| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The AON_PM_L2 is normally used to trigger and identify the source of a
wake-up event. Since the RX_SYS clock is no longer turned off, we also
have an interrupt being sent to the SYSTEMPORT INTRL_2_0 controller, and
that interrupt remains active up until the magic packet detector is
disabled which happens much later during the driver resumption.
The race happens if we have a CPU that is entering the SYSTEMPORT
INTRL2_0 handler during resume, and another CPU has managed to clear the
wake-up interrupt during bcm_sysport_resume_from_wol(). In that case, we
have the first CPU stuck in the interrupt handler with an interrupt
cause that has been cleared under its feet, and so we keep returning
IRQ_NONE and we never make any progress.
This was not a problem before because we would always turn off the
RX_SYS clock during WoL, so the SYSTEMPORT INTRL2_0 would also be turned
off as well, thus not latching the interrupt.
The fix is to make sure we do not enable either the MPD or
BRCM_TAG_MATCH interrupts since those are redundant with what the
AON_PM_L2 interrupt controller already processes and they would cause
such a race to occur.
Fixes: bb9051a2b230 ("net: systemport: Add support for WAKE_FILTER")
Fixes: 83e82f4c706b ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
After bfcb79fca19d ("PCI/ERR: Run error recovery callbacks for all affected
devices"), AER errors are always cleared by the PCI core and drivers don't
need to do it themselves.
Remove calls to pci_cleanup_aer_uncorrect_error_status() from device
driver error recovery functions.
Signed-off-by: Oza Pawandeep <[email protected]>
[bhelgaas: changelog, remove PCI core changes, remove unused variables]
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
When FW floods the driver with control messages try to exit the cmsg
processing loop every now and then to avoid soft lockups. Cmsg
processing is generally very lightweight so 512 seems like a reasonable
budget, which should not be exceeded under normal conditions.
Fixes: 77ece8d5f196 ("nfp: add control vNIC datapath")
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Tested-by: Pieter Jansen van Vuuren <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-10-02
This series contains updates to ice driver only.
Anirudh expands the use of VSI handles across the rest of the driver,
which includes refactoring the code to correctly use VSI handles. After
a reset, ensure that all configurations for a VSI get re-applied before
moving on to rebuilding the next VSI.
Dave fixed the driver to check the current link state after reset to
ensure that the correct link state of a port is reported. Fixed an
issue where if the driver is unloaded when traffic is in progress,
errors are generated.
Preethi breaks up the IRQ tracker into a software and hardware IRQ
tracker, where the software IRQ tracker tracks only the PF's IRQ
requests and does not play any role in the VF initialization. The
hardware IRQ tracker represents the device's interrupt space and will be
looked up to see if the device has run our of interrupts when a
interrupt has to be allocated in the device for either PF or VF.
Md Fahad adds support for enabling/disabling RSS via ethtool.
Brett aligns the ice_reset_req enum values to the values that the
hardware understands. Also added initial support for dynamic interrupt
moderation in the ice driver.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix a commit 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") regression with the `declance' driver, which caused
the adapter identification message to be split between two lines, e.g.:
declance.c: v0.011 by Linux MIPS DECstation task force
tc6: PMAD-AA
, addr = 08:00:2b:1b:2a:6a, irq = 14
tc6: registered as eth0.
Address that properly, by printing identification with a single call,
making the messages now look like:
declance.c: v0.011 by Linux MIPS DECstation task force
tc6: PMAD-AA, addr = 08:00:2b:1b:2a:6a, irq = 14
tc6: registered as eth0.
Signed-off-by: Maciej W. Rozycki <[email protected]>
Fixes: 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing continuation lines")
Signed-off-by: David S. Miller <[email protected]>
|
|
Add driver support for reading/configuring the 20G link speed via ethtool.
Signed-off-by: Sudarsana Reddy Kalluru <[email protected]>
Signed-off-by: Michal Kalderon <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add driver support for configuring/reading the 20G link speed.
Signed-off-by: Sudarsana Reddy Kalluru <[email protected]>
Signed-off-by: Michal Kalderon <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
During certain heavy network loads TX could time out
with TX ring dump.
TX is sometimes never restarted after reaching
"tx_stop_threshold" because function "fec_enet_tx_queue"
only tests the first queue.
In addition the TX timeout callback function failed to
recover because it also operated only on the first queue.
Signed-off-by: Rickard x Andersson <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
If the driver is unloaded when traffic is in progress, errors are
generated. Fix this by releasing qvectors and NAPI handler on remove.
Signed-off-by: Dave Ertman <[email protected]>
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Currently there is no support for dynamic interrupt moderation. This
patch adds some initial code to support this. The following changes
were made:
1. Currently we are using multiple members to store the interrupt
granularity (itr_gran_25/50/100/200). This is not necessary because
we can query the device to determine what the interrupt granularity
should be set to, done by a new function ice_get_itr_intrl_gran.
2. Added intrl to ice_q_vector structure to support interrupt rate
limiting.
3. Added the function ice_intrl_usecs_to_reg for converting to a value
in usecs that the device understands.
4. Added call to write to the GLINT_RATE register. Disable intrl by
default for now.
5. Changed rx/tx_itr_setting to itr_setting because having both seems
redundant because a ring is either Tx or Rx.
6. Initialize itr_setting for both Tx/Rx rings in ice_vsi_alloc_rings()
Signed-off-by: Brett Creeley <[email protected]>
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Currently the ice_reset_req enum values have to be translated into
a different set of values that the hardware understands for the same
reset types. Avoid this translation by aligning ice_reset_req enum
values to the ones that the hardware understands.
Also add and else if block to check for ICE_RESET_EMPR and put a dev_dbg
message in the else case.
Signed-off-by: Brett Creeley <[email protected]>
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch implements ethtool hook for enabling/disabling
RSS. While disabling RSS, the LUT should be cleared. And
the LUT should be reconfigured while enabling RSS.
Signed-off-by: Md Fahad Iqbal Polash <[email protected]>
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
For the PF driver, when mapping interrupts to queues, we need to request
IRQs from the kernel and we also have to allocate interrupts from
the device.
Similarly, when the VF driver (iavf.ko) initializes, it requests the kernel
IRQs that it needs but it can't directly allocate interrupts in the device.
Instead, it sends a mailbox message to the ice driver, which then allocates
interrupts in the device on the VF driver's behalf.
Currently both these cases end up having to reserve entries in
pf->irq_tracker but irq_tracker itself is sized based on how many vectors
the PF driver needs. Under the right circumstances, the VF driver can fail
to get entries in irq_tracker, which will result in the VF driver failing
probe.
To fix this, sw_irq_tracker and hw_irq_tracker are introduced. The
sw_irq_tracker tracks only the PF's IRQ request and doesn't play any
role in VF init. hw_irq_tracker represents the device's interrupt space.
When interrupts have to be allocated in the device for either PF or VF,
hw_irq_tracker will be looked up to see if the device has run out of
interrupts.
Signed-off-by: Preethi Banala <[email protected]>
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
We are currently replaying the link state of a port after a reset, but
it is possible that the link state of a port can change during the reset
process. So check for the current link state of a port during the rebuild
process of a reset.
Signed-off-by: Dave Ertman <[email protected]>
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Currently, switch filters get replayed after reset. In addition to
filters, other VSI attributes (like RSS configuration, Tx scheduler
configuration, etc.) also need to be replayed after reset.
Thus, instead of replaying based on functional blocks (i.e. replay
all filters for all VSIs, followed by RSS configuration replay for
all VSIs, and so on), it makes more sense to have the replay centered
around a VSI. In other words, replay all configurations for a VSI before
moving on to rebuilding the next VSI.
To that effect, this patch introduces a VSI replay framework in a new
function ice_vsi_replay_all. Currently it only replays switch filters,
but it will be expanded in the future to replay additional VSI attributes.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch is a continuation of the previous patch where VSI
handles are used instead of VSI numbers.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
A VSI handle is just a number the driver maintains to uniquely identify
a VSI. A VSI handle is backed by a VSI number in the hardware. When
interacting when the hardware, VSI handles are converted into VSI numbers.
In commit 0f9d5027a749 ("ice: Refactor VSI allocation, deletion and
rebuild flow"), VSI handles were introduced but it was used only
when creating and deleting VSIs. This patch is part one of two patches
that expands the use of VSI handles across the rest of the driver. Also
in this patch, certain parts of the code had to be refactored to correctly
use VSI handles.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
In current ABI the size of the messages carrying map elements was
statically defined to at most 16 words of key and 16 words of value
(NFP word is 4 bytes). We should not make this assumption and use
the max key and value sizes from the BPF capability instead.
To make sure old kernels don't get surprised with larger (or smaller)
messages bump the FW ABI version to 3 when key/value size is different
than 16 words.
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
Some apps may want to have higher MTU on the control vNIC/queue.
Allow them to set the requested MTU at init time.
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
Up until now we only had per-vNIC BPF ABI version capabilities,
which are slightly awkward to use because bulk of the resources
and configuration does not relate to any particular vNIC. Add
a new capability for global ABI version and check the per-vNIC
version are equal to it. Assume the ABI version 2 if no explicit
version capability is present.
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
When choosing channel amounts and ring sizes, the maximums in the
ibmvnic driver are defined by the virtual i/o server management
partition. Even though they are defined as maximums, the client
driver may in fact successfully request resources that exceed
these limits, which are mostly dependent on a user's hardware
With this in mind, provide an ethtool flag that when enabled will
allow the user to request resources limited by driver-defined
maximums instead of limits defined by the management partition.
The driver will try to honor the user's request but may not allowed
by the management partition. In this case, the driver requests
as close as it can get to the desired amount until it succeeds.
Signed-off-by: Thomas Falcon <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Introduce driver-defined maximums for queue ring sizes. Devices
available for IBM vNIC today will likely not allow this amount,
but this should give us some leeway for future devices that may
support larger ring sizes.
Signed-off-by: Thomas Falcon <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Increase queue size limit to 16. Devices available for IBM vNIC today
will not allow this amount, but this should give us some leeway for
future devices that may support more RX or TX queues.
Signed-off-by: Thomas Falcon <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Some of the chip-specific hw_start functions set bit TXCFG_AUTO_FIFO
in register TxConfig. The original patch changed the order of some
calls resulting in these changes being overwritten by
rtl_set_tx_config_registers() in rtl_hw_start(). This eventually
resulted in network stalls especially under high load.
Analyzing the chip-specific hw_start functions all chip version from
34, with the exception of version 39, need this bit set.
This patch moves setting this bit to rtl_set_tx_config_registers().
Fixes: 4fd48c4ac0a0 ("r8169: move common initializations to tp->hw_start")
Reported-by: Ortwin Glück <[email protected]>
Reported-by: David Arendt <[email protected]>
Root-caused-by: Maciej S. Szmigiero <[email protected]>
Tested-by: Tony Atkinson <[email protected]>
Tested-by: David Arendt <[email protected]>
Tested-by: Ortwin Glück <[email protected]>
Signed-off-by: Heiner Kallweit <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When inserting the TSB, keep track of how many times we had to do it and
if there was a failure in doing so, this helps profile the driver for
possibly incorrect headroom settings.
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
During bcm_sysport_insert_tsb() make sure we differentiate a SKB
headroom re-allocation failure from the normal swap and replace path.
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
We can turn on the RX/TX checksum offloads by default and make sure that
those are properly reflected back to e.g: stacked devices such as VLAN
or DSA.
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
During driver resume and open, the HW may have lost its context/state,
utilize bcm_sysport_set_features() to make sure we do restore the
correct set of features that were previously configured.
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In preparation for unconditionally enabling TX and RX checksum offloads,
refactor bcm_sysport_set_features() a bit such that
__netdev_update_features() during register_netdev() can make sure that
features are correctly programmed during network device registration.
Since we can now be called during register_netdev() with clocks gated,
we need to temporarily turn them on/off in order to have a successful
register programming.
We also move the CRC forward setting read into
bcm_sysport_set_features() since priv->crc_fwd matters while turning on
RX checksum offload, that way we are guaranteed they are in sync in case
we ever add support for NETIF_F_RXFCS at some point in the future.
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds switch for flow director with ethtool command
Signed-off-by: Jian Shen <[email protected]>
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch removes all flow director rules when unload hns3 driver.
Signed-off-by: Jian Shen <[email protected]>
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When doing reset, remove all entries in TCAM block, and keep flow
director rules list. After finishing reset, restore all entries.
Signed-off-by: Jian Shen <[email protected]>
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds support for querying rule number and rule details
by ethtool commands.
Signed-off-by: Jian Shen <[email protected]>
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds support for add and delete rule by ethtool commands.
HNS3 driver supports several flow types, include ETHER_FLOW,
IP_USER_FLOW, TCP_V4_FLOW, UDP_V4_FLOW, SCTP_V4_FLOW, IPV6_USER_FLOW,
TCP_V6_FLOW, UDP_V6_FLOW and SCTP_V6_FLOW.
Signed-off-by: Jian Shen <[email protected]>
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Each flow director rule consists of input key and action. The input key
is the condition for matching, includes tuples of L2/L3/L4 header.
Action is the behaviour when a packet matches with the input key, such
as drop the packet, or forward to a specified queue.
The input key is stored in the tcam blocks, Each bit of input key can
be masked.
Signed-off-by: Jian Shen <[email protected]>
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Flow director is a new feature supported by hardware with revision 0x21.
This patch adds flow direcor initialization for each PF. It queries flow
director mode and tcam resource from firmware, selects tuples used for
input key.
Signed-off-by: Jian Shen <[email protected]>
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This is one step in allowing phylib to make use of link_mode bitmaps,
instead of u32 for supported and advertised features. Convert the phy
drivers to use bitmaps to indicates the features they support.
Build bitmap equivalents of the u32 values at runtime, and have the
drivers point to the appropriate bitmap. These bitmaps are shared, and
we don't want a driver to modify them. So mark them __ro_after_init.
Within phylib, the features bitmap is currently turned back into a
u32. This will be removed once the whole of phylib, and the drivers
are converted to use bitmaps.
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The macro PHY_GBIT_FEAUTRES needs to change into a bitmap in order to
support link_modes. Remove its use from xgde by replacing it with its
definition.
Probably, the current behavior is wrong. It probably should be
ANDing not assigning.
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add a helper to convert the local advertising to an LCL capabilities,
which is then used to resolve pause flow control settings.
Signed-off-by: Andrew Lunn <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Maxime Chevallier <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Reserve two TLV types for feature development, and warn in the driver
if they ever leak into production.
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Address compiler warning reported by kbuild autobuilders
when building for i386 as a result of dma_addr_t size on
different architectures.
warning: cast to pointer from integer of different size
[-Wint-to-pointer-cast]
Fixes: 7e8d5755be0e ("net: nixge: Add support for 64-bit platforms")
Signed-off-by: Moritz Fischer <[email protected]>
Cc: Arnd Bergmann <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-10-01
This series includes updates to mlx5e ethernet netdevice driver:
From Or Gerlitz:
1) Support masks for l3/l4 filters in ethtool flow steering
2) Report checksum unnecessary also when the L3 checksum flag on the
cqe is set and there's no L4 header
3) Allow reporting of checksum unnecessary, using an ethtool private flag.
From Gavi Teitz and Or, VF representors netdevs performance improvements
4) Allow striding RQ in VF representor and bigger RQ size, ~3X performance improvement
5) Enable stateless offloads for VF representor, csum and TSO, 1.5X performance improvement
6) RSS Support for VF representors
6.1) Allow flow table destination fir VF representor steering rule.
6.2) Create RSS flow table per representor netdev
6.3) Expose mlx5e RSS ethtool to be used by representor netdevs
6.4) Enable multi-queue and RSS for VF representors, using mlx5e existing infrastructure
for managing a multi-queue RX RSS tables.
From Alaa Hleihel:
7) Cache the system image guid, The system image guid is a read-only field
Read this once and save it on the core device.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-10-01
This series contains updates to ice driver only.
Anirudh provides several changes to "prep" the driver for upcoming
features. Specifically, the functions that are used for PF VSI/netdev
setup will also be used in SR-IOV support and to allow the reuse of
these functions, code needs to move.
Dave provides the only other change in the series, updates the driver to
protect the reset patch in its entirety. This is done by adding the
various bit checks to determine if a reset is scheduled/initiated and
whether it came from the software or firmware.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Currently, there is no bit, or set of bits, that protect the entirety
of the reset path.
If the reset is originated by the driver, then the relevant
one of the following bits will be set when the reset is scheduled:
__ICE_PFR_REQ
__ICE_CORER_REQ
__ICE_GLOBR_REQ
This bit will not be cleared until after the rebuild has completed.
If the reset is originated by the FW, then the first the driver knows of
it will be the reception of the OICR interrupt. The __ICE_RESET_OICR_RECV
bit will be set in the interrupt handler. This will also be the indicator
in a SW originated reset that we have completed the pre-OICR tasks and
have informed the FW that a reset was requested.
To utilize these bits, change the function:
ice_is_reset_recovery_pending()
to be:
ice_is_reset_in_progress()
The new function will check all of the above bits in the pf->state and
will return a true if one or more of these bits are set.
Signed-off-by: Dave Ertman <[email protected]>
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch completes the code move out of ice_main.c
The following top level functions and related dependency functions) were
moved to ice_lib.c:
ice_vsi_setup
ice_vsi_cfg_tc
The following functions were made static again:
ice_vsi_setup_vector_base
ice_vsi_alloc_q_vectors
ice_vsi_get_qs
void ice_vsi_map_rings_to_vectors
ice_vsi_alloc_rings
ice_vsi_set_rss_params
ice_vsi_set_num_qs
ice_get_free_slot
ice_vsi_init
ice_vsi_alloc_arrays
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch continues the code move out of ice_main.c
The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_setup_vector_base
ice_vsi_alloc_q_vectors
ice_vsi_get_qs
The following functions were made static again:
ice_vsi_free_arrays
ice_vsi_clear_rings
Also, in this patch, the netdev and NAPI registration logic was de-coupled
from the VSI creation logic (ice_vsi_setup) as for SR-IOV, while we want to
create VF VSIs using ice_vsi_setup, we don't want to create netdevs.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch continues the code move out of ice_main.c
The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_clear
ice_vsi_close
ice_vsi_free_arrays
ice_vsi_map_rings_to_vectors
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch continues the code move out of ice_main.c
The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_alloc_rings
ice_vsi_set_rss_params
ice_vsi_set_num_qs
ice_get_free_slot
ice_vsi_init
ice_vsi_clear_rings
ice_vsi_alloc_arrays
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch continues the code move out of ice_main.c
The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_delete
ice_free_res
ice_get_res
ice_is_reset_recovery_pending
ice_vsi_put_qs
ice_vsi_dis_irq
ice_vsi_free_irq
ice_vsi_free_rx_rings
ice_vsi_free_tx_rings
ice_msix_clean_rings
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch continues the code move out of ice_main.c
The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_start_rx_rings
ice_vsi_stop_rx_rings
ice_vsi_stop_tx_rings
ice_vsi_cfg_rxqs
ice_vsi_cfg_txqs
ice_vsi_cfg_msix
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|