| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The newly added ektf2127 driver uses the SIMPLE_DEV_PM_OPS macro
to conditionally refer to the resume/suspend functions, which
causes a warning when CONFIG_PM_SLEEP is disabled:
drivers/input/touchscreen/ektf2127.c:168:12: error: 'ektf2127_resume' defined but not used [-Werror=unused-function]
drivers/input/touchscreen/ektf2127.c:156:12: error: 'ektf2127_suspend' defined but not used [-Werror=unused-function]
We could either put these functions inside of an #ifdef or
add __maybe_unused annotations. This uses the second approach,
which is generally more foolproof.
Fixes: 9ca5bf5029b6 ("Input: add support for Elan eKTF2127 touchscreen controller")
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"One small change to make joydev (which is used by older games) to bind
to devices that export Z axis but not X or Y (such as TRC rudder)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: joydev - recognize devices with Z axis as joysticks
|
|
Current implementation of joydev's input_device_id table recognizes only
devices with ABS_X, ABS_WHEEL or ABS_THROTTLE axes as joysticks.
There are joystick devices that do not have those axes, for example TRC
Rudder device. The device in question has ABS_Z, ABS_RX and ABS_RY axes
causing it not being detected as joystick.
This patch adds ABS_Z to the input_device_id list allowing devices with
ABS_Z axis to be detected correctly.
Signed-off-by: Ville Ranki <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Current code uses devm_input_allocate_device() so don't explicitly call
input_free_device if input_register_device fails.
Signed-off-by: Axel Lin <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
This adds a driver for the Elan eKTF2127 touchscreen controller,
which speaks an i2c protocol which is distinctly different from
the already supported eKTH controllers.
Signed-off-by: Michel Verlaan <[email protected]>
Signed-off-by: Siebren Vroegindeweij <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"Just a fix up for the firmware handling to the Silead driver (which is
a new driver in this release)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: silead_gsl1680 - use "silead/" prefix for firmware loading
Input: silead_gsl1680 - document firmware-name, fix implementation
|
|
The Pulse-Eight USB CEC adapter is a usb device that shows up as a ttyACM0
device. It requires that you run inputattach in order to communicate with
it via serio.
This all works well, but it would be nice to have a udev rule to
automatically start inputattach. That too works OK, but the problem comes
when the USB device is unplugged: the tty hangup is never handled by the
serio framework so the inputattach utility never exits and you have to kill
it manually.
By adding this hangup callback the inputattach utility now properly exits
as soon as the USB device is unplugged.
The udev rule I used on my Debian sid system is:
SUBSYSTEM=="tty", KERNEL=="ttyACM[0-9]*", ATTRS{idVendor}=="2548", ATTRS{idProduct}=="1002", ACTION=="add", TAG+="systemd", ENV{SYSTEMD_WANTS}+="pulse8-cec-inputattach@%k.service"
And /etc/systemd/system/[email protected] is as follows:
===============================================================
[Unit]
Description=inputattach for pulse8-cec device on %I
[Service]
Type=simple
ExecStart=/usr/local/bin/inputattach --pulse8-cec /dev/%I
KillMode=process
===============================================================
Signed-off-by: Hans Verkuil <[email protected]>
Tested-by: Hans Verkuil <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Add copyright lines for Zodiac who paid for the V4L touch work.
Signed-off-by: Nick Dyer <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
|
|
The newly added debug mode for the synaptics-rmi4 driver relies on
the v4l2 interface and vb2_vmalloc, but those might be configured
as loadable modules when the driver itself is built-in, resulting
in a link failure:
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_remove':
rmi_f54.c:(.text.rmi_f54_remove+0x14): undefined reference to `video_unregister_device'
rmi_f54.c:(.text.rmi_f54_remove+0x20): undefined reference to `v4l2_device_unregister'
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_vidioc_s_input':
rmi_f54.c:(.text.rmi_f54_vidioc_s_input+0x10): undefined reference to `video_devdata'
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_vidioc_g_input':
rmi_f54.c:(.text.rmi_f54_vidioc_g_input+0x10): undefined reference to `video_devdata'
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_vidioc_fmt':
rmi_f54.c:(.text.rmi_f54_vidioc_fmt+0x10): undefined reference to `video_devdata'
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_vidioc_enum_input':
rmi_f54.c:(.text.rmi_f54_vidioc_enum_input+0x10): undefined reference to `video_devdata'
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_vidioc_querycap':
...
The best workaround I could come up with is to disallow the debug
mode unless it's actually possible to call it.
Fixes: 3a762dbd5347 ("[media] Input: synaptics-rmi4 - add support for F54 diagnostics")
Signed-off-by: Arnd Bergmann <[email protected]>
Acked-by: Nick Dyer <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
|
|
The newnly added debug mode for the atmel_mxt_ts driver relies on
the v4l2 interface and vb2_vmalloc, but those might be configured
as loadable modules when the driver itself is built-in, resulting
in a link failure:
drivers/input/touchscreen/atmel_mxt_ts.o: In function `mxt_vidioc_querycap':
atmel_mxt_ts.c:(.text.mxt_vidioc_querycap+0x10): undefined reference to `video_devdata'
drivers/input/touchscreen/atmel_mxt_ts.o: In function `mxt_buffer_queue':
atmel_mxt_ts.c:(.text.mxt_buffer_queue+0x20): undefined reference to `vb2_plane_vaddr'
atmel_mxt_ts.c:(.text.mxt_buffer_queue+0x164): undefined reference to `vb2_buffer_done'
drivers/input/touchscreen/atmel_mxt_ts.o: In function `mxt_free_object_table':
atmel_mxt_ts.c:(.text.mxt_free_object_table+0x18): undefined reference to `video_unregister_device'
atmel_mxt_ts.c:(.text.mxt_free_object_table+0x20): undefined reference to `v4l2_device_unregister'
The best workaround I could come up with is to disallow the debug
mode unless it's actually possible to call it.
Fixes: ecfdd7e2660e ("[media] Input: atmel_mxt_ts - output diagnostic debug via V4L2 device")
Signed-off-by: Arnd Bergmann <[email protected]>
Acked-by: Nick Dyer <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
|
|
The silead touch-controller ICs use a different firmware per digitizer /
tablet model. So there are going to be quite a few of then and they really
should be under a separate subdir.
This commit prefixes the default firmware names with "silead/" just like
we are already doing for devicetree specified firmware names.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The driver has supported touchscreen-fw-name to specify the firmware to
load since it has been merged, but this was omitted from the dt-binding
documentation.
During review of adding touchscreen-fw-name to the binding documentation
it was brought up that there is a standard property name called
"firmware-name" for this, which should be used.
Since there are no users of touchscreen-fw-name yet, this commit
adds documentation of "firmware-name" to the dt-binding documentation
and switches the driver over to use this.
This commit also makes the driver add a "silead/" prefix to the
firmware name from dt before calling request_firmware. That the
firmware files are stored under /lib/firmware/silead under Linux
is an implementation detail and does not belong in devicetree.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The power button found in tps65217 device is very similar to the tps65218,
so let's enhance the driver to support both variants.
This driver enables us to use tps65217's power button as KEY_POWER on
am335x boards (directly connected button in chiliboard, accessible pin
via expansion header in beaglebone). This patch has been tested with
chiliboard.
Signed-off-by: Marcin Niestroj <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Switch the jornada720 touchscreen driver to obtain its gpio from
the platform device via gpiolib and derive the interrupt from the
GPIO, rather than via a hard-coded interrupt number obtained from
the mach/irqs.h and mach/hardware.h headers.
Tested-by: Adam Wysocki <[email protected]>
Signed-off-by: Russell King <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The Jornada720 keyboard driver does not make use of anything from the
mach/hardware.h header, so this header can be removed.
Tested-by: Adam Wysocki <[email protected]>
Signed-off-by: Russell King <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
We get 1 warning when building kernel with W=1:
drivers/input/mouse/focaltech.c:393:6: warning: no previous prototype for 'focaltech_set_resolution' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
So this patch marks it 'static'.
Signed-off-by: Baoyou Xie <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The spec says that flash erase time is 30ms typical/200ms max, so let's
replace current 50ms wait with 200ms to avoid potential failures.
Signed-off-by: HungNien Chen <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
We want the fixes in here for merging and testing.
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Many modules call misc_register and misc_deregister in its module init
and exit methods without any additional code. This ends up being
boilerplate. This patch adds helper macro module_misc_device(), that
replaces module_init()/ module_exit() with template functions.
This patch also converts drivers to use new macro.
Change since v1:
Add device.h include in miscdevice.h as module_driver macro was not
available from other include files in some architectures.
Signed-off-by: PrasannaKumar Muralidharan <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Because events other that keyboard ones will be handled by now on by
other drivers, stop directly handling interrupts and instead listen to
the new notifier in the MFD driver.
Signed-off-by: Vic Yang <[email protected]>
Signed-off-by: Tomeu Vizoso <[email protected]>
Tested-by: Enric Balletbo i Serra <[email protected]>
Acked-by: Dmitry Torokhov <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
|
|
Add a driver to read group of GPIO lines and provide its status as a
numerical value as input event to the system. This will help in
interfacing devices, that can be connected over GPIOs, that provide
input to the system by driving GPIO lines connected to them like a
rotary dial or a switch.
For example, a rotary switch can be connected to four GPIO lines. The
status of the GPIO lines reflect the actual position of the rotary
switch dial. For example, if dial points to 9, then the four GPIO lines
connected to the switch will read HLLH(0b'1001 = 9). This value
can be reported as an ABS_* event to the input subsystem.
Signed-off-by: Vignesh R <[email protected]>
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
A common way of multiplexing buttons on a single input in cheap devices is
to use a resistor ladder on an ADC. This driver supports that configuration
by polling an ADC channel provided by IIO.
Acked-by: Jonathan Cameron <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov:
"Simply small driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ads7846 - remove redundant regulator_disable call
Input: synaptics-rmi4 - fix register descriptor subpacket map construction
Input: tegra-kbc - fix inverted reset logic
Input: silead - use devm_gpiod_get
Input: i8042 - set up shared ps2_cmd_mutex for AUX ports
|
|
According to the kernel's guidelines, let's directly include the
workqueue functions we use.
Signed-off-by: Martin Kepplinger <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
We use hw version to construct name of file holding touchscreen firmware,
so let's try reading it even if touchscreen initialization fails (the
firmware supports reading product/hardware id even when device is in
recovery/boot mode).
Signed-off-by: Johnny Chuang <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
alloc_ordered_workqueue() replaces deprecated
create_singlethread_workqueue().
It queues work items via &wm->ts_reader and &wm->pen_event_work which map
to wm97xx_pen_irq_worker (handles a pen down interrupt) and
wm97xx_ts_reader (the touchscreen sample reader) respectively. Hence, an
ordered dedicated workqueue has been used.
Signed-off-by: Bhaktipriya Shridhar <[email protected]>
Acked-by: Charles Keepax <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The workqueue "workqueue" has a single workitem(&priv->work) and hence
doesn't require ordering. Also, it is not being used on a memory reclaim
path. Hence, the singlethreaded workqueue has been replaced with the use
of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Workitem is sync cancelled in mc13783_ts_remove() to ensure that there
are no workitems pending when the driver is disconnected.
Signed-off-by: Bhaktipriya Shridhar <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
alloc_ordered_workqueue() replaces the deprecated
create_singlethread_workqueue().
There are multiple work items on the work queue viz
&priv->dev3_register_work, &priv->recalib_wq, &psmouse->resync_work,
which require execution ordering. Hence, an ordered workqueue has been
used.
The workqueue is not being used on a memory reclaim path. Hence,
WQ_MEM_RECLAIM has not been set.
Signed-off-by: Bhaktipriya Shridhar <[email protected]>
Acked-by: Tejun Heo <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The device hardware is always running at 60 FPS, so report this both via
PARM_IOCTL and ENUM_FRAMEINTERVALS.
[[email protected]: fix suspect indent checkpatch warning]
[[email protected]: fix a trivial merge conflict]
Signed-off-by: Martin Kaltenbrunner <[email protected]>
Signed-off-by: Florian Echtler <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
|
|
Support both V4L2_TCH_FMT_TU08 and V4L2_PIX_FMT_GREY for backwards
compatibility.
Signed-off-by: Nick Dyer <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Acked-by: Dmitry Torokhov <[email protected]>
|
|
Function 54 implements access to various RMI4 diagnostic features.
This patch adds support for retrieving this data. It registers a V4L2
device to output the data to user space.
Signed-off-by: Nick Dyer <[email protected]>
Tested-by: Andrew Duggan <[email protected]>
Tested-by: Chris Healy <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Acked-by: Dmitry Torokhov <[email protected]>
|
|
There are different datatypes available from a maXTouch chip. Add
support to retrieve reference data as well.
Signed-off-by: Nick Dyer <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Acked-by: Dmitry Torokhov <[email protected]>
|
|
The mXT1386 family of chips have a different architecture which splits
the diagnostic data into 3 columns.
Signed-off-by: Nick Dyer <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Acked-by: Dmitry Torokhov <[email protected]>
|
|
Invert the diagnostic data to match the orientation of the input device.
Signed-off-by: Nick Dyer <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Acked-by: Dmitry Torokhov <[email protected]>
|
|
The touchscreen may have a margin where not all the matrix is used. Read
the parameters from T9 and T100 and take account of the difference.
Note: this does not read the XORIGIN/YORIGIN fields so it assumes that
the touchscreen starts at (0,0)
Signed-off-by: Nick Dyer <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Acked-by: Dmitry Torokhov <[email protected]>
|
|
Register a video device to output T37 diagnostic data.
Signed-off-by: Nick Dyer <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Acked-by: Dmitry Torokhov <[email protected]>
|
|
Atmel maXTouch devices have a T37 object which can be used to read raw
touch deltas from the device. This consists of an array of 16-bit
integers, one for each node on the touchscreen matrix.
Signed-off-by: Nick Dyer <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Acked-by: Dmitry Torokhov <[email protected]>
|
|
Switch to using dev_dbg instead of naked printk so that output is uniform
with the other driver messages in the kernel.
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Switch the jornada720 keyboard driver to obtain its interrupt from the
platform device, rather than via a hard-coded interrupt number obtained
from the mach/irqs.h header.
Signed-off-by: Russell King <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Switch the jornada720_kbd driver to use the devm_* APIs. This is in
preparation to removing the mach/irqs.h include from this driver.
Signed-off-by: Russell King <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact. The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
This patch fix the following checkpatch report:
Blank lines aren't necessary after an open brace
Signed-off-by: LABBE Corentin <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Checkpatch complains about the text suggesting writing to
Free Software Foundation for GPLv2 license copy.
This patch remove that text.
Signed-off-by: LABBE Corentin <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The usage of of_device_get_match_data reduce the code size a bit.
Furthermore, it is better to use a standard function for
getting the match data.
Signed-off-by: LABBE Corentin <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The new(ish) ft6236 simply re-implements the M09 protocol of the
(much) older edt-ft5x06.c driver.
This commit removes this duplicate driver and adds the i2c ids and
dt compatible string to the edt-ft5x06.c driver to keep compatibility.
This commit also adds the standard touchscreen properties as optional
properties to the edt,ft5x06 binding, these were documented in the
focaltech,ft6236 bindingi, but were missing from the edt,ft5x06 doc.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
ADS7846 regulator is disabled twice in a row in ads7846_remove(). Valid
one is in ads7846_disable().
Removing the ads7846 module causes warning about unbalanced disables.
...
WARNING: CPU: 0 PID: 29269 at drivers/regulator/core.c:2251 _regulator_disable+0xf8/0x130
unbalanced disables for vads7846
CPU: 0 PID: 29269 Comm: rmmod Tainted: G D W 4.7.0+ #3
Hardware name: HTC Magician
...
show_stack+0x10/0x14
__warn+0xd8/0x100
warn_slowpath_fmt+0x38/0x48
_regulator_disable+0xf8/0x130
regulator_disable+0x34/0x60
ads7846_remove+0x58/0xd4 [ads7846]
spi_drv_remove+0x1c/0x34
__device_release_driver+0x84/0x114
driver_detach+0x8c/0x90
bus_remove_driver+0x5c/0xc8
SyS_delete_module+0x1a0/0x238
ret_fast_syscall+0x0/0x38
Signed-off-by: Petr Cvek <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The map_offset variable is specific to the register and needs to be reset
in the loop. Otherwise, subsequent register's subpacket maps will have
their bits set at the wrong index.
Signed-off-by: Andrew Duggan <[email protected]>
Tested-by: Nitin Chaudhary <[email protected]>
Reviewed-by: Benjamin Tissoires <[email protected]>
Cc: [email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Commit fe6b0dfaba68 ("Input: tegra-kbc - use reset framework")
accidentally converted _deassert to _assert, so there is no code
to wake up this hardware.
Fixes: fe6b0dfaba68 ("Input: tegra-kbc - use reset framework")
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Thierry Reding <[email protected]>
Acked-by: Laxman Dewangan <[email protected]>
Cc: [email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The silead code is using devm_foo for everything (and does not free
any resources). Except that it is using gpiod_get instead of
devm_gpiod_get (but is not freeing the gpio_desc), change this
to use devm_gpiod_get so that the gpio will be properly released.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The commit 4097461897df ("Input: i8042 - break load dependency ...")
correctly set up ps2_cmd_mutex pointer for the KBD port but forgot to do
the same for AUX port(s), which results in communication on KBD and AUX
ports to clash with each other.
Fixes: 4097461897df ("Input: i8042 - break load dependency ...")
Reported-by: Bruno Wolff III <[email protected]>
Tested-by: Bruno Wolff III <[email protected]>
Cc: [email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|