aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/dsa/microchip
AgeCommit message (Collapse)AuthorFilesLines
2022-12-19net: dsa: microchip: remove IRQF_TRIGGER_FALLING in request_threaded_irqArun Ramadoss1-2/+1
KSZ swithes used interrupts for detecting the phy link up and down. During registering the interrupt handler, it used IRQF_TRIGGER_FALLING flag. But this flag has to be retrieved from device tree instead of hard coding in the driver, so removing the flag. Fixes: ff319a644829 ("net: dsa: microchip: move interrupt handling logic from lan937x to ksz_common") Reported-by: Christian Eggers <[email protected]> Signed-off-by: Arun Ramadoss <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2022-12-08net: dsa: microchip: add stats64 support for ksz8 series of switchesOleksij Rempel2-0/+88
Add stats64 support for ksz8xxx series of switches. Signed-off-by: Oleksij Rempel <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2022-12-07net: dsa: microchip: ksz8: move all DSA configurations to one locationOleksij Rempel1-10/+10
To make the code more comparable to KSZ9477 code, move DSA configurations to the same location. Signed-off-by: Oleksij Rempel <[email protected]> Acked-by: Arun Ramadoss <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: Paolo Abeni <[email protected]>
2022-12-07net: dsa: microchip: enable MTU normalization for KSZ8795 and KSZ9477 ↵Oleksij Rempel2-0/+4
compatible switches KSZ8795 and KSZ9477 compatible series of switches use global max frame size configuration register. So, enable MTU normalization for this reason. Signed-off-by: Oleksij Rempel <[email protected]> Acked-by: Arun Ramadoss <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: Paolo Abeni <[email protected]>
2022-12-07net: dsa: microchip: ksz8: add MTU configuration supportOleksij Rempel5-2/+66
Make MTU configurable on KSZ87xx and KSZ88xx series of switches. Before this patch, pre-configured behavior was different on different switch series, due to opposite meaning of the same bit: - KSZ87xx: Reg 4, Bit 1 - if 1, max frame size is 1532; if 0 - 1514 - KSZ88xx: Reg 4, Bit 1 - if 1, max frame size is 1514; if 0 - 1532 Since the code was telling "... SW_LEGAL_PACKET_DISABLE, true)", I assume, the idea was to set max frame size to 1532. With this patch, by setting MTU size 1500, both switch series will be configured to the 1532 frame limit. This patch was tested on KSZ8873. Signed-off-by: Oleksij Rempel <[email protected]> Acked-by: Arun Ramadoss <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: Paolo Abeni <[email protected]>
2022-12-07net: dsa: microchip: add ksz_rmw8() functionOleksij Rempel1-0/+5
Add ksz_rmw8(), it will be used in the next patch. Signed-off-by: Oleksij Rempel <[email protected]> Acked-by: Arun Ramadoss <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: Paolo Abeni <[email protected]>
2022-12-07net: dsa: microchip: do not store max MTU for all portsOleksij Rempel2-10/+5
If we have global MTU configuration, it is enough to configure it on CPU port only. Signed-off-by: Oleksij Rempel <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: Paolo Abeni <[email protected]>
2022-12-07net: dsa: microchip: move max mtu to one locationOleksij Rempel5-14/+19
There are no HW specific registers, so we can process all of them in one location. Signed-off-by: Oleksij Rempel <[email protected]> Tested-by: Arun Ramadoss <[email protected]> (KSZ9893 and LAN937x) Signed-off-by: Paolo Abeni <[email protected]>
2022-11-23net: dsa: microchip: ksz9477: Convert to i2c's .probe_new()Uwe Kleine-König1-3/+2
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by: Uwe Kleine-König <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2022-11-22net: dsa: modularize DSA_TAG_PROTO_NONEVladimir Oltean1-0/+1
There is no reason that I can see why the no-op tagging protocol should be registered manually, so make it a module and make all drivers which have any sort of reference to DSA_TAG_PROTO_NONE select it. Note that I don't know if ksz_get_tag_protocol() really needs this, or if it's just the logic which is poorly written. All switches seem to have their own tagging protocol, and DSA_TAG_PROTO_NONE is just a fallback that never gets used. Signed-off-by: Vladimir Oltean <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2022-11-09net: dsa: microchip: add dev_err_probe in probe functionsRakesh Sankaranarayanan3-15/+10
Probe functions uses normal dev_err() to check error conditions and print messages. Replace dev_err() with dev_err_probe() to have more standardized format and error logging. Signed-off-by: Rakesh Sankaranarayanan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-11-09net: dsa: microchip: ksz8563: Add number of port irqRakesh Sankaranarayanan1-0/+1
KSZ8563 have three port interrupts: PTP, PHY and ACL. Add port_nirq as 3 for KSZ8563 inside ksz_chip_data. Signed-off-by: Rakesh Sankaranarayanan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-11-09net: dsa: microchip: add error checking for ksz_pwriteRakesh Sankaranarayanan1-1/+5
Add status validation for port register write inside lan937x_change_mtu. ksz_pwrite and ksz_pread api's are updated with return type int (Reference patch mentioned below). Update lan937x_change_mtu with status validation for ksz_pwrite16(). Link: https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/ Signed-off-by: Rakesh Sankaranarayanan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-11-09net: dsa: microchip: add irq in i2c probeRakesh Sankaranarayanan1-0/+2
add device irq in i2c probe function. Signed-off-by: Rakesh Sankaranarayanan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-11-09net: dsa: microchip: add ksz9563 in ksz_switch_ops and select based on ↵Rakesh Sankaranarayanan5-5/+38
compatible string Add KSZ9563 inside ksz_switch_chips structure with port_nirq as 3. KSZ9563 use KSZ9893 switch parameters but port_nirq count is 3 for KSZ9563 whereas 2 for KSZ9893. Add KSZ9563 inside ksz_switch_chips as a separate member and from device tree map compatible string into KSZ9563 inside ksz_spi.c and ksz9477_i2c.c. Global Chip ID 1 and 2 registers read value 9893, select sku based on Global Chip ID 4 Register which read 0x1c for KSZ9563. Signed-off-by: Rakesh Sankaranarayanan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-10-04Merge tag 'i2c-for-6.1-rc1' of ↵Linus Torvalds1-3/+1
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c updates from Wolfram Sang: - 'remove' callback converted to return void. Big change with trivial fixes all over the tree. Other subsystems depending on this change have been asked to pull an immutable topic branch for this. - new driver for Microchip PCI1xxxx switch - heavy refactoring of the Mellanox BlueField driver - we prefer async probe in the i801 driver now - the rest is usual driver updates (support for more SoCs, some refactoring, some feature additions) * tag 'i2c-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits) i2c: pci1xxxx: prevent signed integer overflow i2c: acpi: Replace zero-length array with DECLARE_FLEX_ARRAY() helper i2c: i801: Prefer async probe i2c: designware-pci: Use standard pattern for memory allocation i2c: designware-pci: Group AMD NAVI quirk parts together i2c: microchip: pci1xxxx: Add driver for I2C host controller in multifunction endpoint of pci1xxxx switch docs: i2c: slave-interface: return errno when handle I2C_SLAVE_WRITE_REQUESTED i2c: mlxbf: remove device tree support i2c: mlxbf: support BlueField-3 SoC i2c: cadence: Add standard bus recovery support i2c: mlxbf: add multi slave functionality i2c: mlxbf: support lock mechanism macintosh/ams: Adapt declaration of ams_i2c_remove() to earlier change i2c: riic: Use devm_platform_ioremap_resource() i2c: mlxbf: remove IRQF_ONESHOT dt-bindings: i2c: rockchip: add rockchip,rk3128-i2c dt-bindings: i2c: renesas,rcar-i2c: Add r8a779g0 support i2c: tegra: Add GPCDMA support i2c: scmi: Convert to be a platform driver i2c: rk3x: Add rv1126 support ...
2022-09-27Merge branch 'master' into i2c/for-mergewindowWolfram Sang1-4/+0
2022-09-26net: dsa: microchip: ksz9477: remove unnecessary i2c_set_clientdata()Yang Yingliang1-2/+0
Remove unnecessary i2c_set_clientdata() in ->remove(), the driver_data will be set to NULL in device_unbind_cleanup() after calling ->remove(). Signed-off-by: Yang Yingliang <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2022-09-26net: dsa: microchip: use common irq routines for girq and pirqArun Ramadoss2-192/+81
The global port interrupt routines and individual ports interrupt routines has similar implementation except the mask & status register and number of nested irqs in them. The mask & status register and pointer to ksz_device is added to ksz_irq and uses the ksz_irq as irq_chip_data. Signed-off-by: Arun Ramadoss <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2022-09-26net: dsa: microchip: move interrupt handling logic from lan937x to ksz_commonArun Ramadoss3-426/+433
To support the phy link detection through interrupt method for ksz9477 based switch, the interrupt handling routines are moved from lan937x_main.c to ksz_common.c. The only changes made are functions names are prefixed with ksz_ instead of lan937x_. Signed-off-by: Arun Ramadoss <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2022-09-26net: dsa: microchip: lan937x: return zero if mdio node not presentArun Ramadoss1-4/+2
Currently, if the mdio node is not present in the dts file then lan937x_mdio_register return -ENODEV and entire probing process fails. To make the mdio_register generic for all ksz series switches and to maintain back-compatibility with existing dts file, return -ENODEV is replaced with return 0. Signed-off-by: Arun Ramadoss <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2022-09-26net: dsa: microchip: enable phy interrupts only if interrupt enabled in dtsArun Ramadoss1-5/+8
In the lan937x_mdio_register function, phy interrupts are enabled irrespective of irq is enabled in the switch. Now, the check is added to enable the phy interrupt only if the irq is enabled in the switch. Signed-off-by: Arun Ramadoss <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2022-09-26net: dsa: microchip: determine number of port irq based on switch typeArun Ramadoss3-3/+12
Currently the number of port irqs is hard coded for the lan937x switch as 6. In order to make the generic interrupt handler for ksz switches, number of port irq supported by the switch is added to the ksz_chip_data. It is 4 for ksz9477, 2 for ksz9897 and 3 for ksz9567. Signed-off-by: Arun Ramadoss <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2022-09-22net: dsa: microchip: remove unnecessary set_drvdata()Yang Yingliang2-4/+0
Remove unnecessary set_drvdata(NULL) function in ->remove(), the driver_data will be set to NULL in device_unbind_cleanup() after calling ->remove(). Signed-off-by: Yang Yingliang <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2022-09-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski1-4/+0
drivers/net/ethernet/freescale/fec.h 7b15515fc1ca ("Revert "fec: Restart PPS after link state change"") 40c79ce13b03 ("net: fec: add stop mode support for imx8 platform") https://lore.kernel.org/all/[email protected]/ drivers/pinctrl/pinctrl-ocelot.c c297561bc98a ("pinctrl: ocelot: Fix interrupt controller") 181f604b33cd ("pinctrl: ocelot: add ability to be used in a non-mmio configuration") https://lore.kernel.org/all/[email protected]/ tools/testing/selftests/drivers/net/bonding/Makefile bbb774d921e2 ("net: Add tests for bonding and team address list management") 152e8ec77640 ("selftests/bonding: add a test for bonding lladdr target") https://lore.kernel.org/all/[email protected]/ drivers/net/can/usb/gs_usb.c 5440428b3da6 ("can: gs_usb: gs_can_open(): fix race dev->can.state condition") 45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support") https://lore.kernel.org/all/[email protected]/ Signed-off-by: Jakub Kicinski <[email protected]>
2022-09-20net: dsa: microchip: lan937x: fix maximum frame length checkRakesh Sankaranarayanan1-4/+0
Maximum frame length check is enabled in lan937x switch on POR, But it is found to be disabled on driver during port setup operation. Due to this, packets are not dropped when transmitted with greater than configured value. For testing, setup made for lan1->lan2 transmission and configured lan1 interface with a frame length (less than 1500 as mentioned in documentation) and transmitted packets with greater than configured value. Expected no packets at lan2 end, but packets observed at lan2. Based on the documentation, packets should get discarded if the actual packet length doesn't match the frame length configured. Frame length check should be disabled only for cascaded ports due to tailtags. This feature was disabled on ksz9477 series due to ptp issue, which is not in lan937x series. But since lan937x took ksz9477 as base, frame length check disabled here as well. Patch added to remove this portion from port setup so that maximum frame length check will be active for normal ports. Fixes: 55ab6ffaf378 ("net: dsa: microchip: add DSA support for microchip LAN937x") Signed-off-by: Rakesh Sankaranarayanan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Paolo Abeni <[email protected]>
2022-09-19net: dsa: microchip: lan937x: fix reference count leak in ↵Sun Ke1-1/+3
lan937x_mdio_register() This node pointer is returned by of_find_compatible_node() with refcount incremented in this function. of_node_put() on it before exitting this function. Fixes: c9cd961c0d43 ("net: dsa: microchip: lan937x: add interrupt support for port phy link") Signed-off-by: Sun Ke <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2022-09-16net: dsa: microchip: add the support for set_ageing_timeArun Ramadoss8-1/+67
KSZ9477 has the 11 bit ageing count value which is split across the two registers. And LAN937x has the 20 bit ageing count which is also split into two registers. Each count in the registers represents 1 second. This patch add the support for ageing time for KSZ9477 and LAN937x series of switch. Signed-off-by: Arun Ramadoss <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-09-16Merge tag 'v6.0-rc5' into i2c/for-mergewindowWolfram Sang3-8/+79
Linux 6.0-rc5
2022-09-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netPaolo Abeni1-6/+24
drivers/net/ethernet/freescale/fec.h 7d650df99d52 ("net: fec: add pm_qos support on imx6q platform") 40c79ce13b03 ("net: fec: add stop mode support for imx8 platform") Signed-off-by: Paolo Abeni <[email protected]>
2022-09-07net: dsa: microchip: add regmap_range for KSZ9896 chipRomain Naour1-0/+215
Add register validation for KSZ9896. Signed-off-by: Romain Naour <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-09-07net: dsa: microchip: ksz9477: remove 0x033C and 0x033D addresses from ↵Romain Naour1-1/+2
regmap_access_tables According to the KSZ9477S datasheet, there is no global register at 0x033C and 0x033D addresses. Signed-off-by: Romain Naour <[email protected]> Cc: Oleksij Rempel <[email protected]> Tested-by: Oleksij Rempel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-09-07net: dsa: microchip: add KSZ9896 to KSZ9477 I2C driverRomain Naour1-0/+4
Add support for the KSZ9896 6-port Gigabit Ethernet Switch to the ksz9477 driver. The KSZ9896 supports both SPI (already in) and I2C. Signed-off-by: Romain Naour <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-09-07net: dsa: microchip: add KSZ9896 switch supportRomain Naour3-0/+39
Add support for the KSZ9896 6-port Gigabit Ethernet Switch to the ksz9477 driver. Although the KSZ9896 is already listed in the device tree binding documentation since a1c0ed24fe9b (dt-bindings: net: dsa: document additional Microchip KSZ9477 family switches) the chip id (0x00989600) is not recognized by ksz_switch_detect() and rejected by the driver. The KSZ9896 is similar to KSZ9897 but has only one configurable MII/RMII/RGMII/GMII cpu port. Signed-off-by: Romain Naour <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-09-05net: dsa: microchip: lan937x: add interrupt support for port phy linkArun Ramadoss6-4/+399
This patch enables the interrupts for internal phy link detection for LAN937x. The interrupt enable bits are active low. There is global interrupt mask for each port. And each port has the individual interrupt mask for TAS. QCI, SGMII, PTP, PHY and ACL. The first level of interrupt domain is registered for global port interrupt and second level of interrupt domain for the individual port interrupts. The phy interrupt is enabled in the lan937x_mdio_register function. Interrupt from which port is raised will be detected based on the interrupt host data. Signed-off-by: Arun Ramadoss <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-09-05net: dsa: microchip: lan937x: clear the POR_READY_INT status bitArun Ramadoss1-0/+4
In the lan937x_reset_switch(), it masks all the switch and port registers. In the Global_Int_status register, POR ready bit is write 1 to clear bit and all other bits are read only. So, this patch clear the por_ready_int status bit by writing 1. Signed-off-by: Arun Ramadoss <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-09-05net: dsa: microchip: add reference to ksz_device inside the ksz_portArun Ramadoss2-0/+7
struct ksz_port doesn't have reference to ksz_device as of now. In order to find out from which port interrupt has triggered, we need to pass the struct ksz_port as a host data. When the interrupt is triggered, we can get the port from which interrupt triggered, but to identify it is phy interrupt we have to read status register. The regmap structure for accessing the device register is present in the ksz_device struct. To access the ksz_device from the ksz_port, the reference is added to it with port number as well. Signed-off-by: Arun Ramadoss <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-09-03net: dsa: microchip: fix kernel oops on ksz8 switchesOleksij Rempel1-6/+24
After driver refactoring we was running ksz9477 specific CPU port configuration on ksz8 family which ended with kernel oops. So, make sure we run this code only on ksz9477 compatible devices. Tested on KSZ8873 and KSZ9477. Fixes: da8cd08520f3 ("net: dsa: microchip: add support for common phylink mac link up") Signed-off-by: Oleksij Rempel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-08-31net: dsa: microchip: remove IS_9893 flagOleksij Rempel3-8/+2
Use chip_id as other places of this code do it Signed-off-by: Oleksij Rempel <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-08-31net: dsa: microchip: remove unused sgmii variableOleksij Rempel2-6/+0
This variable is not used. So, remove it. Signed-off-by: Oleksij Rempel <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-08-31net: dsa: microchip: ksz9477: remove unused "on" variableOleksij Rempel1-2/+0
This variable is not used on ksz9477 side. Remove it. Signed-off-by: Oleksij Rempel <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-08-31net: dsa: microchip: remove unused port phy variableOleksij Rempel3-7/+0
This variable is unused. So, drop it. Signed-off-by: Oleksij Rempel <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-08-31net: dsa: microchip: ksz9477: use internal_phy instead of phy_port_cntOleksij Rempel1-13/+7
With code refactoring was introduced new variable internal_phy. Let's use it. Signed-off-by: Oleksij Rempel <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-08-31net: dsa: microchip: add regmap_range for KSZ9477 chipOleksij Rempel1-0/+272
Add register validation for KSZ9477 Signed-off-by: Oleksij Rempel <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-08-31net: dsa: microchip: ksz9477: remove MII_CTRL1000 check from ksz9477_w_phy()Oleksij Rempel1-4/+0
The reason why PHYlib may access MII_CTRL1000 on the chip without GBit support is only if chip provides wrong information about extended caps register. This issue is now handled by ksz9477_r_phy_quirks() With proper regmap_ranges provided for all chips we will be able to catch this kind of bugs any way. So, remove this sanity check. Signed-off-by: Oleksij Rempel <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-08-31net: dsa: microchip: add regmap_range for KSZ8563 chipOleksij Rempel1-0/+121
Add register validation for KSZ8563. Signed-off-by: Oleksij Rempel <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-08-31net: dsa: microchip: add support for regmap_access_tablesOleksij Rempel2-4/+45
This is complex driver with support for different chips with different layouts. To detect at least some bugs earlier, we should validate register accesses by using regmap_access_table support. Signed-off-by: Oleksij Rempel <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-08-31net: dsa: microchip: KSZ9893: do not write to not supported Output Clock ↵Oleksij Rempel1-0/+5
Control Register This issue was detected after adding regmap register access validation. KSZ9893 compatible chips do not have "Output Clock Control Register 0x0103". So, avoid writing to it. Signed-off-by: Oleksij Rempel <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-08-31net: dsa: microchip: ksz8795: add error handling to ksz8_r/w_phyOleksij Rempel1-21/+81
Now ksz_pread/ksz_pwrite can return error value. So, make use of it. Signed-off-by: Oleksij Rempel <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2022-08-31net: dsa: microchip: ksz9477: add error handling to ksz9477_r/w_phyOleksij Rempel1-5/+7
Now ksz_pread/ksz_pwrite can return error value. So, make use of it. Signed-off-by: Oleksij Rempel <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.