| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This adds an endianness conversion when setting the baudrate using a
vendor-specific command. Otherwise, bad things might happen on a big-
endian system.
Suggested-by: Marcel Holtmann <[email protected]>
Signed-off-by: David Lechner <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
This adds a #define for the vendor-specific HCI command to set the
baudrate instead of using the bare 0xff36 multiple times.
Signed-off-by: David Lechner <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
When a TI Bluetooth chip is reset, it takes about 100ms for the RTS line of
the chip to deassert. For my use case with a TI CC2560A chip, this delay
was not long enough and caused the local UART to never transmit at all (TI
AM1808 SoC UART2).
We can wait for the CTS signal using serdev_device_wait_for_cts() instead
of trying to guess using msleep().
Also changed the comment to be more informative while we are touching this
code.
Signed-off-by: David Lechner <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
The bt_* printk macros include a \n already, so we don't need extra ones
here.
Signed-off-by: David Lechner <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
BCM43341 devices soldered onto the PCB (non-removable) always (AFAICT)
use an UART connection for bluetooth. But they also advertise btsdio
support on their 3th sdio function, this causes 2 problems:
1) A non functioning BT HCI getting registered
2) Since the btsdio driver does not have suspend/resume callbacks,
mmc_sdio_pre_suspend will return -ENOSYS, causing mmc_pm_notify()
to react as if the SDIO-card is removed and since the slot is
marked as non-removable it will never get detected as inserted again.
Which results in wifi no longer working after a suspend/resume.
This commit fixes both by making btsdio ignore BCM43341 devices
when connected to a slot which is marked non-removable.
Cc: [email protected]
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
The Asus T100HA laptop uses an ACPI HID of BCM2E72 for the bluetooth
part of the SDIO bcm43340 wifi/bt combo chip.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
In case of hci send frame failure, skb is still owned
by the caller (hci_core) and then should not be freed.
This fixes crash on dragonboard-410c when sending SCO
packet. skb is freed by both btqcomsmd and hci_core.
Fixes: 1511cc750c3d ("Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver")
Signed-off-by: Loic Poulain <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
John Stultz reports a boot time crash with the HiKey board (which uses
hci_serdev) occurring in hci_uart_tx_wakeup(). That function is
contained in hci_ldisc.c, but also called from the newer hci_serdev.c.
It acquires the proto_lock in struct hci_uart and it turns out that we
forgot to init the lock in the serdev code path, thus causing the crash.
John bisected the crash to commit 67d2f8781b9f ("Bluetooth: hci_ldisc:
Allow sleeping while proto locks are held"), but the issue was present
before and the commit merely exposed it. (Perhaps by luck, the crash
did not occur with rwlocks.)
Init the proto_lock in the serdev code path to avoid the oops.
Stack trace for posterity:
Unable to handle kernel read from unreadable memory at 406f127000
[000000406f127000] user address but active_mm is swapper
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Hardware name: HiKey Development Board (DT)
Call trace:
hci_uart_tx_wakeup+0x38/0x148
hci_uart_send_frame+0x28/0x38
hci_send_frame+0x64/0xc0
hci_cmd_work+0x98/0x110
process_one_work+0x134/0x330
worker_thread+0x130/0x468
kthread+0xf8/0x128
ret_from_fork+0x10/0x18
Link: https://lkml.org/lkml/2017/11/15/908
Reported-and-tested-by: John Stultz <[email protected]>
Cc: Ronald Tschalär <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: Sumit Semwal <[email protected]>
Signed-off-by: Lukas Wunner <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
Fix: drivers/bluetooth/Kconfig:35:warning: multi-line strings not
supported warning.
Reported-by: Stephen Rothwell <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
On many laptops the btusb device is the only USB device not having USB
autosuspend enabled, this causes not only the HCI but also the USB
controller to stay awake, together using aprox. 0.4W of power.
Modern ultrabooks idle around 6W (at 50% screen brightness), 3.5W for
Apollo Lake devices. 0.4W is a significant chunk of this (7 / 11%).
The btusb driver already contains code to allow enabling USB autosuspend,
but currently leaves it up to the user / userspace to enable it. This
means that for most people it will not be enabled, leading to an
unnecessarily high power consumption.
Since enabling it is not entirely without risk of regressions, this
commit adds a Kconfig option so that Linux distributions can choose to
enable it by default. This commit also adds a module option so that when
distros receive bugs they can easily ask the user to disable it again
for easy debugging.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
Assuming that the original code idea was to enable in-band sleeping
only if the setup_rome method returns succes and run in 'standard'
mode otherwise, we should not return setup_rome return value which
makes qca_setup fail if no rampatch/nvm file found.
This fixes BT issue on the dragonboard-820C p4 which includes the
following QCA controller:
hci0: Product:0x00000008
hci0: Patch :0x00000111
hci0: ROM :0x00000302
hci0: SOC :0x00000044
Since there is no rampatch for this controller revision, just make
it work as is.
Signed-off-by: Loic Poulain <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
Signed-off-by: Al Viro <[email protected]>
|
|
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <[email protected]>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <[email protected]>
Reviewed-by: Philippe Ombredanne <[email protected]>
Reviewed-by: Thomas Gleixner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The following race condition still existed:
P1 P2
cancel_work_sync()
hci_uart_tx_wakeup()
hci_uart_write_work()
hci_uart_dequeue()
clear_bit(HCI_UART_PROTO_READY)
hci_unregister_dev(hdev)
hci_free_dev(hdev)
hu->proto->close(hu)
kfree(hu)
access to hdev and hu
Cancelling the work after clearing the HCI_UART_PROTO_READY bit avoids
this as any hci_uart_tx_wakeup() issued after the flag is cleared will
detect that and not schedule further work.
Signed-off-by: Ronald Tschalär <[email protected]>
Reviewed-by: Lukas Wunner <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
The recent MacBook's with multi-function USB interfaces for HID and
Bluetooth operation have the isochronous interface on number 3 instead
of number 1. Store the interface number and use it.
P: Vendor=05ac ProdID=8290 Rev= 1.40
S: Manufacturer=Broadcom Corp.
S: Product=Bluetooth USB Host Controller
C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA
A: FirstIf#= 2 IfCount= 4 Cls=ff(vend.) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=01 Driver=usbhid
E: Ad=85(I) Atr=03(Int.) MxPS= 8 Ivl=10ms
I:* If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=usbhid
E: Ad=86(I) Atr=03(Int.) MxPS= 8 Ivl=10ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 3 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 3 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 3 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 3 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 3 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Marcel Holtmann <[email protected]>
Signed-off-by: Johan Hedberg <[email protected]>
|
|
The format of Intel Bluetooth firmware for bootloader product is
ibt-<hw_variant>-<device_revision_id>.sfi and .ddc.
But for the SKU's 9x60, there a 3 variants of FW, which cannot be
differentiated just with hw_variant and devision_revision_id.
So to pick the appropriate FW file for 9x60 SKU's, it will be
differentiated using hw_variant, hw_revision and fw_revision rather
than hw_variant and device_revision_id only.
Format will be like this:
ibt-<hw_variant>-<hw_revision>-<fw_revision>.sfi and .ddc
Signed-off-by: Jaya P G <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
Signed-off-by: Johan Hedberg <[email protected]>
|
|
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and
bt_dev_info when possible. This allows for controller specific
reporting.
Signed-off-by: Marcel Holtmann <[email protected]>
Signed-off-by: Johan Hedberg <[email protected]>
|
|
Introduce ath_vendor_cmd function which can be used to
configure 'tags' and patch the firmware.
ATH vendor command has the following format:
| OPCODE (u8) | INDEX (LE16) | DLEN (U8) | DATA (U8 * DLEN) |
BD address configuration tag is at index 0x0001.
Signed-off-by: Loic Poulain <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
This change allows proper low power mode entry in suspend.
/sys/kernel/debug/usb/devices entry:
T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=03 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e09f Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Bartosz Chronowski <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
Commit dec2c92880cc5435381d50e3045ef018a762a917 ("Bluetooth: hci_ldisc:
Use rwlocking to avoid closing proto races") introduced locks in
hci_ldisc that are held while calling the proto functions. These locks
are rwlock's, and hence do not allow sleeping while they are held.
However, the proto functions that hci_bcm registers use mutexes and
hence need to be able to sleep.
In more detail: hci_uart_tty_receive() and hci_uart_dequeue() both
acquire the rwlock, after which they call proto->recv() and
proto->dequeue(), respectively. In the case of hci_bcm these point to
bcm_recv() and bcm_dequeue(). The latter both acquire the
bcm_device_lock, which is a mutex, so doing so results in a call to
might_sleep(). But since we're holding a rwlock in hci_ldisc, that
results in the following BUG (this for the dequeue case - a similar
one for the receive case is omitted for brevity):
BUG: sleeping function called from invalid context at kernel/locking/mutex.c
in_atomic(): 1, irqs_disabled(): 0, pid: 7303, name: kworker/7:3
INFO: lockdep is turned off.
CPU: 7 PID: 7303 Comm: kworker/7:3 Tainted: G W OE 4.13.2+ #17
Hardware name: Apple Inc. MacBookPro13,3/Mac-A5C67F76ED83108C, BIOS MBP133.8
Workqueue: events hci_uart_write_work [hci_uart]
Call Trace:
dump_stack+0x8e/0xd6
___might_sleep+0x164/0x250
__might_sleep+0x4a/0x80
__mutex_lock+0x59/0xa00
? lock_acquire+0xa3/0x1f0
? lock_acquire+0xa3/0x1f0
? hci_uart_write_work+0xd3/0x160 [hci_uart]
mutex_lock_nested+0x1b/0x20
? mutex_lock_nested+0x1b/0x20
bcm_dequeue+0x21/0xc0 [hci_uart]
hci_uart_write_work+0xe6/0x160 [hci_uart]
process_one_work+0x253/0x6a0
worker_thread+0x4d/0x3b0
kthread+0x133/0x150
We can't replace the mutex in hci_bcm, because there are other calls
there that might sleep. Therefore this replaces the rwlock's in
hci_ldisc with rw_semaphore's (which allow sleeping). This is a safer
approach anyway as it reduces the restrictions on the proto callbacks.
Also, because acquiring write-lock is very rare compared to acquiring
the read-lock, the percpu variant of rw_semaphore is used.
Lastly, because hci_uart_tx_wakeup() may be called from an IRQ context,
we can't block (sleep) while trying acquire the read lock there, so we
use the trylock variant.
Signed-off-by: Ronald Tschalär <[email protected]>
Reviewed-by: Lukas Wunner <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
In this particular case, notice that I replaced the
"deliberate fall-through..." comment with a "fall through"
comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
product id"
Commit 9834e586fa66 ("Bluetooth: btusb: Add workaround for Broadcom devices
without product id") was added to deal with the BT part of the BCM4356A2
on GPD pocket laptops having an usb vid:pid of 0000:0000.
After another commit to add support for the BCM UART connected BT ACPI-id
BCM2E7E used on the GPD win, it turns out that the BT on the GPD pocket is
connected via both USB and UART. Adding support for the BCM2E7E ACPI-id
causes it to switch to UART mode.
The Windows shipped with the device is using it in UART mode and the
presence of the BCM2E7E ACPI-id combined with the all 0 USB vid:pid
indicates that the BT part was never meant to be used in USB mode.
With the recent patches to use serdev device enumeration / instantiation
for UART attached ACPI enumerated BT devices, everything work OOTB in UART
mode and the workaround for the all 0 USB vid:pid is no longer needed.
This reverts commit 9834e586fa ("Bluetooth: btusb: Add workaround for
Broadcom devices without product id").
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
Tested on a GPD win with a BCM4356 PCI-E wifi/bt combo card.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
This patch adds the device ID for the bluetooth chip used in the
Broadcom BCM4356 PCI-E WiFi / UART BT chip.
Successfully tested using Firmware version 0273
The upper nibble of the rev field is 2 on this device, so this commit
also adds handling of 2 to the switch-case done on the upper nibble.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
It is no longer possible to build BT_HCIUART into the kernel
when SERIAL_DEV_BUS is a loadable module, even if none of the
SERIAL_DEV_BUS based implementations are selected:
drivers/bluetooth/hci_ldisc.o: In function `hci_uart_set_flow_control':
hci_ldisc.c:(.text+0xb40): undefined reference to `serdev_device_set_flow_control'
hci_ldisc.c:(.text+0xb5c): undefined reference to `serdev_device_set_tiocm'
This adds a dependency to avoid the broken configuration.
Fixes: 7841d554809b ("Bluetooth: hci_uart_set_flow_control: Fix NULL deref when using serdev")
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
This was introduced by the rework adding PM support:
drivers/bluetooth/hci_bcm.c: In function 'bcm_device_exists':
drivers/bluetooth/hci_bcm.c:156:22: error: 'struct bcm_device' has no member named 'hu'
if (device && device->hu && device->hu->serdev)
^~
The pointer is not available otherwise, so I'm enclosing
all references in an #ifdef here.
Fixes: 8a92056837fd ("Bluetooth: hci_bcm: Add (runtime)pm support to the serdev driver")
Signed-off-by: Arnd Bergmann <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
The MINIX NEO Z83-4 and MINIX NEO Z83-4 Pro devices use an AP6255 chip
for wifi and bluetooth. Bluetooth requires an ACPI device id of BCM2EA4
with BCM4345 rev C0 firmware.
This patch defines the firmware subversion.
Signed-off-by: Ian W MORRISON <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
The MINIX NEO Z83-4 and MINIX NEO Z83-4 Pro devices use an AP6255 chip for
wifi and bluetooth. Bluetooth requires an ACPI device id of BCM2EA4 with
BCM4345 rev C0 firmware.
This patch adds the device id and to use trigger type IRQF_TRIGGER_FALLING
as defined by 'GpioInt' in the ACPI DSDT table:
Device (BLT0)
{
Name (_HID, "BCM2EA4") // _HID: Hardware ID
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (UBUF, ResourceTemplate ()
{
UartSerialBusV2 (0x0001C200, DataBitsEight, StopBitsOne,
0xFC, LittleEndian, ParityTypeNone, FlowControlHardware,
0x0020, 0x0020, "\\_SB.PCI0.URT1",
0x00, ResourceConsumer, , Exclusive,
)
GpioInt (Level, ActiveLow, Exclusive, PullNone, 0x0000,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0005
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0007
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0004
}
})
Return (UBUF) /* \_SB_.PCI0.URT1.BLT0._CRS.UBUF */
}
}
Signed-off-by: Ian W MORRISON <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
The hci_bcm platform-device hack which was used to implement
power management for ACPI devices is being replaced by a
serial-device-bus implementation.
Unfortunately, when the corresponding change to the ACPI code lands (a
change that will stop enumerating and registering the serial-device-node
child as a platform device) PM will break silently unless serdev
TTY-port controller support has been enabled. Specifically, hciattach
(btattach) would still succeed, but power management would no longer
work.
Although this is strictly a runtime dependency, let's make the driver
depend on SERIAL_DEV_CTRL_TTYPORT, which is the particular serdev
controller implementation used by the ACPI devices currently managed by
this driver, to avoid breaking PM without anyone noticing.
Note that the driver already has a (build-time) dependency on the serdev
bus code.
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
As the overwriting of IRQ polarity to active low occurs during the driver
probe using 'bt_dev_warn' to display the warning results in '(null)' being
displayed for the device. This patch uses 'dev_warn' to correctly display
the device in the warning instead.
Signed-off-by: Ian W MORRISON <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. As already done in hci_qca, add
struct hci_uart pointer to priv structure.
Signed-off-by: Kees Cook <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
Make the serdev driver use struct bcm_device as its driver data and share
all the pm / GPIO / IRQ related code paths with the platform driver.
After this commit the 2 drivers are in essence the same and the serdev
driver interface can be used for all ACPI enumerated HCI UARTs.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
Use dev_get_drvdata instead of platform_get_drvdata in the suspend /
resume functions. This is a preparation patch for adding (runtime)pm
support to the serdev path.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
The ACPI subsys is going to move over to instantiating ACPI enumerated
HCIs as serdevs, rather then as platform devices.
So we need to make bcm_acpi_probe() suitable for use on non platform-
devices too, which means that we cannot rely on platform_get_irq()
getting called.
This commit modifies bcm_acpi_probe() to directly get the irq from
the ACPI resources, this is a preparation patch for adding (runtime)pm
support to the serdev path.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
After our previous changes, there is nothing platform specific about
bcm_platform_probe anymore, rename it to bcm_get_resources.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
The ACPI subsys is going to move over to instantiating ACPI enumerated
HCIs as serdevs, rather then as platform devices.
This means that the serdev driver paths of hci_bcm.c also need to start
supporting (runtime)pm through GPIOs and a host-wake IRQ.
The hci_bcm code is already mostly independent of how the HCI gets
instantiated, but even though the code only cares about pdev->dev, it
was storing pdev itself in struct bcm_device.
This commit stores pdev->dev rather then pdev in struct bcm_device, this
is a preparation patch for adding (runtime)pm support to the serdev path.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
The ACPI subsys is going to move over to instantiating ACPI enumerated
HCIs as serdevs, rather then as platform devices.
Most of the code in bcm_platform_probe is actually not platform
specific and will work with any struct device passed to it, the one
platform specific call in bcm_platform_probe is platform_get_irq.
This commit moves platform_get_irq call to the platform-driver's bcm_probe
function, this is a preparation patch for adding (runtime)pm support to
the serdev path.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
Since bcm_acpi_probe calls bcm_platform_probe, bcm_probe always ends up
calling bcm_platform_probe.
This commit simplifies things by making bcm_probe always call
bcm_platform_probe itself.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
This commit fixes 2 issues with host-wake irq trigger type handling
in hci_bcm:
1) bcm_setup_sleep sets sleep_params.host_wake_active based on
bcm_device.irq_polarity, but bcm_request_irq was always requesting
IRQF_TRIGGER_RISING as trigger type independent of irq_polarity.
This was a problem when the irq is described as a GpioInt rather then
an Interrupt in the DSDT as for GpioInt-s the value passed to request_irq
is honored. This commit fixes this by requesting the correct trigger
type depending on bcm_device.irq_polarity.
2) bcm_device.irq_polarity was used to directly store an ACPI polarity
value (ACPI_ACTIVE_*). This is undesirable because hci_bcm is also
used with device-tree and checking for something like ACPI_ACTIVE_LOW
in a non ACPI specific function like bcm_request_irq feels wrong.
This commit fixes this by renaming irq_polarity to irq_active_low
and changing its type to a bool.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
Fix a NULL pointer deref (hu->tty) when calling hci_uart_set_flow_control
on hci_uart-s using serdev.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
pr_err(), dev_err() and pr_info() messages should terminated with
a new-line to avoid other messages being concatenated onto the end.
Signed-off-by: Arvind Yadav <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
Retrieve BD address from the local-bd-address property.
This address must be unique and is usually added in the DT
by the bootloader which has access to the provisioned data.
Signed-off-by: Loic Poulain <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
This patch implements the hdev setup function since wcnss-bt does not have
persistent memory to store an allocated BD address. The device is therefore
marked as unconfigured if no BD address has been previously retrieved.
Signed-off-by: Loic Poulain <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
Cc: [email protected]
|
|
The Broadcom controller on the Raspberry Pi3 sends an empty packet with
packet type 0x00 after launching the firmware. This will cause logging
of errors.
Bluetooth: hci0: Frame reassembly failed (-84)
Since this seems to be an intented behaviour of the controller, handle
it gracefully by parsing that empty packet with packet type 0x00 and
then just simply report it as diagnostic packet.
With that change no errors are logging and the packet itself is actually
recorded in the Bluetooth monitor traces.
< HCI Command: Broadcom Launch RAM (0x3f|0x004e) plen 4
Address: 0xffffffff
> HCI Event: Command Complete (0x0e) plen 4
Broadcom Launch RAM (0x3f|0x004e) ncmd 1
Status: Success (0x00)
= Vendor Diagnostic (len 0)
< HCI Command: Broadcom Update UART Baud Rate (0x3f|0x0018) plen 6
00 00 00 10 0e 00 ......
> HCI Event: Command Complete (0x0e) plen 4
Broadcom Update UART Baud Rate (0x3f|0x0018) ncmd 1
Status: Success (0x00)
< HCI Command: Reset (0x03|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 4
Reset (0x03|0x0003) ncmd 1
Status: Success (0x00)
Signed-off-by: Marcel Holtmann <[email protected]>
Signed-off-by: Johan Hedberg <[email protected]>
|
|
Add basic support for Broadcom serial slave devices.
Probe the serial device, retrieve its maximum speed and
register a new hci uart device.
Tested/compatible with bcm43438 (RPi3).
Signed-off-by: Loic Poulain <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
The commands that read the basic vendor information about the Broadcom
controller are duplicated for UART and USB devices. Combine them into a
single function to reduce the code complexity.
Signed-off-by: Marcel Holtmann <[email protected]>
Signed-off-by: Johan Hedberg <[email protected]>
|
|
Not all Broadcom controller support the 4Mbps operational speed on UART
devices. This is because the UART clock setting changes might not be
supported.
< HCI Command: Broadcom Write UART Clock Setting (0x3f|0x0045) plen 1
01 .
> HCI Event: Command Complete (0x0e) plen 4
Broadcom Write UART Clock Setting (0x3f|0x0045) ncmd 1
Status: Unknown HCI Command (0x01)
To support any operational speed higher than 3Mbps, support for this
command is required. With that respect it is better to not enforce any
operational speed by default. Only when its support is known, then allow
for higher operational speed.
This patch assigns the 4Mbps opertional speed only for devices
discovered through ACPI and leave all others at the default 115200.
Signed-off-by: Marcel Holtmann <[email protected]>
Signed-off-by: Johan Hedberg <[email protected]>
|
|
BT-Controller connected as platform non-root-hub device and
usb-driver initialize such device with wakeup disabled,
Ref. usb_new_device().
At present wakeup-capability get enabled by hid-input device from usb
function driver(e.g. BT HID device) at runtime. Again some functional
driver does not set usb-wakeup capability(e.g LE HID device implement
as HID-over-GATT), and can't wakeup the host on USB.
Most of the device operation (such as mass storage) initiated from host
(except HID) and USB wakeup aligned with host resume procedure. For BT
device, usb-wakeup capability need to enable form btusc driver as a
generic solution for multiple profile use case and required for USB remote
wakeup (in-bus wakeup) while host is suspended. Also usb-wakeup feature
need to enable/disable with HCI interface up and down.
Signed-off-by: Sukumar Ghorai <[email protected]>
Signed-off-by: Amit K Bag <[email protected]>
Acked-by: Oliver Neukum <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
|
|
The GPD Pocket is shipping with a BCM2045 USB HCI with its vendor and
product information set to 0000:0000 and also has its interface class
set to 255 (Vendor Specific Class). Luckily it does advertise usable
manufacturer and product strings.
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM2045A0
S: SerialNumber=AC83F30677CB
C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Reported-by: Christopher Williamson <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
Signed-off-by: Johan Hedberg <[email protected]>
|