| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This commit corrects problems with the previous wake implementation
by implementing suspend and resume power management operations and
the driver shutdown operation.
Wake masks are used to keep track of which GPIO should wake the
device. On suspend the GPIO state is saved and the possible wakeup
sources are explicitly unmasked in the hardware. Non-wakeup sources
are explicitly masked so IRQCHIP_MASK_ON_SUSPEND is no longer
necessary. The saved state of the GPIO is restored upon resume.
It is important not to write to the GPIO status register since this
has the effect of clearing bits. The status register is explicitly
removed from the register save and restore to ensure this.
The shutdown operation allows the hardware to be put into the same
quiesced state as the suspend operation and removes the need for
the reboot notifier.
Unfortunately, there appears to be some confusion about whether
a pending disabled wake interrupt should wake the system. If a wake
capable interrupt is disabled using the default "lazy disable"
behavior and it is triggered before the suspend_device_irq call
the interrupt hardware will be acknowledged by mask_ack_irq and the
IRQS_PENDING flag is added to its state. However, the IRQS_PENDING
flag of wake interrupts is not checked to prevent the transition to
suspend and the hardware has been acked which prevents its wakeup.
If the lazy disabled interrupt is triggered after the call to
suspend_device_irqs then the wakeup logic will abort the suspend.
The irq_disable method is defined by this GPIO driver to prevent
lazy disable so that the pending hardware state remains asserted
allowing the hardware to wake and providing a consistent behavior.
In addition, the IRQ_DISABLE_UNLAZY flag is set for the non-wake
parent interrupt as a convenience to prevent the need to add code
to the brcmstb_gpio_irq_handler to support "lazy disable" of the
non-wake parent interrupt when it is disabled during suspend and
resume. Chained interrupt parents are not normally disabled, but
these GPIO devices have different parent interrupts for wake and
non-wake handling. It is convenient to mask the non-wake parent
when suspending to preserve the hardware state for proper wakeup
accounting when the driver is resumed.
Signed-off-by: Doug Berger <[email protected]>
Acked-by: Gregory Fong <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
The GPIOLIB IRQ chip helpers were very appealing, but badly broke
the 1:1 mapping between a GPIO controller's device_node and its
interrupt domain.
When another device-tree node references a GPIO device as its
interrupt parent, the irq_create_of_mapping() function looks for
the irq domain of the GPIO device and since all bank irq domains
reference the same GPIO device node it always resolves to the irq
domain of the first bank regardless of which bank the number of
the GPIO should resolve. This domain can only map hwirq numbers
0-31 so interrupts on GPIO above that can't be mapped by the
device-tree.
This commit effectively reverts the patch from Gregory Fong [1]
that was accepted upstream and replaces it with a consolidated
irq domain implementation with one larger interrupt domain per
GPIO controller instance spanning multiple GPIO banks based on
an earlier patch [2] also submitted by Gregory Fong.
[1] https://patchwork.kernel.org/patch/6921561/
[2] https://patchwork.kernel.org/patch/6347811/
Fixes: 19a7b6940b78 ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <[email protected]>
Reviewed-by: Gregory Fong <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
This commit corrects a bug when configuring the GPIO hardware for
IRQ_TYPE_LEVEL_LOW and IRQ_TYPE_LEVEL_HIGH interrupt types. The
hardware is now correctly configured to support those types.
Fixes: 19a7b6940b78 ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Acked-by: Gregory Fong <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
Reading and writing the gpio bank status register each time a pending
interrupt bit is serviced could cause new pending bits to be cleared
without servicing the associated interrupts.
By using the handle_level_irq flow instead of the handle_simple_irq
flow we get proper handling of interrupt masking as well as acking
of interrupts. The irq_ack method is added to support this.
Fixes: 19a7b6940b78 ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Acked-by: Gregory Fong <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
The basic memory-mapped GPIO controller lock must be released
before calling the registered GPIO interrupt handlers to allow
the interrupt handlers to access the hardware.
Examples of why a GPIO interrupt handler might want to access
the GPIO hardware include an interrupt that is configured to
trigger on rising and falling edges that needs to read the
current level of the input to know how to respond, or an
interrupt that causes a change in a GPIO output in the same
bank. If the lock is not released before enterring the handler
the hardware accesses will deadlock when they attempt to grab
the lock.
Since the lock is only needed to protect the calculation of
unmasked pending interrupts create a dedicated function to
perform this and hide the complexity.
Fixes: 19a7b6940b78 ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Acked-by: Gregory Fong <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
This commit allows a wakeup parent interrupt to be shared between
instances.
It also removes the redundant can_wake member of the private data
structure by using whether the parent_wake_irq has been defined to
indicate that the GPIO device can wake.
Fixes: 19a7b6940b78 ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Acked-by: Gregory Fong <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
Add a jump target so that a bit of exception handling can be better reused
at the end of this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
Using devm_ioremap_resource() has several advantages over devm_ioremap():
- it checks the passed resource's validity;
- it calls devm_request_mem_region() to check for the resource overlap;
- it prints an error message in case of error.
We can call devm_ioremap_resource() instead of devm_ioremap_nocache()
as ioremap() and ioremap_nocache() are implemented identically on ARM.
Doing this saves 2 LoCs and 80 bytes (AArch64 gcc 4.8.5).
Signed-off-by: Sergei Shtylyov <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
Some busses, like I2C, strictly need to have the line handled
as open drain, i.e. not actively driven high. For this reason
the i2c-gpio.c bit-banged I2C driver is reimplementing open
drain handling outside of gpiolib.
This is not very optimal. Instead make it possible for a
consumer to explcitly express that the line must be handled
as open drain instead of allowing local hacks papering over
this issue.
The descriptor tables, whether DT, ACPI or board files, should
of course have flagged these lines as open drain. E.g.:
enum gpio_lookup_flags GPIO_OPEN_DRAIN for a board file, or
gpios = <&foo 42 GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN>; in a
device tree using <dt-bindings/gpio/gpio.h>
But more often than not, these descriptors are wrong. So
we need to make it possible for consumers to enforce this
open drain behaviour.
We now have two new enumerated GPIO descriptor config flags:
GPIOD_OUT_LOW_OPEN_DRAIN and GPIOD_OUT_HIGH_OPEN_DRAIN
that will set up the lined enforced as open drain as output
low or high, using open drain (if the driver supports it)
or using open drain emulation (setting the line as input
to drive it high) from the gpiolib core.
Cc: [email protected]
Tested-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
It is possible to read all lines of a generic MMIO GPIO chip
with a single register read so support this if we are in
native endianness.
Add an especially quirky callback to read multiple lines for
the variants that require you to read values from the
output registers if and only if the line is set as output.
We managed to do that with a maximum of two register reads,
and just one read if the requested lines are all input or all
output.
Cc: Anton Vorontsov <[email protected]>
Cc: Lukas Wunner <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
The vtable call pin2mask() was introducing a vtable function call
in every gpiochip callback for a generic MMIO GPIO chip. This was
not exactly efficient. (Maybe link-time optimization could get rid of
it, I don't know.)
After removing all external calls into this API we can make it a
boolean flag in the struct gpio_chip call and sink the function into
the gpio-mmio driver yielding encapsulation and potential speedups.
Cc: Anton Vorontsov <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
The MPC8xxx driver is always instantiating its generic GPIO functions
with the flag BGPIOF_BIG_ENDIAN. This means "big-endian bit order"
and means the bits representing the GPIO lines in the registers are
reversed around 31 bits so line 0 is at bit 31 and so forth down to
line 31 in bit 0.
Instead of looping into the generic MMIO gpio to do the simple
calculation of a bitmask, through a vtable call with two parameters
likely using stack frames etc (unless the compiler optimize it)
and obscuring the view for the programmer, let's just open-code
what the call does. This likely executes faster, saves space and
makes the code easier to read.
Cc: Liu Gang <[email protected]>
Cc: Uwe Kleine-König <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
The pin2mask() accessor only shuffles BIT ORDER in big endian systems,
i.e. the bitstuffing is swizzled big endian so "bit 0" is bit 7 or
bit 15 or bit 31 or so.
The brcmstb only uses big endian BYTE ORDER which will be taken car of
by the ->write_reg() callback.
Just use BIT(offset) to assign the bit.
Acked-by: Gregory Fong <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
The pin2mask() accessor only shuffles BIT ORDER in big endian systems,
i.e. the bitstuffing is swizzled big endian so "bit 0" is bit 7 or
bit 15 or bit 31 or so.
The grgpio only uses big endian BYTE ORDER which will be taken car of
by the ->write_reg() callback.
Just use BIT(offset) to assign the bit.
Acked-by: Andreas Larsson <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
When no flags are given, the native endianness is used to access
the MMIO registers, and the pin2mask() call can simply be
converted to a BIT() call, as per the default pin2mask()
implementation in gpio-mmio.c.
Cc: Kelvin Cheung <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
The DW APB GPIO driver uses the generic GPIO library gpio-mmio,
and initialize the flags as "false", which should be 0.
When no flags are given, the native endianness is used to access
the MMIO registers, and the pin2mask() call can simply be
converted to a BIT() call, as per the default pin2mask()
implementation in gpio-mmio.c.
Acked-by: Alan Tull <[email protected]>
Acked-by: Hoan Tran <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
This GPIO controller is used on UniPhier SoC family.
It also serves as an interrupt controller, but interrupt signals are
just delivered to the parent irqchip without any latching or OR'ing.
This type of hardware can be well described with hierarchy IRQ domain.
One unfortunate thing for this device is that the interrupt mapping to
the interrupt parent is not contiguous.
I asked how DT can describe interrupt mapping between two irqchips [1],
but I could not find a good solution (at least in the framework level).
In fact, irqchip drivers using hierarchy domain generally hard-code the
DT binding of their parent.
After tackling on several approaches such as hard-code of hwirqs,
irq_domain_push_irq(), I ended up with a vendor specific property.
If we come up with a good idea to support this in the framework, we
can migrate over to it, but we can live with a driver-level solution
for now.
[1] https://lkml.org/lkml/2017/7/6/758
Signed-off-by: Masahiro Yamada <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
Literally.
I expect "lose" was meant here, rather than "loose", though you could feasibly
use a somewhat uncommon definition of "loose" to mean what would be meant by
"lose": "Loose the hounds" for instance, as in "Release the hounds".
Substituting in "value" for "hounds" gives "release the value", and makes some
sense, but futher substituting back to loose gives "loose the value" which
overall just seems a bit anachronistic.
Instead, use modern, pragmatic English and save a character.
Cc: Russell Currey <[email protected]>
Signed-off-by: Andrew Jeffery <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
The driver was developed for and tested with the MAX31913 built into
the Revolution Pi by KUNBUS, but should work with all members of the
MAX3191x family:
MAX31910: low power
MAX31911: LED drivers
MAX31912: LED drivers + 2nd voltage monitor + low power
MAX31913: LED drivers + 2nd voltage monitor
MAX31953: LED drivers + 2nd voltage monitor + isolation
MAX31963: LED drivers + 2nd voltage monitor + isolation + buck regulator
Cc: Mathias Duckeck <[email protected]>
Signed-off-by: Lukas Wunner <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
Replace the two separate calls for clearing the irqchip's chained handler
and its data with a single irq_set_chained_handler_and_data() call.
Signed-off-by: Martin Kaiser <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
OPEN_DRAIN and OPEN_SOURCE flags only affect the way we drive a GPIO
line, so they only make sense for output mode. Just as we only allow
input mode for event handle requests, don't allow passing open-drain
and open-source flags for any other mode than explicit output.
Signed-off-by: Bartosz Golaszewski <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
There's no need to check the validity of handle request flags more
than once, right after copying the data from user. Move the check
out of the for loop and simplify the error path by bailing out before
allocating any resources.
Signed-off-by: Bartosz Golaszewski <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
SPI-attached GPIO controllers typically read out all inputs in one go.
If callers desire the values of multipe inputs, ideally a single readout
should take place to return the desired values. However the current
driver API only offers a ->get callback but no ->get_multiple (unlike
->set_multiple, which is present). Thus, to read multiple inputs, a
full readout needs to be performed for every single value (barring
driver-internal caching), which is inefficient.
In fact, the lack of a ->get_multiple callback has been bemoaned
repeatedly by the gpio subsystem maintainer:
http://www.spinics.net/lists/linux-gpio/msg10571.html
http://www.spinics.net/lists/devicetree/msg121734.html
Introduce the missing callback. Add corresponding consumer functions
such as gpiod_get_array_value(). Amend linehandle_ioctl() to take
advantage of the newly added infrastructure. Update the documentation.
Cc: Rojhalat Ibrahim <[email protected]>
Signed-off-by: Lukas Wunner <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
Some platforms require reset to be released to allow register
access.
Signed-off-by: Alan Tull <[email protected]>
Reviewed-by: Philipp Zabel <[email protected]>
[Added DT bindings oneliner for standard reset binding]
Signed-off-by: Linus Walleij <[email protected]>
|
|
The SX150X driver was moved over to pin control a while back.
The GPIO Kconfig symbol creates a circular dependency since
it requires GPIOLIB and the pin control driver selects GPIOLIB
so get rid of the old annoying Kconfig option.
Signed-off-by: Linus Walleij <[email protected]>
|
|
Use the of_device_get_match_data() helper instead of open coding.
Note that the gpio-rcar driver is used with DT only, so there's always a
valid match.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
Now acking of edge irqs happens the following way:
- omap_gpio_irq_handler
- "isr" = read irq status
- omap_clear_gpio_irqbank(bank, isr_saved & ~level_mask);
^ clear edge status, so irq can be accepted
- loop while "isr"
generic_handle_irq()
- handle_edge_irq()
- desc->irq_data.chip->irq_ack(&desc->irq_data);
- omap_gpio_ack_irq()
it might be that at this moment edge IRQ was triggered again and it will be
cleared and IRQ will be lost.
Use handle_simple_irq and clear edge interrupts early without disabling them in
omap_gpio_irq_handler to avoid loosing interrupts.
[1] https://marc.info/?l=linux-omap&m=149004465313534&w=2
Signed-off-by: Grygorii Strashko <[email protected]>
Signed-off-by: Ladislav Michl <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
These request/free functions are just reimplementations of the
standard helpers in gpiolib. Delete them and replace with the
helpers.
Acked-by: Robert Jarzmik <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
Currently calls to:
gpiod_direction_output_raw()
gpiod_set_raw_value()
gpiod_set_raw_array_value()
gpiod_set_raw_value_cansleep()
gpiod_set_raw_array_value_cansleep()
Respect that we do not want to invert the value written, but will
still apply special open drain/open source semantics if the line has
an open drain/open source flag.
It also forbids us from driving an output marked as an interrupt
line.
This does not fit with the function name and expected semantics. In
the w1 host driver (for example) we need to handle a line as open drain
but sometimes force it to pull up, which means we should be able to
use the gpiod_set_raw_value() for this, but it currently does not
work.
There are also use cases where users actually want to drive a line
used by an interrupt. This is what they should be expected to use
the *raw* accessors for.
I have looked over the current users of this API and they do not seem
to be using the *raw* accessors with open drain or open source so let's
augment this behaviour before we have users expecting the inconsistent
semantic.
Signed-off-by: Linus Walleij <[email protected]>
|
|
The arbitrarily marking of a function with _ or __ is taking to mean
"perform some inner core of the caller" or something like that. At other
times, this syntax has a totally different meaning.
I don't like this since it is unambious and unhelpful to people reading
the code, so replace it with _commit() suffixes.
Signed-off-by: Linus Walleij <[email protected]>
|
|
The irq_domain_ops.activate() callback has no return value and no way to
tell the function that the activation is early.
The upcoming changes to support a reservation scheme which allows to assign
interrupt vectors on x86 only when the interrupt is actually requested
requires:
- A return value, so activation can fail at request_irq() time
- Information that the activate invocation is early, i.e. before
request_irq().
Signed-off-by: Thomas Gleixner <[email protected]>
Tested-by: Juergen Gross <[email protected]>
Tested-by: Yu Chen <[email protected]>
Acked-by: Juergen Gross <[email protected]>
Cc: Boris Ostrovsky <[email protected]>
Cc: Tony Luck <[email protected]>
Cc: Marc Zyngier <[email protected]>
Cc: Alok Kataria <[email protected]>
Cc: Joerg Roedel <[email protected]>
Cc: "Rafael J. Wysocki" <[email protected]>
Cc: Steven Rostedt <[email protected]>
Cc: Christoph Hellwig <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Paolo Bonzini <[email protected]>
Cc: Rui Zhang <[email protected]>
Cc: "K. Y. Srinivasan" <[email protected]>
Cc: Arjan van de Ven <[email protected]>
Cc: Dan Williams <[email protected]>
Cc: Len Brown <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
This driver implements .alloc() hook, so .map() is not used.
Signed-off-by: Masahiro Yamada <[email protected]>
Tested-by: David Daney <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
The pinctrl_request_gpio() and pinctrl_free_gpio() break the nice
namespacing in the other cross-calls like pinctrl_gpio_foo().
Just rename them and all references so we have one namespace
with all cross-calls under pinctrl_gpio_*().
Signed-off-by: Linus Walleij <[email protected]>
|
|
devm_kasprintf() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
devm_kasprintf() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
The probe function calls omap_gpio_show_rev(), which on most
compilers is inlined, but on the old gcc-4.6 is not, causing
a valid warning about the incorrect __init annotation:
WARNING: vmlinux.o(.text+0x40f614): Section mismatch in reference from the function omap_gpio_probe() to the function .init.text:omap_gpio_show_rev()
The function omap_gpio_probe() references
the function __init omap_gpio_show_rev().
This is often because omap_gpio_probe lacks a __init
annotation or the annotation of omap_gpio_show_rev is wrong.
This removes the __init.
Signed-off-by: Arnd Bergmann <[email protected]>
Acked-by: Santosh Shilimkar <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
This patch supports irq_set_wake for dwapb gpio. It allows GPIOs
to be configured as wakeup sources and wake the system from suspend.
Signed-off-by: Hoan Tran <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
Since f94277af03ea ("of/platform: Initialise dev->fwnode appropriately"),
of_platform_device_create() already initialises dev->fwnode to that of
the appropriate device_node, so within the driver we shouldn't need to
care whether we probed via DT or ACPI.
Signed-off-by: Robin Murphy <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
gcc-7 notices that the pin_table is an array of 16-bit numbers,
but fails to take the following range check into account:
drivers/gpio/gpiolib-acpi.c: In function 'acpi_gpiochip_request_interrupt':
drivers/gpio/gpiolib-acpi.c:206:24: warning: '%02X' directive writing between 2 and 4 bytes into a region of size 3 [-Wformat-overflow=]
sprintf(ev_name, "_%c%02X",
^~~~
drivers/gpio/gpiolib-acpi.c:206:20: note: directive argument in the range [0, 65535]
sprintf(ev_name, "_%c%02X",
^~~~~~~~~
drivers/gpio/gpiolib-acpi.c:206:3: note: 'sprintf' output between 5 and 7 bytes into a destination of size 5
sprintf(ev_name, "_%c%02X",
^~~~~~~~~~~~~~~~~~~~~~~~~~~
agpio->triggering == ACPI_EDGE_SENSITIVE ? 'E' : 'L',
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
pin);
~~~~
As suggested by Andy, this changes the format string to have a fixed length.
Since modifying the range check did not help, I also opened a bug against
gcc, see link below.
Fixes: 0d1c28a449c6 ("gpiolib-acpi: Add ACPI5 event model support to gpio.")
Cc: Andy Shevchenko <[email protected]>
Link: https://patchwork.kernel.org/patch/9840801/
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82123
Signed-off-by: Arnd Bergmann <[email protected]>
Acked-by: Mika Westerberg <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
IRQ_DOMAIN_HIERARCHY is not user-configurable, but supposed to be
selected by drivers that need IRQ domain hierarchy support.
GPIO_THUNDERX is the only user of "depends on IRQ_DOMAIN_HIERARCHY".
This means, we can not enable GPIO_THUNDERX unless other drivers
select IRQ_DOMAIN_HIERARCHY elsewhere. This is odd. Flip the logic.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: David Daney <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v4.14 cycle.
Not so much changes this time, phew. David Daney and Bartosz
Golaszewski did all the really interesting work in infrastructure
improvement across GPIO and IRQ core, hats off for them and to tglx
and Marc Z for general help with these patch sets.
Core changes:
- Allow the GPIO irqchip to allocate IRQs dynamically. This is an
important change on systems where only a restricted number of IRQs,
lesser than the number of GPIO lines, can be utilized. Now we can
allocate these on a first-come-first-served basis instead of
hogging up valuable IRQ lines.
- Serious fix-up of the kerneldoc documentation and inclusion into
the kerneldoc builds.
- Pulled in the IRQ simulator from the IRQ core tree and use this in
the GPIO mockup driver for exhaustive testing of interrupt
abilities.
New drivers:
- New driver for ThunderX and OCTEON-TX. This is especially
interesting as it picks up improvements from the IRQ core that
allow us to handle fasteoi ACKs upwards in a hierarchy when there
are IRQ flag latches on several levels in a hierarchy. Very
interesting work here.
- New subdriver for Renesas R-Car r8a7745 (RZ/G1E).
Misc:
- Several fixes and improvements for Xilinx Zynq GPIO.
- Support an enablement GPIO for the 74x164 GPIO.
- Switch a bunch of chips to use devres to allocate irq descriptors.
- A bunch of constification fixes"
* tag 'gpio-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (63 commits)
gpio: mockup: remove unused variable gc
gpio: pl061: constify amba_id
Revert "gpiolib: request the gpio before querying its direction"
gpio: twl6040: remove unneeded forward declaration
gpio: zevio: make gpio_chip const
gpio: add gpio_add_lookup_tables() to add several tables at once
gpio: rcar: Add r8a7745 (RZ/G1E) support
gpio: brcmstb: check return value of gpiochip_irqchip_add()
MAINTAINERS: Add entry for THUNDERX GPIO Driver.
gpio: Add gpio driver support for ThunderX and OCTEON-TX
gpio: mockup: use irq_sim
gpio: mxs: use devres for irq generic chip
gpio: mxc: use devres for irq generic chip
gpio: pch: use devres for irq generic chip
gpio: ml-ioh: use devres for irq generic chip
gpio: sta2x11: use devres for irq generic chip
gpio: sta2x11: disallow unbinding the driver
gpio: mxs: disallow unbinding the driver
gpio: mxc: disallow unbinding the driver
gpio: aspeed: Remove reference to clock name in debounce warning message
...
|
|
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <[email protected]>
Acked-by: Greg Kroah-Hartman <[email protected]>
Acked-by: Alexandre Belloni <[email protected]>
Acked-by: Mark Brown <[email protected]>
Acked-by: Sebastian Reichel <[email protected]>
Acked-by: Jonathan Cameron <[email protected]>
Acked-by: Dmitry Torokhov <[email protected]>
Acked-by: Kishon Vijay Abraham I <[email protected]>
Acked-by: Bartlomiej Zolnierkiewicz <[email protected]>
Acked-by: Thierry Reding <[email protected]>
Acked-by: Tony Lindgren <[email protected]>
Acked-by: Daniel Thompson <[email protected]>
Acked-by: Linus Walleij <[email protected]>
Acked-by: Guenter Roeck <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
|
|
The variable gc is assigned but never read and is redundant. Remove it.
Cleans up clang warning:
drivers/gpio/gpio-mockup.c:169:2: warning: Value stored to 'gc' is never read
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
This reverts commit 108d23e322a247d9f89ba2e2742520ead0944cc9.
It turns out this causes a regression on the OMAP, Marvell
and Renesas.
Reported-by: Tony Lindgren <[email protected]>
Reported-by: Thomas Petazzoni <[email protected]>
Reported-by: Jacopo Mondi <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
There is no reference to twl6040gpo_chip before its definition.
Signed-off-by: Masahiro Yamada <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
Make this const as it is only used as a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
When converting legacy board to use gpiod API() there might be several
lookup tables in board file, let's provide a way to register them all at
once.
Reviewed-by: Andy Shevchenko <[email protected]>
Reviewed-by: Mika Westerberg <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|