| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
0x08 is the HT capability, while PCI_CAP_ID_HT_IRQCONF would be
the subtype 0x80 that mpic_scan_ht_pic() uses.
Rename PCI_CAP_ID_HT_IRQCONF into PCI_CAP_ID_HT.
And by the way, use it in the ipath driver instead of defining its
own HT_CAPABILITY_ID.
Signed-off-by: Brice Goglin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This patch causes fsl_soc.h to import the definition of phys_addr_t
itself, rather than relying on its includer to do so.
Signed-off-by: Scott Wood <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
This patch fixes the assignment of pending registers to IRQ numbers for
the IPIC; the code previously assigned all IRQs to the high pending word
regardless of which word the interrupt belonged to.
Signed-off-by: Scott Wood <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
|
|
It seems that the occasional data corruption observed with the tg3
driver wasn't due to missing barriers after all, but rather seems to
be due to the DART (= IOMMU) in the U4 northbridge reading stale
IOMMU table entries from memory due to a race. This fixes it by
making the CPU read the entry back from memory before using it.
Signed-off-by: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
|
|
This adds a new hardware information table for mpic. This enables
the mpic code to deal with mpic controllers with different register
layouts and hardware behaviours.
This introduces CONFIG_MPIC_WEIRD. For boards with non standard mpic
controllers, select CONFIG_MPIC_WEIRD and add its hardware information
in the mpic_infos[] array.
TSI108/109 PIC takes the first index of weird hardware information
table. :) The table can be extended. The Tsi108/109 PIC looks like
standard OpenPIC but, in fact, is different in register mapping and
behavior.
The patch does not affect the behavior of standard mpic. If
CONFIG_MPIC_WEIRD is not defined, the code is essentially identical to
the current code.
[[email protected]:
This patch is a slightly cleaned up version of Zang Roy's support for
the TSI108 MPIC variant. It also fixes up MPC7448_hpc2 to use the new
version of the type macros and changes the way MPIC is selected in
Kconfig to better match what is done for other system devices.
]
Signed-off-by: Roy Zang <[email protected]>
Signed-off-by: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
set IRQ sense
This converts ipic code to Benh's IRQ mods. For the IPIC, IRQ sense values in the device tree equal those in include/linux/irq.h; that's 8 for low assertion (most internal IRQs on mpc83xx), and 2 for high-to-low change.
spinlocks added to [un]mask, ack operations; default handler and type now set in host_map; and redundant condition check eliminated.
Signed-off-by: Kim Phillips <[email protected]>
Signed-off-by: Li Yang <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Keep from breaking 83xx arch/ppc build. Back up old school arch/powerpc/sysdev/ipic.[hc] to arch/ppc/syslib.
Signed-off-by: Kim Phillips <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
|
|
The patch rewrites mpc7448hpc2 board irq support according to the new
mpic device tree interface.
Signed-off-by: Roy Zang <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
IRQ setup now comes from the Flat Device Tree and use the new generic
IRQ code. Fixed the fsl_soc.c IRQ OF interrupt node parsing.
Removed some unused MPC86xx macro definition.
Signed-off-by: Zhang Wei <[email protected]>
Signed-off-by: Jon Loeliger <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
(cherry picked from 919fede6edab94cccb3ca8c1c0b32fa62c9369a5 commit)
|
|
Also accept "local-mac-address". However the old "address"
is now obsolete, but accepted for backwards compatibility.
It should be removed after all device trees have been
converted to use "mac-address".
Signed-off-by: Jon Loeliger <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
We don't have much in the way of doc comments, but some of those we do have
don't work because they start with "/***" or "/*", not "/**" which is what
kernel-doc requires.
Signed-off-by: Michael Ellerman <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
IRQ setup now comes from the Flat Device Tree and use the new generic
IRQ code. Fixed the fsl_soc.c IRQ OF interrupt node parsing.
Removed some unused MPC86xx macro definition.
Signed-off-by: Zhang Wei <[email protected]>
Signed-off-by: Jon Loeliger <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
|
|
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.
tsi108 driver changes.
Signed-off-by: Jeremy Kerr <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.
powerpc core changes.
Signed-off-by: Jeremy Kerr <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
The quad g5 currently doesn't boot due to two problems. This patch fixes the
first one: Apple new way of doing interrupt specifiers in OF for devices using
the HT APIC isn't properly parsed by the new MPIC driver code.
Signed-off-by: Benjamin Herrenschmidt <[email protected]>
Cc: Paul Mackerras <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
This patch slightly reworks the new irq code to fix a small design error. I
removed the passing of the trigger to the map() calls entirely, it was not a
good idea to have one call do two different things. It also fixes a couple of
corner cases.
Mapping a linux virtual irq to a physical irq now does only that. Setting the
trigger is a different action which has a different call.
The main changes are:
- I no longer call host->ops->map() for an already mapped irq, I just return
the virtual number that was already mapped. It was called before to give an
opportunity to change the trigger, but that was causing issues as that could
happen while the interrupt was in use by a device, and because of the
trigger change, map would potentially muck around with things in a racy way.
That was causing much burden on a given's controller implementation of
map() to get it right. This is much simpler now. map() is only called on
the initial mapping of an irq, meaning that you know that this irq is _not_
being used. You can initialize the hardware if you want (though you don't
have to).
- Controllers that can handle different type of triggers (level/edge/etc...)
now implement the standard irq_chip->set_type() call as defined by the
generic code. That means that you can use the standard set_irq_type() to
configure an irq line manually if you wish or (though I don't like that
interface), pass explicit trigger flags to request_irq() as defined by the
generic kernel interfaces. Also, using those interfaces guarantees that
your controller set_type callback is called with the descriptor lock held,
thus providing locking against activity on the same interrupt (including
mask/unmask/etc...) automatically. A result is that, for example, MPIC's
own map() implementation calls irq_set_type(NONE) to configure the hardware
to the default triggers.
- To allow the above, the irq_map array entry for the new mapped interrupt
is now set before map() callback is called for the controller.
- The irq_create_of_mapping() (also used by irq_of_parse_and_map()) function
for mapping interrupts from the device-tree now also call the separate
set_irq_type(), and only does so if there is a change in the trigger type.
- While I was at it, I changed pci_read_irq_line() (which is the helper I
would expect most archs to use in their pcibios_fixup() to get the PCI
interrupt routing from the device tree) to also handle a fallback when the
DT mapping fails consisting of reading the PCI_INTERRUPT_PIN to know wether
the device has an interrupt at all, and the the PCI_INTERRUPT_LINE to get an
interrupt number from the device. That number is then mapped using the
default controller, and the trigger is set to level low. That default
behaviour works for several platforms that don't have a proper interrupt
tree like Pegasos. If it doesn't work for your platform, then either
provide a proper interrupt tree from the firmware so that fallback isn't
needed, or don't call pci_read_irq_line()
- Add back a bit that got dropped by my main rework patch for properly
clearing pending IPIs on pSeries when using a kexec
Signed-off-by: Benjamin Herrenschmidt <[email protected]>
Cc: Paul Mackerras <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
With the new interrupt rework, an interrupt "host" map() callback can be
called after the interrupt is already active.
It's called again for an already mapped interrupt to allow changing the
trigger setup, and currently this is not guarded with a test of wether
the interrupt is requested or not.
I plan to change some of this logic to be a bit less lenient against
random reconfiguring of live interrupts but just not yet.
The ported MPIC driver has a bug where when that happens, it will mask
the interrupt. This changes it to preserve the previous masking of the
interrupt instead.
Signed-off-by: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
This adds the new irq remapper core and removes the old one. Because
there are some fundamental conflicts with the old code, like the value
of NO_IRQ which I'm now setting to 0 (as per discussions with Linus),
etc..., this commit also changes the relevant platform and driver code
over to use the new remapper (so as not to cause difficulties later
in bisecting).
This patch removes the old pre-parsing of the open firmware interrupt
tree along with all the bogus assumptions it made to try to renumber
interrupts according to the platform. This is all to be handled by the
new code now.
For the pSeries XICS interrupt controller, a single remapper host is
created for the whole machine regardless of how many interrupt
presentation and source controllers are found, and it's set to match
any device node that isn't a 8259. That works fine on pSeries and
avoids having to deal with some of the complexities of split source
controllers vs. presentation controllers in the pSeries device trees.
The powerpc i8259 PIC driver now always requests the legacy interrupt
range. It also has the feature of being able to match any device node
(including NULL) if passed no device node as an input. That will help
porting over platforms with broken device-trees like Pegasos who don't
have a proper interrupt tree.
Signed-off-by: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
This copies the i8259 interrupt controller driver from arch/powerpc
to arch/ppc. It's currently shared by both architectures, but the upcoming
arch/powerpc interrupt changes will break the arch/ppc builds. The changes
are too important to just use #ifdef's in the driver.
Signed-off-by: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
This adapts the generic powerpc interrupt handling code, and all of
the platforms except for the embedded 6xx machines, to use the new
genirq framework.
Signed-off-by: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Use the new IRQF_ constants and remove the SA_INTERRUPT define
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: "David S. Miller" <[email protected]>
Cc: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Signed-off-by: Jörn Engel <[email protected]>
Signed-off-by: Adrian Bunk <[email protected]>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (43 commits)
[POWERPC] Use little-endian bit from firmware ibm,pa-features property
[POWERPC] Make sure smp_processor_id works very early in boot
[POWERPC] U4 DART improvements
[POWERPC] todc: add support for Time-Of-Day-Clock
[POWERPC] Make lparcfg.c work when both iseries and pseries are selected
[POWERPC] Fix idr locking in init_new_context
[POWERPC] mpc7448hpc2 (taiga) board config file
[POWERPC] Add tsi108 pci and platform device data register function
[POWERPC] Add general support for mpc7448hpc2 (Taiga) platform
[POWERPC] Correct the MAX_CONTEXT definition
powerpc: minor cleanups for mpc86xx
[POWERPC] Make sure we select CONFIG_NEW_LEDS if ADB_PMU_LED is set
[POWERPC] Simplify the code defining the 64-bit CPU features
[POWERPC] powerpc: kconfig warning fix
[POWERPC] Consolidate some of kernel/misc*.S
[POWERPC] Remove unused function call_with_mmu_off
[POWERPC] update asm-powerpc/time.h
[POWERPC] Clean up it_lp_queue.h
[POWERPC] Skip the "copy down" of the kernel if it is already at zero.
[POWERPC] Add the use of the firmware soft-reset-nmi to kdump.
...
|
|
Consolidation: remove the irq_affinity[NR_IRQS] array and move it into the
irq_desc[NR_IRQS].affinity field.
[[email protected]: sparc64 build fix]
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
This patch-queue improves the generic IRQ layer to be truly generic, by adding
various abstractions and features to it, without impacting existing
functionality.
While the queue can be best described as "fix and improve everything in the
generic IRQ layer that we could think of", and thus it consists of many
smaller features and lots of cleanups, the one feature that stands out most is
the new 'irq chip' abstraction.
The irq-chip abstraction is about describing and coding and IRQ controller
driver by mapping its raw hardware capabilities [and quirks, if needed] in a
straightforward way, without having to think about "IRQ flow"
(level/edge/etc.) type of details.
This stands in contrast with the current 'irq-type' model of genirq
architectures, which 'mixes' raw hardware capabilities with 'flow' details.
The patchset supports both types of irq controller designs at once, and
converts i386 and x86_64 to the new irq-chip design.
As a bonus side-effect of the irq-chip approach, chained interrupt controllers
(master/slave PIC constructs, etc.) are now supported by design as well.
The end result of this patchset intends to be simpler architecture-level code
and more consolidation between architectures.
We reused many bits of code and many concepts from Russell King's ARM IRQ
layer, the merging of which was one of the motivations for this patchset.
This patch:
rename desc->handler to desc->chip.
Originally i did not want to do this, because it's a big patch. But having
both "desc->handler", "desc->handle_irq" and "action->handler" caused a
large degree of confusion and made the code appear alot less clean than it
truly is.
I have also attempted a dual approach as well by introducing a
desc->chip alias - but that just wasnt robust enough and broke
frequently.
So lets get over with this quickly. The conversion was done automatically
via scripts and converts all the code in the kernel.
This renaming patch is the first one amongst the patches, so that the
remaining patches can stay flexible and can be merged and split up
without having some big monolithic patch act as a merge barrier.
[[email protected]: build fix]
[[email protected]: another build fix]
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Better late than never...
Respin based on previous comment. Only remaining issue last time was an
extra mb() that I've taken out.
Signed-off-by: Paul Mackerras <[email protected]>
|
|
This is a resubmit with a proper subject and with all comments addressed.
Applies cleanly to powerpc.git 649e85797259162f7fdc696420e7492f20226f2d
Mark
--
The todc code from arch/ppc supports many todc/rtc chips and is needed
in arch/powerpc. This patch adds the todc code to arch/powerpc.
Signed-off-by: Mark A. Greer <[email protected]>
--
arch/powerpc/Kconfig | 7
arch/powerpc/sysdev/Makefile | 1
arch/powerpc/sysdev/todc.c | 392 ++++++++++++++++++++++++++++++++++
include/asm-powerpc/todc.h | 487 +++++++++++++++++++++++++++++++++++++++++++
4 files changed, 887 insertions(+)
--
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Add Tundra Semiconductor tsi108 pci and platform device data register
function support.
Signed-off-by: Alexandre Bounine <[email protected]>
Signed-off-by: Roy Zang <[email protected]>
---
Signed-off-by: Paul Mackerras <[email protected]>
|
|
locking init cleanups:
- convert " = SPIN_LOCK_UNLOCKED" to spin_lock_init() or DEFINE_SPINLOCK()
- convert rwlocks in a similar manner
this patch was generated automatically.
Motivation:
- cleanliness
- lockdep needs control of lock initialization, which the open-coded
variants do not give
- it's also useful for -rt and for lock debugging in general
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Arjan van de Ven <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (139 commits)
[POWERPC] re-enable OProfile for iSeries, using timer interrupt
[POWERPC] support ibm,extended-*-frequency properties
[POWERPC] Extra sanity check in EEH code
[POWERPC] Dont look for class-code in pci children
[POWERPC] Fix mdelay badness on shared processor partitions
[POWERPC] disable floating point exceptions for init
[POWERPC] Unify ppc syscall tables
[POWERPC] mpic: add support for serial mode interrupts
[POWERPC] pseries: Print PCI slot location code on failure
[POWERPC] spufs: one more fix for 64k pages
[POWERPC] spufs: fail spu_create with invalid flags
[POWERPC] spufs: clear class2 interrupt status before wakeup
[POWERPC] spufs: fix Makefile for "make clean"
[POWERPC] spufs: remove stop_code from struct spu
[POWERPC] spufs: fix spu irq affinity setting
[POWERPC] spufs: further abstract priv1 register access
[POWERPC] spufs: split the Cell BE support into generic and platform dependant parts
[POWERPC] spufs: dont try to access SPE channel 1 count
[POWERPC] spufs: use kzalloc in create_spu
[POWERPC] spufs: fix initial state of wbox file
...
Manually resolved conflicts in:
drivers/net/phy/Makefile
include/asm-powerpc/spu.h
|
|
In some systems we may have both a platform EHCI controller and PCI EHCI
controller. Previously we couldn't build the EHCI support as a module due
to conflicting module_init() calls in the code.
Signed-off-by: Kumar Gala <[email protected]>
Signed-off-by: David Brownell <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
On Tue, Jun 20, 2006 at 02:01:26PM +1000, Benjamin Herrenschmidt wrote:
> On Mon, 2006-06-19 at 13:08 -0700, Mark A. Greer wrote:
> > MPC10x-style interrupt controllers have a serial mode that allows
> > several interrupts to be clocked in through one INT signal.
> >
> > This patch adds the software support for that mode.
>
> You hard code the clock ratio... why not add a separate call to be
> called after mpic_init,
> something like mpic_set_serial_int(int mpic, int enable, int
> clock_ratio) ?
How's this?
--
MPC10x-style interrupt controllers have a serial mode that allows
several interrupts to be clocked in through one INT signal.
This patch adds the software support for that mode.
Signed-off-by: Mark A. Greer <[email protected]>
--
arch/powerpc/sysdev/mpic.c | 20 ++++++++++++++++++++
include/asm-powerpc/mpic.h | 10 ++++++++++
2 files changed, 30 insertions(+)
--
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Allocate IOMMU tables local to the relevant node.
Signed-off-by: Anton Blanchard <[email protected]>
Acked-by: Olof Johansson <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Micro-optimisation - add no-minimal-toc to some more arch/powerpc Makefiles.
Signed-off-by: Anton Blanchard <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Turn on the DART already at 1GB. This is needed because of crippled
devices in some systems, i.e. Airport Extreme cards, only supporting
30-bit DMA addresses.
Otherwise, users with between 1 and 2GB of memory will need to manually
enable it with iommu=force, and that's no good.
Some simple performance tests show that there's a slight impact of
enabling DART, but it's in the 1-3% range (kernel build with disk I/O
as well as over NFS).
iommu=off can still be used for those who don't want to deal with the
overhead (and don't need it for any devices).
Signed-off-by: Olof Johansson <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
|
|
Do disable, not enable, the HT APIC IRQ in the function that is
supposed to.
Enable the MPIC IRQ before enabling the downstream APIC IRQ, avoids
potentially losing an interrupt.
Signed-off-by: Segher Boessenkool <[email protected]>
Acked-by: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
This patch removes all self references and fixes references to files
in the now defunct arch/ppc64 tree. I think this accomplises
everything wanted, though there might be a few references I missed.
Signed-off-by: Jon Mason <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
|
|
it's int __iomem *, not int * __iomem...
Signed-off-by: Al Viro <[email protected]>
|
|
Setup the platform devices needed by the Freescale EHCI USB
host controllers based on a flat device tree
Signed-off-by: Kumar Gala <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Currently most callers of lmb_alloc() don't check if it worked or not, if it
ever does weird bad things will probably happen. The few callers who do check
just panic or BUG_ON.
So make lmb_alloc() panic internally, to catch bugs at the source. The few
callers who did check the result no longer need to.
The only caller that did anything interesting with the return result was
careful_allocation(). For it we create __lmb_alloc_base() which _doesn't_ panic
automatically, a little messy, but passable.
Signed-off-by: Michael Ellerman <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Cleaned up fsl_soc.c based on comments from Olof Johansson. Ran through
Lindent, and split gfar_mdio init into its own function.
Signed-off-by: Kumar Gala <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Parse the flat device tree for devices on Freescale SOC's that we know
about (gianfar, gianfar_mdio, i2c, mpc83xx_wdt). We need to setup
platform devices and platform data for these devices to match arch/ppc
usage.
Also add a helper function (get_immrbase) that reports the base
address of the MMIO registers on the SOC.
Signed-off-by: Kumar Gala <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Rpn is assigned every time in the loop, no need to increase it too.
Signed-off-by: Olof Johansson <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|
|
Updated Kconfig & Makefiles in prep for adding support for the Freescale
MPC83xx family of processors to arch/powerpc. Moved around some config
options that are more globally applicable to other PowerPC processors.
Added a temporary config option (83xx) to match existing arch/ppc support
for the MPC83xx line.
Signed-off-by: Kumar Gala <[email protected]>
Signed-off-by: Paul Mackerras <[email protected]>
|