aboutsummaryrefslogtreecommitdiff
path: root/drivers/gpu/drm/amd/display
AgeCommit message (Collapse)AuthorFilesLines
2024-01-29drm/amd/display: add debugfs disallow edp psrHersen Wu4-2/+67
[Why] fix reading edp rx crc timeout failure. after bootup, kernel setup psr with dpcd 0x170 = 5. this notify rx psr enable and let rx fw start checking crc for fw internal logic. rx fw may not update crc read count within dpcd 0x246. read count is always 0. this will lead tx crc reading timeout. [How] add debugfs to let test app to disbable rx crc checking for rx internal logic. then test app can read rx crc dpcd 0x246 successfully. expected app sequence is as below: 1. disable eDP PHY and notify eDP rx with dpcd 0x600 = 2. 2. echo 0x1 /sys/kernel/debug/dri/0/eDP-X/disallow_edp_enter_psr 3. enable eDP PHY and notify eDP rx with dpcd 0x600 = 1 but without dpcd 0x170 = 5. 4. read crc from rx dpcd 0x270, 0x246, etc. 5. echo 0x0 /sys/kernel/debug/dri/0/eDP-X/disallow_edp_enter_psr. this will let eDP back to normal with psr setup dpcd 0x170 = 5. Reviewed-by: Wayne Lin <[email protected]> Acked-by: Tom Chung <[email protected]> Signed-off-by: Hersen Wu <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-29drm/amd/display: For FPO and SubVP/DRR configs program vmin/max selAlvin Lee9-25/+56
[Why & How] For FPO and SubVP/DRR cases we need to ensure to program OTG_V_TOTAL_MIN/MAX_SEL, otherwise stretching the vblank in FPO / SubVP / DRR cases will not have any effect and we could hit underflow / corruption. Reviewed-by: Alvin Lee <[email protected]> Acked-by: Tom Chung <[email protected]> Signed-off-by: Alvin Lee <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-29drm/amd/display: Unify optimize_required flags and VRR adjustmentsAric Cyr5-17/+10
[why] There is only a single call to dc_post_update_surfaces_to_stream so there is no need to have two flags to control it. Unifying this to a single flag allows dc_stream_adjust_vmin_vmax to skip actual programming when there is no change required. [how] Remove wm_optimze_required flag and set only optimize_required in its place. Then in dc_stream_adjust_vmin_vmax, check that the stream timing range matches the requested one and skip programming if they are equal. Reviewed-by: Alvin Lee <[email protected]> Acked-by: Tom Chung <[email protected]> Signed-off-by: Aric Cyr <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-29drm/amd/display: increased min_dcfclk_mhz and min_fclk_mhzSohaib Nadeem1-1/+1
[why] Originally, PMFW said min FCLK is 300Mhz, but min DCFCLK can be increased to 400Mhz because min FCLK is now 600Mhz so FCLK >= 1.5 * DCFCLK hardware requirement will still be satisfied. Increasing min DCFCLK addresses underflow issues (underflow occurs when phantom pipe is turned on for some Sub-Viewport configs). [how] Increasing DCFCLK by raising the min_dcfclk_mhz Reviewed-by: Chaitanya Dhere <[email protected]> Reviewed-by: Alvin Lee <[email protected]> Acked-by: Tom Chung <[email protected]> Signed-off-by: Sohaib Nadeem <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-29drm/amd/display: Wait for mailbox ready when powering up DMCUBNicholas Kazlauskas1-2/+11
[Why] Otherwise we can send commands too early and they don't execute until the next command is sent. [How] Check the extra status bit when polling for HW powered up. Reviewed-by: Charlene Liu <[email protected]> Acked-by: Tom Chung <[email protected]> Signed-off-by: Nicholas Kazlauskas <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-29drm/amd/display: Wait before sending idle allow and after idle disallowNicholas Kazlauskas1-1/+6
[Why] We want acknowledgment of the driver idle disallow from DMCUB before continuing with any further programming. For idle allow we want to minimize the chance of DMCUB actively interacing with other firmware components on the system (eg. PMFW) at the same time. [How] Ensure that DMCUB isn't in the middle of processing other command submissions prior to allowing idle and after disallowing idle by inserting a wait before the allow and by changing the wait type for the idle disallow. Reviewed-by: Charlene Liu <[email protected]> Acked-by: Tom Chung <[email protected]> Signed-off-by: Nicholas Kazlauskas <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-29Revert "drm/amd/display: initialize all the dpm level's stutter latency"Charlene Liu1-3/+1
Revert commit 885c71ad791c ("drm/amd/display: initialize all the dpm level's stutter latency") Because it causes some regression Reviewed-by: Muhammad Ahmed <[email protected]> Acked-by: Tom Chung <[email protected]> Signed-off-by: Charlene Liu <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-29drm/amd/display: Fix static screen event mask definition changeYiling Chen10-27/+28
[why] The static screen event mask definition is different betwnn DCN31 after and before. [how] Rename DCN30_set_static_screen_control to DCN31. Reviewed-by: Charlene Liu <[email protected]> Acked-by: Tom Chung <[email protected]> Signed-off-by: Yiling Chen <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-29Documentation/gpu: Introduce a simple contribution list for display codeRodrigo Siqueira1-110/+0
This commit adds a contribution list for display under the kernel documentation with some first suggestions. It also drops an old TODO list from the display folder. Cc: Mario Limonciello <[email protected]> Cc: Alex Deucher <[email protected]> Cc: Harry Wentland <[email protected]> Cc: Hamza Mahfooz <[email protected]> Cc: Christian König <[email protected]> Cc: Aurabindo Pillai <[email protected]> Reviewed-by: Mario Limonciello <[email protected]> Acked-by: Christian König <[email protected]> Acked-by: Hamza Mahfooz <[email protected]> Signed-off-by: Rodrigo Siqueira <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-29Documentation/gpu: Add entry for the DIO componentRodrigo Siqueira1-0/+10
Cc: Mario Limonciello <[email protected]> Cc: Alex Deucher <[email protected]> Cc: Harry Wentland <[email protected]> Cc: Hamza Mahfooz <[email protected]> Cc: Christian König <[email protected]> Cc: Aurabindo Pillai <[email protected]> Reviewed-by: Mario Limonciello <[email protected]> Acked-by: Christian König <[email protected]> Acked-by: Hamza Mahfooz <[email protected]> Signed-off-by: Rodrigo Siqueira <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-29Documentation/gpu: Add entry for OPP in the kernel docRodrigo Siqueira1-0/+16
Introduce OPP as part of the kernel documentation. Cc: Mario Limonciello <[email protected]> Cc: Alex Deucher <[email protected]> Cc: Harry Wentland <[email protected]> Cc: Hamza Mahfooz <[email protected]> Cc: Christian König <[email protected]> Cc: Aurabindo Pillai <[email protected]> Reviewed-by: Mario Limonciello <[email protected]> Acked-by: Christian König <[email protected]> Acked-by: Hamza Mahfooz <[email protected]> Signed-off-by: Rodrigo Siqueira <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-29Documentation/gpu: Add kernel doc entry for MPCRodrigo Siqueira1-77/+173
This commit adds a kernel-doc entry for the MPC block. Since it enabled the kernel-doc to parse some of the documentation in the mpc.h file, fixing some of the comments was required. Cc: Mario Limonciello <[email protected]> Cc: Alex Deucher <[email protected]> Cc: Harry Wentland <[email protected]> Cc: Hamza Mahfooz <[email protected]> Cc: Christian König <[email protected]> Cc: Aurabindo Pillai <[email protected]> Reviewed-by: Mario Limonciello <[email protected]> Acked-by: Christian König <[email protected]> Acked-by: Hamza Mahfooz <[email protected]> Signed-off-by: Rodrigo Siqueira <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-29Documentation/gpu: Add kernel doc entry for DPPRodrigo Siqueira1-0/+25
This commit introduces basic DPP information and the struct scan for code documentation. Cc: Mario Limonciello <[email protected]> Cc: Alex Deucher <[email protected]> Cc: Harry Wentland <[email protected]> Cc: Hamza Mahfooz <[email protected]> Cc: Christian König <[email protected]> Cc: Aurabindo Pillai <[email protected]> Reviewed-by: Mario Limonciello <[email protected]> Acked-by: Christian König <[email protected]> Acked-by: Hamza Mahfooz <[email protected]> Signed-off-by: Rodrigo Siqueira <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-29drm/amd/display: Fix potential NULL pointer dereferences in ↵Srinivasan Shanmugam1-2/+5
'dcn10_set_output_transfer_func()' The 'stream' pointer is used in dcn10_set_output_transfer_func() before the check if 'stream' is NULL. Fixes the below: drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn10/dcn10_hwseq.c:1892 dcn10_set_output_transfer_func() warn: variable dereferenced before check 'stream' (see line 1875) Fixes: ddef02de0d71 ("drm/amd/display: add null checks before logging") Cc: Wyatt Wood <[email protected]> Cc: Anthony Koo <[email protected]> Cc: Rodrigo Siqueira <[email protected]> Cc: Aurabindo Pillai <[email protected]> Signed-off-by: Srinivasan Shanmugam <[email protected]> Reviewed-by: Anthony Koo <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-29Documentation/gpu: Add simple doc page for DCHUBBUBRodrigo Siqueira1-0/+6
Enable the documentation to extract code documentation from dchubbub.h file. Cc: Mario Limonciello <[email protected]> Cc: Alex Deucher <[email protected]> Cc: Harry Wentland <[email protected]> Cc: Hamza Mahfooz <[email protected]> Cc: Christian König <[email protected]> Cc: Aurabindo Pillai <[email protected]> Reviewed-by: Mario Limonciello <[email protected]> Acked-by: Christian König <[email protected]> Acked-by: Hamza Mahfooz <[email protected]> Signed-off-by: Rodrigo Siqueira <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-29Documentation/gpu: Add basic page for HUBPRodrigo Siqueira1-1/+12
Create the HUBP documentation page and add the doc references to extract the HUBP code documentation. Cc: Mario Limonciello <[email protected]> Cc: Alex Deucher <[email protected]> Cc: Harry Wentland <[email protected]> Cc: Hamza Mahfooz <[email protected]> Cc: Christian König <[email protected]> Cc: Aurabindo Pillai <[email protected]> Reviewed-by: Mario Limonciello <[email protected]> Acked-by: Christian König <[email protected]> Acked-by: Hamza Mahfooz <[email protected]> Signed-off-by: Rodrigo Siqueira <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-25drm/amd/display: "Enable IPS by default"Roman Li1-1/+2
[Why] IPS was temporary disabled due to instability. It was fixed in dmub firmware and with: - "drm/amd/display: Add IPS checks before dcn register access" - "drm/amd/display: Disable ips before dc interrupt setting" [How] Enable IPS by default. Disable IPS if 0x800 bit set in amdgpu.dcdebugmask module params Signed-off-by: Roman Li <[email protected]> Tested-by: Mark Broadworth <[email protected]> Reviewed-by: Mario Limonciello <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-25drm/amd/display: Disable ips before dc interrupt settingRoman Li1-1/+4
[Why] While in IPS2 an access to dcn registers is not allowed. If interrupt results in dc call, we should disable IPS. [How] Safeguard register access in IPS2 by disabling idle optimization before calling dc interrupt setting api. Signed-off-by: Roman Li <[email protected]> Tested-by: Mark Broadworth <[email protected]> Reviewed-by: Mario Limonciello <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-25drm/amd/display: Replay + IPS + ABM in Full Screen VPBChunTao Tso4-0/+57
[Why] Because ABM will wait VStart to start getting histogram data, it will cause we can't enter IPS while full screnn video playing. [How] Modify the panel refresh rate to the maximun multiple of current refresh rate. Reviewed-by: Dennis Chan <[email protected]> Acked-by: Roman Li <[email protected]> Signed-off-by: ChunTao Tso <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-25drm/amd/display: Add IPS checks before dcn register accessRoman Li1-10/+6
[Why] With IPS enabled a system hangs once PSR is active. PSR active triggers transition to IPS2 state. While in IPS2 an access to dcn registers results in hard hang. Existing check doesn't cover for PSR sequence. [How] Safeguard register access by disabling idle optimization in atomic commit and crtc scanout. It will be re-enabled on next vblank. Reviewed-by: Nicholas Kazlauskas <[email protected]> Acked-by: Roman Li <[email protected]> Signed-off-by: Roman Li <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-25drm/amd/display: Add Replay IPS register for DMUB command tableAlvin Lee1-0/+1
- Introduce a new Replay mode for DMUB version 0.0.199.0 Reviewed-by: Martin Leung <[email protected]> Acked-by: Alex Hung <[email protected]> Signed-off-by: Alvin Lee <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-25drm/amd/display: Allow IPS2 during ReplayNicholas Kazlauskas3-1/+11
[Why & How] Add regkey to block video playback in IPS2 by default Allow idle optimizations in the same spot we allow Replay for video playback usecases. Avoid sending it when there's an external display connected by modifying the allow idle checks to check for active non-eDP screens. Reviewed-by: Charlene Liu <[email protected]> Acked-by: Alex Hung <[email protected]> Signed-off-by: Nicholas Kazlauskas <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-25drm/amd/display: Fix uninitialized variable usage in core_link_ 'read_dpcd() ↵Srinivasan Shanmugam1-2/+2
& write_dpcd()' functions The 'status' variable in 'core_link_read_dpcd()' & 'core_link_write_dpcd()' was uninitialized. Thus, initializing 'status' variable to 'DC_ERROR_UNEXPECTED' by default. Fixes the below: drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dpcd.c:226 core_link_read_dpcd() error: uninitialized symbol 'status'. drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dpcd.c:248 core_link_write_dpcd() error: uninitialized symbol 'status'. Cc: [email protected] Cc: Jerry Zuo <[email protected]> Cc: Jun Lei <[email protected]> Cc: Wayne Lin <[email protected]> Cc: Aurabindo Pillai <[email protected]> Cc: Rodrigo Siqueira <[email protected]> Cc: Hamza Mahfooz <[email protected]> Signed-off-by: Srinivasan Shanmugam <[email protected]> Reviewed-by: Rodrigo Siqueira <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-25drm/amd/display: "Enable IPS by default"Roman Li1-1/+2
[Why] IPS was temporary disabled due to instability. It was fixed in dmub firmware and with: - "drm/amd/display: Add IPS checks before dcn register access" - "drm/amd/display: Disable ips before dc interrupt setting" [How] Enable IPS by default. Disable IPS if 0x800 bit set in amdgpu.dcdebugmask module params Signed-off-by: Roman Li <[email protected]> Tested-by: Mark Broadworth <[email protected]> Reviewed-by: Mario Limonciello <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-25drm/amd/display: Disable ips before dc interrupt settingRoman Li1-1/+4
[Why] While in IPS2 an access to dcn registers is not allowed. If interrupt results in dc call, we should disable IPS. [How] Safeguard register access in IPS2 by disabling idle optimization before calling dc interrupt setting api. Signed-off-by: Roman Li <[email protected]> Tested-by: Mark Broadworth <[email protected]> Reviewed-by: Mario Limonciello <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-25drm/amd/display: Fix a potential buffer overflow in 'dp_dsc_clock_en_read()'Srinivasan Shanmugam1-1/+1
Tell snprintf() to store at most 10 bytes in the output buffer instead of 30. Fixes the below: drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_debugfs.c:1508 dp_dsc_clock_en_read() error: snprintf() is printing too much 30 vs 10 Fixes: c06e09b76639 ("drm/amd/display: Add DSC parameters logging to debugfs") Cc: Alex Hung <[email protected]> Cc: Qingqing Zhuo <[email protected]> Cc: Rodrigo Siqueira <[email protected]> Cc: Aurabindo Pillai <[email protected]> Cc: Alex Deucher <[email protected]> Signed-off-by: Srinivasan Shanmugam <[email protected]> Reviewed-by: Harry Wentland <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: hook up DCN20 color blocks data to DTN logMelissa Wen4-15/+147
Color caps changed between HW versions, which caused the DCN10 color state sections in the DTN log to no longer match DCN2+ state. Create a color state log specific to DCN2.0 and hook it up to DCN2 family drivers. Instead of reading gamut remap reg values, display gamut remap matrix data in fixed 31.32. Signed-off-by: Melissa Wen <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: add DPP and MPC color caps to DTN logMelissa Wen2-0/+46
Add color caps information for DPP and MPC block to show HW color caps. Signed-off-by: Melissa Wen <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: Address kdoc for eDP Panel Replay feature in ↵Srinivasan Shanmugam1-0/+8
'amdgpu_dm_crtc_set_panel_sr_feature()' Fixes the below: drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_crtc.c:100: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst * The DRM vblank counter enable/disable action is used as the trigger to enable Cc: Sun peng Li <[email protected]> Cc: Alex Hung <[email protected]> Cc: Tom Chung <[email protected]> Cc: Rodrigo Siqueira <[email protected]> Cc: Aurabindo Pillai <[email protected]> Signed-off-by: Srinivasan Shanmugam <[email protected]> Reviewed-by: Tom Chung <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: hook up DCN30 color blocks data to DTN logMelissa Wen4-1/+135
Color caps changed between HW versions, which caused the DCN10 color state sections in the DTN log to no longer match DCN3+ state. Create a color state log specific to DCN3.0 and hook it up to DCN3.0+ and DCN3.1+ drivers. rfc-v2: - detail RAM mode for gamcor and blnd gamma blocks - add MPC gamut remap matrix log v3: - read MPC gamut remap matrix in fixed 31.32 format - extend to DCN3.0+ and DCN3.1+ drivers (Harry) Signed-off-by: Melissa Wen <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: Promote DAL to 3.2.269Aric Cyr1-1/+1
- FW Release 0.0.201.0 - Fix resizing video window for dcn321 - Fix timing bandwidth calculation for HDMI - Fix null-deref in dml2 assigned pipe search - Add GART memory support for dmcub - Add power_state and pme_pending flag - Add usb4_bw_alloc_support flag - Revert "Rework DC Z10 restore Acked-by: Roman Li <[email protected]> Signed-off-by: Aric Cyr <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: [FW Promotion] Release 0.0.201.0Anthony Koo1-9/+4
- Add debug flag for Replay IPS visual confirm - Remove unused debug flags that should not be controlled inside Replay FSM Acked-by: Roman Li <[email protected]> Signed-off-by: Anthony Koo <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: Replay + IPS + ABM in Full Screen VPBChunTao Tso4-0/+57
[Why] Because ABM will wait VStart to start getting histogram data, it will cause we can't enter IPS while full screnn video playing. [How] Modify the panel refresh rate to the maximun multiple of current refresh rate. Reviewed-by: Dennis Chan <[email protected]> Acked-by: Roman Li <[email protected]> Signed-off-by: ChunTao Tso <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: turn off windowed Mpo ODM feature for dcn321Wenjing Liu1-0/+1
[why] It has been found a regression caused by enabling this feature during ODM to MPC combine switch when user is resizing video window. The transition is only needed when the feature is enabled. During the transition driver will temporary switch to use max dppclk level through SMU set hard min interface. The interface times out and fail to configure the max dpp clock level, which caused system issue as the desired clock can't be set. We will continue investigating the issue and root cause the issue where max dppclk level can't be reached. But for now we have to disable this feature as this feature will cause us to hit this problem in common use cases during video playback unfortunately. The issue is dcn321 specific so it won't impact other dcn revisions. Reviewed-by: Martin Leung <[email protected]> Acked-by: Roman Li <[email protected]> Signed-off-by: Wenjing Liu <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: Add GART memory support for dmcubFudongwang3-67/+71
[Why] In dump file, GART memory can be accessed while frame buffer cannot. [How] Add GART memory support for dmcub. Reviewed-by: Nicholas Kazlauskas <[email protected]> Acked-by: Roman Li <[email protected]> Signed-off-by: Fudongwang <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: Revert "Rework DC Z10 restore"Charlene Liu3-15/+7
This reverts commit e6f82bd44b401049367fcdee3328c7c720351419. It caused intermittent hangs when enabling IPS on static screen. Reviewed-by: Nicholas Kazlauskas <[email protected]> Acked-by: Roman Li <[email protected]> Signed-off-by: Charlene Liu <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: add power_state and pme_pending flagMuhammad Ahmed2-0/+2
[what] Adding power_state to dc.h and pme_pending flag to clk_mgr_internal.h Reviewed-by: Charlene Liu <[email protected]> Acked-by: Roman Li <[email protected]> Signed-off-by: Muhammad Ahmed <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: Add IPS checks before dcn register accessRoman Li1-10/+6
[Why] With IPS enabled a system hangs once PSR is active. PSR active triggers transition to IPS2 state. While in IPS2 an access to dcn registers results in hard hang. Existing check doesn't cover for PSR sequence. [How] Safeguard register access by disabling idle optimization in atomic commit and crtc scanout. It will be re-enabled on next vblank. Reviewed-by: Nicholas Kazlauskas <[email protected]> Acked-by: Roman Li <[email protected]> Signed-off-by: Roman Li <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: Add NULL-checks in dml2 assigned pipe searchAllen Pan1-7/+12
[Why] NULL-deref regression after: "drm/amd/display: Fix dml2 assigned pipe search" [How] Add verification for potential NULLs Fixes: d451b534e0b4 ("drm/amd/display: Fix dml2 assigned pipe search") Reviewed-by: Charlene Liu <[email protected]> Reviewed-by: Nicholas Kazlauskas <[email protected]> Acked-by: Roman Li <[email protected]> Signed-off-by: Gabe Teeger <[email protected]> Signed-off-by: Allen Pan <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: Add usb4_bw_alloc_support flagPeichen Huang3-0/+77
[Why] dc should have a flag for DM to enable usb4_bw_alloc in dptx [How] - Add usb4_bw_alloc_support flag in dc_config Reviewed-by: Wayne Lin <[email protected]> Reviewed-by: Meenakshikumar Somasundaram <[email protected]> Acked-by: Roman Li <[email protected]> Signed-off-by: Peichen Huang <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: Promote DAL to 3.2.268Aric Cyr1-1/+1
Acked-by: Roman Li <[email protected]> Signed-off-by: Aric Cyr <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: create DCN3-specific log for MPC stateMelissa Wen2-1/+54
Logging DCN3 MPC state was following DCN1 implementation that doesn't consider new DCN3 MPC color blocks. Create new elements according to DCN3 MPC color caps and a new DCN3-specific function for reading MPC data. v3: - remove gamut remap reg reading in favor of fixed31_32 matrix data Signed-off-by: Melissa Wen <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: Fix timing bandwidth calculation for HDMILeo (Hanghong) Ma2-0/+6
[Why && How] The current bandwidth calculation for timing doesn't account for certain HDMI modes overhead which leads to DSC can't be enabled. Add support to calculate the actual bandwidth for these HDMI modes. Reviewed-by: Chris Park <[email protected]> Acked-by: Roman Li <[email protected]> Signed-off-by: Leo (Hanghong) Ma <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: add get_gamut_remap helper for MPC3Melissa Wen2-0/+62
We want to be able to read the MPC's gamut remap matrix similar to what we do with .dpp_get_gamut_remap functions. On the other hand, we don't need a hook here because only DCN3+ has the MPC gamut remap block, being absent in previous families. Signed-off-by: Melissa Wen <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: fill up DCN3 DPP color stateMelissa Wen2-2/+43
DCN3 DPP color state was uncollected and some state elements from DCN1 doesn't fit DCN3. Create new elements according to DCN3 color caps and fill them up for DTN log output. rfc-v2: - fix reading of gamcor and blnd gamma states - remove gamut remap register in favor of gamut remap matrix reading Signed-off-by: Melissa Wen <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: read gamut remap matrix in fixed-point 31.32 formatMelissa Wen2-12/+29
Instead of read gamut remap data from hw values, convert HW register values (S2D13) into a fixed-point 31.32 matrix for color state log. Change DCN10 log to print data in the format of the gamut remap matrix. Signed-off-by: Melissa Wen <[email protected]> Reviewed-by: Rodrigo Siqueira <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: Add dpp_get_gamut_remap functionsHarry Wentland16-3/+256
We want to be able to read the DPP's gamut remap matrix. v2: - code-style and doc comments clean-up (Melissa) Signed-off-by: Harry Wentland <[email protected]> Signed-off-by: Melissa Wen <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: decouple color state from hw state logMelissa Wen1-8/+18
Prepare to hook up color state log according to the DCN version. v3: - put functions in single line (Siqueira) Signed-off-by: Melissa Wen <[email protected]> Reviewed-by: Rodrigo Siqueira <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: Fix uninitialized variable usage in core_link_ 'read_dpcd() ↵Srinivasan Shanmugam1-2/+2
& write_dpcd()' functions The 'status' variable in 'core_link_read_dpcd()' & 'core_link_write_dpcd()' was uninitialized. Thus, initializing 'status' variable to 'DC_ERROR_UNEXPECTED' by default. Fixes the below: drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dpcd.c:226 core_link_read_dpcd() error: uninitialized symbol 'status'. drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dpcd.c:248 core_link_write_dpcd() error: uninitialized symbol 'status'. Cc: [email protected] Cc: Jerry Zuo <[email protected]> Cc: Jun Lei <[email protected]> Cc: Wayne Lin <[email protected]> Cc: Aurabindo Pillai <[email protected]> Cc: Rodrigo Siqueira <[email protected]> Cc: Hamza Mahfooz <[email protected]> Signed-off-by: Srinivasan Shanmugam <[email protected]> Reviewed-by: Rodrigo Siqueira <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2024-01-22drm/amd/display: Drop kdoc markers for some Panel Replay functionsSrinivasan Shanmugam1-2/+2
Fixes the below gcc with W=1: drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_replay.c:262: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst * Set REPLAY power optimization flags and coasting vtotal. drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_replay.c:284: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst * send Replay general cmd to DMUB. Fixes: e379787cbc2a ("drm/amd/display: Add some functions for Panel Replay") Cc: Aurabindo Pillai <[email protected]> Cc: Rodrigo Siqueira <[email protected]> Cc: Leo Li <[email protected]> Cc: Tom Chung <[email protected]> Signed-off-by: Srinivasan Shanmugam <[email protected]> Reviewed-by: Alex Deucher <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.