aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
AgeCommit message (Collapse)AuthorFilesLines
2021-10-14mlxsw: thermal: Fix out-of-bounds memory accessesIdo Schimmel1-47/+5
Currently, mlxsw allows cooling states to be set above the maximum cooling state supported by the driver: # cat /sys/class/thermal/thermal_zone2/cdev0/type mlxsw_fan # cat /sys/class/thermal/thermal_zone2/cdev0/max_state 10 # echo 18 > /sys/class/thermal/thermal_zone2/cdev0/cur_state # echo $? 0 This results in out-of-bounds memory accesses when thermal state transition statistics are enabled (CONFIG_THERMAL_STATISTICS=y), as the transition table is accessed with a too large index (state) [1]. According to the thermal maintainer, it is the responsibility of the driver to reject such operations [2]. Therefore, return an error when the state to be set exceeds the maximum cooling state supported by the driver. To avoid dead code, as suggested by the thermal maintainer [3], partially revert commit a421ce088ac8 ("mlxsw: core: Extend cooling device with cooling levels") that tried to interpret these invalid cooling states (above the maximum) in a special way. The cooling levels array is not removed in order to prevent the fans going below 20% PWM, which would cause them to get stuck at 0% PWM. [1] BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x271/0x290 Read of size 4 at addr ffff8881052f7bf8 by task kworker/0:0/5 CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.15.0-rc3-custom-45935-gce1adf704b14 #122 Hardware name: Mellanox Technologies Ltd. "MSN2410-CB2FO"/"SA000874", BIOS 4.6.5 03/08/2016 Workqueue: events_freezable_power_ thermal_zone_device_check Call Trace: dump_stack_lvl+0x8b/0xb3 print_address_description.constprop.0+0x1f/0x140 kasan_report.cold+0x7f/0x11b thermal_cooling_device_stats_update+0x271/0x290 __thermal_cdev_update+0x15e/0x4e0 thermal_cdev_update+0x9f/0xe0 step_wise_throttle+0x770/0xee0 thermal_zone_device_update+0x3f6/0xdf0 process_one_work+0xa42/0x1770 worker_thread+0x62f/0x13e0 kthread+0x3ee/0x4e0 ret_from_fork+0x1f/0x30 Allocated by task 1: kasan_save_stack+0x1b/0x40 __kasan_kmalloc+0x7c/0x90 thermal_cooling_device_setup_sysfs+0x153/0x2c0 __thermal_cooling_device_register.part.0+0x25b/0x9c0 thermal_cooling_device_register+0xb3/0x100 mlxsw_thermal_init+0x5c5/0x7e0 __mlxsw_core_bus_device_register+0xcb3/0x19c0 mlxsw_core_bus_device_register+0x56/0xb0 mlxsw_pci_probe+0x54f/0x710 local_pci_probe+0xc6/0x170 pci_device_probe+0x2b2/0x4d0 really_probe+0x293/0xd10 __driver_probe_device+0x2af/0x440 driver_probe_device+0x51/0x1e0 __driver_attach+0x21b/0x530 bus_for_each_dev+0x14c/0x1d0 bus_add_driver+0x3ac/0x650 driver_register+0x241/0x3d0 mlxsw_sp_module_init+0xa2/0x174 do_one_initcall+0xee/0x5f0 kernel_init_freeable+0x45a/0x4de kernel_init+0x1f/0x210 ret_from_fork+0x1f/0x30 The buggy address belongs to the object at ffff8881052f7800 which belongs to the cache kmalloc-1k of size 1024 The buggy address is located 1016 bytes inside of 1024-byte region [ffff8881052f7800, ffff8881052f7c00) The buggy address belongs to the page: page:0000000052355272 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1052f0 head:0000000052355272 order:3 compound_mapcount:0 compound_pincount:0 flags: 0x200000000010200(slab|head|node=0|zone=2) raw: 0200000000010200 ffffea0005034800 0000000300000003 ffff888100041dc0 raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8881052f7a80: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc ffff8881052f7b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >ffff8881052f7b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff8881052f7c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881052f7c80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [2] https://lore.kernel.org/linux-pm/[email protected]/ [3] https://lore.kernel.org/linux-pm/[email protected]/ CC: Daniel Lezcano <[email protected]> Fixes: a50c1e35650b ("mlxsw: core: Implement thermal zone") Fixes: a421ce088ac8 ("mlxsw: core: Extend cooling device with cooling levels") Signed-off-by: Ido Schimmel <[email protected]> Tested-by: Vadim Pasternak <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-14ethernet: s2io: fix setting mac address during resumeArnd Bergmann1-1/+1
After recent cleanups, gcc started warning about a suspicious memcpy() call during the s2io_io_resume() function: In function '__dev_addr_set', inlined from 'eth_hw_addr_set' at include/linux/etherdevice.h:318:2, inlined from 's2io_set_mac_addr' at drivers/net/ethernet/neterion/s2io.c:5205:2, inlined from 's2io_io_resume' at drivers/net/ethernet/neterion/s2io.c:8569:7: arch/x86/include/asm/string_32.h:182:25: error: '__builtin_memcpy' accessing 6 bytes at offsets 0 and 2 overlaps 4 bytes at offset 2 [-Werror=restrict] 182 | #define memcpy(t, f, n) __builtin_memcpy(t, f, n) | ^~~~~~~~~~~~~~~~~~~~~~~~~ include/linux/netdevice.h:4648:9: note: in expansion of macro 'memcpy' 4648 | memcpy(dev->dev_addr, addr, len); | ^~~~~~ What apparently happened is that an old cleanup changed the calling conventions for s2io_set_mac_addr() from taking an ethernet address as a character array to taking a struct sockaddr, but one of the callers was not changed at the same time. Change it to instead call the low-level do_s2io_prog_unicast() function that still takes the old argument type. Fixes: 2fd376884558 ("S2io: Added support set_mac_address driver entry point") Signed-off-by: Arnd Bergmann <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-13net: encx24j600: check error in devm_regmap_init_encx24j600Nanyong Sun3-5/+14
devm_regmap_init may return error which caused by like out of memory, this will results in null pointer dereference later when reading or writing register: general protection fault in encx24j600_spi_probe KASAN: null-ptr-deref in range [0x0000000000000090-0x0000000000000097] CPU: 0 PID: 286 Comm: spi-encx24j600- Not tainted 5.15.0-rc2-00142-g9978db750e31-dirty #11 9c53a778c1306b1b02359f3c2bbedc0222cba652 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 RIP: 0010:regcache_cache_bypass drivers/base/regmap/regcache.c:540 Code: 54 41 89 f4 55 53 48 89 fb 48 83 ec 08 e8 26 94 a8 fe 48 8d bb a0 00 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 4a 03 00 00 4c 8d ab b0 00 00 00 48 8b ab a0 00 RSP: 0018:ffffc900010476b8 EFLAGS: 00010207 RAX: dffffc0000000000 RBX: fffffffffffffff4 RCX: 0000000000000000 RDX: 0000000000000012 RSI: ffff888002de0000 RDI: 0000000000000094 RBP: ffff888013c9a000 R08: 0000000000000000 R09: fffffbfff3f9cc6a R10: ffffc900010476e8 R11: fffffbfff3f9cc69 R12: 0000000000000001 R13: 000000000000000a R14: ffff888013c9af54 R15: ffff888013c9ad08 FS: 00007ffa984ab580(0000) GS:ffff88801fe00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055a6384136c8 CR3: 000000003bbe6003 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: encx24j600_spi_probe drivers/net/ethernet/microchip/encx24j600.c:459 spi_probe drivers/spi/spi.c:397 really_probe drivers/base/dd.c:517 __driver_probe_device drivers/base/dd.c:751 driver_probe_device drivers/base/dd.c:782 __device_attach_driver drivers/base/dd.c:899 bus_for_each_drv drivers/base/bus.c:427 __device_attach drivers/base/dd.c:971 bus_probe_device drivers/base/bus.c:487 device_add drivers/base/core.c:3364 __spi_add_device drivers/spi/spi.c:599 spi_add_device drivers/spi/spi.c:641 spi_new_device drivers/spi/spi.c:717 new_device_store+0x18c/0x1f1 [spi_stub 4e02719357f1ff33f5a43d00630982840568e85e] dev_attr_store drivers/base/core.c:2074 sysfs_kf_write fs/sysfs/file.c:139 kernfs_fop_write_iter fs/kernfs/file.c:300 new_sync_write fs/read_write.c:508 (discriminator 4) vfs_write fs/read_write.c:594 ksys_write fs/read_write.c:648 do_syscall_64 arch/x86/entry/common.c:50 entry_SYSCALL_64_after_hwframe arch/x86/entry/entry_64.S:113 Add error check in devm_regmap_init_encx24j600 to avoid this situation. Fixes: 04fbfce7a222 ("net: Microchip encx24j600 driver") Reported-by: Hulk Robot <[email protected]> Signed-off-by: Nanyong Sun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-13Merge tag 'mlx5-fixes-2021-10-12' of ↵Jakub Kicinski4-16/+66
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5 fixes 2021-10-12 * tag 'mlx5-fixes-2021-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux: net/mlx5e: Fix division by 0 in mlx5e_select_queue for representors net/mlx5e: Mutually exclude RX-FCS and RX-port-timestamp net/mlx5e: Switchdev representors are not vlan challenged net/mlx5e: Fix memory leak in mlx5_core_destroy_cq() error path net/mlx5e: Allow only complete TXQs partition in MQPRIO channel mode net/mlx5: Fix cleanup of bridge delayed work ==================== Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-13net: korina: select CRC32Vegard Nossum1-0/+1
Fix the following build/link error by adding a dependency on the CRC32 routines: ld: drivers/net/ethernet/korina.o: in function `korina_multicast_list': korina.c:(.text+0x1af): undefined reference to `crc32_le' Fixes: ef11291bcd5f9 ("Add support the Korina (IDT RC32434) Ethernet MAC") Cc: Arnd Bergmann <[email protected]> Signed-off-by: Vegard Nossum <[email protected]> Acked-by: Florian fainelli <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-13net: arc: select CRC32Vegard Nossum1-0/+1
Fix the following build/link error by adding a dependency on the CRC32 routines: ld: drivers/net/ethernet/arc/emac_main.o: in function `arc_emac_set_rx_mode': emac_main.c:(.text+0xb11): undefined reference to `crc32_le' The crc32_le() call comes through the ether_crc_le() call in arc_emac_set_rx_mode(). [v2: moved the select to ARC_EMAC_CORE; the Makefile is a bit confusing, but the error comes from emac_main.o, which is part of the arc_emac module, which in turn is enabled by CONFIG_ARC_EMAC_CORE. Note that arc_emac is different from emac_arc...] Fixes: 775dd682e2b0ec ("arc_emac: implement promiscuous mode and multicast filtering") Cc: Arnd Bergmann <[email protected]> Signed-off-by: Vegard Nossum <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-12net: dsa: tag_ocelot: break circular dependency with ocelot switch lib driverVladimir Oltean2-17/+1
As explained here: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/ DSA tagging protocol drivers cannot depend on symbols exported by switch drivers, because this creates a circular dependency that breaks module autoloading. The tag_ocelot.c file depends on the ocelot_ptp_rew_op() function exported by the common ocelot switch lib. This function looks at OCELOT_SKB_CB(skb) and computes how to populate the REW_OP field of the DSA tag, for PTP timestamping (the command: one-step/two-step, and the TX timestamp identifier). None of that requires deep insight into the driver, it is quite stateless, as it only depends upon the skb->cb. So let's make it a static inline function and put it in include/linux/dsa/ocelot.h, a file that despite its name is used by the ocelot switch driver for populating the injection header too - since commit 40d3f295b5fe ("net: mscc: ocelot: use common tag parsing code with DSA"). With that function declared as static inline, its body is expanded inside each call site, so the dependency is broken and the DSA tagger can be built without the switch library, upon which the felix driver depends. Fixes: 39e5308b3250 ("net: mscc: ocelot: support PTP Sync one-step timestamping") Signed-off-by: Vladimir Oltean <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-12net: mscc: ocelot: cross-check the sequence id from the timestamp FIFO with ↵Vladimir Oltean1-1/+23
the skb PTP header The sad reality is that when a PTP frame with a TX timestamping request is transmitted, it isn't guaranteed that it will make it all the way to the wire (due to congestion inside the switch), and that a timestamp will be taken by the hardware and placed in the timestamp FIFO where an IRQ will be raised for it. The implication is that if enough PTP frames are silently dropped by the hardware such that the timestamp ID has rolled over, it is possible to match a timestamp to an old skb. Furthermore, nobody will match on the real skb corresponding to this timestamp, since we stupidly matched on a previous one that was stale in the queue, and stopped there. So PTP timestamping will be broken and there will be no way to recover. It looks like the hardware parses the sequenceID from the PTP header, and also provides that metadata for each timestamp. The driver currently ignores this, but it shouldn't. As an extra resiliency measure, do the following: - check whether the PTP sequenceID also matches between the skb and the timestamp, treat the skb as stale otherwise and free it - if we see a stale skb, don't stop there and try to match an skb one more time, chances are there's one more skb in the queue with the same timestamp ID, otherwise we wouldn't have ever found the stale one (it is by timestamp ID that we matched it). While this does not prevent PTP packet drops, it at least prevents the catastrophic consequences of incorrect timestamp matching. Since we already call ptp_classify_raw in the TX path, save the result in the skb->cb of the clone, and just use that result in the interrupt code path. Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-12net: mscc: ocelot: deny TX timestamping of non-PTP packetsVladimir Oltean1-7/+12
It appears that Ocelot switches cannot timestamp non-PTP frames, I tested this using the isochron program at: https://github.com/vladimiroltean/tsn-scripts with the result that the driver increments the ocelot_port->ts_id counter as expected, puts it in the REW_OP, but the hardware seems to not timestamp these packets at all, since no IRQ is emitted. Therefore check whether we are sending PTP frames, and refuse to populate REW_OP otherwise. Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-12net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skbVladimir Oltean1-3/+3
When skb_match is NULL, it means we received a PTP IRQ for a timestamp ID that the kernel has no idea about, since there is no skb in the timestamping queue with that timestamp ID. This is a grave error and not something to just "continue" over. So print a big warning in case this happens. Also, move the check above ocelot_get_hwtimestamp(), there is no point in reading the full 64-bit current PTP time if we're not going to do anything with it anyway for this skb. Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support") Signed-off-by: Vladimir Oltean <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-12net: mscc: ocelot: avoid overflowing the PTP timestamp FIFOVladimir Oltean1-7/+30
PTP packets with 2-step TX timestamp requests are matched to packets based on the egress port number and a 6-bit timestamp identifier. All PTP timestamps are held in a common FIFO that is 128 entry deep. This patch ensures that back-to-back timestamping requests cannot exceed the hardware FIFO capacity. If that happens, simply send the packets without requesting a TX timestamp to be taken (in the case of felix, since the DSA API has a void return code in ds->ops->port_txtstamp) or drop them (in the case of ocelot). I've moved the ts_id_lock from a per-port basis to a per-switch basis, because we need separate accounting for both numbers of PTP frames in flight. And since we need locking to inc/dec the per-switch counter, that also offers protection for the per-port counter and hence there is no reason to have a per-port counter anymore. Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-12net: mscc: ocelot: make use of all 63 PTP timestamp identifiersVladimir Oltean1-1/+3
At present, there is a problem when user space bombards a port with PTP event frames which have TX timestamping requests (or when a tc-taprio offload is installed on a port, which delays the TX timestamps by a significant amount of time). The driver will happily roll over the 2-bit timestamp ID and this will cause incorrect matches between an skb and the TX timestamp collected from the FIFO. The Ocelot switches have a 6-bit PTP timestamp identifier, and the value 63 is reserved, so that leaves identifiers 0-62 to be used. The timestamp identifiers are selected by the REW_OP packet field, and are actually shared between CPU-injected frames and frames which match a VCAP IS2 rule that modifies the REW_OP. The hardware supports partitioning between the two uses of the REW_OP field through the PTP_ID_LOW and PTP_ID_HIGH registers, and by default reserves the PTP IDs 0-3 for CPU-injected traffic and the rest for VCAP IS2. The driver does not use VCAP IS2 to set REW_OP for 2-step timestamping, and it also writes 0xffffffff to both PTP_ID_HIGH and PTP_ID_LOW in ocelot_init_timestamp() which makes all timestamp identifiers available to CPU injection. Therefore, we can make use of all 63 timestamp identifiers, which should allow more timestampable packets to be in flight on each port. This is only part of the solution, more issues will be addressed in future changes. Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-12nfp: flow_offload: move flow_indr_dev_register from app init to app startBaowen Zheng1-5/+14
In commit 74fc4f828769 ("net: Fix offloading indirect devices dependency on qdisc order creation"), it adds a process to trigger the callback to setup the bo callback when the driver regists a callback. In our current implement, we are not ready to run the callback when nfp call the function flow_indr_dev_register, then there will be error message as: kernel: Oops: 0000 [#1] SMP PTI kernel: CPU: 0 PID: 14119 Comm: kworker/0:0 Tainted: G kernel: Workqueue: events work_for_cpu_fn kernel: RIP: 0010:nfp_flower_indr_setup_tc_cb+0x258/0x410 kernel: RSP: 0018:ffffbc1e02c57bf8 EFLAGS: 00010286 kernel: RAX: 0000000000000000 RBX: ffff9c761fabc000 RCX: 0000000000000001 kernel: RDX: 0000000000000001 RSI: fffffffffffffff0 RDI: ffffffffc0be9ef1 kernel: RBP: ffffbc1e02c57c58 R08: ffffffffc08f33aa R09: ffff9c6db7478800 kernel: R10: 0000009c003f6e00 R11: ffffbc1e02800000 R12: ffffbc1e000d9000 kernel: R13: ffffbc1e000db428 R14: ffff9c6db7478800 R15: ffff9c761e884e80 kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 kernel: CR2: fffffffffffffff0 CR3: 00000009e260a004 CR4: 00000000007706f0 kernel: DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 kernel: DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 kernel: PKRU: 55555554 kernel: Call Trace: kernel: ? flow_indr_dev_register+0xab/0x210 kernel: ? __cond_resched+0x15/0x30 kernel: ? kmem_cache_alloc_trace+0x44/0x4b0 kernel: ? nfp_flower_setup_tc+0x1d0/0x1d0 [nfp] kernel: flow_indr_dev_register+0x158/0x210 kernel: ? tcf_block_unbind+0xe0/0xe0 kernel: nfp_flower_init+0x40b/0x650 [nfp] kernel: nfp_net_pci_probe+0x25f/0x960 [nfp] kernel: ? nfp_rtsym_read_le+0x76/0x130 [nfp] kernel: nfp_pci_probe+0x6a9/0x820 [nfp] kernel: local_pci_probe+0x45/0x80 So we need to call flow_indr_dev_register in app start process instead of init stage. Fixes: 74fc4f828769 ("net: Fix offloading indirect devices dependency on qdisc order creation") Signed-off-by: Baowen Zheng <[email protected]> Signed-off-by: Simon Horman <[email protected]> Signed-off-by: Louis Peens <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-12net/mlx5e: Fix division by 0 in mlx5e_select_queue for representorsMaxim Mikityanskiy1-0/+5
Commit 846d6da1fcdb ("net/mlx5e: Fix division by 0 in mlx5e_select_queue") makes mlx5e_build_nic_params assign a non-zero initial value to priv->num_tc_x_num_ch, so that mlx5e_select_queue doesn't fail with division by 0 if called before the first activation of channels. However, the initialization flow of representors doesn't call mlx5e_build_nic_params, so this bug can still happen with representors. This commit fixes the bug by adding the missing assignment to mlx5e_build_rep_params. Fixes: 846d6da1fcdb ("net/mlx5e: Fix division by 0 in mlx5e_select_queue") Signed-off-by: Maxim Mikityanskiy <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-10-12net/mlx5e: Mutually exclude RX-FCS and RX-port-timestampAya Levin1-5/+52
Due to current HW arch limitations, RX-FCS (scattering FCS frame field to software) and RX-port-timestamp (improved timestamp accuracy on the receive side) can't work together. RX-port-timestamp is not controlled by the user and it is enabled by default when supported by the HW/FW. This patch sets RX-port-timestamp opposite to RX-FCS configuration. Fixes: 102722fc6832 ("net/mlx5e: Add support for RXFCS feature flag") Signed-off-by: Aya Levin <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Reviewed-by: Moshe Shemesh <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-10-12net/mlx5e: Switchdev representors are not vlan challengedSaeed Mahameed1-1/+0
Before this patch, mlx5 representors advertised the NETIF_F_VLAN_CHALLENGED bit, this could lead to missing features when using reps with vxlan/bridge and maybe other virtual interfaces, when such interfaces inherit this bit and block vlan usage in their topology. Example: $ip link add dev bridge type bridge # add representor interface to the bridge $ip link set dev pf0hpf master $ip link add link bridge name vlan10 type vlan id 10 protocol 802.1q Error: 8021q: VLANs not supported on device. Reps are perfectly capable of handling vlan traffic, although they don't implement vlan_{add,kill}_vid ndos, hence, remove NETIF_F_VLAN_CHALLENGED advertisement. Fixes: cb67b832921c ("net/mlx5e: Introduce SRIOV VF representors") Reported-by: Roopa Prabhu <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]> Reviewed-by: Roi Dayan <[email protected]>
2021-10-12net/mlx5e: Fix memory leak in mlx5_core_destroy_cq() error pathValentine Fatiev1-4/+3
Prior to this patch in case mlx5_core_destroy_cq() failed it returns without completing all destroy operations and that leads to memory leak. Instead, complete the destroy flow before return error. Also move mlx5_debug_cq_remove() to the beginning of mlx5_core_destroy_cq() to be symmetrical with mlx5_core_create_cq(). kmemleak complains on: unreferenced object 0xc000000038625100 (size 64): comm "ethtool", pid 28301, jiffies 4298062946 (age 785.380s) hex dump (first 32 bytes): 60 01 48 94 00 00 00 c0 b8 05 34 c3 00 00 00 c0 `.H.......4..... 02 00 00 00 00 00 00 00 00 db 7d c1 00 00 00 c0 ..........}..... backtrace: [<000000009e8643cb>] add_res_tree+0xd0/0x270 [mlx5_core] [<00000000e7cb8e6c>] mlx5_debug_cq_add+0x5c/0xc0 [mlx5_core] [<000000002a12918f>] mlx5_core_create_cq+0x1d0/0x2d0 [mlx5_core] [<00000000cef0a696>] mlx5e_create_cq+0x210/0x3f0 [mlx5_core] [<000000009c642c26>] mlx5e_open_cq+0xb4/0x130 [mlx5_core] [<0000000058dfa578>] mlx5e_ptp_open+0x7f4/0xe10 [mlx5_core] [<0000000081839561>] mlx5e_open_channels+0x9cc/0x13e0 [mlx5_core] [<0000000009cf05d4>] mlx5e_switch_priv_channels+0xa4/0x230 [mlx5_core] [<0000000042bbedd8>] mlx5e_safe_switch_params+0x14c/0x300 [mlx5_core] [<0000000004bc9db8>] set_pflag_tx_port_ts+0x9c/0x160 [mlx5_core] [<00000000a0553443>] mlx5e_set_priv_flags+0xd0/0x1b0 [mlx5_core] [<00000000a8f3d84b>] ethnl_set_privflags+0x234/0x2d0 [<00000000fd27f27c>] genl_family_rcv_msg_doit+0x108/0x1d0 [<00000000f495e2bb>] genl_family_rcv_msg+0xe4/0x1f0 [<00000000646c5c2c>] genl_rcv_msg+0x78/0x120 [<00000000d53e384e>] netlink_rcv_skb+0x74/0x1a0 Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by: Valentine Fatiev <[email protected]> Reviewed-by: Moshe Shemesh <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-10-12net/mlx5e: Allow only complete TXQs partition in MQPRIO channel modeTariq Toukan1-2/+2
Do not allow configurations of MQPRIO channel mode that do not fully define and utilize the channels txqs. Fixes: ec60c4581bd9 ("net/mlx5e: Support MQPRIO channel mode") Signed-off-by: Tariq Toukan <[email protected]> Reviewed-by: Maxim Mikityanskiy <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-10-12net/mlx5: Fix cleanup of bridge delayed workShay Drory1-4/+4
Currently, bridge cleanup is calling to cancel_delayed_work(). When this function is finished, there is a chance that the delayed work is still running. Also, the delayed work is queueing itself. As a result, we might execute the delayed work after the bridge cleanup have finished and hit a null-ptr oops[1]. Fix it by using cancel_delayed_work_sync(), which is waiting until the work is done and will cancel the queue work. [1] [ 8202.143043 ] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 8202.144438 ] #PF: supervisor write access in kernel mode [ 8202.145476 ] #PF: error_code(0x0002) - not-present page [ 8202.146520 ] PGD 0 P4D 0 [ 8202.147126 ] Oops: 0002 [#1] SMP NOPTI [ 8202.147899 ] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.14.0-rc6_for_upstream_min_debug_2021_08_25_16_06 #1 [ 8202.149741 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [ 8202.151908 ] RIP: 0010:_raw_spin_lock+0xc/0x20 [ 8202.156234 ] RSP: 0018:ffff88846f885ea0 EFLAGS: 00010046 [ 8202.157289 ] RAX: 0000000000000000 RBX: ffff88846f880000 RCX: 0000000000000000 [ 8202.158731 ] RDX: 0000000000000001 RSI: ffff8881004000c8 RDI: 0000000000000000 [ 8202.160177 ] RBP: ffff8881fe684978 R08: ffff888100140000 R09: ffffffff824455b8 [ 8202.161569 ] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000001 [ 8202.163004 ] R13: 0000000000000012 R14: 0000000000000200 R15: ffff88812992d000 [ 8202.164018 ] FS: 0000000000000000(0000) GS:ffff88846f880000(0000) knlGS:0000000000000000 [ 8202.164960 ] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 8202.165634 ] CR2: 0000000000000000 CR3: 0000000108cac004 CR4: 0000000000370ea0 [ 8202.166450 ] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 8202.167807 ] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 8202.168852 ] Call Trace: [ 8202.169421 ] <IRQ> [ 8202.169792 ] __queue_work+0xf2/0x3d0 [ 8202.170481 ] ? queue_work_node+0x40/0x40 [ 8202.171270 ] call_timer_fn+0x2b/0x100 [ 8202.171932 ] __run_timers.part.0+0x152/0x220 [ 8202.172717 ] ? __hrtimer_run_queues+0x171/0x290 [ 8202.173526 ] ? kvm_clock_get_cycles+0xd/0x10 [ 8202.174232 ] ? ktime_get+0x35/0x90 [ 8202.174943 ] run_timer_softirq+0x26/0x50 [ 8202.175745 ] __do_softirq+0xc7/0x271 [ 8202.176373 ] irq_exit_rcu+0x93/0xb0 [ 8202.176983 ] sysvec_apic_timer_interrupt+0x72/0x90 [ 8202.177755 ] </IRQ> [ 8202.178245 ] asm_sysvec_apic_timer_interrupt+0x12/0x20 Fixes: c636a0f0f3f0 ("net/mlx5: Bridge, dynamic entry ageing") Signed-off-by: Shay Drory <[email protected]> Reviewed-by: Vlad Buslov <[email protected]> Reviewed-by: Leon Romanovsky <[email protected]> Reviewed-by: Maor Gottlieb <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-10-12ice: fix locking for Tx timestamp tracking flushJacob Keller1-8/+7
Commit 4dd0d5c33c3e ("ice: add lock around Tx timestamp tracker flush") added a lock around the Tx timestamp tracker flow which is used to cleanup any left over SKBs and prepare for device removal. This lock is problematic because it is being held around a call to ice_clear_phy_tstamp. The clear function takes a mutex to send a PHY write command to firmware. This could lead to a deadlock if the mutex actually sleeps, and causes the following warning on a kernel with preemption debugging enabled: [ 715.419426] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:573 [ 715.427900] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 3100, name: rmmod [ 715.435652] INFO: lockdep is turned off. [ 715.439591] Preemption disabled at: [ 715.439594] [<0000000000000000>] 0x0 [ 715.446678] CPU: 52 PID: 3100 Comm: rmmod Tainted: G W OE 5.15.0-rc4+ #42 bdd7ec3018e725f159ca0d372ce8c2c0e784891c [ 715.458058] Hardware name: Intel Corporation S2600STQ/S2600STQ, BIOS SE5C620.86B.02.01.0010.010620200716 01/06/2020 [ 715.468483] Call Trace: [ 715.470940] dump_stack_lvl+0x6a/0x9a [ 715.474613] ___might_sleep.cold+0x224/0x26a [ 715.478895] __mutex_lock+0xb3/0x1440 [ 715.482569] ? stack_depot_save+0x378/0x500 [ 715.486763] ? ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.494979] ? kfree+0xc1/0x520 [ 715.498128] ? mutex_lock_io_nested+0x12a0/0x12a0 [ 715.502837] ? kasan_set_free_info+0x20/0x30 [ 715.507110] ? __kasan_slab_free+0x10b/0x140 [ 715.511385] ? slab_free_freelist_hook+0xc7/0x220 [ 715.516092] ? kfree+0xc1/0x520 [ 715.519235] ? ice_deinit_lag+0x16c/0x220 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.527359] ? ice_remove+0x1cf/0x6a0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.535133] ? pci_device_remove+0xab/0x1d0 [ 715.539318] ? __device_release_driver+0x35b/0x690 [ 715.544110] ? driver_detach+0x214/0x2f0 [ 715.548035] ? bus_remove_driver+0x11d/0x2f0 [ 715.552309] ? pci_unregister_driver+0x26/0x250 [ 715.556840] ? ice_module_exit+0xc/0x2f [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.564799] ? __do_sys_delete_module.constprop.0+0x2d8/0x4e0 [ 715.570554] ? do_syscall_64+0x3b/0x90 [ 715.574303] ? entry_SYSCALL_64_after_hwframe+0x44/0xae [ 715.579529] ? start_flush_work+0x542/0x8f0 [ 715.583719] ? ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.591923] ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.599960] ? wait_for_completion_io+0x250/0x250 [ 715.604662] ? lock_acquire+0x196/0x200 [ 715.608504] ? do_raw_spin_trylock+0xa5/0x160 [ 715.612864] ice_sbq_rw_reg+0x1e6/0x2f0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.620813] ? ice_reset+0x130/0x130 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.628497] ? __debug_check_no_obj_freed+0x1e8/0x3c0 [ 715.633550] ? trace_hardirqs_on+0x1c/0x130 [ 715.637748] ice_write_phy_reg_e810+0x70/0xf0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.646220] ? do_raw_spin_trylock+0xa5/0x160 [ 715.650581] ? ice_ptp_release+0x910/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.658797] ? ice_ptp_release+0x255/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.667013] ice_clear_phy_tstamp+0x2c/0x110 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.675403] ice_ptp_release+0x408/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.683440] ice_remove+0x560/0x6a0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.691037] ? _raw_spin_unlock_irqrestore+0x46/0x73 [ 715.696005] pci_device_remove+0xab/0x1d0 [ 715.700018] __device_release_driver+0x35b/0x690 [ 715.704637] driver_detach+0x214/0x2f0 [ 715.708389] bus_remove_driver+0x11d/0x2f0 [ 715.712489] pci_unregister_driver+0x26/0x250 [ 715.716857] ice_module_exit+0xc/0x2f [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.724637] __do_sys_delete_module.constprop.0+0x2d8/0x4e0 [ 715.730210] ? free_module+0x6d0/0x6d0 [ 715.733963] ? task_work_run+0xe1/0x170 [ 715.737803] ? exit_to_user_mode_loop+0x17f/0x1d0 [ 715.742509] ? rcu_read_lock_sched_held+0x12/0x80 [ 715.747215] ? trace_hardirqs_on+0x1c/0x130 [ 715.751401] do_syscall_64+0x3b/0x90 [ 715.754981] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 715.760033] RIP: 0033:0x7f4dfe59000b [ 715.763612] Code: 73 01 c3 48 8b 0d 6d 1e 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 3d 1e 0c 00 f7 d8 64 89 01 48 [ 715.782357] RSP: 002b:00007ffe8c891708 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0 [ 715.789923] RAX: ffffffffffffffda RBX: 00005558a20468b0 RCX: 00007f4dfe59000b [ 715.797054] RDX: 000000000000000a RSI: 0000000000000800 RDI: 00005558a2046918 [ 715.804189] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 [ 715.811319] R10: 00007f4dfe603ac0 R11: 0000000000000206 R12: 00007ffe8c891940 [ 715.818455] R13: 00007ffe8c8920a3 R14: 00005558a20462a0 R15: 00005558a20468b0 Notice that this is the only case where we use the lock in this way. In the cleanup kthread and work kthread the lock is only taken around the bit accesses. This was done intentionally to avoid this kind of issue. The way the lock is used, we only protect ordering of bit sets vs bit clears. The Tx writers in the hot path don't need to be protected against the entire kthread loop. The Tx queues threads only need to ensure that they do not re-use an index that is currently in use. The cleanup loop does not need to block all new set bits, since it will re-queue itself if new timestamps are present. Fix the tracker flow so that it uses the same flow as the standard cleanup thread. In addition, ensure the in_use bitmap actually gets cleared properly. This fixes the warning and also avoids the potential deadlock that might have occurred otherwise. Fixes: 4dd0d5c33c3e ("ice: add lock around Tx timestamp tracker flush") Signed-off-by: Jacob Keller <[email protected]> Signed-off-by: Tony Nguyen <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-12net: mscc: ocelot: Fix dumplicated argument in ocelotWan Jiabing2-3/+3
Fix the following coccicheck warning: drivers/net/ethernet/mscc/ocelot.c:474:duplicated argument to & or | drivers/net/ethernet/mscc/ocelot.c:476:duplicated argument to & or | drivers/net/ethernet/mscc/ocelot_net.c:1627:duplicated argument to & or | These DEV_CLOCK_CFG_MAC_TX_RST are duplicate here. Here should be DEV_CLOCK_CFG_MAC_RX_RST. Fixes: e6e12df625f2 ("net: mscc: ocelot: convert to phylink") Signed-off-by: Wan Jiabing <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-09qed: Fix missing error code in qed_slowpath_start()chongjiapeng1-0/+1
The error code is missing in this code scenario, add the error code '-EINVAL' to the return value 'rc'. Eliminate the follow smatch warning: drivers/net/ethernet/qlogic/qed/qed_main.c:1298 qed_slowpath_start() warn: missing error code 'rc'. Reported-by: Abaci Robot <[email protected]> Fixes: d51e4af5c209 ("qed: aRFS infrastructure support") Signed-off-by: chongjiapeng <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-09ionic: don't remove netdev->dev_addr when syncing uc listShannon Nelson1-0/+4
Bridging, and possibly other upper stack gizmos, adds the lower device's netdev->dev_addr to its own uc list, and then requests it be deleted when the upper bridge device is removed. This delete request also happens with the bridging vlan_filtering is enabled and then disabled. Bonding has a similar behavior with the uc list, but since it also uses set_mac to manage netdev->dev_addr, it doesn't have the same the failure case. Because we store our netdev->dev_addr in our uc list, we need to ignore the delete request from dev_uc_sync so as to not lose the address and all hope of communicating. Note that ndo_set_mac_address is expressly changing netdev->dev_addr, so no limitation is set there. Fixes: 2a654540be10 ("ionic: Add Rx filter and rx_mode ndo support") Signed-off-by: Shannon Nelson <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-08net: mana: Fix error handling in mana_create_rxq()Haiyang Zhang1-1/+3
Fix error handling in mana_create_rxq() when cq->gdma_id >= gc->max_num_cqs. Fixes: ca9c54d2d6a5 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)") Signed-off-by: Haiyang Zhang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-08net: stmmac: add support for dwmac 3.40aHerve Codina2-0/+9
dwmac 3.40a is an old ip version that can be found on SPEAr3xx soc. Signed-off-by: Herve Codina <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-08net: stmmac: fix get_hw_feature() on old hardwareHerve Codina4-9/+22
Some old IPs do not provide the hardware feature register. On these IPs, this register is read 0x00000000. In old driver version, this feature was handled but a regression came with the commit f10a6a3541b4 ("stmmac: rework get_hw_feature function"). Indeed, this commit removes the return value in dma->get_hw_feature(). This return value was used to indicate the validity of retrieved information and used later on in stmmac_hw_init() to override priv->plat data if this hardware feature were valid. This patch restores the return code in ->get_hw_feature() in order to indicate the hardware feature validity and override priv->plat data only if this hardware feature is valid. Fixes: f10a6a3541b4 ("stmmac: rework get_hw_feature function") Signed-off-by: Herve Codina <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-06iavf: fix double unlock of crit_lockStefan Assmann1-1/+0
The crit_lock mutex could be unlocked twice as reported here https://lists.osuosl.org/pipermail/intel-wired-lan/Week-of-Mon-20210823/025525.html Remove the superfluous unlock. Technically the problem was already present before 5ac49f3c2702 as that commit only replaced the locking primitive, but no functional change. Reported-by: Dan Carpenter <[email protected]> Fixes: 5ac49f3c2702 ("iavf: use mutexes for locking of critical sections") Fixes: bac8486116b0 ("iavf: Refactor the watchdog state machine") Signed-off-by: Stefan Assmann <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
2021-10-06i40e: Fix freeing of uninitialized misc IRQ vectorSylwester Dziedziuch1-1/+2
When VSI set up failed in i40e_probe() as part of PF switch set up driver was trying to free misc IRQ vectors in i40e_clear_interrupt_scheme and produced a kernel Oops: Trying to free already-free IRQ 266 WARNING: CPU: 0 PID: 5 at kernel/irq/manage.c:1731 __free_irq+0x9a/0x300 Workqueue: events work_for_cpu_fn RIP: 0010:__free_irq+0x9a/0x300 Call Trace: ? synchronize_irq+0x3a/0xa0 free_irq+0x2e/0x60 i40e_clear_interrupt_scheme+0x53/0x190 [i40e] i40e_probe.part.108+0x134b/0x1a40 [i40e] ? kmem_cache_alloc+0x158/0x1c0 ? acpi_ut_update_ref_count.part.1+0x8e/0x345 ? acpi_ut_update_object_reference+0x15e/0x1e2 ? strstr+0x21/0x70 ? irq_get_irq_data+0xa/0x20 ? mp_check_pin_attr+0x13/0xc0 ? irq_get_irq_data+0xa/0x20 ? mp_map_pin_to_irq+0xd3/0x2f0 ? acpi_register_gsi_ioapic+0x93/0x170 ? pci_conf1_read+0xa4/0x100 ? pci_bus_read_config_word+0x49/0x70 ? do_pci_enable_device+0xcc/0x100 local_pci_probe+0x41/0x90 work_for_cpu_fn+0x16/0x20 process_one_work+0x1a7/0x360 worker_thread+0x1cf/0x390 ? create_worker+0x1a0/0x1a0 kthread+0x112/0x130 ? kthread_flush_work_fn+0x10/0x10 ret_from_fork+0x1f/0x40 The problem is that at that point misc IRQ vectors were not allocated yet and we get a call trace that driver is trying to free already free IRQ vectors. Add a check in i40e_clear_interrupt_scheme for __I40E_MISC_IRQ_REQUESTED PF state before calling i40e_free_misc_vector. This state is set only if misc IRQ vectors were properly initialized. Fixes: c17401a1dd21 ("i40e: use separate state bit for miscellaneous IRQ setup") Reported-by: PJ Waskiewicz <[email protected]> Signed-off-by: Sylwester Dziedziuch <[email protected]> Signed-off-by: Mateusz Palczewski <[email protected]> Tested-by: Dave Switzer <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
2021-10-06i40e: fix endless loop under rtnlJiri Benc1-1/+1
The loop in i40e_get_capabilities can never end. The problem is that although i40e_aq_discover_capabilities returns with an error if there's a firmware problem, the returned error is not checked. There is a check for pf->hw.aq.asq_last_status but that value is set to I40E_AQ_RC_OK on most firmware problems. When i40e_aq_discover_capabilities encounters a firmware problem, it will encounter the same problem on its next invocation. As the result, the loop becomes endless. We hit this with I40E_ERR_ADMIN_QUEUE_TIMEOUT but looking at the code, it can happen with a range of other firmware errors. I don't know what the correct behavior should be: whether the firmware should be retried a few times, or whether pf->hw.aq.asq_last_status should be always set to the encountered firmware error (but then it would be pointless and can be just replaced by the i40e_aq_discover_capabilities return value). However, the current behavior with an endless loop under the rtnl mutex(!) is unacceptable and Intel has not submitted a fix, although we explained the bug to them 7 months ago. This may not be the best possible fix but it's better than hanging the whole system on a firmware bug. Fixes: 56a62fc86895 ("i40e: init code and hardware support") Tested-by: Stefan Assmann <[email protected]> Signed-off-by: Jiri Benc <[email protected]> Reviewed-by: Jesse Brandeburg <[email protected]> Tested-by: Dave Switzer <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
2021-10-06ionic: move filter sync_needed bit setShannon Nelson2-4/+3
Move the setting of the filter-sync-needed bit to the error case in the filter add routine to be sure we're checking the live filter status rather than a copy of the pre-sync status. Fixes: 969f84394604 ("ionic: sync the filters in the work task") Signed-off-by: Shannon Nelson <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-06gve: report 64bit tx_bytes counter from gve_handle_report_stats()Eric Dumazet1-2/+3
Each tx queue maintains a 64bit counter for bytes, there is no reason to truncate this to 32bit (or this has not been documented) Fixes: 24aeb56f2d38 ("gve: Add Gvnic stats AQ command and ethtool show/set-priv-flags.") Signed-off-by: Eric Dumazet <[email protected]> Cc: Yangchun Fu <[email protected]> Cc: Kuo Zhao <[email protected]> Cc: David Awogbemila <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-06gve: fix gve_get_stats()Eric Dumazet1-4/+9
gve_get_stats() can report wrong numbers if/when u64_stats_fetch_retry() returns true. What is needed here is to sample values in temporary variables, and only use them after each loop is ended. Fixes: f5cedc84a30d ("gve: Add transmit and receive support") Signed-off-by: Eric Dumazet <[email protected]> Cc: Catherine Sullivan <[email protected]> Cc: Sagi Shahar <[email protected]> Cc: Jon Olson <[email protected]> Cc: Willem de Bruijn <[email protected]> Cc: Luigi Rizzo <[email protected]> Cc: Jeroen de Borst <[email protected]> Cc: Tao Liu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-06gve: Properly handle errors in gve_assign_qplCatherine Sullivan1-1/+7
Ignored errors would result in crash. Fixes: ede3fcf5ec67f ("gve: Add support for raw addressing to the rx path") Signed-off-by: Catherine Sullivan <[email protected]> Signed-off-by: Jeroen de Borst <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-06gve: Avoid freeing NULL pointerTao Liu1-10/+17
Prevent possible crashes when cleaning up after unsuccessful initializations. Fixes: 893ce44df5658 ("gve: Add basic driver framework for Compute Engine Virtual NIC") Signed-off-by: Tao Liu <[email protected]> Signed-off-by: Catherine Sully <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-06gve: Correct available tx qpl checkCatherine Sullivan1-1/+1
The qpl_map_size is rounded up to a multiple of sizeof(long), but the number of qpls doesn't have to be. Fixes: f5cedc84a30d2 ("gve: Add transmit and receive support") Signed-off-by: Catherine Sullivan <[email protected]> Signed-off-by: Jeroen de Borst <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-06net: stmmac: trigger PCS EEE to turn off on link downWong Vee Khee1-1/+5
The current implementation enable PCS EEE feature in the event of link up, but PCS EEE feature is not disabled on link down. This patch makes sure PCE EEE feature is disabled on link down. Fixes: 656ed8b015f1 ("net: stmmac: fix EEE init issue when paired with EEE capable PHYs") Signed-off-by: Wong Vee Khee <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-10-01net: stmmac: dwmac-rk: Fix ethernet on rk3399 based devicesPunit Agrawal1-0/+5
Commit 2d26f6e39afb ("net: stmmac: dwmac-rk: fix unbalanced pm_runtime_enable warnings") while getting rid of a runtime PM warning ended up breaking ethernet on rk3399 based devices. By dropping an extra reference to the device, the commit ends up enabling suspend / resume of the ethernet device - which appears to be broken. While the issue with runtime pm is being investigated, partially revert commit 2d26f6e39afb to restore the network on rk3399. Fixes: 2d26f6e39afb ("net: stmmac: dwmac-rk: fix unbalanced pm_runtime_enable warnings") Suggested-by: Heiko Stuebner <[email protected]> Signed-off-by: Punit Agrawal <[email protected]> Cc: Michael Riesch <[email protected]> Tested-by: Heiko Stuebner <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-10-01net: mscc: ocelot: fix VCAP filters remaining active after being deletedVladimir Oltean1-2/+2
When ocelot_flower.c calls ocelot_vcap_filter_add(), the filter has a given filter->id.cookie. This filter is added to the block->rules list. However, when ocelot_flower.c calls ocelot_vcap_block_find_filter_by_id() which passes the cookie as argument, the filter is never found by filter->id.cookie when searching through the block->rules list. This is unsurprising, since the filter->id.cookie is an unsigned long, but the cookie argument provided to ocelot_vcap_block_find_filter_by_id() is a signed int, and the comparison fails. Fixes: 50c6cc5b9283 ("net: mscc: ocelot: store a namespaced VCAP filter ID") Signed-off-by: Vladimir Oltean <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-09-30net/mlx5e: Mutually exclude setting of TX-port-TS and MQPRIO in channel modeAya Levin2-0/+19
TX-port-TS hijacks the PTP traffic to a specific HW TX-queue. This conflicts with MQPRIO in channel mode, which specifies explicitly which TC accepts the packet. This patch mutually excludes the above configuration. Fixes: ec60c4581bd9 ("net/mlx5e: Support MQPRIO channel mode") Signed-off-by: Aya Levin <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-09-30net/mlx5e: Fix the presented RQ index in PTP statsLama Kayal3-3/+5
PTP-RQ counters title format contains PTP-RQ identifier, which is mistakenly not passed to sprinft(). This leads to unexpected garbage values instead. This patch fixes it. Before applying the patch: ethtool -S eth3 | grep ptp_rq ptp_rq15_packets: 0 ptp_rq8_bytes: 0 ptp_rq6_csum_complete: 0 ptp_rq14_csum_complete_tail: 0 ptp_rq3_csum_complete_tail_slow : 0 ptp_rq9_csum_unnecessary: 0 ptp_rq1_csum_unnecessary_inner: 0 ptp_rq7_csum_none: 0 ptp_rq10_xdp_drop: 0 ptp_rq9_xdp_redirect: 0 ptp_rq13_lro_packets: 0 ptp_rq12_lro_bytes: 0 ptp_rq10_ecn_mark: 0 ptp_rq9_removed_vlan_packets: 0 ptp_rq5_wqe_err: 0 ptp_rq8_mpwqe_filler_cqes: 0 ptp_rq2_mpwqe_filler_strides: 0 ptp_rq5_oversize_pkts_sw_drop: 0 ptp_rq6_buff_alloc_err: 0 ptp_rq15_cqe_compress_blks: 0 ptp_rq2_cqe_compress_pkts: 0 ptp_rq2_cache_reuse: 0 ptp_rq12_cache_full: 0 ptp_rq11_cache_empty: 256 ptp_rq12_cache_busy: 0 ptp_rq11_cache_waive: 0 ptp_rq12_congst_umr: 0 ptp_rq11_arfs_err: 0 ptp_rq9_recover: 0 After applying the patch: ethtool -S eth3 | grep ptp_rq ptp_rq0_packets: 0 ptp_rq0_bytes: 0 ptp_rq0_csum_complete: 0 ptp_rq0_csum_complete_tail: 0 ptp_rq0_csum_complete_tail_slow : 0 ptp_rq0_csum_unnecessary: 0 ptp_rq0_csum_unnecessary_inner: 0 ptp_rq0_csum_none: 0 ptp_rq0_xdp_drop: 0 ptp_rq0_xdp_redirect: 0 ptp_rq0_lro_packets: 0 ptp_rq0_lro_bytes: 0 ptp_rq0_ecn_mark: 0 ptp_rq0_removed_vlan_packets: 0 ptp_rq0_wqe_err: 0 ptp_rq0_mpwqe_filler_cqes: 0 ptp_rq0_mpwqe_filler_strides: 0 ptp_rq0_oversize_pkts_sw_drop: 0 ptp_rq0_buff_alloc_err: 0 ptp_rq0_cqe_compress_blks: 0 ptp_rq0_cqe_compress_pkts: 0 ptp_rq0_cache_reuse: 0 ptp_rq0_cache_full: 0 ptp_rq0_cache_empty: 256 ptp_rq0_cache_busy: 0 ptp_rq0_cache_waive: 0 ptp_rq0_congst_umr: 0 ptp_rq0_arfs_err: 0 ptp_rq0_recover: 0 Fixes: a28359e922c6 ("net/mlx5e: Add PTP-RX statistics") Signed-off-by: Lama Kayal <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-09-30net/mlx5: Fix setting number of EQs of SFsShay Drory1-2/+3
When setting number of completion EQs of the SF, consider number of online CPUs. Without this consideration, when number of online cpus are less than 8, unnecessary 8 completion EQs are allocated. Fixes: c36326d38d93 ("net/mlx5: Round-Robin EQs over IRQs") Signed-off-by: Shay Drory <[email protected]> Reviewed-by: Parav Pandit <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-09-30net/mlx5: Fix length of irq_index in charsShay Drory1-2/+2
The maximum irq_index can be 2047, This means irq_name should have 4 characters reserve for the irq_index. Hence, increase it to 4. Fixes: 3af26495a247 ("net/mlx5: Enlarge interrupt field in CREATE_EQ") Signed-off-by: Shay Drory <[email protected]> Reviewed-by: Parav Pandit <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-09-30net/mlx5: Avoid generating event after PPS out in Real time modeAya Levin1-8/+6
When in Real-time mode, HW clock is synced with the PTP daemon. Hence driver should not re-calibrate the next pulse (via MTPPSE repetitive events mechanism). This patch arms repetitive events only in free-running mode. Fixes: 432119de33d9 ("net/mlx5: Add cyc2time HW translation mode support") Signed-off-by: Aya Levin <[email protected]> Reviewed-by: Eran Ben Elisha <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-09-30net/mlx5: Force round second at 1PPS out start timeAya Levin1-14/+11
Allow configuration of 1PPS start time only with time-stamp representing a round second. Prior to this patch driver allowed setting of a non-round-second which is not supported by the device. Avoid unexpected behavior by restricting start-time configuration to a round-second. Fixes: 4272f9b88db9 ("net/mlx5e: Change 1PPS out scheme") Signed-off-by: Aya Levin <[email protected]> Reviewed-by: Eran Ben Elisha <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-09-30net/mlx5: E-Switch, Fix double allocation of acl flow counterMoshe Shemesh2-5/+11
Flow counter is allocated in eswitch legacy acl setting functions without checking if already allocated by previous setting. Add a check to avoid such double allocation. Fixes: 07bab9502641 ("net/mlx5: E-Switch, Refactor eswitch ingress acl codes") Fixes: ea651a86d468 ("net/mlx5: E-Switch, Refactor eswitch egress acl codes") Signed-off-by: Moshe Shemesh <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-09-30net/mlx5e: Improve MQPRIO resiliencyTariq Toukan2-32/+80
* Add netdev->tc_to_txq rollback in case of failure in mlx5e_update_netdev_queues(). * Fix broken transition between the two modes: MQPRIO DCB mode with tc==8, and MQPRIO channel mode. * Disable MQPRIO channel mode if re-attaching with a different number of channels. * Improve code sharing. Fixes: ec60c4581bd9 ("net/mlx5e: Support MQPRIO channel mode") Signed-off-by: Tariq Toukan <[email protected]> Reviewed-by: Maxim Mikityanskiy <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-09-30net/mlx5e: Keep the value for maximum number of channels in-syncTariq Toukan6-34/+57
The value for maximum number of channels is first calculated based on the netdev's profile and current function resources (specifically, number of MSIX vectors, which depends among other things on the number of online cores in the system). This value is then used to calculate the netdev's number of rxqs/txqs. Once created (by alloc_etherdev_mqs), the number of netdev's rxqs/txqs is constant and we must not exceed it. To achieve this, keep the maximum number of channels in sync upon any netdevice re-attach. Use mlx5e_get_max_num_channels() for calculating the number of netdev's rxqs/txqs. After netdev is created, use mlx5e_calc_max_nch() (which coinsiders core device resources, profile, and netdev) to init or update priv->max_nch. Before this patch, the value of priv->max_nch might get out of sync, mistakenly allowing accesses to out-of-bounds objects, which would crash the system. Track the number of channels stats structures used in a separate field, as they are persistent to suspend/resume operations. All the collected stats of every channel index that ever existed should be preserved. They are reset only when struct mlx5e_priv is, in mlx5e_priv_cleanup(), which is part of the profile changing flow. There is no point anymore in blocking a profile change due to max_nch mismatch in mlx5e_netdev_change_profile(). Remove the limitation. Fixes: a1f240f18017 ("net/mlx5e: Adjust to max number of channles when re-attaching") Signed-off-by: Tariq Toukan <[email protected]> Reviewed-by: Aya Levin <[email protected]> Reviewed-by: Maxim Mikityanskiy <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-09-30net/mlx5e: IPSEC RX, enable checksum completeRaed Salem1-6/+1
Currently in Rx data path IPsec crypto offloaded packets uses csum_none flag, so checksum is handled by the stack, this naturally have some performance/cpu utilization impact on such flows. As Nvidia NIC starting from ConnectX6DX provides checksum complete value out of the box also for such flows there is no sense in taking csum_none path, furthermore the stack (xfrm) have the method to handle checksum complete corrections for such flows i.e. IPsec trailer removal and consequently checksum value adjustment. Because of the above and in addition the ConnectX6DX is the first HW which supports IPsec crypto offload then it is safe to report csum complete for IPsec offloaded traffic. Fixes: b2ac7541e377 ("net/mlx5e: IPsec: Add Connect-X IPsec Rx data path offload") Signed-off-by: Raed Salem <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
2021-09-30net: stmmac: fix EEE init issue when paired with EEE capable PHYsWong Vee Khee1-0/+4
When STMMAC is paired with Energy-Efficient Ethernet(EEE) capable PHY, and the PHY is advertising EEE by default, we need to enable EEE on the xPCS side too, instead of having user to manually trigger the enabling config via ethtool. Fixed this by adding xpcs_config_eee() call in stmmac_eee_init(). Fixes: 7617af3d1a5e ("net: pcs: Introducing support for DWC xpcs Energy Efficient Ethernet") Cc: Michael Sit Wei Hong <[email protected]> Signed-off-by: Wong Vee Khee <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2021-09-29net: hns3: disable firmware compatible features when uninstall PFGuangbin Huang1-8/+13
Currently, the firmware compatible features are enabled in PF driver initialization process, but they are not disabled in PF driver deinitialization process and firmware keeps these features in enabled status. In this case, if load an old PF driver (for example, in VM) which not support the firmware compatible features, firmware will still send mailbox message to PF when link status changed and PF will print "un-supported mailbox message, code = 201". To fix this problem, disable these firmware compatible features in PF driver deinitialization process. Fixes: ed8fb4b262ae ("net: hns3: add link change event report") Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.