aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/broadcom
AgeCommit message (Collapse)AuthorFilesLines
2020-10-26bnxt_en: Send HWRM_FUNC_RESET fw command unconditionally.Vasundhara Volam1-1/+2
In the AER or firmware reset flow, if we are in fatal error state or if pci_channel_offline() is true, we don't send any commands to the firmware because the commands will likely not reach the firmware and most commands don't matter much because the firmware is likely to be reset imminently. However, the HWRM_FUNC_RESET command is different and we should always attempt to send it. In the AER flow for example, the .slot_reset() call will trigger this fw command and we need to try to send it to effect the proper reset. Fixes: b340dc680ed4 ("bnxt_en: Avoid sending firmware messages when AER error is detected.") Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2020-10-26bnxt_en: Check abort error state in bnxt_open_nic().Michael Chan1-1/+4
bnxt_open_nic() is called during configuration changes that require the NIC to be closed and then opened. This call is protected by rtnl_lock. Firmware reset can be happening at the same time. Only critical portions of the entire firmware reset sequence are protected by the rtnl_lock. It is possible that bnxt_open_nic() can be called when the firmware reset sequence is aborting. In that case, bnxt_open_nic() needs to check if the ABORT_ERR flag is set and abort if it is. The configuration change that resulted in the bnxt_open_nic() call will fail but the NIC will be brought to a consistent IF_DOWN state. Without this patch, if bnxt_open_nic() were to continue in this error state, it may crash like this: [ 1648.659736] BUG: unable to handle kernel NULL pointer dereference at (null) [ 1648.659768] IP: [<ffffffffc01e9b3a>] bnxt_alloc_mem+0x50a/0x1140 [bnxt_en] [ 1648.659796] PGD 101e1b3067 PUD 101e1b2067 PMD 0 [ 1648.659813] Oops: 0000 [#1] SMP [ 1648.659825] Modules linked in: xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 tun bridge stp llc ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter sunrpc dell_smbios dell_wmi_descriptor dcdbas amd64_edac_mod edac_mce_amd kvm_amd kvm irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper vfat cryptd fat pcspkr ipmi_ssif sg k10temp i2c_piix4 wmi ipmi_si ipmi_devintf ipmi_msghandler tpm_crb acpi_power_meter sch_fq_codel ip_tables xfs libcrc32c sd_mod crc_t10dif crct10dif_generic mgag200 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm ahci drm libahci megaraid_sas crct10dif_pclmul crct10dif_common [ 1648.660063] tg3 libata crc32c_intel bnxt_en(OE) drm_panel_orientation_quirks devlink ptp pps_core dm_mirror dm_region_hash dm_log dm_mod fuse [ 1648.660105] CPU: 13 PID: 3867 Comm: ethtool Kdump: loaded Tainted: G OE ------------ 3.10.0-1152.el7.x86_64 #1 [ 1648.660911] Hardware name: Dell Inc. PowerEdge R7515/0R4CNN, BIOS 1.2.14 01/28/2020 [ 1648.661662] task: ffff94e64cbc9080 ti: ffff94f55df1c000 task.ti: ffff94f55df1c000 [ 1648.662409] RIP: 0010:[<ffffffffc01e9b3a>] [<ffffffffc01e9b3a>] bnxt_alloc_mem+0x50a/0x1140 [bnxt_en] [ 1648.663171] RSP: 0018:ffff94f55df1fba8 EFLAGS: 00010202 [ 1648.663927] RAX: 0000000000000000 RBX: ffff94e6827e0000 RCX: 0000000000000000 [ 1648.664684] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff94e6827e08c0 [ 1648.665433] RBP: ffff94f55df1fc20 R08: 00000000000001ff R09: 0000000000000008 [ 1648.666184] R10: 0000000000000d53 R11: ffff94f55df1f7ce R12: ffff94e6827e08c0 [ 1648.666940] R13: ffff94e6827e08c0 R14: ffff94e6827e08c0 R15: ffffffffb9115e40 [ 1648.667695] FS: 00007f8aadba5740(0000) GS:ffff94f57eb40000(0000) knlGS:0000000000000000 [ 1648.668447] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1648.669202] CR2: 0000000000000000 CR3: 0000001022772000 CR4: 0000000000340fe0 [ 1648.669966] Call Trace: [ 1648.670730] [<ffffffffc01f1d5d>] ? bnxt_need_reserve_rings+0x9d/0x170 [bnxt_en] [ 1648.671496] [<ffffffffc01fa7ea>] __bnxt_open_nic+0x8a/0x9a0 [bnxt_en] [ 1648.672263] [<ffffffffc01f7479>] ? bnxt_close_nic+0x59/0x1b0 [bnxt_en] [ 1648.673031] [<ffffffffc01fb11b>] bnxt_open_nic+0x1b/0x50 [bnxt_en] [ 1648.673793] [<ffffffffc020037c>] bnxt_set_ringparam+0x6c/0xa0 [bnxt_en] [ 1648.674550] [<ffffffffb8a5f564>] dev_ethtool+0x1334/0x21a0 [ 1648.675306] [<ffffffffb8a719ff>] dev_ioctl+0x1ef/0x5f0 [ 1648.676061] [<ffffffffb8a324bd>] sock_do_ioctl+0x4d/0x60 [ 1648.676810] [<ffffffffb8a326bb>] sock_ioctl+0x1eb/0x2d0 [ 1648.677548] [<ffffffffb8663230>] do_vfs_ioctl+0x3a0/0x5b0 [ 1648.678282] [<ffffffffb8b8e678>] ? __do_page_fault+0x238/0x500 [ 1648.679016] [<ffffffffb86634e1>] SyS_ioctl+0xa1/0xc0 [ 1648.679745] [<ffffffffb8b93f92>] system_call_fastpath+0x25/0x2a [ 1648.680461] Code: 9e 60 01 00 00 0f 1f 40 00 45 8b 8e 48 01 00 00 31 c9 45 85 c9 0f 8e 73 01 00 00 66 0f 1f 44 00 00 49 8b 86 a8 00 00 00 48 63 d1 <48> 8b 14 d0 48 85 d2 0f 84 46 01 00 00 41 8b 86 44 01 00 00 c7 [ 1648.681986] RIP [<ffffffffc01e9b3a>] bnxt_alloc_mem+0x50a/0x1140 [bnxt_en] [ 1648.682724] RSP <ffff94f55df1fba8> [ 1648.683451] CR2: 0000000000000000 Fixes: ec5d31e3c15d ("bnxt_en: Handle firmware reset status during IF_UP.") Reviewed-by: Vasundhara Volam <[email protected]> Reviewed-by: Pavan Chebbi <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2020-10-26bnxt_en: Re-write PCI BARs after PCI fatal error.Vasundhara Volam2-1/+19
When a PCIe fatal error occurs, the internal latched BAR addresses in the chip get reset even though the BAR register values in config space are retained. pci_restore_state() will not rewrite the BAR addresses if the BAR address values are valid, causing the chip's internal BAR addresses to stay invalid. So we need to zero the BAR registers during PCIe fatal error to force pci_restore_state() to restore the BAR addresses. These write cycles to the BAR registers will cause the proper BAR addresses to latch internally. Fixes: 6316ea6db93d ("bnxt_en: Enable AER support.") Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2020-10-26bnxt_en: Invoke cancel_delayed_work_sync() for PFs also.Vasundhara Volam1-11/+2
As part of the commit b148bb238c02 ("bnxt_en: Fix possible crash in bnxt_fw_reset_task()."), cancel_delayed_work_sync() is called only for VFs to fix a possible crash by cancelling any pending delayed work items. It was assumed by mistake that the flush_workqueue() call on the PF would flush delayed work items as well. As flush_workqueue() does not cancel the delayed workqueue, extend the fix for PFs. This fix will avoid the system crash, if there are any pending delayed work items in fw_reset_task() during driver's .remove() call. Unify the workqueue cleanup logic for both PF and VF by calling cancel_work_sync() and cancel_delayed_work_sync() directly in bnxt_remove_one(). Fixes: b148bb238c02 ("bnxt_en: Fix possible crash in bnxt_fw_reset_task().") Reviewed-by: Pavan Chebbi <[email protected]> Reviewed-by: Andy Gospodarek <[email protected]> Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2020-10-26bnxt_en: Fix regression in workqueue cleanup logic in bnxt_remove_one().Vasundhara Volam1-4/+5
A recent patch has moved the workqueue cleanup logic before calling unregister_netdev() in bnxt_remove_one(). This caused a regression because the workqueue can be restarted if the device is still open. Workqueue cleanup must be done after unregister_netdev(). The workqueue will not restart itself after the device is closed. Call bnxt_cancel_sp_work() after unregister_netdev() and call bnxt_dl_fw_reporters_destroy() after that. This fixes the regession and the original NULL ptr dereference issue. Fixes: b16939b59cc0 ("bnxt_en: Fix NULL ptr dereference crash in bnxt_fw_reset_task()") Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2020-10-12bnxt_en: Add stored FW version info to devlink info_get cb.Vasundhara Volam1-2/+45
This patch adds FW versions stored in the flash to devlink info_get callback. Return the correct fw.psid running version using the newly added bp->nvm_cfg_ver. v2: Ensure stored pkg_name string is NULL terminated when copied to devlink. Return directly from the last call to bnxt_dl_info_put(). If the FW call to get stored version fails for any reason, return success immediately to devlink without the stored versions. Reviewed-by: Andy Gospodarek <[email protected]> Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-10-12bnxt_en: Refactor bnxt_dl_info_get().Vasundhara Volam2-48/+71
Add a new function bnxt_dl_info_put() to simplify the code, as there are more stored firmware version fields to be added in the next patch. Also, rename fw_ver variable name to ncsi_ver for better naming while copying to devlink info_get cb. v2: Ensure active_pkg_name string is NULL terminated when copied to devlink. Return directly from the last call to bnxt_dl_info_put(). Reviewed-by: Pavan Chebbi <[email protected]> Reviewed-by: Andy Gospodarek <[email protected]> Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-10-12bnxt_en: Add bnxt_hwrm_nvm_get_dev_info() to query NVM info.Vasundhara Volam4-0/+31
Add a new bnxt_hwrm_nvm_get_dev_info() to query firmware version information via NVM_GET_DEV_INFO firmware command. Use it to get the running version of the NVM configuration information. This new function will also be used in subsequent patches to get the stored firmware versions. Reviewed-by: Andy Gospodarek <[email protected]> Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-10-12bnxt_en: Log unknown link speed appropriately.Michael Chan1-1/+5
If the VF virtual link is set to always enabled, the speed may be unknown when the physical link is down. The driver currently logs the link speed as 4294967295 Mbps which is SPEED_UNKNOWN. Modify the link up log message as "speed unknown" which makes more sense. Reviewed-by: Vasundhara Volam <[email protected]> Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-10-12bnxt_en: Log event_data1 and event_data2 when handling RESET_NOTIFY event.Michael Chan1-0/+3
Log these values that contain useful firmware state information. Reviewed-by: Edwin Peer <[email protected]> Reviewed-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-10-12bnxt_en: Simplify bnxt_async_event_process().Michael Chan1-9/+3
event_data1 and event_data2 are used when processing most events. Store these in local variables at the beginning of the function to simplify many of the case statements. Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-10-12bnxt_en: Set driver default message level.Michael Chan1-1/+3
Currently, bp->msg_enable has default value of 0. It is more useful to have the commonly used NETIF_MSG_DRV and NETIF_MSG_HW enabled by default. v2: Change the fall back bnxt_reset_task() inside bnxt_rx_ring_reset() to silent mode. With older fw, we would take the fall back path and it would be very noisy. Reviewed-by: Edwin Peer <[email protected]> Reviewed-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-10-12bnxt_en: Enable online self tests for multi-host/NPAR mode.Vasundhara Volam1-4/+4
Online self tests are not disruptive and can be run in NPAR mode and in multi-host NIC as well. Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-10-12bnxt_en: Return -EROFS to user space, if NVM writes are not permitted.Vasundhara Volam1-0/+2
If NVRAM resources are locked, NVM writes are not permitted. In such scenarios, firmware returns HWRM_ERR_CODE_RESOURCE_LOCKED error to firmware commands. Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2020-10-05Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller1-8/+8
Rejecting non-native endian BTF overlapped with the addition of support for it. The rest were more simple overlapping changes, except the renesas ravb binding update, which had to follow a file move as well as a YAML conversion. Signed-off-by: David S. Miller <[email protected]>
2020-10-04bnxt_en: Eliminate unnecessary RX resets.Michael Chan2-1/+53
Currently, the driver will schedule RX ring reset when we get a buffer error in the RX completion record. These RX buffer errors can be due to normal out-of-buffer conditions or a permanent error in the RX ring. Because the driver cannot distinguish between these 2 conditions, we assume all these buffer errors require reset. This is very disruptive when it is just a normal out-of-buffer condition. Newer firmware will now monitor the rings for the permanent failure and will send a notification to the driver when it happens. This allows the driver to reset only when such a notification is received. In environments where we have predominently out-of-buffer conditions, we now can avoid these unnecessary resets. Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-10-04bnxt_en: Reduce unnecessary message log during RX errors.Michael Chan1-2/+4
There is logic in the RX path to detect unexpected handles in the RX completion. We'll print a warning and schedule a reset. The next expected handle is then set to 0xffff which is guaranteed to not match any valid handle. This will force all remaining packets in the ring to be discarded before the reset. There can be hundreds of these packets remaining in the ring and there is no need to print the warnings for these forced errors. Reviewed-by: Pavan Chebbi <[email protected]> Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-10-04bnxt_en: Add a software counter for RX ring reset.Michael Chan3-4/+12
Add a per ring rx_resets counter to count these RX resets. Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-10-04bnxt_en: Implement RX ring reset in response to buffer errors.Michael Chan1-4/+75
On some older chips, it is necessary to do a reset when we get buffer errors associated with an RX ring. These buffer errors may become frequent if the RX ring underruns under heavy traffic. The current code does a global reset of all reasources when this happens. This works but creates a big disruption of all rings when one RX ring is having problem. This patch implements a localized RX ring reset of just the RX ring having the issue. All other rings including all TX rings will not be affected by this single RX ring reset. Only the older chips prior to the P5 class supports this reset. Because it is not a global reset, packets may still be arriving while we are calling firmware to reset that ring. We need to be sure that we don't post any buffers during this time while the ring is undergoing reset. After firmware completes successfully, the ring will be in the reset state with no buffers and we can start filling it with new buffers and posting them. Reviewed-by: Pavan Chebbi <[email protected]> Signed-off-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-10-04bnxt_en: Refactor bnxt_init_one_rx_ring().Michael Chan1-46/+50
bnxt_init_one_rx_ring() includes logic to initialize the BDs for one RX ring and to allocate the buffers. Separate the allocation logic into a new bnxt_alloc_one_rx_ring() function. The allocation function will be used later to allocate new buffers for one specified RX ring when we reset that RX ring. Reviewed-by: Pavan Chebbi <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-10-04bnxt_en: Refactor bnxt_free_rx_skbs().Michael Chan1-68/+66
bnxt_free_rx_skbs() frees all the allocated buffers and SKBs for every RX ring. Refactor this function by calling a new function bnxt_free_one_rx_ring_skbs() to free these buffers on one specified RX ring at a time. This is preparation work for resetting one RX ring during run-time. Reviewed-by: Pavan Chebbi <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-10-04bnxt_en: Log FW health status info, if reset is aborted.Michael Chan1-1/+8
If firmware does not come out of reset, log FW health status info to provide more information on firmware status. Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-10-04bnxt_en: perform no master recovery during startupEdwin Peer1-9/+29
The NS3 SoC platforms require assistance from the OP-TEE to recover firmware if a crash occurs while no driver is bound. The CRASHED_NO_MASTER condition is recorded in the firmware status register during the crash to indicate when driver intervension is needed to coordinate a firmware reload. This condition is detected during early driver initialization in order to effect a firmware fastboot on supported platforms when necessary. Reviewed-by: Vasundhara Volam <[email protected]> Signed-off-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-10-04bnxt_en: log firmware status on firmware init failureEdwin Peer2-5/+55
Firmware now supports device independent discovery of the status register location. This status register can provide more detailed information about firmware errors, especially if problems occur before the HWRM interface is functioning. Attempt to map this register if it is present and report the firmware status on firmware init failures. Signed-off-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-10-04bnxt_en: refactor bnxt_alloc_fw_health()Edwin Peer1-22/+38
The allocator for the firmware health structure conflates allocation and capability checks, limiting the reusability of the code. This patch separates out the capability check and disablement and improves the warning message to better describe the consequences of an allocation failure. Signed-off-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-10-04bnxt_en: Update firmware interface spec to 1.10.1.68.Vasundhara Volam1-3/+21
Main changes is to extend hwrm_nvm_get_dev_info_output() for stored firmware versions and a new flag is added to fw_status_reg. Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-10-03bnx2x: Use fallthrough pseudo-keywordGustavo A. R. Silva1-2/+2
Replace /* no break */ comments with the new pseudo-keyword macro fallthrough[1]. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27bnxt_en: Improve preset max value for ethtool -l.Michael Chan1-2/+7
The current logic that calculates the preset maximum value for combined channel does not take into account the rings used for XDP and mqprio TCs. Each of these features will reduce the number of TX rings. Add the logic to divide the TX rings accordingly based on whether the device is currently in XDP mode and whether TCs are in use. Reviewed-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27bnxt_en: Implement ethtool set_fec_param() method.Michael Chan3-1/+107
This feature allows the user to set the different FEC modes on the NIC port. Any new setting will take effect immediately after a link toggle. Reviewed-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27bnxt_en: Report Active FEC encoding during link up.Michael Chan1-3/+26
The current code is reporting the FEC configured settings during link up. Change it to report the more useful active FEC encoding that may be negotiated or auto detected. Reviewed-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27bnxt_en: Report FEC settings to ethtool.Michael Chan3-3/+109
Implement .get_fecparam() method to report the configured and active FEC settings. Also report the supported and advertised FEC settings to the .get_link_ksettings() method. Reviewed-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27bnxt_en: avoid link reset if speed is not changedEdwin Peer1-1/+9
PORT_PHY_CONFIG is always sent with REQ_FLAGS_RESET_PHY set. This flag must be set in order for the firmware to institute the requested PHY change immediately, but it results in a link flap. This is unnecessary and results in an improved user experience if the PHY reconfiguration is avoided when the user requested speed does not constitute a change. Signed-off-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27bnxt_en: Handle ethernet link being disabled by firmware.Michael Chan2-3/+29
On some 200G dual port NICs, if one port is configured to 200G, firmware will disable the ethernet link on the other port. Firmware will send notification to the driver for the disabled port when this happens. Define a new field in the link_info structure to keep track of this state. The new phy_state field replaces the unused loop_back field. Log a message when the phy_state changes state. In the disabled state, disallow any PHY configurations on the disabled port as the firmware will fail all calls to configure the PHY in this state. Reviewed-by: Vasundhara Volam <[email protected]> Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27bnxt_en: ethtool: support PAM4 link speeds up to 200GEdwin Peer1-8/+63
Add ethtool PAM4 link modes for: 50000baseCR_Full 100000baseCR2_Full 200000baseCR4_Full Signed-off-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27bnxt_en: add basic infrastructure to support PAM4 link speedsEdwin Peer2-21/+65
The firmware interface has added support for new link speeds using PAM4 modulation. Expand the bnxt_link_info structure to closely mirror the new firmware structures. Add logic to copy the PAM4 capabilities and settings from the firmware. Signed-off-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27bnxt_en: refactor bnxt_get_fw_speed()Edwin Peer1-23/+24
It will be necessary to update more than one field in the link_info structure when PAM4 speeds are added in a later patch. Instead of merely translating ethtool speed values to firmware speed values, change the responsiblity of this function to update all the necessary link_info fields required to force the speed change to the desired ethtool value. This also reduces code duplication somewhat at the two call sites, which otherwise both have to independently update link_info fields to turn off auto negotiation advertisements. Also use the appropriate REQ_FORCE_LINK_SPEED definitions. These happen to have the same values, but req_link_speed is utilimately passed as force_link_speed in HWRM_PORT_PHY_CFG which is not defined in terms of REQ_AUTO_LINK_SPEED. Reviewed-by: Scott Branden <[email protected]> Signed-off-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27bnxt_en: refactor code to limit speed advertisingEdwin Peer1-8/+12
Extract the code for determining an advertised speed is no longer supported into a separate function. This will avoid some code duplication in a later patch when supporting PAM4 speeds, since these speeds are specified in a separate field. Reviewed-by: Scott Branden <[email protected]> Signed-off-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-27bnxt_en: Update firmware interface spec to 1.10.1.65.Michael Chan5-113/+361
The main changes include FEC, ECN statistics, HWRM_PORT_PHY_QCFG response size reduction, and a new counter added to ctx_hw_stats_ext struct to support the new 58818 chip. The ctx_hw_stats_ext structure is now the superset supporting the new 58818 chips and the prior P5 chips. Add a new flag to identify the new chip and use constants for the chip specific ring statistics sizes instead of the size of the structure. Because the HWRM_PORT_PHY_QCFG response structure size has shrunk back to 96 bytes, the workaround added earlier to limit the size of this message for forwarding to the VF can be removed. Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25devlink: convert flash_update to use params structureJacob Keller1-3/+4
The devlink core recently gained support for checking whether the driver supports a flash_update parameter, via `supported_flash_update_params`. However, parameters are specified as function arguments. Adding a new parameter still requires modifying the signature of the .flash_update callback in all drivers. Convert the .flash_update function to take a new `struct devlink_flash_update_params` instead. By using this structure, and the `supported_flash_update_params` bit field, a new parameter to flash_update can be added without requiring modification to existing drivers. As before, all parameters except file_name will require driver opt-in. Because file_name is a necessary field to for the flash_update to make sense, no "SUPPORTED" bitflag is provided and it is always considered valid. All future additional parameters will require a new bit in the supported_flash_update_params bitfield. Signed-off-by: Jacob Keller <[email protected]> Reviewed-by: Jakub Kicinski <[email protected]> Cc: Jiri Pirko <[email protected]> Cc: Jakub Kicinski <[email protected]> Cc: Jonathan Corbet <[email protected]> Cc: Michael Chan <[email protected]> Cc: Bin Luo <[email protected]> Cc: Saeed Mahameed <[email protected]> Cc: Leon Romanovsky <[email protected]> Cc: Ido Schimmel <[email protected]> Cc: Danielle Ratson <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25devlink: check flash_update parameter support in net coreJacob Keller1-9/+3
When implementing .flash_update, drivers which do not support per-component update are manually checking the component parameter to verify that it is NULL. Without this check, the driver might accept an update request with a component specified even though it will not honor such a request. Instead of having each driver check this, move the logic into net/core/devlink.c, and use a new `supported_flash_update_params` field in the devlink_ops. Drivers which will support per-component update must now specify this by setting DEVLINK_SUPPORT_FLASH_UPDATE_COMPONENT in the supported_flash_update_params in their devlink_ops. This helps ensure that drivers do not forget to check for a NULL component if they do not support per-component update. This also enables a slightly better error message by enabling the core stack to set the netlink bad attribute message to indicate precisely the unsupported attribute in the message. Going forward, any new additional parameter to flash update will require a bit in the supported_flash_update_params bitfield. Signed-off-by: Jacob Keller <[email protected]> Reviewed-by: Jakub Kicinski <[email protected]> Cc: Jiri Pirko <[email protected]> Cc: Jonathan Corbet <[email protected]> Cc: Michael Chan <[email protected]> Cc: Bin Luo <[email protected]> Cc: Saeed Mahameed <[email protected]> Cc: Leon Romanovsky <[email protected]> Cc: Ido Schimmel <[email protected]> Cc: Danielle Ratson <[email protected]> Cc: Shannon Nelson <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-25drivers/net/ethernet: clean up mis-targeted commentsJesse Brandeburg4-57/+61
As part of the W=1 cleanups for ethernet, a million [*] driver comments had to be cleaned up to get the W=1 compilation to succeed. This change finally makes the drivers/net/ethernet tree compile with W=1 set on the command line. NOTE: The kernel uses kdoc style (see Documentation/process/kernel-doc.rst) when documenting code, not doxygen or other styles. After this patch the x86_64 build has no warnings from W=1, however scripts/kernel-doc says there are 1545 more warnings in source files, that I need to develop a script to fix in a followup patch. The errors fixed here are all kdoc of a few classes, with a few outliers: In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10: drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=] 1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff }; | ^~~~~~~~~~~~~~ ... repeats 4 times... drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body] 2084 | RX_USED_ADD(page, i); drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’: drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable] 603 | u32 tbisr, tanar, tanlpar; | ^~~~~ drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’: drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable] 1207 | u32 cfg, tanar, tbicr; | ^~~~~ drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable] 1063 | int data_size, yf_size; | ^~~~~~~ Normal kdoc fixes: warning: Function parameter or member 'x' not described in 'y' warning: Excess function parameter 'x' description in 'y' warning: Cannot understand <string> on line <NNN> - I thought it was a doc line [*] - ok it wasn't quite a million, but it felt like it. Signed-off-by: Jesse Brandeburg <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-24net/ethernet/broadcom: fix spelling typoWang Qing1-8/+8
Modify the comment typo: "compliment" -> "complement". Signed-off-by: Wang Qing <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller3-27/+54
Two minor conflicts: 1) net/ipv4/route.c, adding a new local variable while moving another local variable and removing it's initial assignment. 2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes. One pretty prints the port mode differently, whilst another changes the driver to try and obtain the port mode from the port node rather than the switch node. Signed-off-by: David S. Miller <[email protected]>
2020-09-20bnxt_en: Fix wrong flag value passed to HWRM_PORT_QSTATS_EXT fw call.Michael Chan1-1/+1
The wrong flag value caused the firmware call to return actual port counters instead of the counter masks. This messed up the counter overflow logic and caused erratic extended port counters to be displayed under ethtool -S. Fixes: 531d1d269c1d ("bnxt_en: Retrieve hardware masks for port counters.") Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-20bnxt_en: Fix HWRM_FUNC_QSTATS_EXT firmware call.Michael Chan1-0/+1
Fix it to set the required fid input parameter. The firmware call fails without this patch. Fixes: d752d0536c97 ("bnxt_en: Retrieve hardware counter masks from firmware if available.") Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-20bnxt_en: Return -EOPNOTSUPP for ETHTOOL_GREGS on VFs.Vasundhara Volam1-0/+3
Debug firmware commands are not supported on VFs to read registers. This patch avoids logging unnecessary access_denied error on VFs when user calls ETHTOOL_GREGS. By returning error in get_regs_len() method on the VF, the get_regs() method will not be called. Fixes: b5d600b027eb ("bnxt_en: Add support for 'ethtool -d'") Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-20bnxt_en: Protect bnxt_set_eee() and bnxt_set_pauseparam() with mutex.Michael Chan1-11/+20
All changes related to bp->link_info require the protection of the link_lock mutex. It's not sufficient to rely just on RTNL. Fixes: 163e9ef63641 ("bnxt_en: Fix race when modifying pause settings.") Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-20bnxt_en: return proper error codes in bnxt_show_tempEdwin Peer1-6/+13
Returning "unknown" as a temperature value violates the hwmon interface rules. Appropriate error codes should be returned via device_attribute show instead. These will ultimately be propagated to the user via the file system interface. In addition to the corrected error handling, it is an even better idea to not present the sensor in sysfs at all if it is known that the read will definitely fail. Given that temp1_input is currently the only sensor reported, ensure no hwmon registration if TEMP_MONITOR_QUERY is not supported or if it will fail due to access permissions. Something smarter may be needed if and when other sensors are added. Fixes: 12cce90b934b ("bnxt_en: fix HWRM error when querying VF temperature") Signed-off-by: Edwin Peer <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-20bnxt_en: Use memcpy to copy VPD field info.Vasundhara Volam1-3/+5
Using strlcpy() to copy from VPD is not correct because VPD strings are not necessarily NULL terminated. Use memcpy() to copy the VPD length up to the destination buffer size - 1. The destination is zeroed memory so it will always be NULL terminated. Fixes: a0d0fd70fed5 ("bnxt_en: Read partno and serialno of the board from VPD") Signed-off-by: Vasundhara Volam <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2020-09-19bnx2x: use true,false for bool variablesJason Yan1-3/+3
This addresses the following coccinelle warning: drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:15415:1-26: WARNING: Assignment of 0/1 to bool variable drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:12393:2-17: WARNING: Assignment of 0/1 to bool variable drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:15497:2-27: WARNING: Assignment of 0/1 to bool variable Reported-by: Hulk Robot <[email protected]> Signed-off-by: Jason Yan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.