| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
align_pitch() uses ALIGN() to ensure the pitch is aligned to SGX's
requirement of 8 pixels. However, ALIGN() expects the alignment value to
be a power of two, which is not the case for 24 bits per pixels.
Use roundup() instead, which works for all alignments.
This fixes the error seen with 24 bits per pixel modes:
"buffer pitch (2176 bytes) is not a multiple of pixel size (3 bytes)"
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
If tiler_unpin() call in omap_gem_put_paddr() fails,
omap_gem_put_paddr() will immediately stop processing and return an
error.
This patch remoes that error checking, and also removes
omap_gem_put_paddr()'s return value, because:
* The caller of omap_gem_put_paddr() can do nothing if an error
happens, so it's pointless to return an error value
* If tiler_unpin() fails, the GEM object will possibly be left in an
undefined state, where the DMM mapping may have been removed, but the
GEM object still thinks everything is as it should be, leading to
crashes later.
* There's no point in returning an error from a "free" call, as the
caller can do nothing about it. So it's better to clean up as much as
possible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
omap_framebuffer_unpin() check the return value of omap_gem_put_paddr()
and return immediately if omap_gem_put_paddr() fails.
This patch removes the check for the return value, and also removes the
return value of omap_framebuffer_unpin(), because:
* Nothing checks the return value of omap_framebuffer_unpin(), and even
something did check it, there's nothing the caller can do to handle
the error.
* If a omap_gem_put_paddr() fails, the framebuffer's other planes will
be left unreleased. So it's better to call omap_gem_put_paddr() for
all the planes, even if one would fail.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Rework the crtc event/flip_wait system as follows:
- If we enable a crtc (full modeset), we set omap_crtc->pending and
register vblank irq.
- If we need to set GO bit (page flip), we do the same but also set the
GO bit.
- On vblank we unregister the irq, clear the 'pending' flag, send vblank
event to userspace if crtc->state->event != NULL, and wake up
'pending_wait' wq.
- In omap_atomic_complete() we wait for the 'pending' flag to get reset
for all enabled crtcs using 'pending_wait' wq.
The above ensures that we send the events to userspace in vblank, and
that after the wait in omap_atomic_complete() everything for the
affected crtcs has been completed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Planes setup is handled by the DRM core through the atomic helpers,
there's no need to duplicate the code in the CRTC .enable() and
.disable() operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Now that the driver is fully converted to atomic operations, and that
the atomic helpers call the operations in the right order, we can move
encoder setup to where it belongs, in the encoder operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
DRM page flip vblank events requested by page flips or atomic commits
are created by the DRM core and then passed to driver through CRTC
states (for atomic commit) or directly to the page flip handler (for
legacy page flips). The events are then kept aside until the page flip
completes, at which point drivers queue them for delivery with a call to
drm_send_vblank_event().
When a DRM file handle is closed events pending for delivery are cleaned
up automatically by the DRM core. Events that have been passed to the
driver but haven't completed yet, however, are not handled by the DRM
core. Drivers are responsible for destroying them and must not attempt
to queue them for delivery. This is usually handled by drivers'
preclose() handlers that cancel and destroy page flip events that
reference the file handle being closed.
With asynchronous atomic updates the story becomes more complex. Several
asynchronous atomic updates can be pending, each of them carrying
per-CRTC events. As the atomic_commit() operation doesn't receive a file
handle context, drivers can't know which file handle a pending update
refers to, making it difficult to cancel or wait for completion of
updates related to the file handle being closed.
It should be noted that cancelling page flips or waiting for atomic
updates completion isn't required by the DRM core when closing a file
handle. The only requirement is that no event gets queued for delivery
after the preclose() operation returns. This can easily be achieved by
storing events for atomic commits in a list, unlinking events from the
file handle being closed by setting the file_priv field to NULL, and
skipping delivery of unlinked events.
This logic replaces the page flip cancellation completely.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The function isn't used outside of its compilation unit, make it static.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The field tracks the plane state to avoid double-enable or -disable.
This isn't required anymore, as
- the DRM atomic core guarantees that the plane atomic_update and
atomic_disable functions will never be called on an enabled/disabled
plane
- the CRTC enable/disable operations that enable/disable the plane are
already guarded against double enable/disable
We can thus remove the enabled field completely. The
omap_plane_set_enable() function then becomes a wrapper around
omap_plane_setup() which can be called directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Allow setting up plane properties atomically using the plane
set_property atomic helper. The properties are now stored in the plane
state (requiring subclassing it) and applied when updating the planes.
The CRTC exposes the properties of its primary plane for legacy reason.
We can't get rid of that API, so simply delegate it to the primary
plane.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Since the removal of omap_plane_mode_set(), framebuffers are now pinned
exclusively through the plane .prepare_fb() and .cleanup_fb() operations
as the remaining callers of omap_plane_setup() don't modify the
framebuffer. Remove the manual pin/unpin infrastructure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The atomic page flip helper implements the page flip operation using
asynchronous commits.
As the legacy page flip was the last caller of omap_plane_mode_set(),
remove the function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Implement a custom .atomic_commit() handler that supports asynchronous
commits using a work queue. This can be used for userspace-driven
asynchronous commits, as well as for an atomic page flip implementation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Use the <...> include style instead of "..." for DRM headers and sort
the headers alphabetically to ease detection of duplicates.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Pending page flips must be cancelled when closing the device, otherwise
their completion at next vblank will result in nasty effects, including
possible oopses due to resources required to complete the page flip
being freed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The omapdrm can't use drm_irq_install() and drm_irq_uninstall() as it
delegates IRQ handling to the omapdss driver. However, the code still
declares IRQ-related operations used by the DRM IRQ helpers, and calls
them indirectly.
Simplify the implementation by calling the functions directly or
inlining them. The irq_enabled checks can then also be simplified as
the call stacks guarantees that omap_drm_irq_install() and
omap_drm_irq_uninstall() will never run concurrently.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The omapdrm driver implements a mechanism to apply new settings (due to
plane update, plane disable, plane property set, CRTC mode set or CRTC
DPMS) asynchronously. While this improves performance, it adds a level
of complexity that makes transition to the atomic update API close to
impossible. Furthermore the atomic update API requires part of the apply
operations to be synchronous (such as pinning the framebuffers), so the
current implementation needs to be changed.
Simplify the CRTC and plane code by making updates synchronous to
prepare for the switch to the atomic update API. Asynchronous update
will be implemented in a second step.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Rotation is a standard property, store it in
dev->mode_config.rotation_property. While at it, extract the properties
initialization code to a separate function instead of running it for
every plane.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
omap_gem_objects are added to dev->obj_list in omap_gem_new, and removed
in omap_gem_free_object. Unfortunately there's no locking for
dev->obj_list, which eventually leads to a crash:
WARNING: CPU: 1 PID: 1123 at lib/list_debug.c:59 __list_del_entry+0xa4/0xe0()
list_del corruption. prev->next should be e9281344, but was ea722b84
Add a spinlock to protect dev->obj_list.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The function will convert the Q16 source coordinates to integers, avoid
converting integers to Q16 first and perform the opposite conversion.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
All the manual update display code implements eventually ends up to just
calls to omap_connector_flush(), currently implemented as an empty TODO
stub. Remove it, the code can always be revived and implemented later if
interest in manual update displays becomes a reality.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The planes don't care about DPMS states, don't propagate it
unnecessarily to the plane functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Remove the CRTC private planes by switching to the universal plane API.
This results in a merge of the CRTC private plane created by the driver
(omap_crtc->plane) and the CRTC primary plane created by the DRM core
(crtc->primary).
Reference counting of the framebuffers in the update plane operation is
thus simplified as no reference needs to be stored in the private plane
anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
v2: Don't forget git add, noticed by David.
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- much better HDMI infoframe support for OMAP
- Cirrus Logic CLPS711X framebuffer driver
- DT support for PL11x CLCD driver
- various small fixes
* tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (35 commits)
OMAPDSS: DSI: fix depopulating dsi peripherals
video: hyperv: hyperv_fb: refresh the VM screen by force on VM panic
video: ARM CLCD: Fix DT-related build problems
drivers: video: fbdev: atmel_lcdfb.c: Add ability to inverted backlight PWM.
video: ARM CLCD: Add DT support
drm/omap: Add infoframe & dvi/hdmi mode support
OMAPDSS: HDMI: remove the unused code
OMAPDSS: HDMI5: add support to set infoframe & HDMI mode
OMAPDSS: HDMI4: add support to set infoframe & HDMI mode
OMAPDSS: HDMI: add infoframe and hdmi_dvi_mode fields
OMAPDSS: add hdmi ops to hdmi-connector and tpd12s015
OMAPDSS: add hdmi ops to hdmi_ops and omap_dss_driver
OMAPDSS: HDMI: remove custom avi infoframe
OMAPDSS: HDMI5: use common AVI infoframe support
OMAPDSS: HDMI4: use common AVI infoframe support
OMAPDSS: Kconfig: select HDMI
OMAPDSS: HDMI: fix name conflict
OMAPDSS: DISPC: clean up dispc_mgr_timings_ok
OMAPDSS: DISPC: reject interlace for lcd out
OMAPDSS: DISPC: fix debugfs reg dump
...
|
|
The rotation property stuff should be standardized among all drivers.
Move the bits to drm_crtc.h from omap_drv.h.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Make the omapdrm driver use the new HDMI ops when possible.
omapdrm will call set_hdmi_mode (when available) to tell the encoder
driver whether the monitor is a DVI or HDMI monitor, and if it's an HDMI
monitor, omapdrm will call set_hdmi_infoframe to to set the AVI
infoframe.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Rob Clark <robdclark@gmail.com>
|
|
At module unload, omap_fbdev_free() gets called which releases the
framebuffers. However, the framebuffers are still used by crtcs, and
will be released only later at vsync. The driver doesn't wait for this,
and goes on to release the rest of the resources, which often
causes a crash.
This patchs adds a omap_crtc_flush() function which waits until the crtc
has finished with its apply queue and page flips.
The function utilizes a simple polling while-loop, as the performance is
not an issue here.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-next
omapdrm patches for 3.14
* tag 'omapdrm-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
drm/omap: Enable DT support for DMM
drm/omap: fix: change dev_unload order
drm/omap: fix: disable encoder before destroying it
drm/omap: fix: disconnect devices when omapdrm module is removed
drm/omap: fix: Defer probe if an omapdss device requests for it at connect
drm/omap: fix (un)registering irqs inside an irq handler
Conflicts:
drivers/gpu/drm/omapdrm/omap_drv.c
|
|
With the omapdss device model changes. omapdrm is required to call dssdriver's
connect() op to register a panel. This is currently done in omap_modeset_init()
A call to connect() can fail if the omapdss panels or the encoders(HDMI/DPI)
they connect to have some resource(like regulators, I2C adapter) missing. If
this happens, the correct approach is to defer omapdrm's probe.
omapdrm currently ignores those panels which return a non zero value when
connected. This could result in omapdrm ignoring all panels on an omap board.
The right approach would be for omapdrm to request for probe deferral when a
panel's connect op returns -EPROBE_DEFER.
In order to do this, we need to call connect() much earlier during omapdrm's
probe to prevent too many things are already done by then. We now connect the
panels during pdev_probe(), before anything else is initialized, so that we
don't need to undo too many things if a defer was requested.
Now when we enter omap_modeset_init(), we have a set of panels that have been
connected. We now proceed with registering only those panels that are already
connected.
A special case has to be considered when no panels are available to connect when
omapdrm probes. In this case too, we defer probe and expect that a panel will be
available to connect the next time.
Checking whether the panel has a driver or whether it has get_timing/read_edid
ops in omap_modeset_init() are redundant with the new display model. These can
be removed since a dssdev device will always have a driver associated with it,
and all dssdev drivers have a get_timings op.
This will mainly fix cases when omapdrm is built-in the kernel, since that's
generally where resources like regulators or I2C are unavailable because of
probe order dependencies.
In particular this fixes boot with omapdrm built-in on an omap4 panda ES board.
The regulators used by HDMI(provided by I2C based TWL regulators) aren't
initialized because I2C isn't initialized, I2C isn't initialized as it's pins
are not configured because pinctrl is yet to probe.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
omapdrm (un)registers irqs inside an irq handler. The problem is that
the (un)register function uses dispc_runtime_get/put() to enable the
clocks, and those functions are not irq safe by default.
This was kind of fixed in 48664b21aeeffb40c5fa06843f18052e2c4ec9ef
(OMAPDSS: DISPC: set irq_safe for runtime PM), which makes dispc's
runtime calls irq-safe.
However, using pm_runtime_irq_safe in dispc makes the parent of dispc,
dss, always enabled, effectively preventing PM for the whole DSS module.
This patch makes omapdrm behave better by adding new irq (un)register
functions that do not use dispc_runtime_get/put, and using those
functions in interrupt context. Thus we can make dispc again
non-irq-safe, allowing proper PM.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Rob Clark <robdclark@gmail.com>
|
|
I've killed them a long time ago in drm/i915, let's get rid of this
remnant of shared drm core days for good.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
All drivers embed gem-objects into their own buffer objects. There is no
reason to keep drm_gem_object_alloc(), gem->driver_private and
->gem_init_object() anymore.
New drivers are highly encouraged to do the same. There is no benefit in
allocating gem-objects separately.
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
And simplify how we hold a ref+pin to what is being scanned out by using
fb refcnt'ing. The previous logic pre-dated fb refcnt, and as a result
was less straightforward than it could have been. By holding a ref to
the fb, we don't have to care about how many plane's there are and
holding a ref to each color plane's bo.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
All the gem based kms drivers really want the same function to
destroy a dumb framebuffer backing storage object.
So give it to them and roll it out in all drivers.
This still leaves the option open for kms drivers which don't use GEM
for backing storage, but it does decently simplify matters for gem
drivers.
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Cc: Ben Skeggs <skeggsb@gmail.com>
Reviwed-by: Rob Clark <robdclark@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Currently omapdrm creates crtcs, which map directly to DSS overlay
managers, only on demand at init time. This would make it difficult to
manage connecting the display entities in the future, as the code cannot
just search for a suitable overlay manager.
We cannot fix this the sane way, which would be to create crtcs for each
overlay manager, because we need an overlay for each crtc. With limited
number of overlays, that's not possible.
So the solution for now is to detach the overlay manager from the crtc.
crtcs are still created on demand at init time, but all overlay managers
are always initialized by the omapdss.
This way we can create and connect whole display pipelines from the
overlay manager to the display, regardless of which crtcs omapdrm would
create.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The omapdrm driver currently takes a config/module arg to figure out the number
of crtcs it needs to create. We could create as many crtcs as there are overlay
managers in the DSS hardware, but we don't do that because each crtc eats up
one DSS overlay, and that reduces the number of planes we can attach to a single
crtc.
Since the number of crtcs may be lesser than the number of hardware overlay
managers, we need to figure out which overlay managers to use for our crtcs. The
current approach is to use pipe2chan(), which returns a higher numbered manager
for the crtc.
The problem with this approach is that it assumes that the overlay managers we
choose will connect to the encoders the platform's panels are going to use,
this isn't true, an overlay manager connects only to a few outputs/encoders, and
choosing any overlay manager for our crtc might lead to a situation where the
encoder cannot connect to any of the crtcs we have chosen. For example, an
omap5-panda board has just one hdmi output. If num_crtc is set to 1, with the
current approach, pipe2chan will pick up the LCD2 overlay manager, which cannot
connect to the hdmi encoder at all. The only manager that could have connected
to hdmi was the TV overlay manager.
Therefore, there is a need to choose our overlay managers keeping in mind the
panels we have on that platform. The new approach iterates through all the
available panels, creates encoders and connectors for them, and then tries to
get a suitable overlay manager to create a crtc which can connect to the
encoders.
We use the dispc_channel field in omap_dss_output to retrieve the desired
overlay manager's channel number, we then check whether the manager had already
been assigned to a crtc or not. If it was already assigned to a crtc, we assume
that out of all the encoders which intend use this crtc, only one will run at a
time. If the overlay manager wan't assigned to a crtc till then, we create a
new crtc and link it with the overlay manager.
This approach just looks for the best dispc_channel for each encoder. On DSS HW,
some encoders can connect to multiple overlay managers. Since we don't try
looking for alternate overlay managers, there is a greater possibility that 2
or more encoders end up asking for the same crtc, causing only one encoder to
run at a time.
Also, this approach isn't the most optimal one, it can do either good or bad
depending on the sequence in which the panels/outputs are parsed. The optimal
way would be some sort of back tracking approach, where we improve the set of
managers we use as we iterate through the list of panels/encoders. That's
something left for later.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Now that the omapdss interface has been reworked so that omapdrm can use
dispc directly, we have been able to fix the remaining functional kms
issues with omapdrm. And in the mean time the PM sequencing and many
other of that open issues have been solved. So I think it makes sense
to finally move omapdrm out of staging.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|