| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There is no agreed-upon definition of spin_unlock_wait()'s semantics,
and it appears that all callers could do just as well with a lock/unlock
pair. This commit therefore removes the underlying arch-specific
arch_spin_unlock_wait() for all architectures providing them.
Signed-off-by: Paul E. McKenney <[email protected]>
Cc: <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Alan Stern <[email protected]>
Cc: Andrea Parri <[email protected]>
Cc: Linus Torvalds <[email protected]>
Acked-by: Will Deacon <[email protected]>
Acked-by: Boqun Feng <[email protected]>
|
|
Signed-off-by: Ingo Molnar <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "Updates to for omap debug_ll code to use generic DEBUG_UART_8250 code" from Tony Lindgren:
The legacy code to try to detect the debug_ll uart based on machine
is no longer needed, and we can remove it. Note that the Kconfig
options stay the same, we just need to define the port configuration
now.
* tag 'omap-for-v4.14/debug-ll-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: debug: Use generic 8250 debug_ll for am3517 and am335x
ARM: debug: Use generic 8250 debug_ll for ti81xx
ARM: debug: Use generic 8250 debug_ll for omap3/4/5
ARM: debug: Use generic 8250 debug_ll for omap2 and omap3/4/5 common uarts
|
|
Robert Jarzmik reports that his PXA25x system fails to boot with 4.12,
failing at __flush_whole_cache in arch/arm/mm/proc-xscale.S:215:
0xc0019e20 <+0>: ldr r1, [pc, #788]
0xc0019e24 <+4>: ldr r0, [r1] <== here
with r1 containing 0xc06f82cd, which is the address of "clean_addr".
Examination of the System.map shows:
c06f22c8 D user_pmd_table
c06f22cc d __warned.19178
c06f22cd d clean_addr
indicating that a .data.unlikely section has appeared just before the
.data section from proc-xscale.S. According to objdump -h, it appears
that our assembly files default their .data alignment to 2**0, which
is bad news if the preceding .data section size is not power-of-2
aligned at link time.
Add the appropriate .align directives to all assembly files in arch/arm
that are missing them where we require an appropriate alignment.
Reported-by: Robert Jarzmik <[email protected]>
Tested-by: Robert Jarzmik <[email protected]>
Signed-off-by: Russell King <[email protected]>
|
|
Nadav reported parallel MADV_DONTNEED on same range has a stale TLB
problem and Mel fixed it[1] and found same problem on MADV_FREE[2].
Quote from Mel Gorman:
"The race in question is CPU 0 running madv_free and updating some PTEs
while CPU 1 is also running madv_free and looking at the same PTEs.
CPU 1 may have writable TLB entries for a page but fail the pte_dirty
check (because CPU 0 has updated it already) and potentially fail to
flush.
Hence, when madv_free on CPU 1 returns, there are still potentially
writable TLB entries and the underlying PTE is still present so that a
subsequent write does not necessarily propagate the dirty bit to the
underlying PTE any more. Reclaim at some unknown time at the future
may then see that the PTE is still clean and discard the page even
though a write has happened in the meantime. I think this is possible
but I could have missed some protection in madv_free that prevents it
happening."
This patch aims for solving both problems all at once and is ready for
other problem with KSM, MADV_FREE and soft-dirty story[3].
TLB batch API(tlb_[gather|finish]_mmu] uses [inc|dec]_tlb_flush_pending
and mmu_tlb_flush_pending so that when tlb_finish_mmu is called, we can
catch there are parallel threads going on. In that case, forcefully,
flush TLB to prevent for user to access memory via stale TLB entry
although it fail to gather page table entry.
I confirmed this patch works with [4] test program Nadav gave so this
patch supersedes "mm: Always flush VMA ranges affected by zap_page_range
v2" in current mmotm.
NOTE:
This patch modifies arch-specific TLB gathering interface(x86, ia64,
s390, sh, um). It seems most of architecture are straightforward but
s390 need to be careful because tlb_flush_mmu works only if
mm->context.flush_mm is set to non-zero which happens only a pte entry
really is cleared by ptep_get_and_clear and friends. However, this
problem never changes the pte entries but need to flush to prevent
memory access from stale tlb.
[1] http://lkml.kernel.org/r/[email protected]
[2] http://lkml.kernel.org/r/[email protected]
[3] http://lkml.kernel.org/r/[email protected]
[4] https://patchwork.kernel.org/patch/9861621/
[[email protected]: decrease tlb flush pending count in tlb_finish_mmu]
Link: http://lkml.kernel.org/r/20170808080821.GA31730@bbox
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Minchan Kim <[email protected]>
Signed-off-by: Nadav Amit <[email protected]>
Reported-by: Nadav Amit <[email protected]>
Reported-by: Mel Gorman <[email protected]>
Acked-by: Mel Gorman <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Russell King <[email protected]>
Cc: Tony Luck <[email protected]>
Cc: Martin Schwidefsky <[email protected]>
Cc: "David S. Miller" <[email protected]>
Cc: Heiko Carstens <[email protected]>
Cc: Yoshinori Sato <[email protected]>
Cc: Jeff Dike <[email protected]>
Cc: Andrea Arcangeli <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: Hugh Dickins <[email protected]>
Cc: Mel Gorman <[email protected]>
Cc: Nadav Amit <[email protected]>
Cc: Rik van Riel <[email protected]>
Cc: Sergey Senozhatsky <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
This patch is a preparatory patch for solving race problems caused by
TLB batch. For that, we will increase/decrease TLB flush pending count
of mm_struct whenever tlb_[gather|finish]_mmu is called.
Before making it simple, this patch separates architecture specific part
and rename it to arch_tlb_[gather|finish]_mmu and generic part just
calls it.
It shouldn't change any behavior.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Minchan Kim <[email protected]>
Signed-off-by: Nadav Amit <[email protected]>
Acked-by: Mel Gorman <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Russell King <[email protected]>
Cc: Tony Luck <[email protected]>
Cc: Martin Schwidefsky <[email protected]>
Cc: "David S. Miller" <[email protected]>
Cc: Heiko Carstens <[email protected]>
Cc: Yoshinori Sato <[email protected]>
Cc: Jeff Dike <[email protected]>
Cc: Andrea Arcangeli <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: Hugh Dickins <[email protected]>
Cc: Mel Gorman <[email protected]>
Cc: Nadav Amit <[email protected]>
Cc: Rik van Riel <[email protected]>
Cc: Sergey Senozhatsky <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Generate irqentry and softirqentry text sections without
any Kconfig dependencies. This will add extra sections, but
there should be no performace impact.
Suggested-by: Ingo Molnar <[email protected]>
Signed-off-by: Masami Hiramatsu <[email protected]>
Cc: Ananth N Mavinakayanahalli <[email protected]>
Cc: Anil S Keshavamurthy <[email protected]>
Cc: Chris Zankel <[email protected]>
Cc: David S . Miller <[email protected]>
Cc: Francis Deslauriers <[email protected]>
Cc: Jesper Nilsson <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Max Filippov <[email protected]>
Cc: Mikael Starvik <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Yoshinori Sato <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Link: http://lkml.kernel.org/r/150172789110.27216.3955739126693102122.stgit@devbox
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Add missing errno include to make the header self-contained and avoid
compilation breakage when compiling shared code without
CONFIG_HAVE_ARM_SCU.
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: Russell King <[email protected]>
|
|
Add missing types.h include to make the suspend header self-contained
and avoid compilation breakage due to include-directive ordering.
Acked-by: Pavel Machek <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: Russell King <[email protected]>
|
|
Pull ARM fixes from Russell King:
"Two areas addressed by these fixes:
- Fixes from Dave Martin for the signal frames that were broken with
certain configurations. No one noticed until recently.
- More kexec fixes to ensure that the crashkernel region is correctly
allocated, and a fix for the location of the device tree when
several kexec kernels are loaded"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8687/1: signal: Fix unparseable iwmmxt_sigframe in uc_regspace[]
ARM: 8686/1: iwmmxt: Add missing __user annotations to sigframe accessors
ARM: kexec: fix failure to boot crash kernel
ARM: kexec: avoid allocating crashkernel region outside lowmem
|
|
In kernels with CONFIG_IWMMXT=y running on non-iWMMXt hardware, the
signal frame can be left partially uninitialised in such a way
that userspace cannot parse uc_regspace[] safely. In particular,
this means that the VFP registers cannot be located reliably in the
signal frame when a multi_v7_defconfig kernel is run on the
majority of platforms.
The cause is that the uc_regspace[] is laid out statically based on
the kernel config, but the decision of whether to save/restore the
iWMMXt registers must be a runtime decision.
To minimise breakage of software that may assume a fixed layout,
this patch emits a dummy block of the same size as iwmmxt_sigframe,
for non-iWMMXt threads. However, the magic and size of this block
are now filled in to help parsers skip over it. A new DUMMY_MAGIC
is defined for this purpose.
It is probably legitimate (if non-portable) for userspace to
manufacture its own sigframe for sigreturn, and there is no obvious
reason why userspace should be required to insert a DUMMY_MAGIC
block when running on non-iWMMXt hardware, when omitting it has
worked just fine forever in other configurations. So in this case,
sigreturn does not require this block to be present.
Reported-by: Edmund Grimley-Evans <[email protected]>
Signed-off-by: Dave Martin <[email protected]>
Signed-off-by: Russell King <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core fixes from Ingo Molnar:
"A fix to WARN_ON_ONCE() done by modules, plus a MAINTAINERS update"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
debug: Fix WARN_ON_ONCE() for modules
MAINTAINERS: Update the PTRACE entry
|
|
When kexec was converted to DTB, the dtb address was passed between
machine_kexec_prepare() and machine_kexec() using a static variable.
This is bad news if you load a crash kernel followed by a normal
kernel or vice versa - the last loaded kernel overwrites the dtb
address.
This can result in kexec failures, as (eg) we try to boot the crash
kernel with the last loaded dtb. For example, with:
the crash kernel fails to find the dtb.
Avoid this by defining a kimage architecture structure, and store
the address to be passed in r2 there, which will either be the ATAGs
or the dtb blob.
Fixes: 4cabd1d9625c ("ARM: 7539/1: kexec: scan for dtb magic in segments")
Fixes: 42d720d1731a ("ARM: kexec: Make .text R/W in machine_kexec")
Reported-by: Keerthy <[email protected]>
Tested-by: Keerthy <[email protected]>
Signed-off-by: Russell King <[email protected]>
|
|
Mike Galbraith reported a situation where a WARN_ON_ONCE() call in DRM
code turned into an oops. As it turns out, WARN_ON_ONCE() seems to be
completely broken when called from a module.
The bug was introduced with the following commit:
19d436268dde ("debug: Add _ONCE() logic to report_bug()")
That commit changed WARN_ON_ONCE() to move its 'once' logic into the bug
trap handler. It requires a writable bug table so that the BUGFLAG_DONE
bit can be written to the flags to indicate the first warning has
occurred.
The bug table was made writable for vmlinux, which relies on
vmlinux.lds.S and vmlinux.lds.h for laying out the sections. However,
it wasn't made writable for modules, which rely on the ELF section
header flags.
Reported-by: Mike Galbraith <[email protected]>
Tested-by: Masami Hiramatsu <[email protected]>
Signed-off-by: Josh Poimboeuf <[email protected]>
Acked-by: Peter Zijlstra (Intel) <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Fixes: 19d436268dde ("debug: Add _ONCE() logic to report_bug()")
Link: http://lkml.kernel.org/r/a53b04235a65478dd9afc51f5b329fdc65c84364.1500095401.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull structure randomization updates from Kees Cook:
"Now that IPC and other changes have landed, enable manual markings for
randstruct plugin, including the task_struct.
This is the rest of what was staged in -next for the gcc-plugins, and
comes in three patches, largest first:
- mark "easy" structs with __randomize_layout
- mark task_struct with an optional anonymous struct to isolate the
__randomize_layout section
- mark structs to opt _out_ of automated marking (which will come
later)
And, FWIW, this continues to pass allmodconfig (normal and patched to
enable gcc-plugins) builds of x86_64, i386, arm64, arm, powerpc, and
s390 for me"
* tag 'gcc-plugins-v4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
randstruct: opt-out externally exposed function pointer structs
task_struct: Allow randomized layout
randstruct: Mark various structs for randomization
|
|
We want to use generic 8250 debug_ll code to get DEBUG_UNCOMPRESS
working and to simplify the code. The old debug_ll code is no longer
needed and the machine ID based detection is no longer used.
Note that for most part there's no need to keep DEBUG_LL enabled.
We now have CONFIG_SERIAL_EARLYCON working very early as long as
the kernel cmdline has "earlycon" in it and the board specific dts
file has chosen configured with with the port using stdout-path.
Cc: Hoeun Ryu <[email protected]>
Cc: Russell King <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
We want to use generic 8250 debug_ll code to get DEBUG_UNCOMPRESS
working and to simplify the code. The old debug_ll code is no longer
needed and the machine ID based detection is no longer used.
Note that for most part there's no need to keep DEBUG_LL enabled.
We now have CONFIG_SERIAL_EARLYCON working very early as long as
the kernel cmdline has "earlycon" in it and the board specific dts
file has chosen configured with with the port using stdout-path.
Cc: Hoeun Ryu <[email protected]>
Cc: Russell King <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
We want to use generic 8250 debug_ll code to get DEBUG_UNCOMPRESS
working and to simplify the code. The old debug_ll code is no longer
needed and the machine ID based detection is no longer used.
Note that for most part there's no need to keep DEBUG_LL enabled.
We now have CONFIG_SERIAL_EARLYCON working very early as long as
the kernel cmdline has "earlycon" in it and the board specific dts
file has chosen configured with with the port using stdout-path.
Cc: Hoeun Ryu <[email protected]>
Cc: Russell King <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
We want to use generic 8250 debug_ll code to get DEBUG_UNCOMPRESS
working and to simplify the code. The old debug_ll code is no longer
needed and the machine ID based detection is no longer used.
Note that for most part there's no need to keep DEBUG_LL enabled.
We now have CONFIG_SERIAL_EARLYCON working very early as long as
the kernel cmdline has "earlycon" in it and the board specific dts
file has chosen configured with with the port using stdout-path.
Cc: Hoeun Ryu <[email protected]>
Cc: Russell King <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull uacess-unaligned removal from Al Viro:
"That stuff had just one user, and an exotic one, at that - binfmt_flat
on arm and m68k"
* 'work.uaccess-unaligned' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
kill {__,}{get,put}_user_unaligned()
binfmt_flat: flat_{get,put}_addr_from_rp() should be able to fail
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- Move generic-y of exported headers to uapi/asm/Kbuild for complete
de-coupling of UAPI
- Clean up scripts/Makefile.headersinst
- Fix host programs for 32 bit machine with XFS file system
* tag 'kbuild-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (29 commits)
kbuild: Enable Large File Support for hostprogs
kbuild: remove wrapper files handling from Makefile.headersinst
kbuild: split exported generic header creation into uapi-asm-generic
kbuild: do not include old-kbuild-file from Makefile.headersinst
xtensa: move generic-y of exported headers to uapi/asm/Kbuild
unicore32: move generic-y of exported headers to uapi/asm/Kbuild
tile: move generic-y of exported headers to uapi/asm/Kbuild
sparc: move generic-y of exported headers to uapi/asm/Kbuild
sh: move generic-y of exported headers to uapi/asm/Kbuild
parisc: move generic-y of exported headers to uapi/asm/Kbuild
openrisc: move generic-y of exported headers to uapi/asm/Kbuild
nios2: move generic-y of exported headers to uapi/asm/Kbuild
nios2: remove unneeded arch/nios2/include/(generated/)asm/signal.h
microblaze: move generic-y of exported headers to uapi/asm/Kbuild
metag: move generic-y of exported headers to uapi/asm/Kbuild
m68k: move generic-y of exported headers to uapi/asm/Kbuild
m32r: move generic-y of exported headers to uapi/asm/Kbuild
ia64: remove redundant generic-y += kvm_para.h from asm/Kbuild
hexagon: move generic-y of exported headers to uapi/asm/Kbuild
h8300: move generic-y of exported headers to uapi/asm/Kbuild
...
|
|
asmlinkage is either 'extern "C"' or blank.
Move the uses of asmlinkage before the return types to be similar
to the rest of the kernel.
Link: http://lkml.kernel.org/r/005b8e120650c6a13b541e420f4e3605603fe9e6.1499284835.git.joe@perches.com
Signed-off-by: Joe Perches <[email protected]>
Cc: Christoffer Dall <[email protected]>
Cc: Marc Zyngier <[email protected]>
Cc: Paolo Bonzini <[email protected]>
Cc: Radim Krcmar <[email protected]>
Cc: Russell King <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Now that explicitly executed loaders are loaded in the mmap region, we
have more freedom to decide where we position PIE binaries in the
address space to avoid possible collisions with mmap or stack regions.
4MB is chosen here mainly to have parity with x86, where this is the
traditional minimum load location, likely to avoid historically
requiring a 4MB page table entry when only a portion of the first 4MB
would be used (since the NULL address is avoided).
For ARM the position could be 0x8000, the standard ET_EXEC load address,
but that is needlessly close to the NULL address, and anyone running PIE
on 32-bit ARM will have an MMU, so the tight mapping is not needed.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Kees Cook <[email protected]>
Cc: Russell King <[email protected]>
Cc: Catalin Marinas <[email protected]>
Cc: Will Deacon <[email protected]>
Cc: Benjamin Herrenschmidt <[email protected]>
Cc: Paul Mackerras <[email protected]>
Cc: Michael Ellerman <[email protected]>
Cc: Martin Schwidefsky <[email protected]>
Cc: Heiko Carstens <[email protected]>
Cc: James Hogan <[email protected]>
Cc: Pratyush Anand <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: "H. Peter Anvin" <[email protected]>
Cc: Alexander Viro <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: Daniel Micay <[email protected]>
Cc: Dmitry Safonov <[email protected]>
Cc: Grzegorz Andrejczuk <[email protected]>
Cc: Kees Cook <[email protected]>
Cc: Masahiro Yamada <[email protected]>
Cc: Qualys Security Advisory <[email protected]>
Cc: Rik van Riel <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Since commit fcc8487d477a ("uapi: export all headers under uapi
directories"), all (and only) headers under uapi directories are
exported, but asm-generic wrappers are still exceptions.
To complete de-coupling the uapi from kernel headers, move generic-y
of exported headers to uapi/asm/Kbuild.
With this change, "make headers_install" will just need to parse
uapi/asm/Kbuild to build up exported headers.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add sysfs max_link_speed/width, current_link_speed/width (Wong Vee
Khee)
- make host bridge IRQ mapping much more generic (Matthew Minter,
Lorenzo Pieralisi)
- convert most drivers to pci_scan_root_bus_bridge() (Lorenzo
Pieralisi)
- mutex sriov_configure() (Jakub Kicinski)
- mutex pci_error_handlers callbacks (Christoph Hellwig)
- split ->reset_notify() into ->reset_prepare()/reset_done()
(Christoph Hellwig)
- support multiple PCIe portdrv interrupts for MSI as well as MSI-X
(Gabriele Paoloni)
- allocate MSI/MSI-X vector for Downstream Port Containment (Gabriele
Paoloni)
- fix MSI IRQ affinity pre/post/min_vecs issue (Michael Hernandez)
- test INTx masking during enumeration, not at run-time (Piotr Gregor)
- avoid using device_may_wakeup() for runtime PM (Rafael J. Wysocki)
- restore the status of PCI devices across hibernation (Chen Yu)
- keep parent resources that start at 0x0 (Ard Biesheuvel)
- enable ECRC only if device supports it (Bjorn Helgaas)
- restore PRI and PASID state after Function-Level Reset (CQ Tang)
- skip DPC event if device is not present (Keith Busch)
- check domain when matching SMBIOS info (Sujith Pandel)
- mark Intel XXV710 NIC INTx masking as broken (Alex Williamson)
- avoid AMD SB7xx EHCI USB wakeup defect (Kai-Heng Feng)
- work around long-standing Macbook Pro poweroff issue (Bjorn Helgaas)
- add Switchtec "running" status flag (Logan Gunthorpe)
- fix dra7xx incorrect RW1C IRQ register usage (Arvind Yadav)
- modify xilinx-nwl IRQ chip for legacy interrupts (Bharat Kumar
Gogada)
- move VMD SRCU cleanup after bus, child device removal (Jon Derrick)
- add Faraday clock handling (Linus Walleij)
- configure Rockchip MPS and reorganize (Shawn Lin)
- limit Qualcomm TLP size to 2K (hardware issue) (Srinivas Kandagatla)
- support Tegra MSI 64-bit addressing (Thierry Reding)
- use Rockchip normal (not privileged) register bank (Shawn Lin)
- add HiSilicon Kirin SoC PCIe controller driver (Xiaowei Song)
- add Sigma Designs Tango SMP8759 PCIe controller driver (Marc
Gonzalez)
- add MediaTek PCIe host controller support (Ryder Lee)
- add Qualcomm IPQ4019 support (John Crispin)
- add HyperV vPCI protocol v1.2 support (Jork Loeser)
- add i.MX6 regulator support (Quentin Schulz)
* tag 'pci-v4.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (113 commits)
PCI: tango: Add Sigma Designs Tango SMP8759 PCIe host bridge support
PCI: Add DT binding for Sigma Designs Tango PCIe controller
PCI: rockchip: Use normal register bank for config accessors
dt-bindings: PCI: Add documentation for MediaTek PCIe
PCI: Remove __pci_dev_reset() and pci_dev_reset()
PCI: Split ->reset_notify() method into ->reset_prepare() and ->reset_done()
PCI: xilinx: Make of_device_ids const
PCI: xilinx-nwl: Modify IRQ chip for legacy interrupts
PCI: vmd: Move SRCU cleanup after bus, child device removal
PCI: vmd: Correct comment: VMD domains start at 0x10000, not 0x1000
PCI: versatile: Add local struct device pointers
PCI: tegra: Do not allocate MSI target memory
PCI: tegra: Support MSI 64-bit addressing
PCI: rockchip: Use local struct device pointer consistently
PCI: rockchip: Check for clk_prepare_enable() errors during resume
MAINTAINERS: Remove Wenrui Li as Rockchip PCIe driver maintainer
PCI: rockchip: Configure RC's MPS setting
PCI: rockchip: Reconfigure configuration space header type
PCI: rockchip: Split out rockchip_pcie_cfg_configuration_accesses()
PCI: rockchip: Move configuration accesses into rockchip_pcie_cfg_atu()
...
|
|
Pull ARM updates from Russell King:
- add support for ftrace-with-registers, which is needed for kgraft and
other ftrace tools
- support for mremap() for the sigpage/vDSO so that checkpoint/restore
can work
- add timestamps to each line of the register dump output
- remove the unused KTHREAD_SIZE from nommu
- align the ARM bitops APIs with the generic API (using unsigned long
pointers rather than void pointers)
- make the configuration of userspace Thumb support an expert option so
that we can default it on, and avoid some hard to debug userspace
crashes
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8684/1: NOMMU: Remove unused KTHREAD_SIZE definition
ARM: 8683/1: ARM32: Support mremap() for sigpage/vDSO
ARM: 8679/1: bitops: Align prototypes to generic API
ARM: 8678/1: ftrace: Adds support for CONFIG_DYNAMIC_FTRACE_WITH_REGS
ARM: make configuration of userspace Thumb support an expert option
ARM: 8673/1: Fix __show_regs output timestamps
|
|
Ensure the address limit is a user-mode segment before returning to
user-mode. Otherwise a process can corrupt kernel-mode memory and
elevate privileges [1].
The set_fs function sets the TIF_SETFS flag to force a slow path on
return. In the slow path, the address limit is checked to be USER_DS if
needed.
The TIF_SETFS flag is added to _TIF_WORK_MASK shifting _TIF_SYSCALL_WORK
for arm instruction immediate support. The global work mask is too big
to used on a single instruction so adapt ret_fast_syscall.
[1] https://bugs.chromium.org/p/project-zero/issues/detail?id=990
Signed-off-by: Thomas Garnier <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Mark Rutland <[email protected]>
Cc: [email protected]
Cc: Catalin Marinas <[email protected]>
Cc: Will Deacon <[email protected]>
Cc: David Howells <[email protected]>
Cc: Dave Hansen <[email protected]>
Cc: Miroslav Benes <[email protected]>
Cc: Chris Metcalf <[email protected]>
Cc: Pratyush Anand <[email protected]>
Cc: Russell King <[email protected]>
Cc: Petr Mladek <[email protected]>
Cc: Rik van Riel <[email protected]>
Cc: Kees Cook <[email protected]>
Cc: Arnd Bergmann <[email protected]>
Cc: Al Viro <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: Josh Poimboeuf <[email protected]>
Cc: [email protected]
Cc: Will Drewry <[email protected]>
Cc: [email protected]
Cc: Oleg Nesterov <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: Paolo Bonzini <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Clean up Makefiles and scripts
- Improve clang support
- Remove unneeded genhdr-y syntax
- Remove unneeded cc-option-align macro
- Introduce __cc-option macro and use it to fix x86 boot code compiler
flags
* tag 'kbuild-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: improve comments on KBUILD_SRC
x86/build: Specify stack alignment for clang
x86/build: Use __cc-option for boot code compiler options
kbuild: Add __cc-option macro
kbuild: remove cc-option-align
kbuild: replace genhdr-y with generated-y
kbuild: clang: Disable 'address-of-packed-member' warning
kbuild: remove duplicated arch/*/include/generated/uapi include path
kbuild: speed up checksyscalls.sh
kbuild: simplify silent build (-s) detection
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull user access str* updates from Al Viro:
"uaccess str...() dead code removal"
* 'uaccess.strlen' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
s390 keyboard.c: don't open-code strndup_user()
mips: get rid of unused __strnlen_user()
get rid of unused __strncpy_from_user() instances
kill strlen_user()
|
|
Pull dma-mapping infrastructure from Christoph Hellwig:
"This is the first pull request for the new dma-mapping subsystem
In this new subsystem we'll try to properly maintain all the generic
code related to dma-mapping, and will further consolidate arch code
into common helpers.
This pull request contains:
- removal of the DMA_ERROR_CODE macro, replacing it with calls to
->mapping_error so that the dma_map_ops instances are more self
contained and can be shared across architectures (me)
- removal of the ->set_dma_mask method, which duplicates the
->dma_capable one in terms of functionality, but requires more
duplicate code.
- various updates for the coherent dma pool and related arm code
(Vladimir)
- various smaller cleanups (me)"
* tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping: (56 commits)
ARM: dma-mapping: Remove traces of NOMMU code
ARM: NOMMU: Set ARM_DMA_MEM_BUFFERABLE for M-class cpus
ARM: NOMMU: Introduce dma operations for noMMU
drivers: dma-mapping: allow dma_common_mmap() for NOMMU
drivers: dma-coherent: Introduce default DMA pool
drivers: dma-coherent: Account dma_pfn_offset when used with device tree
dma: Take into account dma_pfn_offset
dma-mapping: replace dmam_alloc_noncoherent with dmam_alloc_attrs
dma-mapping: remove dmam_free_noncoherent
crypto: qat - avoid an uninitialized variable warning
au1100fb: remove a bogus dma_free_nonconsistent call
MAINTAINERS: add entry for dma mapping helpers
powerpc: merge __dma_set_mask into dma_set_mask
dma-mapping: remove the set_dma_mask method
powerpc/cell: use the dma_supported method for ops switching
powerpc/cell: clean up fixed mapping dma_ops initialization
tile: remove dma_supported and mapping_error methods
xen-swiotlb: remove xen_swiotlb_set_dma_mask
arm: implement ->dma_supported instead of ->set_dma_mask
mips/loongson64: implement ->dma_supported instead of ->set_dma_mask
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"Other than fixes and cleanups it contains:
- support > 32 VCPUs at domain restore
- support for new sysfs nodes related to Xen
- some performance tuning for Linux running as Xen guest"
* tag 'for-linus-4.13-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: allow userspace access during hypercalls
x86: xen: remove unnecessary variable in xen_foreach_remap_area()
xen: allocate page for shared info page from low memory
xen: avoid deadlock in xenbus driver
xen: add sysfs node for hypervisor build id
xen: sync include/xen/interface/version.h
xen: add sysfs node for guest type
doc,xen: document hypervisor sysfs nodes for xen
xen/vcpu: Handle xen_vcpu_setup() failure at boot
xen/vcpu: Handle xen_vcpu_setup() failure in hotplug
xen/pv: Fix OOPS on restore for a PV, !SMP domain
xen/pvh*: Support > 32 VCPUs at domain restore
xen/vcpu: Simplify xen_vcpu related code
xen-evtchn: Bind dyn evtchn:qemu-dm interrupt to next online VCPU
xen: avoid type warning in xchg_xen_ulong
xen: fix HYPERVISOR_dm_op() prototype
xen: don't print error message in case of missing Xenstore entry
arm/xen: Adjust one function call together with a variable assignment
arm/xen: Delete an error message for a failed memory allocation in __set_phys_to_machine_multi()
arm/xen: Improve a size determination in __set_phys_to_machine_multi()
|
|
Pull KVM updates from Paolo Bonzini:
"PPC:
- Better machine check handling for HV KVM
- Ability to support guests with threads=2, 4 or 8 on POWER9
- Fix for a race that could cause delayed recognition of signals
- Fix for a bug where POWER9 guests could sleep with interrupts pending.
ARM:
- VCPU request overhaul
- allow timer and PMU to have their interrupt number selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
s390:
- initial machine check forwarding
- migration support for the CMMA page hinting information
- cleanups and fixes
x86:
- nested VMX bugfixes and improvements
- more reliable NMI window detection on AMD
- APIC timer optimizations
Generic:
- VCPU request overhaul + documentation of common code patterns
- kvm_stat improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (124 commits)
Update my email address
kvm: vmx: allow host to access guest MSR_IA32_BNDCFGS
x86: kvm: mmu: use ept a/d in vmcs02 iff used in vmcs12
kvm: x86: mmu: allow A/D bits to be disabled in an mmu
x86: kvm: mmu: make spte mmio mask more explicit
x86: kvm: mmu: dead code thanks to access tracking
KVM: PPC: Book3S: Fix typo in XICS-on-XIVE state saving code
KVM: PPC: Book3S HV: Close race with testing for signals on guest entry
KVM: PPC: Book3S HV: Simplify dynamic micro-threading code
KVM: x86: remove ignored type attribute
KVM: LAPIC: Fix lapic timer injection delay
KVM: lapic: reorganize restart_apic_timer
KVM: lapic: reorganize start_hv_timer
kvm: nVMX: Check memory operand to INVVPID
KVM: s390: Inject machine check into the nested guest
KVM: s390: Inject machine check into the guest
tools/kvm_stat: add new interactive command 'b'
tools/kvm_stat: add new command line switch '-i'
tools/kvm_stat: fix error on interactive command 'g'
KVM: SVM: suppress unnecessary NMI singlestep on GIF=0 and nested exit
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
- RAS reporting via GHES/APEI (ACPI)
- Indirect ftrace trampolines for modules
- Improvements to kernel fault reporting
- Page poisoning
- Sigframe cleanups and preparation for SVE context
- Core dump fixes
- Sparse fixes (mainly relating to endianness)
- xgene SoC PMU v3 driver
- Misc cleanups and non-critical fixes
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (75 commits)
arm64: fix endianness annotation for 'struct jit_ctx' and friends
arm64: cpuinfo: constify attribute_group structures.
arm64: ptrace: Fix incorrect get_user() use in compat_vfp_set()
arm64: ptrace: Remove redundant overrun check from compat_vfp_set()
arm64: ptrace: Avoid setting compat FP[SC]R to garbage if get_user fails
arm64: fix endianness annotation for __apply_alternatives()/get_alt_insn()
arm64: fix endianness annotation in get_kaslr_seed()
arm64: add missing conversion to __wsum in ip_fast_csum()
arm64: fix endianness annotation in acpi_parking_protocol.c
arm64: use readq() instead of readl() to read 64bit entry_point
arm64: fix endianness annotation for reloc_insn_movw() & reloc_insn_imm()
arm64: fix endianness annotation for aarch64_insn_write()
arm64: fix endianness annotation in aarch64_insn_read()
arm64: fix endianness annotation in call_undef_hook()
arm64: fix endianness annotation for debug-monitors.c
ras: mark stub functions as 'inline'
arm64: pass endianness info to sparse
arm64: ftrace: fix !CONFIG_ARM64_MODULE_PLTS kernels
arm64: signal: Allow expansion of the signal frame
acpi: apei: check for pending errors when probing GHES entries
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull GCC plugin updates from Kees Cook:
"The big part is the randstruct plugin infrastructure.
This is the first of two expected pull requests for randstruct since
there are dependencies in other trees that would be easier to merge
once those have landed. Notably, the IPC allocation refactoring in
-mm, and many trivial merge conflicts across several trees when
applying the __randomize_layout annotation.
As a result, it seemed like I should send this now since it is
relatively self-contained, and once the rest of the trees have landed,
send the annotation patches. I'm expecting the final phase of
randstruct (automatic struct selection) will land for v4.14, but if
its other tree dependencies actually make it for v4.13, I can send
that merge request too.
Summary:
- typo fix in Kconfig (Jean Delvare)
- randstruct infrastructure"
* tag 'gcc-plugins-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
ARM: Prepare for randomized task_struct
randstruct: Whitelist NIU struct page overloading
randstruct: Whitelist big_key path struct overloading
randstruct: Whitelist UNIXCB cast
randstruct: Whitelist struct security_hook_heads cast
gcc-plugins: Add the randstruct plugin
Fix English in description of GCC_PLUGIN_STRUCTLEAK
compiler: Add __designated_init annotation
gcc-plugins: Detail c-common.h location for GCC 4.6
|
|
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"A rather large update for timers/timekeeping:
- compat syscall consolidation (Al Viro)
- Posix timer consolidation (Christoph Helwig / Thomas Gleixner)
- Cleanup of the device tree based initialization for clockevents and
clocksources (Daniel Lezcano)
- Consolidation of the FTTMR010 clocksource/event driver (Linus
Walleij)
- The usual set of small fixes and updates all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (93 commits)
timers: Make the cpu base lock raw
clocksource/drivers/mips-gic-timer: Fix an error code in 'gic_clocksource_of_init()'
clocksource/drivers/fsl_ftm_timer: Unmap region obtained by of_iomap
clocksource/drivers/tcb_clksrc: Make IO endian agnostic
clocksource/drivers/sun4i: Switch to the timer-of common init
clocksource/drivers/timer-of: Fix invalid iomap check
Revert "ktime: Simplify ktime_compare implementation"
clocksource/drivers: Fix uninitialized variable use in timer_of_init
kselftests: timers: Add test for frequency step
kselftests: timers: Fix inconsistency-check to not ignore first timestamp
time: Add warning about imminent deprecation of CONFIG_GENERIC_TIME_VSYSCALL_OLD
time: Clean up CLOCK_MONOTONIC_RAW time handling
posix-cpu-timers: Make timespec to nsec conversion safe
itimer: Make timeval to nsec conversion range limited
timers: Fix parameter description of try_to_del_timer_sync()
ktime: Simplify ktime_compare implementation
clocksource/drivers/fttmr010: Factor out clock read code
clocksource/drivers/fttmr010: Implement delay timer
clocksource/drivers: Add timer-of common init routine
clocksource/drivers/tcb_clksrc: Save timer context on suspend/resume
...
|
|
no users left
Signed-off-by: Al Viro <[email protected]>
|
|
on MMU targets EFAULT is possible here. Make both return 0 or error,
passing what used to be the return value of flat_get_addr_from_rp()
by reference.
Signed-off-by: Al Viro <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI updates from Ingo Molnar:
"The main changes in this cycle were:
- Rework the EFI capsule loader to allow for workarounds for
non-compliant firmware (Ard Biesheuvel)
- Implement a capsule loader quirk for Quark X102x (Jan Kiszka)
- Enable SMBIOS/DMI support for the ARM architecture (Ard Biesheuvel)
- Add CONFIG_EFI_PGT_DUMP=y support for x86-32 and kexec (Sai
Praneeth)
- Fixes for EFI support for Xen dom0 guests running under x86-64
hosts (Daniel Kiper)"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/xen/efi: Initialize only the EFI struct members used by Xen
efi: Process the MEMATTR table only if EFI_MEMMAP is enabled
efi/arm: Enable DMI/SMBIOS
x86/efi: Extend CONFIG_EFI_PGT_DUMP support to x86_32 and kexec as well
efi/efi_test: Use memdup_user() helper
efi/capsule: Add support for Quark security header
efi/capsule-loader: Use page addresses rather than struct page pointers
efi/capsule-loader: Redirect calls to efi_capsule_setup_info() via weak alias
efi/capsule: Remove NULL test on kmap()
efi/capsule-loader: Use a cached copy of the capsule header
efi/capsule: Adjust return type of efi_capsule_setup_info()
efi/capsule: Clean up pr_err/_info() messages
efi/capsule: Remove pr_debug() on ENOMEM or EFAULT
efi/capsule: Fix return code on failing kmap/vmap
|
|
Some function pointer structures are used externally to the kernel, like
the paravirt structures. These should never be randomized, so mark them
as such, in preparation for enabling randstruct's automatic selection
of all-function-pointer structures.
These markings are verbatim from Brad Spengler/PaX Team's code in the
last public patch of grsecurity/PaX based on my understanding of the
code. Changes or omissions from the original code are mine and don't
reflect the original grsecurity/PaX code.
Signed-off-by: Kees Cook <[email protected]>
|
|
With the new task struct randomization, we can run into a build
failure for certain random seeds, which will place fields beyond
the allow immediate size in the assembly:
arch/arm/kernel/entry-armv.S: Assembler messages:
arch/arm/kernel/entry-armv.S:803: Error: bad immediate value for offset (4096)
Only two constants in asm-offset.h are affected, and I'm changing
both of them here to work correctly in all configurations.
One more macro has the problem, but is currently unused, so this
removes it instead of adding complexity.
Suggested-by: Ard Biesheuvel <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
[kees: Adjust commit log slightly]
Signed-off-by: Kees Cook <[email protected]>
|
|
R/M classes of cpus can have memory covered by MPU which in turn might
configure RAM as Normal i.e. bufferable and cacheable. It breaks
dma_alloc_coherent() and friends, since data can stuck in caches now
or be buffered.
This patch factors out DMA support for NOMMU configuration into
separate entity which provides dedicated dma_ops. We have to handle
there several cases:
- configurations with MMU/MPU setup
- configurations without MMU/MPU setup
- special case for M-class, since caches and MPU there are optional
In general we rely on default DMA area for coherent allocations or/and
per-device memory reserves suitable for coherent DMA, so if such
regions are set coherent allocations go from there.
In case MMU/MPU was not setup we fallback to normal page allocator for
DMA memory allocation.
In case we run M-class cpus, for configuration without cache support
(like Cortex-M3/M4) dma operations are forced to be coherent and wired
with dma-noop (such decision is made based on cacheid global
variable); however, if caches are detected there and no DMA coherent
region is given (either default or per-device), dma is disallowed even
MPU is not set - it is because M-class implement system memory map
which defines part of address space as Normal memory.
Reported-by: Alexandre Torgue <[email protected]>
Reported-by: Andras Szemzo <[email protected]>
Tested-by: Benjamin Gaignard <[email protected]>
Tested-by: Andras Szemzo <[email protected]>
Tested-by: Alexandre TORGUE <[email protected]>
Reviewed-by: Robin Murphy <[email protected]>
Signed-off-by: Vladimir Murzin <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Acked-by: Russell King <[email protected]>
[hch: removed the dma_supported() implementation that isn't required anymore]
Signed-off-by: Christoph Hellwig <[email protected]>
|
|
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert ARM bios32 code to pci_scan_root_bus_bridge() to improve the PCI
root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <[email protected]>
[bhelgaas: fold in warning fix from Arnd Bergmann <[email protected]>:
http://lkml.kernel.org/r/[email protected]]
[bhelgaas: set bridge->ops for mv78xx0]
[bhelgaas: fold in fixes from Lorenzo Pieralisi <[email protected]>:
http://lkml.kernel.org/r/20170701135457.GB8977@red-moon]
Signed-off-by: Bjorn Helgaas <[email protected]>
Cc: Jason Cooper <[email protected]>
Cc: Russell King <[email protected]>
Cc: Andrew Lunn <[email protected]>
|
|
And instead wire it up as method for all the dma_map_ops instances.
Note that the code seems a little fishy for dmabounce and iommu, but
for now I'd like to preserve the existing behavior 1:1.
Signed-off-by: Christoph Hellwig <[email protected]>
|
|
DMA_ERROR_CODE is going to go away, so don't rely on it.
Signed-off-by: Christoph Hellwig <[email protected]>
|
|
I didn't find any use of this macro in the current kernel tree (with git
grep). KTHREAD_SIZE is no longer used for a very very long time. So
let's remove this definition.
Signed-off-by: Jérémy Lefaure <[email protected]>
Reviewed-by: Vladimir Murzin <[email protected]>
Signed-off-by: Russell King <[email protected]>
|
|
Currently external aborts are unsupported by the guest abort
handling. Add handling for SEAs so that the host kernel reports
SEAs which occur in the guest kernel.
When an SEA occurs in the guest kernel, the guest exits and is
routed to kvm_handle_guest_abort(). Prior to this patch, a print
message of an unsupported FSC would be printed and nothing else
would happen. With this patch, the code gets routed to the APEI
handling of SEAs in the host kernel to report the SEA information.
Signed-off-by: Tyler Baicar <[email protected]>
Acked-by: Catalin Marinas <[email protected]>
Acked-by: Marc Zyngier <[email protected]>
Acked-by: Christoffer Dall <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
Originally, generated-y and genhdr-y had different meaning, like
follows:
- generated-y: generated headers (other than asm-generic wrappers)
- header-y : headers to be exported
- genhdr-y : generated headers to be exported (generated-y + header-y)
Since commit fcc8487d477a ("uapi: export all headers under uapi
directories"), headers under UAPI directories are all exported.
So, there is no more difference between generated-y and genhdr-y.
We see two users of genhdr-y, arch/{arm,x86}/include/uapi/asm/Kbuild.
They generate some headers in arch/{arm,x86}/include/generated/uapi/asm
directories, which are obviously exported.
Replace them with generated-y, and abolish genhdr-y.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Nicolas Dichtel <[email protected]>
|
|
Pick up dependent changes.
|