| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In preparing to remove the .adjust_link api, I am moving the one-time
initialization of the device's Turbo Mode bit into a different execution
path. This code clears (disables) the Turbo Mode bit which is never used
by this driver. Turbo Mode is a non-standard mode that would allow the
100Mbps RMII interface to run at 200Mbps.
Signed-off-by: Jerry Ray <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Whitespace preparatory patch, making the dsa_switch_ops table consistent.
No code is added or removed.
Signed-off-by: Jerry Ray <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
We want to return negative error codes here but the copy_to/from_user()
functions return the number of bytes remaining to be copied.
Fixes: c59e12a140fb ("net: dsa: microchip: ptp: Initial hardware time stamping support")
Signed-off-by: Dan Carpenter <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/Y8fJxSvbl7UNVHh/@kili
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
ALU table entry 2 register in KSZ9477 have bit positions reserved for
forwarding port map. This field is referred in ksz9477_fdb_del() for
clearing forward port map and alu table.
But current fdb_del refer ALU table entry 3 register for accessing forward
port map. Update ksz9477_fdb_del() to get forward port map from correct
alu table entry register.
With this bug, issue can be observed while deleting static MAC entries.
Delete any specific MAC entry using "bridge fdb del" command. This should
clear all the specified MAC entries. But it is observed that entries with
self static alone are retained.
Tested on LAN9370 EVB since ksz9477_fdb_del() is used common across
LAN937x and KSZ series.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Rakesh Sankaranarayanan <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The T1 MDIO bus driver can perform both C22 and C45 transfers. Create
separate functions for each and register the C45 versions using the
new API calls where appropriate.
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The sja1105 MDIO bus driver only supports C45 transfers. Update the
function names to make this clear, pass the mmd as a parameter, and
register the accessors to the _c45 ops of the bus driver structure.
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
mt7530 does support C45, but its uses a mix of registering its MDIO
bus and providing its private MDIO bus to the DSA core, too. This makes
the change a bit more complex.
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The switch receives management traffic such as STP and LLDP. However, PTP
messages are not received, only transmitted.
Ideally, the switch would trap all PTP messages to the management CPU. This
particular switch has a PTP block which identifies PTP messages and traps them
to a dedicated port. There is a register to program this destination. This is
not used at the moment.
Therefore, program it to the same port as the MGMT traffic is trapped to. This
allows to receive PTP messages as soon as timestamping is enabled.
In addition, the datasheet mentions that this register is not valid e.g., for
6190 variants. So, add a new PTP operation which is added for the 6390 and 6290
devices.
Tested simply like this on Marvell 88E6390, revision 1:
|/ # ptp4l -2 -i lan4 --tx_timestamp_timeout=40 -m
|[...]
|ptp4l[147.450]: master offset 56 s2 freq +1262 path delay 413
|ptp4l[148.450]: master offset 22 s2 freq +1244 path delay 434
|ptp4l[149.450]: master offset 5 s2 freq +1234 path delay 446
|ptp4l[150.451]: master offset 3 s2 freq +1233 path delay 451
|ptp4l[151.451]: master offset 1 s2 freq +1232 path delay 451
|ptp4l[152.451]: master offset -3 s2 freq +1229 path delay 451
|ptp4l[153.451]: master offset 9 s2 freq +1240 path delay 451
Link: https://lore.kernel.org/r/CAFSKS=PJBpvtRJxrR4sG1hyxpnUnQpiHg4SrUNzAhkWnyt9ivg@mail.gmail.com
Signed-off-by: Kurt Kanzenbach <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Tested-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The enetc MDIO bus driver can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new API calls where appropriate.
This driver is shared with the Felix DSA switch, so update that at the
same time.
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
There is difference in implementation of per_out pins between KSZ9563
and LAN937x. In KSZ9563, Timestamping control register (0x052C) bit 6,
if 1 - timestamp input and 0 - trigger output. But it is opposite for
LAN937x 1 - trigger output and 0 - timestamp input.
As per per_out gpio pins, KSZ9563 has four Led pins and two dedicated
gpio pins. But in LAN937x dedicated gpio pins are removed instead there
are up to 10 LED pins out of which LED_0 and LED_1 can be mapped to PTP
tou 0, 1 or 2. This patch sets the bit 6 in 0x052C register and
configure the LED override and source register for LAN937x series of
switches alone.
Signed-off-by: Arun Ramadoss <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
LAN937x series of switches support 2 step timestamping mechanism. There
are timestamp correction calculation performed in ksz_rcv_timestamp and
ksz_xmit_timestamp which are applicable only for p2p1step. To check
whether the 2 step is enabled or not in tag_ksz.c introduced the helper
function in taggger_data to query it from ksz_ptp.c. Based on whether 2
step is enabled or not, timestamp calculation are performed.
Signed-off-by: Arun Ramadoss <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There are two programmable pins available for Trigger output unit to
generate periodic pulses. This patch add verify_pin for the available 2
pins and configure it with respect to GPIO index for the TOU unit.
Tested using testptp
./testptp -i 0 -L 0,2
./testptp -i 0 -d /dev/ptp0 -p 1000000000
./testptp -i 1 -L 1,2
./testptp -i 1 -d /dev/ptp0 -p 100000000
Signed-off-by: Arun Ramadoss <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
LAN937x and KSZ PTP supported switches has Three Trigger output unit.
This TOU can used to generate the periodic signal for PTP. TOU has the
cycle width register of 32 bit in size and period width register of 24
bit, each value is of 8ns so the pulse width can be maximum 125ms.
Tested using ./testptp -d /dev/ptp0 -p 1000000000 -w 100000000 for
generating the 10ms pulse width
Signed-off-by: Christian Eggers <[email protected]>
Co-developed-by: Arun Ramadoss <[email protected]>
Signed-off-by: Arun Ramadoss <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
For PDelay_Resp messages we will likely have a negative value in the
correction field. The switch hardware cannot correctly update such
values (produces an off by one error in the UDP checksum), so it must be
moved to the time stamp field in the tail tag. Format of the correction
field is 48 bit ns + 16 bit fractional ns. After updating the
correction field, clone is no longer required hence it is freed.
Signed-off-by: Christian Eggers <[email protected]>
Co-developed-by: Arun Ramadoss <[email protected]>
Signed-off-by: Arun Ramadoss <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds the routines for transmission of ptp packets. When the
ptp pdelay_req packet to be transmitted, it uses the deferred xmit
worker to schedule the packets.
During irq_setup, interrupt for Sync, Pdelay_req and Pdelay_rsp are
enabled. So interrupt is triggered for all three packets. But for
p2p1step, we require only time stamp of Pdelay_req packet. Hence to
avoid posting of the completion from ISR routine for Sync and
Pdelay_resp packets, ts_en flag is introduced. This controls which
packets need to processed for timestamp.
After the packet is transmitted, ISR is triggered. The time at which
packet transmitted is recorded to separate register.
This value is reconstructed to absolute time and posted to the user
application through socket error queue.
Signed-off-by: Christian Eggers <[email protected]>
Co-developed-by: Arun Ramadoss <[email protected]>
Signed-off-by: Arun Ramadoss <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Rx Timestamping is done through 4 additional bytes in tail tag.
Whenever the ptp packet is received, the 4 byte hardware time stamped
value is added before 1 byte tail tag. Also, bit 7 in tail tag indicates
it as PTP frame. This 4 byte value is extracted from the tail tag and
reconstructed to absolute time and assigned to skb hwtstamp.
If the packet received in PDelay_Resp, then partial ingress timestamp
is subtracted from the correction field. Since user space tools expects
to be done in hardware.
Signed-off-by: Christian Eggers <[email protected]>
Co-developed-by: Arun Ramadoss <[email protected]>
Signed-off-by: Arun Ramadoss <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
PTP Interrupt mask and status register differ from the global and port
interrupt mechanism by two methods. One is that for global/port
interrupt enabling we have to clear the bit but for ptp interrupt we
have to set the bit. And other is bit12:0 is reserved in ptp interrupt
registers. This forced to not use the generic implementation of
global/port interrupt method routine. This patch implement the ptp
interrupt mechanism to read the timestamp register for sync, pdelay_req
and pdelay_resp.
Signed-off-by: Arun Ramadoss <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch is used for reconstructing the absolute time from the 32bit
hardware time stamping value. The do_aux ioctl is used for reading the
ptp hardware clock and store it to global variable.
The timestamped value in tail tag during rx and register during tx are
32 bit value (2 bit seconds and 30 bit nanoseconds). The time taken to
read entire ptp clock will be time consuming. In order to speed up, the
software clock is maintained. This clock time will be added to 32 bit
timestamp to get the absolute time stamp.
Signed-off-by: Christian Eggers <[email protected]>
Co-developed-by: Arun Ramadoss <[email protected]>
Signed-off-by: Arun Ramadoss <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When the PTP is enabled in hardware bit 6 of PTP_MSG_CONF1 register, the
transmit frame needs additional 4 bytes before the tail tag. It is
needed for all the transmission packets irrespective of PTP packets or
not.
The 4-byte timestamp field is 0 for frames other than Pdelay_Resp. For
the one-step Pdelay_Resp, the switch needs the receive timestamp of the
Pdelay_Req message so that it can put the turnaround time in the
correction field.
Since PTP has to be enabled for both Transmission and reception
timestamping, driver needs to track of the tx and rx setting of the all
the user ports in the switch.
Two flags hw_tx_en and hw_rx_en are added in ksz_port to track the
timestampping setting of each port. When any one of ports has tx or rx
timestampping enabled, bit 6 of PTP_MSG_CONF1 is set and it is indicated
to tag_ksz.c through tagger bytes. This flag adds 4 additional bytes to
the tail tag. When tx and rx timestamping of all the ports are disabled,
then 4 bytes are not added.
Tested using hwstamp -i <interface>
Signed-off-by: Arun Ramadoss <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]> # mostly api
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds the routine for get_ts_info, hwstamp_get, set. This enables
the PTP support towards userspace applications such as linuxptp.
Signed-off-by: Christian Eggers <[email protected]>
Co-developed-by: Arun Ramadoss <[email protected]>
Signed-off-by: Arun Ramadoss <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch implement routines (adjfine, adjtime, gettime and settime)
for manipulating the chip's PTP clock. It registers the ptp caps
to posix clock register.
Signed-off-by: Christian Eggers <[email protected]>
Co-developed-by: Arun Ramadoss <[email protected]>
Signed-off-by: Arun Ramadoss <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]> # mostly api
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Jacob Keller <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The global2 SMI MDIO bus driver can perform both C22 and C45
transfers. Create separate functions for each and register the C45
versions using the new API calls where appropriate. Update the SERDES
code to make use of these new accessors.
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: Michael Walle <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This implementation for the Marvell mv88e6xxx chip series is based on
handling ATU miss violations occurring when packets ingress on a port
that is locked with learning on. This will trigger a
SWITCHDEV_FDB_ADD_TO_BRIDGE event, which will result in the bridge module
adding a locked FDB entry. This bridge FDB entry will not age out as
it has the extern_learn flag set.
Userspace daemons can listen to these events and either accept or deny
access for the host, by either replacing the locked FDB entry with a
simple entry or leave the locked entry.
If the host MAC address is already present on another port, a ATU
member violation will occur, but to no real effect, and the packet will
be dropped in hardware. Statistics on these violations can be shown with
the command and example output of interest:
ethtool -S ethX
NIC statistics:
...
atu_member_violation: 5
atu_miss_violation: 23
...
Where ethX is the interface of the MAB enabled port.
Furthermore, as added vlan interfaces where the vid is not added to the
VTU will cause ATU miss violations reporting the FID as
MV88E6XXX_FID_STANDALONE, we need to check and skip the miss violations
handling in this case.
Signed-off-by: Hans J. Schultz <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
mv88e6xxx_g1_atu_prob_irq_thread_fn()
As only the hardware access functions up til and including
mv88e6xxx_g1_atu_mac_read() called under the interrupt handler
need to take the chip lock, we release the chip lock after this call.
The follow up code that handles the violations can run without the
chip lock held.
In further patches, the violation handler function will even be
incompatible with having the chip lock held. This due to an AB/BA
ordering inversion with rtnl_lock().
Signed-off-by: Hans J. Schultz <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
The default return value -EOPNOTSUPP of mv88e6xxx_port_bridge_flags()
came from the return value of the DSA method port_egress_floods() in
commit 4f85901f0063 ("net: dsa: mv88e6xxx: add support for bridge flags"),
but the DSA API was changed in commit a8b659e7ff75 ("net: dsa: act as
passthrough for bridge port flags"), resulting in the return value
-EOPNOTSUPP not being valid anymore, and sections for new flags will not
need to set the return value to zero on success, as with the new mab flag
added in a following patch.
Signed-off-by: Hans J. Schultz <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Improve mdio master read/write by using singe mii read/write lo/hi.
In a read and write we need to poll the mdio master regs in a busy loop
to check for a specific bit present in the upper half of the reg. We can
ignore the other half since it won't contain useful data. This will save
an additional useless read for each read and write operation.
In a read operation the returned data is present in the mdio master reg
lower half. We can ignore the other half since it won't contain useful
data. This will save an additional useless read for each read operation.
In a read operation it's needed to just set the hi half of the mdio
master reg as the lo half will be replaced by the result. This will save
an additional useless write for each read operation.
Tested-by: Ronald Wahl <[email protected]>
Signed-off-by: Christian Marangi <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
It may be useful to read/write just the lo or hi half of a reg.
This is especially useful for phy poll with the use of mdio master.
The mdio master reg is composed by the first 16 bit related to setup and
the other half with the returned data or data to write.
Refactor the mii function to permit single mii read/write of lo or hi
half of the reg.
Tested-by: Ronald Wahl <[email protected]>
Signed-off-by: Christian Marangi <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This reverts commit 2481d206fae7884cd07014fd1318e63af35e99eb.
The Documentation is very confusing about the topic.
The cache logic for hi and lo is wrong and actually miss some regs to be
actually written.
What the Documentation actually intended was that it's possible to skip
writing hi OR lo if half of the reg is not needed to be written or read.
Revert the change in favor of a better and correct implementation.
Reported-by: Ronald Wahl <[email protected]>
Signed-off-by: Christian Marangi <[email protected]>
Cc: [email protected] # v5.18+
Signed-off-by: David S. Miller <[email protected]>
|
|
The assumption that Documentation was right about how this value work was
wrong. It was discovered that the length value of the mgmt header is in
step of word size.
As an example to process 4 byte of data the correct length to set is 2.
To process 8 byte 4, 12 byte 6, 16 byte 8...
Odd values will always return the next size on the ack packet.
(length of 3 (6 byte) will always return 8 bytes of data)
This means that a value of 15 (0xf) actually means reading/writing 32 bytes
of data instead of 16 bytes. This behaviour is totally absent and not
documented in the switch Documentation.
In fact from Documentation the max value that mgmt eth can process is
16 byte of data while in reality it can process 32 bytes at once.
To handle this we always round up the length after deviding it for word
size. We check if the result is odd and we round another time to align
to what the switch will provide in the ack packet.
The workaround for the length limit of 15 is still needed as the length
reg max value is 0xf(15)
Reported-by: Ronald Wahl <[email protected]>
Tested-by: Ronald Wahl <[email protected]>
Fixes: 90386223f44e ("net: dsa: qca8k: add support for larger read/write size with mgmt Ethernet")
Signed-off-by: Christian Marangi <[email protected]>
Cc: [email protected] # v5.18+
Signed-off-by: David S. Miller <[email protected]>
|
|
PTP hardware timestamping related objects are not linked when PTP
support for MV88E6xxx (NET_DSA_MV88E6XXX_PTP) is disabled, therefore
NET_DSA_MV88E6XXX should not depend on PTP_1588_CLOCK_OPTIONAL
regardless of NET_DSA_MV88E6XXX_PTP.
Instead, condition more strictly on how NET_DSA_MV88E6XXX_PTP's
dependencies are met, making sure that it cannot be enabled when
NET_DSA_MV88E6XXX=y and PTP_1588_CLOCK=m.
In other words, this commit allows NET_DSA_MV88E6XXX to be built-in
while PTP_1588_CLOCK is a module, as long as NET_DSA_MV88E6XXX_PTP is
prevented from being enabled.
Fixes: e5f31552674e ("ethernet: fix PTP_1588_CLOCK dependencies")
Signed-off-by: Johnny S. Lee <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
KSZ swithes used interrupts for detecting the phy link up and down.
During registering the interrupt handler, it used IRQF_TRIGGER_FALLING
flag. But this flag has to be retrieved from device tree instead of hard
coding in the driver, so removing the flag.
Fixes: ff319a644829 ("net: dsa: microchip: move interrupt handling logic from lan937x to ksz_common")
Reported-by: Christian Eggers <[email protected]>
Signed-off-by: Arun Ramadoss <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Russell King correctly pointed out that the MAC_2500FD capability is
already added for port 5 (if not in RGMII mode) and port 6 (which only
supports SGMII) by mt7531_mac_port_get_caps. Remove the reduntant
setting of this capability flag which was added by a previous commit.
Fixes: e19de30d2080 ("net: dsa: mt7530: add support for in-band link status")
Reported-by: Russell King (Oracle) <[email protected]>
Reviewed-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
In the blamed commit, it was not noticed that one implementation of
chip->info->ops->phylink_get_caps(), called by mv88e6xxx_get_caps(),
may access hardware registers, and in doing so, it takes the
mv88e6xxx_reg_lock(). Namely, this is mv88e6352_phylink_get_caps().
This is a problem because mv88e6xxx_get_caps(), apart from being
a top-level function (method invoked by dsa_switch_ops), is now also
directly called from mv88e6xxx_setup_port(), which runs under the
mv88e6xxx_reg_lock() taken by mv88e6xxx_setup(). Therefore, when running
on mv88e6352, the reg_lock would be acquired a second time and the
system would deadlock on driver probe.
The things that mv88e6xxx_setup() can compete with in terms of register
access with are the IRQ handlers and MDIO bus operations registered by
mv88e6xxx_probe(). So there is a real need to acquire the register lock.
The register lock can, in principle, be dropped and re-acquired pretty
much at will within the driver, as long as no operations that involve
waiting for indirect access to complete (essentially, callers of
mv88e6xxx_smi_direct_wait() and mv88e6xxx_wait_mask()) are interrupted
with the lock released. However, I would guess that in mv88e6xxx_setup(),
the critical section is kept open for such a long time just in order to
optimize away multiple lock/unlock operations on the registers.
We could, in principle, drop the reg_lock right before the
mv88e6xxx_setup_port() -> mv88e6xxx_get_caps() call, and
re-acquire it immediately afterwards. But this would look ugly, because
mv88e6xxx_setup_port() would release a lock which it didn't acquire, but
the caller did.
A cleaner solution to this issue comes from the observation that struct
mv88e6xxxx_ops methods generally assume they are called with the
reg_lock already acquired. Whereas mv88e6352_phylink_get_caps() is more
the exception rather than the norm, in that it acquires the lock itself.
Let's enforce the same locking pattern/convention for
chip->info->ops->phylink_get_caps() as well, and make
mv88e6xxx_get_caps(), the top-level function, acquire the register lock
explicitly, for this one implementation that will access registers for
port 4 to work properly.
This means that mv88e6xxx_setup_port() will no longer call the top-level
function, but the low-level mv88e6xxx_ops method which expects the
correct calling context (register lock held).
Compared to chip->info->ops->phylink_get_caps(), mv88e6xxx_get_caps()
also fixes up the supported_interfaces bitmap for internal ports, since
that can be done generically and does not require per-switch knowledge.
That's code which will no longer execute, however mv88e6xxx_setup_port()
doesn't need that. It just needs to look at the mac_capabilities bitmap.
Fixes: cc1049ccee20 ("net: dsa: mv88e6xxx: fix speed setting for CPU/DSA ports")
Reported-by: Maksim Kiselev <[email protected]>
Signed-off-by: Vladimir Oltean <[email protected]>
Tested-by: Maksim Kiselev <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Merge in the left-over fixes before the net-next pull-request.
net/mptcp/subflow.c
d3295fee3c75 ("mptcp: use proper req destructor for IPv6")
36b122baf6a8 ("mptcp: add subflow_v(4,6)_send_synack()")
Signed-off-by: Paolo Abeni <[email protected]>
|
|
It is possible to trigger these VTU violation messages very easily,
it's only necessary to send packets with an unknown VLAN ID to a port
that belongs to a VLAN-aware bridge.
Do a similar thing as for ATU violation messages, and hide them in the
kernel's trace buffer.
New usage model:
$ trace-cmd list | grep mv88e6xxx
mv88e6xxx
mv88e6xxx:mv88e6xxx_vtu_miss_violation
mv88e6xxx:mv88e6xxx_vtu_member_violation
$ trace-cmd report
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Saeed Mahameed <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
In applications where the switch ports must perform 802.1X based
authentication and are therefore locked, ATU violation interrupts are
quite to be expected as part of normal operation. The problem is that
they currently spam the kernel log, even if rate limited.
Create a series of trace points, all derived from the same event class,
which log these violations to the kernel's trace buffer, which is both
much faster and much easier to ignore than printing to a serial console.
New usage model:
$ trace-cmd list | grep mv88e6xxx
mv88e6xxx
mv88e6xxx:mv88e6xxx_atu_full_violation
mv88e6xxx:mv88e6xxx_atu_miss_violation
mv88e6xxx:mv88e6xxx_atu_member_violation
$ trace-cmd record -e mv88e6xxx sleep 10
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Saeed Mahameed <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
When an ATU violation occurs, the switch uses the ATU FID register to
report the FID of the MAC address that incurred the violation. It would
be good for the driver to know the FID value for purposes such as
logging and CPU-based authentication.
Up until now, the driver has been calling the mv88e6xxx_g1_atu_op()
function to read ATU violations, but that doesn't do exactly what we
want, namely it calls mv88e6xxx_g1_atu_fid_write() with FID 0.
(side note, the documentation for the ATU Get/Clear Violation command
says that writes to the ATU FID register have no effect before the
operation starts, it's only that we disregard the value that this
register provides once the operation completes)
So mv88e6xxx_g1_atu_fid_write() is not what we want, but rather
mv88e6xxx_g1_atu_fid_read(). However, the latter doesn't exist, we need
to write it.
The remainder of mv88e6xxx_g1_atu_op() except for
mv88e6xxx_g1_atu_fid_write() is still needed, namely to send a
GET_CLR_VIOLATION command to the ATU. In principle we could have still
kept calling mv88e6xxx_g1_atu_op(), but the MDIO writes to the ATU FID
register are pointless, but in the interest of doing less CPU work per
interrupt, write a new function called mv88e6xxx_g1_read_atu_violation()
and call it.
The FID will be the port default FID as set by mv88e6xxx_port_set_fid()
if the VID from the packet cannot be found in the VTU. Otherwise it is
the FID derived from the VTU entry associated with that VID.
Signed-off-by: Hans J. Schultz <[email protected]>
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Currently, the MV88E6XXX_PORT_ASSOC_VECTOR_INT_AGE_OUT bit (interrupt on
age out) is not enabled by the driver, and as a result, the print for
age out violations is dead code.
Remove it until there is some way for this to be triggered.
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This patch fixes an issue where a read failure of a port statistic counter
will return unknown results. While it is highly unlikely the read will
ever fail, it is much cleaner to return a zero for the stat count.
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Jerry Ray <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The SJA1105 family has 45 L2 policing table entries
(SJA1105_MAX_L2_POLICING_COUNT) and SJA1110 has 110
(SJA1110_MAX_L2_POLICING_COUNT). Keeping the table structure but
accounting for the difference in port count (5 in SJA1105 vs 10 in
SJA1110) does not fully explain the difference. Rather, the SJA1110 also
has L2 ingress policers for multicast traffic. If a packet is classified
as multicast, it will be processed by the policer index 99 + SRCPORT.
The sja1105_init_l2_policing() function initializes all L2 policers such
that they don't interfere with normal packet reception by default. To have
a common code between SJA1105 and SJA1110, the index of the multicast
policer for the port is calculated because it's an index that is out of
bounds for SJA1105 but in bounds for SJA1110, and a bounds check is
performed.
The code fails to do the proper thing when determining what to do with the
multicast policer of port 0 on SJA1105 (ds->num_ports = 5). The "mcast"
index will be equal to 45, which is also equal to
table->ops->max_entry_count (SJA1105_MAX_L2_POLICING_COUNT). So it passes
through the check. But at the same time, SJA1105 doesn't have multicast
policers. So the code programs the SHARINDX field of an out-of-bounds
element in the L2 Policing table of the static config.
The comparison between index 45 and 45 entries should have determined the
code to not access this policer index on SJA1105, since its memory wasn't
even allocated.
With enough bad luck, the out-of-bounds write could even overwrite other
valid kernel data, but in this case, the issue was detected using KASAN.
Kernel log:
sja1105 spi5.0: Probed switch chip: SJA1105Q
==================================================================
BUG: KASAN: slab-out-of-bounds in sja1105_setup+0x1cbc/0x2340
Write of size 8 at addr ffffff880bd57708 by task kworker/u8:0/8
...
Workqueue: events_unbound deferred_probe_work_func
Call trace:
...
sja1105_setup+0x1cbc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Allocated by task 8:
...
sja1105_setup+0x1bcc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Fixes: 38fbe91f2287 ("net: dsa: sja1105: configure the multicast policers, if present")
CC: [email protected] # 5.15+
Signed-off-by: Radu Nicolae Pirea (OSS) <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Add stats64 support for ksz8xxx series of switches.
Signed-off-by: Oleksij Rempel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The ethernet-controller dt-schema, mostly pushed forward by Linux, has
the "internal" PHY mode for denoting MAC connections to an internal PHY.
U-Boot may provide device tree blobs where this phy-mode is specified,
so make the Linux driver accept them.
It appears that the current behavior with phy-mode = "internal" was
introduced when mv88e6xxx started reporting supported_interfaces to
phylink. Prior to that, I don't think it would have any issues accepting
this phy-mode.
Fixes: d4ebf12bcec4 ("net: dsa: mv88e6xxx: populate supported_interfaces and mac_capabilities")
Link: https://lore.kernel.org/linux-arm-kernel/20221205172709.kglithpbhdbsakvd@skbuf/T/
Reported-by: Tim Harvey <[email protected]>
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Tested-by: Tim Harvey <[email protected]> # imx6q-gw904.dts
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
To make the code more comparable to KSZ9477 code, move DSA
configurations to the same location.
Signed-off-by: Oleksij Rempel <[email protected]>
Acked-by: Arun Ramadoss <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
compatible switches
KSZ8795 and KSZ9477 compatible series of switches use global max frame
size configuration register. So, enable MTU normalization for this reason.
Signed-off-by: Oleksij Rempel <[email protected]>
Acked-by: Arun Ramadoss <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Make MTU configurable on KSZ87xx and KSZ88xx series of switches.
Before this patch, pre-configured behavior was different on different
switch series, due to opposite meaning of the same bit:
- KSZ87xx: Reg 4, Bit 1 - if 1, max frame size is 1532; if 0 - 1514
- KSZ88xx: Reg 4, Bit 1 - if 1, max frame size is 1514; if 0 - 1532
Since the code was telling "... SW_LEGAL_PACKET_DISABLE, true)", I
assume, the idea was to set max frame size to 1532.
With this patch, by setting MTU size 1500, both switch series will be
configured to the 1532 frame limit.
This patch was tested on KSZ8873.
Signed-off-by: Oleksij Rempel <[email protected]>
Acked-by: Arun Ramadoss <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Add ksz_rmw8(), it will be used in the next patch.
Signed-off-by: Oleksij Rempel <[email protected]>
Acked-by: Arun Ramadoss <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
If we have global MTU configuration, it is enough to configure it on CPU
port only.
Signed-off-by: Oleksij Rempel <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Paolo Abeni <[email protected]>
|
|
There are no HW specific registers, so we can process all of them
in one location.
Signed-off-by: Oleksij Rempel <[email protected]>
Tested-by: Arun Ramadoss <[email protected]> (KSZ9893 and LAN937x)
Signed-off-by: Paolo Abeni <[email protected]>
|
|
When dsa_devlink_region_create failed in sja1105_setup_devlink_regions(),
priv->regions is not released.
Fixes: bf425b82059e ("net: dsa: sja1105: expose static config as devlink region")
Signed-off-by: Zhengchao Shao <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|