Age | Commit message (Collapse) | Author | Files | Lines |
|
When a frame is injected from CPU, it is required to create an IFH(Inter
frame header) which sits in front of the frame that is transmitted.
This IFH, contains different fields like destination port, to bypass the
analyzer, priotity, etc. Lan966x it is using packing library to set and
get the fields of this IFH. But this seems to be an expensive
operations.
If this is changed with a simpler implementation, the RX will be
improved with ~5Mbit while on the TX is a much bigger improvement as it
is required to set more fields. Below are the numbers for TX.
Before:
[ 5] 0.00-10.02 sec 439 MBytes 367 Mbits/sec 0 sender
After:
[ 5] 0.00-10.00 sec 578 MBytes 485 Mbits/sec 0 sender
Signed-off-by: Horatiu Vultur <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Whenever a frame was received to the CPU, the HW is timestamping the
frame. In the IFH(Inter Frame Header) it is found the nanosecond part
of the timestamps the SW is required to read from HW the second part.
But reading the second part it seems to be a expensive operations, so
so change this such to read the second part only when rx filter is
enabled.
Doing this change gives the RX a performance boost of ~70mbit.
before:
[ 5] 0.00-10.01 sec 546 MBytes 457 Mbits/sec 0 sender
now:
[ 5] 0.00-10.01 sec 652 MBytes 530 Mbits/sec 0 sender
Signed-off-by: Horatiu Vultur <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
As the function always returns 0 change the return type to be
void instead of int. In this way also remove a wrong message
in case of error which would never happen.
Signed-off-by: Horatiu Vultur <[email protected]>
Reviewed-by: Alvin Šipraga <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
IS1 VCAP has it's own list of supported ethernet protocol types which is
different than the IS2 VCAP. Therefore separate the list of known
protocol types based on the VCAP type.
Signed-off-by: Horatiu Vultur <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Allow rules to be chained between IS1 VCAP and IS2 VCAP. Chaining
between IS1 lookups or between IS2 lookups are not supported by the
hardware.
Signed-off-by: Horatiu Vultur <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Enable TC command to use IS1 VCAP
Signed-off-by: Horatiu Vultur <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Add IS1 VCAP port keyset configuration for lan966x and also update debug
fs support to show the keyset configuration.
Signed-off-by: Horatiu Vultur <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Provide IS1 (ingress stage 1) VCAP model for lan966x.
This provides classification actions for lan966x.
Signed-off-by: Horatiu Vultur <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Documentation/bpf/bpf_devel_QA.rst
b7abcd9c656b ("bpf, doc: Link to submitting-patches.rst for general patch submission info")
d56b0c461d19 ("bpf, docs: Fix link to netdev-FAQ target")
https://lore.kernel.org/all/[email protected]/
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This adds support for using the "template add" and "template destroy"
functionality to change the port keyset configuration.
If the VCAP lookup already contains rules, the port keyset is left
unchanged, as a change would make these rules unusable.
When the template is destroyed the port keyset configuration is restored.
The filters using the template chain will automatically be deleted by the
TC framework.
Signed-off-by: Steen Hegelund <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
With this its is now possible for clients (like TC) to change the port
keyset configuration in the Sparx5 VCAPs.
This is typically done per traffic class which is guided with the L3
protocol information.
Before the change the current keyset configuration is collected in a list
that is handed back to the client.
Signed-off-by: Steen Hegelund <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This adds a list that is used to collect the templates that are active on a
port.
This allows the template creation to change the port configuration
and the template destruction to change it back.
Signed-off-by: Steen Hegelund <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This provides these 3 functions in the VCAP API:
- Count the number of rules in a VCAP lookup (chain)
- Remove a key from a VCAP rule
- Find the keyset that gives the smallest rule list from a list of keysets
Signed-off-by: Steen Hegelund <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Correct the name used in the debugfs output.
Signed-off-by: Steen Hegelund <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix deletion of existing DSCP mappings in the APP table.
Adding and deleting DSCP entries are replicated per-port, since the
mapping table is global for all ports in the chip. Whenever a mapping
for a DSCP value already exists, the old mapping is deleted first.
However, it is only deleted for the specified port. Fix this by calling
sparx5_dcb_ieee_delapp() instead of dcb_ieee_delapp() as it ought to be.
Reproduce:
// Map and remap DSCP value 63
$ dcb app add dev eth0 dscp-prio 63:1
$ dcb app add dev eth0 dscp-prio 63:2
$ dcb app show dev eth0 dscp-prio
dscp-prio 63:2
$ dcb app show dev eth1 dscp-prio
dscp-prio 63:1 63:2 <-- 63:1 should not be there
Fixes: 8dcf69a64118 ("net: microchip: sparx5: add support for offloading dscp table")
Signed-off-by: Daniel Machon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When the police was removed from the port, then it was trying to
remove the police from the police id and not from the actual
police index.
The police id represents the id of the police and police index
represents the position in HW where the police is situated.
The port police id can be any number while the port police index
is a number based on the port chip port.
Fix this by deleting the police from HW that is situated at the
police index and not police id.
Fixes: 5390334b59a3 ("net: lan966x: Add port police support using tc-matchall")
Signed-off-by: Horatiu Vultur <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"This features a bunch of new device support, a couple of new drivers,
yaml conversion and updates of a few drivers.
Core support:
- New devm_of_phy_optional_get() API with users and conversion
New hardware support:
- Mediatek MT7986 phy support
- Qualcomm SM8550 UFS, PCIe, combo phy support, SM6115 / SM4250 USB3
phy support, SM6350 combo phy support, SM6125 UFS PHY support amd
SM8350 & SM8450 combo phy support
- Qualcomm SNPS eUSB2 eUSB2 repeater drivers
- Allwinner F1C100s USB PHY support
- Tegra xusb support for Tegra234
Updates:
- Yaml conversion for Qualcomm pcie2 phy and usb-hsic-phy
- G4 mode support in Qualcomm UFS phy and support for various SoCs
- Yaml conversion for Meson usb2 phy
- TI Type C support for usb phy for j721
- Yaml conversion for Tegra xusb binding"
* tag 'phy-for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (106 commits)
phy: qcom: phy-qcom-snps-eusb2: Add support for eUSB2 repeater
phy: qcom: Add QCOM SNPS eUSB2 repeater driver
dt-bindings: phy: qcom,snps-eusb2-phy: Add phys property for the repeater
dt-bindings: phy: Add qcom,snps-eusb2-repeater schema file
dt-bindings: phy: amlogic,g12a-usb3-pcie-phy: add missing optional phy-supply property
phy: rockchip-typec: Fix unsigned comparison with less than zero
phy: rockchip-typec: fix tcphy_get_mode error case
phy: qcom: snps-eusb2: Add missing headers
phy: qcom-qmp-combo: Add support for SM8550
phy: qcom-qmp: Add v6 DP register offsets
phy: qcom-qmp: pcs-usb: Add v6 register offsets
dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp: Document SM8550 compatible
phy: qcom: Add QCOM SNPS eUSB2 driver
dt-bindings: phy: Add qcom,snps-eusb2-phy schema file
phy: qcom-qmp-pcie: Add support for SM8550 g3x2 and g4x2 PCIEs
phy: qcom-qmp: qserdes-lane-shared: Add v6 register offsets
phy: qcom-qmp: qserdes-txrx: Add v6.20 register offsets
phy: qcom-qmp: pcs-pcie: Add v6.20 register offsets
phy: qcom-qmp: pcs-pcie: Add v6 register offsets
phy: qcom-qmp: pcs: Add v6.20 register offsets
...
|
|
Per-next-PR merge.
net/smc/af_smc.c
b5dd4d698171 ("net/smc: llc_conf_mutex refactor, replace it with rw_semaphore")
e40b801b3603 ("net/smc: fix potential panic dues to unprotected smc_llc_srv_add_link()")
https://lore.kernel.org/all/[email protected]/
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
When doing timestamping in lan966x and having PROVE_LOCKING
enabled the following warning is shown.
========================================================
WARNING: possible irq lock inversion dependency detected
6.2.0-rc7-01749-gc54e1f7f7e36 #2786 Tainted: G N
--------------------------------------------------------
swapper/0/0 just changed the state of lock:
c2609f50 (_xmit_ETHER#2){+.-.}-{2:2}, at: sch_direct_xmit+0x16c/0x2e8
but this lock took another, SOFTIRQ-unsafe lock in the past:
(&lan966x->ptp_ts_id_lock){+.+.}-{2:2}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&lan966x->ptp_ts_id_lock);
local_irq_disable();
lock(_xmit_ETHER#2);
lock(&lan966x->ptp_ts_id_lock);
<Interrupt>
lock(_xmit_ETHER#2);
*** DEADLOCK ***
5 locks held by swapper/0/0:
#0: c1001e18 ((&ndev->rs_timer)){+.-.}-{0:0}, at: call_timer_fn+0x0/0x33c
#1: c105e7c4 (rcu_read_lock){....}-{1:2}, at: ndisc_send_skb+0x134/0x81c
#2: c105e7d8 (rcu_read_lock_bh){....}-{1:2}, at: ip6_finish_output2+0x17c/0xc64
#3: c105e7d8 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x4c/0x1224
#4: c3056174 (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+...}-{2:2}, at: __dev_queue_xmit+0x354/0x1224
the shortest dependencies between 2nd lock and 1st lock:
-> (&lan966x->ptp_ts_id_lock){+.+.}-{2:2} {
HARDIRQ-ON-W at:
lock_acquire.part.0+0xb0/0x248
_raw_spin_lock+0x38/0x48
lan966x_ptp_irq_handler+0x164/0x2a8
irq_thread_fn+0x1c/0x78
irq_thread+0x130/0x278
kthread+0xec/0x110
ret_from_fork+0x14/0x28
SOFTIRQ-ON-W at:
lock_acquire.part.0+0xb0/0x248
_raw_spin_lock+0x38/0x48
lan966x_ptp_irq_handler+0x164/0x2a8
irq_thread_fn+0x1c/0x78
irq_thread+0x130/0x278
kthread+0xec/0x110
ret_from_fork+0x14/0x28
INITIAL USE at:
lock_acquire.part.0+0xb0/0x248
_raw_spin_lock_irqsave+0x4c/0x68
lan966x_ptp_txtstamp_request+0x128/0x1cc
lan966x_port_xmit+0x224/0x43c
dev_hard_start_xmit+0xa8/0x2f0
sch_direct_xmit+0x108/0x2e8
__dev_queue_xmit+0x41c/0x1224
packet_sendmsg+0xdb4/0x134c
__sys_sendto+0xd0/0x154
sys_send+0x18/0x20
ret_fast_syscall+0x0/0x1c
}
... key at: [<c174ba0c>] __key.2+0x0/0x8
... acquired at:
_raw_spin_lock_irqsave+0x4c/0x68
lan966x_ptp_txtstamp_request+0x128/0x1cc
lan966x_port_xmit+0x224/0x43c
dev_hard_start_xmit+0xa8/0x2f0
sch_direct_xmit+0x108/0x2e8
__dev_queue_xmit+0x41c/0x1224
packet_sendmsg+0xdb4/0x134c
__sys_sendto+0xd0/0x154
sys_send+0x18/0x20
ret_fast_syscall+0x0/0x1c
-> (_xmit_ETHER#2){+.-.}-{2:2} {
HARDIRQ-ON-W at:
lock_acquire.part.0+0xb0/0x248
_raw_spin_lock+0x38/0x48
netif_freeze_queues+0x38/0x68
dev_deactivate_many+0xac/0x388
dev_deactivate+0x38/0x6c
linkwatch_do_dev+0x70/0x8c
__linkwatch_run_queue+0xd4/0x1e8
linkwatch_event+0x24/0x34
process_one_work+0x284/0x744
worker_thread+0x28/0x4bc
kthread+0xec/0x110
ret_from_fork+0x14/0x28
IN-SOFTIRQ-W at:
lock_acquire.part.0+0xb0/0x248
_raw_spin_lock+0x38/0x48
sch_direct_xmit+0x16c/0x2e8
__dev_queue_xmit+0x41c/0x1224
ip6_finish_output2+0x5f4/0xc64
ndisc_send_skb+0x4cc/0x81c
addrconf_rs_timer+0xb0/0x2f8
call_timer_fn+0xb4/0x33c
expire_timers+0xb4/0x10c
run_timer_softirq+0xf8/0x2a8
__do_softirq+0xd4/0x5fc
__irq_exit_rcu+0x138/0x17c
irq_exit+0x8/0x28
__irq_svc+0x90/0xbc
arch_cpu_idle+0x30/0x3c
default_idle_call+0x44/0xac
do_idle+0xc8/0x138
cpu_startup_entry+0x18/0x1c
rest_init+0xcc/0x168
arch_post_acpi_subsys_init+0x0/0x8
INITIAL USE at:
lock_acquire.part.0+0xb0/0x248
_raw_spin_lock+0x38/0x48
netif_freeze_queues+0x38/0x68
dev_deactivate_many+0xac/0x388
dev_deactivate+0x38/0x6c
linkwatch_do_dev+0x70/0x8c
__linkwatch_run_queue+0xd4/0x1e8
linkwatch_event+0x24/0x34
process_one_work+0x284/0x744
worker_thread+0x28/0x4bc
kthread+0xec/0x110
ret_from_fork+0x14/0x28
}
... key at: [<c175974c>] netdev_xmit_lock_key+0x8/0x1c8
... acquired at:
__lock_acquire+0x978/0x2978
lock_acquire.part.0+0xb0/0x248
_raw_spin_lock+0x38/0x48
sch_direct_xmit+0x16c/0x2e8
__dev_queue_xmit+0x41c/0x1224
ip6_finish_output2+0x5f4/0xc64
ndisc_send_skb+0x4cc/0x81c
addrconf_rs_timer+0xb0/0x2f8
call_timer_fn+0xb4/0x33c
expire_timers+0xb4/0x10c
run_timer_softirq+0xf8/0x2a8
__do_softirq+0xd4/0x5fc
__irq_exit_rcu+0x138/0x17c
irq_exit+0x8/0x28
__irq_svc+0x90/0xbc
arch_cpu_idle+0x30/0x3c
default_idle_call+0x44/0xac
do_idle+0xc8/0x138
cpu_startup_entry+0x18/0x1c
rest_init+0xcc/0x168
arch_post_acpi_subsys_init+0x0/0x8
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G N 6.2.0-rc7-01749-gc54e1f7f7e36 #2786
Hardware name: Generic DT based system
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x58/0x70
dump_stack_lvl from mark_lock.part.0+0x59c/0x93c
mark_lock.part.0 from __lock_acquire+0x978/0x2978
__lock_acquire from lock_acquire.part.0+0xb0/0x248
lock_acquire.part.0 from _raw_spin_lock+0x38/0x48
_raw_spin_lock from sch_direct_xmit+0x16c/0x2e8
sch_direct_xmit from __dev_queue_xmit+0x41c/0x1224
__dev_queue_xmit from ip6_finish_output2+0x5f4/0xc64
ip6_finish_output2 from ndisc_send_skb+0x4cc/0x81c
ndisc_send_skb from addrconf_rs_timer+0xb0/0x2f8
addrconf_rs_timer from call_timer_fn+0xb4/0x33c
call_timer_fn from expire_timers+0xb4/0x10c
expire_timers from run_timer_softirq+0xf8/0x2a8
run_timer_softirq from __do_softirq+0xd4/0x5fc
__do_softirq from __irq_exit_rcu+0x138/0x17c
__irq_exit_rcu from irq_exit+0x8/0x28
irq_exit from __irq_svc+0x90/0xbc
Exception stack(0xc1001f20 to 0xc1001f68)
1f20: ffffffff ffffffff 00000001 c011f840 c100e000 c100e000 c1009314 c1009370
1f40: c10f0c1a c0d5e564 c0f5da8c 00000000 00000000 c1001f70 c010f0bc c010f0c0
1f60: 600f0013 ffffffff
__irq_svc from arch_cpu_idle+0x30/0x3c
arch_cpu_idle from default_idle_call+0x44/0xac
default_idle_call from do_idle+0xc8/0x138
do_idle from cpu_startup_entry+0x18/0x1c
cpu_startup_entry from rest_init+0xcc/0x168
rest_init from arch_post_acpi_subsys_init+0x0/0x8
Fix this by using spin_lock_irqsave/spin_lock_irqrestore also
inside lan966x_ptp_irq_handler.
Fixes: e85a96e48e33 ("net: lan966x: Add support for ptp interrupts")
Signed-off-by: Horatiu Vultur <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Since commit 81e164c4aec5 ("net: microchip: sparx5: Add automatic
selection of VCAP rule actionset") the VCAP API has the capability to
select automatically the actionset based on the actions that are attached
to the rule. So it is not needed anymore to hardcode the actionset in the
driver, therefore it is OK to remove this.
Signed-off-by: Horatiu Vultur <[email protected]>
Reviewed-by: Alexander Lobakin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The vcap_admin structures in vcap_api_next_lookup_advanced_test()
take several hundred bytes of stack frame, but when CONFIG_KASAN_STACK
is enabled, each one of them also has extra padding before and after
it, which ends up blowing the warning limit:
In file included from drivers/net/ethernet/microchip/vcap/vcap_api.c:3521:
drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c: In function 'vcap_api_next_lookup_advanced_test':
drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:1954:1: error: the frame size of 1448 bytes is larger than 1400 bytes [-Werror=frame-larger-than=]
1954 | }
Reduce the total stack usage by replacing the five structures with
an array that only needs one pair of padding areas.
Fixes: 1f741f001160 ("net: microchip: sparx5: Add KUNIT tests for enabling/disabling chains")
Signed-off-by: Arnd Bergmann <[email protected]>
Reviewed-by: Alexander Lobakin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This provides these 3 actions for rule in the ES0 VCAP:
- action vlan pop
- action vlan modify id X priority Y
- action vlan push id X priority Y protocol Z
Signed-off-by: Steen Hegelund <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
This enables the TC command to use the Sparx5 ES0 VCAP, and handling of
rule links between IS0 and ES0.
Signed-off-by: Steen Hegelund <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
This adds the ES0 VCAP port keyset configuration for Sparx5.
Signed-off-by: Steen Hegelund <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
This provides access to the ES0 VCAP register targets
Signed-off-by: Steen Hegelund <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
This provides the VCAP model for the Sparx5 ES0 (Egress Stage 0) VCAP.
This VCAP provides rewriting functionality in the egress path.
Signed-off-by: Steen Hegelund <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Ensure that an error is returned if the VCAP instance was not found.
The chain offset (diff) is allowed to be zero as this just means that the
user did not request rules to be linked.
Signed-off-by: Steen Hegelund <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
This improves the check performed on linked rules when enabling or
disabling them. The chain id used must be the chain id without the offset
used for linking the rules.
Signed-off-by: Steen Hegelund <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
This changes the TPID of the egress frames to use the TPID stored in the
IFH (internal frame header), which ensures that this is the TPID classified
for the frame at ingress.
Signed-off-by: Steen Hegelund <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
The rule counter must be cleared when creating a new rule, even if the VCAP
lookup is currently disabled.
This ensures that rules located in VCAPs that use external counters (such
as Sparx5 IS2 and ES0) will have their counter reset even if the VCAP
lookup is not enabled at the moment.
Signed-off-by: Steen Hegelund <[email protected]>
Fixes: 95fa74148daa ("net: microchip: sparx5: Reset VCAP counter for new rules")
Signed-off-by: Paolo Abeni <[email protected]>
|
|
A valid frame should never use a multicast address as its source MAC
address, so discard these invalid frames.
Signed-off-by: Steen Hegelund <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Set xdp_features netdevice flag if lan966x nic supports xdp mode.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Reviewed-by: Horatiu Vultur <[email protected]>
Link: https://lore.kernel.org/r/01f4412f28899d97b0054c9c1a63694201301b42.1676055718.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Add the following TC flower filter keys to lan966x for IS2:
- ipv4_addr (sip and dip)
- ipv6_addr (sip and dip)
- control (IPv4 fragments)
- portnum (tcp and udp port numbers)
- basic (L3 and L4 protocol)
- vlan (outer vlan tag info)
- tcp (tcp flags)
- ip (tos field)
As the parsing of these keys is similar between lan966x and sparx5, move
the code in a separate file to be shared by these 2 chips. And put the
specific parsing outside of the common functions.
Signed-off-by: Horatiu Vultur <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
net/devlink/leftover.c / net/core/devlink.c:
565b4824c39f ("devlink: change port event netdev notifier from per-net to global")
f05bd8ebeb69 ("devlink: move code to a dedicated directory")
687125b5799c ("devlink: split out core code")
https://lore.kernel.org/all/[email protected]/
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Add flower filter packet statistics. This will just read the TCAM
counter of the rule, which mention how many packages were hit by this
rule.
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Horatiu Vultur <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Since mqprio is a scheduler and not a classifier, move its offload
structure to pkt_sched.h, where struct tc_taprio_qopt_offload also lies.
Also update some header inclusions in drivers that access this
structure, to the best of my abilities.
Cc: Igor Russkikh <[email protected]>
Cc: Yisen Zhuang <[email protected]>
Cc: Salil Mehta <[email protected]>
Cc: Jesse Brandeburg <[email protected]>
Cc: Tony Nguyen <[email protected]>
Cc: Thomas Petazzoni <[email protected]>
Cc: Saeed Mahameed <[email protected]>
Cc: Leon Romanovsky <[email protected]>
Cc: Horatiu Vultur <[email protected]>
Cc: Lars Povlsen <[email protected]>
Cc: Steen Hegelund <[email protected]>
Cc: Daniel Machon <[email protected]>
Cc: [email protected]
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Check all ports instead of just port_count ports. PTP init was only
checking ports 0 to port_count. If the hardware ports are not mapped
starting from 0 then they would be missed, e.g. if only ports 20-30 were
mapped it would attempt to init ports 0-10, resulting in NULL pointers
when attempting to timestamp. Now it will init all mapped ports.
Fixes: 70dfe25cd866 ("net: sparx5: Update extraction/injection for timestamping")
Signed-off-by: Casper Andersson <[email protected]>
Reviewed-by: Horatiu Vultur <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add support for tc actions gate and police, in order to implement
support for configuring PSFP through tc.
Signed-off-by: Daniel Machon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Initialize the SDLB's, stream gates and stream filters.
Signed-off-by: Daniel Machon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add support for configuring PSFP stream filters (IEEE 802.1Q-2018,
8.6.5.1.1).
The VCAP CLM (VCAP IS0 ingress classifier) classifies streams,
identified by ISDX (Ingress Service Index, frame metadata), and maps
ISDX to streams.
Signed-off-by: Daniel Machon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add support for configuring PSFP stream gates (IEEE 802.1Q-2018,
8.6.5.1.2).
Stream gates are time-based policers used by PSFP. Frames are dropped
based on the gate state (OPEN/ CLOSE), whose state will be altered based
on the Gate Control List (GCL) and current PTP time. Apart from
time-based policing, stream gates can alter egress queue selection for
the frames that pass through the Gate. This is done through Internal
Priority Selector (IPS). Stream gates are mapped from stream filters.
Signed-off-by: Daniel Machon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add a new function for calculating PTP basetime, required by the stream
gate scheduler to calculate gate state (open / close).
Signed-off-by: Daniel Machon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add support for configuring PSFP flow-meters (IEEE 802.1Q-2018,
8.6.5.1.3).
The VCAP CLM (VCAP IS0 ingress classifier) classifies streams,
identified by ISDX (Ingress Service Index, frame metadata), and maps
ISDX to flow-meters. SDLB's provide the flow-meter parameters.
Signed-off-by: Daniel Machon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add initial API for configuring policers. This patch add support for
service policers.
Signed-off-by: Daniel Machon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add support for Service Dual Leacky Buckets (SDLB), used to implement
PSFP flow-meters. Buckets are linked together in a leak chain of a leak
group. Leak groups a preconfigured to serve buckets within a certain
rate interval.
Signed-off-by: Daniel Machon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add resource pools and accessor functions. These pools can be queried by
the driver, whenever a finite resource is required. Some resources can
be reused, in which case an index and a reference count is used to keep
track of users.
Signed-off-by: Daniel Machon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add registers needed for PSFP. This patch also renames a single
register, shortening its name (SYS_CLK_PER_100PS). Uses have been update
accordingly.
Signed-off-by: Daniel Machon <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Enable debugfs for vcap for lan966x. This will allow to print all the
entries in the VCAP and also the port information regarding which keys
are configured.
Signed-off-by: Horatiu Vultur <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Use the new devm_of_phy_optional_get() helper instead of open-coding the
same operation.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Reviewed-by: Steen Hegelund <[email protected]>
Link: https://lore.kernel.org/r/993b0f4ac5b84b2b72223011614d2e821f9e7302.1674584626.git.geert+renesas@glider.be
Signed-off-by: Vinod Koul <[email protected]>
|
|
This enhances the KUNIT test of the VCAP API with tests of the chaining
functionality.
Signed-off-by: Steen Hegelund <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|