| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
During a hotplug cycle (such as a TV going out of suspend, or when the
cable is disconnected and reconnected), the expectation is that the same
state used before the disconnection is reused until the next commit.
However, the HDMI scrambling requires that some flags are set in the
monitor, and those flags are very likely to be reset when the cable has
been disconnected. This will thus result in a blank display, even if the
display pipeline configuration hasn't been modified or is in the exact
same state.
The solution we've had so far is to enable the scrambling-related bits
again on reconnection, but the HDMI 2.0 specification (Section 6.1.3.1 -
Scrambling Control) requires that the scrambling enable bit is set
before sending any scrambled video signal. Using that solution thus
breaks that expectation.
The solution used by i915 is to do a full modeset on the connector so
that we disable the video signal, enable the scrambling bit, and enable
the video signal again.
As such, we took that code and plugged it into vc4. It probably could
have been turned into an helper, but it proved to be difficult for
several reasons:
* i915 has fairly different structures than simpler KMS drivers such
as vc4, so doing some code that works with both proved to be
difficult;
* Other simpler drivers could reuse some of it (tegra, dw-hdmi), but
it would still require to move some parameters currently stored in
private structure that are needed to compute whether the scrambling
is needed or not, and then inform the driver that it needs to be
enabled. Some of those parameters are already in core structures
(drm_display_mode, drm_display_info, bpc), but the output format
isnt't. Adding it is fairly challenging since unlike the TMDS char
rate or mode, there's no consensus on what format to pick in
drivers, so it's not possible to write some generic code that can
depend on it.
For these reasons, we chose to duplicate the code for now, until someone
else really needs it as well, in which case we will be able to convert
it into a generic helper.
Reviewed-by: Ville Syrjälä <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
We'll need it earlier in the driver, so let's move it next to the other
scrambling-related helpers.
Reviewed-by: Ville Syrjälä <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
We'll need the locking context in future patch, so let's convert .detect
to .detect_ctx.
Reviewed-by: Ville Syrjälä <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Our detect callback has a bunch of operations to perform depending on
the current and last status of the connector, such a setting the CEC
physical address or enabling the scrambling again.
This is currently dealt with a bunch of if / else statetements that make
it fairly difficult to read and extend.
Let's move all that logic to a function of its own.
Reviewed-by: Ville Syrjälä <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
We recently introduced a new mutex to protect concurrent execution of
ALSA and KMS hooks, and the concurrent access to some of vc4_hdmi
fields.
However, using it in the detect hook was creating a reentrency issue
with CEC code. Indeed, calling cec_s_phys_addr_from_edid from detect
might call the CEC adap_enable hook with the lock held, eventually
resulting in a deadlock.
Since we didn't really need to protect anything at the moment in the CEC
code, the decision was made to ignore the mutex in those CEC hooks,
working around the issue.
However, we can have the same thing happening if we end up triggering a
mode set from the detect callback, for example using
drm_atomic_helper_connector_hdmi_reset_link().
Since we don't really need to protect anything in detect either, let's
just drop the lock in detect, and add it again in CEC.
Reviewed-by: Ville Syrjälä <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Even though vc4_hdmi_supports_scrambling takes a mode as an argument, it
never uses it. Let's remove it.
Reviewed-by: Ville Syrjälä <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
We don't modify the drm_display_mode pointer we have in the driver in
most places, so let's make them const.
Reviewed-by: Ville Syrjälä <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.1-rc1:
[airlied - fix sun4i_tv build]
UAPI Changes:
- Hide unregistered connectors from GETCONNECTOR ioctl.
- drm/virtio no longer advertises LINEAR modifier, as it doesn't work.
-
Cross-subsystem Changes:
- Fix GPF in udmabuf failure path.
Core Changes:
- Rework TTM placement to use intersect/compatible functions.
- Drop legacy DP-MST support.
- More DP-MST related fixes, and move all state into atomic.
- Make DRM_MIPI_DBI select DRM_KMS_HELPER.
- Add audio_infoframe packing for DP.
- Add logging when some atomic check functions fail.
- Assorted documentation updates and fixes.
Driver Changes:
- Assorted cleanups and fixes in msm, lcdif, nouveau, virtio,
panel/ilitek, bridge/icn6211, tve200, gma500, bridge/*, panfrost, via,
bochs, qxl, sun4i.
- Add add AUO B133UAN02.1, IVO M133NW4J-R3, Innolux N120ACA-EA1 eDP panels.
- Improve DP-MST modeset state handling in amdgpu, nouveau, i915.
- Drop DP-MST from radeon driver, it was broken and only user of legacy
DP-MST.
- Handle unplugging better in vc4.
- Simplify drm cmdparser tests.
- Add DP support to ti-sn65dsi86.
- Add MT8195 DP support to mediatek.
- Support RGB565, XRGB64, and ARGB64 formats in vkms.
- Convert sun4i tv support to atomic.
- Refactor vc4/vec TV Modesetting, and fix timings.
- Use atomic helpers instead of simple display helpers in ssd130x.
Maintainer changes:
- Add Douglas Anderson as reviewer for panel-edp.
Signed-off-by: Dave Airlie <[email protected]>
From: Maarten Lankhorst <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
This commit fixes vertical timings of the VEC (composite output) modes
to accurately represent the 525-line ("NTSC") and 625-line ("PAL") ITU-R
standards.
Previous timings were actually defined as 502 and 601 lines, resulting
in non-standard 62.69 Hz and 52 Hz signals being generated,
respectively.
Signed-off-by: Mateusz Kwiatkowski <[email protected]>
Acked-by: Noralf Trønnes <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Let's remove the superfluous tv_mode field, which was redundant with the
mode field in struct drm_tv_connector_state.
Signed-off-by: Mateusz Kwiatkowski <[email protected]>
Reviewed-by: Noralf Trønnes <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Change the mode_set function pointer logic to declarative config0,
config1 and custom_freq fields, to make TV mode setting logic more
concise and uniform.
Signed-off-by: Mateusz Kwiatkowski <[email protected]>
Reviewed-by: Noralf Trønnes <[email protected]>
[Maxime: Fixed != 0 check, added tv_mode variable]
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The VC4 VEC driver still uses legacy enable and disable hook
implementation. Let's convert to the atomic variants.
Reviewed-by: Noralf Trønnes <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The mode_fixup hooks are deprecated, and the behaviour we implement is the
default one anyway. Let's remove it.
Reviewed-by: Noralf Trønnes <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.1:
UAPI Changes:
Cross-subsystem Changes:
- DMA-buf: documentation updates.
- Assorted small fixes to vga16fb
- Fix fbdev drivers to use the aperture helpers.
- Make removal of conflicting drivers work correctly without fbdev enabled.
Core Changes:
- bridge, scheduler, dp-mst: Assorted small fixes.
- Add more format helpers to fourcc, and use it to replace the cpp usage.
- Add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx (single channel), and DRM_FORMAT_Dxx
("darkness", inverted single channel)
- Add packed AYUV8888 and XYUV8888 formats.
- Assorted documentation updates.
- Rename ttm_bo_init to ttm_bo_init_validate.
- Allow TTM bo's to exist without backing store.
- Convert drm selftests to kunit.
- Add managed init functions for (panel) bridge, crtc, encoder and connector.
- Fix endianness handling in various format conversion helpers.
- Make tests pass on big-endian platforms, and add test for rgb888 -> rgb565
- Move DRM_PLANE_HELPER_NO_SCALING to atomic helpers and rename, so
drm_plane_helper is no longer needed in most drivers.
- Use idr_init_base instead of idr_init.
- Rename FB and GEM CMA helpers to DMA helpers.
- Rework XRGB8888 related conversion helpers, and add drm_fb_blit() that
takes a iosys_map. Make drm_fb_memcpy take an iosys_map too.
- Move edid luminance calculation to core, and use it in i915.
Driver Changes:
- bridge/{adv7511,ti-sn65dsi86,parade-ps8640}, panel/{simple,nt35510,tc358767},
nouveau, sun4i, mipi-dsi, mgag200, bochs, arm, komeda, vmwgfx, pl111:
Assorted small fixes and doc updates.
- vc4: Rework hdmi power up, and depend on PM.
- panel/simple: Add Samsung LTL101AL01.
- ingenic: Add JZ4760(B) support, avoid a modeset when sharpness property
is unchanged, and use the new PM ops.
- Revert some amdgpu commits that cause garbaged graphics when starting
X, and reapply them with the real problem fixed.
- Completely rework vc4 init to use managed helpers.
- Rename via_drv to via_dri1, and move all stuff there only used by the
dri1 implementation in preperation for atomic modeset.
- Use regmap bulk write in ssd130x.
- Power sequence and clock updates to it6505.
- Split panel-sitrox-st7701 init sequence and rework mode programming code.
- virtio: Improve error and edge conditions handling, and convert to use managed
helpers.
- Add Samsung LTL101AL01, B120XAN01.0, R140NWF5 RH, DMT028VGHMCMI-1A T, panels.
- Add generic fbdev support to komeda.
- Split mgag200 modeset handling to make it more model-specific.
- Convert simpledrm to use atomic helpers.
- Improve udl suspend/disconnect handling.
Signed-off-by: Daniel Vetter <[email protected]>
From: Maarten Lankhorst <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
In vc4_hvs_dump_state() potentially freed resources are protected from
being accessed with drm_dev_enter()/drm_dev_exit().
Also include drm_print_regset32() in the protected section, since
drm_print_regset32() does access memory that is typically mapped via
devm_* calls.
Fixes: 969cfae1f01d ("drm/vc4: hvs: Protect device resources after removal")
Signed-off-by: Danilo Krummrich <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
(Hardware) resources which are bound to the driver and device lifecycle
must not be accessed after the device and driver are unbound.
However, the DRM device isn't freed as long as the last user closed it,
hence userspace can still call into the driver.
Therefore protect the critical sections which are accessing those
resources with drm_dev_enter() and drm_dev_exit().
Fixes: 7cc4214c27cf ("drm/vc4: crtc: Switch to drmm_kzalloc")
Signed-off-by: Danilo Krummrich <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
(Hardware) resources which are bound to the driver and device lifecycle
must not be accessed after the device and driver are unbound.
However, the DRM device isn't freed as long as the last user closed it,
hence userspace can still call into the driver.
Therefore protect the critical sections which are accessing those
resources with drm_dev_enter() and drm_dev_exit().
Fixes: 9872c7a31921 ("drm/vc4: plane: Switch to drmm_universal_plane_alloc()")
Signed-off-by: Danilo Krummrich <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
In vc4_hdmi_encoder_{pre,post}_crtc_enable() commit cd00ed5187bf
("drm/vc4: hdmi: Protect device resources after removal") missed to
unlock the mutex before returning due to drm_dev_enter() indicating the
device being unplugged.
Fixes: cd00ed5187bf ("drm/vc4: hdmi: Protect device resources after removal")
Signed-off-by: Danilo Krummrich <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The current code tries to handle the case where CONFIG_PM isn't selected
by first calling our runtime_resume implementation and then properly
report the power state to the runtime_pm core.
This allows to have a functionning device even if pm_runtime_get_*
functions are nops.
However, the device power state if CONFIG_PM is enabled is
RPM_SUSPENDED, and thus our vc4_hdmi_write() and vc4_hdmi_read() calls
in the runtime_pm hooks will now report a warning since the device might
not be properly powered.
Even more so, we need CONFIG_PM enabled since the previous RaspberryPi
have a power domain that needs to be powered up for the HDMI controller
to be usable.
The previous patch has created a dependency on CONFIG_PM, now we can
just assume it's there and only call pm_runtime_resume_and_get() to make
sure our device is powered in bind.
Link: https://lore.kernel.org/r/[email protected]
Acked-by: Thomas Zimmermann <[email protected]>
Tested-by: Stefan Wahren <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
(cherry picked from commit 53565c28e6af2cef6bbf438c34250135e3564459)
Signed-off-by: Maxime Ripard <[email protected]>
|
|
We already depend on runtime PM to get the power domains and clocks for
most of the devices supported by the vc4 driver, so let's just select it
to make sure it's there.
Link: https://lore.kernel.org/r/[email protected]
Acked-by: Thomas Zimmermann <[email protected]>
Tested-by: Stefan Wahren <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
(cherry picked from commit f1bc386b319e93e56453ae27e9e83817bb1f6f95)
Signed-off-by: Maxime Ripard <[email protected]>
|
|
This driver includes the deprecated OF GPIO header <linux/of_gpio.h>
yet fail to use symbols from it, so drop the include.
Cc: Emma Anholt <[email protected]>
Cc: Maxime Ripard <[email protected]>
Signed-off-by: Maíra Canal <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"As the diffstat shows, we've had lots of developments in a wide range
at this time; the majority of changes are about ASoC, including
subsystem-wide cleanups, continued SOF / Intel updates and a bunch of
new drivers (as usual), while there have been some significant (but
almost invisible) improvements in ALSA core side, too.
Below are some highlights:
Core:
- Faster lookups of control elements with Xarray; normal user won't
notice, but on the devices with tons of control elements, it can be
visibly faster
- Support for input validation for controls; this will harden for
badly written drivers in general with a slight overhead
- Deferred async signal handling for working around the potential
deadlocks
- Cleanup / refactoring raw MIDI locking code
ASoC:
- Restructing of the set_fmt() callbacks for making things clearer in
situations like CODEC to CODEC links
- Clean up and modernizing the DAI naming scheme setups
- Merge of more of the Intel AVS driver stack, including some board
integrations
- New version 4 mechanism for communication with SOF DSPs
- Suppoort for dynamically selecting the PLL to use at runtime on
i.MX platforms
- Improvements for CODEC to CODEC support in the generic cards
- Support for AMD Jadeite and various machines, AMD RPL, Intel
MetorLake DSPs, Mediatek MT8186 DSPs and MT6366, nVidia Tegra
MDDRC, OPE and PEQ, NXP TFA9890, Qualcomm SDM845, WCD9335 and
WAS883x, and Texas Instruments TAS2780
HD- and USB-audio:
- Continued improvement for CS35L41 (sub)codec support
- More quirks for various devices (HP, Lenovo, Dell, Clevo)"
* tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (778 commits)
ALSA: hda/realtek: Add quirk for HP Spectre x360 15-eb0xxx
ALSA: line6: Replace sprintf() with sysfs_emit()
ALSA: hda: Replace sprintf() with sysfs_emit()
ALSA: pcm: Replace sprintf() with sysfs_emit()
ALSA: core: Replace scnprintf() with sysfs_emit()
ALSA: control-led: Replace sprintf() with sysfs_emit()
ALSA: aoa: Replace sprintf() with sysfs_emit()
ALSA: ac97: Replace sprintf() with sysfs_emit()
ALSA: hda/realtek: Add quirk for Clevo NV45PZ
ALSA: hda/realtek: Add quirk for Lenovo Yoga9 14IAP7
ALSA: control: Use deferred fasync helper
ALSA: pcm: Use deferred fasync helper
ALSA: timer: Use deferred fasync helper
ALSA: core: Add async signal helpers
ASoC: q6asm: use kcalloc() instead of kzalloc()
ACPI: scan: Add CLSA0101 Laptop Support
ALSA: hda: cs35l41: Support CLSA0101
ALSA: hda: cs35l41: Use the CS35L41 HDA internal define
ASoC: dt-bindings: use spi-peripheral-props.yaml
ASoC: codecs: va-macro: use fsgen as clock
...
|
|
The field paddr of struct drm_gem_dma_object holds a DMA address, which
might actually be a physical address. However, depending on the platform,
it can also be a bus address or a virtual address managed by an IOMMU.
Hence, rename the field to dma_addr, which is more applicable.
In order to do this renaming the following coccinelle script was used:
```
@@
struct drm_gem_dma_object *gem;
@@
- gem->paddr
+ gem->dma_addr
@@
struct drm_gem_dma_object gem;
@@
- gem.paddr
+ gem.dma_addr
@exists@
typedef dma_addr_t;
symbol paddr;
@@
dma_addr_t paddr;
<...
- paddr
+ dma_addr
...>
@@
symbol paddr;
@@
dma_addr_t
- paddr
+ dma_addr
;
```
This patch is compile-time tested with:
```
make ARCH={x86_64,arm,arm64} allyesconfig
make ARCH={x86_64,arm,arm64} drivers/gpu/drm`
```
Acked-by: Sam Ravnborg <[email protected]>
Suggested-by: Laurent Pinchart <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Signed-off-by: Danilo Krummrich <[email protected]>
Signed-off-by: Sam Ravnborg <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Rename "GEM CMA" helpers to "GEM DMA" helpers - considering the
hierarchy of APIs (mm/cma -> dma -> gem dma) calling them "GEM
DMA" seems to be more applicable.
Besides that, commit e57924d4ae80 ("drm/doc: Task to rename CMA helpers")
requests to rename the CMA helpers and implies that people seem to be
confused about the naming.
In order to do this renaming the following script was used:
```
#!/bin/bash
DIRS="drivers/gpu include/drm Documentation/gpu"
REGEX_SYM_UPPER="[0-9A-Z_\-]"
REGEX_SYM_LOWER="[0-9a-z_\-]"
REGEX_GREP_UPPER="(${REGEX_SYM_UPPER}*)(GEM)_CMA_(${REGEX_SYM_UPPER}*)"
REGEX_GREP_LOWER="(${REGEX_SYM_LOWER}*)(gem)_cma_(${REGEX_SYM_LOWER}*)"
REGEX_SED_UPPER="s/${REGEX_GREP_UPPER}/\1\2_DMA_\3/g"
REGEX_SED_LOWER="s/${REGEX_GREP_LOWER}/\1\2_dma_\3/g"
# Find all upper case 'CMA' symbols and replace them with 'DMA'.
for ff in $(grep -REHl "${REGEX_GREP_UPPER}" $DIRS)
do
sed -i -E "$REGEX_SED_UPPER" $ff
done
# Find all lower case 'cma' symbols and replace them with 'dma'.
for ff in $(grep -REHl "${REGEX_GREP_LOWER}" $DIRS)
do
sed -i -E "$REGEX_SED_LOWER" $ff
done
# Replace all occurrences of 'CMA' / 'cma' in comments and
# documentation files with 'DMA' / 'dma'.
for ff in $(grep -RiHl " cma " $DIRS)
do
sed -i -E "s/ cma / dma /g" $ff
sed -i -E "s/ CMA / DMA /g" $ff
done
# Rename all 'cma_obj's to 'dma_obj'.
for ff in $(grep -RiHl "cma_obj" $DIRS)
do
sed -i -E "s/cma_obj/dma_obj/g" $ff
done
```
Only a few more manual modifications were needed, e.g. reverting the
following modifications in some DRM Kconfig files
- select CMA if HAVE_DMA_CONTIGUOUS
+ select DMA if HAVE_DMA_CONTIGUOUS
as well as manually picking the occurrences of 'CMA'/'cma' in comments and
documentation which relate to "GEM CMA", but not "FB CMA".
Also drivers/gpu/drm/Makefile was fixed up manually after renaming
drm_gem_cma_helper.c to drm_gem_dma_helper.c.
This patch is compile-time tested building a x86_64 kernel with
`make allyesconfig && make drivers/gpu/drm`.
Acked-by: Sam Ravnborg <[email protected]>
Acked-by: Thomas Zimmermann <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Signed-off-by: Danilo Krummrich <[email protected]>
Reviewed-by: Liviu Dudau <[email protected]> #drivers/gpu/drm/arm
Signed-off-by: Sam Ravnborg <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Rename "FB CMA" helpers to "FB DMA" helpers - considering the hierarchy
of APIs (mm/cma -> dma -> fb dma) calling them "FB DMA" seems to be
more applicable.
Besides that, commit e57924d4ae80 ("drm/doc: Task to rename CMA helpers")
requests to rename the CMA helpers and implies that people seem to be
confused about the naming.
In order to do this renaming the following script was used:
```
#!/bin/bash
DIRS="drivers/gpu include/drm Documentation/gpu"
REGEX_SYM_UPPER="[0-9A-Z_\-]"
REGEX_SYM_LOWER="[0-9a-z_\-]"
REGEX_GREP_UPPER="(${REGEX_SYM_UPPER}*)(FB)_CMA_(${REGEX_SYM_UPPER}*)"
REGEX_GREP_LOWER="(${REGEX_SYM_LOWER}*)(fb)_cma_(${REGEX_SYM_LOWER}*)"
REGEX_SED_UPPER="s/${REGEX_GREP_UPPER}/\1\2_DMA_\3/g"
REGEX_SED_LOWER="s/${REGEX_GREP_LOWER}/\1\2_dma_\3/g"
# Find all upper case 'CMA' symbols and replace them with 'DMA'.
for ff in $(grep -REHl "${REGEX_GREP_UPPER}" $DIRS)
do
sed -i -E "$REGEX_SED_UPPER" $ff
done
# Find all lower case 'cma' symbols and replace them with 'dma'.
for ff in $(grep -REHl "${REGEX_GREP_LOWER}" $DIRS)
do
sed -i -E "$REGEX_SED_LOWER" $ff
done
# Replace all occurrences of 'CMA' / 'cma' in comments and
# documentation files with 'DMA' / 'dma'.
for ff in $(grep -RiHl " cma " $DIRS)
do
sed -i -E "s/ cma / dma /g" $ff
sed -i -E "s/ CMA / DMA /g" $ff
done
```
Only a few more manual modifications were needed, e.g. reverting the
following modifications in some DRM Kconfig files
- select CMA if HAVE_DMA_CONTIGUOUS
+ select DMA if HAVE_DMA_CONTIGUOUS
as well as manually picking the occurrences of 'CMA'/'cma' in comments and
documentation which relate to "FB CMA", but not "GEM CMA".
This patch is compile-time tested building a x86_64 kernel with
`make allyesconfig && make drivers/gpu/drm`.
Acked-by: Sam Ravnborg <[email protected]>
Acked-by: Thomas Zimmermann <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Signed-off-by: Danilo Krummrich <[email protected]>
Reviewed-by: Liviu Dudau <[email protected]> #drivers/gpu/drm/arm
Signed-off-by: Sam Ravnborg <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Quite a lot of drivers include the drm_fb_cma_helper.h header file
without actually making use of it's provided API, hence remove those
includes.
Suggested-by: Sam Ravnborg <[email protected]>
Signed-off-by: Danilo Krummrich <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Acked-by: Sam Ravnborg <[email protected]>
Signed-off-by: Sam Ravnborg <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Remove the include statement for drm_plane_helper.h from all the files
that don't need it. Althogh the header file is almost empty, many drivers
include it somewhere.
Signed-off-by: Thomas Zimmermann <[email protected]>
Reviewed-by: Sam Ravnborg <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
devm_pm_runtime_enable() simplifies the driver a bit since it will call
pm_runtime_disable() automatically through a device-managed action.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
At bind time, vc4_v3d_bind() will read a register to retrieve the v3d
version and make sure it's a version we're compatible with.
However, the v3d has an optional clock that is enabled only after the
register read-out and a power domain that wasn't enabled at all in the bind
implementation. This was working fine at boot because both were enabled,
but resulted in the version check failing if we were unbinding and
rebinding the driver because the unbinding would have turned them off.
The fix isn't as easy as calling pm_runtime_resume_and_get() prior to the
register access to power up the power domain though.
Indeed, the runtime_resume implementation will enable the clock mentioned
above, call vc4_v3d_init_hw() and then vc4_irq_enable().
Prior to the previous patch, vc4_irq_enable() needed to occur after our
call to platform_get_irq() and vc4_irq_install(), since vc4_irq_enable()
used to call enable_irq() and vc4_irq_install() will call request_irq().
vc4_irq_install() will also do some register access, so needs the power
domain to be on. So we ended up in a situation where
vc4_v3d_runtime_resume() needed vc4_irq_install() to have been called
before, and vc4_irq_install() needed vc4_v3d_runtime_resume().
The previous patch removed the enable_irq() call in vc4_irq_enable() and
thus removed the dependency of vc4_v3d_runtime_resume() on
vc4_irq_install().
Thus, we can now rework our bind implementation to call
pm_runtime_resume_and_get() before our register access to make sure the
power domain is on. vc4_v3d_runtime_resume() also takes care of turning the
clock on and calling vc4_v3d_init_hw() so we can remove them from bind.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The vc4_irq_disable(), among other things, will call disable_irq() to
complete any in-flight interrupts.
This requires its counterpart, vc4_irq_enable(), to call enable_irq() which
causes issues addressed in a later patch.
However, vc4_irq_disable() is called by two callees: vc4_irq_uninstall()
and vc4_v3d_runtime_suspend().
vc4_irq_uninstall() also calls free_irq() which already disables the
interrupt line. We thus don't require an explicit disable_irq() for that
call site.
vc4_v3d_runtime_suspend() doesn't have any other code. However, the rest of
vc4_irq_disable() masks the interrupts coming from the v3d, so explictly
disabling the interrupt line is also redundant.
The only thing we really care about is thus to make sure we don't have any
handler in-flight, as suggested by the comment. We can thus replace
disable_irq() by synchronize_irq().
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
vc4_perfmon_open_file() will instantiate a mutex for that file instance,
but we never call mutex_destroy () in vc4_perfmon_close_file().
Let's add that missing call.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
mutex_init is supposed to be balanced by a call to mutex_destroy that we
were never doing in the vc4 driver.
Since a DRM-managed mutex_init variant has been introduced, let's just
switch to it.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The vc4 has a custom API to allow components to register a debugfs file
before the DRM driver has been registered and the debugfs_init hook has
been called.
However, the .late_register hook allows to have the debugfs file creation
deferred after that time already.
Let's remove our custom code to only register later our debugfs entries as
part of either debugfs_init or after it.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
vc4_debugfs_add_file() can fail, so let's propagate its error code instead
of silencing it.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Our current code now mixes some resources whose lifetime are tied to the
device (clocks, IO mappings, etc.) and some that are tied to the DRM device
(encoder, bridge).
The device one will be freed at unbind time, but the DRM one will only be
freed when the last user of the DRM device closes its file handle.
So we end up with a time window during which we can call the encoder hooks,
but we don't have access to the underlying resources and device.
Let's protect all those sections with drm_dev_enter() and drm_dev_exit() so
that we bail out if we are during that window.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
devm_pm_runtime_enable() simplifies the driver a bit since it will call
pm_runtime_disable() automatically through a device-managed action.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Whenever the device and driver are unbound, the main device and all the
subdevices will be removed by calling their unbind() method.
However, the DRM device itself will only be freed when the last user will
have closed it.
It means that there is a time window where the device and its resources
aren't there anymore, but the userspace can still call into our driver.
Fortunately, the DRM framework provides the drm_dev_enter() and
drm_dev_exit() functions to make sure our underlying device is still there
for the section protected by those calls. Let's add them to the VEC driver.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The current code will call drm_connector_unregister() and
drm_connector_cleanup() when the device is unbound. However, by then, there
might still be some references held to that connector, including by the
userspace that might still have the DRM device open.
Let's switch to a DRM-managed initialization to clean up after ourselves
only once the DRM device has been last closed.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The current code will call drm_encoder_cleanup() when the device is
unbound. However, by then, there might still be some references held to
that encoder, including by the userspace that might still have the DRM
device open.
Let's switch to a DRM-managed initialization to clean up after ourselves
only once the DRM device has been last closed.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
drm_connector_unregister() is only to be used for connectors that have been
registered through drm_connector_register() after drm_dev_register() has
been called. This is our case here so let's remove the call.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Our internal structure that stores the DRM entities structure is allocated
through a device-managed kzalloc.
This means that this will eventually be freed whenever the device is
removed. In our case, the most likely source of removal is that the main
device is going to be unbound, and component_unbind_all() is being run.
However, it occurs while the DRM device is still registered, which will
create dangling pointers, eventually resulting in use-after-free.
Switch to a DRM-managed allocation to keep our structure until the DRM
driver doesn't need it anymore.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The VC4 VEC driver private structure contains only a pointer to the
encoder and connector it implements. This makes the overall structure
somewhat inconsistent with the rest of the driver, and complicates its
initialisation without any apparent gain.
Let's embed the drm_encoder structure (through the vc4_encoder one) and
drm_connector into struct vc4_vec to fix both issues.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
There's no user for that pointer so let's just get rid of it.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Our current code now mixes some resources whose lifetime are tied to the
device (clocks, IO mappings, etc.) and some that are tied to the DRM device
(encoder, bridge).
The device one will be freed at unbind time, but the DRM one will only be
freed when the last user of the DRM device closes its file handle.
So we end up with a time window during which we can call the encoder hooks,
but we don't have access to the underlying resources and device.
Let's protect all those sections with drm_dev_enter() and drm_dev_exit() so
that we bail out if we are during that window.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
drm_connector_unregister() is only to be used for connectors that have been
registered through drm_connector_register() after drm_dev_register() has
been called. This is our case here so let's remove the call.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Our internal structure that stores the DRM entities structure is allocated
through a device-managed kzalloc.
This means that this will eventually be freed whenever the device is
removed. In our case, the most likely source of removal is that the main
device is going to be unbound, and component_unbind_all() is being run.
However, it occurs while the DRM device is still registered, which will
create dangling pointers, eventually resulting in use-after-free.
Switch to a DRM-managed allocation to keep our structure until the DRM
driver doesn't need it anymore.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
There's already a regset in the vc4_crtc structure so there's no need to
duplicate it in vc4_txp.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
There's no user for that pointer so let's just get rid of it.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
devm_pm_runtime_enable() simplifies the driver a bit since it will call
pm_runtime_disable() automatically through a device-managed action.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Whenever the device and driver are unbound, the main device and all the
subdevices will be removed by calling their unbind() method.
However, the DRM device itself will only be freed when the last user will
have closed it.
It means that there is a time window where the device and its resources
aren't there anymore, but the userspace can still call into our driver.
Fortunately, the DRM framework provides the drm_dev_enter() and
drm_dev_exit() functions to make sure our underlying device is still there
for the section protected by those calls. Let's add them to the HDMI driver.
Acked-by: Thomas Zimmermann <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|