| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The PinePhone Pro as SPI flash on board so enable the SPI
interface and the flash.
Signed-off-by: Peter Robinson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
SPI NOR flash chip may vary, so use safe(lowest) spi-max-frequency.
Signed-off-by: FUKAUMI Naoki <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
This commit adds SFC node for Radxa ROCK 5A.
since sdhci and sfc on RK3588s share pins(i.e. exclusive), it cannot
be enabled both nodes at the same time. so status = "okay" is omitted
here.
you may be able to enable sfc (and disable sdhci) by fdt overlay.
SPI NOR flash chip may vary, so use safe(lowest) spi-max-frequency.
Signed-off-by: FUKAUMI Naoki <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
This commit adds support for SPI NOR flash on Radxa ROCK 5B.
SPI NOR flash chip may vary, so use safe(lowest) spi-max-frequency.
Signed-off-by: FUKAUMI Naoki <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
This links the PWM fan on Radxa Rock 5B as an active cooling device
managed automatically by the thermal subsystem, with a target SoC
temperature of 65C and a minimum-spin interval from 55C to 65C to
ensure airflow when the system gets warm
Helped-by: Dragan Simic <[email protected]>
Reviewed-by: Dragan Simic <[email protected]>
Signed-off-by: Alexey Charkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
As the GPU support on RK3588 has been merged upstream, along with OPP
values, add a corresponding cooling map for passive cooling using the GPU.
Signed-off-by: Alexey Charkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
This enables the on-chip thermal monitoring sensor (TSADC) on all
RK3588(s) boards that don't have it enabled yet. It provides temperature
monitoring for the SoC and emergency thermal shutdowns, and is thus
important to have in place before CPU DVFS is enabled, as high CPU
operating performance points can overheat the chip quickly in the
absence of thermal management.
Signed-off-by: Alexey Charkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
This includes the necessary device tree data to allow thermal
monitoring on RK3588(s) using the on-chip TSADC device, along with
trip points for automatic thermal management.
Each of the CPU clusters (one for the little cores and two for
the big cores) get a passive cooling trip point at 85C, which
will trigger DVFS throttling of the respective cluster upon
reaching a high temperature condition.
All zones also have a critical trip point at 115C, which will
trigger a reset.
Signed-off-by: Alexey Charkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
Rename the Rockchip RK3588 SoC dtsi files and, consequently, adjust their
contents appropriately, to prepare them for the ability to specify different
CPU and GPU OPPs for each of the supported RK3588 SoC variants.
As already discussed, [1][2][3][4] some of the RK3588 SoC variants require
different OPPs, and it makes more sense to have the OPPs already defined when
a board dts(i) file includes one of the SoC variant dtsi files (rk3588.dtsi,
rk3588j.dtsi or rk3588s.dtsi), rather than requiring the board dts(i) file
to also include a separate rk3588*-opp.dtsi file. The choice of the SoC
variant is already made by the inclusion of the SoC dtsi file into the board
dts(i) file, and it doesn't make much sense to, effectively, allow the board
dts(i) file to include and use an incompatible set of OPPs for the already
selected RK3588 SoC variant.
The new naming scheme for the RK3588 SoC dtsi files uses "-base" and "-extra"
suffixes to denote the DT data shared between all RK5588 SoC variants, and
the DT data shared between the unrestricted SoC variants, respectively.
For example, the DT data for the RK3588 includes both rk3588-base.dtsi and
rk3588-extra.dtsi, because it's an unrestricted SoC variant, while the DT
data for the RK3588S variant includes rk3588-base.dtsi only, because it's
a restricted SoC variant, feature- and interface-wise. This achieves a more
logical naming of the RK3588 SoC dtsi files, which reflects the way DT data
for the SoC variants is built by "stacking" the SoC variant features made
available through the "-base" and "-extra" SoC dtsi files. Additionally,
the SoC variant dtsi files (rk3588.dtsi, rk3588j.dtsi and rk3588s.dtsi) are
no longer parents to any other SoC variant dtsi files, which should help with
making the new "stacking" approach cleaner and easier to follow.
The RK3588 pinctrl dtsi files are also renamed in the same way, for the sake
of consistency. This also keeps the "-base" and "-extra" groups of the dtsi
files together when looked at in a directory listing, which is helpful.
The per-SoC-variant OPPs should go directly into the SoC dtsi files, if no
more than one SoC variant uses those OPPs, or be put into a separate "-opp"
dtsi file that's shared between and included from two or more SoC variant
dtsi files. An example for the former is the non-shared OPP data that should
go directly into the RK3588J SoC variant dtsi file (i.e. rk3588j.dtsi), and
an example for the latter is the shared OPP data that should be put into
rk3588-opp.dtsi and be included from the RK3588 and RK3588S SoC variant dtsi
files (i.e. rk3588.dtsi and rk3588s.dtsi, respectively). Consequently, if
the OPPs for the RK3588 and RK3588S SoC variants are ever made different,
the shared rk3588-opp.dtsi file should be deleted and the new OPPs should
be put directly into rk3588.dtsi and rk3588s.dtsi. [4]
No functional changes are introduced, which was validated by decompiling and
comparing all affected dtb files before and after these changes.
As a side note, due to the nature of introduced changes, this commit is best
viewed using the --break-rewrites option for git-log(1).
[1] https://lore.kernel.org/linux-rockchip/[email protected]/
[2] https://lore.kernel.org/linux-rockchip/CABjd4Yxi=+3gkNnH3BysUzzYsji-=-yROtzEc8jM_g0roKB0-w@mail.gmail.com/
[3] https://lore.kernel.org/linux-rockchip/[email protected]/
[4] https://lore.kernel.org/linux-rockchip/673dcf47596e7bc8ba065034e339bb1bbf9cdcb0.1716948159.git.dsimic@manjaro.org/T/#u
Signed-off-by: Dragan Simic <[email protected]>
Link: https://lore.kernel.org/r/9ffedc0e2ca7f167d9d795b2a8f43cb9f56a653b.1717923308.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
The CM3588 NAS by FriendlyElec pairs the CM3588 compute module, based on
the Rockchip RK3588 SoC, with the CM3588 NAS Kit carrier board.
To reflect the hardware setup, add device tree sources for the SoM and
the NAS daughter board as separate files.
Hardware features:
- Rockchip RK3588 SoC
- 4GB/8GB/16GB LPDDR4x RAM
- 64GB eMMC
- MicroSD card slot
- 1x RTL8125B 2.5G Ethernet
- 4x M.2 M-Key with PCIe 3.0 x1 (via bifurcation) for NVMe SSDs
- 2x USB 3.0 (USB 3.1 Gen1) Type-A, 1x USB 2.0 Type-A
- 1x USB 3.0 Type-C with DP AltMode support
- 2x HDMI 2.1 out, 1x HDMI in
- MIPI-CSI Connector, MIPI-DSI Connector
- 40-pin GPIO header
- 4 buttons: power, reset, recovery, MASK, user button
- 3.5mm Headphone out, 2.0mm PH-2A Mic in
- 5V Fan connector, PWM beeper, IR receiver, RTC battery connector
PCIe bifurcation is used to handle all four M.2 sockets at PCIe 3.0 x1
speed. Data lane mapping in the DT is done like described in commit
f8020dfb311d ("phy: rockchip-snps-pcie3: fix bifurcation on rk3588").
This device tree includes support for eMMC, SD card, ethernet, all USB2
and USB3 ports, all four M.2 slots, GPU, beeper, IR, RTC, UART debugging
as well as the buttons and LEDs.
The GPIOs are labeled according to the schematics.
Reviewed-by: Space Meyer <[email protected]>
Signed-off-by: Sebastian Kropatsch <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
Enable the hdmi_sound node and add i2s0 as sound source
for mk808 hdmi.
Signed-off-by: Johan Jonker <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
Add the missing #sound-dai-cells for RK3368's I2S and S/PDIF controllers.
Fixes: f7d89dfe1e31 ("arm64: dts: rockchip: add i2s nodes support for RK3368 SoCs")
Fixes: 0328d68ea76d ("arm64: dts: rockchip: add rk3368 spdif node")
Signed-off-by: Alex Bee <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
According to the hardware design, the i2c address of audio codec es8316
on Cool Pi 4B is 0x10.
This fix the read/write error like bellow:
es8316 7-0011: ASoC: error at soc_component_write_no_lock on es8316.7-0011 for register: [0x0000000c] -6
es8316 7-0011: ASoC: error at soc_component_write_no_lock on es8316.7-0011 for register: [0x00000003] -6
es8316 7-0011: ASoC: error at soc_component_read_no_lock on es8316.7-0011 for register: [0x00000016] -6
es8316 7-0011: ASoC: error at soc_component_read_no_lock on es8316.7-0011 for register: [0x00000016] -6
Fixes: 3f5d336d64d6 ("arm64: dts: rockchip: Add support for rk3588s based board Cool Pi 4B")
Signed-off-by: Andy Yan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
Add the core reset for uarts, which is necessary for uarts to work.
Signed-off-by: Hal Feng <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
In the attempt to clear and recreate the initial ID map for LPA2, we
wrongly use 'start - end' as the map size and make the memset() almost a
nop.
Fix it by passing the correct map size.
Fixes: 9684ec186f8f ("arm64: Enable LPA2 at boot if supported by the system")
Signed-off-by: Zenghui Yu <[email protected]>
Reviewed-by: Ard Biesheuvel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
On some devicetrees, the drive-strength property gets assigned a
MTK_DRIVE_(x)_mA definition, which matches with (x).
For example, MTK_DRIVE_8mA equals to 8 and MTK_DRIVE_30mA equals
to 30.
Also keeping in mind that the drive-strength property is, by
(binding) definition, taking a number in milliamperes unit,
change all devicetrees to avoid the usage of any MTK_DRIVE_(x)
definition.
Reviewed-by: Chen-Yu Tsai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: AngeloGioacchino Del Regno <[email protected]>
|
|
With ARCH=m68k, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in arch/m68k/emu/nfblock.o
WARNING: modpost: missing MODULE_DESCRIPTION() in arch/m68k/emu/nfcon.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
[geert: s/ARAnyM/Atari NatFeat/]
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
Fixes the following:
thermal-zones: 'soc_thermal' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/thermal/thermal-zones.yaml#
Fixes: 593ab951232b ("arm64: dts: amlogic: ad402: setup thermal-zones")
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/20240624-topic-amlogic-upstream-bindings-fixes-dts-round-2-v1-1-0a21f456eb8d@linaro.org
Signed-off-by: Neil Armstrong <[email protected]>
|
|
On s390, zero page's size relies on total ram pages.
Since we plan to move the accounting into __free_pages_core(),
totalram_pages may not represent the total usable pages on system
at this point when defer_init is enabled.
We can get the total usable pages from memblock directly. The size maybe
not accurate due to the alignment, but enough for the calculation.
Signed-off-by: Wei Yang <[email protected]>
CC: Mike Rapoport (IBM) <[email protected]>
CC: David Hildenbrand <[email protected]>
Reviewed-by: David Hildenbrand <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vasily Gorbik <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
Make use of the popcnt instruction to provide optimized __arch_hweight*()
implementations. The generated code is shorter and avoids rather expensive
functions calls.
Acked-by: Alexander Gordeev <[email protected]>
Signed-off-by: Heiko Carstens <[email protected]>
Signed-off-by: Alexander Gordeev <[email protected]>
|
|
Dreambox One and Dreambox Two are based on the Amlogic W400 reference
board with an S922X chip and the following specs:
- 2GB DDR3 RAM
- 16GB eMMC
- 10/100/1000 Base-T Ethernet
- AP6356 Wireless (802.11 b/g/n/ac, BT 5.0)
- HDMI 2.1 video
- S/PDIF optical output
- 2x DVB-S2/T2
- Smartcard Reader Slot
- 2x USB 2.0 port (1x micro-USB for service)
- 1x USB 3.0 port
- IR receiver
- 1x Power LED (blue)
- 1x Power button (top)
- 1x Update/Reset button (underside)
- 1x micro SD card slot
Dreambox Two differences:
- 3" Colour LCD display (MIPI-DSI)
- Common Interface Slot
Signed-off-by: Christian Hewitt <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
|
|
The OSMC Vero 4K device is based on the Amlogic S905X (P212)
reference design with the following specifications:
- 2GB DDR4 RAM
- 16GB eMMC
- HDMI 2.1 video
- S/PDIF optical output
- AV output
- 10/100 Ethernet
- AP6255 Wireless (802.11 a/b/g/n/ac, BT 4.2)
- 2x USB 2.0 ports (1x OTG)
- IR receiver (internal)
- IR extender port (external)
- 1x micro SD card slot
- 1x Power LED (red)
- 1x Reset button (in AV jack)
Signed-off-by: Christian Hewitt <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
|
|
In a TDX VM without paravisor, currently the default timer is the Hyper-V
timer, which depends on the slow VM Reference Counter MSR: the Hyper-V TSC
page is not enabled in such a VM because the VM uses Invariant TSC as a
better clocksource and it's challenging to mark the Hyper-V TSC page shared
in very early boot.
Lower the rating of the Hyper-V timer so the local APIC timer becomes the
the default timer in such a VM, and print a warning in case Invariant TSC
is unavailable in such a VM. This change should cause no perceivable
performance difference.
Cc: [email protected] # 6.6+
Reviewed-by: Roman Kisel <[email protected]>
Signed-off-by: Dexuan Cui <[email protected]>
Reviewed-by: Michael Kelley <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Wei Liu <[email protected]>
Message-ID: <[email protected]>
|
|
Drop auto-selecting the driver, so it can be built either as a
module or built-in.
Signed-off-by: Antonio Borneo <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Drop auto-selecting the driver, so it can be built either as a module or
built-in.
Signed-off-by: Antonio Borneo <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add a 20MB reserved memory region for use by SCM calls.
Signed-off-by: Bartosz Golaszewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
Enable SHM Bridge support in the Qualcomm TrustZone allocator by default
as even on architectures that don't support it, we automatically fall
back to the generic allocator.
Signed-off-by: Bartosz Golaszewski <[email protected]>
Tested-by: Andrew Halaney <[email protected]> # sc8280xp-lenovo-thinkpad-x13s
Tested-by: Deepti Jaggi <[email protected]> #sa8775p-ride
Reviewed-by: Elliot Berman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
With the smsm bindings and driver finally supporting mboxes, switch to
that and stop using apcs as syscon.
Signed-off-by: Luca Weiss <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
With the smsm bindings and driver finally supporting mboxes, switch to
that and stop using apcs as syscon.
Signed-off-by: Luca Weiss <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
With the smsm bindings and driver finally supporting mboxes, switch to
that and stop using apcs as syscon.
Signed-off-by: Luca Weiss <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
With the smsm bindings and driver finally supporting mboxes, switch to
that and stop using apcs as syscon.
Signed-off-by: Luca Weiss <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
With the smsm bindings and driver finally supporting mboxes, switch to
that and stop using apcs as syscon.
Signed-off-by: Luca Weiss <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
Add tsens and thermal zones nodes for x1e80100 SoC.
Signed-off-by: Rajendra Nayak <[email protected]>
Signed-off-by: Abel Vesa <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Tested-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
PM8008 regulators are used for the cameras found on FP5. Configure the
chip and its voltages.
Signed-off-by: Luca Weiss <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
PM8008 regulators are used for the cameras found on FP4. Configure the
chip and its voltages.
Signed-off-by: Luca Weiss <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
There is PM8916 Battery voltage monitor on GPLUS FL8005A.
Add PM8916 BMS and the battery to the device tree.
Signed-off-by: Lin, Meng-Bo <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
SD cards would exhibit errors similar to ones described in commit
27fe0fc05f35 ("ARM: dts: msm8974-FP2: Increase load on l20 for sdhci")
This patch applies the same change to the regulator for sdhc2.
Signed-off-by: Valeriy Klimin <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
Add the dts for the Z3 Compact. This is currently almost the same
as the plain Z3 as they share almost the same hardware and
nothing device-specific is currently supported.
Signed-off-by: Valeriy Klimin <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
Add the Serial Flash Controller and it's pincontrols.
Signed-off-by: Alex Bee <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
[reference HCLK_SFC by its numeric id to prevent conflicts with the
clock binding/controller changes]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
Use recommended generic node names for the Adreno GPU and QFPROM fused
values device nodes.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
Add hdmi-sound node to rk3066a.dtsi, so that it
can be reused by boards with HDMI support.
Signed-off-by: Johan Jonker <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
The SoC has a S/PDIF TX controller which is fully compatible with older
generation Rockchip SoCs.
Signed-off-by: Alex Bee <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
RK3128 SoCs have two i2s controllers. i2s_8ch has 8 tx and 2 rx channels
and is internally hard-wired to the hdmi-controller respectivly the SoC's
analog codec. i2s_2ch has 2 tx and 2 rx channels and can also be used
externally as it's pins are exposed though pinctrl.
Signed-off-by: Alex Bee <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
Add the Designware MIPI DSI controller and it's port nodes.
Signed-off-by: Alex Bee <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
The InnoSilicon D-PHY found in RK3128 SoCs supports DSI/LVDS/TTL with a
maximum transfer rate of 1 Gbps per lane. While adding it, also add it's
clocks to RK3128_PD_VIO powerdomain as the phy is part of it.
Signed-off-by: Alex Bee <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
Use the new config flag to build the correct driver that will be
extracted from the old code.
Signed-off-by: Antonio Borneo <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Build the proper driver by selecting the appropriate config flag.
Signed-off-by: Antonio Borneo <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Introduce the advanced extended interrupt controllers. This feature will
allow each core to have 256 independent interrupt vectors and MSI
interrupts can be independently routed to any vector on any CPU.
[ tglx: Fixed up coding style. Made on/offline functions void ]
Co-developed-by: Jianmin Lv <[email protected]>
Signed-off-by: Jianmin Lv <[email protected]>
Co-developed-by: Liupu Wang <[email protected]>
Signed-off-by: Liupu Wang <[email protected]>
Signed-off-by: Tianyang Zhang <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
- fix lseek in o32 compat mode
- fix for microMIPS MT ASE helpers
* tag 'mips-fixes_6.10_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
mips: fix compat_sys_lseek syscall
MIPS: mipsmtregs: Fix target register for MFTC0
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- An ARM-relevant fix to not free default RMIDs of a resource control
group
- A randconfig build fix for the VMware virtual GPU driver
* tag 'x86_urgent_for_v6.10_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/resctrl: Don't try to free nonexistent RMIDs
drm/vmwgfx: Fix missing HYPERVISOR_GUEST dependency
|