| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Instead of 'guessing' based on aliases of the status of the DSS drivers,
use the new interface to check that all needed drivers are loaded.
In this way we can be sure that all needed drivers are loaded so it is
safe to continue the probing of omapdrm.
This method will allow the omapdrm to be probed 'headless', without
outputs.
Signed-off-by: Peter Ujfalusi <[email protected]>
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
When omapdss is loaded (all core components are in place) create a list of
devices used in the display graph. This list later can be used by omapdrm
via the omapdss_stack_is_ready() function to check that these components
are loaded. Based on this information, omapdrm can defer probe in case when
the omapdss stack is not ready yet.
Signed-off-by: Peter Ujfalusi <[email protected]>
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
The functions can be used to check a component (by it's of_node) if it is
part of the omapdss display or output list. If the component is found, it
means that the driver is loaded.
Signed-off-by: Peter Ujfalusi <[email protected]>
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
DSS uses "replication logic" to convert color components from smaller
bit widths to bigger bit widths. Without replication logic, the color
component would be shifted and the least significant bits would be left
at 0, whereas with replication logic, the least significat bits will be
filled with the most significant bit.
For some reason omapdrm leaves replication logic always to off, which,
in the most common case, means that showing 16-bit RGB colors on 24-bit
display gives a bit darker colors than expected.
The reset value of the replication logic bit is enabled, and it should
always be set, as there's no practical reason to disable it. This patch
removes the option to disable it from omapdrm, and always sets it to
enabled in dispc.
Signed-off-by: Tomi Valkeinen <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
|
|
Remove two unused WB functions.
Signed-off-by: Tomi Valkeinen <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
|
|
omapdrm now uses dispc_ops instead of direct function calls so we can
remove all EXPORT_SYMBOLs from dispc. Most of the functions can also be
made static, but a few are used outside dispc.c.
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
Change omapdrm to get dispc_ops and use that to call the dispc functions
instead or direct function calls.
The change is very straightforward.
The only problem was in omap_crtc_init() which calls pipe2vbl(crtc), and
at that point of time the crtc->dev link, which is used to get the
dispc_ops, has not been set up yet. This patch makes omap_crtc_init()
skip the call to pipe2vbl() and instead calls
dispc_ops->mgr_get_vsync_irq() directly.
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
This patch changes the current omapdss driver to fill a dispc_ops struct
and set it to omapdss-base.
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
We want to change the dispc API from plain functions to a struct with
functions pointers, so that omapdrm can call either omapdss or omapdss6
depending on the platform.
This patch adds 'struct dispc_ops' and adds functions to omapdss-base
to set and get the ops.
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
omapdrm still uses a few non-dispc functions: dss_feat_get_num_mgrs(),
dss_feat_get_num_ovls() and dss_feat_get_supported_color_modes(). We
want to provide omapdrm a single dispc_ops function pointer struct so
that omapdrm will use either the current omapdss or the new omapdss6
driver depending on the platform.
Those three functions are really dispc functions, but are located in the
dss_features.c for legacy reasons.
This patch adds similar functionss to the dispc, and changes omapdrm to
use those new functions. Underneath the functions still call the
functions from dss_feature.c.
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
This patch moves the common parts of omapdss to omapdss-base so that
both the current omapdss driver and the new omapdss6 driver can use
them.
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
display.c uses dsi_get_pixel_size() which is implemented in the DSI
driver, and we won't have that in the omapdss-base module, to which we
want to move display.c
This patch changes display.c not to use dsi_get_pixel_size(). The call
can be replaced with a simple check for OMAP_DSS_DSI_FMT_RGB565.
We can also make dsi_get_pixel_size() static as it's no longer used
outside dsi.c.
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
We don't have omapdss's custom error printing functions in the common
omapdss-base module, to which we want to move output.c.
This patch changes output.c to use dev_err instead of DSSERR so that it
doesn't depend on DSSERR.
Signed-off-by: Tomi Valkeinen <[email protected]>
Acked-by: Laurent Pinchart <[email protected]>
|
|
omapdss_is_initialized() is used to find out if omapdss has been probed
successfully. This patch moves the related code to the common
omapdss-base module, so that the same support will be there for both
omapdss and omapdss6.
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
We are working towards enabling omapdss6, which will consists of a new
dss, dispc and dpi drivers. omapdss6 will be a new module. The panel,
encoder and omapdrm will need to use either the current omapdss driver
or the new omapdss6 driver, depending on the platform.
This will be implemented with a common base module and function
pointers.
This patch adds a skeleton omapdss-base.ko module, to which we'll be
moving common dss functionality like registration of the panels.
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
While implementing writeback support, odd behavior of WBDELAYCOUNT was
observed with the combination of WB capture and HDMI. The result of the
debugging was that the HDMI sync polarities are not set correctly.
The current code sets the sync polarities going from HDMI WP to DISPC
according to the video mode used, which seems to work normally fine, but
causes problems with WB as WB expects the syncs to be active-high.
This patch changes the HDMI sync polarities so that the DISPC always
gets active-high syncs from HDMI WP, and the HDMI core gets sync
polarities according to the used video mode.
Signed-off-by: Tomi Valkeinen <[email protected]>
Acked-by: Laurent Pinchart <[email protected]>
|
|
Add support for render nodes in omap driver and allow required
ioctls to be accessible via render nodes.
This enables unprivileged clients to allocate resources like GEM buffers
for rendering their content into. Mode setting (KMS ioctls) is not
allowed using render nodes. These buffers are then shared with
a previleged process (e.g compositor) that has mode setting access.
An example of this use case is Android where the hardware composer is
the only master and has mode setting access. Every other client then
uses render node(e.g /dev/dri/renderD128 to allocate and use its buffers.
Signed-off-by: Hemant Hariyani <[email protected]>
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
The clock source selection for the LCD outputs is too hardcoded at the
moment. For example, LCD3 is set to use PLL2_1, and PLL2 doesn't exist
on DRA72x SoCs.
There are quite many ways to configure the clocks, even using HDMI PLL
for LCD outputs, but enabling full configuration of the clocks is rather
tricky.
This patch improves the situation a bit by checking if the PLL about to
be used exists, and if not, tries another one.
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
mode_config's min_width and min_height are both set to 32, which is
overly restrictive.
The real limits depend on whether we're configuring a crtc or a plane,
but a limit of 8x2 is safe for both cases.
Signed-off-by: Tomi Valkeinen <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
|
|
The driver only uses even dividers for hsdiv when pclk >= 100MHz, as odd
dividers can create uneven duty cycle. However, while this holds true
for some dividers like DISPC's LCK and PCK dividers, it is not actually
true for hsdiv.
hsdiv always produces even duty cycle, so the constraint can be removed.
Signed-off-by: Tomi Valkeinen <[email protected]>
Acked-by: Laurent Pinchart <[email protected]>
|
|
The current driver doesn't expose any of the CRTC HW properties like
background color or transparency key, and sets them at CRTC enable time.
Refactor this into a separate function and call that function from
omap_crtc_atomic_flush(). This is the behavior we want when the
properties can be configured, so this patch makes it easier to add
patches later which implement those properties.
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
DRA7 errata i886 (FPDLink PLL Unlocks With Certain SoC PLL M/N Values)
says that FPDLink is sensitive to jitter on the vout clock, and that low
PLL M and N values result in more jitter than high M and N values.
This patch implements a workaround for the problem by changing the PLL
setup to search for clocks starting from high M and N values, instead of
low values. This should not cause any functional change, and only
reduces the jitter.
Signed-off-by: Tomi Valkeinen <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
|
|
Linux 4.11-rc3 as requested by Daniel
|
|
omap_gem_dmabuf_mmap() returns an error (with a WARN) when called for a
buffer which is allocated with dma_alloc_*(). This prevents dmabuf mmap
from working on SoCs without DMM, e.g. AM4 and OMAP3.
I could not find any reason for omap_gem_dmabuf_mmap() rejecting such
buffers, and just removing the if() fixes the limitation.
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-next
First slice of drm-misc-next for 4.12:
Core/subsystem-wide:
- link status core patch from Manasi, for signalling link train fail
to userspace. I also had the i915 patch in here, but that had a
small buglet in our CI, so reverted.
- more debugfs_remove removal from Noralf, almost there now (Noralf
said he'll try to follow up with the stragglers).
- drm todo moved into kerneldoc, for better visibility (see
Documentation/gpu/todo.rst), lots of starter tasks in there.
- devm_ of helpers + use it in sti (from Ben Gaignard, acked by Rob
Herring)
- extended framebuffer fbdev support (for fbdev flipping), and vblank
wait ioctl fbdev support (Maxime Ripard)
- misc small things all over, as usual
- add vblank callbacks to drm_crtc_funcs, plus make lots of good use
of this to simplify drivers (Shawn Guo)
- new atomic iterator macros to unconfuse old vs. new state
Small drivers:
- vc4 improvements from Eric
- vc4 kerneldocs (Eric)!
- tons of improvements for dw-mipi-dsi in rockchip from John Keeping
and Chris Zhong.
- MAINTAINERS entries for drivers managed in drm-misc. It's not yet
official, still an experiment, but definitely not complete fail and
better to avoid confusion. We kinda screwed that up with drm-misc a
bit when we started committers last year.
- qxl atomic conversion (Gabriel Krisman)
- bunch of virtual driver polish (qxl, virgl, ...)
- misc tiny patches all over
This is the first time we've done the same merge-window blackout for
drm-misc as we've done for drm-intel for ages, hence why we have a
_lot_ of stuff queued already. But it's still only half of drm-intel
(room to grow!), and the drivers in drm-misc experiment seems to work
at least insofar as that you also get lots of driver updates here
alredy.
* tag 'drm-misc-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-misc: (141 commits)
drm/vc4: Fix OOPSes from trying to cache a partially constructed BO.
drm/vc4: Fulfill user BO creation requests from the kernel BO cache.
Revert "drm/i915: Implement Link Rate fallback on Link training failure"
drm/fb-helper: implement ioctl FBIO_WAITFORVSYNC
drm: Update drm_fbdev_cma_init documentation
drm/rockchip/dsi: add dw-mipi power domain support
drm/rockchip/dsi: fix insufficient bandwidth of some panel
dt-bindings: add power domain node for dw-mipi-rockchip
drm/rockchip/dsi: remove mode_valid function
drm/rockchip/dsi: dw-mipi: correct the coding style
drm/rockchip/dsi: dw-mipi: support RK3399 mipi dsi
dt-bindings: add rk3399 support for dw-mipi-rockchip
drm/rockchip: dw-mipi-dsi: add reset control
drm/rockchip: dw-mipi-dsi: support non-burst modes
drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
drm/rockchip: vop: test for P{H,V}SYNC
drm/rockchip: dw-mipi-dsi: use positive check for N{H, V}SYNC
drm/rockchip: dw-mipi-dsi: use specific poll helper
drm/rockchip: dw-mipi-dsi: improve PLL configuration
drm/rockchip: dw-mipi-dsi: properly configure PHY timing
...
|
|
<linux/sched.h> into <linux/sched/signal.h>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <[email protected]>
Cc: Mike Galbraith <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Use a more common logging style.
Miscellanea:
o Coalesce formats and realign arguments
o Neaten a few macros now using pr_<level>
Signed-off-by: Joe Perches <[email protected]>
Acked-by: Rob Clark <[email protected]>
Acked-by: Sinclair Yeh <[email protected]>
Acked-by: Patrik Jakobsson <[email protected]>
Acked-by: Tomi Valkeinen <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
Link: http://patchwork.freedesktop.org/patch/msgid/76355db47b31668bb64d996865ceee53bd66b11f.1488285953.git.joe@perches.com
|
|
Backmerge the main pull request to sync up with all the newly landed
drivers. Otherwise we'll have chaos even before 4.12 started in
earnest.
Signed-off-by: Daniel Vetter <[email protected]>
|
|
->fault(), ->page_mkwrite(), and ->pfn_mkwrite() calls do not need to
take a vma and vmf parameter when the vma already resides in vmf.
Remove the vma parameter to simplify things.
[[email protected]: fix ARM build]
Link: http://lkml.kernel.org/r/[email protected]
Link: http://lkml.kernel.org/r/148521301778.19116.10840599906674778980.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
Reviewed-by: Ross Zwisler <[email protected]>
Cc: Theodore Ts'o <[email protected]>
Cc: Darrick J. Wong <[email protected]>
Cc: Matthew Wilcox <[email protected]>
Cc: Dave Hansen <[email protected]>
Cc: Christoph Hellwig <[email protected]>
Cc: Jan Kara <[email protected]>
Cc: Dan Williams <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.11.
Nothing too major, the tinydrm and mmu-less support should make
writing smaller drivers easier for some of the simpler platforms, and
there are a bunch of documentation updates.
Intel grew displayport MST audio support which is hopefully useful to
people, and FBC is on by default for GEN9+ (so people know where to
look for regressions). AMDGPU has a lot of fixes that would like new
firmware files installed for some GPUs.
Other than that it's pretty scattered all over.
I may have a follow up pull request as I know BenH has a bunch of AST
rework and fixes and I'd like to get those in once they've been tested
by AST, and I've got at least one pull request I'm just trying to get
the author to fix up.
Core:
- drm_mm reworked
- Connector list locking and iterators
- Documentation updates
- Format handling rework
- MMU-less support for fbdev helpers
- drm_crtc_from_index helper
- Core CRC API
- Remove drm_framebuffer_unregister_private
- Debugfs cleanup
- EDID/Infoframe fixes
- Release callback
- Tinydrm support (smaller drivers for simple hw)
panel:
- Add support for some new simple panels
i915:
- FBC by default for gen9+
- Shared dpll cleanups and docs
- GEN8 powerdomain cleanup
- DMC support on GLK
- DP MST audio support
- HuC loading support
- GVT init ordering fixes
- GVT IOMMU workaround fix
amdgpu/radeon:
- Power/clockgating improvements
- Preliminary SR-IOV support
- TTM buffer priority and eviction fixes
- SI DPM quirks removed due to firmware fixes
- Powerplay improvements
- VCE/UVD powergating fixes
- Cleanup SI GFX code to match CI/VI
- Support for > 2 displays on 3/5 crtc asics
- SI headless fixes
nouveau:
- Rework securre boot code in prep for GP10x secure boot
- Channel recovery improvements
- Initial power budget code
- MMU rework preperation
vmwgfx:
- Bunch of fixes and cleanups
exynos:
- Runtime PM support for MIC driver
- Cleanups to use atomic helpers
- UHD Support for TM2/TM2E boards
- Trigger mode fix for Rinato board
etnaviv:
- Shader performance fix
- Command stream validator fixes
- Command buffer suballocator
rockchip:
- CDN DisplayPort support
- IOMMU support for arm64 platform
imx-drm:
- Fix i.MX5 TV encoder probing
- Remove lower fb size limits
msm:
- Support for HW cursor on MDP5 devices
- DSI encoder cleanup
- GPU DT bindings cleanup
sti:
- stih410 cleanups
- Create fbdev at binding
- HQVDP fixes
- Remove stih416 chip functionality
- DVI/HDMI mode selection fixes
- FPS statistic reporting
omapdrm:
- IRQ code cleanup
dwi-hdmi bridge:
- Cleanups and fixes
adv-bridge:
- Updates for nexus
sii8520 bridge:
- Add interlace mode support
- Rework HDMI and lots of fixes
qxl:
- probing/teardown cleanups
ZTE drm:
- HDMI audio via SPDIF interface
- Video Layer overlay plane support
- Add TV encoder output device
atmel-hlcdc:
- Rework fbdev creation logic
tegra:
- OF node fix
fsl-dcu:
- Minor fixes
mali-dp:
- Assorted fixes
sunxi:
- Minor fix"
[ This was the "fixed" pull, that still had build warnings due to people
not even having build tested the result. I'm not a happy camper
I've fixed the things I noticed up in this merge. - Linus ]
* tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux: (1177 commits)
lib/Kconfig: make PRIME_NUMBERS not user selectable
drm/tinydrm: helpers: Properly fix backlight dependency
drm/tinydrm: mipi-dbi: Fix field width specifier warning
drm/tinydrm: mipi-dbi: Silence: ‘cmd’ may be used uninitialized
drm/sti: fix build warnings in sti_drv.c and sti_vtg.c files
drm/amd/powerplay: fix PSI feature on Polars12
drm/amdgpu: refuse to reserve io mem for split VRAM buffers
drm/ttm: fix use-after-free races in vm fault handling
drm/tinydrm: Add support for Multi-Inno MI0283QT display
dt-bindings: Add Multi-Inno MI0283QT binding
dt-bindings: display/panel: Add common rotation property
of: Add vendor prefix for Multi-Inno
drm/tinydrm: Add MIPI DBI support
drm/tinydrm: Add helper functions
drm: Add DRM support for tiny LCD displays
drm/amd/amdgpu: post card if there is real hw resetting performed
drm/nouveau/tmr: provide backtrace when a timeout is hit
drm/nouveau/pci/g92: Fix rearm
drm/nouveau/drm/therm/fan: add a fallback if no fan control is specified in the vbios
drm/nouveau/hwmon: expose power_max and power_crit
..
|
|
Let's disable all scaling that requires horizontal decimation with
higher factor than 4, until we have better estimates of what we can
and can not do. However, NV12 color format appears to work Ok with
all decimation factors.
When decimating horizontally by more that 4 the dss is not able to
fetch the data in burst mode. When this happens it is hard to tell if
there enough bandwidth. Despite what theory says this appears to be
true also for 16-bit color formats.
Signed-off-by: Jyri Sarha <[email protected]>
Acked-by: Laurent Pinchart <[email protected]>
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
Move drm_atomic_helper_commit_modeset_enables() call to before
drm_atomic_helper_commit_planes() call and have a
omap_atomic_wait_for_completion() call after both.
With the current dss dispc implementation we have to enable the new
modeset before we can commit planes. The dispc ovl configuration
relies on the video mode configuration been written into the HW when
the ovl configuration is calculated.
This approach is not ideal because after a mode change the plane
update is executed only after the first vblank interrupt. The dispc
implementation should be fixed so that it is able use uncommitted drm
state information. information.
Signed-off-by: Jyri Sarha <[email protected]>
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
This reverts commit dadf4659d0608e034b6633f30300c2eff2dafb4c.
If planes are not disabled when the they are not on any crtc anymore
they will remain active and may show as "ghosts" when the crtc they
were last on is active again.
Signed-off-by: Jyri Sarha <[email protected]>
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
The vblank hooks in struct drm_driver are deprecated and only meant for
legacy drivers. For modern drivers with DRIVER_MODESET flag, the hooks
in struct drm_crtc_funcs should be used instead.
Signed-off-by: Tomi Valkeinen <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
|
|
Core code already makes drm_driver.get_vblank_counter hook optional by
letting drm_vblank_no_hw_counter be the default implementation for the
function hook. So the drm_vblank_no_hw_counter assignment in the driver
code becomes redundant and can be removed now.
Signed-off-by: Shawn Guo <[email protected]>
Cc: Alexey Brodkin <[email protected]>
Cc: Liviu Dudau <[email protected]>
Cc: Mali DP Maintainers <[email protected]>
Cc: Russell King <[email protected]>
Cc: Boris Brezillon <[email protected]>
Cc: Inki Dae <[email protected]>
Cc: Stefan Agner <[email protected]>
Cc: Xinliang Liu <[email protected]>
Cc: Daniel Vetter <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: CK Hu <[email protected]>
Cc: Neil Armstrong <[email protected]>
Cc: Rob Clark <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Ben Skeggs <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Mark Yao <[email protected]>
Cc: Benjamin Gaignard <[email protected]>
Cc: Maxime Ripard <[email protected]>
Cc: Jyri Sarha <[email protected]>
Cc: Eric Anholt <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
Acked-by: Boris Brezillon <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Acked-by: Russell King <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Acked-by: Alexey Brodkin <[email protected]>
Acked-by: Liviu Dudau <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
Link: http://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Noticed that everyone duplicates the same logic here and we could safe
a few lines per driver. Yay for lots of drivers to make such tiny
refactors worth-while!
v2: Forgot to git add everything :(
v3: Actually remove release_fbi (Sean, Emil, Chris) ...
Cc: Chris Wilson <[email protected]>
Cc: Sean Paul <[email protected]>
Cc: Noralf Trønnes <[email protected]>
Cc: Emil Velikov <[email protected]>
Reviewed-by: Sean Paul <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
Link: http://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Instead of receiving the num_crts as a parameter, we can read it
directly from the mode_config structure. I audited the drivers that
invoke this helper and I believe all of them initialize the mode_config
struct accordingly, prior to calling the fb_helper.
I used the following coccinelle hack to make this transformation, except
for the function headers and comment updates. The first and second
rules are split because I couldn't find a way to remove the unused
temporary variables at the same time I removed the parameter.
// <smpl>
@r@
expression A,B,D,E;
identifier C;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
expression A,B,C,D,E;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
identifier r.C;
type T;
expression V;
@@
- T C;
<...
when != C
- C = V;
...>
// </smpl>
Changes since v1:
- Rebased on top of the tip of drm-misc-next.
- Remove mention to sti since a proper fix got merged.
Suggested-by: Daniel Vetter <[email protected]>
Signed-off-by: Gabriel Krisman Bertazi <[email protected]>
Reviewed-by: Eric Anholt <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
Link: http://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-next
Another round of -misc stuff:
- Noralf debugfs cleanup cleanup (not yet everything, some more driver
patches awaiting acks).
- More doc work.
- edid/infoframe fixes from Ville.
- misc 1-patch fixes all over, as usual
Noralf needs this for his tinydrm pull request.
* tag 'drm-misc-next-2017-01-30' of git://anongit.freedesktop.org/git/drm-misc: (48 commits)
drm/vc4: Remove vc4_debugfs_cleanup()
dma/fence: Export enable-signaling tracepoint for emission by drivers
drm/tilcdc: Remove tilcdc_debugfs_cleanup()
drm/tegra: Remove tegra_debugfs_cleanup()
drm/sti: Remove drm_debugfs_remove_files() calls
drm/radeon: Remove drm_debugfs_remove_files() call
drm/omap: Remove omap_debugfs_cleanup()
drm/hdlcd: Remove hdlcd_debugfs_cleanup()
drm/etnaviv: Remove etnaviv_debugfs_cleanup()
drm/etnaviv: allow build with COMPILE_TEST
drm/amd/amdgpu: Remove drm_debugfs_remove_files() call
drm/prime: Clarify DMA-BUF/GEM Object lifetime
drm/ttm: Make sure BOs being swapped out are cacheable
drm/atomic: Remove drm_atomic_debugfs_cleanup()
drm: drm_minor_register(): Clean up debugfs on failure
drm: debugfs: Remove all files automatically on cleanup
drm/fourcc: add vivante tiled layout format modifiers
drm/edid: Set YQ bits in the AVI infoframe according to CEA-861-F
drm/edid: Set AVI infoframe Q even when QS=0
drm/edid: Introduce drm_hdmi_avi_infoframe_quant_range()
...
|
|
drm_debugfs_cleanup() now removes all minor->debugfs_list entries
automatically, so the drm_driver.debugfs_cleanup callback is not
needed.
Cc: [email protected]
Signed-off-by: Noralf Trønnes <[email protected]>
Reviewed-by: Tomi Valkeinen <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
Link: http://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-next
- cleanups&fixes for dw-hdmi bride driver (Laurent)
- updates for adv bridge driver (John Stultz) for nexus
- drm_crtc_from_index helper rollout (Shawn Guo)
- removing drm_framebuffer_unregister_private from drivers&core
- target_vblank (Andrey Grodzovsky)
- misc tiny stuff
* tag 'drm-misc-next-2017-01-23' of git://anongit.freedesktop.org/git/drm-misc: (49 commits)
drm: qxl: Open code teardown function for qxl
drm: qxl: Open code probing sequence for qxl
drm/bridge: adv7511: Re-write the i2c address before EDID probing
drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID
drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be reused internally
drm/bridge: adv7511: Enable HPD interrupts to support hotplug and improve monitor detection
drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event()
drm/bridge: adv7511: Use work_struct to defer hotplug handing to out of irq context
drm: vc4: use crtc helper drm_crtc_from_index()
drm: tegra: use crtc helper drm_crtc_from_index()
drm: nouveau: use crtc helper drm_crtc_from_index()
drm: mediatek: use crtc helper drm_crtc_from_index()
drm: kirin: use crtc helper drm_crtc_from_index()
drm: exynos: use crtc helper drm_crtc_from_index()
dt-bindings: display: dw-hdmi: Clean up DT bindings documentation
drm: bridge: dw-hdmi: Assert SVSRET before resetting the PHY
drm: bridge: dw-hdmi: Fix the name of the PHY reset macros
drm: bridge: dw-hdmi: Define and use macros for PHY register addresses
drm: bridge: dw-hdmi: Detect PHY type at runtime
drm: bridge: dw-hdmi: Handle overflow workaround based on device version
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-next
omapdrm changes for 4.11
The main change here is the IRQ code cleanup, which gives us properly working
vblank counts and timestamps. We also get much less calls to runtime PM gets &
puts.
* tag 'omapdrm-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (26 commits)
drm/omap: panel-sony-acx565akm.c: Add MODULE_ALIAS
drm/omap: dsi: fix compile errors when enabling debug prints
drm: omapdrm: Perform initialization/cleanup at probe/remove time
drm: Move vblank cleanup from unregister to release
drm: omapdrm: Use sizeof(*var) instead of sizeof(type) for structures
drm: omapdrm: Remove global variables
drm: omapdrm: Simplify IRQ wait implementation
drm: omapdrm: Inline the pipe2vbl function
drm: omapdrm: Don't call DISPC power handling in IRQ wait functions
drm: omapdrm: Remove unused parameter from omap_drm_irq handler
drm: omapdrm: Don't expose the omap_irq_(un)register() functions
drm: omapdrm: Keep vblank interrupt enabled while CRTC is active
drm: omapdrm: Use a spinlock to protect the CRTC pending flag
drm: omapdrm: Prevent processing the same event multiple times
drm: omapdrm: Check the CRTC software state at enable/disable time
drm: omapdrm: Let the DRM core skip plane commit on inactive CRTCs
drm: omapdrm: Replace DSS manager state check with omapdrm CRTC state
drm: omapdrm: Handle OCP error IRQ directly
drm: omapdrm: Handle CRTC error IRQs directly
drm: omapdrm: Handle FIFO underflow IRQs internally
...
|
|
Since we need to change the implementation, stop exposing internals.
Provide kref_read() to read the current reference count; typically
used for debug messages.
Kills two anti-patterns:
atomic_read(&kref->refcount)
kref->refcount.counter
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Cc: Andrew Morton <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Paul E. McKenney <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
This is the deprecated function for when you embedded the framebuffer
somewhere else (which breaks refcounting). But omapdrm is using
drm_framebuffer_remove and a free-standing fb, so this is rendundant.
Cc: Tomi Valkeinen <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
Link: http://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-next
Back to regular -misc pulls with reasonable sizes:
- dma_fence error clarification (Chris)
- drm_crtc_from_index helper (Shawn), pile more patches on the m-l to roll
this out to drivers
- mmu-less support for fbdev helpers from Benjamin
- piles of kerneldoc work
- some polish for crc support from Tomeu and Benjamin
- odd misc stuff all over
* tag 'drm-misc-next-2017-01-09' of git://anongit.freedesktop.org/git/drm-misc: (48 commits)
dma-fence: Introduce drm_fence_set_error() helper
dma-fence: Wrap querying the fence->status
dma-fence: Clear fence->status during dma_fence_init()
drm: fix compilations issues introduced by "drm: allow to use mmuless SoC"
drm: Change the return type of the unload hook to void
drm: add more document for drm_crtc_from_index()
drm: remove useless parameters from drm_pick_cmdline_mode function
drm: crc: Call wake_up_interruptible() each time there is a new CRC entry
drm: allow to use mmuless SoC
drm: compile drm_vm.c only when needed
fbmem: add a default get_fb_unmapped_area function
drm: crc: Wait for a frame before returning from open()
drm: Move locking into drm_debugfs_crtc_crc_add
drm/imx: imx-tve: Remove unused variable
Revert "drm: nouveau: fix build when LEDS_CLASS=m"
drm: Add kernel-doc for drm_crtc_commit_get/put
drm/atomic: Fix outdated comment.
drm: reference count event->completion
gpu: drm: mgag200: mgag200_main:- Handle error from pci_iomap
drm: Document deprecated load/unload hook
...
|
|
The integer returned by the unload hook is ignored by the drm core, so
let's make it void.
This patch was created using the following Coccinelle semantic script
(except for the declaration and comment in drm_drv.h):
Compile-tested only.
// <smpl>
@ get_name @
struct drm_driver drv;
identifier fn;
@@
drv.unload = fn;
@ replace_type @
identifier get_name.fn;
@@
- int
+ void
fn (...)
{
...
}
@ remove_return_param @
identifier get_name.fn;
@@
void fn (...)
{
<...
if (...)
return
- ...
;
...>
}
@ drop_final_return @
identifier get_name.fn;
@@
void fn (...)
{
...
- return 0;
}
// </smpl>
Suggested-by: Daniel Vetter <[email protected]>
Signed-off-by: Gabriel Krisman Bertazi <[email protected]>
Acked-by: Christian König <[email protected]>.
Signed-off-by: Daniel Vetter <[email protected]>
Link: http://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-next
First -misc pull for 4.11:
- drm_mm rework + lots of selftests (Chris Wilson)
- new connector_list locking+iterators
- plenty of kerneldoc updates
- format handling rework from Ville
- atomic helper changes from Maarten for better plane corner-case handling
in drivers, plus the i915 legacy cursor patch that needs this
- bridge cleanup from Laurent
- plus plenty of small stuff all over
- also contains a merge of the 4.10 docs tree so that we could apply the
dma-buf kerneldoc patches
It's a lot more than usual, but due to the merge window blackout it also
covers about 4 weeks, so all in line again on a per-week basis. The more
annoying part with no pull request for 4 weeks is managing cross-tree
work. The -intel pull request I'll follow up with does conflict quite a
bit with -misc here. Longer-term (if drm-misc keeps growing) a
drm-next-queued to accept pull request for the next merge window during
this time might be useful.
I'd also like to backmerge -rc2+this into drm-intel next week, we have
quite a pile of patches waiting for the stuff in here.
* tag 'drm-misc-next-2016-12-30' of git://anongit.freedesktop.org/git/drm-misc: (126 commits)
drm: Add kerneldoc markup for new @scan parameters in drm_mm
drm/mm: Document locking rules
drm: Use drm_mm_insert_node_in_range_generic() for everyone
drm: Apply range restriction after color adjustment when allocation
drm: Wrap drm_mm_node.hole_follows
drm: Apply tight eviction scanning to color_adjust
drm: Simplify drm_mm scan-list manipulation
drm: Optimise power-of-two alignments in drm_mm_scan_add_block()
drm: Compute tight evictions for drm_mm_scan
drm: Fix application of color vs range restriction when scanning drm_mm
drm: Unconditionally do the range check in drm_mm_scan_add_block()
drm: Rename prev_node to hole in drm_mm_scan_add_block()
drm: Fix O= out-of-tree builds for selftests
drm: Extract struct drm_mm_scan from struct drm_mm
drm: Add asserts to catch overflow in drm_mm_init() and drm_mm_init_scan()
drm: Simplify drm_mm_clean()
drm: Detect overflow in drm_mm_reserve_node()
drm: Fix kerneldoc for drm_mm_scan_remove_block()
drm: Promote drm_mm alignment to u64
drm: kselftest for drm_mm and restricted color eviction
...
|
|
Add module alias for Sony ACX565AKM LCD panel. This makes it probe on Nokia
N900 when panel driver is built as a module.
Signed-off-by: Jarkko Nikula <[email protected]>
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
dsi.c compile fails if PRINT_VERBOSE_VM_TIMINGS is enabled, as the
video timings were not converted in the code behind that ifdef. Note
that PRINT_VERBOSE_VM_TIMINGS has to be enabled by hand, there's no
config option for it.
Signed-off-by: H. Nikolaus Schaller <[email protected]>
Acked-by: Peter Ujfalusi <[email protected]>
[[email protected]: fixed the patch description]
Signed-off-by: Tomi Valkeinen <[email protected]>
|
|
Including all drivers. I thought about keeping small compat functions
to avoid having to change all drivers. But I really like the
drm_printer idea, so figured spreading it more widely is a good thing.
v2: Review from Chris:
- Natural argument order and better name for drm_mm_print.
- show_mm() macro in the selftest.
Cc: Rob Clark <[email protected]>
Cc: Russell King <[email protected]>
Cc: Alex Deucher <[email protected]>
Cc: Christian König <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Thierry Reding <[email protected]>
Cc: Jyri Sarha <[email protected]>
Reviewed-by: Chris Wilson <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
Link: http://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
The drm driver .load() operation is prone to race conditions as it
initializes the driver after registering the device nodes. Its usage is
deprecated, inline it in the probe function and call drm_dev_alloc() and
drm_dev_register() explicitly.
For consistency inline the .unload() handler in the remove function as
well.
Signed-off-by: Laurent Pinchart <[email protected]>
Reviewed-by: Tomi Valkeinen <[email protected]>
|