| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
https://gitlab.freedesktop.org/drm/tegra into drm-next
drm/tegra: Changes for v6.2-rc1
This contains a bunch of cleanups across the board as well as support
for the NVDEC hardware found on the Tegra234 SoC.
Signed-off-by: Dave Airlie <[email protected]>
From: Thierry Reding <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The symbol is not used outside of the file, so mark it static.
Fixes the following warning:
./drivers/gpu/drm/tegra/submit.c:136:28: warning: symbol 'gather_bo_ops'
was not declared. Should it be static?
Signed-off-by: ruanjinjie <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
devm_gpiod_get_from_of_node() is going away and GPIO consumers should
use generic device/firmware node APIs to fetch GPIOs assigned to them.
Switch the driver to use devm_fwnode_gpiod_get() instead.
Signed-off-by: Dmitry Torokhov <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Add support for the Tegra234 version of NVDEC to the NVDEC driver.
This version sports a RISC-V controller and requires a few additional
clocks. After firmware has been loaded, the behavior is, however,
backwards compatible.
Signed-off-by: Mikko Perttunen <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Add helper code for booting RISC-V based engines where firmware is
located in a carveout.
Signed-off-by: Mikko Perttunen <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
NVDEC on Tegra234 requires multiple clocks. Add support for that.
Signed-off-by: Mikko Perttunen <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Prefer the parsed results for is_hdmi in display info over calling
drm_detect_hdmi_monitor().
Cc: Thierry Reding <[email protected]>
Cc: [email protected]
Signed-off-by: Jani Nikula <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Add the missing clk_disable_unprepare() before return from
tegra_dc_probe() in the error handling path.
Fixes: f68ba6912bd2 ("drm/tegra: dc: Link DC1 to DC0 on Tegra20")
Signed-off-by: Zhang Zekun <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
This patch fixes the following Coccinelle warning:
drivers/gpu/drm/tegra/submit.c:173: WARNING opportunity for vmemdup_user
Use vmemdup_user() rather than duplicating its implementation.
This is a little bit restricted to reduce false positives.
Signed-off-by: Qing Wang <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
On Tegra234, engines that are programmed through Host1x channels can
be attached to either the NISO0 or NISO1 SMMU. Because of that, when
selecting a context device to use with an engine, we need to select
one that is also attached to the same SMMU.
Add a parameter to host1x_memory_context_alloc to specify which device
we are allocating a context for, and use it to pick an appropriate
context device.
Signed-off-by: Mikko Perttunen <[email protected]>
[[email protected]: update !IOMMU_API stub signature]
Signed-off-by: Thierry Reding <[email protected]>
|
|
Linux 6.1-rc6
This is needed for drm-misc-next and tegra.
Signed-off-by: Dave Airlie <[email protected]>
|
|
Since commit c7e3ca515e78 ("iommu/tegra: gart: Do not register with
bus") quite some time ago, the GART driver has effectively disabled
itself to avoid issues with the GPU driver expecting it to work in ways
that it doesn't. As of commit 57365a04c921 ("iommu: Move bus setup to
IOMMU device registration") that bodge no longer works, but really the
GPU driver should be responsible for its own behaviour anyway. Make the
workaround explicit.
Reported-by: Jon Hunter <[email protected]>
Suggested-by: Dmitry Osipenko <[email protected]>
Signed-off-by: Robin Murphy <[email protected]>
Tested-by: Jon Hunter <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
When userspace mmaps dma-buf's fd, the dma-buf reservation lock must be
held. Add locking sanity checks to the dma-buf mmaping callbacks of DRM
drivers to ensure that the locking assumptions won't regress in future.
Suggested-by: Daniel Vetter <[email protected]>
Signed-off-by: Dmitry Osipenko <[email protected]>
Acked-by: Christian König <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Implement the fbdev's read/write helpers with the same functions. Use
the generic fbdev's code as template. Convert all drivers.
DRM's fb helpers must implement regular I/O functionality in struct
fb_ops and possibly perform a damage update. Handle all this in the
same functions and convert drivers. The functionality has been used
as part of the generic fbdev code for some time. The drivers don't
set struct drm_fb_helper.fb_dirty, so they will not be affected by
damage handling.
For I/O memory, fb helpers now provide drm_fb_helper_cfb_read() and
drm_fb_helper_cfb_write(). Several drivers require these. Until now
tegra used I/O read and write, although the memory buffer appears to
be in system memory. So use _sys_ helpers now.
v3:
* fix docs (Javier)
v2:
* rebase onto vmwgfx changes
Signed-off-by: Thomas Zimmermann <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Rename drm_fb_helper_unregister_fbi() to drm_fb_helper_unregister_info()
as part of unifying the naming within fbdev helpers. Adapt drivers. No
functional changes.
Signed-off-by: Thomas Zimmermann <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Rename drm_fb_helper_alloc_fbi() to drm_fb_helper_alloc_info() as
part of unifying the naming within fbdev helpers. Adapt drivers. No
functional changes.
Signed-off-by: Thomas Zimmermann <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Rename struct drm_fb_helper.fbdev to info. The current name is
misleading as it overlaps with generic fbdev naming conventions.
Adapt to the usual naming in fbdev drivers by calling the field
'info'. No functional changes.
Signed-off-by: Thomas Zimmermann <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The fb_base in struct drm_mode_config has been unused for a long time.
Some drivers set it and some don't leading to a very confusing state
where the variable can't be relied upon, because there's no indication
as to which driver sets it and which doesn't.
The only usage of fb_base is internal to two drivers so instead of trying
to force it into all the drivers to get it into a coherent state
completely remove it.
Signed-off-by: Zack Rusin <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Reviewed-by: Thomas Zimmermann <[email protected]>
Acked-by: Christian König <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Prepare Tegra DRM driver to the common dynamic dma-buf locking convention
by starting to use the unlocked versions of dma-buf API functions.
Acked-by: Christian König <[email protected]>
Signed-off-by: Dmitry Osipenko <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Rename "FB CMA" helpers to "FB DMA" helpers - considering the hierarchy
of APIs (mm/cma -> dma -> fb dma) calling them "FB DMA" seems to be
more applicable.
Besides that, commit e57924d4ae80 ("drm/doc: Task to rename CMA helpers")
requests to rename the CMA helpers and implies that people seem to be
confused about the naming.
In order to do this renaming the following script was used:
```
#!/bin/bash
DIRS="drivers/gpu include/drm Documentation/gpu"
REGEX_SYM_UPPER="[0-9A-Z_\-]"
REGEX_SYM_LOWER="[0-9a-z_\-]"
REGEX_GREP_UPPER="(${REGEX_SYM_UPPER}*)(FB)_CMA_(${REGEX_SYM_UPPER}*)"
REGEX_GREP_LOWER="(${REGEX_SYM_LOWER}*)(fb)_cma_(${REGEX_SYM_LOWER}*)"
REGEX_SED_UPPER="s/${REGEX_GREP_UPPER}/\1\2_DMA_\3/g"
REGEX_SED_LOWER="s/${REGEX_GREP_LOWER}/\1\2_dma_\3/g"
# Find all upper case 'CMA' symbols and replace them with 'DMA'.
for ff in $(grep -REHl "${REGEX_GREP_UPPER}" $DIRS)
do
sed -i -E "$REGEX_SED_UPPER" $ff
done
# Find all lower case 'cma' symbols and replace them with 'dma'.
for ff in $(grep -REHl "${REGEX_GREP_LOWER}" $DIRS)
do
sed -i -E "$REGEX_SED_LOWER" $ff
done
# Replace all occurrences of 'CMA' / 'cma' in comments and
# documentation files with 'DMA' / 'dma'.
for ff in $(grep -RiHl " cma " $DIRS)
do
sed -i -E "s/ cma / dma /g" $ff
sed -i -E "s/ CMA / DMA /g" $ff
done
```
Only a few more manual modifications were needed, e.g. reverting the
following modifications in some DRM Kconfig files
- select CMA if HAVE_DMA_CONTIGUOUS
+ select DMA if HAVE_DMA_CONTIGUOUS
as well as manually picking the occurrences of 'CMA'/'cma' in comments and
documentation which relate to "FB CMA", but not "GEM CMA".
This patch is compile-time tested building a x86_64 kernel with
`make allyesconfig && make drivers/gpu/drm`.
Acked-by: Sam Ravnborg <[email protected]>
Acked-by: Thomas Zimmermann <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Signed-off-by: Danilo Krummrich <[email protected]>
Reviewed-by: Liviu Dudau <[email protected]> #drivers/gpu/drm/arm
Signed-off-by: Sam Ravnborg <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Remove the include statement for drm_plane_helper.h from all the files
that don't need it. Althogh the header file is almost empty, many drivers
include it somewhere.
Signed-off-by: Thomas Zimmermann <[email protected]>
Reviewed-by: Sam Ravnborg <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
https://gitlab.freedesktop.org/drm/tegra into drm-next
drm/tegra: Changes for v5.20-rc1
The bulk of these changes adds support for context isolation for the
various supported host1x engines, as well as support for the hardware
found on the new Tegra234 SoC generation.
There's also a couple of fixes and cleanups. To round things off, the
device tree bindings are converted to the new json-schema format that
allows DTBs to be validated.
Signed-off-by: Dave Airlie <[email protected]>
From: Thierry Reding <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Use the devm_platform_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately. Make the
code simpler without functional changes.
Reported-by: Zeal Robot <[email protected]>
Signed-off-by: Lv Ruyi <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Even though the IOVA API never actually needed it, iova.h is still
carrying an include of dma-mapping.h, now solely for the sake of not
breaking tegra-drm. Fix that properly.
Signed-off-by: Robin Murphy <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
The code assumes that Tegra GEM is permanently vmapped, which is not
true for the scattered buffers. After converting Tegra video decoder
driver to V4L API, we're now getting a BUG_ON from dma-buf core on playing
video using libvdpau-tegra on T30+ because tegra_gem_prime_vmap() sets
vaddr to NULL. Older pre-V4L video decoder driver wasn't vmapping dma-bufs.
Fix it by actually vmapping the exported GEMs.
Cc: [email protected]
Signed-off-by: Dmitry Osipenko <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
drivers/gpu/drm/tegra/vic.c:326:12: error: ‘vic_runtime_suspend’ defined but not used [-Werror=unused-function]
static int vic_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/tegra/vic.c:292:12: error: ‘vic_runtime_resume’ defined but not used [-Werror=unused-function]
static int vic_runtime_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~
Mark it as __maybe_unused.
Signed-off-by: YueHaibing <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Add Tegra234 support for VIC. It is backwards compatible with
Tegra194.
Signed-off-by: Mikko Perttunen <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Implement the get_streamid_offset and can_use_memory_ctx callbacks
required for supporting context isolation. Since old firmware on VIC
cannot support context isolation without hacks that we don't want to
implement, check the firmware binary to see if context isolation
should be enabled.
Signed-off-by: Mikko Perttunen <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
For engines that support context isolation, allocate a context when
opening a channel, and set up stream ID offset and context fields
when submitting a job.
As of this commit, the stream ID offset and fallback stream ID
are not used when context isolation is disabled. However, with
upcoming patches that enable a full featured job opcode sequence,
these will be necessary.
Signed-off-by: Mikko Perttunen <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
NVDEC's TRANSCFG register is at a different offset than VIC.
This becomes a problem now when context isolation is enabled and
the reset value of the register is no longer sufficient.
Signed-off-by: Mikko Perttunen <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
The DMACTX field determines which context, as specified in the
TRANSCFG register, is used. While during boot it doesn't matter
which is used, later on it matters and this value is reused by
the firmware.
Signed-off-by: Mikko Perttunen <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
drm_crtc.h has no need for drm_blend.h, so don't include it.
Avoids useless rebuilds of the entire universe when
touching drm_blend.h.
Quite a few placs do currently depend on drm_blend.h without
actually including it directly. All of those need to be fixed
up.
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Acked-by: Sam Ravnborg <[email protected]>
Acked-by: Jani Nikula <[email protected]>
|
|
drm_crtc.h has no need for drm_frambuffer.h, so don't include it.
Avoids useless rebuilds of the entire universe when
touching drm_framebuffer.h.
Quite a few placs do currently depend on drm_framebuffer.h without
actually including it directly. All of those need to be fixed
up.
v2: Fix up msm some more
v2: Deal with ingenic and shmobile as well
Signed-off-by: Ville Syrjälä <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Acked-by: Sam Ravnborg <[email protected]>
Acked-by: Jani Nikula <[email protected]>
|
|
https://gitlab.freedesktop.org/drm/tegra into drm-next
drm/tegra: Changes for v5.19-rc1
Only a few fixes this time, and some debuggability improvements.
Signed-off-by: Dave Airlie <[email protected]>
From: Thierry Reding <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
When mapping the DMA-BUF attachment fails, map->sgt will be an ERR_PTR-
encoded error code and the cleanup code would try to free that memory,
which obviously would fail.
Zero out that pointer after extracting the error code when this happens
so that kfree() can do the right thing.
Reported-by: kernel test robot <[email protected]>
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
SCDC is the Status and Control Data Channel for HDMI. Move the SCDC
helpers into display/ and split the header into files for core and
helpers. Update all affected drivers. No functional changes.
To avoid the proliferation of Kconfig options, SCDC is part of DRM's
support for HDMI. If necessary, a new option could make SCDC an
independent feature.
Signed-off-by: Thomas Zimmermann <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Replace the DP-helper module with a display-helper module. The
support for DisplayPort becomes an internal option that drivers
have to select. Update all related Kconfig and Makefile rules.
Besides the existing code for DisplayPort, the new module will
contain helpers for other video-output standards, such as HDMI.
Drivers will have to select their required video-output helpers.
Linking all display-related code into a single module avoids the
proliferation of small kernel modules.
The module parameters drm_dp_cec_unregister_delay, dp_aux_i2c_speed_khz,
and dp_aux_i2c_transfer_size are moving from the drm_dp_helper namespace
to drm_display_helper.
v2:
* mention module parameters in commit message (Javier)
* distiguish between display module and DP support in Kconfig
* update Makefile rules for DP helpers
* move Kconfig rules into separate file under display/
Signed-off-by: Thomas Zimmermann <[email protected]>
Reviewed-by: Lyude Paul <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Rename dp/ to display/ to account for additional display-related
helpers, such as HDMI. Update all related include statements. No
functional changes.
Various drivers, such as i915 and amdgpu, use similar naming scheme
by putting code for video-output standards into a local display/
directory. The new directory's name is aligned with this convention.
v2:
* update commit message (Javier)
Signed-off-by: Thomas Zimmermann <[email protected]>
Reviewed-by: Lyude Paul <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
Reviewed-by: Alex Deucher <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The use of the old-style SET_RUNTIME_PM_OPS() and
SET_SYSTEM_SLEEP_PM_OPS() macros requires function definitions
to be hidden to avoid
drivers/gpu/drm/tegra/vic.c:326:12: error: 'vic_runtime_suspend' defined but not used [-Werror=unused-function]
326 | static int vic_runtime_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/tegra/vic.c:292:12: error: 'vic_runtime_resume' defined but not used [-Werror=unused-function]
292 | static int vic_runtime_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~
Use the new-style SYSTEM_SLEEP_PM_OPS() and RUNTIME_PM_OPS() instead.
Fixes: 1e15f5b911d6 ("drm/tegra: vic: Stop channel on suspend")
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.18:
UAPI Changes:
Cross-subsystem Changes:
- Improve performance of some fbdev ops, in some cases up to 6x faster.
Core Changes:
- Some small DP fixes.
- Find panels in subnodes of OF devices, and add of_get_drm_panel_display_mode
to retrieve mode.
- Add drm_object_property_get_default_value and use it for resetting
zpos in plane state reset, removing the need for individual drivers
to do it.
- Same for color encoding and color range props.
- Update panic handling todo doc.
- Add todo that format conversion helpers should be sped up similarly to fbdev ops.
Driver Changes:
- Add panel orientation property to simpledrm for quirked panels.
- Assorted small fixes to tiny/repaper, nouveau, stm, omap, ssd130x.
- Add crc support to stm/ltdc.
- Add MIPI DBI compatible SPI driver
- Assorted small fixes to tiny panels and bridge drivers.
- Add AST2600 support to aspeed.
Signed-off-by: Dave Airlie <[email protected]>
From: Maarten Lankhorst <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
https://gitlab.freedesktop.org/drm/tegra into drm-next
drm/tegra: Changes for v5.18-rc1
This contains a couple more minor fixes that didn't seem urgent enough
for v5.17. On top of that this improves YUV format support on older
chips.
Signed-off-by: Dave Airlie <[email protected]>
From: Thierry Reding <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Signed-off-by: Thierry Reding <[email protected]>
|
|
The NV12, NV21, NV16, NV61, NV24 and NV42 formats are supported by
Tegra114 and later display hardware. Add the necessary programming to
allow them to be used.
Note that this does not work for Tegra186 and later yet because those
generations have a different display architecture that doesn't support
the same formats.
Signed-off-by: Thierry Reding <[email protected]>
|
|
Use the correct pitch when programming the DC_WIN_PLANAR_STORAGE_UV
register's PITCH_U field to ensure the correct value is used in all
cases. This isn't currently causing any problems because the pitch
for both U and V planes is always the same.
Signed-off-by: Thierry Reding <[email protected]>
|
|
This backmerges v5.17-rc6 so I can merge some amdgpu and some tegra changes on top.
Signed-off-by: Dave Airlie <[email protected]>
|
|
Fix the following coccicheck REVIEW:
./drivers/gpu/drm/tegra/dpaux.c:282:13-16 REVIEW Unneeded variable
Reported-by: Zeal Robot <[email protected]>
Signed-off-by: chiminghao <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore. Add put_device() call to fix this.
Fixes: e94236cde4d5 ("drm/tegra: dsi: Add ganged mode support")
Signed-off-by: Miaoqian Lin <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
The link_status array was not large enough to read the Adjust Request
Post Cursor2 register, so remove the common helper function to avoid
an OOB read, found with a -Warray-bounds build:
drivers/gpu/drm/drm_dp_helper.c: In function 'drm_dp_get_adjust_request_post_cursor':
drivers/gpu/drm/drm_dp_helper.c:59:27: error: array subscript 10 is outside array bounds of 'const u8[6]' {aka 'const unsigned char[6]'} [-Werror=array-bounds]
59 | return link_status[r - DP_LANE0_1_STATUS];
| ~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/drm_dp_helper.c:147:51: note: while referencing 'link_status'
147 | u8 drm_dp_get_adjust_request_post_cursor(const u8 link_status[DP_LINK_STATUS_SIZE],
| ~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Replace the only user of the helper with an open-coded fetch and decode,
similar to drivers/gpu/drm/amd/display/dc/core/dc_link_dp.c.
Cc: Daniel Vetter <[email protected]>
Cc: Maarten Lankhorst <[email protected]>
Cc: Maxime Ripard <[email protected]>
Cc: Thomas Zimmermann <[email protected]>
Cc: David Airlie <[email protected]>
Cc: [email protected]
Fixes: 79465e0ffeb9 ("drm/dp: Add helper to get post-cursor adjustments")
Signed-off-by: Kees Cook <[email protected]>
Reviewed-by: Gustavo A. R. Silva <[email protected]>
Reviewed-by: Jani Nikula <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Thierry Reding <[email protected]>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.18:
UAPI Changes:
Cross-subsystem Changes:
- Split out panel-lvds and lvds dt bindings .
- Put yes/no on/off disabled/enabled strings in linux/string_helpers.h
and use it in drivers and tomoyo.
- Clarify dma_fence_chain and dma_fence_array should never include eachother.
- Flatten chains in syncobj's.
- Don't double add in fbdev/defio when page is already enlisted.
- Don't sort deferred-I/O pages by default in fbdev.
Core Changes:
- Fix missing pm_runtime_put_sync in bridge.
- Set modifier support to only linear fb modifier if drivers don't
advertise support.
- As a result, we remove allow_fb_modifiers.
- Add missing clear for EDID Deep Color Modes in drm_reset_display_info.
- Assorted documentation updates.
- Warn once in drm_clflush if there is no arch support.
- Add missing select for dp helper in drm_panel_edp.
- Assorted small fixes.
- Improve fb-helper's clipping handling.
- Don't dump shmem mmaps in a core dump.
- Add accounting to ttm resource manager, and use it in amdgpu.
- Allow querying the detected eDP panel through debugfs.
- Add helpers for xrgb8888 to 8 and 1 bits gray.
- Improve drm's buddy allocator.
- Add selftests for the buddy allocator.
Driver Changes:
- Add support for nomodeset to a lot of drm drivers.
- Use drm_module_*_driver in a lot of drm drivers.
- Assorted small fixes to bridge/lt9611, v3d, vc4, vmwgfx, mxsfb, nouveau,
bridge/dw-hdmi, panfrost, lima, ingenic, sprd, bridge/anx7625, ti-sn65dsi86.
- Add bridge/it6505.
- Create DP and DVI-I connectors in ast.
- Assorted nouveau backlight fixes.
- Rework amdgpu reset handling.
- Add dt bindings for ingenic,jz4780-dw-hdmi.
- Support reading edid through aux channel in ingenic.
- Add a drm driver for Solomon SSD130x OLED displays.
- Add simple support for sharp LQ140M1JW46.
- Add more panels to nt35560.
Signed-off-by: Dave Airlie <[email protected]>
From: Maarten Lankhorst <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Replace dev_printk() with a generic dev_err_probe() helper which silences
noisy error messages about deferred probe and makes easy to debug failing
deferred probe by printing notification about the failure to KMSG in the
end of kernel booting process and by adding failing device and the reason
of deferred probe to devices_deferred of debugfs. This was proven to be
useful in the case of eDP driver regression by immediately showing why
display driver was failing when user asked for help, otherwise it would've
been much more difficult to debug such problems on a third party device
that doesn't have developer setup.
Signed-off-by: Dmitry Osipenko <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|