aboutsummaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts
AgeCommit message (Collapse)AuthorFilesLines
2023-09-27ARM: dts: qcom: apq8026-samsung-matisse-wifi: Fix inverted hall sensorMatti Lehtimäki1-2/+2
Fix hall sensor GPIO polarity and also allow disabling the sensor. Remove unneeded interrupt. Fixes: f15623bda1dc ("ARM: dts: qcom: Add support for Samsung Galaxy Tab 4 10.1 (SM-T530)") Signed-off-by: Matti Lehtimäki <[email protected]> Reviewed-by: Luca Weiss <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Bjorn Andersson <[email protected]>
2023-09-27ARM: dts: qcom: msm8226: Add blsp1_i2c6 and blsp1_uart2Luca Weiss1-0/+33
Add more busses found on msm8226 SoC. Signed-off-by: Luca Weiss <[email protected]> Reviewed-by: Dmitry Baryshkov <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Linus Walleij <[email protected]>
2023-09-26ARM: dts: omap: omap4-embt2ws: Let IMU driver handle Magnetometer internallyAndreas Kemnade1-9/+0
Possibility to use the i2c gate is only for compatibility reasons, so avoid messing around with additional i2c busses. Signed-off-by: Andreas Kemnade <[email protected]> Message-ID: <[email protected]> Signed-off-by: Tony Lindgren <[email protected]>
2023-09-26ARM: dts: am335x-pocketbeagle: add missing GPIO muxTrevor Woerner1-0/+9
Add the default MODE setting of a GPIO pin that was missing from the device tree (i.e. P2.20/gpio2_00). This is to ensure the GPIO pins match the pocketbeagle wiring expectations. Signed-off-by: Trevor Woerner <[email protected]> Message-ID: <[email protected]> [[email protected]: leave out extra line break] Signed-off-by: Tony Lindgren <[email protected]>
2023-09-26ARM: dts: am335x-pocketbeagle: enable pruTrevor Woerner1-10/+36
Now that the PRU code is upstream and can be loaded via remoteproc, adjust the device tree to enable it and adjust the pin muxing so that the default setting of the pins matches what's is given on the silkscreen and/or pocketbeagle wiring. Caveat: In most cases, the silkscreen will indicate, for example, "PRU0.7", but it doesn't indicate whether that pin should be enabled for input or output. On the PRU a different MODE is used for input versus output. So it is unclear which mode to enable (MODE5 = output, MODE6 = input). In cases where there is a choice (PRU1.11, PRU0.7, PRU0.4, PRU0.1, PRU1.10, PRU0.6, PRU0.3, PRU0.2, and PRU0.5) output is assumed (MODE5). The remaining PRU silkscreen pins do not have a choice and are set as follows: PRU0.16 MODE5 input PRU0.15i MODE6 input Signed-off-by: Trevor Woerner <[email protected]> Message-ID: <[email protected]> [[email protected]: formatted description to fit 75 characters] Signed-off-by: Tony Lindgren <[email protected]>
2023-09-26ARM: dts: am335x-pocketbeagle: remove dependency cycleTrevor Woerner1-5/+0
Remove the self-referenceing "pinctrl-0" entry inside the pinmux clause. This eliminates the set of boot messages (one for each referenced pin) similar to the following: platform 44e10800.pinmux: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@10000/scm@0/pinmux@800/pinmux_P2_17_gpio Signed-off-by: Trevor Woerner <[email protected]> Message-ID: <[email protected]> Signed-off-by: Tony Lindgren <[email protected]>
2023-09-26ARM: dts: am335x-pocketbeagle: update LED informationTrevor Woerner1-0/+9
Add the "color" and "description" properties. Signed-off-by: Trevor Woerner <[email protected]> Message-ID: <[email protected]> Signed-off-by: Tony Lindgren <[email protected]>
2023-09-26ARM: dts: omap4: embt2ws: add LEDAndreas Kemnade1-1/+26
Add LED since the driver is now available. Signed-off-by: Andreas Kemnade <[email protected]> Message-ID: <[email protected]> Signed-off-by: Tony Lindgren <[email protected]>
2023-09-25ARM: dts: st: href-tvk1281618: correct touchscreen syna,nosleep-modeKrzysztof Kozlowski1-1/+1
There is no syna,nosleep property in Synaptics RMI4 touchscreen: ste-hrefprev60-tvk.dtb: synaptics@4b: rmi4-f01@1: 'syna,nosleep' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by: Krzysztof Kozlowski <[email protected]> Message-ID: <[email protected]> Signed-off-by: Linus Walleij <[email protected]>
2023-09-25ARM: dts: st: href-tvk1281618: fix touchscreen VIO supplyKrzysztof Kozlowski1-1/+1
According to bindings and Linux driver, there is no VDDIO but VIO supply: ste-hrefprev60-tvk.dtb: synaptics@4b: Unevaluated properties are not allowed ('vddio-supply' was unexpected) Signed-off-by: Krzysztof Kozlowski <[email protected]> Message-ID: <[email protected]> Signed-off-by: Linus Walleij <[email protected]>
2023-09-25ARM: dts: renesas: rskrza1: Add FLASH nodesGeert Uytterhoeven1-0/+66
Add device nodes for the dual Spansion S25FL512S QSPI NOR FLASH and the Spansion S29GL512S CFI NOR FLASH on the RSK+RZA1 development board. The former is mapped directly through the SPI Multi I/O Bus Controller. The latter resides in the external address space of the Bus State Controller (BSC). Signed-off-by: Geert Uytterhoeven <[email protected]> Link: https://lore.kernel.org/r/17a221699da14639e72264ffa39d47592d470f9a.1693481518.git.geert+renesas@glider.be
2023-09-25ARM: dts: renesas: genmai: Add FLASH nodesGeert Uytterhoeven1-0/+85
Add device nodes for the dual Spansion S25FL512S QSPI NOR FLASH and the two Spansion S29GL512S CFI NOR FLASHes on the Genmai development board. The former is mapped directly through the SPI Multi I/O Bus Controller. The latter reside in the address space of the Bus State Controller (BSC). Signed-off-by: Geert Uytterhoeven <[email protected]> Link: https://lore.kernel.org/r/53c89c70c6b010702fd9ab5247e19986857671ba.1693481518.git.geert+renesas@glider.be
2023-09-25ARM: dts: renesas: wheat: Move Ethernet node to LBSCGeert Uytterhoeven1-16/+18
The SMSC LAN89218AQ Ethernet controller on the Wheat development board resides in the external address space of the Local Bus State Controller (LBSC). Move the Ethernet device node to reflect this. Signed-off-by: Geert Uytterhoeven <[email protected]> Link: https://lore.kernel.org/r/a291c2750144df29e69824d5b9d76cbc11f613c1.1693481518.git.geert+renesas@glider.be
2023-09-25ARM: dts: renesas: blanche: Move Ethernet node to LBSCGeert Uytterhoeven1-15/+17
The SMSC LAN89218AQ Ethernet controller on the Blanche development board resides in the external address space of the Local Bus State Controller (LBSC). Move the Ethernet device node to reflect this. Signed-off-by: Geert Uytterhoeven <[email protected]> Link: https://lore.kernel.org/r/457239047bc8b5deabf15d816043a89ab00db5ef.1693481518.git.geert+renesas@glider.be
2023-09-25ARM: dts: renesas: marzen: Move Ethernet node to LBSCGeert Uytterhoeven1-15/+17
The SMSC LAN89218AQ Ethernet controller on the Marzen development board resides in the external address space of the Local Bus State Controller (LBSC). Move the Ethernet device node to reflect this. Signed-off-by: Geert Uytterhoeven <[email protected]> Link: https://lore.kernel.org/r/74a8ee61ed89c9ca0489156a4f135ecb825e56b9.1693481518.git.geert+renesas@glider.be
2023-09-25ARM: dts: renesas: r8a7792: Add LBSC nodeGeert Uytterhoeven1-0/+7
Add a minimal device node for the Local Bus State Controller (LBSC) on the R-Car V2H SoC, to be extended by board DTS files for devices residing in the LBSC external address space. Signed-off-by: Geert Uytterhoeven <[email protected]> Link: https://lore.kernel.org/r/182fce2257679f6a8963ecb77aae68af617556d1.1693481518.git.geert+renesas@glider.be
2023-09-25ARM: dts: renesas: r8a7779: Add LBSC nodeGeert Uytterhoeven1-0/+7
Add a minimal device node for the Local Bus State Controller (LBSC) on the R-Car H1 SoC, to be extended by board DTS files for devices residing in the LBSC external address space. Signed-off-by: Geert Uytterhoeven <[email protected]> Link: https://lore.kernel.org/r/2d0a6054306b4975355e65fe012f860ec00fcf55.1693481518.git.geert+renesas@glider.be
2023-09-25ARM: dts: renesas: r7s72100: Add BSC nodeGeert Uytterhoeven1-0/+7
Add a minimal device node for the Bus State Controller (BSC) on the RZ/A1H SoC, to be extended by board DTS files for devices residing in the BSC external address space. Signed-off-by: Geert Uytterhoeven <[email protected]> Link: https://lore.kernel.org/r/ccab4fa198225edcd3750f62532a1ee3c6d2a109.1693481518.git.geert+renesas@glider.be
2023-09-25ARM: dts: renesas: Remove unused LBSC nodes from board DTSGeert Uytterhoeven7-35/+0
Several board DTS files contain minimal device nodes that represent on-SoC Local Bus State Controllers (LBSC), although they belong in the SoC-specific DTS files instead. As these device nodes are incomplete and unused, and hamper adding proper nodes later, it is better to just remove them. Signed-off-by: Geert Uytterhoeven <[email protected]> Link: https://lore.kernel.org/r/76ece7602045670cbb8dff684c3366ba6eb89add.1693481518.git.geert+renesas@glider.be
2023-09-25ARM: dts: imx53: Adjust the ecspi compatibleFabio Estevam1-2/+2
Per fsl-imx-cspi.yaml, "fsl,imx53-ecspi" should not contain addtional compatible entries. Change it accordingly to fix the following schema warning: spi@63fac000: compatible: 'oneOf' conditional failed, one must be fixed: ['fsl,imx53-ecspi', 'fsl,imx51-ecspi'] is too long Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: imx7ulp: Fix usbphy1 compatibleFabio Estevam1-1/+1
Per fsl,mxs-usbphy.yaml, fsl,imx7ulp-usbphy is not compatible with fsl,imx6ul-usbphy. Remove 'fsl,imx6ul-usbphy' from the compatible string to fix the following schema warning: imx7ulp-com.dtb: usb-phy@40350000: compatible: 'oneOf' conditional failed, one must be fixed: ['fsl,imx7ulp-usbphy', 'fsl,imx6ul-usbphy'] is too long Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: imx6q-pistachio: Use a valid value for fsl,tx-d-calFabio Estevam1-2/+2
Passing 5 to fsl,tx-d-cal is not valid as per fsl,mxs-usbphy.yaml: imx6q-pistachio.dtb: usbphy@20c9000: fsl,tx-d-cal:0:0: 5 is less than the minimum of 79 from schema $id: http://devicetree.org/schemas/phy/fsl,mxs-usbphy.yaml# Pass the minimum value of 79 instead. Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: imx6q-b650v3: Fix fsl,tx-cal-45-dn-ohmsFabio Estevam1-2/+2
Passing 55 to fsl,tx-cal-45-dn-ohms is not valid as per fsl,mxs-usbphy.yaml: imx6q-b650v3.dtb: usbphy@20c9000: fsl,tx-cal-45-dn-ohms:0:0: 55 is greater than the maximum of 54 from schema $id: http://devicetree.org/schemas/phy/fsl,mxs-usbphy.yaml# Pass the maximum value of 54 instead. Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: imx28-tx28: Move phy_type to USB nodeFabio Estevam1-2/+2
phy_type is a property for the USB controller, not for the USB PHY. Move it to the USB controller nodes to fix the following schema warning: imx28-tx28.dtb: usbphy@8007c000: 'phy_type' does not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/phy/fsl,mxs-usbphy.yaml Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: mxs: Switch to #pwm-cells = <3>Fabio Estevam15-15/+15
mxs-pwm.yaml documents that #pwm-cells should be 3. This is correct as the last cell may indicate the PWM polarity. Convert all mxs devicetree files to using #pwm-cells = <3> for consistency. Signed-off-by: Fabio Estevam <[email protected]> Reviewed-by: Uwe Kleine-König <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: imx6q: Add Variscite MX6 Custom board supportJames Hilliard2-0/+248
This patch adds support for the Variscite MX6 SoM Carrier Board. This Carrier-Board has the following : - LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display - HDMI Connector - USB Host + USB OTG Connector - 10/100/1000 Mbps Ethernet - miniPCI-Express slot - SD Card connector - Audio Headphone/Line In jack connectors - S-ATA - On-board DMIC - RS485 Header - CAN bus header - SPI header - Camera Interfaces header - OnBoard RTC with Coin Backup battery socket - RS232 Debug Header (IDC10) - RS232 DTE Product Page : https://www.variscite.com/product/single-board-computers/var-mx6customboard The dts file based on the ones provided by Variscite on their own kernel, but adapted for mainline. Cc: Pierluigi Passaro <[email protected]> Reviewed-by: Fabio Estevam <[email protected]> Signed-off-by: Gregory CLEMENT <[email protected]> Signed-off-by: James Hilliard <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: imx6qdl: Add Variscite VAR-SOM-MX6 SoM supportJames Hilliard1-0/+569
This patch adds support for the Variscite VAR_SOM-MX6 SoM with : - i.MX6 Quad or Dual Lite SoC - 256 – 4096 MB DDR3 - 4-64 GB eMMC - 128 – 1024 MB SLC NAND - Camera Interface - HDMI+CEC interface - LVDS / DSI / Parallel RGB interfaces - Ethernet RGMII interface - On-SoM Wi-Fi/Bluetooth with WiLink wl183x SDIO Module - SD/MMC/SDIO interface - USB Host + USB OTG interface - I2C interfaces - SPI interfaces - PCI-Express 2.0 interface - on-SoM Audio Codec with HP/Line-In interfaces + DMIC interface - Digital Audio interface - S/PDIF interface Product website : https://www.variscite.com/product/system-on-module-som/cortex-a9/var-som-mx6-cpu-freescale-imx6/ Support is handled with a SoM-centric dtsi exporting the default interfaces along the default pinmuxing to be enabled by the board dts file. This file is based on the one provided by Variscite on their own kernel, but adapted for mainline. Cc: Pierluigi Passaro <[email protected]> Reviewed-by: Fabio Estevam <[email protected]> Signed-off-by: Gregory CLEMENT <[email protected]> Signed-off-by: James Hilliard <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: mxs: Fix duart clock-namesFabio Estevam2-2/+2
Per pl011.yaml, the first entry of clock-names should be "uartclk". Change it accordingly to fix the following schema warning: imx23-xfi3.dtb: serial@80070000: clock-names:0: 'uartclk' was expected The pl011 driver does not search for the clock name, so this change is safe and was tested on a imx28-evk board. Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: imx6ull/7d-colibri: Fix compatibleFabio Estevam13-14/+6
Fix the imx6ull/7d-colibri devicetrees as per the rules defined at fsl.yaml. Signed-off-by: Fabio Estevam <[email protected]> Reviewed-by: Marcel Ziswiler <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: imx6ull-phytec-tauri: Fix compatibleFabio Estevam2-4/+4
Per fsl.yaml, the order of the compatible strings are not correct for imx6ull-phytec-tauri-emmc and imx6ull-phytec-tauri-nand. Fix them accordingly. Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: imx6ull-phytec-tauri: Remove board model and compatibleFabio Estevam1-5/+0
The imx6ull-phytec-tauri.dtsi file is included in two places: imx6ull-phytec-tauri-emmc.dts imx6ull-phytec-tauri-nand.dts These two files overwrite the board model and compatible locally, so there is no need for describing them in imx6ull-phytec-tauri.dtsi. Remove the board model and compatible. Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: imx7s: Fix CSI clocksFabio Estevam1-4/+2
Per nxp,imx7-csi.yaml, there is only one CSI clock entry. Fix it. This fixes the following schema warnings: imx7d-zii-rpu2.dtb: csi@30710000: clocks: [[1, 413], [1, 326], [1, 413]] is too long from schema $id: http://devicetree.org/schemas/media/nxp,imx7-csi.yaml# imx7d-zii-rpu2.dtb: csi@30710000: clock-names:0: 'mclk' was expected from schema $id: http://devicetree.org/schemas/media/nxp,imx7-csi.yaml# imx7d-zii-rpu2.dtb: csi@30710000: clock-names: ['axi', 'mclk', 'dcic'] is too long from schema $id: http://devicetree.org/schemas/media/nxp,imx7-csi.yaml# Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: imx51-zii-rdu1: Use preferred i2c-gpios propertiesFabio Estevam1-2/+2
The 'gpios' property to describe the SDA and SCL GPIOs is considered deprecated according to i2c-gpio.yaml. Switch to the preferred 'sda-gpios' and 'scl-gpios' properties. This fixes the following schema warnings: imx51-zii-rdu1.dtb: i2c-gpio: 'sda-gpios' is a required property from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml# imx51-zii-rdu1.dtb: i2c-gpio: 'scl-gpios' is a required property from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml# Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: imx6ul-tx6ul: Use preferred i2c-gpios propertiesFabio Estevam1-4/+2
The 'gpios' property to describe the SDA and SCL GPIOs is considered deprecated according to i2c-gpio.yaml. Switch to the preferred 'sda-gpios' and 'scl-gpios' properties. This fixes the following schema warnings: imx6ul-tx6ul-0011.dtb: i2c-gpio: 'sda-gpios' is a required property from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml# imx6ul-tx6ul-0011.dtb: i2c-gpio: 'scl-gpios' is a required property from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml# Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: imx6qdl-gw591: Remove lis2de12 interrupt-namesFabio Estevam2-2/+0
According to st,st-sensors.yaml, the 'interrupt-names' property is not a valid one. Remove it to fix the following schema warnings: imx6dl-gw5912.dtb: accel@19: 'interrupt-names' does not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/iio/st,st-sensors.yaml# Signed-off-by: Fabio Estevam <[email protected]> Acked-by: Tim Harvey <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: imx6qdl-gw5904: add internal mdio nodesTim Harvey1-0/+29
Complete the switch definition by adding the internal mdio nodes. This does not change behavior on Linux but is required if the dt is used for U-Boot which requires the internal PHY ports to be defined for DSA. Signed-off-by: Tim Harvey <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-25ARM: dts: imx: add support for the ATM0700D4 panel attached to sk-imx53Dmitry Baryshkov4-0/+256
The SK-ATM0700D4-Plug is an extension board (provided by the same manufacturer, [1]) which can be connected to the SK-IMX53 panel kit. The panel can be connected either using the RGB parallel bus or using the LVDS connector (recommended). Add DT files describing this "shield", both RGB and LVDS connections. [1] http://starterkit.ru/html/index.php?name=shop&op=view&id=64 Signed-off-by: Dmitry Baryshkov <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-24ARM: dts: nuvoton: add missing space before {Krzysztof Kozlowski3-5/+5
Add missing whitespace between node name/label and opening {. Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Krzysztof Kozlowski <[email protected]>
2023-09-24ARM: dts: mediatek: minor whitespace cleanup around '='Krzysztof Kozlowski2-3/+3
The DTS code coding style expects exactly one space before and after '=' sign. Reviewed-by: AngeloGioacchino Del Regno <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Krzysztof Kozlowski <[email protected]>
2023-09-24ARM: dts: mediatek: add missing space before {Krzysztof Kozlowski2-30/+30
Add missing whitespace between node name/label and opening {. Reviewed-by: AngeloGioacchino Del Regno <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Krzysztof Kozlowski <[email protected]>
2023-09-24ARM: dts: omap3-devkit8000: correct ethernet reg addresses (split)Krzysztof Kozlowski1-2/+2
The davicom,dm9000 Ethernet Controller accepts two reg addresses. Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Krzysztof Kozlowski <[email protected]>
2023-09-24ARM: dts: nxp: imx6qdl-nitrogen6: correct regulator node nameKrzysztof Kozlowski1-1/+1
Root node is not a bus, thus top-level nodes do not have unit addresses. Signed-off-by: Krzysztof Kozlowski <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-24ARM: dts: imx6ul: mba6ulx: Fix gpio-keys button node namesAlexander Stein1-3/+3
Numbers are separated by dashes. Fixes the warnings: arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2-mba6ulx.dtb: gpio-keys: 'button1', 'button2', 'button3' do not match any of the regexes: '^(button|event|key|switch|(button|event|key|switch)-[a-z0-9-]+|[a-z0-9-]+-(button|event|key|switch))$', 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/input/gpio-keys.yaml# Signed-off-by: Alexander Stein <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-24ARM: dts: imx6ul: mba6ulx: Mark gpio-buttons as wakeup-sourceAlexander Stein1-0/+3
I2C expander is capable of generating an IRQ during powersave, so the attached buttons can be used for waking up the system. Signed-off-by: Alexander Stein <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2023-09-23ARM: dts: qcom: sdx65-mtp: Specify PM7250B SID to useLuca Weiss1-0/+4
Now that the pm7250b.dtsi can be configured to be on a different SID, we also need to specify it for this dts file. Set it to the SID 2/3 like it was before commit 8e2d56f64572 ("arm64: dts: qcom: pm7250b: make SID configurable"). Fixes: 8e2d56f64572 ("arm64: dts: qcom: pm7250b: make SID configurable") Signed-off-by: Luca Weiss <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Bjorn Andersson <[email protected]>
2023-09-22ARM: dts: aspeed: bonnell: Add reserved memory for TPM event logEddie James1-1/+7
Trusted boot support requires the platform event log passed up from the bootloader. In U-Boot, this can now be accomplished with a reserved memory region, so add a region for this purpose to the Bonnell BMC devicetree. Signed-off-by: Eddie James <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Joel Stanley <[email protected]>
2023-09-19ARM: dts: qcom: drop incorrect cell-index from SPMIKrzysztof Kozlowski2-2/+0
The SPMI controller (PMIC Arbiter) does not use nor allow 'cell-index' property: qcom-sdx55-mtp.dtb: spmi@c440000: Unevaluated properties are not allowed ('cell-index' was unexpected) Signed-off-by: Krzysztof Kozlowski <[email protected]> Reviewed-by: Konrad Dybcio <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Bjorn Andersson <[email protected]>
2023-09-19ARM: dts: qcom-sdx55: switch PCIe QMP PHY to new style of bindingsDmitry Baryshkov1-19/+12
Change the PCIe QMP PHY to use newer style of QMP PHY bindings (single resource region, no per-PHY subnodes). Reviewed-by: Konrad Dybcio <[email protected]> Signed-off-by: Dmitry Baryshkov <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Bjorn Andersson <[email protected]>
2023-09-18ARM: dts: at91/trivial: fix typo in crypto DT namingNicolas Ferre1-1/+1
Fix typo in DT name for TDES node. Signed-off-by: Nicolas Ferre <[email protected]> Reviewed-by: Tudor Ambarus <[email protected]> Link: https://lore.kernel.org/r/[email protected] [claudiu.beznea: removed fixes tag as tdes node is not referenced anywhere by its node name] Signed-off-by: Claudiu Beznea <[email protected]>
2023-09-14ARM: dts: samsung: exynos4210: enable pollingMateusz Majewski1-2/+10
It seems that thermal in Exynos 4210 is broken without this, as it will never decrease cooling after increasing it. Signed-off-by: Mateusz Majewski <[email protected]> Link: https://lore.kernel.org/r/[email protected] [krzk: fix comment coding style and line wrapping] Signed-off-by: Krzysztof Kozlowski <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.