| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The variable is just assigned the value of a macro, so it can be
removed.
Signed-off-by: Alvin Šipraga <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The maximum number of ports is actually 11, according to two
observations:
1. The highest port ID used in the vendor driver is 10. Since port IDs
are indexed from 0, and since DSA follows the same numbering system,
this means up to 11 ports are to be presumed.
2. The registers with port mask fields always amount to a maximum port
mask of 0x7FF, corresponding to a maximum 11 ports.
In view of this, I also deleted the comment.
Signed-off-by: Alvin Šipraga <[email protected]>
Reviewed-by: Luiz Angelo Daros de Luca <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
There is no real need for this variable: the line change interrupt mask
is sufficiently masked out when getting linkup_ind and linkdown_ind in
the interrupt handler.
Signed-off-by: Alvin Šipraga <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The official name of this switch is RTL8367RB-VB, not RTL8367RB. There
is also an RTL8367RB-VC which is rather different. Change the name of
the CHIP_ID/_VER macros for reasons of consistency.
Signed-off-by: Alvin Šipraga <[email protected]>
Reviewed-by: Luiz Angelo Daros de Luca <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Replace last occurences of hardcoded cpu-port by cpu_dp member of
dsa_port struct.
Now the constant can be dropped.
Suggested-by: Vladimir Oltean <[email protected]>
Signed-off-by: Frank Wunderlich <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Enumerate available cpu-ports instead of using hardcoded constant.
Suggested-by: Vladimir Oltean <[email protected]>
Signed-off-by: Frank Wunderlich <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Rework vlan_add/vlan_del functions in preparation for dynamic cpu port.
Currently BIT(MT7530_CPU_PORT) is added to new_members, even though
mt7530_port_vlan_add() will be called on the CPU port too.
Let DSA core decide when to call port_vlan_add for the CPU port, rather
than doing it implicitly.
We can do autonomous forwarding in a certain VLAN, but not add br0 to that
VLAN and avoid flooding the CPU with those packets, if software knows it
doesn't need to process them.
Suggested-by: Vladimir Oltean <[email protected]>
Signed-off-by: Frank Wunderlich <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf and netfilter.
Current release - regressions:
- eth: amt: fix possible null-ptr-deref in amt_rcv()
Previous releases - regressions:
- tcp: use alloc_large_system_hash() to allocate table_perturb
- af_unix: fix a data-race in unix_dgram_peer_wake_me()
- nfc: st21nfca: fix memory leaks in EVT_TRANSACTION handling
- eth: ixgbe: fix unexpected VLAN rx in promisc mode on VF
Previous releases - always broken:
- ipv6: fix signed integer overflow in __ip6_append_data
- netfilter:
- nat: really support inet nat without l3 address
- nf_tables: memleak flow rule from commit path
- bpf: fix calling global functions from BPF_PROG_TYPE_EXT programs
- openvswitch: fix misuse of the cached connection on tuple changes
- nfc: nfcmrvl: fix memory leak in nfcmrvl_play_deferred
- eth: altera: fix refcount leak in altera_tse_mdio_create
Misc:
- add Quentin Monnet to bpftool maintainers"
* tag 'net-5.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (45 commits)
net: amd-xgbe: fix clang -Wformat warning
tcp: use alloc_large_system_hash() to allocate table_perturb
net: dsa: realtek: rtl8365mb: fix GMII caps for ports with internal PHY
net: dsa: mv88e6xxx: correctly report serdes link failure
net: dsa: mv88e6xxx: fix BMSR error to be consistent with others
net: dsa: mv88e6xxx: use BMSR_ANEGCOMPLETE bit for filling an_complete
net: altera: Fix refcount leak in altera_tse_mdio_create
net: openvswitch: fix misuse of the cached connection on tuple changes
net: ethernet: mtk_eth_soc: fix misuse of mem alloc interface netdev[napi]_alloc_frag
ip_gre: test csum_start instead of transport header
au1000_eth: stop using virt_to_bus()
ipv6: Fix signed integer overflow in l2tp_ip6_sendmsg
ipv6: Fix signed integer overflow in __ip6_append_data
nfc: nfcmrvl: Fix memory leak in nfcmrvl_play_deferred
nfc: st21nfca: fix incorrect sizing calculations in EVT_TRANSACTION
nfc: st21nfca: fix memory leaks in EVT_TRANSACTION handling
nfc: st21nfca: fix incorrect validating logic in EVT_TRANSACTION
net: ipv6: unexport __init-annotated seg6_hmac_init()
net: xfrm: unexport __init-annotated xfrm4_protocol_init()
net: mdio: unexport __init-annotated mdio_bus_init()
...
|
|
Since commit a18e6521a7d9 ("net: phylink: handle NA interface mode in
phylink_fwnode_phy_connect()"), phylib defaults to GMII when no phy-mode
or phy-connection-type property is specified in a DSA port node of the
device tree. The same commit caused a regression in rtl8365mb whereby
phylink would fail to connect, because the driver did not advertise
support for GMII for ports with internal PHY.
It should be noted that the aforementioned regression is not because the
blamed commit was incorrect: on the contrary, the blamed commit is
correcting the previous behaviour whereby unspecified phy-mode would
cause the internal interface mode to be PHY_INTERFACE_MODE_NA. The
rtl8365mb driver only worked by accident before because it _did_
advertise support for PHY_INTERFACE_MODE_NA, despite NA being reserved
for internal use by phylink. With one mistake fixed, the other was
exposed.
Commit a5dba0f207e5 ("net: dsa: rtl8365mb: add GMII as user port mode")
then introduced implicit support for GMII mode on ports with internal
PHY to allow a PHY connection for device trees where the phy-mode is not
explicitly set to "internal". At this point everything was working OK
again.
Subsequently, commit 6ff6064605e9 ("net: dsa: realtek: convert to
phylink_generic_validate()") broke this behaviour again by discarding
the usage of rtl8365mb_phy_mode_supported() - where this GMII support
was indicated - while switching to the new .phylink_get_caps API.
With the new API, rtl8365mb_phy_mode_supported() is no longer needed.
Remove it altogether and add back the GMII capability - this time to
rtl8365mb_phylink_get_caps() - so that the above default behaviour works
for ports with internal PHY again.
Fixes: 6ff6064605e9 ("net: dsa: realtek: convert to phylink_generic_validate()")
Signed-off-by: Alvin Šipraga <[email protected]>
Reviewed-by: Russell King (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Phylink wants to know if the link has dropped since the last time state
was retrieved, and the BMSR gives us that. Read the BMSR and use it when
deciding the link state. Fill in the an_complete member as well for the
emulated PHY state.
Signed-off-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Other errors accessing the registers in mv88e6352_serdes_pcs_get_state()
print "PHY " before the register name, except for the BMSR. Make this
consistent with the other error messages.
Signed-off-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Commit ede359d8843a ("net: dsa: mv88e6xxx: Link in pcs_get_state() if AN
is bypassed") added the ability to link if AN was bypassed, and added
filling of state->an_complete field, but set it to true if AN was
enabled in BMCR, not when AN was reported complete in BMSR.
This was done because for some reason, when I wanted to use BMSR value
to infer an_complete, I was looking at BMSR_ANEGCAPABLE bit (which was
always 1), instead of BMSR_ANEGCOMPLETE bit.
Use BMSR_ANEGCOMPLETE for filling state->an_complete.
Fixes: ede359d8843a ("net: dsa: mv88e6xxx: Link in pcs_get_state() if AN is bypassed")
Signed-off-by: Marek Behún <[email protected]>
Signed-off-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node.
when breaking early from a for_each_available_child_of_node() loop,
we need to explicitly call of_node_put() on the gphy_fw_np.
Add missing of_node_put() to avoid refcount leak.
Fixes: 14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Miaoqian Lin <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
When kernel.h is used in the headers it adds a lot into dependency hell,
especially when there are circular dependencies are involved.
Replace kernel.h inclusion with the list of what is really being used.
Signed-off-by: Christophe JAILLET <[email protected]>
Link: https://lore.kernel.org/r/41d99ef8629e1db03d4f2662f5556611e0b94652.1654323308.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Pull bitmap updates from Yury Norov:
- bitmap: optimize bitmap_weight() usage, from me
- lib/bitmap.c make bitmap_print_bitmask_to_buf parseable, from Mauro
Carvalho Chehab
- include/linux/find: Fix documentation, from Anna-Maria Behnsen
- bitmap: fix conversion from/to fix-sized arrays, from me
- bitmap: Fix return values to be unsigned, from Kees Cook
It has been in linux-next for at least a week with no problems.
* tag 'bitmap-for-5.19-rc1' of https://github.com/norov/linux: (31 commits)
nodemask: Fix return values to be unsigned
bitmap: Fix return values to be unsigned
KVM: x86: hyper-v: replace bitmap_weight() with hweight64()
KVM: x86: hyper-v: fix type of valid_bank_mask
ia64: cleanup remove_siblinginfo()
drm/amd/pm: use bitmap_{from,to}_arr32 where appropriate
KVM: s390: replace bitmap_copy with bitmap_{from,to}_arr64 where appropriate
lib/bitmap: add test for bitmap_{from,to}_arr64
lib: add bitmap_{from,to}_arr64
lib/bitmap: extend comment for bitmap_(from,to)_arr32()
include/linux/find: Fix documentation
lib/bitmap.c make bitmap_print_bitmask_to_buf parseable
MAINTAINERS: add cpumask and nodemask files to BITMAP_API
arch/x86: replace nodes_weight with nodes_empty where appropriate
mm/vmstat: replace cpumask_weight with cpumask_empty where appropriate
clocksource: replace cpumask_weight with cpumask_empty in clocksource.c
genirq/affinity: replace cpumask_weight with cpumask_empty where appropriate
irq: mips: replace cpumask_weight with cpumask_empty where appropriate
drm/i915/pmu: replace cpumask_weight with cpumask_empty where appropriate
arch/x86: replace cpumask_weight with cpumask_empty where appropriate
...
|
|
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
mv88e6xxx_mdio_register() pass the device node to of_mdiobus_register().
We don't need the device node after it.
Add missing of_node_put() to avoid refcount leak.
Fixes: a3c53be55c95 ("net: dsa: mv88e6xxx: Support multiple MDIO busses")
Signed-off-by: Miaoqian Lin <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
drivers/net/ethernet/cadence/macb_main.c
5cebb40bc955 ("net: macb: Fix PTP one step sync support")
138badbc21a0 ("net: macb: use NAPI for TX completion path")
https://lore.kernel.org/all/[email protected]/
net/smc/af_smc.c
75c1edf23b95 ("net/smc: postpone sk_refcnt increment in connect()")
3aba103006bc ("net/smc: align the connect behaviour with TCP")
https://lore.kernel.org/all/[email protected]/
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Update the VCAP filters to support multiple tag_8021q CPU ports.
TX works using a filter for VLAN ID on the ingress of the CPU port, with
a redirect and a VLAN pop action. This can be updated trivially by
amending the ingress port mask of this rule to match on all tag_8021q
CPU ports.
RX works using a filter for ingress port on the egress of the CPU port,
with a VLAN push action. Here we need to replicate these filters for
each tag_8021q CPU port, and let them all have the same action.
This means that the OCELOT_VCAP_ES0_TAG_8021Q_RXVLAN() cookie needs to
encode a unique value for every {user port, CPU port} pair it's given.
Do this by encoding the CPU port in the upper 16 bits of the cookie, and
the user port in the lower 16 bits.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There is a desire for the felix driver to gain support for multiple
tag_8021q CPU ports, but the current model prevents it.
This is because ocelot_apply_bridge_fwd_mask() only takes into
consideration whether a port is a tag_8021q CPU port, but not whose CPU
port it is.
We need a model where we can have a direct affinity between an ocelot
port and a tag_8021q CPU port. This serves as the basis for multiple CPU
ports.
Declare a "dsa_8021q_cpu" backpointer in struct ocelot_port which
encodes that affinity. Repurpose the "ocelot_set_dsa_8021q_cpu" API to
"ocelot_assign_dsa_8021q_cpu" to express the change of paradigm.
Note that this change makes the first practical use of the new
ocelot_port->index field in ocelot_port_unassign_dsa_8021q_cpu(), where
we need to remove the old tag_8021q CPU port from the reserved VLAN range.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Absorb the final details of calling ocelot_port_{,un}set_dsa_8021q_cpu(),
i.e. the need to lock &ocelot->fwd_domain_lock, into the callee, to
simplify the caller and permit easier code reuse later.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
tag_8021q CPU
Add more logic to ocelot_port_{,un}set_dsa_8021q_cpu() from the ocelot
switch lib by encapsulating the ocelot_apply_bridge_fwd_mask() call that
felix used to have.
This is necessary because the CPU port change procedure will also need
to do this, and it's good to reduce code duplication by having an entry
point in the ocelot switch lib that does all that is needed.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
PGID_CPU must be updated every time a port is configured or unconfigured
as a tag_8021q CPU port. The ocelot switch lib already has a hook for
that operation, so move the updating of PGID_CPU to those hooks.
These bits are pretty specific to DSA, so normally I would keep them out
of the common switch lib, but when tag_8021q is in use, this has
implications upon the forwarding mask determined by
ocelot_apply_bridge_fwd_mask() and called extensively by the switch lib.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
PGID_BC is configured statically by ocelot_init() to flood towards the
CPU port module, and dynamically by ocelot_port_set_bcast_flood()
towards all user ports.
When the tagging protocol changes, the intention is to turn off flooding
towards the old pipe towards the host, and to turn it on towards the new
pipe.
Due to a recent change which removed the adjustment of PGID_BC from
felix_set_host_flood(), 3 things happen.
- when we change from NPI to tag_8021q mode: in this mode, the CPU port
module is accessed via registers, and used to read PTP packets with
timestamps. We fail to disable broadcast flooding towards the CPU port
module, and to enable broadcast flooding towards the physical port
that serves as a DSA tag_8021q CPU port.
- from tag_8021q to NPI mode: in this mode, the CPU port module is
redirected to a physical port. We fail to disable broadcast flooding
towards the physical tag_8021q CPU port, and to enable it towards the
CPU port module at ocelot->num_phys_ports.
- when the ports are put in promiscuous mode, we also fail to update
PGID_BC towards the host pipe of the current protocol.
First issue means that felix_check_xtr_pkt() has to do extra work,
because it will not see only PTP packets, but also broadcasts. It needs
to dequeue these packets just to drop them.
Third issue is inconsequential, since PGID_BC is allocated from the
nonreserved multicast PGID space, and these PGIDs are conveniently
initialized to 0x7f (i.e. flood towards all ports except the CPU port
module). Broadcasts reach the NPI port via ocelot_init(), and reach the
tag_8021q CPU port via the hardware defaults.
Second issue is also inconsequential, because we fail both at disabling
and at enabling broadcast flooding on a port, so the defaults mentioned
above are preserved, and they are fine except for the performance impact.
Fixes: 7a29d220f4c0 ("net: dsa: felix: reimplement tagging protocol change with function pointers")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Since kconfig 'select' does not follow dependency chains, if symbol KSA
selects KSB, then KSA should also depend on the same symbols that KSB
depends on, in order to prevent Kconfig warnings and possible build
errors.
Change NET_DSA_SMSC_LAN9303_I2C and NET_DSA_SMSC_LAN9303_MDIO so that
they are limited to VLAN_8021Q if the latter is enabled. This prevents
the Kconfig warning:
WARNING: unmet direct dependencies detected for NET_DSA_SMSC_LAN9303
Depends on [m]: NETDEVICES [=y] && NET_DSA [=y] && (VLAN_8021Q [=m] || VLAN_8021Q [=m]=n)
Selected by [y]:
- NET_DSA_SMSC_LAN9303_I2C [=y] && NETDEVICES [=y] && NET_DSA [=y] && I2C [=y]
Fixes: 430065e26719 ("net: dsa: lan9303: add VLAN IDs to master device")
Signed-off-by: Randy Dunlap <[email protected]>
Cc: Andrew Lunn <[email protected]>
Cc: Vivien Didelot <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: Vladimir Oltean <[email protected]>
Cc: Juergen Borleis <[email protected]>
Cc: "David S. Miller" <[email protected]>
Cc: Eric Dumazet <[email protected]>
Cc: Jakub Kicinski <[email protected]>
Cc: Paolo Abeni <[email protected]>
Cc: Mans Rullgard <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
gswip_port_fdb_dump() reads the MAC bridge entries. The error message
should say "failed to read mac bridge entry". While here, also add the
index to the error print so humans can get to the cause of the problem
easier.
Acked-by: Hauke Mehrtens <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: Martin Blumenstingl <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The first N entries in priv->vlans are reserved for managing ports which
are not part of a bridge. Use priv->hw_info->max_ports to consistently
access per-bridge entries at index 7. Starting at
priv->hw_info->cpu_port (6) is harmless in this case because
priv->vlan[6].bridge is always NULL so the comparison result is always
false (which results in this entry being skipped).
Acked-by: Hauke Mehrtens <[email protected]>
Signed-off-by: Martin Blumenstingl <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The name, regs_size and overrides members in struct ksz_device are
unused. Hence remove it.
And host_mask is used in only place of ksz8795.c file, which can be
replaced by dev->info->cpu_ports
Signed-off-by: Arun Ramadoss <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch add the support for phylink_get_caps for ksz8795 and ksz9477
series switch. It updates the struct ksz_switch_chip with the details of
the internal phys and xmii interface. Then during the get_caps based on
the bits set in the structure, corresponding phy mode is set.
Signed-off-by: Arun Ramadoss <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
mib->cnt_ptr resetting is handled in multiple places as part of
port_init_cnt(). Hence moved mib->cnt_ptr code to ksz common layer
and removed from individual product files.
Signed-off-by: Prasanna Vengateshan <[email protected]>
Signed-off-by: Arun Ramadoss <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
ksz8795 and ksz9477 uses the same algorithm for copying the ethtool
strings. Hence moved to ksz_common to remove the redundant code.
Signed-off-by: Arun Ramadoss <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
ksz8795 and ksz9477 init function initializes the memory to dev->ports,
mib counters and assigns the ds real number of ports. Since both the
routines are same, moved the allocation of port memory to
ksz_switch_register after init.
Signed-off-by: Arun Ramadoss <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The ksz88xx family has one set of mib_names. The ksz87xx, ksz9477,
LAN937x based switches has one set of mib_names. In order to remove
redundant declaration, moved the struct mib_names to ksz_chip_data
structure.
Signed-off-by: Arun Ramadoss <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch perform the compatibility check for the device after the chip
detect is done. It is to prevent the mismatch between the device
compatible specified in the device tree and actual device found during
the detect. The ksz9477 device doesn't use any .data in the
of_device_id. But the ksz8795_spi uses .data for assigning the regmap
between 8830 family and 87xx family switch. Changed the regmap
assignment based on the chip_id from the .data.
Signed-off-by: Arun Ramadoss <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch moves the ksz_chip_data in ksz8795 and ksz9477 to ksz_common.
At present, the dev->chip_id is iterated with the ksz_chip_data and then
copy its value to the ksz_dev structure. These values are declared as
constant.
Instead of copying the values and referencing it, this patch update the
dev->info to the ksz_chip_data based on the chip_id in the init
function. And also update the ksz_chip_data values for the LAN937x based
switches.
Signed-off-by: Arun Ramadoss <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The port_cnt value in the structure is not used in the switch_init.
Instead it uses the fls(chip->cpu_port), this is due to one of port in
the ksz8794 unavailable. The cpu_port for the 8794 is 0x10, fls(0x10) =
5, hence updating it directly in the ksz_chip_data structure in order to
same with all the other switches in ksz8795.c and ksz9477.c files.
Signed-off-by: Arun Ramadoss <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Lock the regmap during the whole PHY register access routines in
rtl8366rb.
Signed-off-by: Alvin Šipraga <[email protected]>
Tested-by: Linus Walleij <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Currently the ocelot switch lib is unaware of the index of a struct
ocelot_port, since that is kept in the encapsulating structures of outer
drivers (struct dsa_port :: index, struct ocelot_port_private :: chip_port).
With the upcoming increase in complexity associated with assigning DSA
tag_8021q CPU ports to certain user ports, it becomes necessary for the
switch lib to be able to retrieve the index of a certain ocelot_port.
Therefore, introduce a new u8 to ocelot_port (same size as the chip_port
used by the ocelot switchdev driver) and rework the existing code to
populate and use it.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The error handling for the current tagging protocol change procedure is
a bit brittle (we dismantle the previous tagging protocol entirely
before setting up the new one). By identifying which parts of a tagging
protocol are unique to itself and which parts are shared with the other,
we can implement a protocol change procedure where error handling is a
bit more robust, because we start setting up the new protocol first, and
tear down the old one only after the setup of the specific and shared
parts succeeded.
The protocol change is a bit too open-coded too, in the area of
migrating host flood settings and MDBs. By identifying what differs
between tagging protocols (the forwarding masks for host flooding) we
can implement a more straightforward migration procedure which is
handled in the shared portion of the protocol change, rather than
individually by each protocol.
Therefore, a more structured approach calls for the introduction of a
structure of function pointers per tagging protocol. This covers setup,
teardown and the host forwarding mask. In the future it will also cover
how to prepare for a new DSA master.
The initial tagging protocol setup (at driver probe time) and the final
teardown (at driver removal time) are also adapted to call into the
structured methods of the specific protocol in current use. This is
especially relevant for teardown, where we previously called
felix_del_tag_protocol() only for the first CPU port. But by not
specifying which CPU port this is for, we gain more flexibility to
support multiple CPU ports in the future.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Ocelot switches support a single active CPU port at a time (at least as
a trapping destination, i.e. for control traffic). This is true
regardless of whether we are using the native copy-to-CPU-port-module
functionality, or a redirect action towards the software-defined
tag_8021q CPU port.
Currently we assume that the trapping destination in tag_8021q mode is
the first CPU port, yet in the future we may want to migrate the user
ports to the second CPU port.
For that to work, we need to make sure that the tag_8021q trapping
destination is a CPU port that is active, i.e. is used by at least some
user port on which the trap was added. Otherwise, we may end up
redirecting the traffic to a CPU port which isn't even up.
Note that due to the current design where we simply choose the CPU port
of the first port from the trap's ingress port mask, it may be that a
CPU port absorbes control traffic from user ports which aren't affine to
it as per user space's request. This isn't ideal, but is the lesser of
two evils. Following the user-configured affinity for traps would mean
that we can no longer reuse a single TCAM entry for multiple traps,
which is what we actually do for e.g. PTP. Either we duplicate and
deduplicate TCAM entries on the fly when user-to-CPU-port mappings
change (which is unnecessarily complicated), or we redirect trapped
traffic to all tag_8021q CPU ports if multiple such ports are in use.
The latter would have actually been nice, if it actually worked, but it
doesn't, since a OCELOT_MASK_MODE_REDIRECT action towards multiple ports
would not take PGID_SRC into consideration, and it would just duplicate
the packet towards each (CPU) port, leading to duplicates in software.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
DSA has not supported (and probably will not support in the future
either) independent tagging protocols per CPU port.
Different switch drivers have different requirements, some may need to
replicate some settings for each CPU port, some may need to apply some
settings on a single CPU port, while some may have to configure some
global settings and then some per-CPU-port settings.
In any case, the current model where DSA calls ->change_tag_protocol for
each CPU port turns out to be impractical for drivers where there are
global things to be done. For example, felix calls dsa_tag_8021q_register(),
which makes no sense per CPU port, so it suppresses the second call.
Let drivers deal with replication towards all CPU ports, and remove the
CPU port argument from the function prototype.
Signed-off-by: Vladimir Oltean <[email protected]>
Acked-by: Luiz Angelo Daros de Luca <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
At the time - commit 7569459a52c9 ("net: dsa: manage flooding on the CPU
ports") - not introducing a dedicated switch callback for host flooding
made sense, because for the only user, the felix driver, there was
nothing different to do for the CPU port than set the flood flags on the
CPU port just like on any other bridge port.
There are 2 reasons why this approach is not good enough, however.
(1) Other drivers, like sja1105, support configuring flooding as a
function of {ingress port, egress port}, whereas the DSA
->port_bridge_flags() function only operates on an egress port.
So with that driver we'd have useless host flooding from user ports
which don't need it.
(2) Even with the felix driver, support for multiple CPU ports makes it
difficult to piggyback on ->port_bridge_flags(). The way in which
the felix driver is going to support host-filtered addresses with
multiple CPU ports is that it will direct these addresses towards
both CPU ports (in a sort of multicast fashion), then restrict the
forwarding to only one of the two using the forwarding masks.
Consequently, flooding will also be enabled towards both CPU ports.
However, ->port_bridge_flags() gets passed the index of a single CPU
port, and that leaves the flood settings out of sync between the 2
CPU ports.
This is to say, it's better to have a specific driver method for host
flooding, which takes the user port as argument. This solves problem (1)
by allowing the driver to do different things for different user ports,
and problem (2) by abstracting the operation and letting the driver do
whatever, rather than explicitly making the DSA core point to the CPU
port it thinks needs to be touched.
This new method also creates a problem, which is that cross-chip setups
are not handled. However I don't have hardware right now where I can
test what is the proper thing to do, and there isn't hardware compatible
with multi-switch trees that supports host flooding. So it remains a
problem to be tackled in the future.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
For symmetry with host FDBs and MDBs where the indirection is now
handled outside the ocelot switch lib, do the same for bridge port
flags (unicast/multicast/broadcast flooding).
The only caller of the ocelot switch lib which uses the NPI port is the
Felix DSA driver.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
For symmetry with host FDBs where the indirection is now handled outside
the ocelot switch lib, do the same for host MDB entries. The only caller
of the ocelot switch lib which uses the NPI port is the Felix DSA driver.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
I remembered why we had the host FDB migration procedure in place.
It is true that host FDB entry migration can be done by changing the
value of PGID_CPU, but the problem is that only host FDB entries learned
while operating in NPI mode go to PGID_CPU. When the CPU port operates
in tag_8021q mode, the FDB entries are learned towards the unicast PGID
equal to the physical port number of this CPU port, bypassing the
PGID_CPU indirection.
So host FDB entries learned in tag_8021q mode are not migrated any
longer towards the NPI port.
Fix this by extracting the NPI port -> PGID_CPU redirection from the
ocelot switch lib, moving it to the Felix DSA driver, and applying it
for any CPU port regardless of its kind (NPI or tag_8021q).
Fixes: a51c1c3f3218 ("net: dsa: felix: stop migrating FDBs back and forth on tag proto change")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
No conflicts.
Build issue in drivers/net/ethernet/sfc/ptp.c
54fccfdd7c66 ("sfc: efx_default_channel_type APIs can be static")
49e6123c65da ("net: sfc: fix memory leak due to ptp channel")
https://lore.kernel.org/all/[email protected]/
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
After commit 2d1f90f9ba83 ("net: dsa/bcm_sf2: fix incorrect usage of
state->link") the interface suspend path would call our mac_link_down()
call back which would forcibly set the link down, thus preventing
Wake-on-LAN packets from reaching our management port.
Fix this by looking at whether the port is enabled for Wake-on-LAN and
not clearing the link status in that case to let packets go through.
Fixes: 2d1f90f9ba83 ("net: dsa/bcm_sf2: fix incorrect usage of state->link")
Signed-off-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Switches using the Lynx PCS driver support 1000base-X optical SFP
modules. Accept this interface type on a port.
Signed-off-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The felix driver is the only user of dsa_port_walk_mdbs(), and there
isn't even a good reason for it, considering that the host MDB entries
are already saved by the ocelot switch lib in the ocelot->multicast list.
Rewrite the multicast entry migration procedure around the
ocelot->multicast list so we can delete dsa_port_walk_mdbs().
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
I just realized we don't need to migrate the host-filtered FDB entries
when the tagging protocol changes from "ocelot" to "ocelot-8021q".
Host-filtered addresses are learned towards the PGID_CPU "multicast"
port group, reserved by software, which contains BIT(ocelot->num_phys_ports).
That is the "special" port entry in the analyzer block for the CPU port
module.
In "ocelot" mode, the CPU port module's packets are redirected to the
NPI port.
In "ocelot-8021q" mode, felix_8021q_cpu_port_init() does something funny
anyway, and changes PGID_CPU to stop pointing at the CPU port module and
start pointing at the physical port where the DSA master is attached.
The fact that we can alter the destination of packets learned towards
PGID_CPU without altering the MAC table entries themselves means that it
is pointless to walk through the FDB entries, forget that they were
learned towards PGID_CPU, and re-learn them towards the "unicast" PGID
associated with the physical port connected to the DSA master. We can
let the PGID_CPU value change simply alter the destination of the
host-filtered unicast packets in one fell swoop.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|