| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add "blue-and-red-wiring"-device tree property and update devicetree
binding document.
The red and blue components are reversed between 24 and 16 bit modes
on am335x LCDC output pins. To get 24 RGB format the red and blue
wires has to be crossed and this in turn causes 16 colors output to be
in BGR format. With straight wiring the 16 color is RGB and 24 bit is
BGR.
The new property describes whether the red and blue wires are crossed
or not. If the property is not present or its value is not recognized
the legacy mode is assumed. The legacy configuration supports RGB565,
RGB888 and XRGB8888 formats. However, depending on wiring, the red and
blue colors are swapped in either 16 or 24-bit color modes.
For more details see section 3.1.1 in AM335x Silicon Errata:
http://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=sprz360
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Write DMA base and ceiling address with a single instruction, if
available. This should make it more unlikely that LCDC would fetch the
DMA addresses in the middle of an update. Having bad combination of
addresses in dma base and ceiling (e.g base > ceiling) can cause
unpredictaple behavior in LCDC.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
drm_helper_disable_unused_functions() should not be called by atomic
drivers.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This got accidentally dropped in the fixed commit and is required for
the driver to properly work on the rev1 IP, such as found on the LCDK.
Fixes: 2b2080d7e9ae ("drm/tilcdc: Get rid of complex ping-pong mechanism")
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
The LCDC seems to expect its framebuffer ceiling address pointer to be
an inclusive bound. The IP rev2 seems to cope with that but rev1 (as
found on the LCDK) don't.
Also note that this is what the framebuffer code does in da8xx-fb.c.
Since, as the TRM puts it, "The 2 LSBs are hardwired to 00b", the
dma_addr_t can be decremented without cast.
I tested it with a v2 (AM335x, rev 0x4F201000) and an LCDK (v1).
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
In function tilcdc_get_external_components the check for
the remote port parent is not correct. We need a '||' instead of
an '&&'.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Drivers may set the NO_DISABLE_AFTER_MODESET flag in the 'flags' parameter
of the helper drm_atomic_helper_commit_planes() if the relevant display
controllers(e.g., IPUv3 for imx-drm) require to disable a CRTC's planes
when the CRTC is disabled. The helper would skip the ->atomic_disable
call for a plane if the CRTC of the old plane state needs a modesetting
operation. Of course, the drivers need to disable the planes in their CRTC
disable callbacks since no one else would do that.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472461923-14364-1-git-send-email-gnuiyl@gmail.com
|
|
Change tilcdc_crtc_page_flip() to tilcdc_crtc_update_fb(). The
function is not used as a page_flip() callback anymore so it is only
confusing to call it that. The function should only be used by dummy
primary plane commit() callback.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Remove unnecessary pm_runtime_get() and *_put() calls from commit
phase callbacks. Those calls are not needed since we have the whole
commit phase between pm_runtime_get_sync() and pm_runtime_put_sync().
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Get rid of legacy dpms mechanism. This simplifies the code quite a
bit. The old start() and stop() functions become tilcdc_crtc_enable()
and *_disable(). The functions are added with all the necessary
mechanisms from the old dpms function and they are used directly as
the crtc helper enable() and disable() callbacks.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Use drm_atomic_helper_resume/suspend() and get rid off all the obsolete
register level context restoring code.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Enable and disable interrupts in crtc start() and stop(). None of the
interrupts can fire if CRTC is disabled, so it is cleaner - when
considering suspend/resume code etc. - to enable the interrupts when
CRTC is turned on and to disable them when CRTC is turned off.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Add atomic modeset helpers to tfp410 connector funcs. Property handling
related helpers, atomic reset helper, and new dpms helper is needed in
connector for atomic modeseting to work. The default helper functions
are enough.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Set crtc panel info at init phase. Setting it at prepare callback does
it multiple times for no good reason and it is also too late when atomic
modeset is used.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Add atomic modeset helpers to panel connector funcs. Property handling
related helpers, atomic reset helper, and new dpms helper is needed in
connector for atomic modeseting to work. The default helper functions
are enough.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Set crtc panel info at init phase. Setting it at prepare callback does
it multiple times for no good reason and it is also too late when atomic
modeset is used.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Remove tilcdc_verify_fb(). The tilcdc_verify_fb() function is not
needed because the same checks are implemented in
tilcdc_plane_atomic_check().
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Remove obsolete crtc helper functions. These are not needed when
atomic modeset is used.
Note that the drm_crtc_helper_funcs mode_fixup() is still needed. The
crtc's check() callback can not do its job here.
The plane's check() callback needs to set drm_crtc_state's
->mode_changed to true if the pixel format for the framebuffer
changes. Because of this drm_mode_config_funcs atomic_check() callback
needs to call drm_atomic_helper_check_modeset() once more after it has
called drm_atomic_helper_check_planes(). If the fixing of the
adjusted_mode would be done in drm_crtc_helper_funcs atomic_check()
callback, it would get over written by the extra
drm_atomic_helper_check_modeset() call.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Set DRIVER_ATOMIC and use atomic helpers and rename commit and prepare
crtc helpers to enable and disable. This makes the final jump to mode
setting, but there is lot of obsolete code to clean up.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Add drm_mode_config_reset() call to tilcdc_load(). This is need to
initialize atomic state variables at load time.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Add atomic mode config funcs. The atomic_commit implementation is a
copy-paste from drm_atomic_helper_commit(), leaving out the async
test. The similar copy-paste implementation appears to be used in many
other drivers too. The standard drm_atomic_helper_check() is used for
checking.
The drm_atomic_helper_check() can not be used in drm_mode_config_funcs
atomic_check() callback because the plane's check implementation may
update crtc state's ->mode_changed flag. Because of this the
drm_atomic_helper_check_modeset() has to be called once more after
drm_atomic_helper_check_planes() (see drm_atomic_helper_check_modeset()
documentation).
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Add tilcdc_crtc_atomic_check(). Checks the display mode validity and
the presence of the mandatory primary plane.
The drm_crtc_helper_funcs mode_fixup() callback is left untouched and
the check function does no try to do its job on purpose, despite what
the mode_fixup() callback's documentations suggests.
The plane's check() callback needs to set drm_crtc_state's
->mode_changed to true if the pixel format for the framebuffer
changes. Because of this drm_mode_config_funcs atomic_check() callback
needs to call drm_atomic_helper_check_modeset() once more after it has
called drm_atomic_helper_check_planes(). If the fixing of the
adjusted_mode would be done in drm_crtc_helper_funcs atomic_check()
callback, it would get over written by the extra
drm_atomic_helper_check_modeset() call.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Add tilcdc_crtc_mode_set_nofb(). The mode_set_nofb() semantics do not
fit well to LCDC, because of the mandatory framebuffer. However, when
the primary plane is required in the check phase, it and the
framebuffer can be found from the atomic state struct.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Initialize dummy primary plane from crtc init.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Add dummy primary plane implementation. LCDC does not really have
planes, only simple framebuffer that is mandatory. This primary plane
implementation has the necessary checks for implementing simple
framebuffer trough DRM plane abstraction. For setting the actual
framebuffer the implementation relies on a CRTC side function.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Make tilcdc_crtc_page_flip() work if crtc is not yet on. The plane
commit sometimes comes before crtc is turned on. The new framebuffer
should be set to scanout also in that case, so that it is there when
crtc is turned on at the end of the commit phase.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Make tilcdc_crtc_page_flip() public for dummy plane implementation to use.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Fix tilcdc component master unloading. If a subcomponent module
(tda998x in this case) is unloaded before its master (tilcdc in this
case), it calls drm_put_dev() and it should not be called again by
the master when its module is unloaded. However component_master_del()
must still be called and the check if the drm_put_dev() has been
called must be in component_master_ops unbind() callback, not in
platform_driver remove() callback.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Avoid error print by of_graph_get_next_endpoint() if there is no ports
present.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Add drm_crtc_vblank_on() and *_off() calls to start() and stop()
functions, to make sure any vblank waits etc. gets properly cleaned
up.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Increase time out for waiting frame done interrupt. 50ms is long
enough for the usual display modes (50 Hz or higher refresh rate), but
it may be a bit tight for some unusual mode.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Move wait queue waiting of LCDC_FRAME_DONE IRQ from tilcdc_crtc_dpms()
into stop() function. This is just a cleanup and enables independent
use of stop() function.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Reorder the IRQ function so that the write to LCDC_END_OF_INT_IND_REG
is done last. The write to LCDC_END_OF_INT_IND_REG indicates to LCDC
that the interrupt service routine has completed (see section
13.3.6.1.6 in AM335x TRM). This is needed if LCDC's ipgvmodirq module
is configured for pulse interrupts.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Move LCDC_SYNC_LOST handling inside if (ver == 2) statement.
LCDC_SYNC_LOST interrupt status bit is only defined for version 2
silicon.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Restore old dpms state in pm_resume(). The dpms is turned off in
pm_suspend() and it should be restored to its original state in
pm_resume(). Without this patch the display is left blanked after a
suspend/resume cycle.
Fixes commit 614b3cfeb8d2 ("drm/tilcdc: disable the lcd controller/dma
engine when suspend invoked")
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
Currently enabling TI LCDC DRM support automatically pulls in
fbdev dependency. However this dep is unnecessary since
DRM core already handles this for us (DRM_FBDEV_EMULATION).
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1468586897-32298-13-git-send-email-tjakobi@math.uni-bielefeld.de
|
|
Remove legacy usage of drm_handle_vblank()
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1467677092-5089-6-git-send-email-gustavo@padovan.org
|
|
We already have a fallback in place to fill out the unique from
dev->unique, which is set to something reasonable in drm_dev_alloc.
Which means we only need to have a special set_busid for pci devices,
to be able to care the backwards compat code for drm 1.1 around, which
libdrm still needs.
While developing and testing this patch things blew up in really
interesting ways, and the code is rather confusing in naming things
between the kernel code, ioctl #defines and libdrm. For the next brave
dragon slayer, document all this madness properly in the userspace
interface section of gpu.tmpl.
v2: Make drm_dev_set_unique static and update kerneldoc.
v3: Entire rewrite, plus document what's going on for posterity in the
gpu docbook uapi section.
v4: Drop accidental amdgpu hunk (Emil).
v5: Drop accidental omapdrm vblank counter change (Emil).
v6: Rebase on top of the sphinx conversion.
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> (virt_gpu)
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
No dev->struct_mutex anywhere to be seen.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464630800-30786-14-git-send-email-daniel.vetter@ffwll.ch
|
|
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull drm updates from Dave Airlie:
"Here's the main drm pull request for 4.7, it's been a busy one, and
I've been a bit more distracted in real life this merge window. Lots
more ARM drivers, not sure if it'll ever end. I think I've at least
one more coming the next merge window.
But changes are all over the place, support for AMD Polaris GPUs is in
here, some missing GM108 support for nouveau (found in some Lenovos),
a bunch of MST and skylake fixes.
I've also noticed a few fixes from Arnd in my inbox, that I'll try and
get in asap, but I didn't think they should hold this up.
New drivers:
- Hisilicon kirin display driver
- Mediatek MT8173 display driver
- ARC PGU - bitstreamer on Synopsys ARC SDP boards
- Allwinner A13 initial RGB output driver
- Analogix driver for DisplayPort IP found in exynos and rockchip
DRM Core:
- UAPI headers fixes and C++ safety
- DRM connector reference counting
- DisplayID mode parsing for Dell 5K monitors
- Removal of struct_mutex from drivers
- Connector registration cleanups
- MST robustness fixes
- MAINTAINERS updates
- Lockless GEM object freeing
- Generic fbdev deferred IO support
panel:
- Support for a bunch of new panels
i915:
- VBT refactoring
- PLL computation cleanups
- DSI support for BXT
- Color manager support
- More atomic patches
- GEM improvements
- GuC fw loading fixes
- DP detection fixes
- SKL GPU hang fixes
- Lots of BXT fixes
radeon/amdgpu:
- Initial Polaris support
- GPUVM/Scheduler/Clock/Power improvements
- ASYNC pageflip support
- New mesa feature support
nouveau:
- GM108 support
- Power sensor support improvements
- GR init + ucode fixes.
- Use GPU provided topology information
vmwgfx:
- Add host messaging support
gma500:
- Some cleanups and fixes
atmel:
- Bridge support
- Async atomic commit support
fsl-dcu:
- Timing controller for LCD support
- Pixel clock polarity support
rcar-du:
- Misc fixes
exynos:
- Pipeline clock support
- Exynoss4533 SoC support
- HW trigger mode support
- export HDMI_PHY clock
- DECON5433 fixes
- Use generic prime functions
- use DMA mapping APIs
rockchip:
- Lots of little fixes
vc4:
- Render node support
- Gamma ramp support
- DPI output support
msm:
- Mostly cleanups and fixes
- Conversion to generic struct fence
etnaviv:
- Fix for prime buffer handling
- Allow hangcheck to be coalesced with other wakeups
tegra:
- Gamme table size fix"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits)
drm/edid: add displayid detailed 1 timings to the modelist. (v1.1)
drm/edid: move displayid validation to it's own function.
drm/displayid: Iterate over all DisplayID blocks
drm/edid: move displayid tiled block parsing into separate function.
drm: Nuke ->vblank_disable_allowed
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
...
|
|
This adds one more argument to of_fdt_unflatten_tree() to specify
the parent node of the FDT blob that is going to be unflattened.
In the result, the function can be used to unflatten FDT blob that
represents device sub-tree in PowerNV PCI hotplug driver.
Cc: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Replace the legacy drm_send_vblank_event() with the new helper function.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460656118-16766-11-git-send-email-gustavo@padovan.org
|
|
Use devm_kzalloc() and devm_kcalloc() for private data allocation at
driver load time.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Initialize port device node pointer in the tilcdc crtc. Fixes "Falling
back to first CRTC" warning from tda998x driver.
The tda998x encoder driver calls drm_of_find_possible_crtcs() to
initialize possible_crtcs of struct drm_encoder. The crtc->port needs
to be initialized for drm_of_find_possible_crtcs() to work.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Disable the sync lost interrupt if it fires on every frame for 50
consecutive frames in a row. This is relatively sure sign of the sync
lost interrupt being stuck and firing on every frame even if the
display otherwise appears to work OK.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add ratelimited prints on sync lost and FIFO underrun interrupts.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Removes the duplicate LCDC_INT_ENABLE_SET_REG-entry in registers array.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Fix interrupt enable/disable code for version 2 tilcdc. In version 2
tilcdc there is a separate register for disabling interrupts. Writing
0 to enable registers bits does not have any effect. The interrupt
clear register works the same way, writing 1 to specific bit disables
the interrupt and writing 0 does not have any effect.
The "bug" that is fixed here does not really do any harm since the
interrupts are enabled only once in the power up and disabled before
power down.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Do not update the next frame buffer close to vertical blank. This is
to avoid situation when the frame changes between writing of
LCDC_DMA_FB_BASE_ADDR_0_REG and LCDC_DMA_FB_CEILING_ADDR_0_REG.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|