| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
napi poll functions should be initialized before running request_irq(),
to handle a rare condition where there is a pending interrupt, causing
the ISR to fire immediately while the poll function wasn't set yet,
causing a NULL dereference.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In a rare scenario when ena_device_restore() fails, followed by device
remove, an FLR will not be issued. In this case, the device will keep
sending asynchronous AENQ keep-alive events, even after driver removal,
leading to memory corruption.
Fixes: 8c5c7abdeb2d ("net: ena: add power management ops to the ENA driver")
Signed-off-by: Arthur Kiyanovski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Memory mapped with devm_ioremap is automatically freed when the driver
is disconnected from the device. Therefore there is no need to
explicitly call devm_iounmap.
Fixes: 0857d92f71b6 ("net: ena: add missing unmap bars on device removal")
Fixes: 411838e7b41c ("net: ena: fix rare kernel crash when bar memory remap fails")
Signed-off-by: Arthur Kiyanovski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-10-08
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) sk_lookup_[tcp|udp] and sk_release helpers from Joe Stringer which allow
BPF programs to perform lookups for sockets in a network namespace. This would
allow programs to determine early on in processing whether the stack is
expecting to receive the packet, and perform some action (eg drop,
forward somewhere) based on this information.
2) per-cpu cgroup local storage from Roman Gushchin.
Per-cpu cgroup local storage is very similar to simple cgroup storage
except all the data is per-cpu. The main goal of per-cpu variant is to
implement super fast counters (e.g. packet counters), which don't require
neither lookups, neither atomic operations in a fast path.
The example of these hybrid counters is in selftests/bpf/netcnt_prog.c
3) allow HW offload of programs with BPF-to-BPF function calls from Quentin Monnet
4) support more than 64-byte key/value in HW offloaded BPF maps from Jakub Kicinski
5) rename of libbpf interfaces from Andrey Ignatov.
libbpf is maturing as a library and should follow good practices in
library design and implementation to play well with other libraries.
This patch set brings consistent naming convention to global symbols.
6) relicense libbpf as LGPL-2.1 OR BSD-2-Clause from Alexei Starovoitov
to let Apache2 projects use libbpf
7) various AF_XDP fixes from Björn and Magnus
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Until now, both Rx and Tx confirmation frames handled during
NAPI poll were counted toward the NAPI budget. However, Tx
confirmations are lighter to process than Rx frames, which can
skew the amount of work actually done inside one NAPI cycle.
Update the code to only count Rx frames toward the NAPI budget
and set a separate threshold on how many Tx conf frames can be
processed in one poll cycle.
The NAPI poll routine stops when either the budget is consumed
by Rx frames or when Tx confirmation frames reach this threshold.
Signed-off-by: Ioana Radulescu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mscc/ocelot_board.c: In function 'mscc_ocelot_probe':
drivers/net/ethernet/mscc/ocelot_board.c:262:17: warning:
variable 'phy_mode' set but not used [-Wunused-but-set-variable]
enum phy_mode phy_mode;
It never used since introduction in
commit 71e32a20cfbf ("net: mscc: ocelot: make use of SerDes PHYs for handling their configuration")
Signed-off-by: YueHaibing <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch is to fix and improve dpaa2-ptp driver
in some places.
- Fixed the return for some functions.
- Replaced kzalloc with devm_kzalloc.
- Removed dev_set_drvdata(dev, NULL).
- Made ptp_dpaa2_caps const.
Signed-off-by: Yangbo Lu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch is to removed unused code for dprtc.
This code will be re-added along with more features
of dpaa2-ptp added.
Signed-off-by: Yangbo Lu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In dpaa2-ptp driver, it's odd to use rtc in names of
some functions and structures except these dprtc APIs.
This patch is to use ptp instead of rtc in names.
Signed-off-by: Yangbo Lu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The NETDEVICES dependency and ETHERNET dependency hadn't
been required since dpaa2-eth was moved out of staging.
Also allowed COMPILE_TEST for dpaa2-eth.
Signed-off-by: Yangbo Lu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch is to move DPAA2 PTP driver out of staging/
since the dpaa2-eth had been moved out.
Signed-off-by: Yangbo Lu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Mark instructions that use pointers to areas in the stack outside of the
current stack frame, and process them accordingly in mem_op_stack().
This way, we also support BPF-to-BPF calls where the caller passes a
pointer to data in its own stack frame to the callee (typically, when
the caller passes an address to one of its local variables located in
the stack, as an argument).
Thanks to Jakub and Jiong for figuring out how to deal with this case,
I just had to turn their email discussion into this patch.
Suggested-by: Jiong Wang <[email protected]>
Suggested-by: Jakub Kicinski <[email protected]>
Signed-off-by: Quentin Monnet <[email protected]>
Reviewed-by: Jiong Wang <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
When pre-processing the instructions, it is trivial to detect what
subprograms are using R6, R7, R8 or R9 as destination registers. If a
subprogram uses none of those, then we do not need to jump to the
subroutines dedicated to saving and restoring callee-saved registers in
its prologue and epilogue.
This patch introduces detection of callee-saved registers in subprograms
and prevents the JIT from adding calls to those subroutines whenever we
can: we save some instructions in the translated program, and some time
at runtime on BPF-to-BPF calls and returns.
If no subprogram needs to save those registers, we can avoid appending
the subroutines at the end of the program.
Signed-off-by: Quentin Monnet <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
On performing a BPF-to-BPF call, we first jump to a subroutine that
pushes callee-saved registers (R6~R9) to the stack, and from there we
goes to the start of the callee next. In order to do so, the caller must
pass to the subroutine the address of the NFP instruction to jump to at
the end of that subroutine. This cannot be reliably implemented when
translated the caller, as we do not always know the start offset of the
callee yet.
This patch implement the required fixup step for passing the start
offset in the callee via the register used by the subroutine to hold its
return address.
Signed-off-by: Quentin Monnet <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
Relocation for targets of BPF-to-BPF calls are required at the end of
translation. Update the nfp_fixup_branches() function in that regard.
When checking that the last instruction of each bloc is a branch, we
must account for the length of the instructions required to pop the
return address from the stack.
Signed-off-by: Quentin Monnet <[email protected]>
Signed-off-by: Jiong Wang <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
Offloaded programs using BPF-to-BPF calls use the stack to store the
return address when calling into a subprogram. Callees also need some
space to save eBPF registers R6 to R9. And contrarily to kernel
verifier, we align stack frames on 64 bytes (and not 32). Account for
all this when checking the stack size limit before JIT-ing the program.
This means we have to recompute maximum stack usage for the program, we
cannot get the value from the kernel.
In addition to adapting the checks on stack usage, move them to the
finalize() callback, now that we have it and because such checks are
part of the verification step rather than translation.
Signed-off-by: Quentin Monnet <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
This is the main patch for the logics of BPF-to-BPF calls in the nfp
driver.
The functions called on BPF_JUMP | BPF_CALL and BPF_JUMP | BPF_EXIT were
used to call helpers and exit from the program, respectively; make them
usable for calling into, or returning from, a BPF subprogram as well.
For all calls, push the return address as well as the callee-saved
registers (R6 to R9) to the stack, and pop them upon returning from the
calls. In order to limit the overhead in terms of instruction number,
this is done through dedicated subroutines. Jumping to the callee
actually consists in jumping to the subroutine, that "returns" to the
callee: this will require some fixup for passing the address in a later
patch. Similarly, returning consists in jumping to the subroutine, which
pops registers and then return directly to the caller (but no fixup is
needed here).
Return to the caller is performed with the RTN instruction newly added
to the JIT.
For the few steps where we need to know what subprogram an instruction
belongs to, the struct nfp_insn_meta is extended with a new subprog_idx
field.
Note that checks on the available stack size, to take into account the
additional requirements associated to BPF-to-BPF calls (storing R6-R9
and return addresses), are added in a later patch.
Signed-off-by: Quentin Monnet <[email protected]>
Signed-off-by: Jiong Wang <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
Similarly to "exit" or "helper call" instructions, BPF-to-BPF calls will
require additional processing before translation starts, in order to
record and mark jump destinations.
We also mark the instructions where each subprogram begins. This will be
used in a following commit to determine where to add prologues for
subprograms.
Signed-off-by: Quentin Monnet <[email protected]>
Reviewed-by: Jiong Wang <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
The checks related to eBPF helper calls are performed each time the nfp
driver meets a BPF_JUMP | BPF_CALL instruction. However, these checks
are not relevant for BPF-to-BPF call (same instruction code, different
value in source register), so just skip the checks for such calls.
While at it, rename the function that runs those checks to make it clear
they apply to _helper_ calls only.
Signed-off-by: Quentin Monnet <[email protected]>
Reviewed-by: Jiong Wang <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
In order to support BPF-to-BPF calls in offloaded programs, the nfp
driver must collect information about the distinct subprograms: namely,
the number of subprograms composing the complete program and the stack
depth of those subprograms. The latter in particular is non-trivial to
collect, so we copy those elements from the kernel verifier via the
newly added post-verification hook. The struct nfp_prog is extended to
store this information. Stack depths are stored in an array of dedicated
structs.
Subprogram start indexes are not collected. Instead, meta instructions
associated to the start of a subprogram will be marked with a flag in a
later patch.
Signed-off-by: Quentin Monnet <[email protected]>
Reviewed-by: Jiong Wang <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
In preparation for support for BPF to BPF calls in offloaded programs,
rename the "stack_depth" field of the struct nfp_prog as
"stack_frame_depth". This is to make it clear that the field refers to
the maximum size of the current stack frame (as opposed to the maximum
size of the whole stack memory).
Signed-off-by: Quentin Monnet <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
In preparation for BPF-to-BPF calls in offloaded programs, add a new
function attribute to the struct bpf_prog_offload_ops so that drivers
supporting eBPF offload can hook at the end of program verification, and
potentially extract information collected by the verifier.
Implement a minimal callback (returning 0) in the drivers providing the
structs, namely netdevsim and nfp.
This will be useful in the nfp driver, in later commits, to extract the
number of subprograms as well as the stack depth for those subprograms.
Signed-off-by: Quentin Monnet <[email protected]>
Reviewed-by: Jiong Wang <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
There is no need to compare *val.vu32* with < 0 because
such variable is of type u32 (32 bits, unsigned), making it
impossible to hold a negative value. Fix this by removing
such comparison.
Also, initialize variable *max_val* to -1, just in case
it is not initialized to either BNXT_MSIX_VEC_MAX or
BNXT_MSIX_VEC_MIN_MAX before using it in a comparison
with val.vu32 at line 159:
if (val.vu32 > max_val)
Addresses-Coverity-ID: 1473915 ("Unsigned compared against 0")
Addresses-Coverity-ID: 1473920 ("Uninitialized scalar variable")
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
|
|
When offloading the L3 and L4 csum computation on TX, we need to extract
the l3_proto from the ethtype, independently of the presence of a vlan
tag.
The actual driver uses skb->protocol as-is, resulting in packets with
the wrong L4 checksum being sent when there's a vlan tag in the packet
header and checksum offloading is enabled.
This commit makes use of vlan_protocol_get() to get the correct ethtype
regardless the presence of a vlan tag.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Maxime Chevallier <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Previously, the SerDes muxing was hardcoded to a given mode in the MAC
controller driver. Now, the SerDes muxing is configured within the
Device Tree and is enforced in the MAC controller driver so we can have
a lot of different SerDes configurations.
Make use of the SerDes PHYs in the MAC controller to set up the SerDes
according to the SerDes<->switch port mapping and the communication mode
with the Ethernet PHY.
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Since HSIO address space can be accessed by different drivers, let's
simplify the register address definitions so that it can be easily used
by all drivers and put the register address definition in the
include/soc/mscc/ocelot_hsio.h header file.
Reviewed-by: Florian Fainelli <[email protected]>
Acked-by: Alexandre Belloni <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Since HSIO address space can be used by different drivers (PLL, SerDes
muxing, temperature sensor), let's move it somewhere it can be included
by all drivers.
Reviewed-by: Florian Fainelli <[email protected]>
Acked-by: Alexandre Belloni <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
HSIO address space was moved to a syscon, hence we need to get the
regmap of this address space from there and no more from the device
node.
Reviewed-by: Florian Fainelli <[email protected]>
Acked-by: Alexandre Belloni <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In revision 0x20, we use vlan id != 0 to check whether a vlan tag
has been offloaded, so vlan id 0 is not supported.
In revision 0x21, rx buffer descriptor adds two bits to indicate
whether one or more vlan tags have been offloaded, so vlan id 0
is valid now.
This patch seperates the handle for vlan id 0, add vlan id 0 support
for revision 0x21.
Fixes: 5b5455a9ed5a ("net: hns3: Add STRP_TAGP field support for hardware revision 0x21")
Signed-off-by: Jian Shen <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In revision 0x21, hw supports both ingress and egress vlan filter.
This patch adds support for it.
Signed-off-by: Zhongzhu Liu <[email protected]>
Signed-off-by: Jian Shen <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
For mta table support has been dropped, remove the code for mta table.
Signed-off-by: Zhongzhu Liu <[email protected]>
Signed-off-by: Jian Shen <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In previously implement for unicast mac vlan table, the space is
shared by all the functions, driver does nothing when the space is
exhausted. This patch preallocates the space of unicast mac vlan
table for each function by software. Each function can only use its
private space and available shared space, avoiding single function
exhausts too much space, and other functions are unable to add
unicast mac address.
Signed-off-by: Jian Shen <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In original codes, the mac vlan table entries are not cleared when
unload hns3 driver. The dirty mac vlan table entries will make the
result of looking up mac vlan table being unexpected.
When doing core reset or global reset, the firmware will clear all
the tables for driver, and driver shouldn't send any commands to
firmware during reset. But when doing function reset, the driver
needs to clear the tables itself.
This patch clears the mac vlan table entries for each client when
unload driver or reset.
Signed-off-by: Jian Shen <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The default mask configuration has been done by firmware, so the driver
doesn't need to do it any more.
Signed-off-by: Zhongzhu Liu <[email protected]>
Signed-off-by: Peng Li <[email protected]>
Signed-off-by: Jian Shen <[email protected]>
Signed-off-by: Salil Mehta <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In cxgb_extension_ioctl(), the command of the ioctl is firstly copied from
the user-space buffer 'useraddr' to 'cmd' and checked through the
switch statement. If the command is not as expected, an error code
EOPNOTSUPP is returned. In the following execution, i.e., the cases of the
switch statement, the whole buffer of 'useraddr' is copied again to a
specific data structure, according to what kind of command is requested.
However, after the second copy, there is no re-check on the newly-copied
command. Given that the buffer 'useraddr' is in the user space, a malicious
user can race to change the command between the two copies. By doing so,
the attacker can supply malicious data to the kernel and cause undefined
behavior.
This patch adds a re-check in each case of the switch statement if there is
a second copy in that case, to re-check whether the command obtained in the
second copy is the same as the one in the first copy. If not, an error code
EINVAL is returned.
Signed-off-by: Wenwen Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
when 32 bit port capability is in use, use FW_PORT_ACTION_L1_CFG32
rather than FW_PORT_ACTION_L1_CFG.
Signed-off-by: Casey Leedom <[email protected]>
Signed-off-by: Ganesh Goudar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
the be2net implementation of .ndo_tunnel_{add,del}() changes the value of
NETIF_F_GSO_UDP_TUNNEL bit in 'features' and 'hw_features', but it forgets
to call netdev_features_change(). Moreover, ethtool setting for that bit
can potentially be reverted after a tunnel is added or removed.
GSO already does software segmentation when 'hw_enc_features' is 0, even
if VXLAN offload is turned on. In addition, commit 096de2f83ebc ("benet:
stricter vxlan offloading check in be_features_check") avoids hardware
segmentation of non-VXLAN tunneled packets, or VXLAN packets having wrong
destination port. So, it's safe to avoid flipping the above feature on
addition/deletion of VXLAN tunnels.
Fixes: 630f4b70567f ("be2net: Export tunnel offloads only when a VxLAN tunnel is created")
Signed-off-by: Davide Caratti <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When getting the max rings supported, get the reduced max_irqs
by the ones used by RDMA.
If the number MSIX is the limiting factor, this bug may cause the
max ring count to be higher than it should be when RDMA driver is
loaded and may result in ring allocation failures.
Fixes: 30f529473ec9 ("bnxt_en: Do not modify max IRQ count after RDMA driver requests/frees IRQs.")
Signed-off-by: Vasundhara Volam <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When the driver probe fails, all the resources that were allocated prior
to the failure must be freed. However, hwrm dma response memory is not
getting freed.
This patch fixes the problem described above.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Duvvuru <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In HWRM_QUEUE_COS2BW_CFG request, enables field should have the bits
set only for the queue ids which are having the valid parameters.
This causes firmware to return error when the TC to hardware CoS queue
mapping is not 1:1 during DCBNL ETS setup.
Fixes: 2e8ef77ee0ff ("bnxt_en: Add TC to hardware QoS queue mapping logic.")
Signed-off-by: Vasundhara Volam <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The enables bit for VNIC was set wrong when calling the HWRM_FUNC_CFG
firmware call to reserve VNICs. This has the effect that the firmware
will keep a large number of VNICs for the PF, and having very few for
VFs. DPDK driver running on the VFs, which requires more VNICs, may not
work properly as a result.
Fixes: 674f50a5b026 ("bnxt_en: Implement new method to reserve rings.")
Signed-off-by: Michael Chan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds following driver-specific permanent mode boolean
parameter.
gre_ver_check - Generic Routing Encapsulation(GRE) version check
will be enabled in the device. If disabled, device skips version
checking for GRE packets.
Cc: Michael Chan <[email protected]>
Signed-off-by: Vasundhara Volam <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds support for following generic permanent mode
devlink parameters. They can be modified using devlink param
commands.
msix_vec_per_pf_max - This param sets the number of MSIX vectors
that the device requests from the host on driver initialization.
This value is set in the device which limits MSIX vectors per PF.
msix_vec_per_pf_min - This param sets the number of minimal MSIX
vectors required for the device initialization. Value 0 indicates
a default value is selected. This value is set in the device which
limits MSIX vectors per PF.
Cc: Michael Chan <[email protected]>
Signed-off-by: Vasundhara Volam <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
HWRM_ERR_CODE_RESOURCE_ACCESS_DENIED
Return proper error code when Firmware returns
HWRM_ERR_CODE_RESOURCE_ACCESS_DENIED for HWRM_NVM_GET/SET_VARIABLE
commands.
Cc: Michael Chan <[email protected]>
Signed-off-by: Vasundhara Volam <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds support for ignore_ari generic permanent mode
devlink parameter. This parameter is disabled by default. It can be
enabled using devlink param commands.
ignore_ari - If enabled, device ignores ARI(Alternate Routing ID)
capability, even when platforms has the support and creates same number
of partitions when platform does not support ARI capability.
Cc: Michael Chan <[email protected]>
Signed-off-by: Vasundhara Volam <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_ll2.c:799:32: warning: implicit
conversion from enumeration type 'enum core_tx_dest' to different
enumeration type 'enum qed_ll2_tx_dest' [-Wenum-conversion]
tx_pkt.tx_dest = p_ll2_conn->tx_dest;
~ ~~~~~~~~~~~~^~~~~~~
1 warning generated.
Fix this by using a switch statement to convert between the enumerated
values since they are not 1 to 1, which matches how the rest of the
driver handles this conversion.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Suggested-by: Tomer Tayar <[email protected]>
Signed-off-by: Nathan Chancellor <[email protected]>
Acked-by: Tomer Tayar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In commit 602b74eda813 ("mlxsw: spectrum_switchdev: Do not leak RIFs
when removing bridge") I handled the case where RIFs created for VLAN
devices were not properly cleaned up when their real device (a bridge)
was removed.
However, I forgot to handle the case of the VLAN device itself being
removed. Do so now when the VLAN device is being unlinked from its real
device.
Fixes: 99f44bb3527b ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Reported-by: Artem Shvorin <[email protected]>
Tested-by: Artem Shvorin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Due to a hardware issue in Spectrum-2, the field event_type of the event
queue element (EQE) has become reserved. It was used to distinguish between
command interface completion events and completion events.
Use queue number to determine event type, as command interface completion
events are always received on EQ0 and mlxsw driver maps completion events
to EQ1.
Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-10-03
mlx5 core driver and ethernet netdev updates, please note there is a small
devlink releated update to allow extack argument to eswitch operations.
From Eli Britstein,
1) devlink: Add extack argument to the eswitch related operations
2) net/mlx5e: E-Switch, return extack messages for failures in the e-switch devlink callbacks
3) net/mlx5e: Add extack messages for TC offload failures
From Eran Ben Elisha,
4) mlx5e: Add counter for aRFS rule insertion failures
From Feras Daoud
5) Fast teardown support for mlx5 device
This change introduces the enhanced version of the "Force teardown" that
allows SW to perform teardown in a faster way without the need to reclaim
all the FW pages.
Fast teardown provides the following advantages:
1- Fix a FW race condition that could cause command timeout
2- Avoid moving to polling mode
3- Close the vport to prevent PCI ACK to be sent without been scatter
to memory
====================
Signed-off-by: David S. Miller <[email protected]>
|