| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Rockchip platforms use 'GPIO_ACTIVE_HIGH' flag in the devicetree definition
for ep_gpio. This means, whatever the logical value set by the driver for
the ep_gpio, physical line will output the same logic level.
For instance,
gpiod_set_value_cansleep(rockchip->ep_gpio, 0); --> Level low
gpiod_set_value_cansleep(rockchip->ep_gpio, 1); --> Level high
But while requesting the ep_gpio, GPIOD_OUT_HIGH flag is currently used.
Now, this also causes the physical line to output 'high' creating trouble
for endpoint devices during host reboot.
When host reboot happens, the ep_gpio will initially output 'low' due to
the GPIO getting reset to its POR value. Then during host controller probe,
it will output 'high' due to GPIOD_OUT_HIGH flag. Then during
rockchip_pcie_host_init_port(), it will first output 'low' and then 'high'
indicating the completion of controller initialization.
On the endpoint side, each output 'low' of ep_gpio is accounted for PERST#
assert and 'high' for PERST# deassert. With the above mentioned flow during
host reboot, endpoint will witness below state changes for PERST#:
(1) PERST# assert - GPIO POR state
(2) PERST# deassert - GPIOD_OUT_HIGH while requesting GPIO
(3) PERST# assert - rockchip_pcie_host_init_port()
(4) PERST# deassert - rockchip_pcie_host_init_port()
Now the time interval between (2) and (3) is very short as both happen
during the driver probe(), and this results in a race in the endpoint.
Because, before completing the PERST# deassertion in (2), endpoint got
another PERST# assert in (3).
A proper way to fix this issue is to change the GPIOD_OUT_HIGH flag in (2)
to GPIOD_OUT_LOW. Because the usual convention is to request the GPIO with
a state corresponding to its 'initial/default' value and let the driver
change the state of the GPIO when required.
As per that, the ep_gpio should be requested with GPIOD_OUT_LOW as it
corresponds to the POR value of '0' (PERST# assert in the endpoint). Then
the driver can change the state of the ep_gpio later in
rockchip_pcie_host_init_port() as per the initialization sequence.
This fixes the firmware crash issue in Qcom based modems connected to
Rockpro64 based board.
Fixes: e77f847df54c ("PCI: rockchip: Add Rockchip PCIe controller support")
Closes: https://lore.kernel.org/mhi/20240402045647.GG2933@thinkpad/
Link: https://lore.kernel.org/linux-pci/[email protected]
Reported-by: Slark Xiao <[email protected]>
Signed-off-by: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Niklas Cassel <[email protected]>
Cc: [email protected] # v4.9
|
|
PCIe r6.0, sec 6.6.1, states that the host should wait for at least 100
msec from the end of a conventional reset (PERST# is de-asserted) before
sending a configuration request to ensure that the device is able to
respond with a "Request Retry Status" completion.
Add the PCIE_T_RRS_READY_MS macro to define this wait time and modify
rockchip_pcie_host_init_port() to add this 100ms sleep after deasserting
PERST# using the ep_gpio GPIO.
Link: https://lore.kernel.org/linux-pci/[email protected]
Suggested-by: Bjorn Helgaas <[email protected]>
Signed-off-by: Damien Le Moal <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
|
|
PCIe CEM r5.1, sec 2.9.2, mandates that the PERST# signal must remain
asserted for at least 100 usec (Tperst-clk) after the PCIe reference clock
becomes stable (if a reference clock is supplied), and for at least 100
msec after the power is stable (Tpvperl, defined by the macro
PCIE_T_PVPERL_MS).
Modify rockchip_pcie_host_init_port() to satisfy these constraints by
adding a sleep period before deasserting PERST# using the ep_gpio GPIO.
Since Tperst-clk is the shorter wait time, add an msleep() call for the
longer PCIE_T_PVPERL_MS milliseconds to handle both timing requirements.
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Damien Le Moal <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
|
|
From the DWC EP databook 5.96a, section "3.5.7.1.4 General Rules for BAR
Setup (Fixed Mask or Programmable Mask Schemes Only)":
"Any pair (for example BARs 0 and 1) can be configured as one 64-bit BAR,
two 32-bit BARs, or one 32-bit BAR."
"BAR pairs cannot overlap to form a 64-bit BAR. For example, you cannot
combine BARs 1 and 2 to form a 64-bit BAR."
While this limitation does exist in some other PCI endpoint controllers,
e.g. cdns_pcie_ep_set_bar(), the limitation does not appear to be defined
in the PCIe specification itself, thus add an explicit check for this in
dw_pcie_ep_set_bar() (rather than pci_epc_set_bar()).
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Niklas Cassel <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
|
|
Down event
Now that dw_pcie_ep_linkdown() is available, use it. This also handles the
reinitialization of DWC non-sticky registers in addition to sending the
notification to EPF drivers.
Closes: https://lore.kernel.org/linux-pci/20240528195539.GA458945@bhelgaas
Link: https://lore.kernel.org/linux-pci/[email protected]
Reported-by: Bjorn Helgaas <[email protected]>
Signed-off-by: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Frank Li <[email protected]>
Reviewed-by: Niklas Cassel <[email protected]>
|
|
event
Now that the generic dw_pcie_ep_linkdown() API is available, use it. This
also handles the reinitialization of DWC non-sticky registers in addition
to sending the notification to EPF drivers.
Link: https://lore.kernel.org/linux-pci/[email protected]
Tested-by: Niklas Cassel <[email protected]>
Signed-off-by: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Niklas Cassel <[email protected]>
|
|
Currently dw_pcie_ep_init_notify() wrapper just calls pci_epc_init_notify()
directly, so this wrapper provides no benefit to the glue drivers.
Remove it and call pci_epc_init_notify() directly from glue drivers.
Suggested-by: Bjorn Helgaas <[email protected]>
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Siddharth Vadapalli <[email protected]>
Reviewed-by: Frank Li <[email protected]>
Reviewed-by: Niklas Cassel <[email protected]>
|
|
Per PCIe r6.0, sec 5.2, a Link Down event can happen under any of the
following circumstances:
1. Fundamental/Hot reset
2. Link disable transmission by upstream component
3. Moving from L2/L3 to L0
In those cases, Link Down causes some non-sticky DWC registers to lose the
state (like REBAR, etc.), so drivers need to reinitialize them to function
properly once the link comes back again.
This is not a problem for drivers supporting PERST# IRQ, since they can
reinitialize the registers in the PERST# IRQ callback. But for the drivers
not supporting PERST#, there is no way they can reinitialize the registers
other than relying on Link Down IRQ received when the link goes down. So
add a DWC generic API dw_pcie_ep_linkdown() that reinitializes the
non-sticky registers and also notifies the EPF drivers about link going
down.
This API can also be used by the drivers supporting PERST# to handle the
scenario (2) mentioned above.
NOTE: For the sake of code organization, move the dw_pcie_ep_linkup()
definition just above dw_pcie_ep_linkdown().
Link: https://lore.kernel.org/linux-pci/[email protected]
Tested-by: Niklas Cassel <[email protected]>
Signed-off-by: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
[bhelgaas: update spec citation]
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Niklas Cassel <[email protected]>
|
|
suspend
Instead of relying on the vendor specific implementations to send the
PME_Turn_Off message, introduce a generic way of sending the message using
the MSG TLP.
This is achieved by reserving a region for MSG TLP of size
'pci->region_align', at the end of the first IORESOURCE_MEM window of the
host bridge. And then sending the PME_Turn_Off message during system
suspend with the help of iATU.
The reason for reserving the MSG TLP region at the end of the
IORESOURCE_MEM is to avoid generating holes in between, because when the
region is allocated using allocate_resource(), memory will be allocated
from the start of the window. Later, if memory gets allocated for an
endpoint of size bigger than 'region_align', there will be a hole between
MSG TLP region and endpoint memory.
This generic implementation is optional for the glue drivers and can be
overridden by a custom 'pme_turn_off' callback.
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
|
|
Add PCIE_MSG_CODE_PME_TURN_OFF macros to enable a PCIe host driver to send
PME_Turn_Off messages.
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
|
|
Add "Message Routing" and "INTx Mechanism Messages" macros to enable
a PCIe driver to send messages for INTx Interrupt Signaling.
Values from PCIe r6.1, sec 2.2.8 and 2.2.8.1.
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Reviewed-by: Serge Semin <[email protected]>
|
|
Add "code" and "routing" into struct dw_pcie_ob_atu_cfg for triggering
INTx IRQs by iATU in the PCIe endpoint mode in near the future.
PCIE_ATU_INHIBIT_PAYLOAD is set to issue TLP type of Msg instead of
MsgD. This implementation supports the data-less messages only for now.
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Reviewed-by: Serge Semin <[email protected]>
|
|
This is a preparation before adding the Msg-type outbound iATU
mapping. The respective update will require two more arguments added
to __dw_pcie_prog_outbound_atu(). That will make the already
complicated function prototype even more hard to comprehend accepting
_eight_ arguments.
To prevent that and keep the code more-or-less readable, move all the
outbound iATU-related arguments to a new config structure: struct
dw_pcie_ob_atu_cfg, and pass a pointer to dw_pcie_prog_outbound_atu(). The
structure should be locally defined and populated with the outbound iATU
settings implied by the caller context.
As a result of this change there is no longer need in having the two
distinctive methods for the Host and Endpoint outbound iATU setups since
the code can directly call the dw_pcie_prog_outbound_atu() method with the
config structure populated, so drop dw_pcie_prog_ep_outbound_atu().
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Reviewed-by: Serge Semin <[email protected]>
|
|
When PERST# assert and deassert happens on the PERST# supported platforms,
both iATU0 and iATU6 will map inbound window to BAR0. DMA will access the
area that was previously allocated (iATU0) for BAR0, instead of the new
area (iATU6) for BAR0.
Right now, this isn't an issue because both iATU0 and iATU6 should
translate inbound accesses to BAR0 to the same allocated memory area.
However, having two separate inbound mappings for the same BAR is a
disaster waiting to happen.
The mappings between PCI BAR and iATU inbound window are maintained in the
dw_pcie_ep::bar_to_atu[] array. While allocating a new inbound iATU map for
a BAR, dw_pcie_ep_inbound_atu() API checks for the availability of the
existing mapping in the array and if it is not found (i.e., value in the
array indexed by the BAR is found to be 0), it allocates a new map value
using find_first_zero_bit().
The issue is the existing logic failed to consider the fact that the map
value '0' is a valid value for BAR0, so find_first_zero_bit() will return
'0' as the map value for BAR0 (note that it returns the first zero bit
position).
Due to this, when PERST# assert + deassert happens on the PERST# supported
platforms, the inbound window allocation restarts from BAR0 and the
existing logic to find the BAR mapping will return '6' for BAR0 instead of
'0' due to the fact that it considers '0' as an invalid map value.
Fix this issue by always incrementing the map value before assigning to
bar_to_atu[] array and then decrementing it while fetching. This will make
sure that the map value '0' always represents the invalid mapping."
Fixes: 4284c88fff0e ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Closes: https://lore.kernel.org/linux-pci/ZXsRp+Lzg3x%2Fnhk3@x1-carbon/
Link: https://lore.kernel.org/linux-pci/[email protected]
Reported-by: Niklas Cassel <[email protected]>
Tested-by: Niklas Cassel <[email protected]>
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Reviewed-by: Niklas Cassel <[email protected]>
|
|
According to [1], msleep should be used for large sleeps, such as the
100-ish ms one in this function. Comply with the guide and use it.
[1] https://docs.kernel.org/timers/timers-howto.html
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Konrad Dybcio <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Johan Hovold <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
|
|
With commit 5779dd0a7dbd7 ("PCI: endpoint: Use notification chain mechanism
to notify EPC events to EPF") the linkup callback has been removed and
replaced by EPC event notifications.
With commit 256ae475201b1 ("PCI: endpoint: Add pci_epf_ops to expose
function-specific attrs") a new (optional) add_cfs callback was added.
Update documentation accordingly.
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Alexander Stein <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Niklas Cassel <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
|
|
functions
These two functions are defined in the pci_endpoint_test.c file, but not
called elsewhere, so delete these unused functions.
This fixes the following warning:
drivers/misc/pci_endpoint_test.c:144:19: warning: unused function 'pci_endpoint_test_bar_readl'.
drivers/misc/pci_endpoint_test.c:150:20: warning: unused function 'pci_endpoint_test_bar_writel'.
No functional changes intended.
[kwilczynski: commit log]
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=9064
Link: https://lore.kernel.org/linux-pci/[email protected]
Reported-by: Abaci Robot <[email protected]>
Signed-off-by: Jiapeng Chong <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
Add a comment suggesting that if the endpoint controller Vendor and Device
ID are programmable, an existing entry might be usable for testing without
having to add an entry to pci_endpoint_test_tbl[].
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Reviewed-by: Frank Li <[email protected]>
|
|
dma_set_mask_and_coherent() should never fail when the mask is >= 32bit,
unless the architecture has no DMA support. So no need to check for the
error and also no need to set dma_set_mask_and_coherent(32) as a fallback.
Even if dma_set_mask_and_coherent(48) fails due to the lack of DMA support
(theoretically), then dma_set_mask_and_coherent(32) will also fail for the
same reason. So the fallback doesn't make sense.
Simplify the code by setting the streaming and coherent DMA mask to 48
bits.
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Reviewed-by: Niklas Cassel <[email protected]>
|
|
The current code uses writel()/readl(), which has an implicit memory
barrier for every single readl()/writel().
Additionally, reading 4 bytes at a time over the PCI bus is not really
optimal, considering that this code is running in an ioctl handler.
Use memcpy_toio()/memcpy_fromio() for BAR tests.
Before patch with a 4MB BAR:
$ time /usr/bin/pcitest -b 1
BAR1: OKAY
real 0m 1.56s
After patch with a 4MB BAR:
$ time /usr/bin/pcitest -b 1
BAR1: OKAY
real 0m 0.54s
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Niklas Cassel <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Reviewed-by: Kuppuswamy Sathyanarayanan <[email protected]>
|
|
Rockchip rk3588 requires 64KB alignment for BARs.
While there is an existing device_id:vendor_id in the driver with 64KB
alignment, that device_id:vendor_id is am654, which uses BAR2 instead of
BAR0 as the test_reg_bar, and also has special is_am654_pci_dev() checks
in the driver to disallow BAR0. In order to allow testing all BARs, add a
new rk3588 entry in the driver.
We intentionally do not add the vendor id to pci_ids.h, since the policy
for that file is that the vendor id has to be used by multiple drivers.
Hopefully, this new entry will be short-lived, as there is a series on the
mailing list which intends to move the address alignment restrictions from
this driver to the endpoint side.
Add a new entry for rk3588 in order to allow us to test all BARs.
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Niklas Cassel <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
|
|
The of_gpio.h legacy API is going to be removed. In preparation for that,
convert the driver to the agnostic API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Andy Shevchenko <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
|
|
Adding support for G761 included adding support for an internal clock.
Enabling the internal clock requires setting a bit in the FAN_CMD2
register. This is implemented in g762_fan_init(). However, g762_fan_init()
is called before clock support is selected, and the flag indicating that
the internal clock should be used is not yet set.
Initialize the clock before initializing the fan to solve the problem.
While at it, also add "g7621" to the i2c_device_id array.
Cc: Christian Marangi <[email protected]>
Fixes: 6ce402327a6f ("hwmon: g672: add support for g761")
Signed-off-by: Guenter Roeck <[email protected]>
|
|
A kernel crash was observed when migrating hugetlb folio:
BUG: kernel NULL pointer dereference, address: 0000000000000008
PGD 0 P4D 0
Oops: Oops: 0002 [#1] PREEMPT SMP NOPTI
CPU: 0 PID: 3435 Comm: bash Not tainted 6.10.0-rc6-00450-g8578ca01f21f #66
RIP: 0010:__folio_undo_large_rmappable+0x70/0xb0
RSP: 0018:ffffb165c98a7b38 EFLAGS: 00000097
RAX: fffffbbc44528090 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffffa30e000a2800 RSI: 0000000000000246 RDI: ffffa3153ffffcc0
RBP: fffffbbc44528000 R08: 0000000000002371 R09: ffffffffbe4e5868
R10: 0000000000000001 R11: 0000000000000001 R12: ffffa3153ffffcc0
R13: fffffbbc44468000 R14: 0000000000000001 R15: 0000000000000001
FS: 00007f5b3a716740(0000) GS:ffffa3151fc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 000000010959a000 CR4: 00000000000006f0
Call Trace:
<TASK>
__folio_migrate_mapping+0x59e/0x950
__migrate_folio.constprop.0+0x5f/0x120
move_to_new_folio+0xfd/0x250
migrate_pages+0x383/0xd70
soft_offline_page+0x2ab/0x7f0
soft_offline_page_store+0x52/0x90
kernfs_fop_write_iter+0x12c/0x1d0
vfs_write+0x380/0x540
ksys_write+0x64/0xe0
do_syscall_64+0xb9/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f5b3a514887
RSP: 002b:00007ffe138fce68 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 000000000000000c RCX: 00007f5b3a514887
RDX: 000000000000000c RSI: 0000556ab809ee10 RDI: 0000000000000001
RBP: 0000556ab809ee10 R08: 00007f5b3a5d1460 R09: 000000007fffffff
R10: 0000000000000000 R11: 0000000000000246 R12: 000000000000000c
R13: 00007f5b3a61b780 R14: 00007f5b3a617600 R15: 00007f5b3a616a00
It's because hugetlb folio is passed to __folio_undo_large_rmappable()
unexpectedly. large_rmappable flag is imperceptibly set to hugetlb folio
since commit f6a8dd98a2ce ("hugetlb: convert alloc_buddy_hugetlb_folio to
use a folio"). Then commit be9581ea8c05 ("mm: fix crashes from deferred
split racing folio migration") makes folio_migrate_mapping() call
folio_undo_large_rmappable() triggering the bug. Fix this issue by
clearing large_rmappable flag for hugetlb folios. They don't need that
flag set anyway.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: f6a8dd98a2ce ("hugetlb: convert alloc_buddy_hugetlb_folio to use a folio")
Fixes: be9581ea8c05 ("mm: fix crashes from deferred split racing folio migration")
Signed-off-by: Miaohe Lin <[email protected]>
Cc: Hugh Dickins <[email protected]>
Cc: Matthew Wilcox (Oracle) <[email protected]>
Cc: Muchun Song <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
There is a potential race between __update_and_free_hugetlb_folio() and
try_memory_failure_hugetlb():
CPU1 CPU2
__update_and_free_hugetlb_folio try_memory_failure_hugetlb
folio_test_hugetlb
-- It's still hugetlb folio.
folio_clear_hugetlb_hwpoison
spin_lock_irq(&hugetlb_lock);
__get_huge_page_for_hwpoison
folio_set_hugetlb_hwpoison
spin_unlock_irq(&hugetlb_lock);
spin_lock_irq(&hugetlb_lock);
__folio_clear_hugetlb(folio);
-- Hugetlb flag is cleared but too late.
spin_unlock_irq(&hugetlb_lock);
When the above race occurs, raw error page info will be leaked. Even
worse, raw error pages won't have hwpoisoned flag set and hit
pcplists/buddy. Fix this issue by deferring
folio_clear_hugetlb_hwpoison() until __folio_clear_hugetlb() is done. So
all raw error pages will have hwpoisoned flag set.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 32c877191e02 ("hugetlb: do not clear hugetlb dtor until allocating vmemmap")
Signed-off-by: Miaohe Lin <[email protected]>
Acked-by: Muchun Song <[email protected]>
Reviewed-by: Oscar Salvador <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
The vmf->ptl in filemap_fault_recheck_pte_none() is still set from
handle_pte_fault(). But at the same time, we did a pte_unmap(vmf->pte).
After a pte_unmap(vmf->pte) unmap and rcu_read_unlock(), the page table
may be racily changed and vmf->ptl maybe fails to protect the actual page
table. Fix this by replacing pte_offset_map() with
pte_offset_map_nolock().
As David said, the PTL pointer might be stale so if we continue to use
it infilemap_fault_recheck_pte_none(), it might trigger UAF. Also, if
the PTL fails, the issue fixed by commit 58f327f2ce80 ("filemap: avoid
unnecessary major faults in filemap_fault()") might reappear.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 58f327f2ce80 ("filemap: avoid unnecessary major faults in filemap_fault()")
Signed-off-by: ZhangPeng <[email protected]>
Suggested-by: David Hildenbrand <[email protected]>
Reviewed-by: David Hildenbrand <[email protected]>
Cc: Aneesh Kumar K.V <[email protected]>
Cc: "Huang, Ying" <[email protected]>
Cc: Hugh Dickins <[email protected]>
Cc: Kefeng Wang <[email protected]>
Cc: Matthew Wilcox (Oracle) <[email protected]>
Cc: Nanyong Sun <[email protected]>
Cc: Yang Shi <[email protected]>
Cc: Yin Fengwei <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
Mark get_current() and current_thread_info() functions as always_inline to
fix the following modpost warning:
WARNING: modpost: vmlinux: section mismatch in reference: get_current+0xc (section: .text.unlikely) -> initcall_level_names (section: .init.data)
The warning happens when these functions are called from an __init
function and they don't get inlined (remain in the .text section) while
the value they return points into .init.data section. Assuming
get_current() always returns a valid address, this situation can happen
only during init stage and accessing .init.data from .text section during
that stage should pose no issues.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 22d407b164ff ("lib: add allocation tagging support for memory allocation profiling")
Signed-off-by: Suren Baghdasaryan <[email protected]>
Cc: Kent Overstreet <[email protected]>
Cc: Chris Zankel <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Juri Lelli <[email protected]>
Cc: Max Filippov <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Suren Baghdasaryan <[email protected]>
Cc: Vincent Guittot <[email protected]>
Cc: kernel test robot <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
Mark alloc_tag_{save|restore} as always_inline to fix the following
modpost warnings:
WARNING: modpost: vmlinux: section mismatch in reference: alloc_tag_save+0x1c (section: .text.unlikely) -> initcall_level_names (section: .init.data)
WARNING: modpost: vmlinux: section mismatch in reference: alloc_tag_restore+0x3c (section: .text.unlikely) -> initcall_level_names (section: .init.data)
The warnings happen when these functions are called from an __init
function and they don't get inlined (remain in the .text section) while
the value returned by get_current() points into .init.data section.
Assuming get_current() always returns a valid address, this situation can
happen only during init stage and accessing .init.data from .text section
during that stage should pose no issues.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 22d407b164ff ("lib: add allocation tagging support for memory allocation profiling")
Signed-off-by: Suren Baghdasaryan <[email protected]>
Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Cc: Kent Overstreet <[email protected]>
Cc: Chris Zankel <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Juri Lelli <[email protected]>
Cc: Max Filippov <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Vincent Guittot <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
Convert loops in kirin_pcie_parse_port() to use the _scoped() version of
for_each_available_child_of_node() so the refcounts of children are
implicitly decremented when the loop is exited.
No functional change intended here, but it will make future error exits
from these loops easier.
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Javier Carrasco <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
[bhelgaas: move to GPIO series to avoid bisection hole, commit log]
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Reviewed-by: Jonathan Cameron <[email protected]>
|
|
When a running task is migrated to another CPU, the stop_task is used to
preempt the running task and migrate it. This, expectedly, invokes
ops.cpu_release(). If the BPF scheduler then calls
scx_bpf_reenqueue_local(), it re-enqueues all tasks on the local DSQ
including the task which is being migrated.
This creates an unnecessary re-enqueue of a task which is about to be
deactivated and re-activated for migration anyway. It can also cause
confusion for the BPF scheduler as scx_bpf_task_cpu() of the task and its
allowed CPUs may not agree while migration is pending.
Signed-off-by: Tejun Heo <[email protected]>
Fixes: 245254f7081d ("sched_ext: Implement sched_ext_ops.cpu_acquire/release()")
Acked-by: David Vernet <[email protected]>
|
|
scx_bpf_reenqueue_local() is used to re-enqueue tasks on the local DSQ from
ops.cpu_release(). Because the BPF scheduler may dispatch tasks to the same
local DSQ, to avoid processing the same tasks repeatedly, it first takes the
number of queued tasks and processes the task at the head of the queue that
number of times.
This is incorrect as a task can be dispatched to the same local DSQ with
SCX_ENQ_HEAD. Such a task will be processed repeatedly until the count is
exhausted and the succeeding tasks won't be processed at all.
Fix it by first moving all candidate tasks to a private list and then
processing that list. While at it, remove the WARNs. They're rather
superflous as later steps will check them anyway.
Signed-off-by: Tejun Heo <[email protected]>
Fixes: 245254f7081d ("sched_ext: Implement sched_ext_ops.cpu_acquire/release()")
Acked-by: David Vernet <[email protected]>
|
|
This adds the following commits from upstream:
1df7b047fe43 pylibfdt/Makefile.pylibfdt: use project's flags to compile the extension
61e88fdcec52 libfdt: overlay: Fix phandle overwrite check for new subtrees
49d30894466e meson: fix installation with meson-python
d54aaf93673c pylibfdt: clean up python build directory
ab86f1e9fda8 pylibfdt: add VERSION.txt to Python sdist
7b8a30eceabe pylibfdt: fix Python version
ff4f17eb5865 pylibfdt/Makefile.pylibfdt: fix Python library being rebuild during install
9e313b14e684 pylibfdt/meson.build: fix Python library being rebuilt during install
d598fc3648ec tests/run_tests.sh: fix Meson library path being dropped
b98239da2f18 tests/meson.build: fix python and yaml tests not running
c17d76ab5e84 checks: Check the overall length of "interrupt-map"
ae26223a056e libfdt: overlay: Refactor overlay_fixup_phandle
4dd831affd01 libfdt: tests: Update test case for overlay_bad_fixup
e6d294200837 tests: Remove two_roots and named_root from LIBTREE_TESTS_L and add all dtb filenames generated by dumptrees to TESTS_TREES_L in Makefile.tests
855c934e26ae tests: fix tests broken under Meson
4fd3f4f0a95d github: enforce testing pylibfdt and yaml support
9ca7d62dbf0b meson: split run-tests by type
bb51223083a4 meson: fix dependencies of tests
e81900635c95 meson: fix pylibfdt missing dependency on libfdt
822123856980 pylibfdt: fix get_mem_rsv for newer Python versions
1fad065080e6 libfdt: overlay: ensure that existing phandles are not overwritten
b0aacd0a7735 github: add windows/msys CI build
ae97d9745862 github: Don't accidentally suppress test errors
057a7dbbb777 github: Display meson test logs on failure
92b5d4e91678 pylibfdt: Remove some apparently deprecated options from setup.py
417e3299dbd1 github: Update to newer checkout action
5e6cefa17e2d fix MinGW format attribute
24f60011fd43 libfdt: Simplify adjustment of values for local fixups
da39ee0e68b6 libfdt: rework shared/static libraries
a669223f7a60 Makefile: do not hardcode the `install` program path
3fbfdd08afd2 libfdt: fix duplicate meson target
dcef5f834ea3 tests: use correct pkg-config when cross compiling
0b8026ff254f meson: allow building from shallow clones
95c74d71f090 treesource: Restore string list output when no type markers
2283dd78eff5 libfdt: fdt_path_offset_namelen: Reject empty path
79b9e326a162 libfdt: fdt_get_alias_namelen: Validate aliases
52157f13ef3d pylibfdt: Support boolean properties
d77433727566 dtc: fix missing string in usage_opts_help
ad8bf9f9aa39 libfdt: Fix fdt_appendprop_addrrange documentation
6c5e189fb952 github: add workflow for Meson builds
a3dc9f006a78 libfdt: rename libfdt-X.Y.Z.so to libfdt.so.X.Y.Z
35019949c4c7 workflows: build: remove setuptools_scm hack
cd3e2304f4a9 pylibfdt: use fallback version in tarballs
0f5864567745 move release version into VERSION.txt
38165954c13b libfdt: add missing version symbols
5e98b5979354 editorconfig: use tab indentation for version.lds
d030a893be25 tests: generate dtbs in Meson build directory
8d8372b13706 tests: fix use of deprecated meson methods
761114effaf7 pylibtfdt: fix use of deprecated meson method
bf6377a98d97 meson: set minimum Meson version to 0.56.0
4c68e4b16b22 libfdt: fix library version to match project version
bdc5c8793a13 meson: allow disabling tests
f088e381f29e Makefile: allow to install libfdt without building executables
6df5328a902c Fix use of <ctype.h> functions
ccf1f62d59ad libfdt: Fix a typo in libfdt.h
71a8b8ef0adf libfdt: meson: Fix linking on macOS linker
589d8c7653c7 dtc: Add an option to generate __local_fixups__ and __fixups__
e8364666d5ac CI: Add build matrix with multiple Linux distributions
3b02a94b486f dtc: Correct invalid dts output with mixed phandles and integers
d4888958d64b tests: Add additional tests for device graph checks
ea3b9a1d2c5a checks: Fix crash in graph_child_address if 'reg' cell size != 1
b2b9671583e9 livetree: fix off-by-one in propval_cell_n() bounds check
ab481e483061 Add definition for a GitHub Actions CI job
c88038c9b8ca Drop obsolete/broken CI definitions
0ac8b30ba5a1 yaml: Depend on libyaml >= 0.2.3
f1657b2fb5be tests: Add test cases for bad endpoint node and remote-endpoint prop checks
44bb89cafd3d checks: Fix segmentation fault in check_graph_node
60bcf1cde1a8 improve documentation for fdt_path_offset()
a6f997bc77d4 add fdt_get_symbol() and fdt_get_symbol_namelen() functions
18f5ec12a10e use fdt_path_getprop_namelen() in fdt_get_alias_namelen()
df093279282c add fdt_path_getprop_namelen() helper
129bb4b78bc6 doc: dt-object-internal: Fix a typo
390f481521c3 fdtoverlay: Drop a a repeated article
9f8b382ed45e manual: Fix and improve documentation about -@
2cdf93a6d402 fdtoverlay: Fix usage string to not mention "<type>"
72fc810c3025 build-sys: add -Wwrite-strings
083ab26da83b tests: fix leaks spotted by ASAN
6f8b28f49609 livetree: fix leak spotted by ASAN
fd68bb8c5658 Make name_node() xstrdup its name argument
4718189c4ca8 Delay xstrdup() of node and property names coming from a flat tree
0b842c3c8199 Make build_property() xstrdup its name argument
9cceabea1ee0 checks: correct I2C 10-bit address check
0d56145938fe yamltree.c: fix -Werror=discarded-qualifiers & -Werror=cast-qual
61fa22b05f69 checks: make check.data const
7a1d72a788e0 checks.c: fix check_msg() leak
ee5799938697 checks.c: fix heap-buffer-overflow
44c9b73801c1 tests: fix -Wwrite-strings
5b60f5104fcc srcpos.c: fix -Wwrite-strings
32174a66efa4 meson: Fix cell overflow tests when running from meson
64a907f08b9b meson.build: bump version to 1.7.0
e3cde0613bfd Add -Wsuggest-attribute=format warning, correct warnings thus generated
41821821101a Use #ifdef NO_VALGRIND
71c19f20b3ef Do not redefine _GNU_SOURCE if already set
039a99414e77 Bump version to v1.7.0
9b62ec84bb2d Merge remote-tracking branch 'gitlab/main'
3f29d6d85c24 pylibfdt: add size_hint parameter for get_path
2022bb10879d checks: Update #{size,address}-cells check for 'dma-ranges'
Signed-off-by: Rob Herring (Arm) <[email protected]>
|
|
QCOM Resource Power Manager-hardened (RPMh) is a hardware block which
maintains hardware state of a regulator by performing max aggregation of
the requests made by all of the clients.
PCIe controller can operate on different RPMh performance state of power
domain based on the speed of the link. And this performance state varies
from target to target, like some controllers support GEN3 in NOM (Nominal)
voltage corner, while some other supports GEN3 in low SVS (static voltage
scaling).
The SoC can be more power efficient if we scale the performance state
based on the aggregate PCIe link bandwidth.
Add Operating Performance Points (OPP) support to vote for RPMh state based
on the aggregate link bandwidth.
OPP can handle ICC bw voting also, so move ICC bw voting through OPP
framework if OPP entries are present.
As we are moving ICC voting as part of OPP, don't initialize ICC if OPP
is supported.
Before PCIe link is initialized vote for highest OPP in the OPP table,
so that we are voting for maximum voltage corner for the link to come up
in maximum supported speed.
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Krishna chaitanya chundru <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
[bhelgaas: wrap comments to fit in 80 columns]
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
|
|
Bring the switch case in pcie_link_speed_mbps() to new function to
the header file so that it can be used in other places like
in controller driver.
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Krishna chaitanya chundru <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
|
|
To access the host controller registers of the host controller and the
endpoint BAR/config space, the CPU-PCIe ICC (interconnect) path should
be voted otherwise it may lead to NoC (Network on chip) timeout.
We are surviving because of other driver voting for this path.
As there is less access on this path compared to PCIe to mem path
add minimum vote i.e 1KBps bandwidth always which is sufficient enough
to keep the path active and is recommended by HW team.
During S2RAM (Suspend-to-RAM), the DBI access can happen very late (while
disabling the boot CPU). So do not disable the CPU-PCIe interconnect path
during S2RAM as that may lead to NoC error.
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Krishna chaitanya chundru <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Bryan O'Donoghue <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
|
|
All EP specific resources are enabled during PERST# deassert. As a counter
operation, all resources should be disabled during PERST# assert. There is
no point in skipping that if the link was not enabled.
This will also result in enablement of the resources twice if PERST# got
deasserted again. So remove the check from qcom_pcie_perst_assert() and
disable all the resources unconditionally.
Fixes: f55fee56a631 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Link: https://lore.kernel.org/linux-pci/[email protected]
Tested-by: Niklas Cassel <[email protected]>
Signed-off-by: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Niklas Cassel <[email protected]>
|
|
Due to some hardware changes, SA8775P has set the NO_SNOOP attribute
in its TLP for all the PCIe controllers. NO_SNOOP attribute when set,
the requester is indicating that no cache coherency issues exist for
the addressed memory on the host i.e., memory is not cached. But in
reality, requester cannot assume this unless there is a complete
control/visibility over the addressed memory on the host.
And worst case, if the memory is cached on the host, it may lead to
memory corruption issues. It should be noted that the caching of memory
on the host is not solely dependent on the NO_SNOOP attribute in TLP.
So to avoid the corruption, this patch overrides the NO_SNOOP attribute
by setting the PCIE_PARF_NO_SNOOP_OVERIDE register. This patch is not
needed for other upstream supported platforms since they do not set
NO_SNOOP attribute by default.
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Mrinmay Sarkar <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
|
|
Due to some hardware changes, SA8775P has set the NO_SNOOP attribute
in its TLP for all the PCIe controllers. NO_SNOOP attribute when set,
the requester is indicating that no cache coherency issue exist for
the addressed memory on the endpoint i.e., memory is not cached. But
in reality, requester cannot assume this unless there is a complete
control/visibility over the addressed memory on the endpoint.
And worst case, if the memory is cached on the endpoint, it may lead to
memory corruption issues. It should be noted that the caching of memory
on the endpoint is not solely dependent on the NO_SNOOP attribute in TLP.
So to avoid the corruption, this patch overrides the NO_SNOOP attribute
by setting the PCIE_PARF_NO_SNOOP_OVERIDE register. This patch is not
needed for other upstream supported platforms since they do not set
NO_SNOOP attribute by default.
8775 has IP version 1.34.0 so introduce a new cfg(cfg_1_34_0) for this
platform. Assign override_no_snoop flag into struct qcom_pcie_cfg and
set it true in cfg_1_34_0 and enable cache snooping if this particular
flag is true.
Link: https://lore.kernel.org/linux-pci/[email protected]
Signed-off-by: Mrinmay Sarkar <[email protected]>
Signed-off-by: Krzysztof Wilczyński <[email protected]>
[bhelgaas: wrap comments to fit in 80 columns]
Signed-off-by: Bjorn Helgaas <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
|
|
Allocate memory, which is being freed at end of the scope, with
scoped/cleanup.h to reduce number of error paths and make code a bit
simpler.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Allocate memory, which is being freed at end of the scope, with
scoped/cleanup.h to reduce number of error paths and make code a bit
simpler.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add documentation for compatible string thead,th1520-i2c which can be
used specifically for the TH1520 SoC.
Signed-off-by: Thomas Bonnefille <[email protected]>
Acked-by: Conor Dooley <[email protected]>
Reviewed-by: Jarkko Nikula <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
A few more Arm64 DeviceTree updates for v6.11
This introduces support for Lenovo Thinkpad Yoga slim 7x, LG Leon LTE,
and LG K10 (K420n).
In addition to this, all Gen-1 platforms gets the DWC3 quirk to disable
"SuperSpeed in park mode", which resolves an instabliity issue seen in
host mode.
For Fairphone 4, PM6150L and PMK8003 thermal sensors are added and
thermal zones defined.
Two fastrpc contexts on SM6350 are marked as non-secure, to allow
non-secure usage.
The video clock controller on SM8150 is introduced. IPQ9574 GCC is
marked as a interconnect provider. The vibrator block in the PM6150 is
described.
On SC7280 the download mode register is defined for SCM, allowing it to
enable/disable the ramdump support during a system crash.
Lastly, add a mailmap entry for Luca Weiss.
* tag 'qcom-arm64-for-6.11-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (22 commits)
mailmap: Update Luca Weiss's email address
arm64: dts: qcom: msm8916-lg-c50: add initial dts for LG Leon LTE
arm64: dts: qcom: msm8916-lg-m216: Add initial device tree
dt-bindings: arm: qcom: Add msm8916 based LG devices
arm64: dts: qcom: ipq9574: Add icc provider ability to gcc
dt-bindings: interconnect: Add Qualcomm IPQ9574 support
arm64: dts: qcom: sm8150: Add video clock controller node
arm64: dts: qcom: pm6150: Add vibrator
arm64: dts: qcom: sc7280: Enable download mode register write
arm64: dts: qcom: sm7225-fairphone-fp4: Add PM6150L thermals
arm64: dts: qcom: sm7225-fairphone-fp4: Add PMK8003 thermals
arm64: dts: qcom: sm6350: Add missing qcom,non-secure-domain property
arm64: dts: qcom: sdm845: Disable SS instance in Parkmode for USB
arm64: dts: qcom: msm8996: Disable SS instance in Parkmode for USB
arm64: dts: qcom: sm6350: Disable SS instance in Parkmode for USB
arm64: dts: qcom: sm6115: Disable SS instance in Parkmode for USB
arm64: dts: qcom: sdm630: Disable SS instance in Parkmode for USB
arm64: dts: qcom: msm8998: Disable SS instance in Parkmode for USB
arm64: dts: qcom: ipq8074: Disable SS instance in Parkmode for USB
arm64: dts: qcom: ipq6018: Disable SS instance in Parkmode for USB
...
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
One more Arm32 DeviceTree update for v6.11
This fixes the DeviceTree validation warning about MSM8960 /memory node
not having a unit address.
* tag 'qcom-arm32-for-6.11-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: msm8960: correct memory base
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Add some time to wait for LP engine to complete its operation
before polling pmctrl register.
Signed-off-by: Michael Lo <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Tested-by: David Ruth <[email protected]>
Acked-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
|
|
Register MLD capability for the firmware supporting MLO.
Co-developed-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/49c796b101e792c84bc2c0d74753022b75fd3355.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <[email protected]>
|
|
remove the unused function mt7925_mcu_set_chan_info
Co-developed-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/0aa0abe7fc661380ae812c6bc879a7705de401b2.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <[email protected]>
|
|
Update band_idx in per-link BSS to be auto for the MLO-enabled firmware
and the MLO-enabled firmware only supports omac index in 0.
The change remains compatible with the non-MLO mode and the older firmware.
Co-developed-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/37fcf3ea7b4883840d61f97231277b297e1b15a3.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <[email protected]>
|
|
update mt7925_mcu_bss_basic_tlv for the MLO-enabled firmware.
The change remains compatible with the non-MLO mode and the
older firmware.
Co-developed-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/583a3ac10583cfef0028f9a0b5a4802fc4070b99.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <[email protected]>
|
|
Set the BSS index from the per-linked BSS for the firmware to identify
which link the command is operating on.
Co-developed-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/dde970c748586d03fbecbccb10cb9903284719aa.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <[email protected]>
|
|
when we serve MLO during the multiple-linked connection, the chanctx may
be not available in the internal driver, we should get the proper the
band information from link_conf for the MLO-enabled firmware.
Co-developed-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/6620e00fbeef686fb2041556deba346411eab0f1.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <[email protected]>
|