| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In some rare cases the 32 bit Rt value will overflow if z2 and x is max,
z1 is minimal value and x_plate_ohms is relatively high (for example 800
ohm). This would happen on some screen age with low pressure.
There are two possible fixes:
- make Rt 64bit
- reorder calculation to avoid overflow
The second variant seems to be preferable, since 64 bit calculation on
32 bit system is a bit more expensive.
Fixes: ffa458c1bd9b6f653008d450f337602f3d52a646 ("spi: ads7846 driver")
Co-developed-by: David Jander <[email protected]>
Signed-off-by: David Jander <[email protected]>
Signed-off-by: Oleksij Rempel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Starting with 3eac5c7e44f3 ("Input: ads7846 - extend the driver for ads7845
controller support"), the ads7845 was partially converted to full duplex
mode.
Since it is not touchscreen controller specific, it is better to extend
this conversion to cover entire driver. This will reduce CPU load and make
driver more readable.
Signed-off-by: Oleksij Rempel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
If touchscreen is released while busy reading HWMON device, the release
can be missed. The IRQ thread is not started because no touch is active
and BTN_TOUCH release event is never sent.
Fixes: f5a28a7d4858f94a ("Input: ads7846 - avoid pen up/down when reading hwmon")
Co-developed-by: Oleksij Rempel <[email protected]>
Signed-off-by: David Jander <[email protected]>
Signed-off-by: Oleksij Rempel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A fix for use-after-free in the Sun keyboard driver, a fix to firmware
updates on newer ICs in the Elan touchpad diver, and a couple misc
driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - fix firmware update on newer ICs
Input: resistive-adc-touch - fix kconfig dependency on IIO_BUFFER
Input: sunkbd - avoid use-after-free in teardown paths
Input: i8042 - allow insmod to succeed on devices without an i8042 controller
Input: adxl34x - clean up a data type in adxl34x_probe()
|
|
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/imx6ul_tsc.c: In function ‘adc_irq_fn’:
drivers/input/touchscreen/imx6ul_tsc.c:307:6: warning: variable ‘value’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <[email protected]>
Reviewed-by: Haibo Chen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/input/keyboard/samsung-keypad.c: In function ‘samsung_keypad_irq’:
drivers/input/keyboard/samsung-keypad.c:149:15: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Do not overwrite spi->mode flags set by spi framework, otherwise the
chip select polarity will get lost.
Signed-off-by: Oleksij Rempel <[email protected]>
Acked-by: Dmitry Torokhov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
The argument to iap page type command depends on the firmware page size.
Fixes: bfd9b92bc8f9 ("Input: elan_i2c - handle firmware updated on newer ICs")
Signed-off-by: Jingle Wu <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Hard-coding resolution for st1633 device was wrong. Some of LCDs like
YTS700TLBC-02-100C has assembled Sitronix st1633 touchcontroller too. But
the resolution is not 320x480 as was hard-coded.
Add new function which reads correct resolution directly from register.
Signed-off-by: Andrej Valek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
When TOUCHSCREEN_ADC is enabled and IIO_BUFFER is disabled, it results
in the following Kbuild warning:
WARNING: unmet direct dependencies detected for IIO_BUFFER_CB
Depends on [n]: IIO [=y] && IIO_BUFFER [=n]
Selected by [y]:
- TOUCHSCREEN_ADC [=y] && !UML && INPUT [=y] && INPUT_TOUCHSCREEN [=y] && IIO [=y]
The reason is that TOUCHSCREEN_ADC selects IIO_BUFFER_CB without depending
on or selecting IIO_BUFFER while IIO_BUFFER_CB depends on IIO_BUFFER. This
can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fixes: aa132ffb6b0a ("input: touchscreen: resistive-adc-touch: add generic resistive ADC touchscreen")
Signed-off-by: Necip Fazil Yildiran <[email protected]>
Acked-by: Jonathan Cameron <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Fixes the kerneldoc warnings from building the driver with W=1.
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
[dtor: folded together several Lee's patches; added more descriptions]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
references it
Fixes the following W=1 kernel build warning(s):
In file included from drivers/input/touchscreen/cyttsp_i2c_common.c:24:
drivers/input/touchscreen/cyttsp4_core.h:236:27: warning: ‘cyttsp4_tch_abs_string’ defined but not used [-Wunused-const-variable=]
236 | static const char const cyttsp4_tch_abs_string[] = {
| ^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/input/touchscreen/cyttsp4_i2c.c:17:
drivers/input/touchscreen/cyttsp4_core.h:236:27: warning: ‘cyttsp4_tch_abs_string’ defined but not used [-Wunused-const-variable=]
236 | static const char * const cyttsp4_tch_abs_string[] = {
| ^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/input/touchscreen/cyttsp4_spi.c:17:
drivers/input/touchscreen/cyttsp4_core.h:236:27: warning: ‘cyttsp4_tch_abs_string’ defined but not used [-Wunused-const-variable=]
236 | static const char * const cyttsp4_tch_abs_string[] = {
| ^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/resistive-adc-touch.c:34: warning: cannot understand function prototype: 'struct grts_state '
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The location of the minus sign and the error code are
linked together for better human view.
Signed-off-by: Zhang Qilong <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/input/mouse/cyapa_gen5.c:392: warning: Function parameter or member 'cyapa' not described in 'cyapa_i2c_pip_write'
drivers/input/mouse/cyapa_gen5.c:392: warning: Function parameter or member 'buf' not described in 'cyapa_i2c_pip_write'
drivers/input/mouse/cyapa_gen5.c:392: warning: Function parameter or member 'size' not described in 'cyapa_i2c_pip_write'
drivers/input/mouse/cyapa_gen5.c:444: warning: Function parameter or member 'cyapa' not described in 'cyapa_empty_pip_output_data'
drivers/input/mouse/cyapa_gen5.c:444: warning: Function parameter or member 'buf' not described in 'cyapa_empty_pip_output_data'
drivers/input/mouse/cyapa_gen5.c:444: warning: Function parameter or member 'len' not described in 'cyapa_empty_pip_output_data'
drivers/input/mouse/cyapa_gen5.c:444: warning: Function parameter or member 'func' not described in 'cyapa_empty_pip_output_data'
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/input/mouse/cyapa.c:130: warning: Function parameter or member 'reg' not described in 'cyapa_i2c_write'
drivers/input/mouse/cyapa.c:130: warning: Excess function parameter 'ret' description in 'cyapa_i2c_write'
Signed-off-by: Lee Jones <[email protected]>
Reviewed-by: Benson Leung <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/input/misc/ab8500-ponkey.c:32: warning: Function parameter or member 'idev' not described in 'ab8500_ponkey'
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/input/keyboard/cros_ec_keyb.c:72: warning: cannot understand function prototype: 'struct cros_ec_bs_map '
Signed-off-by: Lee Jones <[email protected]>
Reviewed-by: Benson Leung <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
[dtor: fixed up docbook comments for cros_ec_keyb structure as well]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/input/keyboard/gpio_keys.c:119: warning: Function parameter or member 'dev' not described in 'get_bm_events_by_type'
drivers/input/keyboard/gpio_keys.c:119: warning: Excess function parameter 'input' description in 'get_bm_events_by_type'
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/input/mouse/elantech.c:1837: warning: Function parameter or member 'psmouse' not described in 'elantech_setup_smbus'
drivers/input/mouse/elantech.c:1837: warning: Function parameter or member 'info' not described in 'elantech_setup_smbus'
drivers/input/mouse/elantech.c:1837: warning: Function parameter or member 'leave_breadcrumbs' not described in 'elantech_setup_smbus'
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'num_rows' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'num_cols' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'input' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'regmap' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'key_sense_irq' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'key_stuck_irq' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'keycodes' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'dev' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'keystate' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'stuckstate' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'ctrl_reg' not described in 'pmic8xxx_kp'
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/input/keyboard/nomadik-ske-keypad.c:71: warning: Function parameter or member 'pclk' not described in 'ske_keypad'
drivers/input/keyboard/nomadik-ske-keypad.c:71: warning: Function parameter or member 'ske_keypad_lock' not described in 'ske_keypad'
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'input_dev' not described in 'drv2667_data'
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'client' not described in 'drv2667_data'
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'regmap' not described in 'drv2667_data'
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'work' not described in 'drv2667_data'
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'regulator' not described in 'drv2667_data'
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'page' not described in 'drv2667_data'
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'magnitude' not described in 'drv2667_data'
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'frequency' not described in 'drv2667_data'
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/input/misc/drv2665.c:59: warning: Function parameter or member 'input_dev' not described in 'drv2665_data'
drivers/input/misc/drv2665.c:59: warning: Function parameter or member 'client' not described in 'drv2665_data'
drivers/input/misc/drv2665.c:59: warning: Function parameter or member 'regmap' not described in 'drv2665_data'
drivers/input/misc/drv2665.c:59: warning: Function parameter or member 'work' not described in 'drv2665_data'
drivers/input/misc/drv2665.c:59: warning: Function parameter or member 'regulator' not described in 'drv2665_data'
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'input_dev' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'client' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'regmap' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'work' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'enable_gpio' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'regulator' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'magnitude' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'mode' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'library' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'rated_voltage' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'overdrive_voltage' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:244: warning: Function parameter or member 'voltage' not described in 'drv260x_calculate_voltage'
Signed-off-by: Lee Jones <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
We need to make sure we cancel the reinit work before we tear down the
driver structures.
Reported-by: Bodong Zhao <[email protected]>
Tested-by: Bodong Zhao <[email protected]>
Cc: [email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Use kobj_to_dev() instead of container_of().
Signed-off-by: Wang Qing <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The eKTF2132 is a touchscreen controller found, for example, in the Kobo
Aura ebook reader. It is similar to the ektf2127, but it uses a different
packet type to report touch events.
Signed-off-by: Jonathan Neuschäfer <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The i8042 module exports several symbols which may be used by other
modules.
Before this commit it would refuse to load (when built as a module itself)
on systems without an i8042 controller.
This is a problem specifically for the asus-nb-wmi module. Many Asus
laptops support the Asus WMI interface. Some of them have an i8042
controller and need to use i8042_install_filter() to filter some kbd
events. Other models do not have an i8042 controller (e.g. they use an
USB attached kbd).
Before this commit the asus-nb-wmi driver could not be loaded on Asus
models without an i8042 controller, when the i8042 code was built as
a module (as Arch Linux does) because the module_init function of the
i8042 module would fail with -ENODEV and thus the i8042_install_filter
symbol could not be loaded.
This commit fixes this by exiting from module_init with a return code
of 0 if no controller is found. It also adds a i8042_present bool to
make the module_exit function a no-op in this case and also adds a
check for i8042_present to the exported i8042_command function.
The latter i8042_present check should not really be necessary because
when builtin that function can already be used on systems without
an i8042 controller, but better safe then sorry.
Reported-and-tested-by: Marius Iacob <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The "revid" is used to store negative error codes so it should be an int
type.
Fixes: e27c729219ad ("Input: add driver for ADXL345/346 Digital Accelerometers")
Signed-off-by: Dan Carpenter <[email protected]>
Acked-by: Michael Hennerich <[email protected]>
Link: https://lore.kernel.org/r/20201026072824.GA1620546@mwanda
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull more parisc updates from Helge Deller:
- During this merge window O_NONBLOCK was changed to become 000200000,
but we missed that the syscalls timerfd_create(), signalfd4(),
eventfd2(), pipe2(), inotify_init1() and userfaultfd() do a strict
bit-wise check of the flags parameter.
To provide backward compatibility with existing userspace we
introduce parisc specific wrappers for those syscalls which filter
out the old O_NONBLOCK value and replaces it with the new one.
- Prevent HIL bus driver to get stuck when keyboard or mouse isn't
attached
- Improve error return codes when setting rtc time
- Minor documentation fix in pata_ns87415.c
* 'parisc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
ata: pata_ns87415.c: Document support on parisc with superio chip
parisc: Add wrapper syscalls to fix O_NONBLOCK flag usage
hil/parisc: Disable HIL driver when it gets stuck
parisc: Improve error return codes when setting rtc time
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a new driver for ADC driven joysticks
- a new Zintix touchscreen driver
- enhancements to Intel SoC button array driver
- support for F3A "function" in Synaptics RMI4 driver
- assorted driver fixups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (29 commits)
Input: Add MAINTAINERS entry for SiS i2c touch input driver
Input: evdev - per-client waitgroups
Input: synaptics - enable InterTouch for ThinkPad T14 Gen 1
Input: synaptics - enable InterTouch for ThinkPad P1/X1E gen 2
Input: synaptics-rmi4 - support bootloader v8 in f34v7
Input: synaptics-rmi4 - add support for F3A
Input: synaptics-rmi4 - rename f30_data to gpio_data
Input: add zinitix touchscreen driver
dt-bindings: input/touchscreen: add bindings for zinitix
Input: joystick - add ADC attached joystick driver.
dt-bindings: input: Add docs for ADC driven joystick
Input: sun4i-ps2 - fix handling of platform_get_irq() error
Input: twl4030_keypad - fix handling of platform_get_irq() error
Input: omap4-keypad - fix handling of platform_get_irq() error
Input: ep93xx_keypad - fix handling of platform_get_irq() error
Input: stmfts - fix a & vs && typo
Input: imx6ul_tsc - unify open/close and PM paths
Input: imx6ul_tsc - clean up some errors in imx6ul_tsc_resume()
Input: elants_i2c - fix typo for an attribute to show calibration count
Input: elants_i2c - report resolution of ABS_MT_TOUCH_MAJOR by FW information.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"cros-ec:
- Error code cleanup across cros-ec by Guenter
- Remove cros_ec_cmd_xfer in favor of cros_ec_cmd_xfer_status
cros_ec_typec:
- Landed initial USB4 support in typec connector class driver for
cros_ec
- Role switch bugfix on disconnect, and reordering configuration
steps
cros_ec_lightbar:
- Fix buffer outsize and result for get_lightbar_version
misc:
- Remove config MFD_CROS_EC, now that transition from MFD is complete
- Enable KEY_LEFTMETA in new location on arm based cros-ec-keyboard
keymap"
* tag 'tag-chrome-platform-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
ARM: dts: cros-ec-keyboard: Add alternate keymap for KEY_LEFTMETA
platform/chrome: Use kobj_to_dev() instead of container_of()
platform/chrome: cros_ec_proto: Drop cros_ec_cmd_xfer()
platform/chrome: cros_ec_proto: Update cros_ec_cmd_xfer() call-sites
platform/chrome: Kconfig: Remove the transitional MFD_CROS_EC config
platform/chrome: cros_ec_lightbar: Reduce ligthbar get version command
platform/chrome: cros_ec_trace: Add fields to command traces
platform/chrome: cros_ec_typec: Re-order connector configuration steps
platform/chrome: cros_ec_typec: Avoid setting usb role twice during disconnect
platform/chrome: cros_ec_typec: Send enum values to usb_role_switch_set_role()
platform/chrome: cros_ec_typec: USB4 support
pwm: cros-ec: Simplify EC error handling
platform/chrome: cros_ec_proto: Convert EC error codes to Linux error codes
platform/input: cros_ec: Replace -ENOTSUPP with -ENOPROTOOPT
pwm: cros-ec: Accept more error codes from cros_ec_cmd_xfer_status
platform/chrome: cros_ec_sysfs: Report range of error codes from EC
cros_ec_lightbar: Accept more error codes from cros_ec_cmd_xfer_status
iio: cros_ec: Accept -EOPNOTSUPP as 'not supported' error code
|
|
When starting a HP machine with HIL driver but without an HIL keyboard
or HIL mouse attached, it may happen that data written to the HIL loop
gets stuck (e.g. because the transaction queue is full). Usually one
will then have to reboot the machine because all you see is and endless
output of:
Transaction add failed: transaction already queued?
In the higher layers hp_sdc_enqueue_transaction() is called to queued up
a HIL packet. This function returns an error code, and this patch adds
the necessary checks for this return code and disables the HIL driver if
further packets can't be sent.
Tested on a HP 730 and a HP 715/64 machine.
Signed-off-by: Helge Deller <[email protected]>
Cc: <[email protected]>
|
|
Prepare input updates for 5.10 merge window.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V updates from Wei Liu:
- a series from Boqun Feng to support page size larger than 4K
- a few miscellaneous clean-ups
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hv: clocksource: Add notrace attribute to read_hv_sched_clock_*() functions
x86/hyperv: Remove aliases with X64 in their name
PCI: hv: Document missing hv_pci_protocol_negotiation() parameter
scsi: storvsc: Support PAGE_SIZE larger than 4K
Driver: hv: util: Use VMBUS_RING_SIZE() for ringbuffer sizes
HID: hyperv: Use VMBUS_RING_SIZE() for ringbuffer sizes
Input: hyperv-keyboard: Use VMBUS_RING_SIZE() for ringbuffer sizes
hv_netvsc: Use HV_HYP_PAGE_SIZE for Hyper-V communication
hv: hyperv.h: Introduce some hvpfn helper functions
Drivers: hv: vmbus: Move virt_to_hvpfn() to hyperv header
Drivers: hv: Use HV_HYP_PAGE in hv_synic_enable_regs()
Drivers: hv: vmbus: Introduce types of GPADL
Drivers: hv: vmbus: Move __vmbus_open()
Drivers: hv: vmbus: Always use HV_HYP_PAGE_SIZE for gpadl
drivers: hv: remove cast from hyperv_die_event
|
|
All evdev clients share a common waitgroup. On new input events, all
clients waiting on this waitgroup are woken up, even those filtering out
the events, possibly more than once per event. This leads to duplicated
and unwanted wakeups.
Split the shared waitgroup into per-client waitgroups for more
fine-grained wakeups.
Signed-off-by: Kenny Levinsen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
With the new RMI4 F3A support, we're now able to enable full RMI4
support for this model.
Signed-off-by: Hans de Goede <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
With the new RMI4 F3A support, we're now able to enable full RMI4
support for this model. We also tidy up the comments a bit, as the X1E
is essentially the same computer as the P1.
Acked-by: Lyude Paul <[email protected]>
Signed-off-by: Jason A. Donenfeld <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
With the recent addition of the F3A support, we can now accept
bootloader v8, which will help support recent Thinkpads.
Acked-by: Lyude Paul <[email protected]>
Signed-off-by: Jason A. Donenfeld <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
RMI4 F3A supports the touchpad GPIO function, it's designed to
support more GPIOs and used on newer touchpads. This patch adds
support of the touchpad buttons.
Signed-off-by: Vincent Huang <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Tested-by: Hans de Goede <[email protected]>
Reviewed-by: Andrew Duggan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
f30_data in rmi_device_platform_data could be also referenced by RMI
function 3A, so rename it and the structure name to avoid confusion.
Signed-off-by: Vincent Huang <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Tested-by: Hans de Goede <[email protected]>
Reviewed-by: Andrew Duggan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Add support for the bt541 touchscreen IC from zinitix, loosely based on
downstream driver. The driver currently supports multitouch (5 touch points).
The bt541 seems to support touch keys, but the support was not added because
that functionality is not being utilized by the touchscreen used for testing.
Based on the similartities between downstream drivers, it seems likely that
other similar touchscreen ICs can be supported with this driver in the future.
Signed-off-by: Michael Srba <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A couple more driver quirks, now enabling newer trackpoints from
Synaptics for real"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add nopnp quirk for Acer Aspire 5 A515
Input: trackpoint - enable Synaptics trackpoints
|
|
Add a driver for joystick devices connected to ADC controllers
supporting the Industrial I/O subsystem.
Signed-off-by: Artur Rojek <[email protected]>
Tested-by: Paul Cercueil <[email protected]>
Tested-by: Heiko Stuebner <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Touchpad on this laptop is not detected properly during boot, as PNP
enumerates (wrongly) AUX port as disabled on this machine.
Fix that by adding this board (with admittedly quite funny DMI
identifiers) to nopnp quirk list.
Reported-by: Andrés Barrantes Silman <[email protected]>
Signed-off-by: Jiri Kosina <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Cc: [email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Add Synaptics IDs in trackpoint_start_protocol() to mark them as valid.
Signed-off-by: Vincent Huang <[email protected]>
Fixes: 6c77545af100 ("Input: trackpoint - add new trackpoint variant IDs")
Reviewed-by: Harry Cutts <[email protected]>
Tested-by: Harry Cutts <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
For a Hyper-V vmbus, the size of the ringbuffer has two requirements:
1) it has to take one PAGE_SIZE for the header
2) it has to be PAGE_SIZE aligned so that double-mapping can work
VMBUS_RING_SIZE() could calculate a correct ringbuffer size which
fulfills both requirements, therefore use it to make sure vmbus work
when PAGE_SIZE != HV_HYP_PAGE_SIZE (4K).
Note that since the argument for VMBUS_RING_SIZE() is the size of
payload (data part), so it will be minus 4k (the size of header when
PAGE_SIZE = 4k) than the original value to keep the ringbuffer total
size unchanged when PAGE_SIZE = 4k.
Signed-off-by: Boqun Feng <[email protected]>
Cc: Michael Kelley <[email protected]>
Cc: Dmitry Torokhov <[email protected]>
Acked-by: Dmitry Torokhov <[email protected]>
Reviewed-by: Michael Kelley <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Wei Liu <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just a couple of driver quirks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: trackpoint - add new trackpoint variant IDs
Input: i8042 - add Entroware Proteus EL07R4 to nomux and reset lists
|