Age | Commit message (Collapse) | Author | Files | Lines |
|
Add conditional constraint to make property "reset-gpios" available only
for compatible devices acually having the reset pin.
Make property "brcm,requires-autobaud-mode" depend on property
"shutdown-gpios" as the shutdown pin is required to enter autobaud mode.
I looked at all compatible devices and compiled the matrix below before
formulating the conditional constraint. This was a pure paper exercise and
no verification testing has been performed.
d
e
v h
i o
c s
s e t
h - -
u w w v
t r a a v d
d e k k b d
o s e e a i
w e u u t o
n t p p - -
- - - - s s
g g g g u u
p p p p t p p
i i i i x l p p
o o o o c p l l
s s s s o o y y
---------------------------------------
brcm,bcm20702a1 X X X X X X X X
brcm,bcm4329-bt X X X X X X X X
brcm,bcm4330-bt X X X X X X X X
brcm,bcm4334-bt X - X X X X X X
brcm,bcm43438-bt X - X X X X X X
brcm,bcm4345c5 X - X X X X X X
brcm,bcm43540-bt X - X X X X X X
brcm,bcm4335a0 X - X X X X X X
brcm,bcm4349-bt X - X X X X X X
infineon,cyw55572-bt X - X X X X X X
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
CYW55572 is a Wi-Fi + Bluetooth combo device from Infineon.
Extend the binding with its DT compatible.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The BCM4349B1, aka CYW/BCM89359, is a WiFi+BT chip and its Bluetooth
portion can be controlled over serial.
Extend the binding with its DT compatible.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add property, "brcm,requires-autobaud-mode", to enable autobaud mode
selection.
Some devices (e.g. CYW5557x) require autobaud mode to enable FW loading.
Autobaud mode can also be required on some boards where the controller
device is using a non-standard baud rate when first powered on.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add CAN binding documentation for Renesas RZ/N1 SoC.
The SJA1000 CAN controller on RZ/N1 SoC has some differences compared
to others like it has no clock divider register (CDR) support and it has
no HW loopback (HW doesn't see tx messages on rx), so introduced a new
compatible 'renesas,rzn1-sja1000' to handle these differences.
Link: https://lore.kernel.org/all/20220710115248.190280-3-biju.das.jz@bp.renesas.com
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Convert the NXP SJA1000 CAN Controller Device Tree binding
documentation to json-schema.
Update the example to match reality.
Link: https://lore.kernel.org/all/20220710115248.190280-2-biju.das.jz@bp.renesas.com
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Most of the contents are bugfixes for the devicetree files:
- A Qualcomm MSM8974 pin controller regression, caused by a cleanup
patch that gets partially reverted here.
- Missing properties for Broadcom BCM49xx to fix timer detection and
SMP boot.
- Fix touchscreen pinctrl for imx6ull-colibri board
- Multiple fixes for Rockchip rk3399 based machines including the vdu
clock-rate fix, otg port fix on Quartz64-A and ethernet on
Quartz64-B
- Fixes for misspelled DT contents causing minor problems on
imx6qdl-ts7970m, orangepi-zero, sama5d2, kontron-kswitch-d10, and
ls1028a
And a couple of changes elsewhere:
- Fix binding for Allwinner D1 display pipeline
- Trivial code fixes to the TEE and reset controller driver
subsystems and the rockchip platform code.
- Multiple updates to the MAINTAINERS files, marking the Palm Treo
support as orphaned, and fixing some entries for added or changed
file names"
* tag 'soc-fixes-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (21 commits)
arm64: dts: broadcom: bcm4908: Fix cpu node for smp boot
arm64: dts: broadcom: bcm4908: Fix timer node for BCM4906 SoC
ARM: dts: sunxi: Fix SPI NOR campatible on Orange Pi Zero
ARM: dts: at91: sama5d2: Fix typo in i2s1 node
tee: tee_get_drvdata(): fix description of return value
optee: Remove duplicate 'of' in two places.
ARM: dts: kswitch-d10: use open drain mode for coma-mode pins
ARM: dts: colibri-imx6ull: fix snvs pinmux group
optee: smc_abi.c: fix wrong pointer passed to IS_ERR/PTR_ERR()
MAINTAINERS: add polarfire rng, pci and clock drivers
MAINTAINERS: mark ARM/PALM TREO SUPPORT orphan
ARM: dts: imx6qdl-ts7970: Fix ngpio typo and count
arm64: dts: ls1028a: Update SFP node to include clock
dt-bindings: display: sun4i: Fix D1 pipeline count
ARM: dts: qcom: msm8974: re-add missing pinctrl
reset: Fix devm bulk optional exclusive control getter
MAINTAINERS: rectify entry for SYNOPSYS AXS10x RESET CONTROLLER DRIVER
ARM: rockchip: Add missing of_node_put() in rockchip_suspend_init()
arm64: dts: rockchip: Assign RK3399 VDU clock rate
arm64: dts: rockchip: Fix Quartz64-A dwc3 otg port behavior
...
|
|
include/net/sock.h
310731e2f161 ("net: Fix data-races around sysctl_mem.")
e70f3c701276 ("Revert "net: set SK_MEM_QUANTUM to 4096"")
https://lore.kernel.org/all/20220711120211.7c8b7cba@canb.auug.org.au/
net/ipv4/fib_semantics.c
747c14307214 ("ip: fix dflt addr selection for connected nexthop")
d62607c3fe45 ("net: rename reference+tracking helpers")
net/tls/tls.h
include/net/tls.h
3d8c51b25a23 ("net/tls: Check for errors in tls_device_init")
587903142308 ("tls: create an internal header")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, bpf and wireless.
Still no major regressions, the release continues to be calm. An
uptick of fixes this time around due to trivial data race fixes and
patches flowing down from subtrees.
There has been a few driver fixes (particularly a few fixes for false
positives due to 66e4c8d95008 which went into -next in May!) that make
me worry the wide testing is not exactly fully through.
So "calm" but not "let's just cut the final ASAP" vibes over here.
Current release - regressions:
- wifi: rtw88: fix write to const table of channel parameters
Current release - new code bugs:
- mac80211: add gfp_t arg to ieeee80211_obss_color_collision_notify
- mlx5:
- TC, allow offload from uplink to other PF's VF
- Lag, decouple FDB selection and shared FDB
- Lag, correct get the port select mode str
- bnxt_en: fix and simplify XDP transmit path
- r8152: fix accessing unset transport header
Previous releases - regressions:
- conntrack: fix crash due to confirmed bit load reordering (after
atomic -> refcount conversion)
- stmmac: dwc-qos: disable split header for Tegra194
Previous releases - always broken:
- mlx5e: ring the TX doorbell on DMA errors
- bpf: make sure mac_header was set before using it
- mac80211: do not wake queues on a vif that is being stopped
- mac80211: fix queue selection for mesh/OCB interfaces
- ip: fix dflt addr selection for connected nexthop
- seg6: fix skb checksums for SRH encapsulation/insertion
- xdp: fix spurious packet loss in generic XDP TX path
- bunch of sysctl data race fixes
- nf_log: incorrect offset to network header
Misc:
- bpf: add flags arg to bpf_dynptr_read and bpf_dynptr_write APIs"
* tag 'net-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
nfp: flower: configure tunnel neighbour on cmsg rx
net/tls: Check for errors in tls_device_init
MAINTAINERS: Add an additional maintainer to the AMD XGBE driver
xen/netback: avoid entering xenvif_rx_next_skb() with an empty rx queue
selftests/net: test nexthop without gw
ip: fix dflt addr selection for connected nexthop
net: atlantic: remove aq_nic_deinit() when resume
net: atlantic: remove deep parameter on suspend/resume functions
sfc: fix kernel panic when creating VF
seg6: bpf: fix skb checksum in bpf_push_seg6_encap()
seg6: fix skb checksum in SRv6 End.B6 and End.B6.Encaps behaviors
seg6: fix skb checksum evaluation in SRH encapsulation/insertion
sfc: fix use after free when disabling sriov
net: sunhme: output link status with a single print.
r8152: fix accessing unset transport header
net: stmmac: fix leaks in probe
net: ftgmac100: Hold reference returned by of_get_child_by_name()
nexthop: Fix data-races around nexthop_compat_mode.
ipv4: Fix data-races around sysctl_ip_dynaddr.
tcp: Fix a data-race around sysctl_tcp_ecn_fallback.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Hopefully the last one for 5.19. This became bigger than wished, but
all changes are pretty device-specific small fixes, which look less
worrisome.
The majority of changes are about various ASoC fixes, while the usual
HD-audio quirks are included as well"
* tag 'sound-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (28 commits)
ALSA: hda/realtek - Enable the headset-mic on a Xiaomi's laptop
ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc221
ALSA: hda/realtek: fix mute/micmute LEDs for HP machines
ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc671
ALSA: hda - Add fixup for Dell Latitidue E5430
ALSA: hda/conexant: Apply quirk for another HP ProDesk 600 G3 model
ALSA: hda/realtek: Fix headset mic for Acer SF313-51
ASoC: Intel: Skylake: Correct the handling of fmt_config flexible array
ASoC: Intel: Skylake: Correct the ssp rate discovery in skl_get_ssp_clks()
ASoC: rt5640: Fix the wrong state of JD1 and JD2
ASoC: Intel: sof_rt5682: fix out-of-bounds array access
ASoC: qdsp6: fix potential memory leak in q6apm_get_audioreach_graph()
ASoC: tas2764: Fix amp gain register offset & default
ASoC: tas2764: Correct playback volume range
ASoC: tas2764: Fix and extend FSYNC polarity handling
ASoC: tas2764: Add post reset delays
ASoC: dt-bindings: Fix description for msm8916
ASoC: doc: Capitalize RESET line name
ASoC: arizona: Update arizona_aif_cfg_changed to use RX_BCLK_RATE
ASoC: cs47l92: Fix event generation for OUT1 demux
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
A small set of fixes for
* queue selection in mesh/ocb
* queue handling on interface stop
* hwsim virtio device vs. some other virtio changes
* dt-bindings email addresses
* color collision memory allocation
* a const variable in rtw88
* shared SKB transmit in the ethernet format path
* P2P client port authorization
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename the dt nodes shown in the sff,sfp.yaml examples so that they are
generic and not really tied to a specific platform.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert the sff,sfp.txt bindings to the DT schema format.
Also add the new path to the list of maintained files.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
"One core fix for DMA_INTERRUPT and rest driver fixes.
Core:
- Revert verification of DMA_INTERRUPT capability as that was
incorrect
Bunch of driver fixes for:
- ti: refcount and put_device leak
- qcom_bam: runtime pm overflow
- idxd: force wq context cleanup and call idxd_enable_system_pasid()
on success
- dw-axi-dmac: RMW on channel suspend register
- imx-sdma: restart cyclic channel when enabled
- at_xdma: error handling for at_xdmac_alloc_desc
- pl330: lockdep warning
- lgm: error handling path in probe
- allwinner: Fix min/max typo in binding"
* tag 'dmaengine-fix-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dt-bindings: dma: allwinner,sun50i-a64-dma: Fix min/max typo
dmaengine: lgm: Fix an error handling path in intel_ldma_probe()
dmaengine: pl330: Fix lockdep warning about non-static key
dmaengine: idxd: Only call idxd_enable_system_pasid() if succeeded in enabling SVA feature
dmaengine: at_xdma: handle errors of at_xdmac_alloc_desc() correctly
dmaengine: imx-sdma: only restart cyclic channel when enabled
dmaengine: dw-axi-dmac: Fix RMW on channel suspend register
dmaengine: idxd: force wq context cleanup on device disable path
dmaengine: qcom: bam_dma: fix runtime PM underflow
dmaengine: imx-sdma: Allow imx8m for imx7 FW revs
dmaengine: Revert "dmaengine: add verification of DMA_INTERRUPT capability for dmatest"
dmaengine: ti: Add missing put_device in ti_dra7_xbar_route_allocate
dmaengine: ti: Fix refcount leak in ti_dra7_xbar_route_allocate
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
- fix binding for D1 display pipeline
* tag 'sunxi-fixes-for-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
dt-bindings: display: sun4i: Fix D1 pipeline count
Link: https://lore.kernel.org/r/YshiPKZRq6NHxPzO@kista.localdomain
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Until now the PolarFire SoC (MPFS) has been using the generic
"cdns,macb" compatible but has optional reset support. Add a specific
compatible which falls back to the currently used generic binding.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For the existing msm8916 bindings the minimum reg/reg-names is 1 not 2.
Similarly the minimum interrupt/interrupt-names is 1 not 2.
Fixes: f3fc4fbfa2d2 ("ASoC: dt-bindings: Add SC7280 lpass cpu bindings")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220629114012.3282945-1-bryan.odonoghue@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The conditional block for variants with a second clock should have set
minItems, not maxItems, which was already 2. Since clock-names requires
two items, this typo should not have caused any problems.
Fixes: edd14218bd66 ("dt-bindings: dmaengine: Convert Allwinner A31 and A64 DMA to a schema")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220702031903.21703-1-samuel@sholland.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The 'reg' property is missing from the mediatek,mt7530 schema which
results in the following warning once 'unevaluatedProperties' is fixed:
Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.example.dtb: switch@0: Unevaluated properties are not allowed ('reg' was unexpected)
Fixes: e0dda3119741 ("dt-bindings: net: dsa: convert binding for mediatek switches")
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220701222240.1706272-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When adding the bindings for the D1 display engine, I missed the
condition for the number of pipelines. D1 has two mixers, so it
will have two pipeline references.
Fixes: ae5a5d26c15c ("dt-bindings: display: Add D1 display engine compatibles")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220702032921.22433-1-samuel@sholland.org
|
|
Describe the switch interrupts (dlr, switch, prp, hub, pattern) which
are connected to the GIC.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Documentation in .yaml format and updates to the MAINTAINERS
Also 'make dt_binding_check' is passed.
RGMII internal delay values for the mac is retrieved from
rx-internal-delay-ps & tx-internal-delay-ps as per the feedback from
v3 patch series.
https://lore.kernel.org/netdev/20210802121550.gqgbipqdvp5x76ii@skbuf/
It supports only the delay value of 0ns and 2ns.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
*-internal-delay-ps properties would be applicable only for RGMII interface
modes.
It is changed as per the request.
Ran dt_binding_check to confirm nothing is broken.
link: https://lore.kernel.org/netdev/d8e5f6a8-a7e1-dabd-f4b4-ea8ea21d0a1d@gmail.com/
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable led-mode configuration for LAN8814 phy
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c
9c5de246c1db ("net: sparx5: mdb add/del handle non-sparx5 devices")
fbb89d02e33a ("net: sparx5: Allow mdb entries to both CPU and ports")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add description for new properties which will be parsed in driver.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add binding document for Ethernet on MT8365.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Reviewed-by: Bartosz Golaszewski <brgl@bgdev.pl>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-06-25
this is a pull request of 22 patches for net-next/master.
The first 2 patches target the xilinx driver. Srinivas Neeli's patch
adds Transmitter Delay Compensation (TDC) support, a patch by me fixes
a typo.
The next patch is by me and fixes a typo in the m_can driver.
Another patch by me allows the configuration of fixed bit rates
without need for do_set_bittiming callback.
The following 7 patches are by Vincent Mailhol and refactor the
can-dev module and Kbuild, de-inline the can_dropped_invalid_skb()
function, which has grown over the time, and drop outgoing skbs if the
controller is in listen only mode.
Max Staudt's patch fixes a reference in the networking/can.rst
documentation.
Vincent Mailhol provides 2 patches with cleanups for the etas_es58x
driver.
Conor Dooley adds bindings for the mpfs-can to the PolarFire SoC dtsi.
Another patch by me allows the configuration of fixed data bit rates
without need for do_set_data_bittiming callback.
The last 5 patches are by Frank Jungclaus. They prepare the esd_usb
driver to add support for the the CAN-USB/3 device in a later series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add "renesas,rzn1-gmac" and "renesas,r9a06g032-gmac" compatible strings.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the stmmac driver already uses pm_runtime*() functions, describe
"power-domains" property in the binding.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add bindings for Renesas RZ/N1 Advanced 5 port switch. This switch is
present on Renesas RZ/N1 SoC and was probably provided by MoreThanIP.
This company does not exists anymore and has been bought by Synopsys.
Since this IP can't be find anymore in the Synospsy portfolio, lets use
Renesas as the vendor compatible for this IP.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This MII converter can be found on the RZ/N1 processor family. The MII
converter ports are declared as subnodes which are then referenced by
users of the PCS driver such as the switch.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are some small USB driver fixes and new device ids for 5.19-rc4
for a few small reported issues. They include:
- new usb-serial driver ids
- MAINTAINERS file update to properly catch the USB dts files
- dt-bindings fixes for reported build warnings
- xhci driver fixes for reported problems
- typec Kconfig dependancy fix
- raw_gadget fuzzing fixes found by syzbot
- chipidea driver bugfix
- usb gadget uvc bugfix
All of these have been in linux-next with no reported issues"
* tag 'usb-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: chipidea: udc: check request status before setting device address
USB: gadget: Fix double-free bug in raw_gadget driver
xhci-pci: Allow host runtime PM as default for Intel Meteor Lake xHCI
xhci-pci: Allow host runtime PM as default for Intel Raptor Lake xHCI
xhci: turn off port power in shutdown
xhci: Keep interrupt disabled in initialization until host is running.
USB: serial: option: add Quectel RM500K module support
USB: serial: option: add Quectel EM05-G modem
USB: serial: pl2303: add support for more HXN (G) types
usb: typec: wcove: Drop wrong dependency to INTEL_SOC_PMIC
usb: gadget: uvc: fix list double add in uvcg_video_pump
dt-bindings: usb: ehci: Increase the number of PHYs
dt-bindings: usb: ohci: Increase the number of PHYs
usb: gadget: Fix non-unique driver names in raw-gadget driver
MAINTAINERS: add include/dt-bindings/usb to USB SUBSYSTEM
USB: serial: option: add Telit LE910Cx 0x1250 composition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A bunch of driver specific fixes, plus a fix for spi-mem's status
polling for devices that use GPIO chip selects and a DT bindings
examples fix that helps with the validation work"
* tag 'spi-fix-v5.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: rockchip: Unmask IRQ at the final to avoid preemption
spi: dt-bindings: Fix unevaluatedProperties warnings in examples
spi: spi-mem: Fix spi_mem_poll_status()
spi: cadence: Detect transmit FIFO depth
spi: spi-cadence: Fix SPI CS gets toggling sporadically
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
"make dtbs_check":
arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee080100: phys: [[17, 0], [31]] is too long
From schema: Documentation/devicetree/bindings/usb/generic-ehci.yaml
arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee0c0100: phys: [[17, 1], [33], [21, 0]] is too long
From schema: Documentation/devicetree/bindings/usb/generic-ehci.yaml
Some USB EHCI controllers (e.g. on the Renesas RZ/G1C SoC) have multiple
PHYs. Increase the maximum number of PHYs to 3, which is sufficient for
now.
Fixes: 0499220d6dadafa5 ("dt-bindings: Add missing array size constraints")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/c5d19e2f9714f43effd90208798fc1936098078f.1655301043.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
"make dtbs_check":
arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee080000: phys: [[17, 0], [31]] is too long
From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee0c0000: phys: [[17, 1], [33], [21, 0]] is too long
From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
Some USB OHCI controllers (e.g. on the Renesas RZ/G1C SoC) have multiple
PHYs. Increase the maximum number of PHYs to 3, which is sufficient for
now.
Fixes: 0499220d6dadafa5 ("dt-bindings: Add missing array size constraints")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/0112f9c8881513cb33bf7b66bc743dd08b35a2f5.1655301203.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of interrupt subsystem updates:
Core:
- Ensure runtime power management for chained interrupts
Drivers:
- A collection of OF node refcount fixes
- Unbreak MIPS uniprocessor builds
- Fix xilinx interrupt controller Kconfig dependencies
- Add a missing compatible string to the Uniphier driver"
* tag 'irq-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/loongson-liointc: Use architecture register to get coreid
irqchip/uniphier-aidet: Add compatible string for NX1 SoC
dt-bindings: interrupt-controller/uniphier-aidet: Add bindings for NX1 SoC
irqchip/realtek-rtl: Fix refcount leak in map_interrupts
irqchip/gic-v3: Fix refcount leak in gic_populate_ppi_partitions
irqchip/gic-v3: Fix error handling in gic_populate_ppi_partitions
irqchip/apple-aic: Fix refcount leak in aic_of_ic_init
irqchip/apple-aic: Fix refcount leak in build_fiq_affinity
irqchip/gic/realview: Fix refcount leak in realview_gic_of_init
irqchip/xilinx: Remove microblaze+zynq dependency
genirq: PM: Use runtime PM for chained interrupts
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Add missing lock protection in occ driver
- Add missing comma in board name list in asus-ec-sensors driver
- Fix devicetree bindings for ti,tmp401
* tag 'hwmon-for-v5.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (asus-ec-sensors) add missing comma in board name list.
hwmon: (occ) Lock mutex in shutdown to prevent race with occ_active
dt-bindings: hwmon: ti,tmp401: Drop 'items' from 'ti,n-factor' property
|
|
We have a board where measurements indicate that the current three
options - leaving IO_IMPEDANCE_CTRL at the reset value (which is
factory calibrated to a value corresponding to approximately 50 ohms)
or using one of the two boolean properties to set it to the min/max
value - are too coarse.
There is no fixed mapping from register values to values in the range
35-70 ohms; it varies from chip to chip, and even that target range is
approximate. So add a DT binding for an nvmem cell which can be
populated during production with a value suitable for each specific
board.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
My codeaurora.org email doesn't work anymore, so switch to my preferred
kernel.org address.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610133640.10810-2-kvalo@kernel.org
|
|
Toke now maintains ath9k so update DT bindings as well.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610133640.10810-1-kvalo@kernel.org
|
|
Add basic description for the xilinx emaclite driver DT bindings.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A board may have no independent reset-line, so reset cannot be used
inside switch driver.
E.g. on Bananapi-R2 Pro switch and gmac are connected to same reset-line.
Resets should be acquired only to 1 device/driver. This prevents reset to
be bound to switch-driver if reset is already used for gmac. If reset is
only used by switch driver it resets the switch *and* the gmac after the
mdio bus comes up resulting in mdio bus goes down. It takes some time
until all is up again, switch driver tries to read from mdio, will fail
and defer the probe. On next try the reset does the same again.
Make reset optional for such boards.
Allow port 5 as cpu-port and phy-mode rgmii for mt7531.
- MT7530 supports RGMII on port 5 and RGMII/TRGMII on port 6.
- MT7531 supports on port 5 RGMII and SGMII (dual-sgmii) and
SGMII on port 6.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert txt binding to yaml binding for Mediatek switches.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a binding for the CAN controller on PolarFire SoC (MPFS).
A data sheet and a register map can be downloaded at:
| https://www.microsemi.com/document-portal/doc_download/1245725-polarfire-soc-fpga-mss-technical-reference-manual
| https://www.microsemi.com/document-portal/doc_download/1244581-polarfire-soc-register-map
An alternative location for the register map is:
| http://web.archive.org/web/20220403030214/https://www.microsemi.com/document-portal/doc_download/1244581-polarfire-soc-register-map
Link: https://lore.kernel.org/all/20220607065459.2035746-2-conor.dooley@microchip.com
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[mkl: add link to data sheet and register map]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull more devicetree fixes from Rob Herring:
- More DT meta-schema check fixes from new bindings in merge window
- Fix stale DT binding references from Mauro
- Update various binding maintainers
- Fix in arm,malidp properties to match reality
- Add deprecated 'atheros' vendor prefix
* tag 'devicetree-fixes-for-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: display: arm,malidp: remove bogus RQOS property
dt-bindings: pinctrl: ralink: Fix 'enum' lists with duplicate entries
dt-bindings: Drop more redundant 'maxItems/minItems' in if/then schemas
dt-bindings: nvme: apple,nvme-ans: Drop 'maxItems' from 'apple,sart'
MAINTAINERS: rectify entries for ARM DRM DRIVERS after dt conversion
MAINTAINERS: update snps,axs10x-reset.yaml reference
MAINTAINERS: update dongwoon,dw9807-vcm.yaml reference
MAINTAINERS: update cortina,gemini-ethernet.yaml reference
dt-bindings: mfd: rk808: update rockchip,rk808.yaml reference
dt-bindings: reset: update st,stih407-powerdown.yaml references
dt-bindings: arm: update vexpress-config.yaml references
dt-bindings: interrupt-controller: update brcm,l2-intc.yaml reference
dt-bindings: mfd: bd9571mwv: update rohm,bd9571mwv.yaml reference
dt-bindings: update Luca Ceresoli's e-mail address
dt-bindings: msm: update maintainers list with proper id
dt-bindings: vendor-prefixes: document deprecated Atheros
dt-bindings: Update QCOM USB subsystem maintainer information
|
|
As Liviu pointed out, the arm,malidp-arqos-high-level property
mentioned in the original .txt binding was a mistake, and
arm,malidp-arqos-value needs to take its place.
The binding commit ce6eb0253cba ("dt/bindings: display: Add optional
property node define for Mali DP500") mentions the right name in the
commit message, but has the wrong name in the diff.
Commit d298e6a27a81 ("drm/arm/mali-dp: Add display QoS interface
configuration for Mali DP500") uses the property in the driver, but uses
the shorter name.
Remove the wrong property from the binding, and use the proper name in
the example. The actual property was already documented properly.
Fixes: 2c8b082a3ab1 ("dt-bindings: display: convert Arm Mali-DP to DT schema")
Link: https://lore.kernel.org/linux-arm-kernel/YnumGEilUblhBx8E@e110455-lin.cambridge.arm.com/
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220609162729.1441760-1-andre.przywara@arm.com
|
|
There's no reason to list the same value twice in an 'enum'. This was fixed
treewide in commit c3b006819426 ("dt-bindings: Fix 'enum' lists with
duplicate entries"), but this one got added in the merge window.
A meta-schema change will catch future cases.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20220606212239.1360877-1-robh@kernel.org
|