Age | Commit message (Collapse) | Author | Files | Lines |
|
This is way to catch some cases of decrementer overflow, when the
decrementer has underflowed an odd number of times, while MSR[EE] was
disabled.
With a typical small decrementer, a timer that fires when MSR[EE] is
disabled will be "lost" if MSR[EE] remains disabled for between 4.3 and
8.6 seconds after the timer expires. In any case, the decrementer
interrupt would be taken at 8.6 seconds and the timer would be found at
that point.
So this check is for catching extreme latency events, and it prevents
those latencies from being a further few seconds long. It's not obvious
this is a good tradeoff. This is already a watchdog magnitude event and
that situation is not improved a significantly with this check. For
large decrementers, it's useless.
Therefore remove this check, which avoids a mftb when enabling hard
disabled interrupts (e.g., when enabling after coming from hardware
interrupt handlers). Perhaps more importantly, it also removes the
clunky MSR[EE] vs PACA_IRQ_HARD_DIS incoherency in soft-interrupt replay
which simplifies the code.
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
No supported processor implements this mode. Setting the bit in
MSR values can be a bit confusing (and would prevent the bit from
ever being reused). Remove it.
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
PTE_FLAGS_OFFSET is defined in asm/page_32.h and used only
in hash_low.S
And PTE_FLAGS_OFFSET nullity depends on CONFIG_PTE_64BIT
Instead of tests like #if (PTE_FLAGS_OFFSET != 0), use
CONFIG_PTE_64BIT related code.
Also move the definition of PTE_FLAGS_OFFSET into hash_low.S
directly, that improves readability.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/f5bc21db7a33dab55924734e6060c2e9daed562e.1606247495.git.christophe.leroy@csgroup.eu
|
|
VSID is only for create_hpte(). When _PAGE_HASHPTE is
already set, add_hash_page() bails out without calling
create_hpte() and doesn't need the value of VSID.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/3907199974c89b85a3441cf3f528751173b7649c.1606247495.git.christophe.leroy@csgroup.eu
|
|
primary_pteg_full and htab_hash_searches are not used.
Remove them.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/6470ab99e58c84a5445af43ce4d1d772b0dc3e93.1606247495.git.christophe.leroy@csgroup.eu
|
|
All hugetlb range freeing functions have a verification like the following,
which only differs by the mask used, depending on the page table level.
start &= MASK;
if (start < floor)
return;
if (ceiling) {
ceiling &= MASK;
if (! ceiling)
return;
}
if (end - 1 > ceiling - 1)
return;
Refactor that into a helper function which takes the mask as
an argument, returning true when [start;end[ is not fully
contained inside [floor;ceiling[
Signed-off-by: Christophe Leroy <[email protected]>
Reviewed-by: Aneesh Kumar K.V <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/16a571bb32eb6e8cd44bda484c8d81cd8a25e6d7.1604668827.git.christophe.leroy@csgroup.eu
|
|
Exception fixup doesn't require the heady full regs saving,
do it from do_page_fault() directly.
For that, split bad_page_fault() in two parts.
As bad_page_fault() can also be called from other places than
handle_page_fault(), it will still perform exception fixup and
fallback on __bad_page_fault().
handle_page_fault() directly calls __bad_page_fault() as the
exception fixup will now be done by do_page_fault()
Signed-off-by: Christophe Leroy <[email protected]>
Reviewed-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/bd07d6fef9237614cd6d318d8f19faeeadaa816b.1607491748.git.christophe.leroy@csgroup.eu
|
|
search_exception_tables() is an heavy operation, we have to avoid it.
When KUAP is selected, we'll know the fault has been blocked by KUAP.
When it is blocked by KUAP, check whether we are in an expected
userspace access place. If so, emit a warning to spot something is
going work. Otherwise, just remain silent, it will likely Oops soon.
When KUAP is not selected, it behaves just as if the address was
already in the TLBs and no fault was generated.
Signed-off-by: Christophe Leroy <[email protected]>
Reviewed-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/9870f01e293a5a76c4f4e4ddd4a6b0f63038c591.1607491748.git.christophe.leroy@csgroup.eu
|
|
In order to prepare the removal of calls to
search_exception_tables() on the fast path, move the
WARN() out of bad_kuap_fault().
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/9501311014bd6507e04b27a0c3035186ccf65cd5.1607491748.git.christophe.leroy@csgroup.eu
|
|
page_fault_is_bad()
To make it more readable, separate page_fault_is_write() and page_fault_is_bad()
to avoir several levels of #ifdefs
Signed-off-by: Christophe Leroy <[email protected]>
Reviewed-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/6afaac2495248d68f94c438c5ec36b6010931de5.1607491748.git.christophe.leroy@csgroup.eu
|
|
The verification and message introduced by commit 374f3f5979f9
("powerpc/mm/hash: Handle user access of kernel address gracefully")
applies to all platforms, it should not be limited to BOOK3S.
Make the BOOK3S version of sanity_check_fault() the one for all,
and bail out earlier if not BOOK3S.
Fixes: 374f3f5979f9 ("powerpc/mm/hash: Handle user access of kernel address gracefully")
Signed-off-by: Christophe Leroy <[email protected]>
Reviewed-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/fe199d5af3578d3bf80035d203a94d742a7a28af.1607491748.git.christophe.leroy@csgroup.eu
|
|
Add PPC_RAW_MFSPR() to replace open coding done in 8xx-pmu.c
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/e281e3a611eead8817c49cf06a60072a021af823.1606231483.git.christophe.leroy@csgroup.eu
|
|
Use SPRN_SPRG_SCRATCH2 in DTLB miss exception instead of DAR
in order to be similar to ITLB miss exception.
This also simplifies mpc8xx_pmu_del()
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/e3cc8f023ef40e1e8ae144e4dd1330a5ff022528.1606231483.git.christophe.leroy@csgroup.eu
|
|
In order to re-enable MMU earlier, ensure ITLB miss exception
cannot clobber SPRN_SPRG_SCRATCH0 and SPRN_SPRG_SCRATCH1.
Do so by using SPRN_SPRG_SCRATCH2 and SPRN_M_TW instead, like
the DTLB miss exception.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/abc78e8e9577d473691ebb9996c6413b37bfd9ca.1606231483.git.christophe.leroy@csgroup.eu
|
|
We now have r11 available as a scratch register so
INVALIDATE_ADJACENT_PAGES_CPU15() can be simplified.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/bdafd651b4ac3a851fd09249f5f3699c50da29f2.1606231483.git.christophe.leroy@csgroup.eu
|
|
There is no big poing in not pinning kernel text anymore, as now
we can keep pinned TLB even with things like DEBUG_PAGEALLOC.
Remove CONFIG_PIN_TLB_TEXT, making it always right.
Signed-off-by: Christophe Leroy <[email protected]>
[mpe: Drop ifdef around mmu_pin_tlb() to fix build errors]
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/203b89de491e1379f1677a2685211b7c32adfff0.1606231483.git.christophe.leroy@csgroup.eu
|
|
kvmarm-master/next
Signed-off-by: Marc Zyngier <[email protected]>
|
|
sync_core_before_usermode() had an incorrect optimization. If the kernel
returns from an interrupt, it can get to usermode without IRET. It just has
to schedule to a different task in the same mm and do SYSRET. Fortunately,
there were no callers of sync_core_before_usermode() that could have had
in_irq() or in_nmi() equal to true, because it's only ever called from the
scheduler.
While at it, clarify a related comment.
Fixes: 70216e18e519 ("membarrier: Provide core serializing command, *_SYNC_CORE")
Signed-off-by: Andy Lutomirski <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Mathieu Desnoyers <[email protected]>
Cc: [email protected]
Link: https://lore.kernel.org/r/5afc7632be1422f91eaf7611aaaa1b5b8580a086.1607058304.git.luto@kernel.org
|
|
Now that ARM started following the example of arm64 and RISC-V, and
no longer imposes any restrictions on the placement of the FDT in
memory at boot, we no longer need per-arch implementations of
efi_get_max_fdt_addr() to factor out the differences. So get rid of
it.
Signed-off-by: Ard Biesheuvel <[email protected]>
Reviewed-by: Atish Patra <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Now that we reduced the minimum relative alignment between PHYS_OFFSET
and PAGE_OFFSET to 2 MiB, we can take this into account when allocating
memory for the decompressed kernel when booting via EFI. This minimizes
the amount of unusable memory we may end up with due to the base of DRAM
being occupied by firmware.
Signed-off-by: Ard Biesheuvel <[email protected]>
|
|
Scatter-gather lists passed to UpdateCapsule() should be cleaned
from the D-cache to ensure that they are visible to the CPU after a
warm reboot before the MMU is enabled. On ARM and arm64 systems, this
implies a D-cache clean by virtual address to the point of coherency.
However, due to the fact that the firmware itself is not able to map
physical addresses back to virtual addresses when running under the OS,
this must be done by the caller.
Signed-off-by: Ard Biesheuvel <[email protected]>
|
|
Since commit e611939fc8ec ("powerpc/mm: Ensure change_page_attr()
doesn't invalidate pinned TLBs"), pinned TLBs are not anymore
invalidated by __kernel_map_pages() when CONFIG_DEBUG_PAGEALLOC is
selected.
Remove the dependency on CONFIG_DEBUG_PAGEALLOC.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/e796c5fcb5898de827c803cf1ab8ba1d7a5d4b76.1606231483.git.christophe.leroy@csgroup.eu
|
|
__set_dabr() are simple functions that can be inline directly
inside set_dabr() and using IS_ENABLED() instead of #ifdef
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/c10b263668e137236c71d76648b03cf2cd1ee66f.1607076733.git.christophe.leroy@csgroup.eu
|
|
When SMC1 is relocated and early debug is selected, the
board hangs is ppc_md.setup_arch(). This is because ones
the microcode has been loaded and SMC1 relocated, early
debug writes in the weed.
To allow smooth continuation, the SMC1 parameter RAM set up
by the bootloader have to be copied into the new location.
Fixes: 43db76f41824 ("powerpc/8xx: Add microcode patch to move SMC parameter RAM.")
Cc: [email protected]
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/b2f71f39eca543f1e4ec06596f09a8b12235c701.1607076683.git.christophe.leroy@csgroup.eu
|
|
On hash 32 bits, handling minor protection faults like unsetting
dirty flag is heavy if done from the normal page_fault processing,
because it implies hash table software lookup for flushing the entry
and then a DSI is taken anyway to add the entry back.
When KUAP was implemented, as explained in commit a68c31fc01ef
("powerpc/32s: Implement Kernel Userspace Access Protection"),
protection faults has been diverted from hash_page() because
hash_page() was not able to identify a KUAP fault.
Implement KUAP verification in hash_page(), by clearing write
permission when the access is a kernel access and Ks is 1.
This works regardless of the address because kernel segments always
have Ks set to 0 while user segments have Ks set to 0 only
when kernel write to userspace is granted.
Then protection faults can be handled by hash_page() even for KUAP.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/8a4ffe4798e9ea32aaaccdf85e411bb1beed3500.1605542955.git.christophe.leroy@csgroup.eu
|
|
book3s/32 has two main families:
- CPU with 603 cores that don't have HASH PTE table and
perform SW TLB loading.
- Other CPUs based on 604+ cores that have HASH PTE table.
This leads to some complex logic and additionnal code to
support both. This makes sense for distribution kernels
that aim at running on any CPU, but when you are fine
tuning a kernel for an embedded 603 based board you
don't need all the HASH logic.
Allow selection of support for each family, in order to opt
out unneeded parts of code. At least one must be selected.
Note that some of the CPU supporting HASH also support SW TLB
loading, however it is not supported by Linux kernel at the
time being, because they do not have alternate registers in
the TLB miss exception handlers.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/8dde0cdb629a71abc29b0d85a52a86e920376cb6.1603348103.git.christophe.leroy@csgroup.eu
|
|
In order to selectively build the kernel for 603 SW TLB handling,
regroup all 603 based CPUs together.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/45065263fdb9f5cc2a2d210ec2a762ac8bf5b2bc.1603348103.git.christophe.leroy@csgroup.eu
|
|
As 601 is gone, CONFIG_PPC_BOO3S_6xx and CONFIG_PPC_BOOK3S_32
are dedundant.
Remove CONFIG_PPC_BOOK3S_6xx.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/f18c16af37f6f77b577bed8d9e12831b695617ae.1603348103.git.christophe.leroy@csgroup.eu
|
|
early_mmu_init() is independent of MMU type and not
directly linked to tlb handling.
In a following patch, tlb.c will be restricted to HASH mmu.
Move early_mmu_init() into mmu.c which is common.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/e51b5e2fe6bca623b33116403043d3a1b5eaf826.1603348103.git.christophe.leroy@csgroup.eu
|
|
flush_hash_entry() is a simple function calling
flush_hash_pages() if it's a hash MMU or doing nothing otherwise.
Inline it.
And use it also in __ptep_test_and_clear_young().
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/9af895be7d4b404d40e749a2659552fd138e62c4.1603348103.git.christophe.leroy@csgroup.eu
|
|
On book3s/32, tlb_flush() does nothing when the CPU has a hash table,
it calls _tlbia() otherwise.
Inline it.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/ebc933d1c530a19ef3cf7983f6ae94814f6e92ac.1603348103.git.christophe.leroy@csgroup.eu
|
|
flush_range() handle both the MMU_FTR_HPTE_TABLE case and
the other case.
The non MMU_FTR_HPTE_TABLE case is trivial as it is only a call
to _tlbie()/_tlbia() which is not worth a dedicated function.
Make flush_range() a hash specific and call it from tlbflush.h based
on mmu_has_feature(MMU_FTR_HPTE_TABLE).
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/132ab19aae52abc8e06ab524ec86d4229b5b9c3d.1603348103.git.christophe.leroy@csgroup.eu
|
|
flush_tlb_range() and flush_tlb_kernel_range() are trivial calls to
flush_range().
Make flush_range() global and inline flush_tlb_range()
and flush_tlb_kernel_range().
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/c7029a78e78709ad9272d7a44260e06b649169b2.1603348103.git.christophe.leroy@csgroup.eu
|
|
flush_tlb_mm() and flush_tlb_page() handle both the MMU_FTR_HPTE_TABLE
case and the other case.
The non MMU_FTR_HPTE_TABLE case is trivial as it is only a call
to _tlbie()/_tlbia() which is not worth a dedicated function.
Make flush_tlb_mm() and flush_tlb_page() hash specific and call
them from tlbflush.h based on mmu_has_feature(MMU_FTR_HPTE_TABLE).
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/11e932ded41ba6d9b251d89b7afa33cc060d3aa4.1603348103.git.christophe.leroy@csgroup.eu
|
|
_tlbie() and _tlbia() are used only on 603 cores while the
other functions are used only on cores having a hash table.
Move them into a new file named nohash_low.S
Add mmu_hash_lock var is used by both, it needs to go
in a common file.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/9a265b1b17a64153463d361280cb4b43eb1266a4.1603348103.git.christophe.leroy@csgroup.eu
|
|
On non SMP, _tlbie() is just a tlbie plus a sync instruction.
Make it static inline.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/475136425541db5c7c8a0395d19d400525b251bc.1603348103.git.christophe.leroy@csgroup.eu
|
|
In order to use _tlbie() and _tlbia() directly
from asm/book3s/32/tlbflush.h, move their prototypes
from mm/mm_decl.h to there.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/867587af929973ad65f8ef6972f2474a80c1737a.1603348103.git.christophe.leroy@csgroup.eu
|
|
Hash related vars are used at init only.
Declare them in __initdata.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/3878ea30706839fcff9196790ff3f99c128c3f6a.1603348103.git.christophe.leroy@csgroup.eu
|
|
Hash var is used only locally in mmu.c now.
No need to set it in head_32.S anymore.
Make it static and initialises it to the early hash table.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/786c82a89cdfdaabb32b72a44f7c312fa81d192b.1603348103.git.christophe.leroy@csgroup.eu
|
|
Hash var
We now have an early hash table on hash MMU, so no need to check
Hash var to know if the Hash table is set of not.
Use mmu_has_feature(MMU_FTR_HPTE_TABLE) instead. This will allow
optimisation via jump_label.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/f1766631a9e014b6433f1a3c12c726ddfce34220.1603348103.git.christophe.leroy@csgroup.eu
|
|
This table is used only locally. Declare it static.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/054fec0c139fc4c0a306360b360784733c0a6e65.1603348103.git.christophe.leroy@csgroup.eu
|
|
flush_tlb_page_nohash() was removed by
commit 703b41ad1a87 ("powerpc/mm: remove flush_tlb_page_nohash")
Remove stale prototype and comment.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/4a58831da6d6ba4fe309b94aa1dd8f02982d46b2.1603348103.git.christophe.leroy@csgroup.eu
|
|
On the same principle as commit 773edeadf672 ("powerpc/mm: Add mask
of possible MMU features"), add mask for MMU features that are
always there in order to optimise out dead branches.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/4943775fbe91885eb3e09133b093aaf62e55c715.1603348103.git.christophe.leroy@csgroup.eu
|
|
Commit bd59380c5ba4 ("powerpc/rtas: Restrict RTAS requests from userspace")
introduced the following error when invoking the errinjct userspace
tool:
[root@ltcalpine2-lp5 librtas]# errinjct open
[327884.071171] sys_rtas: RTAS call blocked - exploit attempt?
[327884.071186] sys_rtas: token=0x26, nargs=0 (called by errinjct)
errinjct: Could not open RTAS error injection facility
errinjct: librtas: open: Unexpected I/O error
The entry for ibm,open-errinjct in rtas_filter array has a typo where
the "j" is omitted in the rtas call name. After fixing this typo the
errinjct tool functions again as expected.
[root@ltcalpine2-lp5 linux]# errinjct open
RTAS error injection facility open, token = 1
Fixes: bd59380c5ba4 ("powerpc/rtas: Restrict RTAS requests from userspace")
Cc: [email protected]
Signed-off-by: Tyrel Datwyler <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/drivers
Driver changes for omaps for genpd for v5.11 merge window
This series of changes allows booting am335x with genpd and
device tree data without the legacy platform data. Also at
least am437x can be booted with gendp with power domain and
dts data. The SoC specific dts changes will be a separate
pull request.
We need the following driver changes merged before the dts
changes can be done:
- platform code needs a few improvments to probe l4_wkup first
for clocks, and to bail out when there is no platform data
- ti-sysc driver needs a non-urgent fix for asserting rstctrl
reset only after disabling the clocks, to probe modules with
no known control registers, and added quirk handling for gpmc
devices
- omap-prm driver needs a non-urgent fix for reset status bit,
support added for pm_clk, and then we add the rest of am335x
power domain data
- clock driver for am335x needs to keep l3_main clock enabled
with genpd for suspend and resume to work
- wkup_m3 remoteproc driver needs support added for reset
control if available instead of the legacy pdata callbacks
- pm33xx driver needs PM runtime support added for genpd
The am335x specific driver changes for the clock, wkup_m3,
pm33xx and remoteproc drivers are quite trivial and have not
caused merge conflicts in Linux next. I did not get acks for
these changes except from Santosh but had already pushed out
the branch already at that point. So I've added the related
driver maintainers to Cc.
* tag 'omap-for-v5.11/genpd-drivers-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
remoteproc/wkup_m3: Use reset control driver if available
soc: ti: pm33xx: Enable basic PM runtime support for genpd
soc: ti: omap-prm: am3: add genpd support for remaining PRM instances
soc: ti: omap-prm: Add pm_clk for genpd
clk: ti: am33xx: Keep am3 l3 main clock always on for genpd
bus: ti-sysc: Implement GPMC debug quirk to drop platform data
bus: ti-sysc: Support modules without control registers
ARM: OMAP2+: Probe PRCM first to probe l4_wkup with simple-pm-bus
ARM: OMAP2+: Check for inited flag
bus: ti-sysc: Assert reset only after disabling clocks
soc: ti: omap-prm: Do not check rstst bit on deassert if already deasserted
bus: ti-sysc: Fix bogus resetdone warning on enable for cpsw
bus: ti-sysc: Fix reset status check for modules with quirks
ARM: OMAP2+: Fix missing select PM_GENERIC_DOMAINS_OF
ARM: OMAP2+: Fix location for select PM_GENERIC_DOMAINS
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
A few more RGMII-ID fixes
* tag 'sunxi-fixes-for-5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: H5: NanoPi Neo Plus2: phy-mode rgmii-id
arm64: dts: allwinner: A64 Sopine: phy-mode rgmii-id
Link: https://lore.kernel.org/r/2a351c9c-470f-4c5e-ba37-80065ae0586d.lettre@localhost
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
arm64: dts: amlogic updates for v5.11, round 2
- audio support for several more boards
- PHY timing fixes
* tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson: add i2c3/rtc nodes and vrtc alias to GT-King/GT-King-Pro
arm64: dts: meson: g12b: w400: fix PHY deassert timing requirements
arm64: dts: meson: g12a: x96-max: fix PHY deassert timing requirements
ARM: dts: meson: fix PHY deassert timing requirements
arm64: dts: meson: fix PHY deassert timing requirements
arm64: dts: meson: g12b: odroid-n2: fix PHY deassert timing requirements
arm64: dts: meson: minor fixups for Khadas VIM/VIM2 dts
arm64: dts: meson: add audio playback to wetek-play2
arm64: dts: meson: add audio playback to wetek-hub
arm64: dts: meson: add audio playback to odroid-c2
arm64: dts: meson: add audio playback to nanopi-k2
arm64: dts: meson: add audio playback to khadas-vim2
arm64: dts: meson: add audio playback to khadas-vim
arm64: dts: meson: add audio playback to a95x
arm64: dts: meson-axg: add GE2D node
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.11, part three
1. S3C bindings and DTS cleanup,
2. Correct the clock rates for SPI0 in Artik 5 which is a fix for recently
introduced Ethernet on SPI on Artik 5 board.
* tag 'samsung-dt-5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Reduce assigned-clocks entries for SPI0 on Artik5 board
ARM: dts: s3c6410: correct SMDK6410 board compatible
ARM: dts: s3c24xx: add SMDK2416 board compatible
dt-bindings: arm: samsung: document S3C6410-based boards binding
dt-bindings: arm: samsung: document SMDK2416 board binding
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
Veyron backlight fix, another fix for dtbs-check and some additions
to the rk3288-based VMARC boards.
* tag 'v5.11-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add SDIO0 node for VMARC SOM
ARM: dts: rockchip: Add rtc node for VMARC SOM
ARM: dts: rockchip: rename wdt nodename to watchdog on rv1108
ARM: dts: rockchip: Remove 0 point from brightness-levels on rk3288-veyron
Link: https://lore.kernel.org/r/4582475.GXAFRqVoOG@phil
Signed-off-by: Arnd Bergmann <[email protected]>
|