| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
PowerVM will not arbitrarily oversubscribe or stop guests, page out the
guest kernel text to a NFS volume connected by carrier pigeon to abacus
based storage, etc., as a KVM host might. So PowerVM guests are not
likely to be killed by the hard lockup watchdog in normal operation,
even with shared processor LPARs which still get a minimum allotment of
CPU time.
Enable the hard lockup detector by default on !KVM guests, which we will
assume is PowerVM. It has been useful in finding problems on bare metal
kernels.
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The PPC_RFI_SRR_DEBUG check added by patch "powerpc/64s: avoid reloading
(H)SRR registers if they are still valid" has a few deficiencies. It
does not fix the actual problem, it's not enabled by default, and it
causes a program check interrupt which can cause more difficulties.
However there are a lot of paths which may clobber SRRs or change return
regs, and difficult to have a high confidence that all paths are covered
without wider testing.
Add a relatively low overhead always-enabled check that catches most
such cases, reports once, and fixes it so the kernel can continue.
Signed-off-by: Nicholas Piggin <[email protected]>
[mpe: Rebase, use switch & INT names, squash in race fix from Nick]
Signed-off-by: Michael Ellerman <[email protected]>
|
|
prep_irq_for_user_exit() has only one caller, squash it
inside that caller.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
prep_irq_for_user_exit() is a superset of
prep_irq_for_kernel_enabled_exit().
Rename prep_irq_for_kernel_enabled_exit() as prep_irq_for_enabled_exit()
and have prep_irq_for_user_exit() use it.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Nicholas Piggin <[email protected]>
Reviewed-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
prep_irq_for_user_exit() is a superset of
prep_irq_for_kernel_enabled_exit(). In order to allow refactoring in
following patch, interchange the two. This will allow
prep_irq_for_user_exit() to call a renamed version of
prep_irq_for_kernel_enabled_exit().
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Nicholas Piggin <[email protected]>
Reviewed-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
interrupt_exit_user_prepare() is a superset of
interrupt_exit_user_prepare_main().
Refactor to avoid code duplication.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Rename syscall_exit_prepare_main() into interrupt_exit_prepare_main()
Pass it the 'ret' so that it can 'or' it directly instead of
oring twice, once inside the function and once outside.
And remove 'r3' parameter which is not used.
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Nicholas Piggin <[email protected]>
Reviewed-by: Nicholas Piggin <[email protected]>
[np: split out some changes into other patches]
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Use the restart table facility to return from interrupt or system calls
without disabling MSR[EE] or MSR[RI].
Interrupt return asm is put into the low soft-masked region, to prevent
interrupts being processed here, although they are still taken as masked
interrupts which causes SRRs to be clobbered, and a pending soft-masked
interrupt to require replaying.
The return code uses restart table regions to redirct to a fixup handler
rather than continue with the exit, if such an interrupt happens. In
this case the interrupt return is redirected to a fixup handler which
reloads r1 for the interrupt stack and reloads registers and sets state
up to replay the soft-masked interrupt and try the exit again.
Some types of security exit fallback flushes and barriers are currently
unable to cope with reentrant interrupts, e.g., because they store some
state in the scratch SPR which would be clobbered even by masked
interrupts. For now the interrupts-enabled exits are disabled when these
flushes are used.
Signed-off-by: Nicholas Piggin <[email protected]>
[mpe: Guard unused exit_must_hard_disable() as reported by lkp]
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Treat code below __end_soft_masked as soft-masked for the purpose
of alternate return. 64s already mostly does this for scv entry.
This will be used to exit from interrupts without disabling MSR[EE].
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Prevent interrupt restore from allowing racing hard interrupts going
ahead of previous soft-pending ones, by using the soft-masked restart
handler to allow a store to clear the soft-mask while knowing nothing
is soft-pending.
This probably doesn't matter much in practice, but it's a simple
demonstrator / test case to exercise the restart table logic.
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The exception table fixup adjusts a failed page fault's interrupt return
location if it was taken at an address specified in the exception table,
to a corresponding fixup handler address.
Introduce a variation of that idea which adds a fixup table for NMIs and
soft-masked asynchronous interrupts. This will be used to protect
certain critical sections that are sensitive to being clobbered by
interrupts coming in (due to using the same SPRs and/or irq soft-mask
state).
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This frees up one more register (and takes advantage of that to
clean things up a little bit).
This register will be used in the following patch.
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This extends the MSR[RI]=0 window a little further into the system
call in order to pair RI and EE enabling with a single mtmsrd.
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The next patch would like to move interrupt return assembly code to a low
location before general text, so move it into its own file and include via
head_64.S
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
When an interrupt is taken, the SRR registers are set to return to where
it left off. Unless they are modified in the meantime, or the return
address or MSR are modified, there is no need to reload these registers
when returning from interrupt.
Introduce per-CPU flags that track the validity of SRR and HSRR
registers. These are cleared when returning from interrupt, when
using the registers for something else (e.g., OPAL calls), when
adjusting the return address or MSR of a context, and when context
switching (which changes the return address and MSR).
This improves the performance of interrupt returns.
Signed-off-by: Nicholas Piggin <[email protected]>
[mpe: Fold in fixup patch from Nick]
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This makes no real difference yet except that HSRR type interrupts will
use hrfid to return. This is important for the next patch.
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The msr argument is not used, remove it.
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
CONFIG_PPC_BOOK3S should be CONFIG_PPC_BOOK3S_64. restore_math is a
no-op for other configurations.
Signed-off-by: Christophe Leroy <[email protected]>
[np: split from another patch]
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Pass the value of linux_banner to firmware via option vector 7.
Option vector 7 is described in "LoPAR" Linux on Power Architecture
Reference v2.9, in table B.7 on page 824:
An ASCII character formatted null terminated string that describes
the client operating system. The string shall be human readable and
may be displayed on the console.
The string can be up to 256 bytes total, including the nul terminator.
linux_banner contains lots of information, and should make it possible
to identify the exact kernel version that is running:
const char linux_banner[] =
"Linux version " UTS_RELEASE " (" LINUX_COMPILE_BY "@"
LINUX_COMPILE_HOST ") (" LINUX_COMPILER ") " UTS_VERSION "\n";
For example:
Linux version 4.15.0-144-generic (buildd@bos02-ppc64el-018) (gcc
version 7.5.0 (Ubuntu 7.5.0-3ubuntu1~18.04)) #148-Ubuntu SMP Sat May 8
02:32:13 UTC 2021 (Ubuntu 4.15.0-144.148-generic 4.15.18)
It's also printed at boot to the console/dmesg, which should make it
possible to correlate what firmware receives with the console/dmesg on
the machine.
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
In a subsequent patch we'd like to have something like a strscpy_pad()
implementation usable in prom_init.c.
Currently we have a strcpy() implementation with only one caller, so
convert it into strscpy_pad() and update the caller.
Reviewed-by: Daniel Axtens <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
When using the Radix MMU our PGD is always 64K, and must be naturally
aligned.
For a 4K page size kernel that means page alignment of swapper_pg_dir is
not sufficient, leading to failure to boot.
Use the existing MAX_PTRS_PER_PGD which has the correct value, and
avoids us hard-coding 64K here.
Fixes: e72421a085a8 ("powerpc: Define swapper_pg_dir[] in C")
Reported-by: Daniel Axtens <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux into HEAD
- Support for the H_RPT_INVALIDATE hypercall
- Conversion of Book3S entry/exit to C
- Bug fixes
|
|
Pull in some more ppc KVM patches we are keeping in our topic branch.
In particular this brings in the series to add H_RPT_INVALIDATE.
|
|
LLVM does not emit optimal byteswap assembly, which results in high
stack usage in kvmhv_enter_nested_guest() due to the inlining of
byteswap_pt_regs(). With LLVM 12.0.0:
arch/powerpc/kvm/book3s_hv_nested.c:289:6: error: stack frame size of
2512 bytes in function 'kvmhv_enter_nested_guest' [-Werror,-Wframe-larger-than=]
long kvmhv_enter_nested_guest(struct kvm_vcpu *vcpu)
^
1 error generated.
While this gets fixed in LLVM, mark byteswap_pt_regs() as
noinline_for_stack so that it does not get inlined and break the build
due to -Werror by default in arch/powerpc/. Not inlining saves
approximately 800 bytes with LLVM 12.0.0:
arch/powerpc/kvm/book3s_hv_nested.c:290:6: warning: stack frame size of
1728 bytes in function 'kvmhv_enter_nested_guest' [-Wframe-larger-than=]
long kvmhv_enter_nested_guest(struct kvm_vcpu *vcpu)
^
1 warning generated.
Cc: [email protected] # v4.20+
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Nathan Chancellor <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://github.com/ClangBuiltLinux/linux/issues/1292
Link: https://bugs.llvm.org/show_bug.cgi?id=49610
Link: https://lore.kernel.org/r/[email protected]/
Link: https://gist.github.com/ba710e3703bf45043a31e2806c843ffd
Link: https://lore.kernel.org/r/[email protected]
|
|
In the nested KVM case, replace H_TLB_INVALIDATE by the new hcall
H_RPT_INVALIDATE if available. The availability of this hcall
is determined from "hcall-rpt-invalidate" string in ibm,hypertas-functions
DT property.
Signed-off-by: Bharata B Rao <[email protected]>
Reviewed-by: Fabiano Rosas <[email protected]>
Reviewed-by: David Gibson <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Now that we have H_RPT_INVALIDATE fully implemented, enable
support for the same via KVM_CAP_PPC_RPT_INVALIDATE KVM capability
Signed-off-by: Bharata B Rao <[email protected]>
Reviewed-by: David Gibson <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Enable support for process-scoped invalidations from nested
guests and partition-scoped invalidations for nested guests.
Process-scoped invalidations for any level of nested guests
are handled by implementing H_RPT_INVALIDATE handler in the
nested guest exit path in L0.
Partition-scoped invalidation requests are forwarded to the
right nested guest, handled there and passed down to L0
for eventual handling.
Signed-off-by: Bharata B Rao <[email protected]>
[aneesh: Nested guest partition-scoped invalidation changes]
Signed-off-by: Aneesh Kumar K.V <[email protected]>
[mpe: Squash in fixup patch]
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
H_RPT_INVALIDATE does two types of TLB invalidations:
1. Process-scoped invalidations for guests when LPCR[GTSE]=0.
This is currently not used in KVM as GTSE is not usually
disabled in KVM.
2. Partition-scoped invalidations that an L1 hypervisor does on
behalf of an L2 guest. This is currently handled
by H_TLB_INVALIDATE hcall and this new replaces the old that.
This commit enables process-scoped invalidations for L1 guests.
Support for process-scoped and partition-scoped invalidations
from/for nested guests will be added separately.
Process scoped tlbie invalidations from L1 and nested guests
need RS register for TLBIE instruction to contain both PID and
LPID. This patch introduces primitives that execute tlbie
instruction with both PID and LPID set in prepartion for
H_RPT_INVALIDATE hcall.
A description of H_RPT_INVALIDATE follows:
int64 /* H_Success: Return code on successful completion */
/* H_Busy - repeat the call with the same */
/* H_Parameter, H_P2, H_P3, H_P4, H_P5 : Invalid
parameters */
hcall(const uint64 H_RPT_INVALIDATE, /* Invalidate RPT
translation
lookaside information */
uint64 id, /* PID/LPID to invalidate */
uint64 target, /* Invalidation target */
uint64 type, /* Type of lookaside information */
uint64 pg_sizes, /* Page sizes */
uint64 start, /* Start of Effective Address (EA)
range (inclusive) */
uint64 end) /* End of EA range (exclusive) */
Invalidation targets (target)
-----------------------------
Core MMU 0x01 /* All virtual processors in the
partition */
Core local MMU 0x02 /* Current virtual processor */
Nest MMU 0x04 /* All nest/accelerator agents
in use by the partition */
A combination of the above can be specified,
except core and core local.
Type of translation to invalidate (type)
---------------------------------------
NESTED 0x0001 /* invalidate nested guest partition-scope */
TLB 0x0002 /* Invalidate TLB */
PWC 0x0004 /* Invalidate Page Walk Cache */
PRT 0x0008 /* Invalidate caching of Process Table
Entries if NESTED is clear */
PAT 0x0008 /* Invalidate caching of Partition Table
Entries if NESTED is set */
A combination of the above can be specified.
Page size mask (pages)
----------------------
4K 0x01
64K 0x02
2M 0x04
1G 0x08
All sizes (-1UL)
A combination of the above can be specified.
All page sizes can be selected with -1.
Semantics: Invalidate radix tree lookaside information
matching the parameters given.
* Return H_P2, H_P3 or H_P4 if target, type, or pageSizes parameters
are different from the defined values.
* Return H_PARAMETER if NESTED is set and pid is not a valid nested
LPID allocated to this partition
* Return H_P5 if (start, end) doesn't form a valid range. Start and
end should be a valid Quadrant address and end > start.
* Return H_NotSupported if the partition is not in running in radix
translation mode.
* May invalidate more translation information than requested.
* If start = 0 and end = -1, set the range to cover all valid
addresses. Else start and end should be aligned to 4kB (lower 11
bits clear).
* If NESTED is clear, then invalidate process scoped lookaside
information. Else pid specifies a nested LPID, and the invalidation
is performed on nested guest partition table and nested guest
partition scope real addresses.
* If pid = 0 and NESTED is clear, then valid addresses are quadrant 3
and quadrant 0 spaces, Else valid addresses are quadrant 0.
* Pages which are fully covered by the range are to be invalidated.
Those which are partially covered are considered outside
invalidation range, which allows a caller to optimally invalidate
ranges that may contain mixed page sizes.
* Return H_SUCCESS on success.
Signed-off-by: Bharata B Rao <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add a field to mmu_psize_def to store the page size encodings
of H_RPT_INVALIDATE hcall. Initialize this while scanning the radix
AP encodings. This will be used when invalidating with required
page size encoding in the hcall.
Signed-off-by: Bharata B Rao <[email protected]>
Reviewed-by: David Gibson <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The type values H_RPTI_TYPE_PRT and H_RPTI_TYPE_PAT indicate
invalidating the caching of process and partition scoped entries
respectively.
Signed-off-by: Aneesh Kumar K.V <[email protected]>
Signed-off-by: Bharata B Rao <[email protected]>
Reviewed-by: David Gibson <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This allows microwatt's kernel to be built with an embedded device tree.
Load to arch/powerpc/boot/dtbImage.microwatt to 0x500000:
mw_debug -b fpga stop load arch/powerpc/boot/dtbImage.microwatt 500000 start
Signed-off-by: Joel Stanley <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
Reviewed-by: Segher Boessenkool <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This fixes the core devtree.c functions and the ns16550 UART backend.
Signed-off-by: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
Reviewed-by: Segher Boessenkool <[email protected]>
Acked-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Signed-off-by: Paul Mackerras <[email protected]>
Reviewed-by: Segher Boessenkool <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Microwatt's hardware RNG is accessed using the DARN instruction.
Signed-off-by: Paul Mackerras <[email protected]>
Reviewed-by: Nicholas Piggin <[email protected]>
Reviewed-by: Segher Boessenkool <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/YMwXPHlV/[email protected]
|
|
This adds support to the Microwatt platform to use the standard
16550-style UART which available in the standalone Microwatt FPGA.
Signed-off-by: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
Reviewed-by: Segher Boessenkool <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This is a simple native ICS backend that matches the layout of
the Microwatt implementation of ICS.
Signed-off-by: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
Reviewed-by: Segher Boessenkool <[email protected]>
[mpe: Add empty ics_native_init() to unbreak non-microwatt builds]
Signed-off-by: Michael Ellerman <[email protected]>
fixup-ics
Link: https://lore.kernel.org/r/[email protected]
|
|
Just like any other embedded platform.
Add an empty soc node.
Signed-off-by: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
Reviewed-by: Segher Boessenkool <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/YMwWx98+PMibZq/[email protected]
|
|
Microwatt currently runs with MSR[HV] = 0, hence the usable-privilege
properties don't have bit 2 (for HV support) set, and we need the
/chosen/ibm,architecture-vec-5 property.
Signed-off-by: Paul Mackerras <[email protected]>
Reviewed-by: Segher Boessenkool <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Microwatt is a FPGA-based implementation of the Power ISA. It
currently only implements little-endian 64-bit mode, and does
not (yet) support SMP, VMX, VSX or transactional memory. It has an
optional FPU, and an optional MMU (required for running Linux,
obviously) which implements a configurable radix tree but not
hypervisor mode or nested radix translation.
This adds a new machine type to support FPGA-based SoCs with a
Microwatt core. CONFIG_MATH_EMULATION can be selected for Microwatt
SOCs which don't have the FPU.
Signed-off-by: Paul Mackerras <[email protected]>
Reviewed-by: Nicholas Piggin <[email protected]>
Reviewed-by: Segher Boessenkool <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Use set_memory_attr() instead of the PPC32 specific change_page_attr()
change_page_attr() was checking that the address was not mapped by
blocks and was handling highmem, but that's unneeded because the
affected pages can't be in highmem and block mapping verification
is already done by the callers.
Signed-off-by: Christophe Leroy <[email protected]>
[ruscur: rebase on powerpc/merge with Christophe's new patches]
Signed-off-by: Russell Currey <[email protected]>
Signed-off-by: Jordan Niethe <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
In addition to the set_memory_xx() functions which allows to change
the memory attributes of not (yet) used memory regions, implement a
set_memory_attr() function to:
- set the final memory protection after init on currently used
kernel regions.
- enable/disable kernel memory regions in the scope of DEBUG_PAGEALLOC.
Unlike the set_memory_xx() which can act in three step as the regions
are unused, this function must modify 'on the fly' as the kernel is
executing from them. At the moment only PPC32 will use it and changing
page attributes on the fly is not an issue.
Reported-by: kbuild test robot <[email protected]>
[ruscur: cast "data" to unsigned long instead of int]
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Russell Currey <[email protected]>
Signed-off-by: Jordan Niethe <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
To enable strict module RWX on powerpc, set:
CONFIG_STRICT_MODULE_RWX=y
You should also have CONFIG_STRICT_KERNEL_RWX=y set to have any real
security benefit.
ARCH_HAS_STRICT_MODULE_RWX is set to require ARCH_HAS_STRICT_KERNEL_RWX.
This is due to a quirk in arch/Kconfig and arch/powerpc/Kconfig that
makes STRICT_MODULE_RWX *on by default* in configurations where
STRICT_KERNEL_RWX is *unavailable*.
Since this doesn't make much sense, and module RWX without kernel RWX
doesn't make much sense, having the same dependencies as kernel RWX
works around this problem.
Book3s/32 603 and 604 core processors are not able to write protect
kernel pages so do not set ARCH_HAS_STRICT_MODULE_RWX for Book3s/32.
[jpn: - predicate on !PPC_BOOK3S_604
- make module_alloc() use PAGE_KERNEL protection]
Signed-off-by: Russell Currey <[email protected]>
Signed-off-by: Jordan Niethe <[email protected]>
Reviewed-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add the necessary call to bpf_jit_binary_lock_ro() to remove write and
add exec permissions to the JIT image after it has finished being
written.
Without CONFIG_STRICT_MODULE_RWX the image will be writable and
executable until the call to bpf_jit_binary_lock_ro().
Signed-off-by: Jordan Niethe <[email protected]>
Reviewed-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Commit 74451e66d516 ("bpf: make jited programs visible in traces") added
a default bpf_jit_free() implementation. Powerpc did not use the default
bpf_jit_free() as powerpc did not set the images read-only. The default
bpf_jit_free() called bpf_jit_binary_unlock_ro() is why it could not be
used for powerpc.
Commit d53d2f78cead ("bpf: Use vmalloc special flag") moved keeping
track of read-only memory to vmalloc. This included removing
bpf_jit_binary_unlock_ro(). Therefore there is no reason powerpc needs
its own bpf_jit_free(). Remove it.
Signed-off-by: Jordan Niethe <[email protected]>
Reviewed-by: Christophe Leroy <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add the arch specific insn page allocator for powerpc. This allocates
ROX pages if STRICT_KERNEL_RWX is enabled. These pages are only written
to with patch_instruction() which is able to write RO pages.
Signed-off-by: Russell Currey <[email protected]>
Signed-off-by: Christophe Leroy <[email protected]>
[jpn: Reword commit message, switch to __vmalloc_node_range()]
Signed-off-by: Jordan Niethe <[email protected]>
Reviewed-by: Daniel Axtens <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Make module_alloc() use PAGE_KERNEL protections instead of
PAGE_KERNEL_EXEX if Strict Module RWX is enabled.
Signed-off-by: Jordan Niethe <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
setup_text_poke_area() is a late init call so it runs before
mark_rodata_ro() and after the init calls. This lets all the init code
patching simply write to their locations. In the future, kprobes is
going to allocate its instruction pages RO which means they will need
setup_text__poke_area() to have been already called for their code
patching. However, init_kprobes() (which allocates and patches some
instruction pages) is an early init call so it happens before
setup_text__poke_area().
start_kernel() calls poking_init() before any of the init calls. On
powerpc, poking_init() is currently a nop. setup_text_poke_area() relies
on kernel virtual memory, cpu hotplug and per_cpu_areas being setup.
setup_per_cpu_areas(), boot_cpu_hotplug_init() and mm_init() are called
before poking_init().
Turn setup_text_poke_area() into poking_init().
Signed-off-by: Jordan Niethe <[email protected]>
Reviewed-by: Christophe Leroy <[email protected]>
Reviewed-by: Russell Currey <[email protected]>
[mpe: Fold in missing prototype for poking_init() from lkp]
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The set_memory_{ro/rw/nx/x}() functions are required for
STRICT_MODULE_RWX, and are generally useful primitives to have. This
implementation is designed to be generic across powerpc's many MMUs.
It's possible that this could be optimised to be faster for specific
MMUs.
This implementation does not handle cases where the caller is attempting
to change the mapping of the page it is executing from, or if another
CPU is concurrently using the page being altered. These cases likely
shouldn't happen, but a more complex implementation with MMU-specific code
could safely handle them.
On hash, the linear mapping is not kept in the linux pagetable, so this
will not change the protection if used on that range. Currently these
functions are not used on the linear map so just WARN for now.
apply_to_existing_page_range() does not work on huge pages so for now
disallow changing the protection of huge pages.
[jpn: - Allow set memory functions to be used without Strict RWX
- Hash: Disallow certain regions
- Have change_page_attr() take function pointers to manipulate ptes
- Radix: Add ptesync after set_pte_at()]
Signed-off-by: Russell Currey <[email protected]>
Signed-off-by: Christophe Leroy <[email protected]>
Signed-off-by: Jordan Niethe <[email protected]>
Reviewed-by: Daniel Axtens <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This allows the hypervisor / firmware to describe this workarounds to
the guest.
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Rather than tying this mitigation to RFI L1D flush requirement, add a
new bit for it.
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|