This patch adds support for PF/VF multicast and promisc feature by
reserving NIX_RX_MCE_S entries from the global MCE list allocated
during NIX block initialization. The NIX_RX_MCE_S entries create a
linked list with a flag indicating the end of the list, and each entry
points to a PF_FUNC (either PF or VF). When a packet NPC_RX_ACTION is
set to MCAST, the corresponding NIX_RX_MCE_S list is traversed and the
packet is queued to each PF_FUNC available on the list.
The PF or VF driver adds the multicast/promisc packet match entry and
updates the MCE list with correspondng PF_FUNC. When a PF or VF interface
is disabled, the corresponding NIX_RX_MCE_S entry is removed from the
MCE list and the MCAM entry will be disabled if the list is empty.
Signed-off-by: Naveen Mamindlapalli <[email protected]>
Signed-off-by: Sunil Kovvuri Goutham <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The commit d96febedfde2 ("net: stmmac: arrange Tx tail pointer update
to stmmac_flush_tx_descriptors") introduced the following coverity
warning:-
1. Unintentional integer overflow (OVERFLOW_BEFORE_WIDEN)
overflow_before_widen: Potentially overflowing expression
'tx_q->cur_tx * desc_size' with type 'unsigned int' (32 bits,
unsigned) is evaluated using 32-bit arithmetic, and then used in a
context that expects an expression of type dma_addr_t (64 bits,
unsigned).
Fixed this by assigning tx_tail_addr to dma_addr_t type, as dma_addr_t
datatype is decided by CONFIG_ARCH_DMA_ADDR_T_64_BIT.
Fixes: d96febedfde2 ("net: stmmac: arrange Tx tail pointer update to stmmac_flush_tx_descriptors")
Signed-off-by: Wong Vee Khee <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Modify dpaa2_mac_get_node() to get the dpmac fwnode from either
DT or ACPI.
Modify dpaa2_mac_get_if_mode() to get interface mode from dpmac_node
which is a fwnode.
Modify dpaa2_pcs_create() to create pcs from dpmac_node fwnode.
Modify dpaa2_mac_connect() to support ACPI along with DT.
Signed-off-by: Calvin Johnson <[email protected]>
Signed-off-by: Ioana Ciornei <[email protected]>
Acked-by: Rafael J. Wysocki <[email protected]> # from the ACPI side
Acked-by: Grant Likely <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Depending on the device node type, call the specific OF or ACPI
mdiobus_register function.
Note: For both ACPI and DT cases, endianness of MDIO controllers
need to be specified using the "little-endian" property.
Signed-off-by: Calvin Johnson <[email protected]>
Signed-off-by: Ioana Ciornei <[email protected]>
Acked-by: Grant Likely <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The register starts from 0x800 is the 16th MAC address register rather
than the first one.
Fixes: cffb13f4d6fb ("stmmac: extend mac addr reg and fix perfect filering")
Signed-off-by: Jisheng Zhang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The commit 8532f613bc78 ("net: stmmac: introduce MSI Interrupt routines
for mac, safety, RX & TX") introduced the converity warnings:-
1. Unused value (UNUSED_VALUE)
assigned_value: Assigning value REQ_IRQ_ERR_MAC to irq_err here,
but that stored value is not used.
2. Unused value (UNUSED_VALUE)
assigned_value: Assigning value REQ_IRQ_ERR_NO to irq_err here,
but that stored value is overwritten before it can used.
3. Unused value (UNUSED_VALUE)
assigned_value: Assigning value REQ_IRQ_ERR_WOL to irq_err here,
but that stored value is not used.
Fixed these by removing the unnecessary value assignments.
Fixes: 8532f613bc78 ("net: stmmac: introduce MSI Interrupt routines for mac, safety, RX & TX")
Signed-off-by: Wong Vee Khee <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
It has been reported that on RTL8106e the link-up interrupt may be
significantly delayed if the user enables ASPM L1. Per default ASPM
is disabled. The change leaves L1 enabled on the PCIe link (thus still
allowing to reach higher package power saving states), but the
NIC won't actively trigger it.
Reported-by: Koba Ko <[email protected]>
Tested-by: Koba Ko <[email protected]>
Signed-off-by: Heiner Kallweit <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add a debugfs interface for dumping ptp information, which
is helpful for debugging.
Signed-off-by: Huazhong Tan <[email protected]>
Signed-off-by: Yufeng Mo <[email protected]>
Signed-off-by: Guangbin Huang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Adds PTP support for HNS3 ethernet driver.
Signed-off-by: Huazhong Tan <[email protected]>
Signed-off-by: Yufeng Mo <[email protected]>
Signed-off-by: Guangbin Huang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When using firmware-assisted PHY firmware image write to flash,
halt the chip before beginning the flash write operation to allow
the running firmware to store the image persistently. Otherwise,
the running firmware will only store the PHY image in local on-chip
RAM, which will be lost after next reset.
Fixes: 4ee339e1e92a ("cxgb4: add support to flash PHY image")
Signed-off-by: Rahul Lakkireddy <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Before writing new PHY firmware to on-chip memory, driver queries
firmware for current running PHY firmware version, which can result
in sleep waiting for reply. So, move spinlock closer to the actual
on-chip memory write operation, instead of taking it at the callers.
Fixes: 5fff701c838e ("cxgb4: always sync access when flashing PHY firmware")
Signed-off-by: Rahul Lakkireddy <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Boot images are copied to memory and updated with current underlying
device ID before flashing them to adapter. Ensure the updated images
are always flashed in Big Endian to allow the firmware to read the
new images during boot properly.
Fixes: 550883558f17 ("cxgb4: add support to flash boot image")
Signed-off-by: Rahul Lakkireddy <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: ab69bde6b2e9 ("alx: add a simple AR816x/AR817x device driver")
Signed-off-by: Christophe JAILLET <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add support for enabling Tx timestamp requests for outgoing packets on
E810 devices.
The ice hardware can support multiple outstanding Tx timestamp requests.
When sending a descriptor to hardware, a Tx timestamp request is made by
setting a request bit, and assigning an index that represents which Tx
timestamp index to store the timestamp in.
Hardware makes no effort to synchronize the index use, so it is up to
software to ensure that Tx timestamp indexes are not re-used before the
timestamp is reported back.
To do this, introduce a Tx timestamp tracker which will keep track of
currently in-use indexes.
In the hot path, if a packet has a timestamp request, an index will be
requested from the tracker. Unfortunately, this does require a lock as
the indexes are shared across all queues on a PHY. There are not enough
indexes to reliably assign only 1 to each queue.
For the E810 devices, the timestamp indexes are not shared across PHYs,
so each port can have its own tracking.
Once hardware captures a timestamp, an interrupt is fired. In this
interrupt, trigger a new work item that will figure out which timestamp
was completed, and report the timestamp back to the stack.
This function loops through the Tx timestamp indexes and checks whether
there is now a valid timestamp. If so, it clears the PHY timestamp
indication in the PHY memory, locks and removes the SKB and bit in the
tracker, then reports the timestamp to the stack.
It is possible in some cases that a timestamp request will be initiated
but never completed. This might occur if the packet is dropped by
software or hardware before it reaches the PHY.
Add a task to the periodic work function that will check whether
a timestamp request is more than a few seconds old. If so, the timestamp
index is cleared in the PHY, and the SKB is released.
Just as with Rx timestamps, the Tx timestamps are only 40 bits wide, and
use the same overall logic for extending to 64 bits of nanoseconds.
With this change, E810 devices should be able to perform basic PTP
functionality.
Future changes will extend the support to cover the E822-based devices.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Add SIOCGHWTSTAMP and SIOCSHWTSTAMP ioctl handlers to respond to
requests to enable timestamping support. If the request is for enabling
Rx timestamps, set a bit in the Rx descriptors to indicate that receive
timestamps should be reported.
Hardware captures receive timestamps in the PHY which only captures part
of the timer, and reports only 40 bits into the Rx descriptor. The upper
32 bits represent the contents of GLTSYN_TIME_L at the point of packet
reception, while the lower 8 bits represent the upper 8 bits of
GLTSYN_TIME_0.
The networking and PTP stack expect 64 bit timestamps in nanoseconds. To
support this, implement some logic to extend the timestamps by using the
full PHC time.
If the Rx timestamp was captured prior to the PHC time, then the real
timestamp is
PHC - (lower_32_bits(PHC) - timestamp)
If the Rx timestamp was captured after the PHC time, then the real
timestamp is
PHC + (timestamp - lower_32_bits(PHC))
These calculations are correct as long as neither the PHC timestamp nor
the Rx timestamps are more than 2^32-1 nanseconds old. Further, we can
detect when the Rx timestamp is before or after the PHC as long as the
PHC timestamp is no more than 2^31-1 nanoseconds old.
In that case, we calculate the delta between the lower 32 bits of the
PHC and the Rx timestamp. If it's larger than 2^31-1 then the Rx
timestamp must have been captured in the past. If it's smaller, then the
Rx timestamp must have been captured after PHC time.
Add an ice_ptp_extend_32b_ts function that relies on a cached copy of
the PHC time and implements this algorithm to calculate the proper upper
32bits of the Rx timestamps.
Cache the PHC time periodically in all of the Rx rings. This enables
each Rx ring to simply call the extension function with a recent copy of
the PHC time. By ensuring that the PHC time is kept up to date
periodically, we ensure this algorithm doesn't use stale data and
produce incorrect results.
To cache the time, introduce a kworker and a kwork item to periodically
store the Rx time. It might seem like we should use the .do_aux_work
interface of the PTP clock. This doesn't work because all PFs must cache
this time, but only one PF owns the PTP clock device.
Thus, the ice driver will manage its own kthread instead of relying on
the PTP do_aux_work handler.
With this change, the driver can now report Rx timestamps on all
incoming packets.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Now that the driver registers a PTP clock device that represents the
clock hardware, it is important that the clock index is reported via the
ethtool .get_ts_info callback.
The underlying hardware resource is shared between multiple PF
functions. Only one function owns the hardware resources associated with
a timer, but multiple functions may be associated with it for the
purposes of timestamping.
To support this, the owning PF will store the clock index into the
driver shared parameters buffer in firmware. Other PFs will look up the
clock index by reading the driver shared parameter on demand when
requested via the .get_ts_info ethtool function.
In this way, all functions which are tied to the same timer are able to
report the clock index. Userspace software such as ptp4l performs
a look up on the netdev to determine the associated clock, and all
commands to control or configure the clock will be handled through the
controlling PF.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Add a new ice_ptp.c file for holding the basic PTP clock interface
functions. If the device supports PTP, call the new ice_ptp_init and
ice_ptp_release functions where appropriate.
If the function owns the hardware resource associated with the PTP
hardware clock, register with the PTP_1588_CLOCK infrastructure to
allocate a new clock object that represents the device hardware clock.
Implement basic functionality for reading and setting the clock time,
performing clock adjustments, and adjusting the clock frequency.
Future changes will introduce functionality for handling related
features including Tx and Rx timestamps.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Add the ice_ptp_hw.c file and some associated definitions to the ice
driver folder. This file contains basic low level definitions for
functions that interact with the device hardware.
For now, only E810-based devices are supported. The ice hardware
supports 2 major variants which have different PHYs with different
procedures necessary for interacting with the device clock.
Because the device captures timestamps in the PHY, each PHY has its own
internal timer. The timers are synchronized in hardware by first
preparing the source timer and the PHY timer shadow registers, and then
issuing a synchronization command. This ensures that both the source
timer and PHY timers are programmed simultaneously. The timers
themselves are all driven from the same oscillator source.
The functions in ice_ptp_hw.c abstract over the differences between how
the PHYs in E810 are programmed vs how the PHYs in E822 devices are
programmed. This series only implements E810 support, but E822 support
will be added in a future change.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Depending on the device configuration, the ice hardware may share the
PTP hardware clock timer between multiple PFs. Each PF is informed by
firmware during initialization of the PTP timer association.
When bringing up PTP, only the PFs which own the timer shall allocate
a PTP hardware clock. Other PFs associated with that timer must report
the correct PTP clock index in order to allow userspace software the
ability to know which ports are connected to the same clock.
To support this, the firmware has driver shared parameters. These
parameters enable one PF to write the clock index into firmware, and
have other PFs read the associated value out. This enables the driver to
have only a single PF allocate and control the device timer registers,
while other PFs associated with that timer can report the correct clock
in the ETHTOOL_GET_TS_INFO report.
Add support for the necessary admin queue commands to enable reading and
writing of the driver shared parameters. This will be used in a future
change to enable sharing the PTP clock index between PF drivers.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The device firmware reports PTP clock capabilities to each PF during
initialization. This includes various information for both the overall
device and the individual function, including
For functions:
* whether this function has timesync enabled
* whether this function owns one of the 2 possible clock timers, and
which one
* which timer the function is associated with
* the clock frequency, if the device supports multiple clock frequencies
* The GPIO pin association for the timer owned by this PF, if any
For the device:
* Which PF owns timer 0, if any
* Which PF owns timer 1, if any
* whether timer 0 is enabled
* whether timer 1 is enabled
Extract the bits from the capabilities information reported by firmware
and store them in the device and function capability structures.o
This information will be used in a future change to have the function
driver enable PTP hardware clock support.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
In order to support certain device features, including enabling the PTP
hardware clock, the ice driver needs to control some registers on the
device PHY.
These registers are accessed by sending sideband messages. For some
hardware, these messages must be sent over the device admin queue, while
other hardware has a dedicated control queue for the sideband messages.
Add the neighbor device message structure for sending a message to the
neighboring device. Where supported, initialize the sideband control
queue and handle cleanup.
Add a wrapper function for sending sideband control queue messages that
read or write a neighboring device register.
Because some devices send sideband messages over the AdminQ, also
increase the length of the admin queue to allow more messages to be
queued up. This is important because the sideband messages add
additional pressure on the AQ usage.
This support will be used in following patches to enable support for
CONFIG_1588_PTP_CLOCK.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Allow the device to be initialized at a later time if
it is not available at boot. The device will be allowed to probe but
will be given a "down" state. After completing device probe and
registering the net device, the driver will await an interrupt signal
from its partner device, indicating that it is ready for boot. The
driver will schedule a work event to perform the necessary procedure
and begin operation.
Co-developed-by: Thomas Falcon <[email protected]>
Signed-off-by: Thomas Falcon <[email protected]>
Signed-off-by: Cristobal Forno <[email protected]>
Acked-by: Lijun Pan <[email protected]>
Reviewed-by: Dany Madden <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The following features are supported:
- LAG basic operations
- create/delete LAG
- add/remove a member to LAG
- enable/disable member in LAG
- LAG Bridge support
- LAG VLAN support
- LAG FDB support
Limitations:
- Only HASH lag tx type is supported
- The Hash parameters are not configurable. They are applied
during the LAG creation stage.
- Enslaving a port to the LAG device that already has an
upper device is not supported.
Co-developed-by: Andrii Savka <[email protected]>
Signed-off-by: Andrii Savka <[email protected]>
Signed-off-by: Serhiy Boiko <[email protected]>
Co-developed-by: Vadym Kochan <[email protected]>
Signed-off-by: Vadym Kochan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Replace prestera_bridge_port_event(...) by
prestera_bridge_port_join(...) and prestera_bridge_port_leave().
It simplifies the code by reading netdev event specific handling only
once in prestera_main.c
Signed-off-by: Vadym Kochan <[email protected]>
CC: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Move handling of PRECHANGEUPPER event from prestera_switchdev to
prestera_main which is responsible for basic netdev events handling
and routing them to related module.
Signed-off-by: Vadym Kochan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Convert list_for_each() to list_for_each_entry() where
applicable. This simplifies the code.
Reported-by: Hulk Robot <[email protected]>
Signed-off-by: Wang Hai <[email protected]>
Acked-by: Lijun Pan <[email protected]>
Reviewed-by: Dany Madden <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The commit 5a5586112b92 ("net: stmmac: support FPE link partner
hand-shaking procedure") introduced the following coverity warning:
"Parse warning (PW.MIXED_ENUM_TYPE)"
"1. mixed_enum_type: enumerated type mixed with another type"
This is due to both "lo_state" and "lp_sate" which their datatype are
enum stmmac_fpe_state type, and being assigned with "FPE_EVENT_UNKNOWN"
which is a macro-defined of 0. Fixed this by assigned both these
variables with the correct enum value.
Fixes: 5a5586112b92 ("net: stmmac: support FPE link partner hand-shaking procedure")
Signed-off-by: Wong Vee Khee <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|