| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Adapt at91_pm_backup_init() to work for SAMA7G5. Also, set the LPM pin
to shutdown controller. This will signal to PMIC that it needs to switch
to the state corresponding to backup mode.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The resuming from backup mode is done with the help of bootloader.
The bootloader reconfigure the DDR controller and DDR PHY controller.
To speed-up the resuming process save the PHY calibration data into
SECURAM before suspending (securam is powered on backup mode).
This data will be later used by bootloader in DDR PHY reconfiguration
process. Also, in the process or recalibration the first 8 words of
the memory may get corrupted. To solve this, these 8 words are saved
in the securam and restored by bootloader in the process of PHY
configuration.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
SAMA7G5 self-refresh procedure accesses also the DDR PHY registers.
Adapt the code so that the at91_dt_ramc() to look also for DDR PHYs,
in case it is mandatory.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add SAMA7G5 DDR controller to the list of DDR controller compatibles.
At the moment there is no standby support. Adapt the code for this.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Wait for DDR power mode off before shutting down the core.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add support to disable/enable 2.5V LDO regulator when entering/exiting
any ULP mode.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add support for MCK1..4 save restore for ULP modes.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add self-refresh support for SAMA7G5.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
SAMA7G5 has 5 master clocks 0..4. MCK0 is controlled differently than
MCK 1..4. MCK 1..4 should also be saved/restored in the last phase of
suspend/resume. Thus, adapt wait_mckrdy to support also MCK1..4.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Replace CONFIG_SOC_SAM9X60 with CONFIG_HAVE_AT91_SAM9X60_PLL as the
SAM9X60's PLL is also present on SAMA7G5.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
For the previous AT91 RAM controller and self-refresh procedure this
had no side effects. However, for SAMA7G5 the self-refresh procedure
doesn't allow this anymore as the RAM controller ports are closed
before switching it to self-refresh. This commits prepares the code
for the following ones adding self-refresh and PM support for SAMA7G5.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Use r7 instead of tmp1 in macros. This prepares the filed for
next commits.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
There is no need to initialize pdev.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
at91_pm_modes_init() checks for proper nodes in device tree and maps
them accordingly. Up to SAMA7G5 all AT91 SoCs had the same mapping
b/w power saving modes and different controllers needed in the
final/first steps of suspend/resume. SAMA7G5 is not aligned with the
old SoCs thus the code is adapted for this. This patch prepares
the field for next commits.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Document at91_soc_pm structure.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Move the setup of soc_pm.bu->suspended in platform_suspend::begin
function so that the PMC code in charge with clocks suspend/resume
to differentiate b/w standard PM mode and backup mode.
Signed-off-by: Claudiu Beznea <[email protected]>
Reviewed-by: Alexandre Belloni <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Move pm_bu to soc_pm data structure.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add new SoC from at91 family : sama7g5
Signed-off-by: Eugen Hristev <[email protected]>
[[email protected]: Select PLL, generic clock and UTMI support, add PM configs]
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Link: https://lore.kernel.org/r/[email protected]
|
|
Both the caller and the supplier's source file should have access to
the include file containing the prototypes.
Fixes the following W=1 kernel build warning(s):
drivers/pinctrl/pinctrl-at91.c:1637:6: warning: no previous prototype for ‘at91_pinctrl_gpio_suspend’ [-Wmissing-prototypes]
1637 | void at91_pinctrl_gpio_suspend(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/pinctrl-at91.c:1661:6: warning: no previous prototype for ‘at91_pinctrl_gpio_resume’ [-Wmissing-prototypes]
1661 | void at91_pinctrl_gpio_resume(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~
Cc: Russell King <[email protected]>
Cc: Nicolas Ferre <[email protected]>
Cc: Alexandre Belloni <[email protected]>
Cc: Ludovic Desroches <[email protected]>
Signed-off-by: Lee Jones <[email protected]>
Acked-by: Linus Walleij <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Compiling with the clang integrated assembler warns about
a recently added instruction:
<instantiation>:14:13: error: unknown token in expression
ldr tmp1, =#0x00020010UL
arch/arm/mach-at91/pm_suspend.S:542:2: note: while in macro instantiation
at91_plla_enable
Remove the extra '#' character that is not used for the 'ldr'
instruction when doing an indirect load of a constant.
Fixes: 4fd36e458392 ("ARM: at91: pm: add plla disable/enable support for sam9x60")
Tested-by: Claudiu Beznea <[email protected]>
Reviewed-by: Claudiu Beznea <[email protected]>
Reviewed-by: Nathan Chancellor <[email protected]>
Acked-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]'
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
cpu_do_idle() is already the default action for arm_pm_idle, there is no
need to open code it.
Signed-off-by: Alexandre Belloni <[email protected]>
Reviewed-by: Claudiu Beznea <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Put node after it has been used.
Fixes: 13f16017d3e3f ("ARM: at91: pm: Tie the USB clock mask to the pmc")
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Not all SoCs supports all the PM mode. User may end up settings,
e.g. backup mode, on a non SAMA5D2 device, but the mode to not be valid.
If backup mode is used on a devices not supporting it there will be no
way of resuming other than rebooting.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
ULP0 fast improves suspend/resume time with few milliseconds the drawback
being the power consumption. The mean values measured for suspend/resume
time are as follows (measured on SAMA5D2 Xplained board), ULP0 compared
with fast ULP0:
- ulp0 fast: suspend time: 169 ms, resume time: 216 ms
- ulp0 : suspend time: 197 ms, resume time: 258 ms
Current consumption while suspended (measured on SAMA5D2 Xplained board):
- ulp0 fast: 730uA
- ulp0 : 270uA
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
if of_find_device_by_node() succeed, at91_pm_sram_init() doesn't have
a corresponding put_device(). Thus add a jump target to fix the exception
handling for this function implementation.
Fixes: d2e467905596 ("ARM: at91: pm: use the mmio-sram pool to access SRAM")
Signed-off-by: yu kuai <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Pull ARM SoC updates from Arnd Bergmann:
"The code changes are mostly for 32-bit platforms and include:
- Lots of updates for the Nvidia Tegra platform, including cpuidle,
pmc, and dt-binding changes
- Microchip at91 power management updates for the recently added
sam9x60 SoC
- Treewide setup_irq deprecation by afzal mohammed
- STMicroelectronics stm32 gains earlycon support
- Renesas platforms with Cortex-A9 can now use the global timer
- Some TI OMAP2+ platforms gain cpuidle support
- Various cleanups for the i.MX6 and Orion platforms, as well as
Kconfig files across all platforms"
* tag 'arm-soc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (75 commits)
ARM: qcom: Add support for IPQ40xx
ARM: mmp: replace setup_irq() by request_irq()
ARM: cns3xxx: replace setup_irq() by request_irq()
ARM: spear: replace setup_irq() by request_irq()
ARM: ep93xx: Replace setup_irq() by request_irq()
ARM: iop32x: replace setup_irq() by request_irq()
arm: mach-dove: Mark dove_io_desc as __maybe_unused
ARM: orion: replace setup_irq() by request_irq()
ARM: debug: stm32: add UART early console support for STM32MP1
ARM: debug: stm32: add UART early console support for STM32H7
ARM: debug: stm32: add UART early console configuration for STM32F7
ARM: debug: stm32: add UART early console configuration for STM32F4
cpuidle: tegra: Disable CC6 state if LP2 unavailable
cpuidle: tegra: Squash Tegra114 driver into the common driver
cpuidle: tegra: Squash Tegra30 driver into the common driver
cpuidle: Refactor and move out NVIDIA Tegra20 driver into drivers/cpuidle
ARM: tegra: cpuidle: Remove unnecessary memory barrier
ARM: tegra: cpuidle: Make abort_flag atomic
ARM: tegra: cpuidle: Handle case where secondary CPU hangs on entering LP2
ARM: tegra: Make outer_disable() open-coded
...
|
|
Add SPDX License Identifier to all .gitignore files.
Signed-off-by: Masahiro Yamada <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
On SAM9X60 2 nop operations has to be introduced after setting
WAITMODE bit in CKGR_MOR.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add PLLA enable/disable support for SAM9X60.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
s/sfr/sfrbu in pm_suspend.S.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This will be used to differentiate b/w different PLLs settings to be
applied in the final/first steps of the suspend/resume process by doing
PLL specific configurations.
Signed-off-by: Claudiu Beznea <[email protected]>
Acked-by: Stephen Boyd <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add macros for PLLA disable and enable (in disable macro the PLLA
state will also be saved). This prepares the field for PLLA disable/enable
for suspend/resume on SAM9X60.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This reverts commit 2725d70aa5138284ba2cebf0ef51dd23e0c9ea21
("ARM: at91: pm: do not disable/enable PLLA for ULP modes").
This is because PLLA is the clock source for CPU, PLLA should
be disabled/enabled in the final/first phase of suspend/resume
so that the power consumption in suspend/resume to be minimal
and suspend/resume time to be minimized.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
SAM9X60's PMC has different master clock register offset than the other
SoCs' PMC. Due to this, specify master clock register offset based
on PMC compatible and pass it to pm_suspend.S since it is also needed
in there. When PM part for SAM9X60 was published the SAM9X60's PMC
(commit f6deae46039c ("clk: at91: add sam9x60 pmc driver")) wasn't
integrated.
Fixes: 01c7031cfa73 ("ARM: at91: pm: initial PM support for SAM9X60")
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Support for AT91/Microchip SoCs depends on ARCH_MULTIPLATFORM or
ARM_SINGLE_ARMV7M, which both select COMMON_CLK.
Hence there is no need for COMMON_CLK_AT91 to select COMMON_CLK.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Cc: Nicolas Ferre <[email protected]>
Cc: Alexandre Belloni <[email protected]>
Cc: Ludovic Desroches <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
Use of_device_id array to find the proper shdwc compatibile node.
SAM9X60's shdwc changes were not integrated when
commit eaedc0d379da ("ARM: at91: pm: add ULP1 support for SAM9X60")
was integrated.
Fixes: eaedc0d379da ("ARM: at91: pm: add ULP1 support for SAM9X60")
Signed-off-by: Claudiu Beznea <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
SAM9X60 PMC's has a different PMC. It was not integrated at the moment
commit 01c7031cfa73 ("ARM: at91: pm: initial PM support for SAM9X60")
was published.
Fixes: 01c7031cfa73 ("ARM: at91: pm: initial PM support for SAM9X60")
Signed-off-by: Claudiu Beznea <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
Move SAM9X60's PM part under SoC config flag. This allows the building
of SAM9X60 platform withouth depending on CONFIG_SOC_AT91SAM9 flag,
allowing us to select only necessary config flags for SAM9X60.
Signed-off-by: Claudiu Beznea <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
Add config flag for SAM9X60 SoC.
Signed-off-by: Claudiu Beznea <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
Add SAM9X60's pll config flag. It was first used in
commit a436c2a447e5 ("clk: at91: add sam9x60 PLL driver").
Signed-off-by: Claudiu Beznea <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
<generated/at91_pm_data-offsets.h> is only generated and included by
arch/arm/mach-at91/, so it does not need to reside in the globally
visible include/generated/.
I renamed it to arch/arm/mach-at91/pm_data-offsets.h since the prefix
'at91_' is just redundant in mach-at91/.
My main motivation of this change is to avoid the race condition for
the parallel build (-j) when CONFIG_IKHEADERS is enabled.
When it is enabled, all the headers under include/ are archived into
kernel/kheaders_data.tar.xz and exposed in the sysfs.
In the parallel build, we have no idea in which order files are built.
- If at91_pm_data-offsets.h is built before kheaders_data.tar.xz,
the header will be included in the archive. Probably nobody will
use it, but it is harmless except that it will increase the archive
size needlessly.
- If kheaders_data.tar.xz is built before at91_pm_data-offsets.h,
the header will not be included in the archive. However, in the next
build, the archive will be re-generated to include the newly-found
at91_pm_data-offsets.h. This is not nice from the build system point
of view.
- If at91_pm_data-offsets.h and kheaders_data.tar.xz are built at the
same time, the corrupted header might be included in the archive,
which does not look nice either.
This commit fixes the race.
Signed-off-by: Masahiro Yamada <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus
Walleij-- the SoC doesn't have active maintainers with hardware,
and in discussions with the vendor the agreement was that it's OK
to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
ARM: stm32: use "depends on" instead of "if" after prompt
ARM: sa1100: convert to common clock framework
ARM: exynos: Cleanup cppcheck shifting warning
ARM: pxa/lubbock: remove lubbock_set_misc_wr() from global view
ARM: exynos: Only build MCPM support if used
arm: add missing include platform-data/atmel.h
ARM: davinci: Use GPIO lookup table for DA850 LEDs
ARM: OMAP2: drop explicit assembler architecture
ARM: use arch_extension directive instead of arch argument
ARM: imx: Switch imx7d to imx-cpufreq-dt for speed-grading
ARM: bcm: Enable PINCTRL for ARCH_BRCMSTB
ARM: bcm: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB
ARM: riscpc: enable chained scatterlist support
ARM: riscpc: reduce IRQ handling code
ARM: riscpc: move RiscPC assembly files from arch/arm/lib to mach-rpc
ARM: riscpc: parse video information from tagged list
ARM: riscpc: add ecard quirk for Atomwide 3port serial card
MAINTAINERS: mvebu: Add git entry
soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in self-refresh
ARM: OMAP2+: Make some variables static
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/soc
AT91 SoC for 5.3
- fix a pm.c warning with W=1
* tag 'at91-5.3-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
arm: add missing include platform-data/atmel.h
Signed-off-by: Olof Johansson <[email protected]>
|
|
Include corresponding headerfile <linux/platform-data/atmel.h> for
function at91_suspend_entering_slow_clock().
../arch/arm/mach-at91/pm.c:279:5: warning: no previous prototype for ‘at91_suspend_entering_slow_clock’ [-Wmissing-prototypes]
int at91_suspend_entering_slow_clock(void)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Philippe Mazenauer <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Enrico Weigelt <[email protected]>
Reviewed-by: Kate Stewart <[email protected]>
Reviewed-by: Allison Randal <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Allison Randal <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Based on 1 normalized pattern(s):
licensed under gplv2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 118 file(s).
Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Jilayne Lovejoy <[email protected]>
Reviewed-by: Steve Winslow <[email protected]>
Reviewed-by: Allison Randal <[email protected]>
Reviewed-by: Kate Stewart <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull clocksource updates from Ingo Molnar:
"Misc clocksource/clockevent driver updates that came in a bit late but
are ready for v5.2"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
misc: atmel_tclib: Do not probe already used TCBs
clocksource/drivers/timer-atmel-tcb: Convert tc_clksrc_suspend|resume() to static
clocksource/drivers/tcb_clksrc: Rename the file for consistency
clocksource/drivers/timer-atmel-pit: Rework Kconfig option
clocksource/drivers/tcb_clksrc: Move Kconfig option
ARM: at91: Implement clocksource selection
clocksource/drivers/tcb_clksrc: Use tcb as sched_clock
clocksource/drivers/tcb_clksrc: Stop depending on atmel_tclib
ARM: at91: move SoC specific definitions to SoC folder
clocksource/drivers/timer-milbeaut: Cleanup common register accesses
clocksource/drivers/timer-milbeaut: Add shutdown function
clocksource/drivers/timer-milbeaut: Fix to enable one-shot timer
clocksource/drivers/tegra: Rework for compensation of suspend time
clocksource/drivers/sp804: Add COMPILE_TEST to CONFIG_ARM_TIMER_SP804
clocksource/drivers/sun4i: Add a compatible for suniv
dt-bindings: timer: Add Allwinner suniv timer
|