| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Northstar SoCs have 3 usable Ethernet interfaces each connected to one
of switch ports. They all use fixed links.
Signed-off-by: Rafał Miłecki <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Florian Fainelli <[email protected]>
|
|
This allows setting FullMAC firmware regulatory domain.
Signed-off-by: Dan Haab <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Florian Fainelli <[email protected]>
|
|
Add missing whitespace between node name/label and opening {.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Florian Fainelli <[email protected]>
|
|
The pwm-bcm2835 supports PWM polarity, so adjust the affected dtsi
files accordingly and fix the dtbs_check warning:
pwm@7e20c000: #pwm-cells:0:0: 3 was expected
Signed-off-by: Stefan Wahren <[email protected]>
Reviewed-by: Uwe Kleine-König <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Florian Fainelli <[email protected]>
|
|
After converting the bcm2835-dma DT binding to YAML, the DT schema
checks gave warnings like:
$nodename:0: 'dma@7e007000' does not match '^dma-controller(@.*)?$'
So fix them accordingly.
Signed-off-by: Stefan Wahren <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Florian Fainelli <[email protected]>
|
|
Currently the dtbs_check for bcm2837 generates warnings like this:
gpio@7e200000: 'pinctrl-0' is a dependency of 'pinctrl-names'
This is caused by the definition of pinctrl-names without matching
pinctrl group and vice versa. So defining both at the same place
make the dts files easier to review.
Signed-off-by: Stefan Wahren <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Florian Fainelli <[email protected]>
|
|
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
Fixes: 6257dfc1c412 ("ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards")
Signed-off-by: Marek Vasut <[email protected]>
Signed-off-by: Alexandre Torgue <[email protected]>
|
|
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
Fixes: 6257dfc1c412 ("ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards")
Signed-off-by: Marek Vasut <[email protected]>
Signed-off-by: Alexandre Torgue <[email protected]>
|
|
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
Fixes: 6257dfc1c412 ("ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards")
Signed-off-by: Marek Vasut <[email protected]>
Signed-off-by: Alexandre Torgue <[email protected]>
|
|
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
Fixes: 6257dfc1c412 ("ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards")
Signed-off-by: Marek Vasut <[email protected]>
Signed-off-by: Alexandre Torgue <[email protected]>
|
|
This commit introduces Power over Data Line (PoDL) Power Source
Equipment (PSE) regulator nodes to the PRTT1C devicetree. The addition
of these nodes enables support for PoDL in PRTT1C devices, allowing
power delivery and data transmission over a single twisted pair.
The new PoDL PSE regulator nodes provide voltage capability information
of the current board design, which can be used as a hint for system
administrators when configuring and managing power settings. This
update enhances the versatility and simplifies the power management of
PRTT1C devices while ensuring compatibility with connected Powered
Devices (PDs).
After applying this patch, the power delivery can be controlled from
user space with a patched [1] ethtool version using the following commands:
ethtool --set-pse t1l2 podl-pse-admin-control enable
to enable power delivery, and
ethtool --show-pse t1l2
to display the PoDL PSE settings.
By integrating PoDL PSE support into the PRTT1C devicetree, users can
benefit from streamlined power and data connections in their
deployments, improving overall system efficiency and reducing cabling
complexity.
[1] https://lore.kernel.org/all/[email protected]/
Signed-off-by: Oleksij Rempel <[email protected]>
Signed-off-by: Alexandre Torgue <[email protected]>
|
|
The patch adds support for touchscreen on the stm32f746-disco board.
Signed-off-by: Dario Binacchi <[email protected]>
Signed-off-by: Alexandre Torgue <[email protected]>
|
|
Add pin configurations for using i2c3 controller on stm32f7.
Signed-off-by: Dario Binacchi <[email protected]>
Signed-off-by: Alexandre Torgue <[email protected]>
|
|
The revert commit 36a6418bb1259 ("Revert "ARM: dts: stm32: add CAN support
on stm32f746"") prevented parsing errors due to the lack of CAN3 binding.
Now that the binding definition for CAN3 is available in the mainline
thanks to commit 8f3ef556f8e1a ("dt-bindings: mfd: stm32f7: Add binding
definition for CAN3"), we can re-add the CAN support and make the driver
usable again.
Signed-off-by: Dario Binacchi <[email protected]>
Signed-off-by: Alexandre Torgue <[email protected]>
|
|
All boards using the DSI node duplicate the same pattern common pattern
in board DTs, that pattern is ports with endpoint labels and the same
in-SoC regulator connection. Move that common pattern into stm32mp157.dtsi
instead.
The two boards which do define panel@0 directly in the DSI bridge node now
have #address-cells/#size-cells in their board DT instead of it being in
stm32mp157.dtsi and activated incorrectly for all boards, even the ones
which use e.g. another DSI-to-something bridge.
Signed-off-by: Marek Vasut <[email protected]>
Acked-by: Raphaël Gallais-Pou <[email protected]>
Signed-off-by: Alexandre Torgue <[email protected]>
|
|
Enables use of GIC PPI#15 for OP-TEE asynchronous notifications
on stm32mp13 platforms.
Signed-off-by: Etienne Carriere <[email protected]>
Signed-off-by: Alexandre Torgue <[email protected]>
|
|
The Linux Automation Test Automation Controller (LXA TAC)[1] is an embedded
software development tool built around the Octavo Systems OSD32MP15x SiP.
The device contains an eMMC for storage, a DSA-capable on board ethernet
switch with two external ports, dual CAN busses, a power switch to turn
a device under test on or off and some other I/O.
As of now there are two STM32MP157 based hardware generations (Gen 1 and
Gen 2) that have most of their hardware config in common.
In the future there will also be a STM32MP153 based hardware generation.
[1]: https://www.linux-automation.com/en/products/lxa-tac.html
Signed-off-by: Leonard Göhrs <[email protected]>
Signed-off-by: Alexandre Torgue <[email protected]>
|
|
Add pinmux groups required for the Linux Automation GmbH TAC.
Signed-off-by: Leonard Göhrs <[email protected]>
Signed-off-by: Alexandre Torgue <[email protected]>
|
|
CFG_STM32MP1_SCMI_SHM_SYSRAM will be disabled by default for STM32MP13x
SoCs in future OP-TEE version and the OP-TEE SMCI server uses only
the OP-TEE native shared memory registered by clients.
To be compatible by default with this configuration this patch removes
the shared memory in the SCMI configuration and the associated reserved
memory in SRAM.
Fixes: 9005aeddd9fc ("ARM: dts: stm32: enable optee firmware and SCMI support on STM32MP13")
Signed-off-by: Patrick Delaunay <[email protected]>
Signed-off-by: Alexandre Torgue <[email protected]>
|
|
Since the OP-TEE commit "plat-stm32mp1: scmi_server: default use OP-TEE
shared memory", integrated in OP-TEE 3.22.0-rc1, the default configuration
for STM32MP15x SoCs changes and CFG_STM32MP1_SCMI_SHM_SYSRAM is disabled
by default and the OP-TEE SMCI server uses OP-TEE native shared memory
registered by clients.
To be compatible with this configuration and the next OP-TEE versions,
this patch removes in the STM32MP15 SCMI device tree the SHMEM used by
OP-TEE SCMI and the associated reserved memory in the last 4KByte page
of SRAM.
Fixes: ea3414e1249e ("ARM: dts: stm32: move SCMI related nodes in a dedicated file for stm32mp15")
Signed-off-by: Patrick Delaunay <[email protected]>
Signed-off-by: Alexandre Torgue <[email protected]>
|
|
The DTS code coding style expects exactly one space before and after '='
sign.
Reviewed-by: Alim Akhtar <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Krzysztof Kozlowski <[email protected]>
|
|
The DTS code coding style expects exactly one space before and after '='
sign.
Reviewed-by: Alim Akhtar <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Krzysztof Kozlowski <[email protected]>
|
|
The DTS code coding style expects exactly one space before and after '='
sign.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
spi-max-frequency is a property of SPI device, not SPI controller. Drop
it from the controller nodes. No functional impact expected, although
qcom-msm8960-samsung-expressatt board does not have any child SPI
devices thus the property disappears. This fixes dtbs_check warnings
like:
qcom-msm8960-cdp.dtb: spi@16080000: Unevaluated properties are not allowed ('spi-max-frequency' was unexpected)
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
spi-max-frequency is a property of SPI device, not SPI controller. Drop
it from the controller nodes. No functional impact expected because
child SPI device already defines spi-max-frequency. This fixes
dtbs_check warnings like:
qcom-ipq8064-ap148.dtb: spi@1a280000: Unevaluated properties are not allowed ('spi-max-frequency' was unexpected)
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
Initial introduction of Inventec Starscream x86 family
equipped with AST2600 BMC SoC.
Signed-off-by: Chen PJ <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Joel Stanley <[email protected]>
|
|
Device node names should be generic which is also expected by USB
bindings:
qcom-sdx55-t55.dtb: dwc3@a600000: $nodename:0: 'dwc3@a600000' does not match '^usb(@.*)?'
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
Device node names should be generic which is also expected by USB
bindings:
qcom-ipq4018-jalapeno.dtb: dwc3@6000000: $nodename:0: 'dwc3@6000000' does not match '^usb(@.*)?'
Override also the DWC3 node in qcom-ipq4018-ap120c-ac.dtsi by
label/phandle, not via node path, because it is less error-prone and
makes the overriding node-name independent.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
Add the DIMM SPD to the processor I2C busses.
Signed-off-by: Eddie James <[email protected]>
Reviewed-by: Joel Stanley <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Joel Stanley <[email protected]>
|
|
Add a node for the ocmem found on msm8226. It contains one region, used
as gmu_ram.
Reviewed-by: Konrad Dybcio <[email protected]>
Signed-off-by: Luca Weiss <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
Add the nodes that describe the mdss so that display can work on
MSM8226.
Signed-off-by: Luca Weiss <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>
|
|
Add missing whitespace between node name/label and opening {.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for
each SoC vendor, following the same scheme that is used on arm64, mips
and riscv. This has been discussed for many years, but so far we never
did this as there was a plan to move the files out of the kernel
entirely, which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along with
their device drivers.
- The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the
time.
- Amlogic C3 is a Cortex-A35 based smart IP camera chip
- Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
- Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
- Qualcomm SDX75 is the latest generation modem chip that is used as
a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
- Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
Xuantie C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those
included there are 39 new board files, but only five more 32-bit this
time, probably a new low:
- Marantec Maveo board based on dhcor imx6ull module
- Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
- Epson Moverio BT-200 AR glasses based on TI OMAP4
- PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
- ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than we had
in the recent releases:
- Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.
- NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234
- Qualcomm gains support for 6 reference boards on various members of
their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
of the various reference platforms for their new chips.
- Rockchips support for several newer boards: Indiedroid Nova
(rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
Fastrhino R66S/R68S (rk3568)
- TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
Verdin family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
- continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
- support for devicetree overlays on at91, bcm283x
- significant additions to existing SoC support on mediatek,
qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
STM32MP1
As usual, a lot more detail is available in the individual merge
commits"
* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
ARM: mvebu: fix unit address on armada-390-db flash
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
arm: dts: Enable device-tree overlay support for AT91 boards
arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
ARM: dts: at91: use generic name for shutdown controller
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
...
|
|
Pull ARM updates from Russell King:
- lots of build cleanups from Arnd spread throughout the arch/arm tree
- replace strlcpy() with the preferred strscpy()
- use sign_extend32() in the module linker
- drop handle_irq() machine descriptor method
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9315/1: fiq: include asm/mach/irq.h for prototypes
ARM: 9314/1: tcm: move tcm_init() prototype to asm/tcm.h
ARM: 9313/1: vdso: add missing prototypes
ARM: 9312/1: vfp: include asm/neon.h in vfpmodule.c
ARM: 9311/1: decompressor: move function prototypes to misc.h
ARM: 9310/1: xip-kernel: add __inflate_kernel_data prototype
ARM: 9309/1: add missing syscall prototypes
ARM: 9308/1: move setup functions to header
ARM: 9307/1: nommu: include asm/idmap.h
ARM: 9306/1: cacheflush: avoid __flush_anon_page() missing-prototype warning
ARM: 9305/1: add clear/copy_user_highpage declarations
ARM: 9304/1: add prototype for function called only from asm
ARM: 9303/1: kprobes: avoid missing-declaration warnings
ARM: 9302/1: traps: hide unused functions on NOMMU
ARM: 9301/1: dma-mapping: hide unused dma_contiguous_early_fixup function
ARM: 9300/1: Replace all non-returning strlcpy with strscpy
ARM: 9299/1: module: use sign_extend32() to extend the signedness
ARM: 9298/1: Drop custom mdesc->handle_irq()
|
|
The unit address needs to be changed to match the reg property:
arch/arm/boot/dts/marvell/armada-390-db.dts:84.10-106.4: Warning (spi_bus_reg): /soc/spi@10680/flash@1: SPI bus unit address format error, expected "0"
Reported-by: Stephen Rothwell <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into soc/dt
ARM: dts: Move .dts files to vendor sub-directories
The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.
* tag 'arm-dts-mv-for-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.
There's no change to dtbs_install as the flat structure is maintained on
install.
The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
company (e.g. gemini, nspire)
The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.
Acked-by: Viresh Kumar <[email protected]>
Acked-by: Michal Simek <[email protected]> #Xilinx
Acked-by: Krzysztof Kozlowski <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Acked-by: Paul Barker <[email protected]>
Acked-by: Tony Lindgren <[email protected]>
Acked-by: Gregory CLEMENT <[email protected]>
Acked-by: Heiko Stuebner <[email protected]>
Acked-by: Wei Xu <[email protected]> #hisilicon
Acked-by: Geert Uytterhoeven <[email protected]>
Acked-by: Nick Hawkins <[email protected]>
Acked-by: Baruch Siach <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Acked-by: Andre Przywara <[email protected]>
Reviewed-by: Claudiu Beznea <[email protected]>
Acked-by: Peter Rosin <[email protected]>
Acked-by: Jesper Nilsson <[email protected]>
Acked-by: Sudeep Holla <[email protected]>
Acked-by: Florian Fainelli <[email protected]> #broadcom
Acked-by: Manivannan Sadhasivam <[email protected]>
Reviewed-by: Jisheng Zhang <[email protected]>
Acked-by: Patrice Chotard <[email protected]>
Acked-by: Romain Perier <[email protected]>
Acked-by: Alexandre TORGUE <[email protected]>
Acked-by: Shawn Guo <[email protected]>
Acked-by: Kunihiko Hayashi <[email protected]>
Acked-by: Enric Balletbo i Serra <[email protected]>
Signed-off-by: Rob Herring <[email protected]>
|
|
Comparing .dts files to built .dtb files yielded a few .dts files which
are never built. Add them to the build.
Signed-off-by: Rob Herring <[email protected]>
|
|
In preparation to move .dts files into subdirectories, include
sunxi-h3-h5-emlid-neutis.dtsi from the current directory rather than the
symlinked include path.
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Rob Herring <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/dt
AT91 DT for 6.5 #2
It contains:
- generic names for shutdown controller nodes
- enablement of DT overlay support for some AT91 boards
- fix reset and SPI CS for lan966x-kontron-kswitch-d10-mmt based boards
- addition of PHY interrupts for lan966x-kontron-kswitch-d10-mmt-8g
board
* tag 'at91-dt-6.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
ARM: dts: at91: use generic name for shutdown controller
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
With interrupt handling fixed in the MaxLinear PHY driver, see commit
97a89ed101bb ("net: phy: mxl-gpy: disable interrupts on GPY215 by
default"), we can finally add the correct interrupt description to the
device tree.
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Claudiu Beznea <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The pinctrl node was missing which change the pin mux to GPIO mode.
Add it so we don't have to rely on the bootloader to set the correct
mode.
Fixes: 79d83b3a458e ("ARM: dts: lan966x: add basic Kontron KSwitch D10 support")
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Claudiu Beznea <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The pinctrl node was missing which change the pin mux to GPIO mode. Add
it.
Fixes: 79d83b3a458e ("ARM: dts: lan966x: add basic Kontron KSwitch D10 support")
Signed-off-by: Michael Walle <[email protected]>
[claudiu.beznea: moved pinctrl-* bindings after compatible]
Signed-off-by: Claudiu Beznea <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add the '-@' DTC option for AT91 boards that have device-tree overlays.
This option populates the '__symbols__' node that contains all the
necessary symbols for supporting device-tree overlays (from bootloader)
on these devices.
This change increases the size of the resulting DTB with ~30%-40%. Below
are the measurements performed v6.4-rc6:
at91-sam9x60_curiosity.dtb 28499 -> 36641 bytes
at91-sam9x60ek.dtb 30867 -> 39609 bytes
at91-sama5d27_som1_ek.dtb 26086 -> 34166 bytes
at91-sama5d27_wlsom1_ek.dtb 26045 -> 33184 bytes
at91-sama5d2_icp.dtb 27521 -> 36155 bytes
at91-sama5d2_ptc_ek.dtb 23237 -> 29612 bytes
at91-sama5d2_xplained.dtb 27262 -> 35326 bytes
at91-sama5d3_eds.dtb 27924 -> 39939 bytes
at91-sama5d3_xplained.dtb 28400 -> 40650 bytes
at91-sama5d4_xplained.dtb 26456 -> 36107 bytes
at91-sama7g5ek.dtb 29212 -> 37289 bytes
Signed-off-by: Cristian Birsan <[email protected]>
[claudiu.beznea: s/arm: dts/ARM: dts: at91/ in commit title]
Signed-off-by: Claudiu Beznea <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
https://github.com/Broadcom/stblinux into soc/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 6.5, please pull the following:
- Krzysztof adds missing cache properties for the BCM63xx DSL routers
- Rafal relicenses a number of the BCM5301X DTS files to the GPL 2.0+ / MIT license,
and he fixes a number of Device Tree nodes warnings, adds MAC address
for all Luxul routers and adds Netgear R8000 Wi-Fi regulatory
information to the DTS
- Stanislav updates the "BCM mobile" SoCs DTS files to fix various
warnings
- Aurelien enables the BCM283x DTS files to be built with relocation
information to make them usable with DT overlays
- Christian fixes the Meraki DTS to have correct NAND ECC properties,
correct partition numbers and fixed-link node(s) properties
* tag 'arm-soc/for-6.5/devicetree' of https://github.com/Broadcom/stblinux: (33 commits)
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
ARM: dts: BCM5301X: Add Netgear R8000 WiFi regulator mappings
dt-bindings: net: wireless: brcm,bcm4329-fmac: allow generic properties
dt-bindings: net: wireless: brcm,bcm4329-fmac: add BCM4366 binding
ARM: dts: BCM5301X: fix duplex-full => full-duplex
ARM: dts: BCM5301X: MR32: remove partition index numbers
ARM: dts: BCM5301X: MR26: MR32: remove bogus nand-ecc-algo property
dt-bindings: power: reset: bcm21664-resetmgr: convert to YAML
ARM: dts: bcm21664-garnet: use node labels
ARM: dts: bcm11351/21664: add UART, I2C node labels
ARM: dts: bcm-mobile: move status properties to the end of nodes
ARM: dts: bcm21664/23550: use CCU compatibles directly
ARM: dts: bcm-mobile: change "" includes to <> where applicable
ARM: dts: BCM5301X: Describe switch ports in the main DTS
ARM: dts: BCM5301X: Relicense Christian's code to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Drop invalid properties from Meraki MR32 keys
ARM: dts: BCM5301X: Drop invalid #usb-cells
dt-bindings: arm: bcm: Add bindings for Buffalo WZR-1166DHP(2)
ARM: dts: BCM5301X: Use updated "spi-gpio" binding properties
...
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Add the '-@' DTC option for AT91 boards that have device-tree overlays.
This option populates the '__symbols__' node that contains all the
necessary symbols for supporting device-tree overlays (from bootloader)
on these devices.
This change increases the size of the resulting DTB with ~30%-40%. Below
are the measurements performed v6.4-rc6:
at91-sam9x60_curiosity.dtb 28499 -> 36641 bytes
at91-sam9x60ek.dtb 30867 -> 39609 bytes
at91-sama5d27_som1_ek.dtb 26086 -> 34166 bytes
at91-sama5d27_wlsom1_ek.dtb 26045 -> 33184 bytes
at91-sama5d2_icp.dtb 27521 -> 36155 bytes
at91-sama5d2_ptc_ek.dtb 23237 -> 29612 bytes
at91-sama5d2_xplained.dtb 27262 -> 35326 bytes
at91-sama5d3_eds.dtb 27924 -> 39939 bytes
at91-sama5d3_xplained.dtb 28400 -> 40650 bytes
at91-sama5d4_xplained.dtb 26456 -> 36107 bytes
at91-sama7g5ek.dtb 29212 -> 37289 bytes
Signed-off-by: Cristian Birsan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into soc/dt
mvebu dt for 6.5 (part 1)
Add Endian 4i Edge 200 board (kirkwood based)
Add missing phy-modes on Armada 388 clearfog board
Replace deprecated spi-gpio properties on Armada XP
Align MTD partition nodes to dtschema for all mvebu boards
* tag 'mvebu-dt-6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: mvebu: align MTD partition nodes to dtschema
ARM: dts: armada-xp: Replace deprecated spi-gpio properties
ARM: dts: armada388-clearfog: add missing phy-modes
ARM: dts: kirkwood: Add Endian 4i Edge 200 board
Link: https://lore.kernel.org/r/87a5wzh8b1.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into soc/dt
Keystone2 device tree updates for v6.5
Cosmetic cleanups:
* Do not capitalize hex digits
* Unify pinctrl-single pin group nodes for keystone
* Fix eeprom node names
* tag 'ti-keystone-dt-for-v6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
ARM: dts: keystone: Do not capitalize hex digits
ARM: dts: keystone: Remove ti,keystone from soc node compatible
ARM: dts: keystone: Fix EEPROM node names
ARM: dts: Unify pinctrl-single pin group nodes for keystone
Link: https://lore.kernel.org/r/20230615164127.qcgwrbwpmclx5wlm@landscape
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
More Qualcomm ARM32 DeviceTree updates for v6.5
On MSM8960, support for USB is added and the Samsung Galaxy Express is
added.
GPIO keys and on-board LEDs are described for the APQ8074 Dragonboard.
On MSM8226, QFPROM, tsens and thermal zones are defined, and the
description of the clock hierarchy is improved.
The PCIe endpoint controller on SDX55 gains a interconnect path to DDR
defined.
Sony Xperia X2 Tablet and Samsung Galaxy Tab 4 are updated following
changes in the LP855X DeviceTree binding.
* tag 'qcom-dts-for-6.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm: dts: qcom: sdx55: Add interconnect path
ARM: dts: qcom: msm8226: Add thermal zones node
ARM: dts: qcom: msm8226: Add tsens node and related nvmem cells
ARM: dts: qcom: msm8226: Add qfprom node
ARM: dts: qcom: pm8941: Add thermal zone config
ARM: dts: qcom: pm8841: Add thermal zone config
ARM: dts: qcom: pm8226: Add thermal sensor and thermal zone config
ARM: dts: qcom: msm8974: rename labels for DSI nodes
ARM: dts: qcom: apq8074-dragonboard: add gpio keys
ARM: dts: qcom: apq8074-dragonboard: add onboard leds
ARM: dts: qcom: Add Samsung Galaxy Express support
ARM: dts: qcom: msm8960: Add USB node
ARM: dts: qcom: adapt to LP855X bindings changes
ARM: dts: qcom: msm8226: Provide clocks to mmcc node
ARM: dts: qcom: msm8226: Use XO from rpmcc where possible
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into soc/dt
MT7530 (e.g. BPI R2):
- several DT clean-ups
- add port5 as CPU port
* tag 'v6.4-next-dts32' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm: dts: mt7623: add port@5 as CPU port
arm: dts: mt7623: enable flow control on port@6
arm: dts: mt7623: change mt7530 switch address
arm: dts: mt7623: add mt7530 switch to mt7623a.dtsi
arm: dts: mt7623: add gmacs to mt7623.dtsi
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|