aboutsummaryrefslogtreecommitdiff
path: root/drivers/gpu/drm/panel/panel-simple.c
AgeCommit message (Collapse)AuthorFilesLines
2016-03-17Merge tag 'drm/panel/for-4.6-rc1' of ↵Dave Airlie1-0/+81
http://anongit.freedesktop.org/git/tegra/linux into drm-next drm/panel: Changes for v4.6-rc1 This contains a refactoring of parts of the DSI core to allow creating DSI devices from non-DSI control busses (i.e. I2C, SPI, ...). Other than that there's support for a couple of new panels as well as a few cleanup patches. * tag 'drm/panel/for-4.6-rc1' of http://anongit.freedesktop.org/git/tegra/linux: drm/bridge: Make (pre/post) enable/disable callbacks optional drm/panel: simple: Add URT UMSH-8596MD-xT panels support dt-bindings: Add URT UMSH-8596MD-xT panel bindings of: Add United Radiant Technology Corporation vendor prefix drm/panel: simple: Support for LG lp120up1 panel dt-bindings: Add LG lp120up1 panel bindings drm/panel: simple: Fix g121x1_l03 hsync/vsync polarity drm/dsi: Get DSI host by DT device node drm/dsi: Add routine to unregister a DSI device drm/dsi: Try to match non-DT DSI devices drm/dsi: Use mipi_dsi_device_register_full() for DSI device creation drm/dsi: Check for CONFIG_OF when defining of_mipi_dsi_device_add()
2016-03-02drm/panel: simple: Add URT UMSH-8596MD-xT panels supportMaciej S. Szmigiero1-0/+54
Add support for United Radiant Technology UMSH-8596MD-xT 7.0" WVGA TFT LCD panels in the simple-panel driver. Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Thierry Reding <treding@nvidia.com>
2016-03-02drm/panel: simple: Support for LG lp120up1 panelJitao Shi1-0/+26
The LG lp120up1 TFT LCD panel with eDP interface is a 12.0" 1920x1280 panel, which can be supported by the simple panel driver. Signed-off-by: Jitao Shi <jitao.shi@mediatek.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2016-03-02drm/panel: simple: Fix g121x1_l03 hsync/vsync polarityAkshay Bhat1-0/+1
Set hsync/vsync to active low for g121x1_l03 panel to match the recommended setting in the datasheet. Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2016-02-25drm/fsl-dcu: use mode flags for hsync/vsync polarityStefan Agner1-0/+1
The current default configuration is as follows: - Invert VSYNC signal (active LOW) - Invert HSYNC signal (active LOW) The mode flags allow to specify the required polarity per mode. Furthermore, none of the current driver settings is actually a standard polarity. This patch applies the current driver default polarities as explicit flags to the display which has been introduced with the driver (NEC WQVGA "nec,nl4827hc19-05b"). The driver now also parses the flags field and applies the configuration accordingly, by using the following values as standard polarities: (e.g. when no flags are specified): - VSYNC signal not inverted (active HIGH) - HSYNC signal not inverted (active HIGH) Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-12-16drm/panel: simple: Add QiaoDian qd43003c0-40Josh Wu1-0/+27
The QiaoDian Xianshi QD43003C0-40 is a 4"3 TFT LCD panel. Timings from the OTA5180A document, ver 0.9, section 10.1.1: http://www.orientdisplay.com/pdf/OTA5180A.pdf Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-12-16drm/panel: add kernel doc for size attributes in panel_descUlrich Ölmann1-0/+4
Document that 'width' and 'height' are measured in millimeters. Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-12-16drm/panel: simple: Add support for Kyocera TCG121XGLP panelLucas Stach1-0/+27
The Kyocera TCG121XGLP panel is an XGA LCD TFT panel connected through LVDS, which can be supported by the simple panel driver. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-11-23drm/panel: simple: Add support for Innolux G121X1-L03Akshay Bhat1-0/+31
Add support for Innolux CheMei 12" G121X1-L03 XGA LVDS display. Datasheet: http://www.azdisplays.com/PDF/G121X1-L03.pdf Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-11-23drm/panel: simple: Add support for BOE TV080WUM-NL0Chris Zhong1-0/+34
The BOE TV080WUM-NL0 is an 8.0", 1200x1920 (WUXGA) TFT-LCD panel connected using four DSI lanes. It can be supported by the simple-panel driver. Signed-off-by: Chris Zhong <zyw@rock-chips.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-08-14drm/panel: Add display timing for Okaya RS800480T-7X0GPGary Bisson1-0/+33
Add support for the Okaya RS800480T-7X0GP to the DRM simple panel driver. The RS800480T-7X0GP is a WVGA (800x480) panel with an 18-bit parallel LCD interface. It supports pixel clocks in the range of 30-40 MHz. This panel details can be found at: http://boundarydevices.com/product/7-800x480-display/ Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-08-14drm/panel: simple: Add support for NEC NL4827HC19-05B 480x272 paneljianwei wang1-0/+27
This adds support for the NEC NL4827HC19-05B 480x272 panel to the DRM simple panel driver. Signed-off-by: Alison Wang <b18965@freescale.com> Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com> Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [treding@nvidia.com: add .bpc field for panel] Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-08-14drm/panel: simple: Add support for AUO B080UAN01Thierry Reding1-0/+31
The AUO B080UAN01 is an 8.0" WUXGA TFT LCD panel connected using four DSI lanes. It can be supported by the simple-panel driver. Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-08-14drm/panel: simple: Correct minimum hsync length of the HannStar HSD070PWW1 panelPhilipp Zabel1-1/+6
According to the data sheet, the minimum horizontal blanking interval is 54 clocks (1 + 52 + 1), but tests with a Nitrogen6X have shown the minimum working horizontal blanking interval to be 60 clocks. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-08-14drm/panel: simple: Add bus format for HannStar HSD070PWW1 LVDS panelPhilipp Zabel1-0/+1
The bus format both specifies the bpc and the way the individual bits get serialized into the 7 LVDS timeslots. While the is only one standard mapping for 6 bpc and so the driver could infer the bit mapping from the bpc alone, there are more options for the 8 bpc case which makes specifiying the bus format mandatory. To keep things consistent across panels and to set a precedent for new panel additions add the proper bus format. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-06-12drm/panel: simple: Add bus format for HannStar HSD100PXN1Philipp Zabel1-0/+1
This patch adds the bus_format field to the HSD100PXN1 panel structure. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-06-12drm/panel: simple: Add display timing for HannStar HSD100PXN1Eric Nelson1-0/+26
Add support for the Hannstar HSD100PXN1 to the DRM simple panel driver. The HSD100PXN1 is an XGA (1024x768) panel with an 18-bit LVDS interface. It supports pixel clocks in the range of 55-75 MHz. This panel is offered for sale by Freescale as a companion part to its' i.MX5x Quick Start board and i.MX6 SABRE platforms with under the name MCIMX-LVDS1. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-05-22drm/panel: simple: Add support for LG LB070WV8 800x480 7" panelHeiko Schocher1-0/+27
This adds support for the LG LB070WV8 7" 800x480 panel to the DRM simple panel driver. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-04-02drm/panel: Add support for Ampire AM-800480R3TMQW-A1H 800x480 7" panelPhilipp Zabel1-0/+28
This adds support for the AM-800480R3TMQW-A1H 7" 800x480 panel to the DRM simple panel driver. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-04-02drm/panel: Add display timing for HannStar HSD070PWW1Philipp Zabel1-13/+13
The HannStar HSD070PWW1 LVDS panel data sheet lists allowed ranges additionally to the typical values for pixel clock rate (64.3-82 MHz) and blanking intervals (54-681 clock cycles horizontally, 3-23 lines vertically). This patch replaces this panel's display mode with the display timing information to describe acceptable timings. Since the HSYNC and VSYNC are unused, the distribution between front porches, back porches, and sync pulse lengths was chosen at will. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-04-02drm/panel: simple: Add display timing supportPhilipp Zabel1-0/+42
The simple panel driver's ->get_modes() implementation calculates the display mode list from the typical timings and the ->get_timings() implementation returns the timings to the connected encoder for mode validation and fixup. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> [treding@nvidia.com: select VIDEOMODE_HELPERS] Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-04-02drm/panel: Add support for OrtusTech COM43H4M85ULC panelPhilipp Zabel1-0/+27
This adds support for the COM43H4M85ULC 3.7" 800x480 panel to the DRM simple panel driver. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-04-02drm/panel: Add bus format for Giantplus GPG482739QS5 panelPhilipp Zabel1-0/+1
This patch adds the bus_format field to the GPG482739QS5 panel structure. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-04-02drm/panel: simple: Add support for AUO b101ean01 panelHuang Lin1-0/+26
The AUO b101ean01 panel is a 10.1" 1280x800 panel which can be supported by the simple panel driver. Signed-off-by: Huang Lin <hl@rock-chips.com> Reviewed-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-04-02drm/panel: simple: Add support for Innolux ZJ070NA-01PMichael Grzeschik1-0/+26
The Innolux ZJ070NA-01P is a 7.0" TFT LCD panel with an integrated LED backlight unit. This panel is used on the Technexion Toucan. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-04-02drm/panel: simple: Add support for Innolux AT043TN24Nicolas Ferre1-0/+28
The Innolux AT043TN24 4.3" WQVGA TFT LCD panel. This panel with backlight is found in PDA 4.3" LCD screen (TM43xx series for instance). Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-04-02drm/panel: simple: Add support for Shelly SCA07010-BFN-LNNBoris BREZILLON1-0/+26
The Shelly SCA07010-BFN-LNN is a 7.0" WVGA TFT LCD panel. This panel with backlight is found in PDA 7" LCD screen (TM70xx series for instance). Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-04-02drm/panel: simple: Add support for Samsung LTN140AT29 panelStéphane Marchesin1-0/+26
This panel is used by the Nyan Blaze board and can be supported by the simple-panel driver. Signed-off-by: Stéphane Marchesin <marcheu@chromium.org> [tomeu.vizoso@collabora.com: add device tree binding document] Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-01-28drm/panel: simple: Add AVIC TM070DDH03 panel supportPhilipp Zabel1-0/+31
The Shanghai AVIC Optoelectronics TM070DDH03 is a 7" 1024x600 TFT LCD panel connecting to a 24-bit RGB LVDS interface. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-01-28drm/panel: simple: Add support for Giantplus GPG482739QS5Philipp Zabel1-0/+26
This patch adds support for the GiantPlus GPG48273QS5 4.3" WQVGA TFT LCD panel to the simple-panel driver. This panel is connected via a parallel bus and uses both HSYNC and VSYNC, whose lengths are unfortunately not clearly defined. The datasheet only specifies the front- and backporch length, but the timing diagram suggests that both sync signals should be asserted for exactly one clock cycle. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-01-21drm: panel: simple-panel: add bus format information for foxlink panelBoris Brezillon1-0/+1
Foxlink's fl500wvr00-a0t supports RGB888 format. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Thierry Reding <treding@nvidia.com>
2015-01-21drm: panel: simple-panel: add support for bus_format retrievalBoris Brezillon1-0/+5
Provide a way to specify panel requirement in terms of supported media bus format (particularly useful for panels connected to an RGB or LVDS bus). Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Thierry Reding <treding@nvidia.com>
2014-12-15Merge branch 'drm-next' of git://people.freedesktop.org/~airlied/linuxLinus Torvalds1-16/+117
Pull drm updates from Dave Airlie: "Highlights: - AMD KFD driver merge This is the AMD HSA interface for exposing a lowlevel interface for GPGPU use. They have an open source userspace built on top of this interface, and the code looks as good as it was going to get out of tree. - Initial atomic modesetting work The need for an atomic modesetting interface to allow userspace to try and send a complete set of modesetting state to the driver has arisen, and been suffering from neglect this past year. No more, the start of the common code and changes for msm driver to use it are in this tree. Ongoing work to get the userspace ioctl finished and the code clean will probably wait until next kernel. - DisplayID 1.3 and tiled monitor exposed to userspace. Tiled monitor property is now exposed for userspace to make use of. - Rockchip drm driver merged. - imx gpu driver moved out of staging Other stuff: - core: panel - MIPI DSI + new panels. expose suggested x/y properties for virtual GPUs - i915: Initial Skylake (SKL) support gen3/4 reset work start of dri1/ums removal infoframe tracking fixes for lots of things. - nouveau: tegra k1 voltage support GM204 modesetting support GT21x memory reclocking work - radeon: CI dpm fixes GPUVM improvements Initial DPM fan control - rcar-du: HDMI support added removed some support for old boards slave encoder driver for Analog Devices adv7511 - exynos: Exynos4415 SoC support - msm: a4xx gpu support atomic helper conversion - tegra: iommu support universal plane support ganged-mode DSI support - sti: HDMI i2c improvements - vmwgfx: some late fixes. - qxl: use suggested x/y properties" * 'drm-next' of git://people.freedesktop.org/~airlied/linux: (969 commits) drm: sti: fix module compilation issue drm/i915: save/restore GMBUS freq across suspend/resume on gen4 drm: sti: correctly cleanup CRTC and planes drm: sti: add HQVDP plane drm: sti: add cursor plane drm: sti: enable auxiliary CRTC drm: sti: fix delay in VTG programming drm: sti: prepare sti_tvout to support auxiliary crtc drm: sti: use drm_crtc_vblank_{on/off} instead of drm_vblank_{on/off} drm: sti: fix hdmi avi infoframe drm: sti: remove event lock while disabling vblank drm: sti: simplify gdp code drm: sti: clear all mixer control drm: sti: remove gpio for HDMI hot plug detection drm: sti: allow to change hdmi ddc i2c adapter drm/doc: Document drm_add_modes_noedid() usage drm/i915: Remove '& 0xffff' from the mask given to WA_REG() drm/i915: Invert the mask and val arguments in wa_add() and WA_REG() drm: Zero out DRM object memory upon cleanup drm/i915/bdw: Fix the write setting up the WIZ hashing mode ...
2014-11-13drm/dsi: Do not require .owner field to be setThierry Reding1-1/+0
Drivers now no longer need to set the .owner field. It will be automatically set at registration time. Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-11-07drm/panel: simple: Update Innolux N116BGE timingsDaniel Kurtz1-6/+6
There are several different models of N116BGE. According to commit 0a2288c06aab ("drm/panel: simple: Add Innolux N116BGE panel support"), the video timings are for the eDP variant. The clock and htotal values added by that patch are out of spec according to the datasheets I have seen for the eDP N116BGE (-EA2 and -EB2). This patch changes the values to the "Typ" values on the datasheet. Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> [tested that these timings work with the Tegra132 Norrin panel] Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-11-07drm/panel: simple: Add support for Hitachi TX23D38VM0CAALucas Stach1-0/+26
The Hitachi TX23D38VM0CAA is a 9" WVGA TFT LCD panel and can be supported by the simple-panel driver. This panel is connected via LVDS and uses the data enable signal for timing. Since HSYNC/VSYNC are ignored, the split between sync length and porches is arbitrary, as long as the complete horizontal blanking interval is 256 clocks, and the vertical blanking interval is 45 lines. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-11-07drm/panel: simple: Add support for Innolux G121I1-L01Lucas Stach1-0/+26
The Innolux G121I1-L01 is a 12.1" TFT LCD panel and can be supported by the simple-panel driver. This panel is connected via LVDS and uses the data enable signal for timing. Since HSYNC/VSYNC are ignored, the split between sync length and porches is arbitrary, as long as the complete horizontal blanking interval is 160 clocks, and the vertical blanking interval is 24 lines. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-11-07drm/panel: simple: Add missing .bpc fieldsThierry Reding1-0/+5
Various panels were missing the .bpc field which encodes the number of bits per color. Not every display driver relies on this value, but since the panels can be used with any display engine it must be specified so that if a driver knows how to differentiate based on this field it can do so. Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-11-07drm/panel: simple: Add AUO B116XW03 panel supportAjay Kumar1-0/+26
The AUO B116XW03 is a 11.6" HD TFT LCD panel connecting to a LVDS interface and with an integrated LED backlight unit. This panel is used on the Samsung Chromebook(XE303C12). Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> [treding@nvidia.com: add missing .bpc field] Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-11-07drm/panel: simple: Add HannStar HSD070PWW1 7.0" WXGA TFT LCD panelPhilipp Zabel1-0/+26
This patch adds support for the HannStar Display Corp. HSD070PWW1 7.0" WXGA TFT LCD panel to the simple-panel driver. The binding documentation is included. This panel is connected via LVDS and uses the data enable signal for timing. Since HSYNC/VSYNC are ignored, the split between sync length and porches is arbitrary, as long as the complete horizontal blanking interval is 160 clocks, and the vertical blanking interval is 23 lines. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-11-06drm/panel: simple: Update calls to gpiod_get*()Alexandre Courbot1-9/+2
Add the new flags argument to calls of (devm_)gpiod_get*() and remove any direction setting code afterwards. Currently both forms (with or without the flags argument) are valid thanks to transitional macros in <linux/gpio/consumer.h>. These macros will be removed once all consumers are updated and the flags argument will become compulsary. Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Acked-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-10-20gpu: drm: panel: drop owner assignment from platform_driversWolfram Sang1-1/+0
A platform_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-09-10drm/panel/simple: add optronics B101XTN01.0 (v3)Rob Clark1-0/+27
LVDS panel, make/model described as: AU Optronics Corporation - B101XTN01.0 (H/W:0A) See: http://www.encore-electronic.com/media/B101XTN01.0.pdf Tested with panel attached to an Inforce IFC6410 board. Signed-off-by: Rob Clark <robdclark@gmail.com>
2014-08-07drm/panel: simple: Use devm_gpiod_get_optional()Alexandre Courbot1-7/+5
Use the new devm_gpiod_get_optional() to simplify the probe code. Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-08-06drm/panel: simple: Add AUO B133HTN01 panel supportAjay Kumar1-0/+30
The AUO B133HTN01 is a 13.6" FHD TFT LCD panel connecting to an eDP interface and with an integrated LED backlight unit. This panel is used on the Samsung Chromebook 2 (XE503C32). Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-08-06drm/panel: simple: Support delays in panel functionsAjay Kumar1-0/+30
For most of the panels, we need to provide delays during various stages of panel power up and power down. Add a structure to hold those delay values and use them in corresponding functions. Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-08-06drm/panel: simple: Add proper definition for prepare and unprepareAjay Kumar1-10/+27
Move out code from enable and disable routines to prepare and unprepare routines, so that functionality is properly distributed across all the panel functions. Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-08-06drm/panel: simple: Add dummy prepare and unprepare routinesAjay Kumar1-0/+12
This patch adds dummy definition for prepare and unprepare routines to simple panel driver. Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-08-06drm/panel: simple: Remove simple-panel compatibleThierry Reding1-2/+0
simple-panel is not a valid panel model, so there is no data (video timings, etc.) associated with it. Therefore drivers can't do anything useful with it, so it should not appear in the table of OF matches. Device trees will always need to specify the exact model of the panel. Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-08-06drm/panel: simple: Add Innolux N116BGE panel supportThierry Reding1-0/+27
The Innolux N116BGE is an 11.6" WXGA TFT LCD panel connecting to an eDP interface and with an integrated LED backlight unit. It is used in the Tegra132 Norrin reference design. Signed-off-by: Thierry Reding <treding@nvidia.com>
Powered by cgit, Gruvboxed by Blaster4385.