| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 6.10:
- Fix GPIO number for reg_usdhc2_vmmc on imx8qm-mek board.
- Enable hysteresis for SODIMM_17 pin on imx8mm-verdin board to increase
immunity against noise.
- Remove 'no-sdio' property for uSDHC2 on imx93-11x11-evk board, so that
SDIO cards could also work.
- Fix BT shutdown GPIO for imx8mp-venice-gw73xx-2x board.
- Fix panel node deleting on imx53-qsb-hdmi, as /delete-node/ directive
doesn't really delete a node in a DT overlay.
- Fix TC9595 input clock on DH i.MX8M Plus DHCOM SoM.
- Fix GPU speed for imx8mm-verdin board by enabling overdrive mode in
the SOM dtsi.
* tag 'imx-fixes-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8qm-mek: fix gpio number for reg_usdhc2_vmmc
arm64: dts: freescale: imx8mm-verdin: enable hysteresis on slow input pin
arm64: dts: imx93-11x11-evk: Remove the 'no-sdio' property
arm64: dts: freescale: imx8mp-venice-gw73xx-2x: fix BT shutdown GPIO
arm: dts: imx53-qsb-hdmi: Disable panel instead of deleting node
arm64: dts: imx8mp: Fix TC9595 input clock on DH i.MX8M Plus DHCOM SoM
arm64: dts: freescale: imx8mm-verdin: Fix GPU speed
Link: https://lore.kernel.org/r/Zm+xVUmFtaOnYBb4@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Sync pending posted interrupts to the IRR prior to re-scanning I/O APIC
routes, irrespective of whether the I/O APIC is emulated by userspace or
by KVM. If a level-triggered interrupt routed through the I/O APIC is
pending or in-service for a vCPU, KVM needs to intercept EOIs on said
vCPU even if the vCPU isn't the destination for the new routing, e.g. if
servicing an interrupt using the old routing races with I/O APIC
reconfiguration.
Commit fceb3a36c29a ("KVM: x86: ioapic: Fix level-triggered EOI and
userspace I/OAPIC reconfigure race") fixed the common cases, but
kvm_apic_pending_eoi() only checks if an interrupt is in the local
APIC's IRR or ISR, i.e. misses the uncommon case where an interrupt is
pending in the PIR.
Failure to intercept EOI can manifest as guest hangs with Windows 11 if
the guest uses the RTC as its timekeeping source, e.g. if the VMM doesn't
expose a more modern form of time to the guest.
Cc: stable@vger.kernel.org
Cc: Adamos Ttofari <attofari@amazon.de>
Cc: Raghavendra Rao Ananta <rananta@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240611014845.82795-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
- fix for BCM6538 boards
- fix RB532 PCI workaround
* tag 'mips-fixes_6.10_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
Revert "MIPS: pci: lantiq: restore reset gpio polarity"
mips: bmips: BCM6358: make sure CBR is correctly set
MIPS: pci: lantiq: restore reset gpio polarity
MIPS: Routerboard 532: Fix vendor retry check code
|
|
Previously pgattr_change_is_safe() was overly-strict and complained
(e.g. "[ 116.262743] __check_safe_pte_update: unsafe attribute change:
0x0560000043768fc3 -> 0x0160000043768fc3") if it saw any SW bits change
in a live PTE. There is no such restriction on SW bits in the Arm ARM.
Until now, no SW bits have been updated in live mappings via the
set_ptes() route. PTE_DIRTY would be updated live, but this is handled
by ptep_set_access_flags() which does not call pgattr_change_is_safe().
However, with the introduction of uffd-wp for arm64, there is core-mm
code that does ptep_get(); pte_clear_uffd_wp(); set_ptes(); which
triggers this false warning.
Silence this warning by masking out the SW bits during checks.
The bug isn't technically in the highlighted commit below, but that's
where bisecting would likely lead as its what made the bug user-visible.
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Fixes: 5b32510af77b ("arm64/mm: Add uffd write-protect support")
Link: https://lore.kernel.org/r/20240619121859.4153966-1-ryan.roberts@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Commit
6791e0ea3071 ("x86/resctrl: Access per-rmid structures by index")
adds logic to map individual monitoring groups into a global index space used
for tracking allocated RMIDs.
Attempts to free the default RMID are ignored in free_rmid(), and this works
fine on x86.
With arm64 MPAM, there is a latent bug here however: on platforms with no
monitors exposed through resctrl, each control group still gets a different
monitoring group ID as seen by the hardware, since the CLOSID always forms part
of the monitoring group ID.
This means that when removing a control group, the code may try to free this
group's default monitoring group RMID for real. If there are no monitors
however, the RMID tracking table rmid_ptrs[] would be a waste of memory and is
never allocated, leading to a splat when free_rmid() tries to dereference the
table.
One option would be to treat RMID 0 as special for every CLOSID, but this would
be ugly since bookkeeping still needs to be done for these monitoring group IDs
when there are monitors present in the hardware.
Instead, add a gating check of resctrl_arch_mon_capable() in free_rmid(), and
just do nothing if the hardware doesn't have monitors.
This fix mirrors the gating checks already present in
mkdir_rdt_prepare_rmid_alloc() and elsewhere.
No functional change on x86.
[ bp: Massage commit message. ]
Fixes: 6791e0ea3071 ("x86/resctrl: Access per-rmid structures by index")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://lore.kernel.org/r/20240618140152.83154-1-Dave.Martin@arm.com
|
|
Milkv Duo does not have a write-protect pin, so disable write protect
to prevent SDcards misdetected as read-only.
Fixes: 89a7056ed4f7 ("riscv: dts: sophgo: add sdcard support for milkv duo")
Signed-off-by: Haylen Chu <heylenay@outlook.com>
Link: https://lore.kernel.org/r/SEYPR01MB4221943C7B101DD2318DA0D3D7CE2@SEYPR01MB4221.apcprd01.prod.exchangelabs.com
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
"Another small set of EFI fixes. Only the x86 one is likely to affect
any actual users (and has a cc:stable), but the issue it fixes was
only observed in an unusual context (kexec in a confidential VM).
- Ensure that EFI runtime services are not unmapped by PAN on ARM
- Avoid freeing the memory holding the EFI memory map inadvertently
on x86
- Avoid a false positive kmemleak warning on arm64"
* tag 'efi-fixes-for-v6.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi/arm64: Fix kmemleak false positive in arm64_efi_rt_init()
efi/x86: Free EFI memory map only when installing a new one.
efi/arm: Disable LPAE PAN when calling EFI runtime services
|
|
mmap_base by default"
This reverts commit 3afb76a66b5559a7b595155803ce23801558a7a9.
This was a wrongheaded workaround for an issue that had already been
fixed much better by commit 4ef9ad19e176 ("mm: huge_memory: don't force
huge page alignment on 32 bit").
Asking users questions at kernel compile time that they can't make sense
of is not a viable strategy. And the fact that even the kernel VM
maintainers apparently didn't catch that this "fix" is not a fix any
more pretty much proves the point that people can't be expected to
understand the implications of the question.
It may well be the case that we could improve things further, and that
__thp_get_unmapped_area() should take the mapping randomization into
account even for 64-bit kernels. Maybe we should not be so eager to use
THP mappings.
But in no case should this be a kernel config option.
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In commit 4e4dc65ab578 ("s390/pci: use phys_to_virt() for AIBVs/DIBVs")
the setting of dibv_addr was missed when adding virt_to_phys(). This
only affects systems with directed interrupt delivery enabled which are
not generally available.
Fixes: 4e4dc65ab578 ("s390/pci: use phys_to_virt() for AIBVs/DIBVs")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"Mainly MM singleton fixes. And a couple of ocfs2 regression fixes"
* tag 'mm-hotfixes-stable-2024-06-17-11-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
kcov: don't lose track of remote references during softirqs
mm: shmem: fix getting incorrect lruvec when replacing a shmem folio
mm/debug_vm_pgtable: drop RANDOM_ORVALUE trick
mm: fix possible OOB in numa_rebuild_large_mapping()
mm/migrate: fix kernel BUG at mm/compaction.c:2761!
selftests: mm: make map_fixed_noreplace test names stable
mm/memfd: add documentation for MFD_NOEXEC_SEAL MFD_EXEC
mm: mmap: allow for the maximum number of bits for randomizing mmap_base by default
gcov: add support for GCC 14
zap_pid_ns_processes: clear TIF_NOTIFY_SIGNAL along with TIF_SIGPENDING
mm: huge_memory: fix misused mapping_large_folio_support() for anon folios
lib/alloc_tag: fix RCU imbalance in pgalloc_tag_get()
lib/alloc_tag: do not register sysctl interface when CONFIG_SYSCTL=n
MAINTAINERS: remove Lorenzo as vmalloc reviewer
Revert "mm: init_mlocked_on_free_v3"
mm/page_table_check: fix crash on ZONE_DEVICE
gcc: disable '-Warray-bounds' for gcc-9
ocfs2: fix NULL pointer dereference in ocfs2_abort_trigger()
ocfs2: fix NULL pointer dereference in ocfs2_journal_dirty()
|
|
The gpio in "reg_usdhc2_vmmc" should be 7 instead of 19.
Cc: stable@vger.kernel.org
Fixes: 307fd14d4b14 ("arm64: dts: imx: add imx8qm mek support")
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"On parisc we have suffered since years from random segfaults which
seem to have been triggered due to cache inconsistencies. Those
segfaults happened more often on machines with PA8800 and PA8900 CPUs,
which have much bigger caches than the earlier machines.
Dave Anglin has worked over the last few weeks to fix this bug. His
patch has been successfully tested by various people on various
machines and with various kernels (6.6, 6.8 and 6.9), and the debian
buildd servers haven't shown a single random segfault with this patch.
Since the cache handling has been reworked, the patch is slightly
bigger than I would like in this stage, but the greatly improved
stability IMHO justifies the inclusion now"
* tag 'parisc-for-6.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Try to fix random segmentation faults in package builds
|
|
SODIMM 17 can be used as an edge triggered interrupt supplied from an
off board source.
Enable hysteresis on the pinmuxing to increase immunity against noise
on the signal.
Fixes: 60f01b5b5c7d ("arm64: dts: imx8mm-verdin: update iomux configuration")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The usdhc2 port is connected to the microSD slot. The presence of the
'no-sdio' property prevents Wifi SDIO cards, such as CMP9010-X-EVB [1]
to be detected.
Remove the 'no-sdio' property so that SDIO cards could also work.
[1] https://www.nxp.com/products/wireless-connectivity/wi-fi-plus-bluetooth-plus-802-15-4/cmp9010-x-evb-iw416-usd-interface-evaluation-board:CMP9010-X-EVB
Fixes: e37907bd8294 ("arm64: dts: freescale: add i.MX93 11x11 EVK basic support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Al reported a possible use-after-free (UAF) in kvm_spapr_tce_attach_iommu_group().
It looks up `stt` from tablefd, but then continues to use it after doing
fdput() on the returned fd. After the fdput() the tablefd is free to be
closed by another thread. The close calls kvm_spapr_tce_release() and
then release_spapr_tce_table() (via call_rcu()) which frees `stt`.
Although there are calls to rcu_read_lock() in
kvm_spapr_tce_attach_iommu_group() they are not sufficient to prevent
the UAF, because `stt` is used outside the locked regions.
With an artifcial delay after the fdput() and a userspace program which
triggers the race, KASAN detects the UAF:
BUG: KASAN: slab-use-after-free in kvm_spapr_tce_attach_iommu_group+0x298/0x720 [kvm]
Read of size 4 at addr c000200027552c30 by task kvm-vfio/2505
CPU: 54 PID: 2505 Comm: kvm-vfio Not tainted 6.10.0-rc3-next-20240612-dirty #1
Hardware name: 8335-GTH POWER9 0x4e1202 opal:skiboot-v6.5.3-35-g1851b2a06 PowerNV
Call Trace:
dump_stack_lvl+0xb4/0x108 (unreliable)
print_report+0x2b4/0x6ec
kasan_report+0x118/0x2b0
__asan_load4+0xb8/0xd0
kvm_spapr_tce_attach_iommu_group+0x298/0x720 [kvm]
kvm_vfio_set_attr+0x524/0xac0 [kvm]
kvm_device_ioctl+0x144/0x240 [kvm]
sys_ioctl+0x62c/0x1810
system_call_exception+0x190/0x440
system_call_vectored_common+0x15c/0x2ec
...
Freed by task 0:
...
kfree+0xec/0x3e0
release_spapr_tce_table+0xd4/0x11c [kvm]
rcu_core+0x568/0x16a0
handle_softirqs+0x23c/0x920
do_softirq_own_stack+0x6c/0x90
do_softirq_own_stack+0x58/0x90
__irq_exit_rcu+0x218/0x2d0
irq_exit+0x30/0x80
arch_local_irq_restore+0x128/0x230
arch_local_irq_enable+0x1c/0x30
cpuidle_enter_state+0x134/0x5cc
cpuidle_enter+0x6c/0xb0
call_cpuidle+0x7c/0x100
do_idle+0x394/0x410
cpu_startup_entry+0x60/0x70
start_secondary+0x3fc/0x410
start_secondary_prolog+0x10/0x14
Fix it by delaying the fdput() until `stt` is no longer in use, which
is effectively the entire function. To keep the patch minimal add a call
to fdput() at each of the existing return paths. Future work can convert
the function to goto or __cleanup style cleanup.
With the fix in place the test case no longer triggers the UAF.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Closes: https://lore.kernel.org/all/20240610024437.GA1464458@ZenIV/
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240614122910.3499489-1-mpe@ellerman.id.au
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- Fix the 8 bytes get_user() logic on x86-32
- Fix build bug that creates weird & mistaken target directory under
arch/x86/
* tag 'x86-urgent-2024-06-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Don't add the EFI stub to targets, again
x86/uaccess: Fix missed zeroing of ia32 u64 get_user() range checking
|
|
default
An ASLR regression was noticed [1] and tracked down to file-mapped areas
being backed by THP in recent kernels. The 21-bit alignment constraint
for such mappings reduces the entropy for randomizing the placement of
64-bit library mappings and breaks ASLR completely for 32-bit libraries.
The reported issue is easily addressed by increasing vm.mmap_rnd_bits and
vm.mmap_rnd_compat_bits. This patch just provides a simple way to set
ARCH_MMAP_RND_BITS and ARCH_MMAP_RND_COMPAT_BITS to their maximum values
allowed by the architecture at build time.
[1] https://zolutal.github.io/aslrnt/
[akpm@linux-foundation.org: default to `y' if 32-bit, per Rafael]
Link: https://lkml.kernel.org/r/20240606180622.102099-1-aquini@redhat.com
Fixes: 1854bc6e2420 ("mm/readahead: Align file mappings for non-DAX")
Signed-off-by: Rafael Aquini <aquini@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Samuel Holland <samuel.holland@sifive.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Fix the invalid BT shutdown GPIO (gpio1_io3 not gpio4_io16)
Fixes: 716ced308234 ("arm64: dts: freescale: Add imx8mp-venice-gw73xx-2x")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The kmemleak code sometimes complains about the following leak:
unreferenced object 0xffff8000102e0000 (size 32768):
comm "swapper/0", pid 1, jiffies 4294937323 (age 71.240s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000db9a88a3>] __vmalloc_node_range+0x324/0x450
[<00000000ff8903a4>] __vmalloc_node+0x90/0xd0
[<000000001a06634f>] arm64_efi_rt_init+0x64/0xdc
[<0000000007826a8d>] do_one_initcall+0x178/0xac0
[<0000000054a87017>] do_initcalls+0x190/0x1d0
[<00000000308092d0>] kernel_init_freeable+0x2c0/0x2f0
[<000000003e7b99e0>] kernel_init+0x28/0x14c
[<000000002246af5b>] ret_from_fork+0x10/0x20
The memory object in this case is for efi_rt_stack_top and is allocated
in an initcall. So this is certainly a false positive. Mark the object
as not a leak to quash it.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
The logic in __efi_memmap_init() is shared between two different
execution flows:
- mapping the EFI memory map early or late into the kernel VA space, so
that its entries can be accessed;
- the x86 specific cloning of the EFI memory map in order to insert new
entries that are created as a result of making a memory reservation
via a call to efi_mem_reserve().
In the former case, the underlying memory containing the kernel's view
of the EFI memory map (which may be heavily modified by the kernel
itself on x86) is not modified at all, and the only thing that changes
is the virtual mapping of this memory, which is different between early
and late boot.
In the latter case, an entirely new allocation is created that carries a
new, updated version of the kernel's view of the EFI memory map. When
installing this new version, the old version will no longer be
referenced, and if the memory was allocated by the kernel, it will leak
unless it gets freed.
The logic that implements this freeing currently lives on the code path
that is shared between these two use cases, but it should only apply to
the latter. So move it to the correct spot.
While at it, drop the dummy definition for non-x86 architectures, as
that is no longer needed.
Cc: <stable@vger.kernel.org>
Fixes: f0ef6523475f ("efi: Fix efi_memmap_alloc() leaks")
Tested-by: Ashish Kalra <Ashish.Kalra@amd.com>
Link: https://lore.kernel.org/all/36ad5079-4326-45ed-85f6-928ff76483d3@amd.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
EFI runtime services are remapped into the lower 1 GiB of virtual
address space at boot, so they are guaranteed to be able to co-exist
with the kernel virtual mappings without the need to allocate space for
them in the kernel's vmalloc region, which is rather small.
This means those mappings are covered by TTBR0 when LPAE PAN is enabled,
and so 'user' access must be enabled while such calls are in progress.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
We cannot use /delete-node/ directive to delete a node in a DT
overlay. The node won't be deleted effectively. Instead, set
the node's status property to "disabled" to achieve something
similar.
Fixes: eeb403df953f ("ARM: dts: imx53-qsb: add support for the HDMI expander")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The IMX8MP_CLK_CLKOUT2 supplies the TC9595 bridge with 13 MHz reference
clock. The IMX8MP_CLK_CLKOUT2 is supplied from IMX8MP_AUDIO_PLL2_OUT.
The IMX8MP_CLK_CLKOUT2 operates only as a power-of-two divider, and the
current 156 MHz is not power-of-two divisible to achieve 13 MHz.
To achieve 13 MHz output from IMX8MP_CLK_CLKOUT2, set IMX8MP_AUDIO_PLL2_OUT
to 208 MHz, because 208 MHz / 16 = 13 MHz.
Fixes: 20d0b83e712b ("arm64: dts: imx8mp: Add TC9595 bridge on DH electronics i.MX8M Plus DHCOM")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- A couple of fixes for regressions resulting from the uncoupling of
physical vs virtual kernel address spaces: fix the mapping of the
kernel image using large pages; enforce alignment checks on physical
addresses before creating large pages
- Update defconfigs
* tag 's390-6.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: Restore mapping of kernel image using large pages
s390/mm: Allow large pages only for aligned physical addresses
s390: Update defconfigs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock
Pull memblock fixes from Mike Rapoport:
"Fix validation of NUMA coverage.
memblock_validate_numa_coverage() was checking for a unset node ID
using NUMA_NO_NODE, but x86 used MAX_NUMNODES when no node ID was
specified by buggy firmware.
Update memblock to substitute MAX_NUMNODES with NUMA_NO_NODE in
memblock_set_node() and use NUMA_NO_NODE in x86::numa_init()"
* tag 'fixes-2024-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
x86/mm/numa: Use NUMA_NO_NODE when calling memblock_set_node()
memblock: make memblock_set_node() also warn about use of MAX_NUMNODES
|
|
This is a re-commit of
da05b143a308 ("x86/boot: Don't add the EFI stub to targets")
after the tagged patch incorrectly reverted it.
vmlinux-objs-y is added to targets, with an assumption that they are all
relative to $(obj); adding a $(objtree)/drivers/... path causes the
build to incorrectly create a useless
arch/x86/boot/compressed/drivers/... directory tree.
Fix this just by using a different make variable for the EFI stub.
Fixes: cb8bda8ad443 ("x86/boot/compressed: Rename efi_thunk_64.S to efi-mixed.S")
Signed-off-by: Ben Segall <bsegall@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Cc: stable@vger.kernel.org # v6.1+
Link: https://lore.kernel.org/r/xm267ceukksz.fsf@bsegall.svl.corp.google.com
|
|
This reverts commit 277a0363120276645ae598d8d5fea7265e076ae9.
While fixing old boards with broken DTs, this change will break
newer ones with correct gpio polarity annotation.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Pull ARM and clkdev fixes from Russell King:
- Fix clkdev - erroring out on long strings causes boot failures, so
don't do this. Still warn about the over-sized strings (which will
never match and thus their registration with clkdev is useless)
- Fix for ftrace with frame pointer unwinder with recent GCC changing
the way frames are stacked.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rmk/linux:
ARM: 9405/1: ftrace: Don't assume stack frames are contiguous in memory
clkdev: don't fail clkdev_alloc() if over-sized
|
|
PA-RISC systems with PA8800 and PA8900 processors have had problems
with random segmentation faults for many years. Systems with earlier
processors are much more stable.
Systems with PA8800 and PA8900 processors have a large L2 cache which
needs per page flushing for decent performance when a large range is
flushed. The combined cache in these systems is also more sensitive to
non-equivalent aliases than the caches in earlier systems.
The majority of random segmentation faults that I have looked at
appear to be memory corruption in memory allocated using mmap and
malloc.
My first attempt at fixing the random faults didn't work. On
reviewing the cache code, I realized that there were two issues
which the existing code didn't handle correctly. Both relate
to cache move-in. Another issue is that the present bit in PTEs
is racy.
1) PA-RISC caches have a mind of their own and they can speculatively
load data and instructions for a page as long as there is a entry in
the TLB for the page which allows move-in. TLBs are local to each
CPU. Thus, the TLB entry for a page must be purged before flushing
the page. This is particularly important on SMP systems.
In some of the flush routines, the flush routine would be called
and then the TLB entry would be purged. This was because the flush
routine needed the TLB entry to do the flush.
2) My initial approach to trying the fix the random faults was to
try and use flush_cache_page_if_present for all flush operations.
This actually made things worse and led to a couple of hardware
lockups. It finally dawned on me that some lines weren't being
flushed because the pte check code was racy. This resulted in
random inequivalent mappings to physical pages.
The __flush_cache_page tmpalias flush sets up its own TLB entry
and it doesn't need the existing TLB entry. As long as we can find
the pte pointer for the vm page, we can get the pfn and physical
address of the page. We can also purge the TLB entry for the page
before doing the flush. Further, __flush_cache_page uses a special
TLB entry that inhibits cache move-in.
When switching page mappings, we need to ensure that lines are
removed from the cache. It is not sufficient to just flush the
lines to memory as they may come back.
This made it clear that we needed to implement all the required
flush operations using tmpalias routines. This includes flushes
for user and kernel pages.
After modifying the code to use tmpalias flushes, it became clear
that the random segmentation faults were not fully resolved. The
frequency of faults was worse on systems with a 64 MB L2 (PA8900)
and systems with more CPUs (rp4440).
The warning that I added to flush_cache_page_if_present to detect
pages that couldn't be flushed triggered frequently on some systems.
Helge and I looked at the pages that couldn't be flushed and found
that the PTE was either cleared or for a swap page. Ignoring pages
that were swapped out seemed okay but pages with cleared PTEs seemed
problematic.
I looked at routines related to pte_clear and noticed ptep_clear_flush.
The default implementation just flushes the TLB entry. However, it was
obvious that on parisc we need to flush the cache page as well. If
we don't flush the cache page, stale lines will be left in the cache
and cause random corruption. Once a PTE is cleared, there is no way
to find the physical address associated with the PTE and flush the
associated page at a later time.
I implemented an updated change with a parisc specific version of
ptep_clear_flush. It fixed the random data corruption on Helge's rp4440
and rp3440, as well as on my c8000.
At this point, I realized that I could restore the code where we only
flush in flush_cache_page_if_present if the page has been accessed.
However, for this, we also need to flush the cache when the accessed
bit is cleared in ptep_clear_flush_young to keep things synchronized.
The default implementation only flushes the TLB entry.
Other changes in this version are:
1) Implement parisc specific version of ptep_get. It's identical to
default but needed in arch/parisc/include/asm/pgtable.h.
2) Revise parisc implementation of ptep_test_and_clear_young to use
ptep_get (READ_ONCE).
3) Drop parisc implementation of ptep_get_and_clear. We can use default.
4) Revise flush_kernel_vmap_range and invalidate_kernel_vmap_range to
use full data cache flush.
5) Move flush_cache_vmap and flush_cache_vunmap to cache.c. Handle
VM_IOREMAP case in flush_cache_vmap.
At this time, I don't know whether it is better to always flush when
the PTE present bit is set or when both the accessed and present bits
are set. The later saves flushing pages that haven't been accessed,
but we need to flush in ptep_clear_flush_young. It also needs a page
table lookup to find the PTE pointer. The lpa instruction only needs
a page table lookup when the PTE entry isn't in the TLB.
We don't atomically handle setting and clearing the _PAGE_ACCESSED bit.
If we miss an update, we may miss a flush and the cache may get corrupted.
Whether the current code is effectively atomic depends on process control.
When CONFIG_FLUSH_PAGE_ACCESSED is set to zero, the page will eventually
be flushed when the PTE is cleared or in flush_cache_page_if_present. The
_PAGE_ACCESSED bit is not used, so the problem is avoided.
The flush method can be selected using the CONFIG_FLUSH_PAGE_ACCESSED
define in cache.c. The default is 0. I didn't see a large difference
in performance.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # v6.6+
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
When reworking the range checking for get_user(), the get_user_8() case
on 32-bit wasn't zeroing the high register. (The jump to bad_get_user_8
was accidentally dropped.) Restore the correct error handling
destination (and rename the jump to using the expected ".L" prefix).
While here, switch to using a named argument ("size") for the call
template ("%c4" to "%c[size]") as already used in the other call
templates in this file.
Found after moving the usercopy selftests to KUnit:
# usercopy_test_invalid: EXPECTATION FAILED at
lib/usercopy_kunit.c:278
Expected val_u64 == 0, but
val_u64 == -60129542144 (0xfffffff200000000)
Closes: https://lore.kernel.org/all/CABVgOSn=tb=Lj9SxHuT4_9MTjjKVxsq-ikdXC4kGHO4CfKVmGQ@mail.gmail.com
Fixes: b19b74bc99b1 ("x86/mm: Rework address range check in get_user() and put_user()")
Reported-by: David Gow <davidgow@google.com>
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Tested-by: David Gow <davidgow@google.com>
Link: https://lore.kernel.org/all/20240610210213.work.143-kees%40kernel.org
|
|
According to the FF-A spec (Buffer states and ownership), after a
producer has written into a buffer, it is "full" and now owned by the
consumer. The producer won't be able to use that buffer, until the
consumer hands it over with an invocation such as RX_RELEASE.
It is clear in the following paragraph (Transfer of buffer ownership),
that MEM_RETRIEVE_RESP is transferring the ownership from producer (in
our case SPM) to consumer (hypervisor). RX_RELEASE is therefore
mandatory here.
It is less clear though what is happening with MEM_FRAG_TX. But this
invocation, as a response to MEM_FRAG_RX writes into the same hypervisor
RX buffer (see paragraph "Transmission of transaction descriptor in
fragments"). Also this is matching the TF-A implementation where the RX
buffer is marked "full" during a MEM_FRAG_RX.
Release the RX hypervisor buffer in those two cases. This will unblock
later invocations using this buffer which would otherwise fail.
(RETRIEVE_REQ, MEM_FRAG_RX and PARTITION_INFO_GET).
Signed-off-by: Vincent Donnefort <vdonnefort@google.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20240611175317.1220842-1-vdonnefort@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
Since physical and virtual kernel address spaces are uncoupled
the kernel image is not mapped using large segment pages anymore,
which is a regression.
Put the kernel image at the same large segment page offset in
physical memory as in virtual memory. Such approach preserves
the existing number of bits of entropy used for randomization
of the kernel location in virtual memory when KASLR is on.
As result, the kernel is mapped using large segment pages.
Fixes: c98d2ecae08f ("s390/mm: Uncouple physical vs virtual address spaces")
Reported-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Do not allow creation of large pages against physical addresses,
which itself are not aligned on the correct boundary. Failure to
do so might lead to referencing wrong memory as result of the way
DAT works.
Fixes: c98d2ecae08f ("s390/mm: Uncouple physical vs virtual address spaces")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
It was discovered that some device have CBR address set to 0 causing
kernel panic when arch_sync_dma_for_cpu_all is called.
This was notice in situation where the system is booted from TP1 and
BMIPS_GET_CBR() returns 0 instead of a valid address and
!!(read_c0_brcm_cmt_local() & (1 << 31)); not failing.
The current check whether RAC flush should be disabled or not are not
enough hence lets check if CBR is a valid address or not.
Fixes: ab327f8acdf8 ("mips: bmips: BCM6358: disable RAC flush for TP1")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Commit 90c2d2eb7ab5 ("MIPS: pci: lantiq: switch to using gpiod API") not
only switched to the gpiod API, but also inverted / changed the polarity
of the GPIO.
According to the PCI specification, the RST# pin is an active-low
signal. However, most of the device trees that have been widely used for
a long time (mainly in the openWrt project) define this GPIO as
active-high and the old driver code inverted the signal internally.
Apparently there are actually boards where the reset gpio must be
operated inverted. For this reason, we cannot use the GPIOD_OUT_LOW/HIGH
flag for initialization. Instead, we must explicitly set the gpio to
value 1 in order to take into account any "GPIO_ACTIVE_LOW" flag that
may have been set.
In order to remain compatible with all these existing device trees, we
should therefore keep the logic as it was before the commit.
Fixes: 90c2d2eb7ab5 ("MIPS: pci: lantiq: switch to using gpiod API")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
read_config_dword() contains strange condition checking ret for a
number of values. The ret variable, however, is always zero because
config_access() never returns anything else. Thus, the retry is always
taken until number of tries is exceeded.
The code looks like it wants to check *val instead of ret to see if the
read gave an error response.
Fixes: 73b4390fb234 ("[MIPS] Routerboard 532: Support for base system")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The frame pointer unwinder relies on a standard layout of the stack
frame, consisting of (in downward order)
Calling frame:
PC <---------+
LR |
SP |
FP |
.. locals .. |
Callee frame: |
PC |
LR |
SP |
FP ----------+
where after storing its previous value on the stack, FP is made to point
at the location of PC in the callee stack frame, using the canonical
prologue:
mov ip, sp
stmdb sp!, {fp, ip, lr, pc}
sub fp, ip, #4
The ftrace code assumes that this activation record is pushed first, and
that any stack space for locals is allocated below this. Strict
adherence to this would imply that the caller's value of SP at the time
of the function call can always be obtained by adding 4 to FP (which
points to PC in the callee frame).
However, recent versions of GCC appear to deviate from this rule, and so
the only reliable way to obtain the caller's value of SP is to read it
from the activation record. Since this involves a read from memory
rather than simple arithmetic, we need to use the uaccess API here which
protects against inadvertent data aborts resulting from attempts to
dereference bogus FP values.
The plain uaccess API is ftrace instrumented itself, so to avoid
unbounded recursion, use the __get_kernel_nofault() primitive directly.
Closes: https://lore.kernel.org/all/alp44tukzo6mvcwl4ke4ehhmojrqnv6xfcdeuliybxfjfvgd3e@gpjvwj33cc76
Closes: https://lore.kernel.org/all/d870c149-4363-43de-b0ea-7125dec5608e@broadcom.com/
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Justin Chen <justin.chen@broadcom.com>
Tested-by: Thorsten Scherer <t.scherer@eckelmann.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Miscellaneous fixes:
- Fix kexec() crash if call depth tracking is enabled
- Fix SMN reads on inaccessible registers on certain AMD systems"
* tag 'x86-urgent-2024-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/amd_nb: Check for invalid SMN reads
x86/kexec: Fix bug with call depth tracking
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"14 hotfixes, 6 of which are cc:stable.
All except the nilfs2 fix affect MM and all are singletons - see the
chagelogs for details"
* tag 'mm-hotfixes-stable-2024-06-07-15-24' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
nilfs2: fix nilfs_empty_dir() misjudgment and long loop on I/O errors
mm: fix xyz_noprof functions calling profiled functions
codetag: avoid race at alloc_slab_obj_exts
mm/hugetlb: do not call vma_add_reservation upon ENOMEM
mm/ksm: fix ksm_zero_pages accounting
mm/ksm: fix ksm_pages_scanned accounting
kmsan: do not wipe out origin when doing partial unpoisoning
vmalloc: check CONFIG_EXECMEM in is_vmalloc_or_module_addr()
mm: page_alloc: fix highatomic typing in multi-block buddies
nilfs2: fix potential kernel bug due to lack of writeback flag waiting
memcg: remove the lockdep assert from __mod_objcg_mlstate()
mm: arm64: fix the out-of-bounds issue in contpte_clear_young_dirty_ptes
mm: huge_mm: fix undefined reference to `mthp_stats' for CONFIG_SYSFS=n
mm: drop the 'anon_' prefix for swap-out mTHP counters
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- Another fix to avoid allocating pages that overlap with ERR_PTR,
which manifests on rv32
- A revert for the badaccess patch I incorrectly picked up an early
version of
* tag 'riscv-for-linus-6.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
Revert "riscv: mm: accelerate pagefault when badaccess"
riscv: fix overlap of allocated page and PTR_ERR
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Alexander Gordeev:
- Do not create PT_LOAD program header for the kenel image when the
virtual memory informaton in OS_INFO data is not available. That
fixes stand-alone dump failures against kernels that do not provide
the virtual memory informaton
- Add KVM s390 shared zeropage selftest
* tag 's390-6.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
KVM: s390x: selftests: Add shared zeropage test
s390/crash: Do not use VM info if os_info does not have it
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- Fix spurious CPU hotplug warning message from SETEND emulation code
- Fix the build when GCC wasn't inlining our I/O accessor internals
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/io: add constant-argument check
arm64: armv8_deprecated: Fix warning in isndep cpuhp starting process
|
|
memblock_set_node() warns about using MAX_NUMNODES, see
e0eec24e2e19 ("memblock: make memblock_set_node() also warn about use of MAX_NUMNODES")
for details.
Reported-by: Narasimhan V <Narasimhan.V@amd.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
[bp: commit message]
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Mike Rapoport (IBM) <rppt@kernel.org>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20240603141005.23261-1-bp@kernel.org
Link: https://lore.kernel.org/r/abadb736-a239-49e4-ab42-ace7acdd4278@suse.com
Signed-off-by: Mike Rapoport (IBM) <rppt@kernel.org>
|
|
When tearing down a redistributor region, make sure we don't have
any dangling pointer to that region stored in a vcpu.
Fixes: e5a35635464b ("kvm: arm64: vgic-v3: Introduce vgic_v3_free_redist_region()")
Reported-by: Alexander Potapenko <glider@google.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240605175637.1635653-1-maz@kernel.org
Cc: stable@vger.kernel.org
|
|
We are passing a huge nr to __clear_young_dirty_ptes() right now. While
we should pass the number of pages, we are actually passing CONT_PTE_SIZE.
This is causing lots of crashes of MADV_FREE, panic oops could vary
everytime.
Link: https://lkml.kernel.org/r/20240524005444.135417-1-21cnbao@gmail.com
Fixes: 89e86854fb0a ("mm/arm64: override clear_young_dirty_ptes() batch helper")
Signed-off-by: Barry Song <v-songbaohua@oppo.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Acked-by: Lance Yang <ioworker0@gmail.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Chris Li <chrisl@kernel.org>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Jeff Xie <xiehuan09@gmail.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Yin Fengwei <fengwei.yin@intel.com>
Cc: Zach O'Keefe <zokeefe@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
AMD Zen-based systems use a System Management Network (SMN) that
provides access to implementation-specific registers.
SMN accesses are done indirectly through an index/data pair in PCI
config space. The PCI config access may fail and return an error code.
This would prevent the "read" value from being updated.
However, the PCI config access may succeed, but the return value may be
invalid. This is in similar fashion to PCI bad reads, i.e. return all
bits set.
Most systems will return 0 for SMN addresses that are not accessible.
This is in line with AMD convention that unavailable registers are
Read-as-Zero/Writes-Ignored.
However, some systems will return a "PCI Error Response" instead. This
value, along with an error code of 0 from the PCI config access, will
confuse callers of the amd_smn_read() function.
Check for this condition, clear the return value, and set a proper error
code.
Fixes: ddfe43cdc0da ("x86/amd_nb: Add SMN and Indirect Data Fabric access for AMD Fam17h")
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230403164244.471141-1-yazen.ghannam@amd.com
|
|
Pull kvm fixes from Paolo Bonzini:
"This is dominated by a couple large series for ARM and x86
respectively, but apart from that things are calm.
ARM:
- Large set of FP/SVE fixes for pKVM, addressing the fallout from the
per-CPU data rework and making sure that the host is not involved
in the FP/SVE switching any more
- Allow FEAT_BTI to be enabled with NV now that FEAT_PAUTH is
completely supported
- Fix for the respective priorities of Failed PAC, Illegal Execution
state and Instruction Abort exceptions
- Fix the handling of AArch32 instruction traps failing their
condition code, which was broken by the introduction of
ESR_EL2.ISS2
- Allow vcpus running in AArch32 state to be restored in System mode
- Fix AArch32 GPR restore that would lose the 64 bit state under some
conditions
RISC-V:
- No need to use mask when hart-index-bits is 0
- Fix incorrect reg_subtype labels in
kvm_riscv_vcpu_set_reg_isa_ext()
x86:
- Fixes and debugging help for the #VE sanity check.
Also disable it by default, even for CONFIG_DEBUG_KERNEL, because
it was found to trigger spuriously (most likely a processor erratum
as the exact symptoms vary by generation).
- Avoid WARN() when two NMIs arrive simultaneously during an
NMI-disabled situation (GIF=0 or interrupt shadow) when the
processor supports virtual NMI.
While generally KVM will not request an NMI window when virtual
NMIs are supported, in this case it *does* have to single-step over
the interrupt shadow or enable the STGI intercept, in order to
deliver the latched second NMI.
- Drop support for hand tuning APIC timer advancement from userspace.
Since we have adaptive tuning, and it has proved to work well, drop
the module parameter for manual configuration and with it a few
stupid bugs that it had"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (32 commits)
KVM: x86/mmu: Don't save mmu_invalidate_seq after checking private attr
KVM: arm64: Ensure that SME controls are disabled in protected mode
KVM: arm64: Refactor CPACR trap bit setting/clearing to use ELx format
KVM: arm64: Consolidate initializing the host data's fpsimd_state/sve in pKVM
KVM: arm64: Eagerly restore host fpsimd/sve state in pKVM
KVM: arm64: Allocate memory mapped at hyp for host sve state in pKVM
KVM: arm64: Specialize handling of host fpsimd state on trap
KVM: arm64: Abstract set/clear of CPTR_EL2 bits behind helper
KVM: arm64: Fix prototype for __sve_save_state/__sve_restore_state
KVM: arm64: Reintroduce __sve_save_state
KVM: x86: Drop support for hand tuning APIC timer advancement from userspace
KVM: SEV-ES: Delegate LBR virtualization to the processor
KVM: SEV-ES: Disallow SEV-ES guests when X86_FEATURE_LBRV is absent
KVM: SEV-ES: Prevent MSR access post VMSA encryption
RISC-V: KVM: Fix incorrect reg_subtype labels in kvm_riscv_vcpu_set_reg_isa_ext function
RISC-V: KVM: No need to use mask when hart-index-bit is 0
KVM: arm64: nv: Expose BTI and CSV_frac to a guest hypervisor
KVM: arm64: nv: Fix relative priorities of exceptions generated by ERETAx
KVM: arm64: AArch32: Fix spurious trapping of conditional instructions
KVM: arm64: Allow AArch32 PSTATE.M to be restored as System mode
...
|
|
The virtual memory information stored in os_info area is
required for creation of the kernel image PT_LOAD program
header for kernels since commit a2ec5bec56dd ("s390/mm:
uncouple physical vs virtual address spaces").
By contrast, if such information in os_info is absent the
PT_LOAD program header should not be created.
Currently the proper PT_LOAD program header is created for
kernels that contain the virtual memory information, but
for kernels without one an invalid header of zero size is
created. That in turn leads to stand-alone dump failures.
Use OS_INFO_KASLR_OFFSET variable to check whether os_info
is present or not (same as crash and makedumpfile tools do)
and based on that create or do not create the kernel image
PT_LOAD program header.
Fixes: f4cac27dc0d6 ("s390/crash: Use old os_info to create PT_LOAD headers")
Tested-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Acked-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
In some configurations __const_iowrite32_copy() does not get inlined
and gcc runs into the BUILD_BUG():
In file included from <command-line>:
In function '__const_memcpy_toio_aligned32',
inlined from '__const_iowrite32_copy' at arch/arm64/include/asm/io.h:203:3,
inlined from '__const_iowrite32_copy' at arch/arm64/include/asm/io.h:199:20:
include/linux/compiler_types.h:487:45: error: call to '__compiletime_assert_538' declared with attribute error: BUILD_BUG failed
487 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
| ^
include/linux/compiler_types.h:468:25: note: in definition of macro '__compiletime_assert'
468 | prefix ## suffix(); \
| ^~~~~~
include/linux/compiler_types.h:487:9: note: in expansion of macro '_compiletime_assert'
487 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
| ^~~~~~~~~~~~~~~~~~~
include/linux/build_bug.h:39:37: note: in expansion of macro 'compiletime_assert'
39 | #define BUILD_BUG_ON_MSG(cond, msg) compiletime_assert(!(cond), msg)
| ^~~~~~~~~~~~~~~~~~
include/linux/build_bug.h:59:21: note: in expansion of macro 'BUILD_BUG_ON_MSG'
59 | #define BUILD_BUG() BUILD_BUG_ON_MSG(1, "BUILD_BUG failed")
| ^~~~~~~~~~~~~~~~
arch/arm64/include/asm/io.h:193:17: note: in expansion of macro 'BUILD_BUG'
193 | BUILD_BUG();
| ^~~~~~~~~
Move the check for constant arguments into the inline function to ensure
it is still constant if the compiler decides against inlining it, and
mark them as __always_inline to override the logic that sometimes leads
to the compiler not producing the simplified output.
Note that either the __always_inline annotation or the check for a
constant value are sufficient here, but combining the two looks cleaner
as it also avoids the macro. With clang-8 and older, the macro was still
needed, but all versions of gcc and clang can reliably perform constant
folding here.
Fixes: ead79118dae6 ("arm64/io: Provide a WC friendly __iowriteXX_copy()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20240604210006.668912-1-arnd@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|