| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add a new ice_ptp.c file for holding the basic PTP clock interface
functions. If the device supports PTP, call the new ice_ptp_init and
ice_ptp_release functions where appropriate.
If the function owns the hardware resource associated with the PTP
hardware clock, register with the PTP_1588_CLOCK infrastructure to
allocate a new clock object that represents the device hardware clock.
Implement basic functionality for reading and setting the clock time,
performing clock adjustments, and adjusting the clock frequency.
Future changes will introduce functionality for handling related
features including Tx and Rx timestamps.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Depending on the device configuration, the ice hardware may share the
PTP hardware clock timer between multiple PFs. Each PF is informed by
firmware during initialization of the PTP timer association.
When bringing up PTP, only the PFs which own the timer shall allocate
a PTP hardware clock. Other PFs associated with that timer must report
the correct PTP clock index in order to allow userspace software the
ability to know which ports are connected to the same clock.
To support this, the firmware has driver shared parameters. These
parameters enable one PF to write the clock index into firmware, and
have other PFs read the associated value out. This enables the driver to
have only a single PF allocate and control the device timer registers,
while other PFs associated with that timer can report the correct clock
in the ETHTOOL_GET_TS_INFO report.
Add support for the necessary admin queue commands to enable reading and
writing of the driver shared parameters. This will be used in a future
change to enable sharing the PTP clock index between PF drivers.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The device firmware reports PTP clock capabilities to each PF during
initialization. This includes various information for both the overall
device and the individual function, including
For functions:
* whether this function has timesync enabled
* whether this function owns one of the 2 possible clock timers, and
which one
* which timer the function is associated with
* the clock frequency, if the device supports multiple clock frequencies
* The GPIO pin association for the timer owned by this PF, if any
For the device:
* Which PF owns timer 0, if any
* Which PF owns timer 1, if any
* whether timer 0 is enabled
* whether timer 1 is enabled
Extract the bits from the capabilities information reported by firmware
and store them in the device and function capability structures.o
This information will be used in a future change to have the function
driver enable PTP hardware clock support.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
In order to support certain device features, including enabling the PTP
hardware clock, the ice driver needs to control some registers on the
device PHY.
These registers are accessed by sending sideband messages. For some
hardware, these messages must be sent over the device admin queue, while
other hardware has a dedicated control queue for the sideband messages.
Add the neighbor device message structure for sending a message to the
neighboring device. Where supported, initialize the sideband control
queue and handle cleanup.
Add a wrapper function for sending sideband control queue messages that
read or write a neighboring device register.
Because some devices send sideband messages over the AdminQ, also
increase the length of the admin queue to allow more messages to be
queued up. This is important because the sideband messages add
additional pressure on the AQ usage.
This support will be used in following patches to enable support for
CONFIG_1588_PTP_CLOCK.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Determine whether an unsupported power configuration is preventing link
establishment by storing and checking the link_cfg_err_byte. Print error
messages when module power levels are unsupported. Also add a new flag
bit to prevent spamming said error messages.
Co-developed-by: Jeb Cramer <[email protected]>
Signed-off-by: Jeb Cramer <[email protected]>
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Add implementations for supporting iidc operations for device operation
such as allocation of resources and event notifications.
Signed-off-by: Dave Ertman <[email protected]>
Signed-off-by: Shiraz Saleem <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Probe the device's capabilities to see if it supports RDMA. If so, allocate
and reserve resources to support its operation; populate structures with
initial values.
Signed-off-by: Dave Ertman <[email protected]>
Signed-off-by: Shiraz Saleem <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Beyond a specific version of firmware, there is no need to provide
override values to the firmware when setting PHY capabilities. In this
case, we do not need to indicate whether we're in Strict or Lenient Link
Mode.
In the case of translating capabilities to the configuration structure,
the module compliance enforcement is already correctly set by firmware,
so the extra code block is redundant.
Signed-off-by: Jeb Cramer <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Recent firmware supports a new "get PHY capabilities" mode
ICE_AQC_REPORT_DFLT_CFG which makes it unnecessary for the driver
to track and apply NVM based default link overrides.
If FW AQ API version supports it, use Report Default Configuration.
Add check function for Report Default Configuration support and update
accordingly.
Also change adv_phy_type_[lo|hi] to advert_phy_type[lo|hi] for
clarity.
Co-developed-by: Mateusz Pacuszka <[email protected]>
Signed-off-by: Mateusz Pacuszka <[email protected]>
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
For get PHY abilities AQ, the specification defines "report modes"
as "with media", "without media" and "active configuration". For
clarity, rename macros to align with the specification.
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Retry sending some AQ commands, as result of EBUSY AQ error.
ice_aqc_opc_get_link_topo
ice_aqc_opc_lldp_stop
ice_aqc_opc_lldp_start
ice_aqc_opc_lldp_filter_ctrl
This change follows the latest guidelines from HW team. It is
better to retry the same AQ command several times, as the result
of EBUSY, instead of returning error to the caller right away.
Signed-off-by: Chinh T Cao <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Update ice_aq_get_rss_lut() and ice_aq_set_rss_lut() to take a new
structure ice_aq_get_set_rss_params instead of passing individual
parameters. This is done for 2 reasons:
1. Reduce the number of parameters passed to the functions.
2. Reduce the amount of change required if the arguments ever need to be
updated in the future.
Also, reduce duplicate code that was checking for an invalid vsi_handle
and lut parameter by moving the checks to the lower level
__ice_aq_get_set_rss_lut().
Signed-off-by: Brett Creeley <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Commit a012dca9f7a2 ("ice: add ethtool -m support for reading i2c eeprom
modules") unnecessarily added the ICE_AQ_FLAG_BUF flag to the descriptor
when sending the indirect Read/Write SFF EEPROM AQ command. The flag is
already added later in the code flow for all indirect AQ commands, i.e.
commands that provide an additional data buffer.
Signed-off-by: Bruce Allan <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Fix the order of number of array members and member size parameters in a
*calloc() call.
Fixes: b3c3890489f6 ("ice: avoid unnecessary single-member variable-length structs")
Signed-off-by: Bruce Allan <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Correct reported warnings for "warning: expecting prototype for ...
Prototype was for ... instead"
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
|
|
Casting a void * rvalue in an assignment is unnecessary in C; remove the
casts.
Signed-off-by: Bruce Allan <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The core clock frequency is currently hardcoded at 446 MHz for the RL
profile calculations. This causes issues since not all devices use that
clock frequency. Read the GLGEN_CLKSTAT_SRC register to determine which PSM
clock frequency is selected. This ensures that the rate limiter profile
calculations will be correct.
Signed-off-by: Ben Shelton <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Create set scheduler aggregator node and move for VSIs into respective
scheduler node. Max children per aggregator node is 64.
There are two types of aggregator node(s) created.
1. dedicated node for PF and _CTRL VSIs
2. dedicated node(s) for VFs.
As part of reset and rebuild, aggregator nodes are recreated and VSIs
are moved to respective aggregator node.
Having related VSIs in respective tree avoid starvation between PF and VF
w.r.t Tx bandwidth.
Co-developed-by: Tarun Singh <[email protected]>
Signed-off-by: Tarun Singh <[email protected]>
Co-developed-by: Victor Raj <[email protected]>
Signed-off-by: Victor Raj <[email protected]>
Co-developed-by: Anirudh Venkataramanan <[email protected]>
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Signed-off-by: Kiran Patil <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
There is an issue with some NVMs where an already existent LLDP
filter is blocking the creation of a filter to allow LLDP packets
to be redirected to the default VSI for the interface. This is
blocking all LLDP functionality based in the kernel when the FW
LLDP agent is disabled (e.g. software based DCBx).
Implement the new AQ command to allow adding VSI destinations to
existent filters on NVM versions that support the new command.
The new lldp_fltr_ctrl AQ command supports Rx filters only, so the
code flow for adding filters to disable Tx of control frames will
remain intact.
Signed-off-by: Dave Ertman <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Use the flex_array_size() helper with the recently added flexible array
members in structures.
Signed-off-by: Bruce Allan <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
When printing messages with ice_debug, align the printed string to the
origin line of the message in order to ease debugging and tracking
messages back to their source.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The driver is able to override the firmware when it comes to supporting
a more lenient link mode. This feature was limited to E810 devices. It
is now extended to E82X devices.
Signed-off-by: Jeb Cramer <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
There are times when the driver shouldn't return an error when the Get
PHY abilities AQ command (0x0600) returns an error. Instead the driver
should log that the error occurred and continue on. This allows the
driver to load even though the AQ command failed. The user can then
later determine the reason for the failure and correct it.
Signed-off-by: Paul M Stillwell Jr <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
If the driver initializes in safe mode, it will call
ice_set_safe_mode_caps. This results in clearing the capabilities
structures, in order to set them up for operating in safe mode, ensuring
many features are disabled.
This has a side effect of also clearing the capability bits that relate
to NVM update. The result is that the device driver will not indicate
support for unified update, even if the firmware is capable.
Fix this by adding the relevant capability fields to the list of values
we preserve. To simplify the code, use a common_cap structure instead of
a handful of local variables. To reduce some duplication of the
capability name, introduce a couple of macros used to restore the
capabilities values from the cached copy.
Fixes: de9b277ee032 ("ice: Add support for unified NVM update flow capability")
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Brijesh Behera <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
This is a collection of minor fixes including typos, white space, and
style. No functional changes.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
|
|
The grst_delay variable in ice_check_reset contains the maximum time
(in 100 msec units) that the driver will wait for a reset event to
transition to the Device Active state. The value is the sum of three
separate components:
1) The maximum time it may take for the firmware to process its
outstanding command before handling the reset request.
2) The value in RSTCTL.GRSTDEL (the delay firmware inserts between first
seeing the driver reset request and the actual hardware assertion).
3) The maximum expected reset processing time in hardware.
Referring to this total time as "grst_delay" is misleading and
potentially confusing to someone checking the code and cross-referencing
the hardware specification.
Fix this by renaming the variable to "grst_timeout", which is more
descriptive of its actual use.
Signed-off-by: Nick Nunley <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
For the FW logging info AQ command, we currently set the ICE_AQ_FLAG_RD
in order to work around a FW issue. This issue has been fixed so remove the
workaround.
Signed-off-by: Ben Shelton <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
By default the queues are configured in legacy mode. The default
BW settings for legacy/advanced modes are different. The existing
code was using the advanced mode default value of 1 which was
incorrect. This caused the unbalanced BW sharing among siblings.
The recommended default value is applied.
Signed-off-by: Tarun Singh <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
There is a bug where the LFC settings are not being preserved
through a link event. The registers in question are the ones
that are touched (and restored) when a set_local_mib AQ command
is performed.
On a link-up event, make sure that a set_local_mib is being
performed.
Move the function ice_aq_set_lldp_mib() from the DCB specific
ice_dcb.c to ice_common.c so that the driver always has access
to this AQ command.
Signed-off-by: Dave Ertman <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Use the newly added pldmfw library to implement device flash update for
the Intel ice networking device driver. This support uses the devlink
flash update interface.
The main parts of the flash include the Option ROM, the netlist module,
and the main NVM data. The PLDM firmware file contains modules for each
of these components.
Using the pldmfw library, the provided firmware file will be scanned for
the three major components, "fw.undi" for the Option ROM, "fw.mgmt" for
the main NVM module containing the primary device firmware, and
"fw.netlist" containing the netlist module.
The flash is separated into two banks, the active bank containing the
running firmware, and the inactive bank which we use for update. Each
module is updated in a staged process. First, the inactive bank is
erased, preparing the device for update. Second, the contents of the
component are copied to the inactive portion of the flash. After all
components are updated, the driver signals the device to switch the
active bank during the next EMP reset (which would usually occur during
the next reboot).
Although the firmware AdminQ interface does report an immediate status
for each command, the NVM erase and NVM write commands receive status
asynchronously. The driver must not continue writing until previous
erase and write commands have finished. The real status of the NVM
commands is returned over the receive AdminQ. Implement a simple
interface that uses a wait queue so that the main update thread can
sleep until the completion status is reported by firmware. For erasing
the inactive banks, this can take quite a while in practice.
To help visualize the process to the devlink application and other
applications based on the devlink netlink interface, status is reported
via the devlink_flash_update_status_notify. While we do report status
after each 4k block when writing, there is no real status we can report
during erasing. We simply must wait for the complete module erasure to
finish.
With this implementation, basic flash update for the ice hardware is
supported.
Signed-off-by: Jacob Keller <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
After a flash update, the pending status of the update can be determined
from the device capabilities.
Read the appropriate device capability and store whether there is
a pending update awaiting a reboot.
Signed-off-by: Jacob Keller <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Extends function parsing response from Discover Device
Capability AQC to check if the device supports unified NVM update flow.
Signed-off-by: Jacek Naczyk <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There isn't a case for 1G SGMII in ice_get_media_type() so add
the handling for it.
Also handle the special case where some direct attach
cables may report that they support 1G SGMII, but
that is erroneous since SGMII is supposed to be a
backplane media type (between a MAC and a PHY). If
the driver doesn't handle this special case then a
user could see the 'Port' in ethtool change from
'Direct attach Copper' to 'Backplane' when they have
forced the speed to 1G, but the cable hasn't changed.
Lastly, change ice_aq_get_phy_caps() to save the
module_type info if the function was called with
ICE_AQC_REPORT_TOPO_CAP. This call uses the media
information to populate the module_type. If no
media is present then the values in module_type
will be 0.
Signed-off-by: Paul M Stillwell Jr <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Report AOC types as fiber instead of unknown.
Signed-off-by: Doug Dziggel <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Add AQC get link topology handle support. This is needed to determine
Direct Attach (DA) or backplane media type for PHY types that support
either. Get link topology handle cage node type request can be used to
determine if a cage is present or not. If a cage is present for PHY
types that supports both DA and backplane media type, then the media
type is DA, else the media type is backplane.
Signed-off-by: Paul Greenwalt <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Rename the low_power_ctrl field to low_power_ctrl_an to be properly
descriptive of it being an autoneg field.
Signed-off-by: Lev Faerman <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Firmware now reports AN28, AN32, and AN73. Add a helper and check these new
values and report PHY autoneg capability.
Signed-off-by: Paul Greenwalt <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Add debug logs for ice_aq_get_phy_caps(), and format
ice_aq_set_phy_cfg() and ice_aq_get_link_info() debug logs to make them
more readable.
Signed-off-by: Paul Greenwalt <[email protected]>
Signed-off-by: Paul M Stillwell Jr <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Adds functions to check for link override firmware support and get
the override settings for a port. The previously supported/default link
mode was strict mode.
In strict mode link is configured based on get PHY capabilities PHY types
with media.
Lenient mode is now the default link mode. In lenient mode the link is
configured based on get PHY capabilities PHY types without media. This
allows the user to configure link that the media does not report. Limit the
minimum supported link mode to 25G for devices that support 100G, and 1G
for devices that support less than 100G.
Default override is only supported in lenient mode. If default override
is supported and enabled, then default override values are used for
configuring speed and FEC. Default override provide persistent link
settings in the NVM.
Signed-off-by: Paul Greenwalt <[email protected]>
Signed-off-by: Evan Swanson <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
After the transition from no media to media FW will clear the
set-phy-cfg data set by the user. Save initial PHY settings and any
settings later requested by the user and use that data to restore PHY
settings on media insertion. Since PHY configuration is now being stored,
replace calls that were calling FW to get the configuration with the saved
copy.
Signed-off-by: Paul Greenwalt <[email protected]>
Signed-off-by: Chinh T Cao <[email protected]>
Signed-off-by: Paul M Stillwell Jr <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The call to ice_cfg_phy_fec() requires the caller to perform certain
actions before calling it. Instead of imposing these preconditions move
the operations into the function and perform them ourselves.
Also, fix some style issues in nearby touched code.
Signed-off-by: Paul Greenwalt <[email protected]>
Signed-off-by: Chinh T Cao <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Create a helper function for configuring requested flow control so that it
can be utilized by other functions looking to configure flow control
settings. Utilize the existing helper ice_copy_phy_caps_to_cfg() to copy a
PHY capability to configuration instead duplicating the code for it.
Signed-off-by: Paul Greenwalt <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Using the new ice_aq_list_caps and ice_parse_(dev|func)_caps functions,
replace ice_discover_caps with two functions that each take a pointer to
the dev_caps and func_caps structures respectively.
This makes the side effect of updating the hw->dev_caps and
hw->func_caps obvious from reading the implementation of the function.
Additionally, it opens the way for enabling reading of device
capabilities outside of the initialization flow. By passing in
a pointer, another caller will be able to read the capabilities without
modifying the HW capabilities structures.
As there are no other callers, it is safe to now remove
ice_aq_discover_caps and ice_parse_caps.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The ice_parse_caps function is used to convert the capability block data
coming from firmware into a structured format used by other parts of the
code.
The current implementation directly updates the hw->func_caps and
hw->dev_caps structures. It is directly called from within
ice_aq_discover_caps. This causes the discover_caps function to have the
side effect of modifying the HW capability structures, which is not
intuitive.
Split this function into ice_parse_dev_caps and ice_parse_func_caps.
These functions will take a pointer to the dev_caps and func_caps
respectively. Also create an ice_parse_common_caps for sharing the
capability logic that is common to device and function.
Doing so enables a future refactor to allow reading and parsing
capabilities into a local caps structure instead of modifying the
members of the HW structure directly.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The ice_discover_caps function is used to read the device and function
capabilities, updating the hardware capabilities structures with
relevant data.
The exact number of capabilities returned by the hardware is unknown
ahead of time. The AdminQ command will report the total number of
capabilities in the return buffer.
The current implementation involves requesting capabilities once,
reading this returned size, and then re-requested with that size.
This isn't really necessary. The firmware interface has a maximum size
of ICE_AQ_MAX_BUF_LEN. Firmware can never return more than
ICE_AQ_MAX_BUF_LEN / sizeof(struct ice_aqc_list_caps_elem) capabilities.
Avoid the retry loop by simply allocating a buffer of size
ICE_AQ_MAX_BUF_LEN. This is significantly simpler than retrying. The
extra allocation isn't a big deal, as it will be released after we
finish parsing the capabilities.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Convert the pre-C90-extension "C struct hack" method (using a single-
element array at the end of a structure for implementing variable-length
types) to the preferred use of C99 flexible array member.
Additional code cleanups were done near areas affected by this change.
Signed-off-by: Bruce Allan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
There are a number of structures that consist of a one-element array as the
only struct member. Some of those are unused so remove them. Others are
used to index into a buffer/array consisting of a variable number of a
different data or structure type. Those are unnecessary since we can use
simple pointer arithmetic or index directly into the buffer to access
individual elements of the buffer/array.
Additional code cleanups were done near areas affected by this change.
Signed-off-by: Bruce Allan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Add a new devlink region used for capturing a snapshot of the device
capabilities buffer which is reported by the firmware over the AdminQ.
This information can useful in debugging driver and firmware
interactions.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
When setting the PHY cfg (CQ cmd 0x0601), if the firmware responds
with an EMODE error, software will ignore the error as it simply
means that manageability (ex: BMC) is in control of the link and that
the new setting may not be applied.
Signed-off-by: Chinh T Cao <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
|