aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/intel/ixgbe
AgeCommit message (Collapse)AuthorFilesLines
2018-03-23ixgbe: add status reg reads to ixgbe_check_removePaul Greenwalt2-11/+21
Add status register reads and delay between reads to ixgbe_check_remove. Registers can read 0xFFFFFFFF during PCI reset, which causes the driver to remove the adapter. The additional status register reads can reduce the chance of this race condition. If the status register is not 0xFFFFFFFF, then ixgbe_check_remove returns the value of the register being read. Signed-off-by: Paul Greenwalt <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-03-23intel: add SPDX identifiers to all the Intel driversJeff Kirsher18-0/+18
Add the SPDX identifiers to all the Intel wired LAN driver files, as outlined in Documentation/process/license-rules.rst. Signed-off-by: Jeff Kirsher <[email protected]> Tested-by: Aaron Brown <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-03-12ixgbe: fix disabling hide VLAN on VF resetPaul Greenwalt1-1/+5
If port VLAN is enabled, set PFQDE.HIDE_VLAN during VF reset. Setting only PFQDE.PFQDE during VF reset was clearing PFQDE.HIDE_VLAN. Signed-off-by: Paul Greenwalt <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-03-12ixgbe: Add receive length error counterTonghao Zhang1-0/+1
ixgbe enabled rlec counter and the rx_error used it. We can export the counter directly via ethtool -S ethX. Signed-off-by: Tonghao Zhang <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-03-12ixgbe: remove unneeded ipsec state free callbackShannon Nelson1-13/+0
With commit 7f05b467a735 ("xfrm: check for xdo_dev_state_free") we no longer need to add an empty callback function to the driver, so now let's remove the useless code. Signed-off-by: Shannon Nelson <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-03-12ixgbe: fix ipsec trailer lengthShannon Nelson1-1/+23
Fix up the Tx trailer length calculation. We can't believe the trailer len from the xstate information because it was calculated before the packet was put together and padding added. This bit of code finds the padding value in the trailer, adds it to the authentication length, and saves it so later we can put it into the Tx descriptor to tell the device where to stop the checksum calculation. Fixes: 592594704761 ("ixgbe: process the Tx ipsec offload") Signed-off-by: Shannon Nelson <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-03-12ixgbe: check for 128-bit authenticationShannon Nelson2-5/+12
Make sure the Security Association is using a 128-bit authentication, since that's the only size that the hardware offload supports. Signed-off-by: Shannon Nelson <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-03-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-0/+8
All of the conflicts were cases of overlapping changes. In net/core/devlink.c, we have to make care that the resouce size_params have become a struct member rather than a pointer to such an object. Signed-off-by: David S. Miller <[email protected]>
2018-02-26ixgbe: fix crash in build_skb Rx code pathEmil Tantilov1-0/+8
Add check for build_skb enabled ring in ixgbe_dma_sync_frag(). In that case &skb_shinfo(skb)->frags[0] may not always be set which can lead to a crash. Instead we derive the page offset from skb->data. Fixes: 42073d91a214 ("ixgbe: Have the CPU take ownership of the buffers sooner") CC: stable <[email protected]> Reported-by: Ambarish Soman <[email protected]> Suggested-by: Alexander Duyck <[email protected]> Signed-off-by: Emil Tantilov <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-02-26ixgbe: prevent ptp_rx_hang from running when in FILTER_ALL modeJacob Keller1-1/+2
On hardware which supports timestamping all packets, the timestamps are recorded in the packet buffer, and the driver no longer uses or reads the registers. This makes the logic for checking and clearing Rx timestamp hangs meaningless. If we run the ixgbe_ptp_rx_hang() function in this case, then the driver will continuously spam the log output with "Clearing Rx timestamp hang". These messages are spurious, and confusing to end users. The original code in commit a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x devices", 2015-12-03) did have a flag PTP_RX_TIMESTAMP_IN_REGISTER which was intended to be used to avoid the Rx timestamp hang check, however it did not actually check the flag before calling the function. Do so now in order to stop the checks and prevent the spurious log messages. Fixes: a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x devices", 2015-12-03) Signed-off-by: Jacob Keller <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-02-26ixgbe: Avoid to write the RETA table when unnecessaryTonghao Zhang1-2/+2
If indir == 0 in the ixgbe_set_rxfh(), it is unnecessary to write the HW. Because redirection table is not changed. Signed-off-by: Tonghao Zhang <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-02-26ixgbe: remove redundant initialization of 'pool'Colin Ian King1-1/+0
Variable pool is being assigned zero and then in the following for-loop is it being set to zero again. Remove the redundant first assignment. Cleans up clang warning: drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c:61:2: warning: Value stored to 'pool' is never read Signed-off-by: Colin Ian King <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-26ixgbe: don't set RXDCTL.RLPML for 82599Emil Tantilov1-2/+6
commit 2de6aa3a666e ("ixgbe: Add support for padding packet") Uses RXDCTL.RLPML to limit the maximum frame size on Rx when using build_skb. Unfortunately that register does not work on 82599. Added an explicit check to avoid setting this register on 82599 MAC. Extended the comment related to the setting of RXDCTL.RLPML to better explain its purpose. Signed-off-by: Emil Tantilov <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-26ixgbe: Fix && vs || typoDan Carpenter1-1/+1
"offset" can't be both 0x0 and 0xFFFF so presumably || was intended instead of &&. That matches with how this check is done in other functions. Fixes: 73834aec7199 ("ixgbe: extend firmware version support") Signed-off-by: Dan Carpenter <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-26ixgbe: add support for reporting 5G link speedPaul Greenwalt1-0/+3
Since 5G link speed is supported by some devices, add reporting of 5G link speed. Signed-off-by: Paul Greenwalt <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-26ixgbe: Don't report unsupported timestamping filters for X550Miroslav Lichvar1-18/+19
The current code enables on X550 timestamping of all packets for any filter, which means ethtool should not report any PTP-specific filters as unsupported. Signed-off-by: Miroslav Lichvar <[email protected]> Acked-by: Richard Cochran <[email protected]> Acked-by: Jacob Keller <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-26ixgbe: use ARRAY_SIZE for array sizing calculation on array bufColin Ian King1-1/+1
Use the ARRAY_SIZE macro on array buf to determine size of the array. Improvement suggested by coccinelle. Signed-off-by: Colin Ian King <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-25ixgbe: use tc_cls_can_offload_and_chain0()Jakub Kicinski1-4/+1
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case ethtool tc offload flag is not set or chain unsupported. Signed-off-by: Jakub Kicinski <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2018-01-23ixgbe: register ipsec offload with the xfrm subsystemShannon Nelson2-0/+23
With all the support code in place we can now link in the ipsec offload operations and set the ESP feature flag for the XFRM subsystem to see. Signed-off-by: Shannon Nelson <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-23ixgbe: ipsec offload statsShannon Nelson4-1/+10
Add a simple statistic to count the ipsec offloads. Signed-off-by: Shannon Nelson <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-23ixgbe: process the Tx ipsec offloadShannon Nelson5-9/+112
If the skb has a security association referenced in the skb, then set up the Tx descriptor with the ipsec offload bits. While we're here, we fix an oddly named field in the context descriptor struct. Signed-off-by: Shannon Nelson <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-23ixgbe: process the Rx ipsec offloadShannon Nelson3-2/+115
If the chip sees and decrypts an ipsec offload, set up the skb sp pointer with the ralated SA info. Since the chip is rude enough to keep to itself the table index it used for the decryption, we have to do our own table lookup, using the hash for speed. Signed-off-by: Shannon Nelson <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-23ixgbe: restore offloaded SAs after a resetShannon Nelson3-0/+44
On a chip reset most of the table contents are lost, so must be restored. This scans the driver's ipsec tables and restores both the filled and empty table slots to their pre-reset values. Signed-off-by: Shannon Nelson <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-23ixgbe: add ipsec offload add and remove SAShannon Nelson3-1/+399
Add the functions for setting up and removing offloaded SAs (Security Associations) with the x540 hardware. We set up the callback structure but we don't yet set the hardware feature bit to be sure the XFRM service won't actually try to use us for an offload yet. The software tables are made up to mimic the hardware tables to make it easier to track what's in the hardware, and the SA table index is used for the XFRM offload handle. However, there is a hashing field in the Rx SA tracking that will be used to facilitate faster table searches in the Rx fast path. Signed-off-by: Shannon Nelson <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-23ixgbe: add ipsec data structuresShannon Nelson2-0/+45
Set up the data structures to be used by the ipsec offload. Signed-off-by: Shannon Nelson <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-23ixgbe: add ipsec engine start and stop routinesShannon Nelson1-0/+142
Add in the code for running and stopping the hardware ipsec encryption/decryption engine. It is good to keep the engine off when not in use in order to save on the power draw. Signed-off-by: Shannon Nelson <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-23ixgbe: add ipsec register access routinesShannon Nelson5-0/+222
Add a few routines to make access to the ipsec registers just a little easier, and throw in the beginnings of an initialization. Signed-off-by: Shannon Nelson <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-23ixgbe: clean up ipsec definesShannon Nelson1-13/+7
Clean up the ipsec/macsec descriptor bit definitions to match the rest of the defines and file organization. Also recognise the bit-definition overlap in the error mask macro. Signed-off-by: Shannon Nelson <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-12ixgbe: Fix kernel-doc format warningsTony Nguyen12-39/+99
Recent checks added for formatting kernel-doc comments are causing warnings if W= is run with a non-zero value. This patch fixes function comments to resolve warnings when W=1 is used. Signed-off-by: Tony Nguyen <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-12ixgbe: Fix handling of macvlan Tx offloadAlexander Duyck2-10/+14
This update makes it so that we report the actual number of Tx queues via real_num_tx_queues but are still restricted to RSS on only the first pool by setting num_tc equal to 1. Doing this locks us into only having the ability to setup XPS on the queues in that pool, and only those queues should be used for transmitting anything other than macvlan traffic. Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-12ixgbe: avoid bringing rings up/down as macvlans are added/removedAlexander Duyck2-58/+72
This change makes it so that instead of bringing rings up/down for various we just update the netdev pointer for the Rx ring and set or clear the MAC filter for the interface. By doing it this way we can avoid a number of races and issues in the code as things were getting messy with the macvlan clean-up racing with the interface clean-up to bring the rings down on shutdown. With this change we opt to leave the rings owned by the PF interface for both Tx and Rx and just direct the packets once they are received to the macvlan netdev. Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-12ixgbe: Do not manipulate macvlan Tx queues when performing macvlan offloadAlexander Duyck2-108/+25
We should not be stopping/starting the upper devices Tx queues when handling a macvlan offload. Instead we should be stopping and starting traffic on our own queues. In order to prevent us from doing this I am updating the code so that we no longer change the queue configuration on the upper device, nor do we update the queue_index on our own device. Instead we can just use the queue index for our local device and not update the netdev in the case of the transmit rings. Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-12ixgbe/fm10k: Record macvlan stats instead of Rx queue for macvlan offloaded ↵Alexander Duyck1-2/+8
rings We shouldn't be recording the Rx queue on macvlan offloaded frames since the macvlan is normally brought up as a single queue device, and it will trigger warnings for RPS if we have recorded queue IDs larger than the "real_num_rx_queues" value recorded for the device. Instead we should be recording the macvlan statistics since we are bypassing the normal macvlan statistics that would have been generated by the receive path. Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-12ixgbe: Don't assume dev->num_tc is equal to hardware TC configAlexander Duyck6-27/+29
The code throughout ixgbe was assuming that dev->num_tc was populated and configured with the driver, when in fact this can be configured via mqprio without any hardware coordination other than restricting us to the real number of Tx queues we advertise. Instead of handling things this way we need to keep a local copy of the number of TCs in use so that we don't accidentally pull in the TC configuration from mqprio when it is configured in software mode. Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-12ixgbe: Default to 1 pool always being allocatedAlexander Duyck2-5/+3
We might as well configure the limit to default to 1 pool always for the interface. This accounts for the fact that the PF counts as 1 pool if SR-IOV is enabled, and in general we are always running in 1 pool mode when RSS or DCB is enabled as well, though we don't need to actually evaluate any of the VMDq features in those cases. Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-12ixgbe: Assume provided MAC filter has been verified by macvlanAlexander Duyck1-4/+8
The macvlan driver itself will validate the MAC address that is configured for a given interface. There is no need for us to verify it again. Instead we should be checking to verify that we actually allocate the filter and have not run out of resources to configure a MAC rule in our filter table. Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-09ixgbe: Drop l2_accel_priv data pointer from ring structAlexander Duyck2-11/+13
The l2 acceleration private pointer isn't needed in the ring struct. It isn't really used anywhere other than to test and see if we are supporting an offloaded macvlan netdev, and it is much easier to test netdev for not being ixgbe based to verify that. Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-09ixgbe: Use ring values to test for Tx pendingAlexander Duyck1-16/+4
This patch simplifies the check for Tx pending traffic and makes it more holistic as there being any difference between next_to_use and next_to_clean is much more informative than if head and tail are equal, as it is possible for us to either not update tail, or not be notified of completed work in which case next_to_clean would not be equal to head. In addition the simplification makes it so that we don't have to read hardware which allows us to drop a number of variables that were previously being used in the call. Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-09ixgbe: Fix limitations on macvlan so we can support up to 63 offloaded devicesAlexander Duyck4-43/+34
This change is a fix of the macvlan offload so that we correctly handle macvlan offloaded devices. Specifically we were configuring our limits based on the assumption that we were going to max out the RSS indices for every mode. As a result when we went to 15 or more macvlan interfaces we were forced into the 2 queue RSS mode on VFs even though they could have still supported 4. This change splits the logic up so that we limit either the total number of macvlan instances if DCB is enabled, or limit the number of RSS queues used per macvlan (instead of per pool) if SR-IOV is enabled. By doing this we can make best use of the part. In addition I have increased the maximum number of supported interfaces to 63 with one queue per offloaded interface as this more closely reflects the actual values supported by the interface. Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-09ixgbe: There is no need to update num_rx_pools in L2 fwd offloadAlexander Duyck2-4/+1
The num_rx_pools value is overwritten when we reinitialize the queue configuration. In reality we shouldn't need to be updating the value since it is redone every time we call into ixgbe_setup_tc so for now just drop the spots where we were incrementing or decrementing the value. Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-09ixgbe: Add support for macvlan offload RSS on X550 and clean-up pool handlingAlexander Duyck1-37/+25
In order for RSS to work on the macvlan pools of the X550 we need to populate the MRQC, RETA, and RSS key values for each pool. This patch makes it so that we now take care of that. In addition I have dropped the macvlan specific configuration of psrtype since it is redundant with the code that already exists for configuring this value. Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-09ixgbe: Perform reinit any time number of VFs changeAlexander Duyck1-16/+3
If the number of VFs are changed we need to reinitialize the part since the offset for the device and the number of pools will be incorrect. Without this change we can end up seeing Tx hangs and dropped Rx frames for incoming traffic. In addition we should drop the code that is arbitrarily changing the default pool and queue configuration. Instead we should wait until the port is reset and reconfigured via ixgbe_sriov_reinit. Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-09ixgbe: Fix interaction between SR-IOV and macvlan offloadAlexander Duyck1-7/+5
When SR-IOV was enabled the macvlan offload was configuring several filters with the wrong pool value. This would result in the macvlan interfaces not being able to receive traffic that had to pass over the physical interface. To fix it wrap the pool argument in the VMDQ_P macro which will add the necessary offset to get to the actual VMDq pool Signed-off-by: Alexander Duyck <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-09ixgbe: Remove an obsolete comment about ITRTonghao Zhang1-2/+0
The InterruptThrottleRate has been removed from ixgbe. Then Update the comment. Signed-off-by: Tonghao Zhang <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-09ixgbe: extend firmware version supportPaul Greenwalt7-14/+198
Extend FW version reporting by displaying information from the iSCSI or OEM block in the EEPROM. This will allow us to more accurately identify the FW. Signed-off-by: Paul Greenwalt <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-09ixgbe: advertise highest capable link speedPaul Greenwalt1-9/+8
On module insert advertise highest capable link speed. If module is capable of 10G, then advertise 10G, else advertise modules capable link speeds. Signed-off-by: Paul Greenwalt <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-09ixgbe: remove unused enum latency_rangeEmil Tantilov1-7/+0
This enum is no longer needed after commit: b4ded8327fe ("ixgbe: Update adaptive ITR algorithm") Signed-off-by: Emil Tantilov <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-09ixgbe: enable multicast on shutdown for WOLEmil Tantilov1-7/+7
Previously we only enabled the reception of multicast packets when wake on multicast is set, but we also need this to allow waking with IPv6 magic packets. Signed-off-by: Emil Tantilov <[email protected]> Tested-by: Andrew Bowers <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
2018-01-05ixgbe: setup xdp_rxq_infoJesper Dangaard Brouer3-1/+15
Driver hook points for xdp_rxq_info: * reg : ixgbe_setup_rx_resources() * unreg: ixgbe_free_rx_resources() Tested on actual hardware. V2: Fix ixgbe_set_ringparam, clear xdp_rxq_info in temp_ring Cc: [email protected] Cc: Jeff Kirsher <[email protected]> Cc: Alexander Duyck <[email protected]> Signed-off-by: Jesper Dangaard Brouer <[email protected]> Acked-by: John Fastabend <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]>
2017-12-06act_mirred: get rid of tcfm_ifindex from struct tcf_mirredCong Wang1-2/+4
tcfm_dev always points to the correct netdev and we already hold a refcnt, so no need to use tcfm_ifindex to lookup again. If we would support moving target netdev across netns, using pointer would be better than ifindex. This also fixes dumping obsolete ifindex, now after the target device is gone we just dump 0 as ifindex. Cc: Jiri Pirko <[email protected]> Cc: Jamal Hadi Salim <[email protected]> Signed-off-by: Cong Wang <[email protected]> Acked-by: Jiri Pirko <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.