| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
mcp2518fd"
Marc Kleine-Budde <[email protected]> says:
This patch series tries to work around erratum DS80000789E 6 of the
mcp2518fd, found by Stefan Althöfer, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value.
For the RX FIDO this caused old, already processed CAN frames or new,
incompletely written CAN frames to be (re-)processed.
To work around this issue, keep a per FIFO timestamp of the last valid
received CAN frame and compare against the timestamp of every received
CAN frame.
Further tests showed that this workaround can recognize old CAN
frames, but a small time window remains in which partially written CAN
frames are not recognized but then processed. These CAN frames have
the correct data and time stamps, but the DLC has not yet been
updated.
For the TEF FIFO the original driver already detects the error, update
the error handling with the knowledge that it is causes by this erratum.
Link: https://lore.kernel.org/all/20240628-mcp251xfd-workaround-erratum-6-v4-0-53586f168524@pengutronix.de
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
This patch updates the workaround for a problem similar to erratum
DS80000789E 6 of the mcp2518fd, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
In the bad case, the driver reads a too large head index. As the FIFO
is implemented as a ring buffer, this results in re-handling old CAN
transmit complete events.
Every transmit complete event contains with a sequence number that
equals to the sequence number of the corresponding TX request. This
way old TX complete events can be detected.
If the original driver detects a non matching sequence number, it
prints an info message and tries again later. As wrong sequence
numbers can be explained by the erratum DS80000789E 6, demote the info
message to debug level, streamline the code and update the comments.
Keep the behavior: If an old CAN TX complete event is detected, abort
the iteration and mark the number of valid CAN TX complete events as
processed in the chip by incrementing the FIFO's tail index.
Cc: Stefan Althöfer <[email protected]>
Cc: Thomas Kopp <[email protected]>
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
This is a preparatory patch to work around a problem similar to
erratum DS80000789E 6 of the mcp2518fd, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
When handling the TEF interrupt, the driver reads the FIFO header
index from the TEF FIFO STA register of the chip.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old CAN transmit complete events that were already processed to be
re-processed.
Instead of reading and trusting the head index, read the head index
and calculate the number of CAN frames that were supposedly received -
replace mcp251xfd_tef_ring_update() with mcp251xfd_get_tef_len().
The mcp251xfd_handle_tefif() function reads the CAN transmit complete
events from the chip, iterates over them and pushes them into the
network stack. The original driver already contains code to detect old
CAN transmit complete events, that will be updated in the next patch.
Cc: Stefan Althöfer <[email protected]>
Cc: Thomas Kopp <[email protected]>
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
This patch tries to works around erratum DS80000789E 6 of the
mcp2518fd, the other variants of the chip family (mcp2517fd and
mcp251863) are probably also affected.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old, already processed CAN frames or new, incompletely written CAN
frames to be (re-)processed.
To work around this issue, keep a per FIFO timestamp [1] of the last
valid received CAN frame and compare against the timestamp of every
received CAN frame. If an old CAN frame is detected, abort the
iteration and mark the number of valid CAN frames as processed in the
chip by incrementing the FIFO's tail index.
Further tests showed that this workaround can recognize old CAN
frames, but a small time window remains in which partially written CAN
frames [2] are not recognized but then processed. These CAN frames
have the correct data and time stamps, but the DLC has not yet been
updated.
[1] As the raw timestamp overflows every 107 seconds (at the usual
clock rate of 40 MHz) convert it to nanoseconds with the
timecounter framework and use this to detect stale CAN frames.
Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com [2]
Reported-by: Stefan Althöfer <[email protected]>
Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM
Tested-by: Stefan Althöfer <[email protected]>
Tested-by: Thomas Kopp <[email protected]>
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
This is a preparatory patch to work around erratum DS80000789E 6 of
the mcp2518fd, the other variants of the chip family (mcp2517fd and
mcp251863) are probably also affected.
When handling the RX interrupt, the driver iterates over all pending
FIFOs (which are implemented as ring buffers in hardware) and reads
the FIFO header index from the RX FIFO STA register of the chip.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old CAN frames that were already processed, or new, incompletely
written CAN frames to be (re-)processed.
Instead of reading and trusting the head index, read the head index
and calculate the number of CAN frames that were supposedly received -
replace mcp251xfd_rx_ring_update() with mcp251xfd_get_rx_len().
The mcp251xfd_handle_rxif_ring() function reads the received CAN
frames from the chip, iterates over them and pushes them into the
network stack. Prepare that the iteration can be stopped if an old CAN
frame is detected. The actual code to detect old or incomplete frames
and abort will be added in the next patch.
Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com
Reported-by: Stefan Althöfer <[email protected]>
Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM
Tested-by: Stefan Althöfer <[email protected]>
Tested-by: Thomas Kopp <[email protected]>
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
function
This is a preparation patch.
Sending the UINC messages followed by incrementing the tail pointer
will be called in more than one place in upcoming patches, so factor
this out into a separate function.
Also make mcp251xfd_handle_rxif_ring_uinc() safe to be called with a
"len" of 0.
Tested-by: Stefan Althöfer <[email protected]>
Tested-by: Thomas Kopp <[email protected]>
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
The mcp251xfd chip is configured to provide a timestamp with each
received and transmitted CAN frame. The timestamp is derived from the
internal free-running timer, which can also be read from the TBC
register via SPI. The timer is 32 bits wide and is clocked by the
external oscillator (typically 20 or 40 MHz).
To avoid confusion, we call this timestamp "timestamp_raw" or "ts_raw"
for short.
Using the timecounter framework, the "ts_raw" is converted to 64 bit
nanoseconds since the epoch. This is what we call "timestamp".
This is a preparation for the next patches which use the "timestamp"
to work around a bug where so far only the "ts_raw" is used.
Tested-by: Stefan Althöfer <[email protected]>
Tested-by: Thomas Kopp <[email protected]>
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
mcp251xfd_chip_start/stop()
The mcp251xfd wakes up from Low Power or Sleep Mode when SPI activity
is detected. To avoid this, make sure that the timestamp worker is
stopped before shutting down the chip.
Split the starting of the timestamp worker out of
mcp251xfd_timestamp_init() into the separate function
mcp251xfd_timestamp_start().
Call mcp251xfd_timestamp_init() before mcp251xfd_chip_start(), move
mcp251xfd_timestamp_start() to mcp251xfd_chip_start(). In this way,
mcp251xfd_timestamp_stop() can be called unconditionally by
mcp251xfd_chip_stop().
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Since the errata references have been added to the driver, new errata
sheets have been published. Update the references for the mcp2517fd
and mcp2518fd. For completeness add references for the mcp251863.
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
To fix the coding style, remove the whitespace in front of labels.
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
The 'profile_pc()' function is used for timer-based profiling, which
isn't really all that relevant any more to begin with, but it also ends
up making assumptions based on the stack layout that aren't necessarily
valid.
Basically, the code tries to account the time spent in spinlocks to the
caller rather than the spinlock, and while I support that as a concept,
it's not worth the code complexity or the KASAN warnings when no serious
profiling is done using timers anyway these days.
And the code really does depend on stack layout that is only true in the
simplest of cases. We've lost the comment at some point (I think when
the 32-bit and 64-bit code was unified), but it used to say:
Assume the lock function has either no stack frame or a copy
of eflags from PUSHF.
which explains why it just blindly loads a word or two straight off the
stack pointer and then takes a minimal look at the values to just check
if they might be eflags or the return pc:
Eflags always has bits 22 and up cleared unlike kernel addresses
but that basic stack layout assumption assumes that there isn't any lock
debugging etc going on that would complicate the code and cause a stack
frame.
It causes KASAN unhappiness reported for years by syzkaller [1] and
others [2].
With no real practical reason for this any more, just remove the code.
Just for historical interest, here's some background commits relating to
this code from 2006:
0cb91a229364 ("i386: Account spinlocks to the caller during profiling for !FP kernels")
31679f38d886 ("Simplify profile_pc on x86-64")
and a code unification from 2009:
ef4512882dbe ("x86: time_32/64.c unify profile_pc")
but the basics of this thing actually goes back to before the git tree.
Link: https://syzkaller.appspot.com/bug?extid=84fe685c02cd112a2ac3 [1]
Link: https://lore.kernel.org/all/CAK55_s7Xyq=nh97=K=G1sxueOFrJDAvPOJAL4TPTCAYvmxO9_A@mail.gmail.com/ [2]
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Allocate and initialize struct ice_adapter object only once per physical
card instead of once per port. This is not a big deal by now, but we want
to extend this struct more and more in the near future. Our plans include
PTP stuff and a devlink instance representing whole-device/physical card.
Transactions requiring to be sleep-able (like those doing user (here ice)
memory allocation) must be performed with an additional (on top of xarray)
mutex. Adding it here removes need to xa_lock() manually.
Since this commit is a reimplementation of ice_adapter_get(), a rather new
scoped_guard() wrapper for locking is used to simplify the logic.
It's worth to mention that xa_insert() use gives us both slot reservation
and checks if it is already filled, what simplifies code a tiny bit.
Reviewed-by: Wojciech Drewek <[email protected]>
Signed-off-by: Przemek Kitszel <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Reviewed-by: Michal Schmidt <[email protected]>
Tested-by: Pucha Himasekhar Reddy <[email protected]> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <[email protected]>
|
|
When clearing registers on new write requests was added, the protection
for currently running commands was missed leading to concurrent access
to the testunit registers. Check the flag beforehand.
Fixes: b39ab96aa894 ("i2c: testunit: add support for block process calls")
Signed-off-by: Wolfram Sang <[email protected]>
Reviewed-by: Andi Shyti <[email protected]>
|
|
STOP fallsthrough to WRITE_REQUESTED but this became problematic when
clearing the testunit registers was added to the latter. Actually, there
is no reason to clear the testunit state after STOP. Doing it when a new
WRITE_REQUESTED arrives is enough. So, no need to fallthrough, at all.
Fixes: b39ab96aa894 ("i2c: testunit: add support for block process calls")
Signed-off-by: Wolfram Sang <[email protected]>
Reviewed-by: Andi Shyti <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current
Fixed a build error following the major refactoring involving the
VIA-I2C modules. Originally, the code was split to group together
parts that would be used by different drivers. This caused build
issues when two modules linked to the same code.
|
|
This fixes the following deadlock introduced by 39a92a55be13
("bluetooth/l2cap: sync sock recv cb and release")
============================================
WARNING: possible recursive locking detected
6.10.0-rc3-g4029dba6b6f1 #6823 Not tainted
--------------------------------------------
kworker/u5:0/35 is trying to acquire lock:
ffff888002ec2510 (&chan->lock#2/1){+.+.}-{3:3}, at:
l2cap_sock_recv_cb+0x44/0x1e0
but task is already holding lock:
ffff888002ec2510 (&chan->lock#2/1){+.+.}-{3:3}, at:
l2cap_get_chan_by_scid+0xaf/0xd0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&chan->lock#2/1);
lock(&chan->lock#2/1);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by kworker/u5:0/35:
#0: ffff888002b8a940 ((wq_completion)hci0#2){+.+.}-{0:0}, at:
process_one_work+0x750/0x930
#1: ffff888002c67dd0 ((work_completion)(&hdev->rx_work)){+.+.}-{0:0},
at: process_one_work+0x44e/0x930
#2: ffff888002ec2510 (&chan->lock#2/1){+.+.}-{3:3}, at:
l2cap_get_chan_by_scid+0xaf/0xd0
To fix the original problem this introduces l2cap_chan_lock at
l2cap_conless_channel to ensure that l2cap_sock_recv_cb is called with
chan->lock held.
Fixes: 89e856e124f9 ("bluetooth/l2cap: sync sock recv cb and release")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Syzbot hit warning in hci_conn_del() caused by freeing handle that was
not allocated using ida allocator.
This is caused by handle bigger than HCI_CONN_HANDLE_MAX passed by
hci_le_big_sync_established_evt(), which makes code think it's unset
connection.
Add same check for handle upper bound as in hci_conn_set_handle() to
prevent warning.
Link: https://syzkaller.appspot.com/bug?extid=b2545b087a01a7319474
Reported-by: [email protected]
Fixes: 181a42edddf5 ("Bluetooth: Make handle of hci_conn be unique")
Signed-off-by: Pavel Skripkin <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
This fixes the following Smatch static checker warning:
net/bluetooth/iso.c:1364 iso_sock_recvmsg()
error: we previously assumed 'pi->conn->hcon' could be null (line 1359)
net/bluetooth/iso.c
1347 static int iso_sock_recvmsg(struct socket *sock, struct msghdr *msg,
1348 size_t len, int flags)
1349 {
1350 struct sock *sk = sock->sk;
1351 struct iso_pinfo *pi = iso_pi(sk);
1352
1353 BT_DBG("sk %p", sk);
1354
1355 if (test_and_clear_bit(BT_SK_DEFER_SETUP,
&bt_sk(sk)->flags)) {
1356 lock_sock(sk);
1357 switch (sk->sk_state) {
1358 case BT_CONNECT2:
1359 if (pi->conn->hcon &&
^^^^^^^^^^^^^^ If ->hcon is NULL
1360 test_bit(HCI_CONN_PA_SYNC,
&pi->conn->hcon->flags)) {
1361 iso_conn_big_sync(sk);
1362 sk->sk_state = BT_LISTEN;
1363 } else {
--> 1364 iso_conn_defer_accept(pi->conn->hcon);
^^^^^^^^^^^^^^
then we're toast
1365 sk->sk_state = BT_CONFIG;
1366 }
1367 release_sock(sk);
1368 return 0;
1369 case BT_CONNECTED:
1370 if (test_bit(BT_SK_PA_SYNC,
Fixes: fbdc4bc47268 ("Bluetooth: ISO: Use defer setup to separate PA sync and BIG sync")
Signed-off-by: Iulia Tanasescu <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
The problem occurs between the system call to close the sock and hci_rx_work,
where the former releases the sock and the latter accesses it without lock protection.
CPU0 CPU1
---- ----
sock_close hci_rx_work
l2cap_sock_release hci_acldata_packet
l2cap_sock_kill l2cap_recv_frame
sk_free l2cap_conless_channel
l2cap_sock_recv_cb
If hci_rx_work processes the data that needs to be received before the sock is
closed, then everything is normal; Otherwise, the work thread may access the
released sock when receiving data.
Add a chan mutex in the rx callback of the sock to achieve synchronization between
the sock release and recv cb.
Sock is dead, so set chan data to NULL, avoid others use invalid sock pointer.
Reported-and-tested-by: [email protected]
Signed-off-by: Edward Adam Davis <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
hci_le_big_sync_established_evt is necessary to filter out cases where the
handle value is belonging to ida id range, otherwise ida will be erroneously
released in hci_conn_cleanup.
Fixes: 181a42edddf5 ("Bluetooth: Make handle of hci_conn be unique")
Reported-by: [email protected]
Closes: https://syzkaller.appspot.com/bug?extid=b2545b087a01a7319474
Signed-off-by: Edward Adam Davis <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
This sets the default power save mode setting to enabled.
The power save feature is now stable and stress test issues, such as the
TX timeout error, have been resolved.
commit c7ee0bc8db32 ("Bluetooth: btnxpuart: Resolve TX timeout error in
power save stress test")
With this setting, the driver will send the vendor command to FW at
startup, to enable power save feature.
User can disable this feature using the following vendor command:
hcitool cmd 3f 23 03 00 00 (HCI_NXP_AUTO_SLEEP_MODE)
Signed-off-by: Neeraj Sanjay Kale <[email protected]>
Reviewed-by: Paul Menzel <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
syzbot is reporting that calling hci_release_dev() from hci_error_reset()
due to hci_dev_put() from hci_error_reset() can cause deadlock at
destroy_workqueue(), for hci_error_reset() is called from
hdev->req_workqueue which destroy_workqueue() needs to flush.
We need to make sure that hdev->{rx_work,cmd_work,tx_work} which are
queued into hdev->workqueue and hdev->{power_on,error_reset} which are
queued into hdev->req_workqueue are no longer running by the moment
destroy_workqueue(hdev->workqueue);
destroy_workqueue(hdev->req_workqueue);
are called from hci_release_dev().
Call cancel_work_sync() on these work items from hci_unregister_dev()
as soon as hdev->list is removed from hci_dev_list.
Reported-by: syzbot <[email protected]>
Closes: https://syzkaller.appspot.com/bug?extid=da0a9c9721e36db712e8
Signed-off-by: Tetsuo Handa <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Commit 272970be3dab ("Bluetooth: hci_qca: Fix driver shutdown on closed
serdev") will cause below regression issue:
BT can't be enabled after below steps:
cold boot -> enable BT -> disable BT -> warm reboot -> BT enable failure
if property enable-gpios is not configured within DT|ACPI for QCA6390.
The commit is to fix a use-after-free issue within qca_serdev_shutdown()
by adding condition to avoid the serdev is flushed or wrote after closed
but also introduces this regression issue regarding above steps since the
VSC is not sent to reset controller during warm reboot.
Fixed by sending the VSC to reset controller within qca_serdev_shutdown()
once BT was ever enabled, and the use-after-free issue is also fixed by
this change since the serdev is still opened before it is flushed or wrote.
Verified by the reported machine Dell XPS 13 9310 laptop over below two
kernel commits:
commit e00fc2700a3f ("Bluetooth: btusb: Fix triggering coredump
implementation for QCA") of bluetooth-next tree.
commit b23d98d46d28 ("Bluetooth: btusb: Fix triggering coredump
implementation for QCA") of linus mainline tree.
Fixes: 272970be3dab ("Bluetooth: hci_qca: Fix driver shutdown on closed serdev")
Cc: [email protected]
Reported-by: Wren Turkal <[email protected]>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218726
Signed-off-by: Zijun Hu <[email protected]>
Tested-by: Wren Turkal <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
qos->ucast interval reffers to the SDU interval, and should not
be set to the interval value reported by the LE CIS Established
event since the latter reffers to the ISO interval. These two
interval are not the same thing:
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 6, Part G
Isochronous interval:
The time between two consecutive BIS or CIS events (designated
ISO_Interval in the Link Layer)
SDU interval:
The nominal time between two consecutive SDUs that are sent or
received by the upper layer.
So this instead uses the following formula from the spec to calculate
the resulting SDU interface:
BLUETOOTH CORE SPECIFICATION Version 5.4 | Vol 6, Part G
page 3075:
Transport_Latency_C_To_P = CIG_Sync_Delay + (FT_C_To_P) ×
ISO_Interval + SDU_Interval_C_To_P
Transport_Latency_P_To_C = CIG_Sync_Delay + (FT_P_To_C) ×
ISO_Interval + SDU_Interval_P_To_C
Link: https://github.com/bluez/bluez/issues/823
Fixes: 2be22f1941d5 ("Bluetooth: hci_event: Fix parsing of CIS Established Event")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
check pdata return of skb_pull_data, instead of data.
Fixes: c2b636b3f788 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Vijay Satija <[email protected]>
Signed-off-by: Kiran K <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
We are releasing a single msgid, so the order argument to
bitmap_release_region must be zero.
Fixes: 8a06127602de ("Bluetooth: hci_bcm4377: Add new driver for BCM4377 PCIe boards")
Cc: [email protected]
Signed-off-by: Hector Martin <[email protected]>
Reviewed-by: Sven Peter <[email protected]>
Reviewed-by: Neal Gompa <[email protected]>
Signed-off-by: Sven Peter <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Some Broadcom controllers found on Apple Silicon machines abuse the
reserved bits inside the PHY fields of LE Extended Advertising Report
events for additional flags. Add a quirk to drop these and correctly
extract the Primary/Secondary_PHY field.
The following excerpt from a btmon trace shows a report received with
"Reserved" for "Primary PHY" on a 4388 controller:
> HCI Event: LE Meta Event (0x3e) plen 26
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x2515
Props: 0x0015
Connectable
Directed
Use legacy advertising PDUs
Data status: Complete
Reserved (0x2500)
Legacy PDU Type: Reserved (0x2515)
Address type: Random (0x01)
Address: 00:00:00:00:00:00 (Static)
Primary PHY: Reserved
Secondary PHY: No packets
SID: no ADI field (0xff)
TX power: 127 dBm
RSSI: -60 dBm (0xc4)
Periodic advertising interval: 0.00 msec (0x0000)
Direct address type: Public (0x00)
Direct address: 00:00:00:00:00:00 (Apple, Inc.)
Data length: 0x00
Cc: [email protected]
Fixes: 2e7ed5f5e69b ("Bluetooth: hci_sync: Use advertised PHYs on hci_le_ext_create_conn_sync")
Reported-by: Janne Grunau <[email protected]>
Closes: https://lore.kernel.org/all/Zjz0atzRhFykROM9@robin
Tested-by: Janne Grunau <[email protected]>
Signed-off-by: Sven Peter <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Admin queue command for shutdown AQ contains a flag to indicate driver
unload. However, the flag is always set in the driver, even for resets. It
can cause the firmware to consider driver as unloaded once the PF reset is
triggered on all ports of device, which could lead to unexpected results.
Add an additional function parameter to functions that shutdown AQ,
indicating whether the driver is actually unloading.
Reviewed-by: Ahmed Zaki <[email protected]>
Reviewed-by: Przemek Kitszel <[email protected]>
Signed-off-by: Piotr Gardocki <[email protected]>
Signed-off-by: Marcin Szycik <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Tested-by: Pucha Himasekhar Reddy <[email protected]> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Allow the driver to be compatible with different FW API versions based
on the device's MAC type. Currently, E810 is only compatible with one
FW API version. Now the driver can be compatible with different FW API
versions for both E810 and E830. For example, E810 FW API version is
1.5.0 and E830 is 1.7.0.
Signed-off-by: Paul Greenwalt <[email protected]>
Tested-by: Pucha Himasekhar Reddy <[email protected]> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Check the return value from ice_vsi_rebuild() and prevent the usage of
incorrectly configured VSI.
Reviewed-by: Michal Swiatkowski <[email protected]>
Reviewed-by: Przemek Kitszel <[email protected]>
Signed-off-by: Eric Joyner <[email protected]>
Signed-off-by: Karen Ostrowska <[email protected]>
Tested-by: Pucha Himasekhar Reddy <[email protected]> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Changing the MAC address of the VFs is currently unsupported via devlink.
Add the function handlers to set and get the HW address for the VFs.
Signed-off-by: Karthik Sundaravel <[email protected]>
Tested-by: Rafal Romanowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Since Jesse has moved to a new role, replace him with a new maintainer
to work with Tony on representing Intel networking drivers in the
kernel.
Cc: Przemek Kitszel <[email protected]>
Signed-off-by: Jesse Brandeburg <[email protected]>
Acked-by: Paul Menzel <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
- Due to a late review, revert and re-fix a recent crasher fix
* tag 'nfsd-6.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
Revert "nfsd: fix oops when reading pool_stats before server is started"
nfsd: initialise nfsd_info.mutex early.
|
|
Pull bcachefs fixes from Kent Overstreet:
"Simple stuff:
- NULL ptr/err ptr deref fixes
- fix for getting wedged on shutdown after journal error
- fix missing recalc_capacity() call, capacity now changes correctly
after a device goes read only
however: our capacity calculation still doesn't take into account
when we have mixed ro/rw devices and the ro devices have data on
them, that's going to be a more involved fix to separate accounting
for "capacity used on ro devices" and "capacity used on rw devices"
- boring syzbot stuff
Slightly more involved:
- discard, invalidate workers are now per device
this has the effect of simplifying how we take device refs in these
paths, and the device ref cleanup fixes a longstanding race between
the device removal path and the discard path
- fixes for how the debugfs code takes refs on btree_trans objects we
have debugfs code that prints in use btree_trans objects.
It uses closure_get() on trans->ref, which is mainly for the cycle
detector, but the debugfs code was using it on a closure that may
have hit 0, which is not allowed; for performance reasons we cannot
avoid having not-in-use transactions on the global list.
Introduce some new primitives to fix this and make the
synchronization here a whole lot saner"
* tag 'bcachefs-2024-06-28' of https://evilpiepirate.org/git/bcachefs:
bcachefs: Fix kmalloc bug in __snapshot_t_mut
bcachefs: Discard, invalidate workers are now per device
bcachefs: Fix shift-out-of-bounds in bch2_blacklist_entries_gc
bcachefs: slab-use-after-free Read in bch2_sb_errors_from_cpu
bcachefs: Add missing bch2_journal_do_writes() call
bcachefs: Fix null ptr deref in journal_pins_to_text()
bcachefs: Add missing recalc_capacity() call
bcachefs: Fix btree_trans list ordering
bcachefs: Fix race between trans_put() and btree_transactions_read()
closures: closure_get_not_zero(), closure_return_sync()
bcachefs: Make btree_deadlock_to_text() clearer
bcachefs: fix seqmutex_relock()
bcachefs: Fix freeing of error pointers
|
|
Pull block fixes from Jens Axboe:
"NVMe fixes via Keith:
- Fabrics fixes (Hannes)
- Missing module description (Jeff)
- Clang warning fix (Nathan)"
* tag 'block-6.10-20240628' of git://git.kernel.dk/linux:
nvmet-fc: Remove __counted_by from nvmet_fc_tgt_queue.fod[]
nvmet: make 'tsas' attribute idempotent for RDMA
nvme: fixup comment for nvme RDMA Provider Type
nvme-apple: add missing MODULE_DESCRIPTION()
nvmet: do not return 'reserved' for empty TSAS values
nvme: fix NVME_NS_DEAC may incorrectly identifying the disk as EXT_LBA.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu fixes from Joerg Roedel:
- Two cache flushing fixes for Intel and AMD drivers
- AMD guest translation enabling fix
- Update IOMMU tree location in MAINTAINERS file
* tag 'iommu-fixes-v6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux:
MAINTAINERS: Update IOMMU tree location
iommu/amd: Fix GT feature enablement again
iommu/vt-d: Fix missed device TLB cache tag
iommu/amd: Invalidate cache before removing device from domain list
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"An assortment of driver fixes and two commits addressing a bad
behavior of the GPIO uAPI when reconfiguring requested lines.
- fix a race condition in i2c transfers by adding a missing i2c lock
section in gpio-pca953x
- validate the number of obtained interrupts in gpio-davinci
- add missing raw_spinlock_init() in gpio-graniterapids
- fix bad character device behavior: disallow GPIO line
reconfiguration without set direction both in v1 and v2 uAPI"
* tag 'gpio-fixes-for-v6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: cdev: Ignore reconfiguration without direction
gpiolib: cdev: Disallow reconfiguration without direction (uAPI v1)
gpio: graniterapids: Add missing raw_spinlock_init()
gpio: davinci: Validate the obtained number of IRQs
gpio: pca953x: fix pca953x_irq_bus_sync_unlock race
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"A pair of small arm64 fixes for -rc6.
One is a fix for the recently merged uffd-wp support (which was
triggering a spurious warning) and the other is a fix to the clearing
of the initial idmap pgd in some configurations
Summary:
- Fix spurious page-table warning when clearing PTE_UFFD_WP in a live
pte
- Fix clearing of the idmap pgd when using large addressing modes"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Clear the initial ID map correctly before remapping
arm64: mm: Permit PTE SW bits to change in live mappings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat fixes from Len Brown:
"Fix three recent minor turbostat regressions"
* tag 'v6.10-rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: Add local build_bug.h header for snapshot target
tools/power turbostat: Fix unc freq columns not showing with '-q' or '-l'
tools/power turbostat: option '-n' is ambiguous
|
|
Support tracking of up to 65535 packets per table entry instead of just
255 to better facilitate longer term tracking or higher throughput
scenarios.
Note how this aligns sizes of struct recent_entry's 'nstamps' and
'index' fields when 'nstamps' was larger before. This is unnecessary as
the value of 'nstamps' grows along with that of 'index' after being
initialized to 1 (see recent_entry_update()). Its value will thus never
exceed that of 'index' and therefore does not need to provide space for
larger values.
Requested-by: Fabio <[email protected]>
Link: https://bugzilla.netfilter.org/show_bug.cgi?id=1745
Signed-off-by: Phil Sutter <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
If userspace program exits while the queue its subscribed to has packets
those need to be discarded.
commit dc21c6cc3d69 ("netfilter: nfnetlink_queue: acquire rcu_read_lock()
in instance_destroy_rcu()") fixed a (harmless) rcu splat that could be
triggered in this case.
Add a test case to cover this.
Signed-off-by: Florian Westphal <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Work for __counted_by on generic pointers in structures (not just
flexible array members) has started landing in Clang 19 (current tip of
tree). During the development of this feature, a restriction was added
to __counted_by to prevent the flexible array member's element type from
including a flexible array member itself such as:
struct foo {
int count;
char buf[];
};
struct bar {
int count;
struct foo data[] __counted_by(count);
};
because the size of data cannot be calculated with the standard array
size formula:
sizeof(struct foo) * count
This restriction was downgraded to a warning but due to CONFIG_WERROR,
it can still break the build. The application of __counted_by on the
ports member of 'struct mxser_board' triggers this restriction,
resulting in:
drivers/tty/mxser.c:291:2: error: 'counted_by' should not be applied to an array with element of unknown size because 'struct mxser_port' is a struct type with a flexible array member. This will be an error in a future compiler version [-Werror,-Wbounds-safety-counted-by-elt-type-unknown-size]
291 | struct mxser_port ports[] __counted_by(nports);
| ^~~~~~~~~~~~~~~~~~~~~~~~~
1 error generated.
Remove this use of __counted_by to fix the warning/error. However,
rather than remove it altogether, leave it commented, as it may be
possible to support this in future compiler releases.
Cc: <[email protected]>
Closes: https://github.com/ClangBuiltLinux/linux/issues/2026
Fixes: f34907ecca71 ("mxser: Annotate struct mxser_board with __counted_by")
Signed-off-by: Nathan Chancellor <[email protected]>
Link: https://lore.kernel.org/r/20240529-drop-counted-by-ports-mxser-board-v1-1-0ab217f4da6d@kernel.org
Signed-off-by: Kees Cook <[email protected]>
|
|
An unintended consequence of commit 9c573cd31343 ("randomize_kstack:
Improve entropy diffusion") was that the per-architecture entropy size
filtering reduced how many bits were being added to the mix, rather than
how many bits were being used during the offsetting. All architectures
fell back to the existing default of 0x3FF (10 bits), which will consume
at most 1KiB of stack space. It seems that this is working just fine,
so let's avoid the confusion and update everything to use the default.
The prior intent of the per-architecture limits were:
arm64: capped at 0x1FF (9 bits), 5 bits effective
powerpc: uncapped (10 bits), 6 or 7 bits effective
riscv: uncapped (10 bits), 6 bits effective
x86: capped at 0xFF (8 bits), 5 (x86_64) or 6 (ia32) bits effective
s390: capped at 0xFF (8 bits), undocumented effective entropy
Current discussion has led to just dropping the original per-architecture
filters. The additional entropy appears to be safe for arm64, x86,
and s390. Quoting Arnd, "There is no point pretending that 15.75KB is
somehow safe to use while 15.00KB is not."
Co-developed-by: Yuntao Liu <[email protected]>
Signed-off-by: Yuntao Liu <[email protected]>
Fixes: 9c573cd31343 ("randomize_kstack: Improve entropy diffusion")
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Arnd Bergmann <[email protected]>
Acked-by: Mark Rutland <[email protected]>
Acked-by: Heiko Carstens <[email protected]> # s390
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Kees Cook <[email protected]>
|
|
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in lib/string_kunit.o
WARNING: modpost: missing MODULE_DESCRIPTION() in lib/string_helpers_kunit.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Kees Cook <[email protected]>
|
|
We got another report that CT1000BX500SSD1 does not work with LPM.
If you look in libata-core.c, we have six different Crucial devices that
are marked with ATA_HORKAGE_NOLPM. This model would have been the seventh.
(This quirk is used on Crucial models starting with both CT* and
Crucial_CT*)
It is obvious that this vendor does not have a great history of supporting
LPM properly, therefore, add the ATA_HORKAGE_NOLPM quirk for all Crucial
BX SSD1 models.
Fixes: 7627a0edef54 ("ata: ahci: Drop low power policy board type")
Cc: [email protected]
Reported-by: Alessandro Maggio <[email protected]>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218832
Reviewed-by: Damien Le Moal <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Niklas Cassel <[email protected]>
|
|
We cannot use CLONE_VFORK because we also need to wait for the timeout
signal.
Restore tests timeout by using the original fork() call in __run_test()
but also in __TEST_F_IMPL(). Also fix a race condition when waiting for
the test child process.
Because test metadata are shared between test processes, only the
parent process must set the test PID (child). Otherwise, t->pid may be
set to zero, leading to inconsistent error cases:
# RUN layout1.rule_on_mountpoint ...
# rule_on_mountpoint: Test ended in some other way [127]
# OK layout1.rule_on_mountpoint
ok 20 layout1.rule_on_mountpoint
As safeguards, initialize the "status" variable with a valid exit code,
and handle unknown test exits as errors.
The use of fork() introduces a new race condition in landlock/fs_test.c
which seems to be specific to hostfs bind mounts, but I haven't found
the root cause and it's difficult to trigger. I'll try to fix it with
another patch.
Cc: Christian Brauner <[email protected]>
Cc: Günther Noack <[email protected]>
Cc: Jakub Kicinski <[email protected]>
Cc: Kees Cook <[email protected]>
Cc: Shuah Khan <[email protected]>
Cc: Will Drewry <[email protected]>
Cc: [email protected]
Closes: https://lore.kernel.org/r/[email protected]
Fixes: a86f18903db9 ("selftests/harness: Fix interleaved scheduling leading to race conditions")
Fixes: 24cf65a62266 ("selftests/harness: Share _metadata between forked processes")
Link: https://lore.kernel.org/r/[email protected]
Tested-by: Mark Brown <[email protected]>
Signed-off-by: Mickaël Salaün <[email protected]>
|
|
Add support for the Xylanta SAINT3 product family.
Cc: Andy Jackson <[email protected]>
Cc: Ken Aitchison <[email protected]>
Tested-by: Andy Jackson <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
Update the maintainers entries to the new location of the
IOMMU tree.
Signed-off-by: Joerg Roedel <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan into main
|
|
Tariq Toukan says:
====================
mlx5 fixes 2024-06-27
This patchset provides fixes from the team to the mlx5 core and EN
drivers.
The first 3 patches by Daniel replace a buggy cap field with a newly
introduced one.
Patch 4 by Chris de-couples ingress ACL creation from a specific flow,
so it's invoked by other flows if needed.
Patch 5 by Jianbo fixes a possible missing cleanup of QoS objects.
Patches 6 and 7 by Leon fixes IPsec stats logic to better reflect the
traffic.
Series generated against:
commit 02ea312055da ("octeontx2-pf: Fix coverity and klockwork issues in octeon PF driver")
V2:
Fixed wrong cited SHA in patch 6.
====================
Signed-off-by: David S. Miller <[email protected]>
|