| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Drop the RCPM consumer example from the binding (LPUART device node),
because:
1. Using phandles is typical syntax, thus explaining it is not needed in
the provider binding,
2. It has 'fsl,rcpm-wakeup' property which is not allowed by LPUART
binding so it causes dt_binding_check warning:
fsl,rcpm.example.dtb: serial@2950000: Unevaluated properties are not allowed ('fsl,rcpm-wakeup' was unexpected)
from schema $id: http://devicetree.org/schemas/serial/fsl-lpuart.yaml#
Alternatively, this property could be added to LPUART binding
(fsl-lpuart.yaml), but it looks like none of in-tree DTS use it.
Fixes: ad21e3840a88 ("dt-bindings: soc: fsl: Convert rcpm to yaml format")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240811153507.126512-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Document the "isl,isl69260" compatible, which is already used in the
DTS files but was not previously documented in the bindings.
The ISL69260 is a digital dual output multiphase controller
that supports Intel VR13, VR13.HC, and VR14 specifications.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240809070056.3588694-1-peteryin.openbmc@gmail.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Add compatible string, fsl,ls1088a-isc, fsl,ls2080a-isc, fsl,lx2160a-isc.
Fix the below warning:
arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dtb: /soc/syscon@1f70000: failed to match any schema with compatible: ['fsl,ls2080a-isc', 'syscon']
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240806162121.2996442-1-Frank.Li@nxp.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Convert dt-binding rcpm from txt to yaml format.
Add fsl,ls1028a-rcpm compatible string.
Additional changes:
- Add missed compatible string fsl,<chip>-rcpm.
- Remove map fsl,<chip>-rcpm to fsl,qoriq-rcpm-<version>.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240802152219.2740137-1-Frank.Li@nxp.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Document TI TPS546D24 TPS546D24A 2.95-V to 16-V, 40-A, Up to 4x Stackable,
PMBus Buck Converter as trivial device. Linux kernel does have an existing
driver using the compatible documented here.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240725180337.64396-1-marex@denx.de
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Convert the bindings for the External Bus Interface on apq8060 and
msm8660 from the old text format to yaml.
Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240717131030.51419-1-rayyan.ansari@linaro.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull more devicetree updates from Rob Herring:
"Most of this is a treewide change to of_property_for_each_u32() which
was small enough to do in one go before rc1 and avoids the need to
create of_property_for_each_u32_some_new_name().
- Treewide conversion of of_property_for_each_u32() to drop internal
arguments making struct property opaque
- Add binding for Amlogic A4 SoC watchdog
- Fix constraints for AD7192 'single-channel' property"
* tag 'devicetree-fixes-for-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: iio: adc: ad7192: Fix 'single-channel' constraints
of: remove internal arguments from of_property_for_each_u32()
dt-bindings: watchdog: add support for Amlogic A4 SoCs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"The bulk of this is a series of fixes for the microchip-core driver
mostly originating from one of their customers, I also applied an
additional patch adding support for controlling the word size which
came along with it since it's still the merge window and clearly had a
bunch of fairly thorough testing.
We also have a fix for the compatible used to bind spidev to the
BH2228FV"
* tag 'spi-fix-v6.11-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spidev: add correct compatible for Rohm BH2228FV
dt-bindings: trivial-devices: fix Rohm BH2228FV compatible string
spi: microchip-core: add support for word sizes of 1 to 32 bits
spi: microchip-core: ensure TX and RX FIFOs are empty at start of a transfer
spi: microchip-core: fix init function not setting the master and motorola modes
spi: microchip-core: only disable SPI controller when register value change requires it
spi: microchip-core: defer asserting chip select until just before write to TX FIFO
spi: microchip-core: fix the issues in the isr
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"This cycle, there are new features for the Designware controller and
fixes for the other IPs:
- dw: optional apb clock and power management support, IBI handling
fixes
- mipi-i3c-hci: IBI handling fixes
- svc: a few fixes"
* tag 'i3c/for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
dt-bindings: i3c: add header for generic I3C flags
i3c: master: svc: Fix error code in svc_i3c_master_do_daa_locked()
i3c: master: Enhance i3c_bus_type visibility for device searching & event monitoring
i3c: dw: Add power management support
i3c: dw: Add some functions for reusability
i3c: dw: Save timing registers and other values
i3c: master: svc: Improve DAA STOP handle code logic
i3c: dw: Add optional apb clock
i3c: dw: Use new *_enabled clk API
dt-bindings: i3c: dw: Add apb clock binding
i3c: master: svc: Convert comma to semicolon
i3c: mipi-i3c-hci: Round IBI data chunk size to HW supported value
i3c: mipi-i3c-hci: Error out instead on BUG_ON() in IBI DMA setup
i3c: mipi-i3c-hci: Set IBI Status and Data Ring base addresses
i3c: mipi-i3c-hci: Switch to lower_32_bits()/upper_32_bits() helpers
i3c: dw: Remove ibi_capable property
i3c: dw: Fix IBI intr programming
i3c: dw: Fix clearing queue thld
i3c: mipi-i3c-hci: Fix number of DAT/DCT entries for HCI versions < 1.1
i3c: master: svc: resend target address when get NACK
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc hotfixes from Andrew Morton:
"11 hotfixes, 7 of which are cc:stable. 7 are MM, 4 are other"
* tag 'mm-hotfixes-stable-2024-07-26-14-33' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
nilfs2: handle inconsistent state in nilfs_btnode_create_block()
selftests/mm: skip test for non-LPA2 and non-LVA systems
mm/page_alloc: fix pcp->count race between drain_pages_zone() vs __rmqueue_pcplist()
mm: memcg: add cacheline padding after lruvec in mem_cgroup_per_node
alloc_tag: outline and export free_reserved_page()
decompress_bunzip2: fix rare decompression failure
mm/huge_memory: avoid PMD-size page cache if needed
mm: huge_memory: use !CONFIG_64BIT to relax huge page alignment on 32 bit machines
mm: fix old/young bit handling in the faulting path
dt-bindings: arm: update James Clark's email address
MAINTAINERS: mailmap: update James Clark's email address
|
|
My new address is james.clark@linaro.org
Link: https://lkml.kernel.org/r/20240709102512.31212-3-james.clark@linaro.org
Signed-off-by: James Clark <james.clark@linaro.org>
Cc: Bjorn Andersson <quic_bjorande@quicinc.com>
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Geliang Tang <geliang@kernel.org>
Cc: Hao Zhang <quic_hazha@quicinc.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Kees Cook <kees@kernel.org>
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Cc: Mao Jinlong <quic_jinlmao@quicinc.com>
Cc: Matthieu Baerts <matttbe@kernel.org>
Cc: Matt Ranostay <matt@ranostay.sg>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Rob Herring (Arm) <robh@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The 'single-channel' property is an uint32, not an array, so 'items' is
an incorrect constraint. This didn't matter until dtschema recently
changed how properties are decoded. This results in this warning:
Documentation/devicetree/bindings/iio/adc/adi,ad7192.example.dtb: adc@0: \
channel@1:single-channel: 1 is not of type 'array'
Fixes: caf7b7632b8d ("dt-bindings: iio: adc: ad7192: Add AD7194 support")
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240723230904.1299744-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Pull drm fixes from Dave Airlie:
"Fixes for rc1, mostly amdgpu, i915 and xe, with some other misc ones,
doesn't seem to be anything too serious.
amdgpu:
- Bump driver version for GFX12 DCC
- DC documention warning fixes
- VCN unified queue power fix
- SMU fix
- RAS fix
- Display corruption fix
- SDMA 5.2 workaround
- GFX12 fixes
- Uninitialized variable fix
- VCN/JPEG 4.0.3 fixes
- Misc display fixes
- RAS fixes
- VCN4/5 harvest fix
- GPU reset fix
i915:
- Reset intel_dp->link_trained before retraining the link
- Don't switch the LTTPR mode on an active link
- Do not consider preemption during execlists_dequeue for gen8
- Allow NULL memory region
xe:
- xe_exec ioctl minor fix on sync entry cleanup upon error
- SRIOV: limit VF LMEM provisioning
- Wedge mode fixes
v3d:
- fix indirect dispatch on newer v3d revs
panel:
- fix panel backlight bindings"
* tag 'drm-next-2024-07-26' of https://gitlab.freedesktop.org/drm/kernel: (39 commits)
drm/amdgpu: reset vm state machine after gpu reset(vram lost)
drm/amdgpu: add missed harvest check for VCN IP v4/v5
drm/amdgpu: Fix eeprom max record count
drm/amdgpu: fix ras UE error injection failure issue
drm/amd/display: Remove ASSERT if significance is zero in math_ceil2
drm/amd/display: Check for NULL pointer
drm/amdgpu/vcn: Use offsets local to VCN/JPEG in VF
drm/amdgpu: Add empty HDP flush function to VCN v4.0.3
drm/amdgpu: Add empty HDP flush function to JPEG v4.0.3
drm/amd/amdgpu: Fix uninitialized variable warnings
drm/amdgpu: Fix atomics on GFX12
drm/amdgpu/sdma5.2: Update wptr registers as well as doorbell
drm/i915: Allow NULL memory region
drm/i915/gt: Do not consider preemption during execlists_dequeue for gen8
dt-bindings: display: panel: samsung,atna33xc20: Document ATNA45AF01
drm/xe: Don't suspend device upon wedge
drm/xe: Wedge the entire device
drm/xe/pf: Limit fair VF LMEM provisioning
drm/xe/exec: Fix minor bug related to xe_sync_entry_cleanup
drm/amd/display: fix corruption with high refresh rates on DCN 3.0
...
|
|
Add header file for generic I3C flags to avoid hard code in dts file.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240715225351.3237284-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add dt binding for optional apb clock. Core clock is mandatory.
Signed-off-by: Aniket <aniketmaurya@google.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240628154526.324068-1-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-next
A single fix for a panel compatible
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240725-frisky-wren-of-tact-f5f504@houat
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- make watchdog_class const
- rework of the rzg2l_wdt driver
- other small fixes and improvements
* tag 'linux-watchdog-6.11-rc1' of git://www.linux-watchdog.org/linux-watchdog:
dt-bindings: watchdog: dlg,da9062-watchdog: Drop blank space
watchdog: rzn1: Convert comma to semicolon
watchdog: lenovo_se10_wdt: Convert comma to semicolon
dt-bindings: watchdog: renesas,wdt: Document RZ/G3S support
watchdog: rzg2l_wdt: Add suspend/resume support
watchdog: rzg2l_wdt: Rely on the reset driver for doing proper reset
watchdog: rzg2l_wdt: Remove comparison with zero
watchdog: rzg2l_wdt: Remove reset de-assert from probe
watchdog: rzg2l_wdt: Check return status of pm_runtime_put()
watchdog: rzg2l_wdt: Use pm_runtime_resume_and_get()
watchdog: rzg2l_wdt: Make the driver depend on PM
watchdog: rzg2l_wdt: Restrict the driver to ARCH_RZG2L and ARCH_R9A09G011
watchdog: imx7ulp_wdt: keep already running watchdog enabled
watchdog: starfive: Add missing clk_disable_unprepare()
watchdog: Make watchdog_class const
|
|
Update dt-binding document for watchdog of Amlogic A4 SoCs.
Signed-off-by: Huqiang Qin <huqiang.qin@amlogic.com>
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240709-a4-a5_watchdog-v1-1-2ae852e05ec2@amlogic.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New Support
- Samsung Exynos gs101 drd combo phy
- Qualcomm SC8180x USB uniphy, IPQ9574 QMP PCIe phy
- Airoha EN7581 PCIe phy
- Freescale i.MX8Q HSIO SerDes phy
- Starfive jh7110 dphy tx
Updates:
- Resume support for j721e-wiz driver
- Updates to Exynos usbdrd driver
- Support for optional power domains in g12a usb2-phy driver
- Debugfs support and updates to zynqmp driver"
* tag 'phy-for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (56 commits)
phy: airoha: Add dtime and Rx AEQ IO registers
dt-bindings: phy: airoha: Add dtime and Rx AEQ IO registers
dt-bindings: phy: rockchip-emmc-phy: Convert to dtschema
dt-bindings: phy: qcom,qmp-usb: fix spelling error
phy: exynos5-usbdrd: support Exynos USBDRD 3.1 combo phy (HS & SS)
phy: exynos5-usbdrd: convert Vbus supplies to regulator_bulk
phy: exynos5-usbdrd: convert (phy) register access clock to clk_bulk
phy: exynos5-usbdrd: convert core clocks to clk_bulk
phy: exynos5-usbdrd: support isolating HS and SS ports independently
dt-bindings: phy: samsung,usb3-drd-phy: add gs101 compatible
phy: core: Fix documentation of of_phy_get
phy: starfive: Correct the dphy configure process
phy: zynqmp: Add debugfs support
phy: zynqmp: Take the phy mutex in xlate
phy: zynqmp: Only wait for PLL lock "primary" instances
phy: zynqmp: Store instance instead of type
phy: zynqmp: Enable reference clock correctly
phy: cadence-torrent: Check return value on register read
phy: Fix the cacography in phy-exynos5250-usb2.c
phy: phy-rockchip-samsung-hdptx: Select CONFIG_MFD_SYSCON
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New support:
- New dmaengine_prep_peripheral_dma_vec() to support transfers using
dma vectors and documentation and user in AXI dma
- STMicro STM32 DMA3 support and new capabilities of cyclic dma
Updates:
- Yaml conversion for Freescale imx dma and qdma bindings,
sprd sc9860 dma binding
- Altera msgdma updates for descriptor management"
* tag 'dmaengine-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (35 commits)
dt-bindings: fsl-qdma: fix interrupts 'if' check logic
dt-bindings: dma: sprd,sc9860-dma: convert to YAML
dmaengine: fsl-dpaa2-qdma: add missing MODULE_DESCRIPTION() macro
dmaengine: ti: add missing MODULE_DESCRIPTION() macros
dmaengine: ti: cppi41: add missing MODULE_DESCRIPTION() macro
dmaengine: virt-dma: add missing MODULE_DESCRIPTION() macro
dmaengine: ti: k3-udma: Fix BCHAN count with UHC and HC channels
dmaengine: sh: rz-dmac: Fix lockdep assert warning
dmaengine: qcom: gpi: clean up the IRQ disable/enable in gpi_reset_chan()
dmaengine: fsl-edma: change the memory access from local into remote mode in i.MX 8QM
dmaengine: qcom: gpi: remove unused struct 'reg_info'
dmaengine: moxart-dma: remove unused struct 'moxart_filter_data'
dt-bindings: fsl-qdma: Convert to yaml format
dmaengine: fsl-edma: remove redundant "idle" field from fsl_chan
dmaengine: fsl-edma: request per-channel IRQ only when channel is allocated
dmaengine: stm32-dma3: defer channel registration to specify channel name
dmaengine: add channel device name to channel registration
dmaengine: stm32-dma3: improve residue granularity
dmaengine: stm32-dma3: add device_pause and device_resume ops
dmaengine: stm32-dma3: add DMA_MEMCPY capability
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull remoteproc updates from Bjorn Andersson:
- The maximum amount of DDR memory used by the Mediatek MT8188/MT8195
SCP is increased to handle new use cases. Handling of optional L1TCM
memory is made actually optional.
- An optimization is introduced to only clear the unused portion of IPI
shared buffers, rather than the entire buffer before writing the
message.
- Detection for IPC-only mode in the TI K3 DSP remoteproc driver is
corrected. The loglevel of a debug print in the same is lowered from
error.
- Support for attaching to an running remote processor is added to the
Xilinx R5F.
- An in-kernel implementation of the Qualcomm "protected domain mapper"
(aka service registry) service is introduced, to remove the
dependency on a userspace implementation to detect when the battery
monitor and USB Type-C port manager becomes available. This is then
integrated with the Qualcomm remoteproc driver.
- The Qualcomm PAS remoteproc driver gains support for attempting to
bust hwspinlocks held by the remote processor when it
crashed/stopped.
- The TI OMAP remoteproc driver is transitioned to use devres helpers
for various forms of allocations.
- Parsing of memory-regions in the i.MX remoteproc driver is improved
to avoid a NULL pointer dereference if the phandle reference is
empty. of_node reference counting is corrected in the same.
* tag 'rproc-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
remoteproc: mediatek: Increase MT8188/MT8195 SCP core0 DRAM size
remoteproc: k3-dsp: Fix log levels where appropriate
remoteproc: xlnx: Add attach detach support
remoteproc: qcom: select AUXILIARY_BUS
remoteproc: k3-r5: Fix IPC-only mode detection
remoteproc: mediatek: Don't attempt to remap l1tcm memory if missing
remoteproc: qcom: enable in-kernel PD mapper
dt-bindings: remoteproc: imx_rproc: Add minItems for power-domain
remoteproc: imx_rproc: Fix refcount mistake in imx_rproc_addr_init
remoteproc: omap: Use devm_rproc_add() helper
remoteproc: omap: Use devm action to release reserved memory
remoteproc: omap: Use devm_rproc_alloc() helper
remoteproc: imx_rproc: Skip over memory region when node value is NULL
dt-bindings: remoteproc: k3-dsp: Correct optional sram properties for AM62A SoCs
remoteproc: qcom_q6v5_pas: Add hwspinlock bust on stop
soc: qcom: smem: Add qcom_smem_bust_hwspin_lock_by_host()
remoteproc: mediatek: Zero out only remaining bytes of IPI buffer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
"The I2C core has two header documentation updates as the dependecies
are in now.
The I2C host drivers add some patches which nearly fell through the
cracks:
- Added descriptions in the DTS for the Qualcomm SM8650 and SM8550
Camera Control Interface (CCI).
- Added support for the "settle-time-us" property, which allows the
gpio-mux device to switch from one bus to another with a
configurable delay. The time can be set in the DTS. The latest
change also includes file sorting.
- Fixed slot numbering in the SMBus framework to prevent failures
when more than 8 slots are occupied. It now enforces a a maximum of
8 slots to be used. This ensures that the Intel PIIX4 device can
register the SPDs correctly without failure, even if other slots
are populated but not used"
* tag 'i2c-for-6.11-rc1-second-batch' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: header: improve kdoc for i2c_algorithm
i2c: header: remove unneeded stuff regarding i2c_algorithm
i2c: piix4: Register SPDs
i2c: smbus: remove i801 assumptions from SPD probing
i2c: mux: gpio: Add support for the 'settle-time-us' property
i2c: mux: gpio: Re-order #include to match alphabetic order
dt-bindings: i2c: mux-gpio: Add 'settle-time-us' property
dt-bindings: i2c: qcom-cci: Document sm8650 compatible
dt-bindings: i2c: qcom-cci: Document sm8550 compatible
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox
Pull mailbox updates from Jassi Brar:
"broadcom:
- remove unused pdc_dma_map
imx:
- fix TXDB_V2 channel race condition
mediatek:
- cleanup and refactor driver
- add bindings for gce-props
omap:
- fix mailbox interrupt sharing
qcom:
- add bindings for SA8775p
- add CPUCP driver
zynqmp:
- make polling period configurable"
* tag 'mailbox-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox:
mailbox: mtk-cmdq: Move devm_mbox_controller_register() after devm_pm_runtime_enable()
mailbox: zynqmp-ipi: Make polling period configurable
mailbox: qcom-cpucp: fix 64BIT dependency
mailbox: Add support for QTI CPUCP mailbox controller
dt-bindings: mailbox: qcom: Add CPUCP mailbox controller bindings
dt-bindings: remoteproc: qcom,sa8775p-pas: Document the SA8775p ADSP, CDSP and GPDSP
mailbox: mtk-cmdq: add missing MODULE_DESCRIPTION() macro
mailbox: bcm-pdc: remove unused struct 'pdc_dma_map'
mailbox: imx: fix TXDB_V2 channel race condition
mailbox: omap: Fix mailbox interrupt sharing
mailbox: mtk-cmdq: Dynamically allocate clk_bulk_data structure
mailbox: mtk-cmdq: Move and partially refactor clocks probe
mailbox: mtk-cmdq: Stop requiring name for GCE clock
dt-bindings: mailbox: Add mediatek,gce-props.yaml
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- new charging_orange_full_green RGB LED trigger
- simplify and cleanup power-supply LED trigger code
- expose power information via hwmon compatibility layer
New hardware support:
- enable battery support for Qualcomm Snapdragon X Elite
- new battery driver for Maxim MAX17201/MAX17205
- new battery driver for Lenovo Yoga C630 laptop (custom EC)
Cleanups:
- cleanup 'struct i2c_device_id' initializations
- misc small battery driver cleanups and fixes"
* tag 'for-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: supply: sysfs: use power_supply_property_is_writeable()
power: supply: qcom_battmgr: Enable battery support on x1e80100
power: supply: add support for MAX1720x standalone fuel gauge
dt-bindings: power: supply: add support for MAX17201/MAX17205 fuel gauge
power: reset: piix4: add missing MODULE_DESCRIPTION() macro
power: supply: samsung-sdi-battery: Constify struct power_supply_maintenance_charge_table
power: supply: samsung-sdi-battery: Constify struct power_supply_vbat_ri_table
power: supply: lenovo_yoga_c630_battery: add Lenovo C630 driver
power: supply: ingenic: Fix some error handling paths in ingenic_battery_get_property()
power: supply: ab8500: Clean some error messages
power: supply: ab8500: Use iio_read_channel_processed_scale()
power: supply: ab8500: Fix error handling when calling iio_read_channel_processed()
power: supply: hwmon: Add support for power sensors
power: supply: ab8500: remove unused struct 'inst_curr_result_list'
power: supply: bd99954: remove unused struct 'battery_data'
power: supply: leds: Add activate() callback to triggers
power: supply: leds: Share trig pointer for online and charging_full
power: supply: leds: Add power_supply_[un]register_led_trigger()
power: supply: Drop explicit initialization of struct i2c_device_id::driver_data to 0
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt subsystem updates from Thomas Gleixner:
"Core:
- Provide a new mechanism to create interrupt domains. The existing
interfaces have already too many parameters and it's a pain to
expand any of this for new required functionality.
The new function takes a pointer to a data structure as argument.
The data structure combines all existing parameters and allows for
easy extension.
The first extension for this is to handle the instantiation of
generic interrupt chips at the core level and to allow drivers to
provide extra init/exit callbacks.
This is necessary to do the full interrupt chip initialization
before the new domain is published, so that concurrent usage sites
won't see a half initialized interrupt domain. Similar problems
exist on teardown.
This has turned out to be a real problem due to the deferred and
parallel probing which was added in recent years.
Handling this at the core level allows to remove quite some accrued
boilerplate code in existing drivers and avoids horrible
workarounds at the driver level.
- The usual small improvements all over the place
Drivers:
- Add support for LAN966x OIC and RZ/Five SoC
- Split the STM ExtI driver into a microcontroller and a SMP version
to allow building the latter as a module for multi-platform
kernels
- Enable MSI support for Armada 370XP on platforms which do not
support IPIs
- The usual small fixes and enhancements all over the place"
* tag 'irq-core-2024-07-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
irqdomain: Fix the kernel-doc and plug it into Documentation
genirq: Set IRQF_COND_ONESHOT in request_irq()
irqchip/imx-irqsteer: Handle runtime power management correctly
irqchip/gic-v3: Pass #redistributor-regions to gic_of_setup_kvm_info()
irqchip/bcm2835: Enable SKIP_SET_WAKE and MASK_ON_SUSPEND
irqchip/gic-v4: Make sure a VPE is locked when VMAPP is issued
irqchip/gic-v4: Substitute vmovp_lock for a per-VM lock
irqchip/gic-v4: Always configure affinity on VPE activation
Revert "irqchip/dw-apb-ictl: Support building as module"
Revert "Loongarch: Support loongarch avec"
arm64: Kconfig: Allow build irq-stm32mp-exti driver as module
ARM: stm32: Allow build irq-stm32mp-exti driver as module
irqchip/stm32mp-exti: Allow building as module
irqchip/stm32mp-exti: Rename internal symbols
irqchip/stm32-exti: Split MCU and MPU code
arm64: Kconfig: Select STM32MP_EXTI on STM32 platforms
ARM: stm32: Use different EXTI driver on ARMv7m and ARMv7a
irqchip/stm32-exti: Add CONFIG_STM32MP_EXTI
irqchip/dw-apb-ictl: Support building as module
irqchip/riscv-aplic: Simplify the initialization code
...
|
|
The Samsung ATNA45AF01 panel is an AMOLED eDP panel that has backlight
control over the DP AUX channel. While it works almost correctly with the
generic "edp-panel" compatible, the backlight needs special handling to
work correctly. It is similar to the existing ATNA33XC20 panel, just with
a larger resolution and size.
Add a new "samsung,atna45af01" compatible to describe this panel in the DT.
Use the existing "samsung,atna33xc20" as fallback compatible since existing
drivers should work as-is, given that resolution and size are discoverable
through the eDP link.
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240715-x1e80100-crd-backlight-v2-1-31b7f2f658a3@linaro.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- add missing MODULE_DESCRIPTION() macro
- fix offset addition for alarms
Drivers:
- isl1208: alarm clearing fixes
- mcp794xx: oscillator failure detection
- stm32: stm32mp25 support
- tps6594: power management support"
* tag 'rtc-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: stm32: add new st,stm32mp25-rtc compatible and check RIF configuration
dt-bindings: rtc: stm32: introduce new st,stm32mp25-rtc compatible
rtc: Drop explicit initialization of struct i2c_device_id::driver_data to 0
rtc: interface: Add RTC offset to alarm after fix-up
rtc: ds1307: Clamp year to valid BCD (0-99) in `set_time()`
rtc: ds1307: Detect oscillator fail on mcp794xx
rtc: isl1208: Update correct procedure for clearing alarm
rtc: isl1208: Add a delay for clearing alarm
dt-bindings: rtc: Convert rtc-fsl-ftm-alarm.txt to yaml format
rtc: add missing MODULE_DESCRIPTION() macro
rtc: abx80x: Fix return value of nvmem callback on read
rtc: cmos: Fix return value of nvmem callbacks
rtc: isl1208: Fix return value of nvmem callbacks
rtc: tps6594: Add power management support
rtc: tps6594: introduce private structure as drvdata
rtc: tps6594: Fix memleak in probe
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Some new drivers is the main part, the rest is cleanups and nonurgent
fixes.
Nothing much special about this, no core changes this time.
New drivers:
- Renesas RZ/V2H(P) SoC
- NXP Freescale i.MX91 SoC
- Nuvoton MA35D1 SoC
- Qualcomm PMC8380, SM4250, SM4250 LPI
Enhancements:
- A slew of scoped-based simplifications of of_node_put()"
* tag 'pinctrl-v6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (110 commits)
pinctrl: renesas: rzg2l: Support output enable on RZ/G2L
pinctrl: renesas: rzg2l: Clean up and refactor OEN read/write functions
pinctrl: renesas: rzg2l: Clarify OEN read/write support
dt-bindings: pinctrl: pinctrl-single: Fix pinctrl-single,gpio-range description
dt-bindings: pinctrl: npcm8xx: add missing pin group and mux function
dt-bindings: pinctrl: pinctrl-single: fix schmitt related properties
pinctrl: freescale: Use scope based of_node_put() cleanups
pinctrl: equilibrium: Use scope based of_node_put() cleanups
pinctrl: ti: iodelay: Use scope based of_node_put() cleanups
pinctrl: qcom: lpass-lpi: increase MAX_NR_GPIO to 32
pinctrl: cy8c95x0: Update cache modification
pinctrl: cy8c95x0: Use cleanup.h
pinctrl: renesas: r8a779h0: Remove unneeded separators
pinctrl: renesas: r8a779g0: Add INTC-EX pins, groups, and function
pinctrl: renesas: r8a779g0: Remove unneeded separators
pinctrl: renesas: r8a779h0: Add AVB MII pins and groups
pinctrl: renesas: r8a779g0: Fix TPU suffixes
pinctrl: renesas: r8a779g0: Fix TCLK suffixes
pinctrl: renesas: r8a779g0: FIX PWM suffixes
pinctrl: renesas: r8a779g0: Fix IRQ suffixes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"Nothing stands out for this merge window, mostly minor fixes, such as
module descriptions, the use of debug macros and Makefile
improvements.
Raw NAND changes;
- The Freescale MXC driver has been converted to the newer
'->exec_op()' interface
- The meson driver now supports handling the boot ROM area with very
specific ECC needs
- Support for the iMX8QXP has been added to the GPMI driver
- The lpx32xx driver now can get the DMA channels using DT entries
- The Qcom binding has been improved to be more future proof by Rob
- And then there is the usual load of misc and minor changes
SPI-NAND changes:
- The Macronix vendor driver has been improved to support an extended
ID to avoid conflicting with older devices after an ID reuse issue
SPI NOR changes:
- Drop support for Xilinx S3AN flashes. These flashes are for the
very old Xilinx Spartan 3 FPGAs and they need some awkward code in
the core to support.
Drop support for these flashes, along with the special handling we
needed for them in the core like non-power-of-2 page size handling
and the .setup() callback.
- Fix regression for old w25q128 flashes without SFDP tables.
Commit 83e824a4a595 ("mtd: spi-nor: Correct flags for Winbond
w25q128") dropped support for such devices under the assumption
that they aren't being used anymore. Users have now surfaced [0] so
fix the regression by supporting both kind of devices.
- Core cleanups including removal of SPI_NOR_NO_FR flag and
simplification of spi_nor_get_flash_info()"
Link: https://lore.kernel.org/r/CALxbwRo_-9CaJmt7r7ELgu+vOcgk=xZcGHobnKf=oT2=u4d4aA@mail.gmail.com/ [0]
* tag 'mtd/for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (28 commits)
mtd: rawnand: lpx32xx: Fix dma_request_chan() error checks
mtd: spinand: macronix: Add support for serial NAND flash
mtd: spinand: macronix: Add support for reading Device ID 2
mtd: rawnand: lpx32xx: Request DMA channels using DT entries
dt-bindings: mtd: qcom,nandc: Define properties at top-level
mtd: rawnand: intel: use 'time_left' variable with wait_for_completion_timeout()
mtd: rawnand: mxc: use 'time_left' variable with wait_for_completion_timeout()
mtd: rawnand: gpmi: add iMX8QXP support.
mtd: rawnand: gpmi: add 'support_edo_timing' in gpmi_devdata
mtd: cmdlinepart: Replace `dbg()` macro with `pr_debug()`
mtd: add missing MODULE_DESCRIPTION() macros
mtd: make mtd_test.c a separate module
dt-bindings: mtd: gpmi-nand: Add 'fsl,imx8qxp-gpmi-nand' compatible string
mtd: rawnand: cadence: remove unused struct 'ecc_info'
mtd: rawnand: mxc: support software ECC
mtd: rawnand: mxc: implement exec_op
mtd: rawnand: mxc: separate page read from ecc calc
mtd: spi-nor: winbond: fix w25q128 regression
mtd: spi-nor: simplify spi_nor_get_flash_info()
mtd: spi-nor: get rid of SPI_NOR_NO_FR
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Support for various new ISA extensions:
* The Zve32[xf] and Zve64[xfd] sub-extensios of the vector
extension
* Zimop and Zcmop for may-be-operations
* The Zca, Zcf, Zcd and Zcb sub-extensions of the C extension
* Zawrs
- riscv,cpu-intc is now dtschema
- A handful of performance improvements and cleanups to text patching
- Support for memory hot{,un}plug
- The highest user-allocatable virtual address is now visible in
hwprobe
* tag 'riscv-for-linus-6.11-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (58 commits)
riscv: lib: relax assembly constraints in hweight
riscv: set trap vector earlier
KVM: riscv: selftests: Add Zawrs extension to get-reg-list test
KVM: riscv: Support guest wrs.nto
riscv: hwprobe: export Zawrs ISA extension
riscv: Add Zawrs support for spinlocks
dt-bindings: riscv: Add Zawrs ISA extension description
riscv: Provide a definition for 'pause'
riscv: hwprobe: export highest virtual userspace address
riscv: Improve sbi_ecall() code generation by reordering arguments
riscv: Add tracepoints for SBI calls and returns
riscv: Optimize crc32 with Zbc extension
riscv: Enable DAX VMEMMAP optimization
riscv: mm: Add support for ZONE_DEVICE
virtio-mem: Enable virtio-mem for RISC-V
riscv: Enable memory hotplugging for RISC-V
riscv: mm: Take memory hotplug read-lock during kernel page table dump
riscv: mm: Add memory hotplugging support
riscv: mm: Add pfn_to_kaddr() implementation
riscv: mm: Refactor create_linear_mapping_range() for memory hot add
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- add support for Realtek RTL9302C
- add support for Mobileye EyeQ6H
- add support for Mobileye EyeQ OLB system controller
- improve r4k clocksource
- add mode for emulating ieee754 NAN2008
- rework for BMIPS CBR address handling
- fixes for Loongson 2K1000
- defconfig updates
- cleanups and fixes
* tag 'mips_6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (58 commits)
MIPS: config: Add ip30_defconfig
MIPS: config: lemote2f: Regenerate defconfig
MIPS: config: generic: Add board-litex
MIPS: config: Enable MSA and virtualization for MIPS64R6
MIPS: Fix fallback march for SB1
mips: dts: realtek: Add RTL9302C board
mips: generic: add fdt fixup for Realtek reference board
mips: select REALTEK_OTTO_TIMER for Realtek platforms
dt-bindings: interrupt-controller: realtek,rtl-intc: Add rtl9300-intc
dt-bindings: mips: realtek: Add rtl930x-soc compatible
dt-bindings: vendor-prefixes: Add Cameo Communications
mips: dts: realtek: add device_type property to cpu node
mips: dts: realtek: use "serial" instead of "uart" in node name
MIPS: Implement ieee754 NAN2008 emulation mode
MIPS: lantiq: improve USB initialization
MIPS: GIC: Generate redirect block accessors
MIPS: CPS: Add a couple of multi-cluster utility functions
MIPS: Octeron: remove source file executable bit
MAINTAINERS: Mobileye: add OLB drivers and dt-bindings
MIPS: mobileye: eyeq5: add OLB system-controller node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Define PCIE_RESET_CONFIG_DEVICE_WAIT_MS for the generic 100ms
required after reset before config access (Kevin Xie)
- Define PCIE_T_RRS_READY_MS for the generic 100ms required after
reset before config access (probably should be unified with
PCIE_RESET_CONFIG_DEVICE_WAIT_MS) (Damien Le Moal)
Resource management:
- Rename find_resource() to find_resource_space() to be more
descriptive (Ilpo Järvinen)
- Export find_resource_space() for use by PCI core, which needs to
learn whether there is available space for a bridge window (Ilpo
Järvinen)
- Prevent double counting of resources so window size doesn't grow on
each remove/rescan cycle (Ilpo Järvinen)
- Relax bridge window sizing algorithm so a device doesn't break
simply because it was removed and rescanned (Ilpo Järvinen)
- Evaluate the ACPI PRESERVE_BOOT_CONFIG _DSM in
pci_register_host_bridge() (not acpi_pci_root_create()) so we can
unify it with similar DT functionality (Vidya Sagar)
- Extend use of DT "linux,pci-probe-only" property so it works
per-host bridge as well as globally (Vidya Sagar)
- Unify support for ACPI PRESERVE_BOOT_CONFIG _DSM and the DT
"linux,pci-probe-only" property in pci_preserve_config() (Vidya
Sagar)
Driver binding:
- Add devres infrastructure for managed request and map of partial
BAR resources (Philipp Stanner)
- Deprecate pcim_iomap_table() because uses like
"pcim_iomap_table()[0]" have no good way to return errors (Philipp
Stanner)
- Add an always-managed pcim_request_region() for use instead of
pci_request_region() and similar, which are sometimes managed
depending on whether pcim_enable_device() has been called
previously (Philipp Stanner)
- Reimplement pcim_set_mwi() so it doesn't need to keep store MWI
state (Philipp Stanner)
- Add pcim_intx() for use instead of pci_intx(), which is sometimes
managed depending on whether pcim_enable_device() has been called
previously (Philipp Stanner)
- Add managed pcim_iomap_range() to allow mapping of a partial BAR
(Philipp Stanner)
- Fix a devres mapping leak in drm/vboxvideo (Philipp Stanner)
Error handling:
- Add missing bridge locking in device reset path and add a warning
for other possible lock issues (Dan Williams)
- Fix use-after-free on concurrent DPC and hot-removal (Lukas Wunner)
Power management:
- Disable AER and DPC during suspend to avoid spurious wakeups if
they share an interrupt with PME (Kai-Heng Feng)
PCIe native device hotplug:
- Detect if a device was removed or replaced during system sleep so
we don't assume a new device is the one that used to be there
(Lukas Wunner)
Virtualization:
- Add an ACS quirk for Broadcom BCM5760X multi-function NIC; it
prevents transactions between functions even though it doesn't
advertise ACS, so the functions can be attached individually via
VFIO (Ajit Khaparde)
Peer-to-peer DMA:
- Add a "pci=config_acs=" kernel command-line parameter to relax
default ACS settings to enable additional peer-to-peer
configurations. Requires expert knowledge of topology and ACS
operation (Vidya Sagar)
Endpoint framework:
- Remove unused struct pci_epf_group.type_group (Christophe JAILLET)
- Fix error handling in vpci_scan_bus() and epf_ntb_epc_cleanup()
(Dan Carpenter)
- Make struct pci_epc_class constant (Greg Kroah-Hartman)
- Remove unused pci_endpoint_test_bar_{readl,writel} functions
(Jiapeng Chong)
- Rename "BME" to "Bus Master Enable" (Manivannan Sadhasivam)
- Rename struct pci_epc_event_ops.core_init() callback to epc_init()
(Manivannan Sadhasivam)
- Move DMA init to MHI .epc_init() callback for uniformity
(Manivannan Sadhasivam)
- Cancel EPF test delayed work when link goes down (Manivannan
Sadhasivam)
- Add struct pci_epc_event_ops.epc_deinit() callback for cleanup
needed on fundamental reset (Manivannan Sadhasivam)
- Add 64KB alignment to endpoint test to support Rockchip rk3588
(Niklas Cassel)
- Optimize endpoint test by using memcpy() instead of readl() (Niklas
Cassel)
Device tree bindings:
- Add generic "ats-supported" property to advertise that a PCIe Root
Complex supports ATS (Jean-Philippe Brucker)
Amazon Annapurna Labs PCIe controller driver:
- Validate IORESOURCE_BUS presence to avoid NULL pointer dereference
(Aleksandr Mishin)
Axis ARTPEC-6 PCIe controller driver:
- Rename .cpu_addr_fixup() parameter to reflect that it is a PCI
address, not a CPU address (Niklas Cassel)
Freescale i.MX6 PCIe controller driver:
- Convert to agnostic GPIO API (Andy Shevchenko)
Freescale Layerscape PCIe controller driver:
- Make struct mobiveil_rp_ops constant (Christophe JAILLET)
- Use new generic dw_pcie_ep_linkdown() to handle link-down events
(Manivannan Sadhasivam)
HiSilicon Kirin PCIe controller driver:
- Convert to agnostic GPIO API (Andy Shevchenko)
- Use _scoped() iterator for OF children to ensure refcounts are
decremented at loop exit (Javier Carrasco)
Intel VMD host bridge driver:
- Create sysfs "domain" symlink before downstream devices are exposed
to userspace by pci_bus_add_devices() (Jiwei Sun)
Loongson PCIe controller driver:
- Enable MSI when LS7A is used with new CPUs that have integrated
PCIe Root Complex, e.g., Loongson-3C6000, so downstream devices can
use MSI (Huacai Chen)
Microchip AXI PolarFlare PCIe controller driver:
- Move pcie-microchip-host.c to a new PLDA directory (Minda Chen)
- Factor PLDA generic items out to a common
plda,xpressrich3-axi-common.yaml binding (Minda Chen)
- Factor PLDA generic data structures and code out to shared
pcie-plda.h, pcie-plda-host.c (Minda Chen)
- Add PLDA generic interrupt handling with a .request_event_irq()
callback for vendor-specific events (Minda Chen)
- Add PLDA generic host init/deinit and map bus functions for use by
vendor-specific drivers (Minda Chen)
- Rework to use PLDA core (Minda Chen)
Microsoft Hyper-V host bridge driver:
- Return zero, not garbage, when reading PCI_INTERRUPT_PIN (Wei Liu)
NVIDIA Tegra194 PCIe controller driver:
- Remove unused struct tegra_pcie_soc (Dr. David Alan Gilbert)
- Set 64KB inbound ATU alignment restriction (Jon Hunter)
Qualcomm PCIe controller driver:
- Make the MHI reg region mandatory for X1E80100, since all PCIe
controllers have it (Abel Vesa)
- Prevent use of uninitialized data and possible error pointer
dereference (Dan Carpenter)
- Return error, not success, if dev_pm_opp_find_freq_floor() fails
(Dan Carpenter)
- Add Operating Performance Points (OPP) support to scale performance
state based on aggregate link bandwidth to improve SoC power
efficiency (Krishna chaitanya chundru)
- Vote for the CPU-PCIe ICC (interconnect) path to ensure it stays
active even if other drivers don't vote for it (Krishna chaitanya
chundru)
- Use devm_clk_bulk_get_all() to get all the clocks from DT to avoid
writing out all the clock names (Manivannan Sadhasivam)
- Add DT binding and driver support for the SA8775P SoC (Mrinmay
Sarkar)
- Add HDMA support for the SA8775P SoC (Mrinmay Sarkar)
- Override the SA8775P NO_SNOOP default to avoid possible memory
corruption (Mrinmay Sarkar)
- Make sure resources are disabled during PERST# assertion, even if
the link is already disabled (Manivannan Sadhasivam)
- Use new generic dw_pcie_ep_linkdown() to handle link-down events
(Manivannan Sadhasivam)
- Add DT and endpoint driver support for the SA8775P SoC (Mrinmay
Sarkar)
- Add Hyper DMA (HDMA) support for the SA8775P SoC and enable it in
the EPF MHI driver (Mrinmay Sarkar)
- Set PCIE_PARF_NO_SNOOP_OVERIDE to override the default NO_SNOOP
attribute on the SA8775P SoC (both Root Complex and Endpoint mode)
to avoid possible memory corruption (Mrinmay Sarkar)
Renesas R-Car PCIe controller driver:
- Demote WARN() to dev_warn_ratelimited() in rcar_pcie_wakeup() to
avoid unnecessary backtrace (Marek Vasut)
- Add DT and driver support for R-Car V4H (R8A779G0) host and
endpoint. This requires separate proprietary firmware (Yoshihiro
Shimoda)
Rockchip PCIe controller driver:
- Assert PERST# for 100ms after power is stable (Damien Le Moal)
- Wait PCIE_T_RRS_READY_MS (100ms) after reset before starting
configuration (Damien Le Moal)
- Use GPIOD_OUT_LOW flag while requesting ep_gpio to fix a firmware
crash on Qcom-based modems with Rockpro64 board (Manivannan
Sadhasivam)
Rockchip DesignWare PCIe controller driver:
- Factor common parts of rockchip-dw-pcie DT binding to be shared by
Root Complex and Endpoint mode (Niklas Cassel)
- Add missing INTx signals to common DT binding (Niklas Cassel)
- Add eDMA items to DT binding for Endpoint controller (Niklas
Cassel)
- Fix initial dw-rockchip PERST# GPIO value to prevent unnecessary
short assert/deassert that causes issues with some WLAN controllers
(Niklas Cassel)
- Refactor dw-rockchip and add support for Endpoint mode (Niklas
Cassel)
- Call pci_epc_init_notify() and drop dw_pcie_ep_init_notify()
wrapper (Niklas Cassel)
- Add error messages in .probe() error paths to improve user
experience (Uwe Kleine-König)
Samsung Exynos PCIe controller driver:
- Use bulk clock APIs to simplify clock setup (Shradha Todi)
StarFive PCIe controller driver:
- Add DT binding and driver support for the StarFive JH7110
PLDA-based PCIe controller (Minda Chen)
Synopsys DesignWare PCIe controller driver:
- Add generic support for sending PME_Turn_Off when system suspends
(Frank Li)
- Fix incorrect interpretation of iATU slot 0 after PERST#
assert/deassert (Frank Li)
- Use msleep() instead of usleep_range() while waiting for link
(Konrad Dybcio)
- Refactor dw_pcie_edma_find_chip() to enable adding support for
Hyper DMA (HDMA) (Manivannan Sadhasivam)
- Enable drivers to supply the eDMA channel count since some can't
auto detect this (Manivannan Sadhasivam)
- Call pci_epc_init_notify() and drop dw_pcie_ep_init_notify()
wrapper (Manivannan Sadhasivam)
- Pass the eDMA mapping format directly from drivers instead of
maintaining a capability for it (Manivannan Sadhasivam)
- Add generic dw_pcie_ep_linkdown() to notify EPF drivers about
link-down events and restore non-sticky DWC registers lost on link
down (Manivannan Sadhasivam)
- Add vendor-specific "apb" reg name, interrupt names, INTx names to
generic binding (Niklas Cassel)
- Enforce DWC restriction that 64-bit BARs must start with an
even-numbered BAR (Niklas Cassel)
- Consolidate args of dw_pcie_prog_outbound_atu() into a structure
(Yoshihiro Shimoda)
- Add support for endpoints to send Message TLPs, e.g., for INTx
emulation (Yoshihiro Shimoda)
TI DRA7xx PCIe controller driver:
- Rename .cpu_addr_fixup() parameter to reflect that it is a PCI
address, not a CPU address (Niklas Cassel)
TI Keystone PCIe controller driver:
- Validate IORESOURCE_BUS presence to avoid NULL pointer dereference
(Aleksandr Mishin)
- Work around AM65x/DRA80xM Errata #i2037 that corrupts TLPs and
causes processor hangs by limiting Max_Read_Request_Size (MRRS) and
Max_Payload_Size (MPS) (Kishon Vijay Abraham I)
- Leave BAR 0 disabled for AM654x to fix a regression caused by
6ab15b5e7057 ("PCI: dwc: keystone: Convert .scan_bus() callback to
use add_bus"), which caused a 45-second boot delay (Siddharth
Vadapalli)
Xilinx Versal CPM PCIe controller driver:
- Fix overlapping bridge registers and 32-bit BAR addresses in DT
binding (Thippeswamy Havalige)
MicroSemi Switchtec management driver:
- Make struct switchtec_class constant (Greg Kroah-Hartman)
Miscellaneous:
- Remove unused struct acpi_handle_node (Dr. David Alan Gilbert)
- Add missing MODULE_DESCRIPTION() macros (Jeff Johnson)"
* tag 'pci-v6.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (154 commits)
PCI: loongson: Enable MSI in LS7A Root Complex
PCI: Extend ACS configurability
PCI: Add missing bridge lock to pci_bus_lock()
drm/vboxvideo: fix mapping leaks
PCI: Add managed pcim_iomap_range()
PCI: Remove legacy pcim_release()
PCI: Add managed pcim_intx()
PCI: vmd: Create domain symlink before pci_bus_add_devices()
PCI: qcom: Prevent use of uninitialized data in qcom_pcie_suspend_noirq()
PCI: qcom: Prevent potential error pointer dereference
PCI: qcom: Fix missing error code in qcom_pcie_probe()
PCI: Give pcim_set_mwi() its own devres cleanup callback
PCI: Move struct pci_devres.pinned bit to struct pci_dev
PCI: Remove struct pci_devres.enabled status bit
PCI: Document hybrid devres hazards
PCI: Add managed pcim_request_region()
PCI: Deprecate pcim_iomap_table(), pcim_iomap_regions_request_all()
PCI: Add managed partial-BAR request and map infrastructure
PCI: Add devres helpers for iomap table
PCI: Add and use devres helper for bit masks
...
|
|
I2C MUXes described by the i2c-gpio-mux sometimes need a significant
amount of time to switch from a bus to another. When a new bus is
selected, the first I2C transfer can fail if it occurs too early. There
is no way to describe this transition delay that has to be waited before
starting the first I2C transfer.
Add a 'settle-time-us' property that indicates the delay to be
respected before doing the first i2c transfer.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Add sm8650 compatible consistent with CAMSS CCI interfaces.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Add sm8550 compatible consistent with CAMSS CCI interfaces, the list of
clocks is reduced by removing "slow_ahb_src" clock, which is derived
from "cpas_ahb" clock.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- streamlined logic in input core for handling normal input handlers vs
input filters
- updates to input drivers to allocate memory with sizeof(*pointer)
instead of sizeof(type)
- change to ads7846 touchscreen driver to use hsync GPIO instead of
requiring platform data with special method (which is not compatible
with boards using device tree)
- update to adc-joystick driver to handle inverted axes
- cleanups in various drivers switching them to use the new "guard" and
"__free()" facilities
- changes to several drivers (adxl34x, atmel_mxt_ts, ati-remote2,
omap-keypad, yealink) to stop creating driver-specific device
attributes manually and use driver core facilities for this
- update to Cypress PS/2 protocol driver to properly handle errors from
the PS/2 transport as well as other cleanups
- update to edt-ft5x06 driver to support ft5426 variant
- update to ektf2127 driver to support ektf2232 variant
- update to exc3000 driver to support EXC81W32 variant
- update to imagis driver to support IST3038 variant
- other assorted driver cleanups.
* tag 'input-for-v6.11-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (71 commits)
Input: yealink - simplify locking in sysfs attribute handling
Input: yealink - use driver core to instantiate device attributes
Input: ati-remote2 - use driver core to instantiate device attributes
Input: omap-keypad - use driver core to instantiate device attributes
Input: atmel_mxt_ts - use driver core to instantiate device attributes
Input: exc3000 - add EXC81W32 support
dt-bindings: input: touchscreen: exc3000: add EXC81W32
Input: twl4030-pwrbutton - fix kernel-doc warning
Input: himax_hx83112b - add support for HX83100A
Input: himax_hx83112b - add himax_chip struct for multi-chip support
Input: himax_hx83112b - implement MCU register reading
Input: himax_hx83112b - use more descriptive register defines
dt-bindings: input: touchscreen: himax,hx83112b: add HX83100A
Input: do not check number of events in input_pass_values()
Input: preallocate memory to hold event values
Input: rearrange input_alloc_device() to prepare for preallocating of vals
Input: simplify event handling logic
Input: make events() method return number of events processed
Input: make sure input handlers define only one processing method
Input: evdev - remove ->event() method
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"The I2C core gains documentation updates for the testunit, a cleanup
regarding unneeded 'driver_data' and more sanity checks in the char
device.
For the host drivers, this release includes significant updates, with
the primary change being the renaming from "master/slave" to
"controller/target" to adhere to I2C v7 and SMBus 3.2 standards.
New Support:
- Added support for Intel Arrow Lake-H
- Added I2C support in the Arioha SoC by linking the Mediatek I2C
controller
Cleanups:
- Added the MODULE_DESCRIPTION() macro, resolving a modpost warning
in the ALi 1563 Southbridge driver.
- Constified the regmap_config declaration in the i2c-designware
driver.
- Improved the coding style in the Renesas R-Car driver by removing
unnecessary semicolons after brackets.
General improvements:
- In the OMAP device, replaced NOIRQ_SYSTEM_SLEEP_PM_OPS with
RUNTIME_PM_OPS to enable waking up the controller during suspend()
before suspend_noirq() kicks in.
- Improved logging in the Xilinx driver.
- Added a warning (WARN()) in the Renesas R-Car driver for spurious
interrupts.
DTS Changes:
- Removed address-cell and size-cell from the Atmel at91sam, nVidia
Tegra 20, and Samsung S3c2410 devices.
- Fixed Texas Instruments OMAP4 I2C controller to comply with the
i2c-controller.yaml schema.
- Improved indentation in DTS examples for several I2C devices.
- Converted the NXP LPC1788 binding to the dt-schema.
- Added documentation for the compatible string thead,th1520-i2c.
- Added the "power-domains" property for the Meson I2C driver.
AT24 EEPROM driver changes:
- add support for two new Microchip models
- document even more new models in DT bindings (those use fallback
compatibles so no code changes)"
* tag 'i2c-for-6.11-rc1-try2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (87 commits)
i2c: document new callbacks in i2c_algorithm
dt-bindings: i2c: amlogic,meson6-i2c: add optional power-domains
dt-bindings: i2c: at91: Add sama7d65 compatible string
i2c: st: reword according to newest specification
i2c: cpm: reword according to newest specification
i2c: virtio: reword according to newest specification
i2c: nvidia-gpu: reword according to newest specification
i2c: viai2c: reword according to newest specification
i2c: viperboard: reword according to newest specification
i2c: uniphier: reword according to newest specification
i2c: uniphier-f: reword according to newest specification
i2c: tiny-usb: reword according to newest specification
i2c: thunderx-pcidrv: reword according to newest specification
i2c: tegra-bpmp: reword according to newest specification
i2c: taos-evm: reword according to newest specification
i2c: sun6i-p2wi: reword according to newest specification
i2c: stm32f4: reword according to newest specification
i2c: sprd: reword according to newest specification
i2c: sis5595: reword according to newest specification
i2c: rzv2m: reword according to newest specification
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc and other driver updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystem changes
for 6.11-rc1. Nothing major in here, just loads of new drivers and
updates. Included in here are:
- IIO api updates and new drivers added
- wait_interruptable_timeout() api cleanups for some drivers
- MODULE_DESCRIPTION() additions for loads of drivers
- parport out-of-bounds fix
- interconnect driver updates and additions
- mhi driver updates and additions
- w1 driver fixes
- binder speedups and fixes
- eeprom driver updates
- coresight driver updates
- counter driver update
- new misc driver additions
- other minor api updates
All of these, EXCEPT for the final Kconfig build fix for 32bit
systems, have been in linux-next for a while with no reported issues.
The Kconfig fixup went in 29 hours ago, so might have missed the
latest linux-next, but was acked by everyone involved"
* tag 'char-misc-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (330 commits)
misc: Kconfig: exclude mrvl-cn10k-dpi compilation for 32-bit systems
misc: delete Makefile.rej
binder: fix hang of unregistered readers
misc: Kconfig: add a new dependency for MARVELL_CN10K_DPI
virtio: add missing MODULE_DESCRIPTION() macro
agp: uninorth: add missing MODULE_DESCRIPTION() macro
spmi: add missing MODULE_DESCRIPTION() macros
dev/parport: fix the array out-of-bounds risk
samples: configfs: add missing MODULE_DESCRIPTION() macro
misc: mrvl-cn10k-dpi: add Octeon CN10K DPI administrative driver
misc: keba: Fix missing AUXILIARY_BUS dependency
slimbus: Fix struct and documentation alignment in stream.c
MAINTAINERS: CC dri-devel list on Qualcomm FastRPC patches
misc: fastrpc: use coherent pool for untranslated Compute Banks
misc: fastrpc: support complete DMA pool access to the DSP
misc: fastrpc: add missing MODULE_DESCRIPTION() macro
misc: fastrpc: Add missing dev_err newlines
misc: fastrpc: Use memdup_user()
nvmem: core: Implement force_ro sysfs attribute
nvmem: Use sysfs_emit() for type attribute
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.11-rc1.
Nothing earth-shattering in here, just constant forward progress in
adding support for new hardware and better debugging functionalities
for thunderbolt devices and the subsystem. Included in here are:
- thunderbolt debugging update and driver additions
- xhci driver updates
- typec driver updates
- kselftest device driver changes (acked by the relevant maintainers,
depended on other changes in this tree.)
- cdns3 driver updates
- gadget driver updates
- MODULE_DESCRIPTION() additions
- dwc3 driver updates and fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (112 commits)
kselftest: devices: Add test to detect device error logs
kselftest: Move ksft helper module to common directory
kselftest: devices: Move discoverable devices test to subdirectory
usb: gadget: f_uac2: fix non-newline-terminated function name
USB: uas: Implement the new shutdown callback
USB: core: add 'shutdown' callback to usb_driver
usb: typec: Drop explicit initialization of struct i2c_device_id::driver_data to 0
usb: dwc3: enable CCI support for AMD-xilinx DWC3 controller
usb: dwc2: add support for other Lantiq SoCs
usb: gadget: Use u16 types for 16-bit fields
usb: gadget: midi2: Fix incorrect default MIDI2 protocol setup
usb: dwc3: core: Check all ports when set phy suspend
usb: typec: tcpci: add support to set connector orientation
dt-bindings: usb: Convert fsl-usb to yaml
usb: typec: ucsi: reorder operations in ucsi_run_command()
usb: typec: ucsi: extract common code for command handling
usb: typec: ucsi: inline ucsi_read_message_in
usb: typec: ucsi: rework command execution functions
usb: typec: ucsi: split read operation
usb: typec: ucsi: simplify command sending API
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is a small set of tty and serial driver updates for 6.11-rc1. Not
much happened this cycle, unlike the previous kernel release which had
lots of "excitement" in this part of the kernel. Included in here are
the following changes:
- dt binding updates for new platforms
- 8250 driver updates
- various small serial driver fixes and updates
- printk/console naming and matching attempt #2 (was reverted for
6.10-final, should be good to go this time around, acked by the
relevant maintainers).
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (22 commits)
Documentation: kernel-parameters: Add DEVNAME:0.0 format for serial ports
serial: core: Add serial_base_match_and_update_preferred_console()
printk: Add match_devname_and_update_preferred_console()
serial: sc16is7xx: hardware reset chip if reset-gpios is defined in DT
dt-bindings: serial: sc16is7xx: add reset-gpios
dt-bindings: serial: vt8500-uart: convert to json-schema
serial: 8250_platform: Explicitly show we initialise ISA ports only once
tty: add missing MODULE_DESCRIPTION() macros
dt-bindings: serial: mediatek,uart: add MT7988
serial: sh-sci: Add support for RZ/V2H(P) SoC
dt-bindings: serial: Add documentation for Renesas RZ/V2H(P) (R9A09G057) SCIF support
dt-bindings: serial: renesas,scif: Make 'interrupt-names' property as required
dt-bindings: serial: renesas,scif: Validate 'interrupts' and 'interrupt-names'
dt-bindings: serial: renesas,scif: Move ref for serial.yaml at the end
riscv: dts: starfive: jh7110: Add the core reset and jh7110 compatible for uarts
serial: 8250_dw: Use reset array API to get resets
dt-bindings: serial: snps-dw-apb-uart: Add one more reset signal for StarFive JH7110 SoC
serial: 8250: Extract platform driver
serial: 8250: Extract RSA bits
serial: imx: stop casting struct uart_port to struct imx_port
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Lots of changes in this cycle, but mostly for cleanups and
refactoring.
Significant amount of changes are about DT schema conversions for ASoC
at this time while we see other usual suspects, too.
Some highlights below:
Core:
- Re-introduction of PCM sync ID support API
- MIDI2 time-base extension in ALSA sequencer API
ASoC:
- Syncing of features between simple-audio-card and the two
audio-graph cards
- Support for specifying the order of operations for components
within cards to allow quirking for unusual systems
- Lots of DT schema conversions
- Continued SOF/Intel updates for topology, SoundWire, IPC3/4
- New support for Asahi Kasei AK4619, Cirrus Logic CS530x, Everest
Semiconductors ES8311, NXP i.MX95 and LPC32xx, Qualcomm LPASS v2.5
and WCD937x, Realtek RT1318 and RT1320 and Texas Instruments
PCM5242
HD-audio:
- More quirks, Intel PantherLake support, senarytech codec support
- Refactoring of Cirrus codec component-binding
Others:
- ALSA control kselftest improvements, and fixes for input value
checks in various drivers"
* tag 'sound-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (349 commits)
kselftest/alsa: Log the PCM ID in pcm-test
kselftest/alsa: Use card name rather than number in test names
ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book Pro 360
ALSA: hda/tas2781: Add new quirk for Lenovo Hera2 Laptop
ALSA: seq: ump: Skip useless ports for static blocks
ALSA: pcm_dmaengine: Don't synchronize DMA channel when DMA is paused
ALSA: usb: Use BIT() for bit values
ALSA: usb: Fix UBSAN warning in parse_audio_unit()
ALSA: hda/realtek: Enable headset mic on Positivo SU C1400
ASoC: tas2781: Add new Kontrol to set tas2563 digital Volume
ASoC: codecs: wcd937x: Remove separate handling for vdd-buck supply
ASoC: codecs: wcd937x: Remove the string compare in MIC BIAS widget settings
ASoC: codecs: wcd937x-sdw: Fix Unbalanced pm_runtime_enable
ASoC: dt-bindings: cirrus,cs42xx8: Convert to dtschema
ASoC: cs530x: Remove bclk from private structure
ASoC: cs530x: Calculate proper bclk rate using TDM
ASoC: dt-bindings: cirrus,cs4270: Convert to dtschema
firmware: cs_dsp: Rename fw_ver to wmfw_ver
firmware: cs_dsp: Clarify wmfw format version log message
firmware: cs_dsp: Make wmfw and bin filename arguments const char *
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This a large collection of clk driver updates and a handful of new SoC
clk driver support.
We have the usual Qualcomm clk drivers, along with clk drivers for the
Sophgo and T-Head vendors, all to support some new SoCs.
Nothing in particular stands out to me in the updates. There's the
interconnect clk driver which exposes clks as interconnects, crossing
subsystems. There's a bunch of janitorial things that are improving
drivers in general like kmemdup_array() or fixing error paths. But
overall the updates look normal to fix the description data which is
usually the stuff that's wrong and/or untested.
Core:
- Skip gate basic type KUnit tests on s390 due to lack of MMIO
emulation
New Drivers:
- AP sub-system clock controller in the T-Head TH1520
- Sophgo Sophon sg2042 clk driver
- Qualcomm SM7150 camera, display and video clk drivers
- Qualcomm QCM2290 GPU clk driver
- Qualcomm QCS8386/QCS8084 NSS clk driver
- Qualcomm SM8650 camera and video drivers
Updates:
- Add reset support to Airoha EN7581 clk driver
- Add MODULE_DESCRIPTIONs to various clk drivers
- Introduce helper logic to expose clock controllers as simple
interconnect providers
- Use the interconnect helper above on Qualcomm ipq9574
- Add CLK_SET_RATE_PARENT to the remaining USB pipe clocks on
Qualcomm X1Elite
- Improve error handling in Qualcomm kpss-xcc driver
- Mark Qualcomm SC8280XP LPASS clock controller regmap_config const
- Export more clocks for Rockchip rk3128 peripherals
- Convert Rockchip clk drivers to use kmemdup_array()
- Drop CLK_NR_CLKS from Rockchip rk3128 and rk3188 binding headers
- Make qcom_cc_really_probe() take a struct device to allow reuse in
non-platform-drivers
- Introduce prepare-only branch clock ops in the qcom clk driver to
support clocks on buses that take locks
- Describe parent/child relationship for Qualcomm SC7280 camera GDSCs
- Support Qualcomm Huayra 2290 alpha PLL
- Adjust the highest SDCC clock frequency on Qualcomm IPQ6018 to
match HS200 support
- Add missing PCIe PIPE clocks on Qualcomm IPQ9574
- Fix various configurations and properties in the Qualcomm SA8775P,
X1E80100 and SM7280 drivers
- Park Qualcomm SM8350 GPU RCGs on XO while disabled
- Remove unused CONFIG_QCOM_RPMCC Kconfig symbol
- exynos-clkout: Remove usage of of_device_id table as
.of_match_table, because the driver is instantiated as MFD cell,
not as standalone platform driver. Populated .of_match_table
confused people few times to convert the code to
device_get_match_data(), which broke the driver
- Mark one Samsung UFS clock as critical, because having it off stops
the system from shutdown
- Use kmemdup_array() when applicable
- Remove unused 'struct gates_data' from old sunxi driver library
- Add GPADC clock and reset for Allwinner H616
- Minor Amlogic S4 clock fixes
- DT bindings Yaml conversion of the Amlogic AXG audio controller
- Amlogic C3 clock controllers support
- Amlogic clk flag added to skip init of already enabled PLLs and
avoid relocking
- Amlogic A1 DT bindings updates for system pll support
- Add missing MODULE_DESCRIPTION where necessary
- Remove obsolete clock DT binding header files
- Add Battery Backup (VBATTB) and I2C clocks, resets, and power
domains on Renesas RZ/G3S
- Add audio clocks on Renesas R-Car V4M
- Add video capture (ISPCS, CSI-2, VIN) clocks on Renesas R-Car V4M"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (135 commits)
clk: thead: Add support for T-Head TH1520 AP_SUBSYS clocks
dt-bindings: clock: Document T-Head TH1520 AP_SUBSYS controller
clk: sophgo: Avoid -Wsometimes-uninitialized in sg2042_clk_pll_set_rate()
clk/sophgo: Using BUG() instead of unreachable() in mmux_get_parent_id()
clk: mxs: Use clamp() in clk_ref_round_rate() and clk_ref_set_rate()
clk: sunxi-ng r40: Constify struct regmap_config
clk: en7523: fix rate divider for slic and spi clocks
clk: lpc32xx: Constify struct regmap_config
clk: xilinx: Constify struct regmap_config
clk: en7523: Remove PCIe reset open drain configuration for EN7581
clk: en7523: Remove pcie prepare/unpreare callbacks for EN7581 SoC
clk: en7523: Add reset-controller support for EN7581 SoC
dt-bindings: clock: airoha: Add reset support to EN7581 clock binding
dt-bindings: clock: mediatek: Document reset cells for MT8188 sys
clk: mediatek: mt8173-infracfg: Handle unallocated infracfg when module
dt-bindings: clock: mediatek: add syscon compatible for mt7622 pciesys
dt-bindings: clock: sprd,sc9860-clk: convert to YAML
dt-bindings: clock: qoriq-clock: convert to yaml format
clk: qcom: Park shared RCGs upon registration
clk: qcom: ipq9574: Use icc-clk for enabling NoC related clocks
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu updates from Will Deacon:
"Core:
- Support for the "ats-supported" device-tree property
- Removal of the 'ops' field from 'struct iommu_fwspec'
- Introduction of iommu_paging_domain_alloc() and partial conversion
of existing users
- Introduce 'struct iommu_attach_handle' and provide corresponding
IOMMU interfaces which will be used by the IOMMUFD subsystem
- Remove stale documentation
- Add missing MODULE_DESCRIPTION() macro
- Misc cleanups
Allwinner Sun50i:
- Ensure bypass mode is disabled on H616 SoCs
- Ensure page-tables are allocated below 4GiB for the 32-bit
page-table walker
- Add new device-tree compatible strings
AMD Vi:
- Use try_cmpxchg64() instead of cmpxchg64() when updating pte
Arm SMMUv2:
- Print much more useful information on context faults
- Fix Qualcomm TBU probing when CONFIG_ARM_SMMU_QCOM_DEBUG=n
- Add new Qualcomm device-tree bindings
Arm SMMUv3:
- Support for hardware update of access/dirty bits and reporting via
IOMMUFD
- More driver rework from Jason, this time updating the PASID/SVA
support to prepare for full IOMMUFD support
- Add missing MODULE_DESCRIPTION() macro
- Minor fixes and cleanups
NVIDIA Tegra:
- Fix for benign fwspec initialisation issue exposed by rework on the
core branch
Intel VT-d:
- Use try_cmpxchg64() instead of cmpxchg64() when updating pte
- Use READ_ONCE() to read volatile descriptor status
- Remove support for handling Execute-Requested requests
- Avoid calling iommu_domain_alloc()
- Minor fixes and refactoring
Qualcomm MSM:
- Updates to the device-tree bindings"
* tag 'iommu-updates-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: (72 commits)
iommu/tegra-smmu: Pass correct fwnode to iommu_fwspec_init()
iommu/vt-d: Fix identity map bounds in si_domain_init()
iommu: Move IOMMU_DIRTY_NO_CLEAR define
dt-bindings: iommu: Convert msm,iommu-v0 to yaml
iommu/vt-d: Fix aligned pages in calculate_psi_aligned_address()
iommu/vt-d: Limit max address mask to MAX_AGAW_PFN_WIDTH
docs: iommu: Remove outdated Documentation/userspace-api/iommu.rst
arm64: dts: fvp: Enable PCIe ATS for Base RevC FVP
iommu/of: Support ats-supported device-tree property
dt-bindings: PCI: generic: Add ats-supported property
iommu: Remove iommu_fwspec ops
OF: Simplify of_iommu_configure()
ACPI: Retire acpi_iommu_fwspec_ops()
iommu: Resolve fwspec ops automatically
iommu/mediatek-v1: Clean up redundant fwspec checks
RDMA/usnic: Use iommu_paging_domain_alloc()
wifi: ath11k: Use iommu_paging_domain_alloc()
wifi: ath10k: Use iommu_paging_domain_alloc()
drm/msm: Use iommu_paging_domain_alloc()
vhost-vdpa: Use iommu_paging_domain_alloc()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto update from Herbert Xu:
"API:
- Test setkey in no-SIMD context
- Add skcipher speed test for user-specified algorithm
Algorithms:
- Add x25519 support on ppc64le
- Add VAES and AVX512 / AVX10 optimized AES-GCM on x86
- Remove sm2 algorithm
Drivers:
- Add Allwinner H616 support to sun8i-ce
- Use DMA in stm32
- Add Exynos850 hwrng support to exynos"
* tag 'v6.11-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (81 commits)
hwrng: core - remove (un)register_miscdev()
crypto: lib/mpi - delete unnecessary condition
crypto: testmgr - generate power-of-2 lengths more often
crypto: mxs-dcp - Ensure payload is zero when using key slot
hwrng: Kconfig - Do not enable by default CN10K driver
crypto: starfive - Fix nent assignment in rsa dec
crypto: starfive - Align rsa input data to 32-bit
crypto: qat - fix unintentional re-enabling of error interrupts
crypto: qat - extend scope of lock in adf_cfg_add_key_value_param()
Documentation: qat: fix auto_reset attribute details
crypto: sun8i-ce - add Allwinner H616 support
crypto: sun8i-ce - wrap accesses to descriptor address fields
dt-bindings: crypto: sun8i-ce: Add compatible for H616
hwrng: core - Fix wrong quality calculation at hw rng registration
hwrng: exynos - Enable Exynos850 support
hwrng: exynos - Add SMC based TRNG operation
hwrng: exynos - Implement bus clock control
hwrng: exynos - Use devm_clk_get_enabled() to get the clock
hwrng: exynos - Improve coding style
dt-bindings: rng: Add Exynos850 support to exynos-trng
...
|
|
- Use devm_clk_bulk_get_all() to get all the clocks from DT to avoid
writing out all the clock names (Manivannan Sadhasivam)
- Add DT binding and driver support for the SA8775P SoC (Mrinmay Sarkar)
- Refactor dw_pcie_edma_find_chip() to enable adding support for Hyper DMA
(HDMA) (Manivannan Sadhasivam)
- Enable drivers to supply the eDMA channel count since some can't auto
detect this (Manivannan Sadhasivam)
- Add HDMA support for the SA8775P SoC (Mrinmay Sarkar)
- Override the SA8775P NO_SNOOP default to avoid possible memory corruption
(Mrinmay Sarkar)
- Make sure resources are disabled during PERST# assertion, even if the
link is already disabled (Manivannan Sadhasivam)
- Vote for the CPU-PCIe ICC (interconnect) path to ensure it stays active
even if other drivers don't vote for it (Krishna chaitanya chundru)
- Add Operating Performance Points (OPP) to scale performance state based
on aggregate link bandwidth to improve SoC power efficiency (Krishna
chaitanya chundru)
- Return failure instead of success if dev_pm_opp_find_freq_floor() fails
(Dan Carpenter)
- Avoid an error pointer dereference if dev_pm_opp_find_freq_exact() fails
(Dan Carpenter)
- Prevent use of uninitialized data in qcom_pcie_suspend_noirq() (Dan
Carpenter)
* pci/controller/qcom:
PCI: qcom: Prevent use of uninitialized data in qcom_pcie_suspend_noirq()
PCI: qcom: Prevent potential error pointer dereference
PCI: qcom: Fix missing error code in qcom_pcie_probe()
PCI: qcom: Add OPP support to scale performance
PCI: Bring the PCIe speed to MBps logic to new pcie_dev_speed_mbps()
PCI: qcom: Add ICC bandwidth vote for CPU to PCIe path
PCI: qcom-ep: Disable resources unconditionally during PERST# assert
PCI: qcom-ep: Override NO_SNOOP attribute for SA8775P EP
PCI: qcom: Override NO_SNOOP attribute for SA8775P RC
PCI: epf-mhi: Enable HDMA for SA8775P SoC
PCI: qcom-ep: Add HDMA support for SA8775P SoC
PCI: dwc: Pass the eDMA mapping format flag directly from glue drivers
PCI: dwc: Skip finding eDMA channels count for HDMA platforms
PCI: dwc: Refactor dw_pcie_edma_find_chip() API
PCI: qcom-ep: Add support for SA8775P SOC
dt-bindings: PCI: qcom-ep: Add support for SA8775P SoC
PCI: qcom: Use devm_clk_bulk_get_all() API
|
|
- Move PLDA XpressRICH generic DT binding properties to
plda,xpressrich3-axi-common.yaml where they can be shared across
PLDA-based drivers (Minda Chen)
- Create a drivers/pci/controller/plda/ directory for PLDA-based drivers
and move pcie-microchip-host.c there (Minda Chen)
- Move PLDA generic macros to pcie-plda.h where they can be shared across
drivers (Minda Chen)
- Extract PLDA generic structures from pcie-microchip-host.c, rename them
to be generic, and move them to pcie-plda-host.c where they can be shared
across drivers (Minda Chen)
- Add a .request_event_irq() callback for requesting device-specific
interrupts in addition to PLDA-generic interrupts (Minda Chen)
- Add DT binding and driver for the StarFive JH7110 SoC, based on PLDA IP
(Minda Chen)
* pci/controller/microchip:
PCI: starfive: Add JH7110 PCIe controller
dt-bindings: PCI: Add StarFive JH7110 PCIe controller
PCI: Add PCIE_RESET_CONFIG_DEVICE_WAIT_MS waiting time value
PCI: plda: Pass pci_host_bridge to plda_pcie_setup_iomems()
PCI: plda: Add host init/deinit and map bus functions
PCI: plda: Add event bitmap field to struct plda_pcie_rp
PCI: microchip: Move IRQ functions to pcie-plda-host.c
PCI: microchip: Add event irqchip field to host port and add PLDA irqchip
PCI: microchip: Add get_events() callback and PLDA get_event()
PCI: microchip: Add INTx and MSI event num to struct plda_event
PCI: microchip: Add request_event_irq() callback function
PCI: microchip: Add num_events field to struct plda_pcie_rp
PCI: microchip: Rename interrupt related functions
PCI: microchip: Move PLDA functions to pcie-plda-host.c
PCI: microchip: Rename PLDA functions to be generic
PCI: microchip: Move PLDA structures to plda-pcie.h
PCI: microchip: Rename PLDA structures to be generic
PCI: microchip: Add bridge_addr field to struct mc_pcie
PCI: microchip: Move PLDA IP register macros to pcie-plda.h
PCI: microchip: Move pcie-microchip-host.c to PLDA directory
dt-bindings: PCI: Add PLDA XpressRICH PCIe host common properties
# Conflicts:
# drivers/pci/pci.h
|
|
Drop unnecessary blank space from binding documentation.
Reported-by: Pavel Machek <pavel@denx.de>
Closes: https://lore.kernel.org/all/ZpemkYsK6zQgGCF2@duo.ucw.cz/
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240717115649.131914-1-biju.das.jz@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Pull drm updates from Dave Airlie:
"There's a lot of stuff in here, amd, i915 and xe have new platform
work, lots of core rework around EDID handling, some new COMPILE_TEST
options, maintainer changes and a lots of other stuff. Summary:
core:
- deprecate DRM data and return 0 date
- connector: Create a set of helpers to help with HDMI support
- Remove driver owner assignments
- Allow more drivers to compile with COMPILE_TEST
- Conversions to drm_edid
- Sprinkle MODULE_DESCRIPTIONS everywhere they are missing
- Remove drm_mm_replace_node
- print: Add a drm prefix to warn level messages too, remove
___drm_dbg, consolidate prefix handling
- New monochrome TV mode variant
ttm:
- improve number of page faults on some platforms
- fix test builds under PREEMPT_RT
- more test coverage
ci:
- Require a more recent version of mesa
- improve farm setup and test generation
dma-buf:
- warn if reserving 0 fence slots
- internal API heap enhancements
fbdev:
- Create memory manager optimized fbdev emulation
panic:
- Allow to select fonts
- improve drm_fb_dma_get_scanout_buffer
- Allow to dump kmsg to the screen
bridge:
- Remove redundant checks on bridge->encoder
- Remove drm_bridge_chain_mode_fixup
- bridge-connector: Plumb in the new HDMI helper
- analogix_dp: Various improvements, handle AUX transfers timeout
- samsung-dsim: Fix timings calculation
- tc358767: Plenty of small fixes, fix no connector attach, fix
clocks
- sii902x: state validation improvements
panels:
- Switch panels from register table initialization to proper code
- Now that the panel code tracks the panel state, remove every ad-hoc
implementation in the panel drivers
- More cleanup of prepare / enable state tracking in drivers
- edp: Drop legacy panel compatibles
- simple-bridge: Switch to devm_drm_bridge_add
- New panels: Lincoln Tech Sol LCD185-101CT, Microtips Technology
13-101HIEBCAF0-C, Microtips Technology MF-103HIEB0GA0,
BOE nv110wum-l60, IVO t109nw41, WL-355608-A8, PrimeView
PM070WL4, Lincoln Technologies LCD197, Ortustech
COM35H3P70ULC, AUO G104STN01, K&d kd101ne3-40ti
amdgpu:
- DCN 4.0.x support
- GC 12.0 support
- GMC 12.0 support
- SDMA 7.0 support
- MES12 support
- MMHUB 4.1 support
- GFX12 modifier and DCC support
- lots of IP fixes/updates
amdkfd:
- Contiguous VRAM allocations
- GC 12.0 support
- SDMA 7.0 support
- SR-IOV fixes
- KFD GFX ALU exceptions
i915:
- Battlemage Xe2 HPD display enablement
- Panel Replay enabling
- DP AUX-less ALPM/LOBF
- Enable link training failure fallback for DP MST links
- CMRR (Content Match Refresh Rate) enabling
- Increase ADL-S/ADL-P/DG2+ max TMDS bitrate to 6 Gbps
- Enable eDP AUX based HDR backlight
- Support replaying GPU hangs with captured context image
- Automate CCS Mode setting during engine resets
- lots of refactoring
- Support replaying GPU hangs with captured context image
- Increase FLR timeout from 3s to 9s
- Enable w/a 16021333562 for DG2, MTL and ARL [guc]
xe:
- update MAINATINERS
- New uapi adding OA functionality to Xe
- expose l3 bank mask
- fix display detect on ADL-N
- runtime PM Fixes
- Fix silent backmerge issues
- More prep for SR-IOV
- HWmon additions
- per client usage info
- Rework GPU page fault handling
- Drop EXEC_QUEUE_FLAG_BANNED
- Add BMG PCI IDs
- Scheduler fixes and improvements
- Rename xe_exec_queue::compute to xe_exec_queue::lr
- Use ttm_uncached for BO with NEEDS_UC flag
- Rename xe perf layer as xe observation layer
- lots of refactoring
radeon:
- Backlight workaround for iMac
- Silence UBSAN flex array warnings
msm:
- Validate registers XML description against schema in CI
- core/dpu: SM7150 support
- mdp5: Add support for MSM8937
- gpu: Add param for userspace to know if raytracing is supported
- gpu: X185 support (aka gpu in X1 laptop chips)
- gpu: a505 support
ivpu:
- hardware scheduler support
- profiling support
- improvements to the platform support layer
- firmware handling improvements
- clocks/power mgmt improvements
- scheduler/logging improvements
habanalabs:
- Gradual sleep in polling memory macro
- Reduce Gaudi2 MSI-X interrupt count to 128
- Add Gaudi2-D revision support
- Add timestamp to CPLD info
- Gaudi2: Assume hard-reset by firmware upon MC SEI severe error
- Align Gaudi2 interrupt names
- Check for errors after preboot is ready
- Change habanalabs maintainer and git repo path
mgag200:
- refactoring and improvements
- Add BMC output
- enable polling
nouveau:
- add registry command line
v3d:
- perf counters improvements
zynqmp:
- irq and debugfs improvements
atmel-hlcdc:
- Support XLCDC in sam9x7
mipi-dbi:
- Remove mipi_dbi_machine_little_endian
- make SPI bits per word configurable
- support RGB888
- allow pixel formats to be specified in the DT
sun4i:
- Rework the blender setup for DE2
panfrost:
- Enable MT8188 support
vc4:
- Monochrome TV support
exynos:
- fix fallback mode regression
- fix memory leak
- Use drm_edid_duplicate() instead of kmemdup()
etnaviv:
- fix i.MX8MP NPU clock gating
- workaround FE register cdc issues on some cores
- fix DMA sync handling for cached buffers
- fix job timeout handling
- keep TS enabled on MMUv2 cores for improved performance
mediatek:
- Convert to platform remove callback returning void-
- Drop chain_mode_fixup call in mode_valid()
- Fixes the errors of MediaTek display driver found by IGT
- Add display support for the MT8365-EVK board
- Fix bit depth overwritten for mtk_ovl_set bit_depth()
- Fix possible_crtcs calculation
- Fix spurious kfree()
ast:
- refactor mode setting code
stm:
- Add LVDS support
- DSI PHY updates"
* tag 'drm-next-2024-07-18' of https://gitlab.freedesktop.org/drm/kernel: (2501 commits)
drm/amdgpu/mes12: add missing opcode string
drm/amdgpu/mes11: update opcode strings
Revert "drm/amd/display: Reset freesync config before update new state"
drm/omap: Restrict compile testing to PAGE_SIZE less than 64KB
drm/xe: Drop trace_xe_hw_fence_free
drm/xe/uapi: Rename xe perf layer as xe observation layer
drm/amdgpu: remove exp hw support check for gfx12
drm/amdgpu: timely save bad pages to eeprom after gpu ras reset is completed
drm/amdgpu: flush all cached ras bad pages to eeprom
drm/amdgpu: select compute ME engines dynamically
drm/amd/display: Allow display DCC for DCN401
drm/amdgpu: select compute ME engines dynamically
drm/amdgpu/job: Replace DRM_INFO/ERROR logging
drm/amdgpu: select compute ME engines dynamically
drm/amd/pm: Ignore initial value in smu response register
drm/amdgpu: Initialize VF partition mode
drm/amd/amdgpu: fix SDMA IRQ client ID <-> req mapping
MAINTAINERS: fix Xinhui's name
MAINTAINERS: update powerplay and swsmu
drm/qxl: Pin buffer objects for internal mappings
...
|
|
When Maxime originally added the BH2228FV to the spidev driver, he spelt
it incorrectly - the d should have been a b. That spelling was then
propagated to the binding when written by Krzysztof. Add a new, correctly
spelt compatible and advise against using the incorrectly spelling.
Fixes: 025aea27732d ("dt-bindings: trivial-devices: document SPI dev compatibles")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20240717-exuberant-enlighten-f890fabcd247@spud
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- New sensor drivers: gc05a2, gc08a3 and imx283
- New serializer/deserializer drivers: max96714 and max96717
- New JPEG encoder driver: e5010
- Support for Raspberry Pi PiSP Backend (BE) ISP driver
- Old documentation for av7110 driver removed, as a new version was
added as Documentation/userspace-api/media/dvb/legacy*.rst
- atompisp: Linux firmwares are now available, so drop firmware-related
task from TODO and update firmware logic
- The imx258 driver has gained several improvements
- wave5 driver has gained support for HEVC decoding
- em28xx gained support for MyGica UTV3
- av7110 budget-patch driver removed
- Lots of other cleanups, improvements and fixes
* tag 'media/v6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (301 commits)
media: raspberrypi: Switch to remove_new
media: uapi: pisp_be_config: Add extra config fields
media: uapi: pisp_be_config: Re-sort pisp_be_tiles_config
media: uapi: pisp_common: Capitalize all macros
media: uapi: pisp_common: Add 32 bpp format test
media: uapi: pisp_be_config: Drop BIT() from uAPI
media: stm32: dcmipp: correct error handling in dcmipp_create_subdevs
media: atomisp: Fix spelling mistakes in sh_css_sp.c
media: atomisp: Fix spelling mistake in ia_css_debug.c
media: atomisp: Fix spelling mistake in hmm_bo.c
media: atomisp: Fix spelling mistake in ia_css_eed1_8.host.c
media: atomisp: Fix spelling mistake in sh_css_internal.h
media: atomisp: Fix spelling mistake "pipline" -> "pipeline"
media: atomisp: Remove unused GPIO related defines and APIs
media: atomisp: Replace COMPILATION_ERROR_IF() by static_assert()
media: atomisp: Clean up unused macros from math_support.h
media: atomisp: csi2-bridge: Add DMI quirk for OV5693 on Xiaomi Mipad2
media: atomisp: Update TODO
media: atomisp: Prefix firmware paths with "intel/ipu/"
media: atomisp: Remove firmware_name module parameter
...
|