| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
While no supported devices currently utilize EXT0, the register reserves
the bits for an EXT0. EXT0 is utilized by devices from the generation
prior to rtl8365mb, such as those supported by the driver library
rtl8367b.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240212-realtek-fix_ext0-v1-1-f3d2536d191a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Embed dsa_switch within realtek_priv to eliminate the need for a second
memory allocation.
Suggested-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The realtek-mdio will now use this driver instead of the generic DSA
driver ("dsa user smi"), which should not be used with OF[1].
With a single ds_ops for both interfaces, the ds_ops in realtek_priv is
no longer necessary. Now, the realtek_variant.ds_ops can be used
directly.
The realtek_priv.setup_interface() has been removed as we can directly
call the new common function.
[1] https://lkml.kernel.org/netdev/20220630200423.tieprdu5fpabflj7@bang-olufsen.dk/T/
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the user MDIO driver, despite numerous references to SMI, including
its compatible string, there's nothing inherently specific about the SMI
interface in the user MDIO bus. Consequently, the code has been migrated
to the rtl83xx module. All references to SMI have been eliminated.
The MDIO bus id was changed from Realtek-<switch id> to the switch
devname suffixed with :user_mii, giving more information about the bus
it is referencing.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the line assigning dev.of_node in mdio_bus as subsequent
of_mdiobus_register will always overwrite it.
As discussed in [1], allow the DSA core to be simplified, by not
assigning ds->user_mii_bus when the MDIO bus is described in OF, as it
is unnecessary.
Since commit 3b73a7b8ec38 ("net: mdio_bus: add refcounting for fwnodes
to mdiobus"), we can put the "mdio" node just after the MDIO bus
registration.
[1] https://lkml.kernel.org/netdev/20231213120656.x46fyad6ls7sqyzv@skbuf/T/#u
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The binding docs requires for SMI-connected devices that the switch
must have a child node named "mdio" and with a compatible string of
"realtek,smi-mdio". Meanwile, for MDIO-connected switches, the binding
docs only requires a child node named "mdio".
This patch changes the driver to use the common denominator for both
interfaces, looking for the MDIO node by name, ignoring the compatible
string.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since rtl83xx and realtek-{smi,mdio} are always loaded together,
we can optimize resource usage by consolidating them into a single
module.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some code can be shared between both interface modules (MDIO and SMI)
and among variants. These interface functions migrated to a common
module:
- rtl83xx_lock
- rtl83xx_unlock
- rtl83xx_probe
- rtl83xx_register_switch
- rtl83xx_unregister_switch
- rtl83xx_shutdown
- rtl83xx_remove
The reset during probe was moved to the end of the common probe. This way,
we avoid a reset if anything else fails.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of copying values from the variant, we can keep a reference in
realtek_priv.
This is a preliminary change for sharing code betwen interfaces. It will
allow to move most of the probe into a common module while still allow
code specific to each interface to read variant fields.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, the interface modules realtek-smi and realtek-mdio served as
a platform and an MDIO driver, respectively. Each interface module
redundantly specified the same compatible strings for both variants and
referenced symbols from the variants.
Now, each variant module has been transformed into a unified driver
serving both as a platform and an MDIO driver. This modification
reverses the relationship between the interface and variant modules,
with the variant module now utilizing symbols from the interface
modules.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a namespace to group the exported symbols.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was never used and never referenced.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit f86ad77faf24 ("net: dsa: bcm_sf2: Utilize b53_{enable,
disable}_port"), bcm_sf2.c no longer calls b53_eee_enable_set(), and all
its callers are in b53_common.c.
We also need to move it, because it is called within b53_common.c before
its definition, and we want to avoid forward declarations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240206112527.4132299-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There's no need to clear the config->supported_interfaces bitmap before
reporting the supported interfaces as all bits in the bitmap will already
be initialized to zero when the phylink_config structure is allocated. The
"config" pointer points to &dp->phylink_config, and "dp" is allocated by
dsa_port_touch() with kzalloc(), so all its fields are filled with zeroes.
There's no code that would change the bitmap beforehand. Remove it.
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-7-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On the switch on the MT7988 SoC, as shown in Block Diagram 8.1.1.3 on page
125 of "MT7988A Wi-Fi 7 Generation Router Platform: Datasheet (Open
Version) v0.1", there are only 4 PHYs. That's port 0 to 3. Set the case for
ports which connect to switch PHYs to '0 ... 3'.
Port 4 and 5 are not used at all in this design.
Link: https://wiki.banana-pi.org/Banana_Pi_BPI-R4#Documents [1]
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-6-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The pad_setup function pointer was introduced with 88bdef8be9f6 ("net: dsa:
mt7530: Extend device data ready for adding a new hardware"). It was being
used to set up the core clock and port 6 of the MT7530 switch, and pll of
the MT7531 switch.
All of these were moved to more appropriate locations, and it was never
used for the switch on the MT7988 SoC. Therefore, this function pointer
hasn't got a use anymore. Remove it.
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-5-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mt7530_pad_clk_setup() is called if port 6 is enabled. It used to do more
things than setting up port 6. That part was moved to more appropriate
locations, mt7530_setup() and mt7530_pll_setup().
Now that all it does is set up port 6, rename it to mt7530_setup_port6(),
and move it to a more appropriate location, under mt7530_mac_config().
Change mt7530_setup_port6() to void as there're no error cases.
Leave an empty mt7530_pad_clk_setup() to satisfy the pad_setup function
pointer.
This is the code path for setting up the ports before:
dsa_switch_ops :: phylink_mac_config() -> mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt753x_info :: mac_port_config() -> mt7530_mac_config()
-> mt7530_setup_port5()
-> mt753x_pad_setup()
-> mt753x_info :: pad_setup() -> mt7530_pad_clk_setup()
This is after:
dsa_switch_ops :: phylink_mac_config() -> mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt753x_info :: mac_port_config() -> mt7530_mac_config()
-> mt7530_setup_port5()
-> mt7530_setup_port6()
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-4-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This code is from before this driver was converted to phylink API. Phylink
deals with the unsupported interface cases before mt7530_pad_clk_setup() is
run. Therefore, the default case would never run. However, it must be
defined nonetheless to handle all the remaining enumeration values, the
phy-modes.
Switch to if statement for RGMII and return which simplifies the code and
saves an indent.
Set P6_INTF_MODE, which is the three least significant bits of the
MT7530_P6ECR register, to 0 for RGMII even though it will already be 0
after reset. This is to keep supporting dynamic reconfiguration of the port
in the case the interface changes from TRGMII to RGMII.
Disable the TRGMII clocks for all cases. They will be enabled if TRGMII is
being used.
Read XTAL after checking for RGMII as it's only needed for the TRGMII
interface mode.
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-3-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The crystal frequency concerns the switch core. The frequency should be
checked when the switch is being set up so the driver can reject the
unsupported hardware earlier and without requiring port 6 to be used.
Move it to mt7530_setup(). Drop the unnecessary function printing.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-2-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There're two code paths for setting up port 5:
mt7530_setup()
-> mt7530_setup_port5()
mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt7530_mac_config()
-> mt7530_setup_port5()
On the first code path, priv->p5_intf_sel is either set to
P5_INTF_SEL_PHY_P0 or P5_INTF_SEL_PHY_P4 when mt7530_setup_port5() is run.
On the second code path, priv->p5_intf_sel is set to P5_INTF_SEL_GMAC5 when
mt7530_setup_port5() is run.
Empty the default case which will never run but is needed nonetheless to
handle all the remaining enumeration values.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-1-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
b53_get_mac_eee() sets both eee_enabled and eee_active, and then
returns zero.
dsa_slave_get_eee(), which calls this function, will then continue to
call phylink_ethtool_get_eee(), which will return -EOPNOTSUPP if there
is no PHY present, otherwise calling phy_ethtool_get_eee() which in
turn will call genphy_c45_ethtool_get_eee().
genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active
with its own interpretation from the PHYs settings and negotiation
result.
Thus, when there is no PHY, dsa_slave_get_eee() will fail with
-EOPNOTSUPP, meaning eee_enabled and eee_active will not be returned to
userspace. When there is a PHY, eee_enabled and eee_active will be
overwritten by phylib, making the setting of these members in
b53_get_mac_eee() entirely unnecessary.
Remove this code, thus simplifying b53_get_mac_eee().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/E1rWbNI-002cCz-4x@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MDIO bus drivers can return -ENODEV when they know the bus does not
have a device at the given address, e.g. because of hardware
limitation. One such limitation is that the bus does not support C45
at all. This is more efficient than returning 0xffff, since it
immediately stops the probing on the given address, where as further
reads can be made when 0xffff is returned.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was pointed out during the review [1] of commit 68e1010cda79 ("net:
dsa: qca8k: put MDIO bus OF node on qca8k_mdio_register() failure") that
the rest of the qca8k driver uses "int ret" rather than "int err".
Make everything consistent in that regard, not only
qca8k_mdio_register(), but also qca8k_setup_mdio_bus().
[1] https://lore.kernel.org/netdev/qyl2w3ownx5q7363kqxib52j5htar4y6pkn7gen27rj45xr4on@pvy5agi6o2te/
Suggested-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was pointed out during the review [1] of commit e66bf63a7f67 ("net:
dsa: qca8k: skip MDIO bus creation if its OF node has status =
"disabled"") that we now leak a reference to the "mdio" OF node if it is
disabled.
This is only a concern when using dynamic OF as far as I can tell (like
probing on an overlay), since OF nodes are never freed in the regular
case. Additionally, I'm unaware of any actual device trees (in
production or elsewhere) which have status = "disabled" for the MDIO OF
node. So handling this as a simple enhancement.
[1] https://lore.kernel.org/netdev/CAJq09z4--Ug+3FAmp=EimQ8HTQYOWOuVon-PUMGB5a1N=RPv4g@mail.gmail.com/
Suggested-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This commit introduces support for the KSZ8567, a robust 7-port
Ethernet switch. The KSZ8567 features two RGMII/MII/RMII interfaces,
each capable of gigabit speeds, complemented by five 10/100 Mbps
MAC/PHYs.
Signed-off-by: Philippe Schenker <philippe.schenker@impulsing.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240130083419.135763-2-dev@pschenker.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Not all mv88e6xxx device support C45 read/write operations. Those
which do not return -EOPNOTSUPP. However, when phylib scans the bus,
it considers this fatal, and the probe of the MDIO bus fails, which in
term causes the mv88e6xxx probe as a whole to fail.
When there is no device on the bus for a given address, the pull up
resistor on the data line results in the read returning 0xffff. The
phylib core code understands this when scanning for devices on the
bus. C45 allows multiple devices to be supported at one address, so
phylib will perform a few reads at each address, so although thought
not the most efficient solution, it is a way to avoid fatal
errors. Make use of this as a minimal fix for stable to fix the
probing problems.
Follow up patches will rework how C45 operates to make it similar to
C22 which considers -ENODEV as a none-fatal, and swap mv88e6xxx to
using this.
Cc: stable@vger.kernel.org
Fixes: 743a19e38d02 ("net: dsa: mv88e6xxx: Separate C22 and C45 transactions")
Reported-by: Tim Menninger <tmenninger@purestorage.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240129224948.1531452-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
side
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When working with GPIO, its direction must be set either when the GPIO is
requested by gpiod_get*() or later on by one of the gpiod_direction_*()
functions. Neither of this is done here which results in undefined
behavior on some systems.
As the reset GPIO is used right after it is requested here, it makes sense
to configure it as GPIOD_OUT_HIGH right away. With that, the following
gpiod_set_value_cansleep(1) becomes redundant and can be safely
removed.
Fixes: a653f2f538f9 ("net: dsa: qca8k: introduce reset via gpio feature")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1706266175-3408-1-git-send-email-michal.vokac@ysoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There's no need to run all the code on mt7530_setup_port5() if port 5 is
disabled. The only case for calling mt7530_setup_port5() from
mt7530_setup() is when PHY muxing is enabled. That is because port 5 is not
defined as a port on the devicetree, therefore, it cannot be controlled by
phylink.
Because of this, run mt7530_setup_port5() if priv->p5_intf_sel is
P5_INTF_SEL_PHY_P0 or P5_INTF_SEL_PHY_P4. Remove the P5_DISABLED case from
mt7530_setup_port5().
Stop initialising the interface variable as the remaining cases will always
call mt7530_setup_port5() with it initialised.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-7-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Running mt7530_setup_port5() from mt7530_setup() used to handle all cases
of configuring port 5, including phylink.
Setting priv->p5_interface under mt7530_setup_port5() makes sure that
mt7530_setup_port5() from mt753x_phylink_mac_config() won't run.
The commit ("net: dsa: mt7530: improve code path for setting up port 5")
makes so that mt7530_setup_port5() from mt7530_setup() runs only on
non-phylink cases.
Get rid of unnecessarily setting priv->p5_interface under
mt7530_setup_port5() as port 5 phylink configuration will be done by
running mt7530_setup_port5() from mt753x_phylink_mac_config() now.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-6-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There're two code paths for setting up port 5:
mt7530_setup()
-> mt7530_setup_port5()
mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt7530_mac_config()
-> mt7530_setup_port5()
Currently mt7530_setup_port5() from mt7530_setup() always runs. If port 5
is used as a CPU, DSA, or user port, mt7530_setup_port5() from
mt753x_phylink_mac_config() won't run. That is because priv->p5_interface
set on mt7530_setup_port5() will match state->interface on
mt753x_phylink_mac_config() which will stop running mt7530_setup_port5()
again.
Therefore, mt7530_setup_port5() will never run from
mt753x_phylink_mac_config().
Address this by not running mt7530_setup_port5() from mt7530_setup() if
port 5 is used as a CPU, DSA, or user port. This driver isn't in the
dsa_switches_apply_workarounds[] array so phylink will always be present.
To keep the cases where port 5 isn't controlled by phylink working as
before, preserve the mt7530_setup_port5() call from mt7530_setup().
Do not set priv->p5_intf_sel to P5_DISABLED. It is already set to that when
"priv" is allocated.
Move setting the interface to a more specific location. It's supposed to be
overwritten if PHY muxing is detected.
Improve the comment which explains the process.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-5-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There's no logic to numerically order the CPU ports. Just state the port
number instead.
Remove the irrelevant PHY muxing information from
mt7530_mac_port_get_caps(). Explain the supported MII modes instead.
Remove the out of place PHY muxing information from
mt753x_phylink_mac_config(). The function is for MT7530, MT7531, and the
switch on the MT7988 SoC but there's no PHY muxing on MT7531 or the switch
on the MT7988 SoC.
These comments were gradually introduced with the commits below.
commit ca366d6c889b ("net: dsa: mt7530: Convert to PHYLINK API")
commit 38f790a80560 ("net: dsa: mt7530: Add support for port 5")
commit 88bdef8be9f6 ("net: dsa: mt7530: Extend device data ready for adding
a new hardware")
commit c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-4-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce the p5_sgmii field to store the information for whether port 5
has got SGMII or not. Instead of reading the MT7531_TOP_SIG_SR register
multiple times, the register will be read once and the value will be
stored on the p5_sgmii field. This saves unnecessary reads of the
register.
Move the comment about MT7531AE and MT7531BE to mt7531_setup(), where the
switch is identified.
Get rid of mt7531_dual_sgmii_supported() now that priv->p5_sgmii stores the
information. Address the code where mt7531_dual_sgmii_supported() is used.
Get rid of mt7531_is_rgmii_port() which just prints the opposite of
priv->p5_sgmii.
Instead of calling mt7531_pll_setup() then returning, do not call it if
port 5 is SGMII.
Remove P5_INTF_SEL_GMAC5_SGMII. The p5_interface_select enum is supposed to
represent the mode that port 5 is being used in, not the hardware
information of port 5. Set p5_intf_sel to P5_INTF_SEL_GMAC5 instead, if
port 5 is not dsa_is_unused_port().
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-3-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the p5_interface_select enumeration as the data type for the
p5_intf_sel field. This ensures p5_intf_sel can only take the values
defined in the p5_interface_select enumeration.
Remove the explicit assignment of 0 to P5_DISABLED as the first enum item
is automatically assigned 0.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-2-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On the MT7530 switch, the CPU_PORT field indicates which CPU port to trap
frames to, regardless of the affinity of the inbound user port.
When multiple CPU ports are in use, if the DSA conduit interface is down,
trapped frames won't be passed to the conduit interface.
To make trapping frames work including this case, implement
ds->ops->conduit_state_change() on this subdriver and set the CPU_PORT
field to the numerically smallest CPU port whose conduit interface is up.
Introduce the active_cpu_ports field to store the information of the active
CPU ports. Correct the macros, CPU_PORT is bits 4 through 6 of the
register.
Add a comment to explain frame trapping for this switch.
Currently, the driver doesn't support the use of multiple CPU ports so this
is not necessarily a bug fix.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-1-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KSZ8873
Correct the PHY loopback bit handling in the ksz8_w_phy_bmcr and
ksz8_r_phy_bmcr functions for KSZ8794 and KSZ8873 variants in the ksz8795
driver. Previously, the code erroneously used Bit 7 of port register 0xD
for both chip variants, which is actually for LED configuration. This
update ensures the correct registers and bits are used for the PHY
loopback feature:
- For KSZ8794: Use 0xF / Bit 7.
- For KSZ8873: Use 0xD / Bit 0.
The lack of loopback support was seen on KSZ8873 system by using
"ethtool -t lanX". After this patch, the ethtool selftest will work,
but only if port is not part of a bridge.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the manual checks for register value changes in the
ksz8_w_phy_bmcr function. Instead, rely on regmap_update_bits() for
optimizing register updates.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Isolate the Basic Mode Control Register (BMCR) operations in the ksz8795
driver by moving the BMCR-related code segments from the ksz8_r_phy()
and ksz8_w_phy() functions to newly created ksz8_r_phy_bmcr() and
ksz8_w_phy_bmcr() functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Quoting from commit 4223f8651287 ("net: dsa: mt7530: make NET_DSA_MT7530
select MEDIATEK_GE_PHY"):
Make MediaTek MT753x DSA driver enable MediaTek Gigabit PHYs driver to
properly control MT7530 and MT7531 switch PHYs.
A noticeable change is that the behaviour of switchport interfaces going
up-down-up-down is no longer there.
Now, the switch can be used without the PHYs but, at the moment, every
hardware design out there that I have seen uses them. For that, it would
make the most sense to force the selection of MEDIATEK_GE_PHY for the MDIO
interface which currently controls the MT7530 and MT7531 switches.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122053451.8004-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Setup PMCR port register for actual speed and duplex on internally
connected PHYs of the MT7988 built-in switch. This fixes links with
speeds other than 1000M.
Fixes: 110c18bfed41 ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/a5b04dfa8256d8302f402545a51ac4c626fdba25.1706071272.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the MDIO bus of the switches the MT7530 DSA subdriver controls
can only be registered as non-OF-based. Bring support for registering the
bus OF-based.
The subdrivers that control switches [with MDIO bus] probed on OF must
follow this logic to support all cases properly:
No switch MDIO bus defined: Populate ds->user_mii_bus, register the MDIO
bus, set the interrupts for PHYs if "interrupt-controller" is defined at
the switch node. This case should only be covered for the switches which
their dt-bindings documentation didn't document the MDIO bus from the
start. This is to keep supporting the device trees that do not describe the
MDIO bus on the device tree but the MDIO bus is being used nonetheless.
Switch MDIO bus defined: Don't populate ds->user_mii_bus, register the MDIO
bus, set the interrupts for PHYs if ["interrupt-controller" is defined at
the switch node and "interrupts" is defined at the PHY nodes under the
switch MDIO bus node].
Switch MDIO bus defined but explicitly disabled: If the device tree says
status = "disabled" for the MDIO bus, we shouldn't need an MDIO bus at all.
Instead, just exit as early as possible and do not call any MDIO API.
The use of ds->user_mii_bus is inappropriate when the MDIO bus of the
switch is described on the device tree [1], which is why we don't populate
ds->user_mii_bus in that case.
Link: https://lore.kernel.org/netdev/20231213120656.x46fyad6ls7sqyzv@skbuf/ [1]
Suggested-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122053431.7751-1-arinc.unal@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure.
Fixes: 05bd97fc559d ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240111072018.75971-1-chentao@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There used to be a of_node_put(priv->master_mii_dn) call in
bcm_sf2_mdio_unregister(), which was accidentally deleted in commit
6ca80638b90c ("net: dsa: Use conduit and user terms").
But it's not needed - we don't need to hold a reference on the
"brcm,unimac-mdio" OF node for that long, since we don't do anything
with it. We can release it as soon as we finish bcm_sf2_mdio_register().
Also reduce "if (err && dn)" to just "if (err)". We know "dn", aka the
former priv->master_mii_dn, is non-NULL. Otherwise, of_mdio_find_bus(dn)
would not have been able to find the bus behind "brcm,unimac-mdio".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bcm_sf2 driver does something strange. Instead of calling
of_mdiobus_register() with an OF node argument, it manually assigns the
bus->dev->of_node and then calls the non-OF mdiobus_register(). This
circumvents some code from __of_mdiobus_register() from running, which
sets the auto-scan mask, parses some device tree properties, etc.
I'm going to go out on a limb and say that the OF node isn't, in fact,
needed at all, and can be removed. The MDIO diversion as initially
implemented in commit 461cd1b03e32 ("net: dsa: bcm_sf2: Register our
slave MDIO bus") looked quite different than it is now, after commit
771089c2a485 ("net: dsa: bcm_sf2: Ensure that MDIO diversion is used").
Initially, it made sense, as bcm_sf2 was registering another set of
driver ops for the "brcm,unimac-mdio" OF node. But now, it deletes all
phandles, which makes "phy-handle"s unable to find PHYs, which means
that it always goes through the OF-unaware dsa_user_phy_connect().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Accessed either through priv->dev or ds->dev, it is the same device
structure. Keep a single variable which holds a reference to it, and use
it consistently.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__of_mdiobus_register() already calls __mdiobus_register() if the
OF node provided as argument is NULL. We can take advantage of that
and simplify the 2 code path, calling devm_of_mdiobus_register() only
once for both cases.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To simplify reasoning about why the DSA framework provides the
ds->user_mii_bus functionality, drivers should only use it if they
need to. The qca8k driver appears to also use it simply as storage
for a pointer, which is not a good enough reason to make the core
much more difficult to follow.
ds->user_mii_bus is useful for only 2 cases:
1. The driver probes on platform_data (no OF)
2. The driver probes on OF, but there is no OF node for the MDIO bus.
It is unclear if case (1) is supported with qca8k. It might not be:
the driver might crash when of_device_get_match_data() returns NULL
and then it dereferences priv->info without NULL checking.
Anyway, let us limit the ds->user_mii_bus usage only to the above cases,
and not assign it when an OF node is present.
The bus->phy_mask assignment follows along with the movement, because
__of_mdiobus_register() overwrites this bus field anyway. The value set
by the driver only matters for the non-OF code path.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the driver calls the non-OF devm_mdiobus_register() rather
than devm_of_mdiobus_register() for this case, but it seems to rather
be a confusing coincidence, and not a real use case that needs to be
supported.
If the device tree says status = "disabled" for the MDIO bus, we
shouldn't need an MDIO bus at all. Instead, just exit as early as
possible and do not call any MDIO API.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_get_child_by_name() gives us an OF node with an elevated refcount,
which should be dropped when we're done with it. This is so that,
if (of_node_check_flag(node, OF_DYNAMIC)) is true, the node's memory can
eventually be freed.
There are 2 distinct paths to be considered in qca8k_mdio_register():
- devm_of_mdiobus_register() succeeds: since commit 3b73a7b8ec38 ("net:
mdio_bus: add refcounting for fwnodes to mdiobus"), the MDIO core
treats this well.
- devm_of_mdiobus_register() or anything up to that point fails: it is
the duty of the qca8k driver to release the OF node.
This change addresses the second case by making sure that the OF node
reference is not leaked.
The "mdio" node may be NULL, but of_node_put(NULL) is safe.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|