| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/intel/igb/igb_main.c: In function ‘__igb_notify_dca’:
drivers/net/ethernet/intel/igb/igb_main.c:6694:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (dca_add_requester(dev) == 0) {
^
drivers/net/ethernet/intel/igb/igb_main.c:6701:2: note: here
case DCA_PROVIDER_REMOVE:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: "Gustavo A. R. Silva" <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Failed in read the HW register is very serious for igb/igc driver,
as its hw_addr will be set to NULL and cause the adapter be seen as
"REMOVED".
We saw the error only a few times in the MTBF test for suspend/resume,
but can hardly get any useful info to debug.
Adding WARN() so that we can get the necessary information about
where and how it happens, and use it for root causing and fixing
this "PCIe link lost issue"
This affects igb, igc.
Signed-off-by: Feng Tang <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Acked-by: Sasha Neftin <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
|
|
Update all users of eth_get_headlen to pass network device, fetch
network namespace from it and pass it down to the flow dissector.
This commit is a noop until administrator inserts BPF flow dissector
program.
Cc: Maxim Krasnyansky <[email protected]>
Cc: Saeed Mahameed <[email protected]>
Cc: Jeff Kirsher <[email protected]>
Cc: [email protected]
Cc: Yisen Zhuang <[email protected]>
Cc: Salil Mehta <[email protected]>
Cc: Michael Chan <[email protected]>
Cc: Igor Russkikh <[email protected]>
Signed-off-by: Stanislav Fomichev <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
|
|
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <[email protected]>
|
|
There are two reasons for this.
First, the xmit_more flag conceptually doesn't fit into the skb, as
xmit_more is not a property related to the skb.
Its only a hint to the driver that the stack is about to transmit another
packet immediately.
Second, it was only done this way to not have to pass another argument
to ndo_start_xmit().
We can place xmit_more in the softnet data, next to the device recursion.
The recursion counter is already written to on each transmit. The "more"
indicator is placed right next to it.
Drivers can use the netdev_xmit_more() helper instead of skb->xmit_more
to check the "more packets coming" hint.
skb->xmit_more is retained (but always 0) to not cause build breakage.
This change takes care of the simple s/skb->xmit_more/netdev_xmit_more()/
conversions. Remaining drivers are converted in the next patches.
Suggested-by: Eric Dumazet <[email protected]>
Signed-off-by: Florian Westphal <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The runtime_suspend device callbacks are not supposed to save
configuration state or change the power state. Commit fb29f76cc566
("igb: Fix an issue that PME is not enabled during runtime suspend")
changed the driver to not save configuration state during runtime
suspend, however the driver callback still put the device into a
low-power state. This causes a warning in the pci pm core and results in
pci_pm_runtime_suspend not calling pci_save_state or pci_finish_runtime_suspend.
Fix this by not changing the power state either, leaving that to pci pm
core, and make the same change for suspend callback as well.
Also move a couple of defines into the appropriate header file instead
of inline in the .c file.
Fixes: fb29f76cc566 ("igb: Fix an issue that PME is not enabled during runtime suspend")
Signed-off-by: Arvind Sankar <[email protected]>
Reviewed-by: Kai-Heng Feng <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
There are some lines that have indentation issues, fix these
Signed-off-by: Colin Ian King <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
igb sets different WoL settings in system suspend callback and runtime
suspend callback.
The suspend direct complete optimization leaves igb in runtime suspended
state with wrong WoL setting during system suspend.
To fix this, we need to disable suspend direct complete optimization to
let igb always use suspend callback to set correct WoL during system
suspend.
Signed-off-by: Kai-Heng Feng <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
According to comments in <linux/netdevice.h> we should return either >0
or -errno from ->ndo_set_features() if changing dev->features by itself.
Return 1 in such places to notify netdev_update_features() about applied
changes in dev->features.
Signed-off-by: Serhey Popovych <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
size = struct_size(instance, entry, count);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch wraps the dissector key and mask - that flower uses to
represent the matching side - around the flow_match structure.
To avoid a follow up patch that would edit the same LoCs in the drivers,
this patch also wraps this new flow match structure around the flow rule
object. This new structure will also contain the flow actions in follow
up patches.
This introduces two new interfaces:
bool flow_rule_match_key(rule, dissector_id)
that returns true if a given matching key is set on, and:
flow_rule_match_XYZ(rule, &match);
To fetch the matching side XYZ into the match container structure, to
retrieve the key and the mask with one single call.
Signed-off-by: Pablo Neira Ayuso <[email protected]>
Acked-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
With recent changes, need to bump the driver version to reflect the
changes.
Signed-off-by: Todd Fujinaka <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Completely minor snmp doc conflict.
Signed-off-by: David S. Miller <[email protected]>
|
|
Drivers may not be able to support certain FDB entries, and an error
code is insufficient to give clear hints as to the reasons of rejection.
In order to make it possible to communicate the rejection reason, extend
ndo_fdb_add() with an extack argument. Adapt the existing
implementations of ndo_fdb_add() to take the parameter (and ignore it).
Pass the extack parameter when invoking ndo_fdb_add() from rtnl_fdb_add().
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This reverts commit 59361316afcb08569af21e1af83e89c7051c055a.
Due to problems found in additional testing, this causes an illegal
context switch in the RCU read-side critical section.
CC: Dave Jones <[email protected]>
CC: Cong Wang <[email protected]>
CC: Jan Jablonsky <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
I210 ethernet card doesn't wakeup when a cable gets plugged. It's
because its PME is not set.
Since commit 42eca2302146 ("PCI: Don't touch card regs after runtime
suspend D3"), if the PCI state is saved, pci_pm_runtime_suspend() stops
calling pci_finish_runtime_suspend(), which enables the PCI PME.
To fix the issue, let's not to save PCI states when it's runtime
suspend, to let the PCI subsystem enables PME.
Fixes: 42eca2302146 ("PCI: Don't touch card regs after runtime suspend D3")
Signed-off-by: Kai-Heng Feng <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Section 4.5.9 of the datasheet says that the total size of all packet
buffers combined (TxPB 0 + 1 + 2 + 3 + RxPB + BMC2OS + OS2BMC) must not
exceed 60KB. Today we are configuring a total of 62KB, so reduce the
RxPB from 32KB to 30KB in order to respect that.
The choice of changing RxPBSIZE here is mainly because it seems more
correct to give more priority to the transmit packet buffers over the
receiver ones when running in Qav mode. Also, the BMC2OS and OS2BMC
sizes are already too short.
Signed-off-by: Jesus Sanchez-Palencia <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This change is based off of the work and suggestion of Jan Jablonsky
<[email protected]>.
The Watchdog workqueue in igb driver is scheduled every 2s for each
network interface. That includes updating a statistics protected by
spinlock. Function igb_update_stats in this case will be protected
against preemption. According to number of a statistics registers
(cca 60), processing this function might cause additional cpu load
on CPU0.
In case of statistics spinlock may be replaced with mutex, which
reduce latency on CPU0.
CC: Bernhard Kaindl <[email protected]>
CC: Jan Jablonsky <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch fixes the variable 'phy_word' may be used uninitialized.
Signed-off-by: Yunjian Wang <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
While reviewing code, I noticed that Eric Dumazet recommends that
drivers check the return code of napi_complete_done, and use that
to decide to enable interrupts or not when exiting poll. One of
the Intel drivers was already fixed (ixgbe).
Upon looking at the Intel drivers as a whole, we are handling our
polling and NAPI exit in a few different ways based on whether we
have multiqueue and whether we have Tx cleanup included. Several
drivers had the bug of exiting NAPI with return 0, which appears
to mess up the accounting in the stack.
Consolidate all the NAPI routines to do best known way of exiting
and to just mostly look like each other.
1) check return code of napi_complete_done to control interrupt enable
2) return the actual amount of work done.
3) return budget immediately if need NAPI poll again
Tested the changes on e1000e with a high interrupt rate set, and
it shows about an 8% reduction in the CPU utilization when busy
polling because we aren't re-enabling interrupts when we're about
to be polled.
Signed-off-by: Jesse Brandeburg <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Reviewed-by: Jacob Keller <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
The line continuation unintentionally adds whitespace so
instead use a coalesced format to remove the whitespace.
Miscellanea:
o Use a more typical style for ternaries and arguments
for this logging message
Signed-off-by: Joe Perches <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Acked-by: Vinicius Costa Gomes <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
|
|
This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.
Cc: Richard Cochran <[email protected]>
Cc: Jacob Keller <[email protected]>
Cc: Jeff Kirsher <[email protected]>
Signed-off-by: Miroslav Lichvar <[email protected]>
Acked-by: Jeff Kirsher <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There's a new flag for setting WoL filters that is only
enabled on one manufacturer's NICs, and it's not ours. Fail
with EOPNOTSUPP.
Signed-off-by: Todd Fujinaka <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Many of the Intel Ethernet drivers call skb_tx_timestamp() earlier than
necessary. Move the calls to this function to the latest point possible,
just prior to notifying hardware of the new Tx packet when we bump the
tail register.
This affects i40e, iavf, igb, igc, and ixgbe.
The e100, e1000, e1000e, fm10k, and ice drivers already call the
skb_tx_timestamp() function just prior to indicating the Tx packet to
hardware, so they do not need to be changed.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
The timecounter needs to be updated at least once per ~550 seconds in
order to avoid a 40-bit SYSTIM timestamp to be misinterpreted as an old
timestamp.
Since commit 500462a9de65 ("timers: Switch to a non-cascading wheel"),
scheduling of delayed work seems to be less accurate and a requested
delay of 540 seconds may actually be longer than 550 seconds. Also, the
PHC may be adjusted to run up to 6% faster than real time and the system
clock up to 10% slower. Shorten the delay to 360 seconds to be sure the
timecounter is updated in time.
This fixes an issue with HW timestamps on 82580/I350/I354 being off by
~1100 seconds for few seconds every ~9 minutes.
Cc: Thomas Gleixner <[email protected]>
Signed-off-by: Miroslav Lichvar <[email protected]>
Acked-by: Jacob Keller <[email protected]>
Acked-by: Richard Cochran <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
The timecounter needs to be updated at least once per ~550 seconds in
order to avoid a 40-bit SYSTIM timestamp to be misinterpreted as an old
timestamp.
Since commit 500462a9d ("timers: Switch to a non-cascading wheel"),
scheduling of delayed work seems to be less accurate and a requested
delay of 540 seconds may actually be longer than 550 seconds. Shorten
the delay to 480 seconds to be sure the timecounter is updated in time.
This fixes an issue with HW timestamps on 82580/I350/I354 being off by
~1100 seconds for few seconds every ~9 minutes.
Cc: Jacob Keller <[email protected]>
Cc: Richard Cochran <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Signed-off-by: Miroslav Lichvar <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
|
|
After bfcb79fca19d ("PCI/ERR: Run error recovery callbacks for all affected
devices"), AER errors are always cleared by the PCI core and drivers don't
need to do it themselves.
Remove calls to pci_cleanup_aer_uncorrect_error_status() from device
driver error recovery functions.
Signed-off-by: Oza Pawandeep <[email protected]>
[bhelgaas: changelog, remove PCI core changes, remove unused variables]
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <[email protected]>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
igb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <[email protected]>
Cc: Jeff Kirsher <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
We recently updated all our SPDX identifiers to correctly
indicate our net/ethernet/intel/* drivers were always released
and intended to be released under GPL v2, but the MODULE_LICENSE
declaration was never updated.
Fix the MODULE_LICENSE to be GPL v2, for all our drivers.
Signed-off-by: Jesse Brandeburg <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
igb_integrated_phy_loopback() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
igb_sw_init() is never called in atomic context.
It calls kzalloc() and kcalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
On i210, Launchtime (TxTime) requires the usage of an "Advanced
Transmit Context Descriptor" for retrieving the timestamp of a packet.
The igb driver correctly builds such descriptor on the segmentation
flow (i.e. igb_tso()) or on the checksum one (i.e. igb_tx_csum()), but the
feature is broken for AF_PACKET if the IGB_TX_FLAGS_VLAN is not set,
which happens due to an early return on igb_tx_csum().
This flag is only set by the kernel when a VLAN interface is used,
thus we can't just rely on it. Here we are fixing this issue by checking
if launchtime is enabled for the current tx_ring before performing the
early return.
Signed-off-by: Jesus Sanchez-Palencia <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
- Decode AER errors with names similar to "lspci" (Tyler Baicar)
- Expose AER statistics in sysfs (Rajat Jain)
- Clear AER status bits selectively based on the type of recovery (Oza
Pawandeep)
- Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST (Alexandru
Gagniuc)
- Don't clear AER status bits if we're using the "Firmware-First"
strategy where firmware owns the registers (Alexandru Gagniuc)
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
- Defer DPC event handling to work queue (Keith Busch)
- Use threaded IRQ for DPC bottom half (Keith Busch)
- Print AER status while handling DPC events (Keith Busch)
- Work around IDT switch ACS Source Validation erratum (James
Puthukattukaran)
- Emit diagnostics for all cases of PCIe Link downtraining (Links
operating slower than they're capable of) (Alexandru Gagniuc)
- Skip VFs when configuring Max Payload Size (Myron Stowe)
- Reduce Root Port Max Payload Size if necessary when hot-adding a
device below it (Myron Stowe)
- Simplify SHPC existence/permission checks (Bjorn Helgaas)
- Remove hotplug sample skeleton driver (Lukas Wunner)
- Convert pciehp to threaded IRQ handling (Lukas Wunner)
- Improve pciehp tolerance of missed events and initially unstable
links (Lukas Wunner)
- Clear spurious pciehp events on resume (Lukas Wunner)
- Add pciehp runtime PM support, including for Thunderbolt controllers
(Lukas Wunner)
- Support interrupts from pciehp bridges in D3hot (Lukas Wunner)
- Mark fall-through switch cases before enabling -Wimplicit-fallthrough
(Gustavo A. R. Silva)
- Move DMA-debug PCI init from arch code to PCI core (Christoph
Hellwig)
- Fix pci_request_irq() usage of IRQF_ONESHOT when no handler is
supplied (Heiner Kallweit)
- Unify PCI and DMA direction #defines (Shunyong Yang)
- Add PCI_DEVICE_DATA() macro (Andy Shevchenko)
- Check for VPD completion before checking for timeout (Bert Kenward)
- Limit Netronome NFP5000 config space size to work around erratum
(Jakub Kicinski)
- Set IRQCHIP_ONESHOT_SAFE for PCI MSI irqchips (Heiner Kallweit)
- Document ACPI description of PCI host bridges (Bjorn Helgaas)
- Add "pci=disable_acs_redir=" parameter to disable ACS redirection for
peer-to-peer DMA support (we don't have the peer-to-peer support yet;
this is just one piece) (Logan Gunthorpe)
- Clean up devm_of_pci_get_host_bridge_resources() resource allocation
(Jan Kiszka)
- Fixup resizable BARs after suspend/resume (Christian König)
- Make "pci=earlydump" generic (Sinan Kaya)
- Fix ROM BAR access routines to stay in bounds and check for signature
correctly (Rex Zhu)
- Add DMA alias quirk for Microsemi Switchtec NTB (Doug Meyer)
- Expand documentation for pci_add_dma_alias() (Logan Gunthorpe)
- To avoid bus errors, enable PASID only if entire path supports
End-End TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD
Controller (Bjorn Helgaas)
- Remove Xilinx AXI-PCIe host bridge arch dependency (Palmer Dabbelt)
- Remove Aardvark outbound window configuration (Evan Wang)
- Fix Aardvark bridge window sizing issue (Zachary Zhang)
- Convert Aardvark to use pci_host_probe() to reduce code duplication
(Thomas Petazzoni)
- Correct the Cadence cdns_pcie_writel() signature (Alan Douglas)
- Add Cadence support for optional generic PHYs (Alan Douglas)
- Add Cadence power management ops (Alan Douglas)
- Remove redundant variable from Cadence driver (Colin Ian King)
- Add Kirin MSI support (Xiaowei Song)
- Drop unnecessary root_bus_nr setting from exynos, imx6, keystone,
armada8k, artpec6, designware-plat, histb, qcom, spear13xx (Shawn
Guo)
- Move link notification settings from DesignWare core to individual
drivers (Gustavo Pimentel)
- Add endpoint library MSI-X interfaces (Gustavo Pimentel)
- Correct signature of endpoint library IRQ interfaces (Gustavo
Pimentel)
- Add DesignWare endpoint library MSI-X callbacks (Gustavo Pimentel)
- Add endpoint library MSI-X test support (Gustavo Pimentel)
- Remove unnecessary GFP_ATOMIC from Hyper-V "new child" allocation
(Jia-Ju Bai)
- Add more devices to Broadcom PAXC quirk (Ray Jui)
- Work around corrupted Broadcom PAXC config space to enable SMMU and
GICv3 ITS (Ray Jui)
- Disable MSI parsing to work around broken Broadcom PAXC logic in some
devices (Ray Jui)
- Hide unconfigured functions to work around a Broadcom PAXC defect
(Ray Jui)
- Lower iproc log level to reduce console output during boot (Ray Jui)
- Fix mobiveil iomem/phys_addr_t type usage (Lorenzo Pieralisi)
- Fix mobiveil missing include file (Lorenzo Pieralisi)
- Add mobiveil Kconfig/Makefile support (Lorenzo Pieralisi)
- Fix mvebu I/O space remapping issues (Thomas Petazzoni)
- Use generic pci_host_bridge in mvebu instead of ARM-specific API
(Thomas Petazzoni)
- Whitelist VMD devices with fast interrupt handlers to avoid sharing
vectors with slow handlers (Keith Busch)
* tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (153 commits)
PCI/AER: Don't clear AER bits if error handling is Firmware-First
PCI: Limit config space size for Netronome NFP5000
PCI/MSI: Set IRQCHIP_ONESHOT_SAFE for PCI-MSI irqchips
PCI/VPD: Check for VPD access completion before checking for timeout
PCI: Add PCI_DEVICE_DATA() macro to fully describe device ID entry
PCI: Match Root Port's MPS to endpoint's MPSS as necessary
PCI: Skip MPS logic for Virtual Functions (VFs)
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Check for PCIe Link downtraining
PCI: Add ACS Redirect disable quirk for Intel Sunrise Point
PCI: Add device-specific ACS Redirect disable infrastructure
PCI: Convert device-specific ACS quirks from NULL termination to ARRAY_SIZE
PCI: Add "pci=disable_acs_redir=" parameter for peer-to-peer support
PCI: Allow specifying devices using a base bus and path of devfns
PCI: Make specifying PCI devices in kernel parameters reusable
PCI: Hide ACS quirk declarations inside PCI core
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: mvebu: Drop bogus comment above mvebu_pcie_map_registers()
...
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114800 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114799 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 200521 ("Missing break in switch")
Addresses-Coverity-ID: 114797 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The igb driver doesn't need anything provided by pci-aspm.h, so remove
the unnecessary include of it.
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Sinan Kaya <[email protected]>
Acked-by: Alexander Duyck <[email protected]>
Acked-by: Jeff Kirsher <[email protected]>
|
|
igb writes to doorbells to post transmit and receive descriptors;
after writing descriptors to memory but before writing to doorbells,
use dma_wmb() rather than wmb(). wmb() is more heavyweight than
necessary before doorbell writes.
On x86, this avoids SFENCEs before doorbell writes in both the
tx and rx refill paths.
Signed-off-by: Venkatesh Srinivas <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
This patch reverts two previous applied patches to fix an issue
that appeared when using SGMII based SFP modules. In the current
state the driver will try to reset the PHY before obtaining the
phy_addr of the SGMII attached PHY. That leads to an error in
e1000_write_phy_reg_sgmii_82575. Causing the initialization to
fail:
igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
igb: Copyright (c) 2007-2014 Intel Corporation.
igb: probe of ????:??:??.? failed with error -3
The patches being reverted are:
commit 182785335447957409282ca745aa5bc3968facee
Author: Aaron Sierra <[email protected]>
Date: Tue Nov 29 10:03:56 2016 -0600
igb: reset the PHY before reading the PHY ID
commit 440aeca4b9858248d8f16d724d9fa87a4f65fa33
Author: Matwey V Kornilov <[email protected]>
Date: Thu Nov 24 13:32:48 2016 +0300
igb: Explicitly select page 0 at initialization
The first reverted patch directly causes the problem mentioned above.
In case of SGMII the phy_addr is not known at this point and will
only be obtained by 'igb_get_phy_id_82575' further down in the code.
The second removed patch selects forces selection of page 0 in the
PHY. Something that the reset tries to address as well.
As pointed out by Alexander Duzck, the patch below fixes the same
issue but in the proper location:
commit 4e684f59d760a2c7c716bb60190783546e2d08a1
Author: Chris J Arges <[email protected]>
Date: Wed Nov 2 09:13:42 2016 -0500
igb: Workaround for igb i210 firmware issue
Reverts: 440aeca4b9858248d8f16d724d9fa87a4f65fa33.
Reverts: 182785335447957409282ca745aa5bc3968facee.
Signed-off-by: Christian Grönke <[email protected]>
Reviewed-by: Alexander Duyck <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|
|
Implement HW offload support for SO_TXTIME through igb's Launchtime
feature. This is done by extending igb_setup_tc() so it supports
TC_SETUP_QDISC_ETF and configuring i210 so time based transmit
arbitration is enabled.
The FQTSS transmission mode added before is extended so strict
priority (SP) queues wait for stream reservation (SR) ones.
igb_config_tx_modes() is extended so it can support enabling/disabling
Launchtime following the previous approach used for the credit-based
shaper (CBS).
As the previous flow, FQTSS transmission mode is enabled automatically
by the driver once Launchtime (or CBS, as before) is enabled.
Similarly, it's automatically disabled when the feature is disabled
for the last queue that had it setup on.
The driver just consumes the transmit times from the skbuffs directly,
so no special handling is done in case an 'invalid' time is provided.
We assume this has been handled by the ETF qdisc already.
Signed-off-by: Jesus Sanchez-Palencia <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Currently, skb_tx_timestamp() is being called before the Tx
descriptors are prepared in igb_xmit_frame_ring(), which happens
during either the igb_tso() or igb_tx_csum() calls.
Given that now the skb->tstamp might be used to carry the timestamp
for SO_TXTIME, we must only call skb_tx_timestamp() after the
information has been copied into the Tx descriptors.
Signed-off-by: Jesus Sanchez-Palencia <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Split code into a separate function (igb_offload_apply()) that will be
used by ETF offload implementation.
Signed-off-by: Jesus Sanchez-Palencia <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Currently the data transmission arbitration algorithm - DataTranARB
field on TQAVCTRL reg - is always set to CBS when the Tx mode is
changed from legacy to 'Qav' mode.
Make that configuration a bit more granular in preparation for the
upcoming Launchtime enabling patches, since CBS and Launchtime can be
enabled separately. That is achieved by moving the DataTranARB setup
to igb_config_tx_modes() instead.
Similarly, when disabling CBS we must check if it has been disabled
for all queues, and clear the DataTranARB accordingly.
Signed-off-by: Jesus Sanchez-Palencia <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|