aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
AgeCommit message (Collapse)AuthorFilesLines
2020-09-27bnxt_en: ethtool: support PAM4 link speeds up to 200GEdwin Peer1-8/+63
Add ethtool PAM4 link modes for: 50000baseCR_Full 100000baseCR2_Full 200000baseCR4_Full Signed-off-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27bnxt_en: add basic infrastructure to support PAM4 link speedsEdwin Peer2-21/+65
The firmware interface has added support for new link speeds using PAM4 modulation. Expand the bnxt_link_info structure to closely mirror the new firmware structures. Add logic to copy the PAM4 capabilities and settings from the firmware. Signed-off-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27bnxt_en: refactor bnxt_get_fw_speed()Edwin Peer1-23/+24
It will be necessary to update more than one field in the link_info structure when PAM4 speeds are added in a later patch. Instead of merely translating ethtool speed values to firmware speed values, change the responsiblity of this function to update all the necessary link_info fields required to force the speed change to the desired ethtool value. This also reduces code duplication somewhat at the two call sites, which otherwise both have to independently update link_info fields to turn off auto negotiation advertisements. Also use the appropriate REQ_FORCE_LINK_SPEED definitions. These happen to have the same values, but req_link_speed is utilimately passed as force_link_speed in HWRM_PORT_PHY_CFG which is not defined in terms of REQ_AUTO_LINK_SPEED. Reviewed-by: Scott Branden <[email protected]> Signed-off-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27bnxt_en: refactor code to limit speed advertisingEdwin Peer1-8/+12
Extract the code for determining an advertised speed is no longer supported into a separate function. This will avoid some code duplication in a later patch when supporting PAM4 speeds, since these speeds are specified in a separate field. Reviewed-by: Scott Branden <[email protected]> Signed-off-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27bnxt_en: Update firmware interface spec to 1.10.1.65.Michael Chan5-113/+361
The main changes include FEC, ECN statistics, HWRM_PORT_PHY_QCFG response size reduction, and a new counter added to ctx_hw_stats_ext struct to support the new 58818 chip. The ctx_hw_stats_ext structure is now the superset supporting the new 58818 chips and the prior P5 chips. Add a new flag to identify the new chip and use constants for the chip specific ring statistics sizes instead of the size of the structure. Because the HWRM_PORT_PHY_QCFG response structure size has shrunk back to 96 bytes, the workaround added earlier to limit the size of this message for forwarding to the VF can be removed. Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27net: marvell: mvpp2: Fix W=1 warning with !CONFIG_ACPIAndrew Lunn1-0/+2
rivers/net/ethernet/marvell/mvpp2/mvpp2_main.c:7084:36: warning: ‘mvpp2_acpi_match’ defined but not used [-Wunused-const-variable=] 7084 | static const struct acpi_device_id mvpp2_acpi_match[] = { | ^~~~~~~~~~~~~~~~ Wrap the definition inside #ifdef/#endif. Compile tested only. Signed-off-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27mlxsw: spectrum_ethtool: Expose transceiver_overheat counterAmit Cohen1-1/+56
Add structures for port statistics which read from core and not directly from registers. When netdev's ethtool statistics are queried, query the corresponding module's overheat counter from core and expose it as "transceiver_overheat". Signed-off-by: Amit Cohen <[email protected]> Reviewed-by: Jiri Pirko <[email protected]> Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27mlxsw: Update module's settings when module is plugged inAmit Cohen4-0/+137
Module temperature warning events are enabled for modules that have a temperature sensor and configured according to the temperature thresholds queried from the module. When a module is unplugged we are guaranteed not to get temperature warning events. However, when a module is plugged in we need to potentially update its current settings (i.e., event enablement and thresholds). Register to port module plug/unplug events and update module's settings upon plug in events. Signed-off-by: Amit Cohen <[email protected]> Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27mlxsw: spectrum: Initialize netdev's module overheat counterAmit Cohen2-0/+26
The overheat counter is a per-module counter, but it is exposed as part of the corresponding netdev's statistics. It should therefore be presented to user space relative to the netdev's lifetime. Query the counter just before registering the netdev, so that the value exposed to user space will be relative to this initial value. Signed-off-by: Amit Cohen <[email protected]> Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27mlxsw: Enable temperature event for all supported port module sensorsAmit Cohen2-0/+107
MTWE (Management Temperature Warning Event) is triggered for sensors whose temperature event enable bit is enabled in the MTMP register. Enable events for all the modules that have a temperature sensor. Signed-off-by: Amit Cohen <[email protected]> Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27mlxsw: Update transceiver_overheat counter according to MTWEAmit Cohen6-0/+99
MTWE (Management Temperature Warning Event) is triggered when module's temperature is higher than its threshold. Register for MTWE events and increase the module's overheat counter when its corresponding sensor goes above the configured threshold. Signed-off-by: Amit Cohen <[email protected]> Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27mlxsw: core: Add an infrastructure to track transceiver overheat counterAmit Cohen4-0/+96
Initialize an array that stores per-module overheat state and a counter indicating how many times the module was in overheat state. Export a function to query the counter according to module number. Will be used later on by the switch driver (i.e., mlxsw_spectrum) to expose module's overheat counter as part of ethtool statistics. Initialize mlxsw_env after driver initialization to be able to query number of modules from MGPIR register. Signed-off-by: Amit Cohen <[email protected]> Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27mlxsw: core_hwmon: Query MTMP before writing to set only relevant fieldsAmit Cohen1-4/+17
The MTMP register controls various temperature settings on a per-sensor basis. Subsequent patches are going to alter some of these settings for sensors found on port modules in response to certain events. In order to prevent the current callers that write to MTMP from overriding these settings, have them first query the register and then change only the relevant register fields. Signed-off-by: Amit Cohen <[email protected]> Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27mlxsw: reg: Add Ports Module Administrative and Operational Status RegisterAmit Cohen1-0/+59
PMAOS register configures and retrieves the per module status. The register is used also for enabling event for status change. It will be used to enable PMPE (Port Module Plug/Unplug) event. Signed-off-by: Amit Cohen <[email protected]> Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27mlxsw: reg: Add Port Module Plug/Unplug Event RegisterAmit Cohen1-0/+45
PMPE register reports any operational status change of a module. It will be used for enabling temperature warning event when a module is plugged in. Signed-off-by: Amit Cohen <[email protected]> Reviewed-by: Jiri Pirko <[email protected]> Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27mlxsw: reg: Add Management Temperature Warning Event RegisterAmit Cohen1-0/+18
Add MTWE (Management Temperature Warning Event) register, which is used for over temperature warning. Signed-off-by: Amit Cohen <[email protected]> Reviewed-by: Jiri Pirko <[email protected]> Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27net: hns3: add a structure for IR shaper's parameter in hclge_shaper_para_calc()Huazhong Tan2-44/+49
As function hclge_shaper_para_calc() has too many arguments to add more, so encapsulate its three arguments ir_b, ir_u, ir_s into a structure. Signed-off-by: Huazhong Tan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27net: hns3: add a check for device specifications queried from firmwareGuangbin Huang2-0/+28
The device specifications querying is unsupported by the old firmware, in this case, these specifications are 0. However, some specifications should not be 0 or will cause problem. So after querying from firmware, some device specifications are needed to check their value and set to default value if their values are 0. Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: Huazhong Tan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27net: hns3: replace the macro of max tm rate with the queried specificationGuangbin Huang5-13/+29
The max tm rate is a fixed value(100Gb/s) now as it is defined by a macro. In order to support other rates in different kinds of device, it is better to use specification queried from firmware to replace this macro. As function hclge_shaper_para_calc() has too many arguments to add more, so encapsulate its three arguments ir_b, ir_u, ir_s into a structure. Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: Huazhong Tan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27net: hns3: add support to query device specificationsGuangbin Huang5-1/+167
To improve code maintainability and compatibility, new commands HCLGE_OPC_QUERY_DEV_SPECS for PF and HCLGEVF_OPC_QUERY_DEV_SPECS for VF are introduced to query device specifications, instead of statically defining specifications by checking the hardware version or other methods. Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: Huazhong Tan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27net: hns3: add debugfs to dump device capabilitiesGuangbin Huang1-0/+24
Adds debugfs to dump each device capability whether is supported. Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: Huazhong Tan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27net: hns3: use capabilities queried from firmwareGuangbin Huang6-19/+145
In order to improve code maintainability and compatibility, the capabilities of new features are queried from firmware. The member flag in struct hnae3_ae_dev indicates not only capabilities, but some initialized status. As capabilities bits queried from firmware is too many, it is better to use new member to indicate them. So adds member capabs in struce hnae3_ae_dev. Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: Huazhong Tan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27net: hns3: use capability flag to indicate FECGuangbin Huang4-4/+11
Currently, the revision of the pci device is used to identify whether FEC is supported, which is not good for maintainability and compatibility. So use a capability flag to do that. Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: Huazhong Tan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27net: hns3: add support to query device capabilityGuangbin Huang5-18/+29
In order to improve code maintainability and compatibility, add support to query the device capability by expanding the existing version query command. The device capability refers to the features supported by the device. Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: Huazhong Tan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27net: hns3: delete redundant PCI revision judgementGuangbin Huang2-5/+1
Fibre device of PCI revision 0x20 don't support autoneg, and the ops get_autoneg() return AUTONEG_DISABLE so function hns3_nway_reset() will return earlier than judging PCI revision. Function hclge_handle_rocee_ras_error() don't need to judge PCI revision again because its caller hclge_handle_hw_ras_error() has judged once. Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: Huazhong Tan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27net: hns3: add device version to replace pci revisionGuangbin Huang10-69/+100
To better identify the device version, struct hnae3_handle adds a member dev_version to replace pci revision. The dev_version consists of hardware version and PCI revision. The hardware version is queried from firmware by an existing firmware version query command. Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: Huazhong Tan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27mlxsw: spectrum_acl: Fix mlxsw_sp_acl_tcam_group_add()'s error pathIdo Schimmel1-1/+2
If mlxsw_sp_acl_tcam_group_id_get() fails, the mutex initialized earlier is not destroyed. Fix this by initializing the mutex after calling the function. This is symmetric to mlxsw_sp_acl_tcam_group_del(). Fixes: 5ec2ee28d27b ("mlxsw: spectrum_acl: Introduce a mutex to guard region list updates") Signed-off-by: Ido Schimmel <[email protected]> Reviewed-by: Jiri Pirko <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-26net: mscc: ocelot: move NPI port configuration to DSAVladimir Oltean2-37/+10
Remove the ocelot_configure_cpu() function, which was in fact bringing up 2 ports: the CPU port module, which both switchdev and DSA have, and the NPI port, which only DSA has. The (non-Ethernet) CPU port module is at a fixed index in the analyzer, whereas the NPI port is selected through the "ethernet" property in the device tree. Therefore, the function to set up an NPI port is DSA-specific, so we move it there, simplifying the ocelot switch library a little bit. Cc: Horatiu Vultur <[email protected]> Cc: Alexandre Belloni <[email protected]> Cc: UNGLinuxDriver <[email protected]> Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25ice: add support for flash update overwrite maskJacob Keller3-4/+33
Support the recently added DEVLINK_ATTR_FLASH_UPDATE_OVERWRITE_MASK parameter in the ice flash update handler. Convert the overwrite mask bitfield into the appropriate preservation level used by the firmware when updating. Because there is no equivalent preservation level for overwriting only identifiers, this combination is rejected by the driver as not supported with an appropriate extended ACK message. Signed-off-by: Jacob Keller <[email protected]> Reviewed-by: Jakub Kicinski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25devlink: convert flash_update to use params structureJacob Keller7-25/+23
The devlink core recently gained support for checking whether the driver supports a flash_update parameter, via `supported_flash_update_params`. However, parameters are specified as function arguments. Adding a new parameter still requires modifying the signature of the .flash_update callback in all drivers. Convert the .flash_update function to take a new `struct devlink_flash_update_params` instead. By using this structure, and the `supported_flash_update_params` bit field, a new parameter to flash_update can be added without requiring modification to existing drivers. As before, all parameters except file_name will require driver opt-in. Because file_name is a necessary field to for the flash_update to make sense, no "SUPPORTED" bitflag is provided and it is always considered valid. All future additional parameters will require a new bit in the supported_flash_update_params bitfield. Signed-off-by: Jacob Keller <[email protected]> Reviewed-by: Jakub Kicinski <[email protected]> Cc: Jiri Pirko <[email protected]> Cc: Jakub Kicinski <[email protected]> Cc: Jonathan Corbet <[email protected]> Cc: Michael Chan <[email protected]> Cc: Bin Luo <[email protected]> Cc: Saeed Mahameed <[email protected]> Cc: Leon Romanovsky <[email protected]> Cc: Ido Schimmel <[email protected]> Cc: Danielle Ratson <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25devlink: check flash_update parameter support in net coreJacob Keller7-30/+5
When implementing .flash_update, drivers which do not support per-component update are manually checking the component parameter to verify that it is NULL. Without this check, the driver might accept an update request with a component specified even though it will not honor such a request. Instead of having each driver check this, move the logic into net/core/devlink.c, and use a new `supported_flash_update_params` field in the devlink_ops. Drivers which will support per-component update must now specify this by setting DEVLINK_SUPPORT_FLASH_UPDATE_COMPONENT in the supported_flash_update_params in their devlink_ops. This helps ensure that drivers do not forget to check for a NULL component if they do not support per-component update. This also enables a slightly better error message by enabling the core stack to set the netlink bad attribute message to indicate precisely the unsupported attribute in the message. Going forward, any new additional parameter to flash update will require a bit in the supported_flash_update_params bitfield. Signed-off-by: Jacob Keller <[email protected]> Reviewed-by: Jakub Kicinski <[email protected]> Cc: Jiri Pirko <[email protected]> Cc: Jonathan Corbet <[email protected]> Cc: Michael Chan <[email protected]> Cc: Bin Luo <[email protected]> Cc: Saeed Mahameed <[email protected]> Cc: Leon Romanovsky <[email protected]> Cc: Ido Schimmel <[email protected]> Cc: Danielle Ratson <[email protected]> Cc: Shannon Nelson <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25net: atlantic: fix build when object tree is separateIgor Russkikh1-2/+2
Driver subfolder files refer parent folder includes in an absolute manner. Makefile contains a -I for this, but apparently that does not work if object tree is separated. Adding srctree to fix that. Signed-off-by: Igor Russkikh <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25dpaa2-mac: Fix potential null pointer dereferenceGustavo A. R. Silva1-1/+1
There is a null-check for _pcs_, but it is being dereferenced prior to this null-check. So, if _pcs_ can actually be null, then there is a potential null pointer dereference that should be fixed by null-checking _pcs_ before being dereferenced. Addresses-Coverity-ID: 1497159 ("Dereference before null check") Fixes: 94ae899b2096 ("dpaa2-mac: add PCS support through the Lynx module") Signed-off-by: Gustavo A. R. Silva <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25dpaa2-eth: install a single steering rule when SHARED_FS is enabledIonut-robert Aron3-1/+17
When SHARED_FS is enabled on a DPNI object the flow steering tables are shared between all the traffic classes. Modify the driver so that we only add a new flow steering entry on the TC#0 when this new option is enabled. Signed-off-by: Ionut-robert Aron <[email protected]> Signed-off-by: Ioana Ciornei <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25dpaa2-eth: no need to check link state right after ndo_openIoana Ciornei1-12/+1
The call to dpaa2_eth_link_state_update() is a leftover from the time when on DPAA2 platforms the PHYs were started at boot time so when an ifconfig was issued on the associated interface, the link status needed to be checked directly from the ndo_open() callback. This is not needed anymore since we are now properly integrated with the PHY layer thus a link interrupt will come directly from the PHY eventually without the need to call the sync function. Fix this up by removing the call to dpaa2_eth_link_state_update(). Signed-off-by: Ioana Ciornei <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25dpaa2-mac: do not check for both child and parent DTS nodesIoana Ciornei1-2/+1
There is no need to check if both the MDIO controller node and its child node, the PCS device, are available since there is no chance that the child node would be enabled when the parent it's not. Suggested-by: Andrew Lunn <[email protected]> Signed-off-by: Ioana Ciornei <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25dpaa2-eth: fix command version for Tx shapingIoana Ciornei1-1/+3
When adding the support for TBF offload, the improper command version was added even though the command format is for the V2 of dpni_set_tx_shaping(). This does not affect the functionality of TBF since the only change between these two versions is the addition of the exceeded parameters which are not used in TBF. Still, fix the bug so that we keep things in sync. Fixes: 39344a89623d ("dpaa2-eth: add API for Tx shaping") Signed-off-by: Ioana Ciornei <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25net: ethernet: cavium: octeon_mgmt: use phy_start and phy_stopIvan Khoronzhuk1-2/+4
To start also "phy state machine", with UP state as it should be, the phy_start() has to be used, in another case machine even is not triggered. After this change negotiation is supposed to be triggered by SM workqueue. It's not correct usage, but it appears after the following patch, so add it as a fix. Fixes: 74a992b3598a ("net: phy: add phy_check_link_status") Signed-off-by: Ivan Khoronzhuk <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25net: stmmac: Fix clock handling on remove pathWong Vee Khee1-1/+0
While unloading the dwmac-intel driver, clk_disable_unprepare() is being called twice in stmmac_dvr_remove() and intel_eth_pci_remove(). This causes kernel panic on the second call. Removing the second call of clk_disable_unprepare() in intel_eth_pci_remove(). Fixes: 09f012e64e4b ("stmmac: intel: Fix clock handling on error and remove paths") Cc: Andy Shevchenko <[email protected]> Reviewed-by: Voon Weifeng <[email protected]> Signed-off-by: Wong Vee Khee <[email protected]> Reviewed-by: Andy Shevchenko <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25net: stmmac: Add option for VLAN filter fail queue enableChuah, Kim Tatt6-2/+30
Add option in plat_stmmacenet_data struct to enable VLAN Filter Fail Queuing. This option allows packets that fail VLAN filter to be routed to a specific Rx queue when Receive All is also set. When this option is enabled: - Enable VFFQ only when entering promiscuous mode, because Receive All will pass up all rx packets that failed address filtering (similar to promiscuous mode). - VLAN-promiscuous mode is never entered to allow rx packet to fail VLAN filters and get routed to selected VFFQ Rx queue. Reviewed-by: Voon Weifeng <[email protected]> Reviewed-by: Ong Boon Leong <[email protected]> Signed-off-by: Chuah, Kim Tatt <[email protected]> Signed-off-by: Ong Boon Leong <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25drivers/net/ethernet: clean up mis-targeted commentsJesse Brandeburg72-682/+794
As part of the W=1 cleanups for ethernet, a million [*] driver comments had to be cleaned up to get the W=1 compilation to succeed. This change finally makes the drivers/net/ethernet tree compile with W=1 set on the command line. NOTE: The kernel uses kdoc style (see Documentation/process/kernel-doc.rst) when documenting code, not doxygen or other styles. After this patch the x86_64 build has no warnings from W=1, however scripts/kernel-doc says there are 1545 more warnings in source files, that I need to develop a script to fix in a followup patch. The errors fixed here are all kdoc of a few classes, with a few outliers: In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10: drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=] 1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff }; | ^~~~~~~~~~~~~~ ... repeats 4 times... drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body] 2084 | RX_USED_ADD(page, i); drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’: drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable] 603 | u32 tbisr, tanar, tanlpar; | ^~~~~ drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’: drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable] 1207 | u32 cfg, tanar, tbicr; | ^~~~~ drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable] 1063 | int data_size, yf_size; | ^~~~~~~ Normal kdoc fixes: warning: Function parameter or member 'x' not described in 'y' warning: Excess function parameter 'x' description in 'y' warning: Cannot understand <string> on line <NNN> - I thought it was a doc line [*] - ok it wasn't quite a million, but it felt like it. Signed-off-by: Jesse Brandeburg <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25sfc: fix kdoc warningJesse Brandeburg2-1/+2
kernel-doc script as used by W=1, is confused by the macro usage inside the header describing the efx_ptp_data struct. drivers/net/ethernet/sfc/ptp.c:345: warning: Function parameter or member 'MC_CMD_PTP_IN_TRANSMIT_LENMAX' not described in 'efx_ptp_data' After some discussion on the list, break this patch out to a separate one, and fix the issue through a creative macro declaration. Signed-off-by: Jesse Brandeburg <[email protected]> Acked-by: Edward Cree <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25drivers/net/ethernet: remove incorrectly formatted docJesse Brandeburg3-15/+15
As part of the W=1 series for ethernet, these drivers were discovered to be using kdoc style comments but were not actually doing kdoc. The kernel uses kdoc style when documenting code, not doxygen or other styles. Fixed Warnings: drivers/net/ethernet/amazon/ena/ena_com.c:613: warning: Function parameter or member 'ena_dev' not described in 'ena_com_set_llq' drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_b0.c:1540: warning: Cannot understand * @brief Set VLAN filter table drivers/net/ethernet/xilinx/ll_temac_main.c:114: warning: Function parameter or member 'lp' not described in 'temac_indirect_busywait' drivers/net/ethernet/xilinx/ll_temac_main.c:129: warning: Function parameter or member 'lp' not described in 'temac_indirect_in32' drivers/net/ethernet/xilinx/ll_temac_main.c:129: warning: Function parameter or member 'reg' not described in 'temac_indirect_in32' drivers/net/ethernet/xilinx/ll_temac_main.c:147: warning: Function parameter or member 'lp' not described in 'temac_indirect_in32_locked' drivers/net/ethernet/xilinx/ll_temac_main.c:147: warning: Function parameter or member 'reg' not described in 'temac_indirect_in32_locked' drivers/net/ethernet/xilinx/ll_temac_main.c:172: warning: Function parameter or member 'lp' not described in 'temac_indirect_out32' drivers/net/ethernet/xilinx/ll_temac_main.c:172: warning: Function parameter or member 'reg' not described in 'temac_indirect_out32' drivers/net/ethernet/xilinx/ll_temac_main.c:172: warning: Function parameter or member 'value' not described in 'temac_indirect_out32' drivers/net/ethernet/xilinx/ll_temac_main.c:188: warning: Function parameter or member 'lp' not described in 'temac_indirect_out32_locked' drivers/net/ethernet/xilinx/ll_temac_main.c:188: warning: Function parameter or member 'reg' not described in 'temac_indirect_out32_locked' drivers/net/ethernet/xilinx/ll_temac_main.c:188: warning: Function parameter or member 'value' not described in 'temac_indirect_out32_locked' drivers/net/ethernet/xilinx/ll_temac_main.c:212: warning: Function parameter or member 'lp' not described in 'temac_dma_in32_be' drivers/net/ethernet/xilinx/ll_temac_main.c:212: warning: Function parameter or member 'reg' not described in 'temac_dma_in32_be' drivers/net/ethernet/xilinx/ll_temac_main.c:228: warning: Function parameter or member 'lp' not described in 'temac_dma_out32_be' drivers/net/ethernet/xilinx/ll_temac_main.c:228: warning: Function parameter or member 'reg' not described in 'temac_dma_out32_be' drivers/net/ethernet/xilinx/ll_temac_main.c:228: warning: Function parameter or member 'value' not described in 'temac_dma_out32_be' drivers/net/ethernet/xilinx/ll_temac_main.c:247: warning: Function parameter or member 'lp' not described in 'temac_dma_dcr_in' drivers/net/ethernet/xilinx/ll_temac_main.c:247: warning: Function parameter or member 'reg' not described in 'temac_dma_dcr_in' drivers/net/ethernet/xilinx/ll_temac_main.c:255: warning: Function parameter or member 'lp' not described in 'temac_dma_dcr_out' drivers/net/ethernet/xilinx/ll_temac_main.c:255: warning: Function parameter or member 'reg' not described in 'temac_dma_dcr_out' drivers/net/ethernet/xilinx/ll_temac_main.c:255: warning: Function parameter or member 'value' not described in 'temac_dma_dcr_out' drivers/net/ethernet/xilinx/ll_temac_main.c:265: warning: Function parameter or member 'lp' not described in 'temac_dcr_setup' drivers/net/ethernet/xilinx/ll_temac_main.c:265: warning: Function parameter or member 'op' not described in 'temac_dcr_setup' drivers/net/ethernet/xilinx/ll_temac_main.c:265: warning: Function parameter or member 'np' not described in 'temac_dcr_setup' drivers/net/ethernet/xilinx/ll_temac_main.c:300: warning: Function parameter or member 'ndev' not described in 'temac_dma_bd_release' drivers/net/ethernet/xilinx/ll_temac_main.c:330: warning: Function parameter or member 'ndev' not described in 'temac_dma_bd_init' drivers/net/ethernet/xilinx/ll_temac_main.c:600: warning: Function parameter or member 'ndev' not described in 'temac_setoptions' drivers/net/ethernet/xilinx/ll_temac_main.c:600: warning: Function parameter or member 'options' not described in 'temac_setoptions' Signed-off-by: Jesse Brandeburg <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25drivers/net/ethernet: add some basic kdoc tagsJesse Brandeburg2-2/+2
A couple of drivers had a "generic documentation" section that would trigger a "can't understand" message from W=1 compiles. Fix by using correct DOC: tags in the generic sections. Fixed Warnings: drivers/net/ethernet/arc/emac_arc.c:4: info: Scanning doc for c drivers/net/ethernet/cadence/macb_pci.c:3: warning: missing initial short description on line: * Cadence GEM PCI wrapper. drivers/net/ethernet/cadence/macb_pci.c:3: info: Scanning doc for Cadence Signed-off-by: Jesse Brandeburg <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25drivers/net/ethernet: handle one warning explicitlyJesse Brandeburg1-0/+10
While fixing the W=1 builds, this warning came up because the developers used a very tricky way to get structures initialized to a non-zero value, but this causes GCC to warn about an override. In this case the override was intentional, so just disable the warning for this code with a kernel macro that results in disabling the warning for compiles on GCC versions after 8. It is not appropriate to change the struct to initialize all the values as it will just add a lot more code for no value. The code is completely correct as is, we just want to acknowledge that this code could generate a warning and we're ok with that. NOTE: the __diag_ignore macro currently only accepts a second argument of 8 (version 80000), it's either use this one or open code the pragma. Fixed Warnings example (all the same): drivers/net/ethernet/renesas/sh_eth.c:51:12: warning: initialized field overwritten [-Woverride-init] drivers/net/ethernet/renesas/sh_eth.c:52:12: warning: initialized field overwritten [-Woverride-init] drivers/net/ethernet/renesas/sh_eth.c:53:13: warning: initialized field overwritten [-Woverride-init] + 256 more... Signed-off-by: Jesse Brandeburg <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25drivers/net/ethernet: rid ethernet of no-prototype warningsJesse Brandeburg2-0/+2
The W=1 builds showed a few files exporting functions (non-static) that were not prototyped. What actually happened is that there were prototypes, but the include file was forgotten in the implementation file. Add the include file and remove the warnings. Fixed Warnings: drivers/net/ethernet/cavium/liquidio/cn68xx_device.c:124:5: warning: no previous prototype for ‘lio_setup_cn68xx_octeon_device’ [-Wmissing-prototypes] drivers/net/ethernet/cavium/liquidio/octeon_mem_ops.c:159:1: warning: no previous prototype for ‘octeon_pci_read_core_mem’ [-Wmissing-prototypes] drivers/net/ethernet/cavium/liquidio/octeon_mem_ops.c:168:1: warning: no previous prototype for ‘octeon_pci_write_core_mem’ [-Wmissing-prototypes] drivers/net/ethernet/cavium/liquidio/octeon_mem_ops.c:176:5: warning: no previous prototype for ‘octeon_read_device_mem64’ [-Wmissing-prototypes] drivers/net/ethernet/cavium/liquidio/octeon_mem_ops.c:185:5: warning: no previous prototype for ‘octeon_read_device_mem32’ [-Wmissing-prototypes] drivers/net/ethernet/cavium/liquidio/octeon_mem_ops.c:194:6: warning: no previous prototype for ‘octeon_write_device_mem32’ [-Wmissing-prototypes] drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_dcb.c:453:6: warning: no previous prototype for ‘hclge_dcb_ops_set’ [-Wmissing-prototypes] Signed-off-by: Jesse Brandeburg <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25drivers/net/ethernet: clean up unused assignmentsJesse Brandeburg15-84/+37
As part of the W=1 compliation series, these lines all created warnings about unused variables that were assigned a value. Most of them are from register reads, but some are just picking up a return value from a function and never doing anything with it. Fixed warnings: .../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable] .../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable] .../ethernet/cortina/gemini.c:512:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable] .../ethernet/cortina/gemini.c:2110:21: warning: variable ‘config0’ set but not used [-Wunused-but-set-variable] .../ethernet/cavium/liquidio/octeon_device.c:1327:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable] .../ethernet/cavium/liquidio/octeon_device.c:1358:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable] .../ethernet/dec/tulip/media.c:322:8: warning: variable ‘setup’ set but not used [-Wunused-but-set-variable] .../ethernet/dec/tulip/de4x5.c:4928:13: warning: variable ‘r3’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:4981:6: warning: variable ‘rx_status’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:6510:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:6087: warning: cannot understand function prototype: 'struct hw_regs ' .../ethernet/microchip/lan743x_main.c:161:6: warning: variable ‘int_en’ set but not used [-Wunused-but-set-variable] .../ethernet/microchip/lan743x_main.c:1702:6: warning: variable ‘int_sts’ set but not used [-Wunused-but-set-variable] .../ethernet/microchip/lan743x_main.c:3041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable] .../ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable] .../ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable] .../ethernet/marvell/mvneta.c:754:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] .../ethernet/neterion/vxge/vxge-traffic.c:33:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable] .../ethernet/neterion/vxge/vxge-traffic.c:160:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable] .../ethernet/neterion/vxge/vxge-traffic.c:490:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable] .../ethernet/neterion/vxge/vxge-traffic.c:2378:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable] .../ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable] .../ethernet/realtek/8139cp.c:1242:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable] .../ethernet/mellanox/mlx4/en_tx.c:858:6: warning: variable ‘ring_cons’ set but not used [-Wunused-but-set-variable] .../ethernet/sis/sis900.c:792:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:878:11: warning: variable ‘rx_ev_pkt_type’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:877:23: warning: variable ‘rx_ev_mcast_pkt’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:877:7: warning: variable ‘rx_ev_hdr_type’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:876:7: warning: variable ‘rx_ev_other_err’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:1646:21: warning: variable ‘buftbl_min’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:2535:32: warning: variable ‘spec’ set but not used [-Wunused-but-set-variable] .../ethernet/via/via-velocity.c:880:6: warning: variable ‘curr_status’ set but not used [-Wunused-but-set-variable] .../ethernet/ti/tlan.c:656:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable] .../ethernet/ti/davinci_emac.c:1230:6: warning: variable ‘num_tx_pkts’ set but not used [-Wunused-but-set-variable] .../ethernet/synopsys/dwc-xlgmac-common.c:516:8: warning: variable ‘str’ set but not used [-Wunused-but-set-variable] .../ethernet/ti/cpsw_new.c:1662:22: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable] The register reads should be OK, because the current implementation of readl and friends will always execute even without an lvalue. When it makes sense, just remove the lvalue assignment and the local. Other times, just remove the offending code, and occasionally, just mark the variable as maybe unused since it could be used in an ifdef or debug scenario. Only compile tested with W=1. Signed-off-by: Jesse Brandeburg <[email protected]> Acked-by: Edward Cree <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25intel: handle unused assignmentsJesse Brandeburg3-149/+131
Remove variables that were storing a return value from a register read or other read, where the return value wasn't used. Those conversions to remove the lvalue of the assignment should be safe because the readl memory mapped reads are marked volatile and should not be optimized out without an lvalue (I suspect a very long time ago this wasn't guaranteed as it is today). These changes are part of a separate patch to make it easier to review. Warnings Fixed: .../intel/e100.c:2596:9: warning: variable ‘err’ set but not used [-Wunused-but-set-variable] .../intel/ixgb/ixgb_hw.c:101:6: warning: variable ‘icr_reg’ set but not used [-Wunused-but-set-variable] .../intel/ixgb/ixgb_hw.c:277:6: warning: variable ‘ctrl_reg’ set but not used [-Wunused-but-set-variable] .../intel/ixgb/ixgb_hw.c:952:15: warning: variable ‘temp_reg’ set but not used [-Wunused-but-set-variable] .../intel/ixgb/ixgb_hw.c:1164:7: warning: variable ‘mdio_reg’ set but not used [-Wunused-but-set-variable] .../intel/e1000/e1000_hw.c:132:6: warning: variable ‘ret_val’ set but not used [-Wunused-but-set-variable] .../intel/e1000/e1000_hw.c:380:6: warning: variable ‘icr’ set but not used [-Wunused-but-set-variable] .../intel/e1000/e1000_hw.c:2378:6: warning: variable ‘signal’ set but not used [-Wunused-but-set-variable] .../intel/e1000/e1000_hw.c:2374:6: warning: variable ‘ctrl’ set but not used [-Wunused-but-set-variable] .../intel/e1000/e1000_hw.c:2373:6: warning: variable ‘rxcw’ set but not used [-Wunused-but-set-variable] .../intel/e1000/e1000_hw.c:4678:15: warning: variable ‘temp’ set but not used [-Wunused-but-set-variable] Signed-off-by: Jesse Brandeburg <[email protected]> Tested-by: Aaron Brown <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25intel-ethernet: clean up W=1 warnings in kdocJesse Brandeburg38-129/+185
This takes care of all of the trivial W=1 fixes in the Intel Ethernet drivers, which allows developers and maintainers to build more of the networking tree with more complete warning checks. There are three classes of kdoc warnings fixed: - cannot understand function prototype: 'x' - Excess function parameter 'x' description in 'y' - Function parameter or member 'x' not described in 'y' All of the changes were trivial comment updates on function headers. Inspired by Lee Jones' series of wireless work to do the same. Compile tested only, and passes simple test of $ git ls-files *.[ch] | egrep drivers/net/ethernet/intel | \ xargs scripts/kernel-doc -none Signed-off-by: Jesse Brandeburg <[email protected]> Tested-by: Aaron Brown <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25ice: fix memory leak in ice_vsi_setupJacob Keller1-1/+13
During ice_vsi_setup, if ice_cfg_vsi_lan fails, it does not properly release memory associated with the VSI rings. If we had used devres allocations for the rings, this would be ok. However, we use kzalloc and kfree_rcu for these ring structures. Using the correct label to cleanup the rings during ice_vsi_setup highlights an issue in the ice_vsi_clear_rings function: it can leave behind stale ring pointers in the q_vectors structure. When releasing rings, we must also ensure that no q_vector associated with the VSI will point to this ring again. To resolve this, loop over all q_vectors and release their ring mapping. Because we are about to free all rings, no q_vector should remain pointing to any of the rings in this VSI. Fixes: 5513b920a4f7 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support") Signed-off-by: Jacob Keller <[email protected]> Tested-by: Aaron Brown <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>