| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The RTC module on the A23 was claimed to be the same as on the A31, when
in fact it is not. The A31 does not have an RTC external clock output,
and its internal RC oscillator's average clock rate is not in the same
range. The A33's RTC is the same as the A23.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The register range is also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The R40 datasheet specifies a tolerance range for the external
oscillators used. Add them to the device tree as the clock accuracy.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The H3 datasheet specifies a tolerance range for the external
oscillators used. Add them to the device tree as the clock accuracy.
The internal oscillator is left unchanged, as it will be removed later.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The current oversampling rate of 512 means that for 48 kHz 16 bit
stereo, the MCLK is running at the same rate as the module clock,
so there is no head room to support higher sampling rates. The codec
however supports up to 192 kHz for playback.
This patch drops the oversampling rate from 512 to 128, so that 192 kHz
audio can be played back directly without downsampling. Ideally we
should be using different oversampling rates for different sampling
rates, but that's not possible without a platform-specific machine
driver.
Fixes: 870f1bd1f5e9 ("ARM: dts: sun8i: Add audio codec, dai and card for A33")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Just like on the A33, the video engine on the H3 can map any address in
memory, so there is no particular need to have reserved memory at a fixed
address.
As a result, remove the reserved memory node and let the kernel allocate
the CMA pool wherever it sees fit.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
While we believed that the memory for the video engine had to be kept
in the first 256 MiBs of DRAM, this is no longer true starting with the
A33 and any address can be mapped.
As a result, remove the reserved memory node and let the kernel allocate
the CMA pool wherever it sees fit.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Lichee Pi Nano is a F1C100s board by Lichee Pi.
Add initial device tree for it.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
F1C100s is one product with the suniv die, which has a 32MiB co-packaged
DDR1 DRAM chip. As we have the support for suniv pin controller and CCU now, add a
initial DTSI for it.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Add AC power supply subnode for AXP81X PMIC.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Our memory node will generate a warning in DTC since the unit address is
not matching the reg property. However, that node will be created by the
bootloader, so we can just remove it entirely in order to remove that
warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The MMC0 controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Most of our device trees have had leading zeros for padding as part of
the nodes unit-addresses.
Remove all these useless zeros that generate warnings
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The i2c nodes were pre-populated to ease the use of overlays. However, now
that we provide default muxing options for those nodes, the one in the DTS
don't provide any content at all.
Remove them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The I2C's and MMC0 controllers have only one muxing option in the SoC. In
such a case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Now that all the SoCs using the tablet reference design DTSI are using the
same pinctrl naming scheme, we can move back the pinctrl phandles to the
main DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.
This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The pin groups are supposed to be in alphabetical order, and they aren't.
Fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some boards override the MMC pin muxing settings in order to enable the
pull-ups and change the drive strength to a value higher than the default.
While this was needed in the earlier days, this is now the default setting
for those pins, and therefore we don't need those board-specific settings
anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.
Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Most of our device trees have had leading zeros for padding as part of
the nodes unit-addresses.
Remove all these useless zeros that generate warnings
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The #address-cells and #size-cells are only relevant for nodes that have
childs with reg properties. Otherwise, DTC will emit a warning saying that
those properties are unnecessary.
Remove them when needed.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
DTC will emit a warning on our OPPs nodes for the common DTSI between the
A23 and A33 since those nodes use the frequency as unit addresses, but
don't have a matching reg property.
Fix this by moving the frequency to the node name instead.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.
Remove it in order to remove those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The #address-cells and #size-cells are only relevant for nodes that have
childs with reg properties. Otherwise, DTC will emit a warning saying that
those properties are unnecessary.
Remove them when needed.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some boards override the MMC pin muxing settings in order to enable the
pull-ups and change the drive strength to a value higher than the default.
While this was needed in the earlier days, this is now the default setting
for those pins, and therefore we don't need those board-specific settings
anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The I2C and MMC controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Our HDMI output endpoint on the A10s DTSI has a warning under DTC: "graph
node has single child node 'endpoint', #address-cells/#size-cells are not
necessary". Fix this by removing those properties.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The SOM204-EVB doesn't use the CTS pin, and thus was defining its own
pinctrl node for the UART3 muxing. Since we split away the TX and RX pin,
we can use the global node now, and only have the RTS pin in our local
node.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some UART nodes on the A20 DTSI do not share the same pattern that we use
everywhere else, with the RTS and CTS pins split away from the TX and RX
pins. Make those pin groups consistent with the rest of our DT.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some gpio-keys definitions in our DTs were having buttons defined with a
unit-address and that would generate a DTC warning.
Change the buttons node names to remove the warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.
This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.
Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Our oscillators clock names have a unit address, but no reg property, which
generates a warning in DTC. Change these names to remove those unit
addresses.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.
Remove it in order to remove those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The I2C and MMC controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Our I2C GPIO bus node name has a unit address, but no reg property, which
generates a warning in DTC. Change the name to remove that unit address.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|