| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When sending TX packets, the meta descriptor can be all zeroes
as no meta information is required (as in XDP).
This patch removes the validity check, as when
`disable_meta_caching` is enabled, such TX packets will be
dropped otherwise.
Fixes: 0e3a3f6dacf0 ("net: ena: support new LLQ acceleration mode")
Signed-off-by: Shay Agroskin <[email protected]>
Signed-off-by: David Arinzon <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This patch fixes two issues:
Issue 1
-------
Description
```````````
Current code does not call dma_sync_single_for_cpu() to sync data from
the device side memory to the CPU side memory before the XDP code path
uses the CPU side data.
This causes the XDP code path to read the unset garbage data in the CPU
side memory, resulting in incorrect handling of the packet by XDP.
Solution
````````
1. Add a call to dma_sync_single_for_cpu() before the XDP code starts to
use the data in the CPU side memory.
2. The XDP code verdict can be XDP_PASS, in which case there is a
fallback to the non-XDP code, which also calls
dma_sync_single_for_cpu().
To avoid calling dma_sync_single_for_cpu() twice:
2.1. Put the dma_sync_single_for_cpu() in the code in such a place where
it happens before XDP and non-XDP code.
2.2. Remove the calls to dma_sync_single_for_cpu() in the non-XDP code
for the first buffer only (rx_copybreak and non-rx_copybreak
cases), since the new call that was added covers these cases.
The call to dma_sync_single_for_cpu() for the second buffer and on
stays because only the first buffer is handled by the newly added
dma_sync_single_for_cpu(). And there is no need for special
handling of the second buffer and on for the XDP path since
currently the driver supports only single buffer packets.
Issue 2
-------
Description
```````````
In case the XDP code forwarded the packet (ENA_XDP_FORWARDED),
ena_unmap_rx_buff_attrs() is called with attrs set to 0.
This means that before unmapping the buffer, the internal function
dma_unmap_page_attrs() will also call dma_sync_single_for_cpu() on
the whole buffer (not only on the data part of it).
This sync is both wasteful (since a sync was already explicitly
called before) and also causes a bug, which will be explained
using the below diagram.
The following diagram shows the flow of events causing the bug.
The order of events is (1)-(4) as shown in the diagram.
CPU side memory area
(3)convert_to_xdp_frame() initializes the
headroom with xdpf metadata
||
\/
___________________________________
| |
0 | V 4K
---------------------------------------------------------------------
| xdpf->data | other xdpf | < data > | tailroom ||...|
| | fields | | GARBAGE || |
---------------------------------------------------------------------
/\ /\
|| ||
(4)ena_unmap_rx_buff_attrs() calls (2)dma_sync_single_for_cpu()
dma_sync_single_for_cpu() on the copies data from device
whole buffer page, overwriting side to CPU side memory
the xdpf->data with GARBAGE. ||
0 4K
---------------------------------------------------------------------
| headroom | < data > | tailroom ||...|
| GARBAGE | | GARBAGE || |
---------------------------------------------------------------------
Device side memory area /\
||
(1) device writes RX packet data
After the call to ena_unmap_rx_buff_attrs() in (4), the xdpf->data
becomes corrupted, and so when it is later accessed in
ena_clean_xdp_irq()->xdp_return_frame(), it causes a page fault,
crashing the kernel.
Solution
````````
Explicitly tell ena_unmap_rx_buff_attrs() not to call
dma_sync_single_for_cpu() by passing it the ENA_DMA_ATTR_SKIP_CPU_SYNC
flag.
Fixes: f7d625adeb7b ("net: ena: Add dynamic recycling mechanism for rx buffers")
Signed-off-by: Arthur Kiyanovski <[email protected]>
Signed-off-by: David Arinzon <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Current xdp code drops packets larger than ENA_XDP_MAX_MTU.
This is an incorrect condition since the problem is not the
size of the packet, rather the number of buffers it contains.
This commit:
1. Identifies and drops XDP multi-buffer packets at the
beginning of the function.
2. Increases the xdp drop statistic when this drop occurs.
3. Adds a one-time print that such drops are happening to
give better indication to the user.
Fixes: 838c93dc5449 ("net: ena: implement XDP drop support")
Signed-off-by: Arthur Kiyanovski <[email protected]>
Signed-off-by: David Arinzon <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The ena_setup_and_create_all_xdp_queues() function freed all the
resources upon failure, after creating only xdp_num_queues queues,
instead of freeing just the created ones.
In this patch, the only resources that are freed, are the ones
allocated right before the failure occurs.
Fixes: 548c4940b9f1 ("net: ena: Implement XDP_TX action")
Signed-off-by: Shahar Itzko <[email protected]>
Signed-off-by: David Arinzon <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The snapshot buffer is to mimic the main buffer so that when a snapshot is
needed, the snapshot and main buffer are swapped. When the snapshot buffer
is allocated, it is set to the minimal size that the ring buffer may be at
and still functional. When it is allocated it becomes the same size as the
main ring buffer, and when the main ring buffer changes in size, it should
do.
Currently, the resize only updates the snapshot buffer if it's used by the
current tracer (ie. the preemptirqsoff tracer). But it needs to be updated
anytime it is allocated.
When changing the size of the main buffer, instead of looking to see if
the current tracer is utilizing the snapshot buffer, just check if it is
allocated to know if it should be updated or not.
Also fix typo in comment just above the code change.
Link: https://lore.kernel.org/linux-trace-kernel/[email protected]
Cc: [email protected]
Cc: Mark Rutland <[email protected]>
Cc: Mathieu Desnoyers <[email protected]>
Fixes: ad909e21bbe69 ("tracing: Add internal tracing_snapshot() functions")
Reviewed-by: Masami Hiramatsu (Google) <[email protected]>
Signed-off-by: Steven Rostedt (Google) <[email protected]>
|
|
Reading the ring buffer does a swap of a sub-buffer within the ring buffer
with a empty sub-buffer. This allows the reader to have full access to the
content of the sub-buffer that was swapped out without having to worry
about contention with the writer.
The readers call ring_buffer_alloc_read_page() to allocate a page that
will be used to swap with the ring buffer. When the code is finished with
the reader page, it calls ring_buffer_free_read_page(). Instead of freeing
the page, it stores it as a spare. Then next call to
ring_buffer_alloc_read_page() will return this spare instead of calling
into the memory management system to allocate a new page.
Unfortunately, on freeing of the ring buffer, this spare page is not
freed, and causes a memory leak.
Link: https://lore.kernel.org/linux-trace-kernel/[email protected]
Cc: [email protected]
Cc: Mark Rutland <[email protected]>
Cc: Mathieu Desnoyers <[email protected]>
Fixes: 73a757e63114d ("ring-buffer: Return reader page back into existing ring buffer")
Acked-by: Masami Hiramatsu (Google) <[email protected]>
Signed-off-by: Steven Rostedt (Google) <[email protected]>
|
|
Eventfs uses simple_lookup(), however, it will fail if the name of the
entry is beyond NAME_MAX length. When this error is encountered, eventfs
still tries to create dentries instead of skipping the dentry creation.
When the dentry is attempted to be created in this state d_wait_lookup()
will loop forever, waiting for the lookup to be removed.
Fix eventfs to return the error in simple_lookup() back to the caller
instead of continuing to try to create the dentry.
Link: https://lore.kernel.org/linux-trace-kernel/[email protected]
Fixes: 63940449555e ("eventfs: Implement eventfs lookup, read, open functions")
Link: https://lore.kernel.org/linux-trace-kernel/[email protected]/
Signed-off-by: Beau Belgrave <[email protected]>
Signed-off-by: Steven Rostedt (Google) <[email protected]>
|
|
If a large event was added to the ring buffer that is larger than what the
trace_seq can handle, it just drops the output:
~# cat /sys/kernel/tracing/trace
# tracer: nop
#
# entries-in-buffer/entries-written: 2/2 #P:8
#
# _-----=> irqs-off/BH-disabled
# / _----=> need-resched
# | / _---=> hardirq/softirq
# || / _--=> preempt-depth
# ||| / _-=> migrate-disable
# |||| / delay
# TASK-PID CPU# ||||| TIMESTAMP FUNCTION
# | | | ||||| | |
<...>-859 [001] ..... 141.118951: tracing_mark_write <...>-859 [001] ..... 141.148201: tracing_mark_write: 78901234
Instead, catch this case and add some context:
~# cat /sys/kernel/tracing/trace
# tracer: nop
#
# entries-in-buffer/entries-written: 2/2 #P:8
#
# _-----=> irqs-off/BH-disabled
# / _----=> need-resched
# | / _---=> hardirq/softirq
# || / _--=> preempt-depth
# ||| / _-=> migrate-disable
# |||| / delay
# TASK-PID CPU# ||||| TIMESTAMP FUNCTION
# | | | ||||| | |
<...>-852 [001] ..... 121.550551: tracing_mark_write[LINE TOO BIG]
<...>-852 [001] ..... 121.550581: tracing_mark_write: 78901234
This now emulates the same output as trace_pipe.
Link: https://lore.kernel.org/linux-trace-kernel/[email protected]
Cc: Mark Rutland <[email protected]>
Cc: Mathieu Desnoyers <[email protected]>
Reviewed-by: Masami Hiramatsu (Google) <[email protected]>
Signed-off-by: Steven Rostedt (Google) <[email protected]>
|
|
The maximum ring buffer data size is the maximum size of data that can be
recorded on the ring buffer. Events must be smaller than the sub buffer
data size minus any meta data. This size is checked before trying to
allocate from the ring buffer because the allocation assumes that the size
will fit on the sub buffer.
The maximum size was calculated as the size of a sub buffer page (which is
currently PAGE_SIZE minus the sub buffer header) minus the size of the
meta data of an individual event. But it missed the possible adding of a
time stamp for events that are added long enough apart that the event meta
data can't hold the time delta.
When an event is added that is greater than the current BUF_MAX_DATA_SIZE
minus the size of a time stamp, but still less than or equal to
BUF_MAX_DATA_SIZE, the ring buffer would go into an infinite loop, looking
for a page that can hold the event. Luckily, there's a check for this loop
and after 1000 iterations and a warning is emitted and the ring buffer is
disabled. But this should never happen.
This can happen when a large event is added first, or after a long period
where an absolute timestamp is prefixed to the event, increasing its size
by 8 bytes. This passes the check and then goes into the algorithm that
causes the infinite loop.
For events that are the first event on the sub-buffer, it does not need to
add a timestamp, because the sub-buffer itself contains an absolute
timestamp, and adding one is redundant.
The fix is to check if the event is to be the first event on the
sub-buffer, and if it is, then do not add a timestamp.
This also fixes 32 bit adding a timestamp when a read of before_stamp or
write_stamp is interrupted. There's still no need to add that timestamp if
the event is going to be the first event on the sub buffer.
Also, if the buffer has "time_stamp_abs" set, then also check if the
length plus the timestamp is greater than the BUF_MAX_DATA_SIZE.
Link: https://lore.kernel.org/all/[email protected]/
Link: https://lore.kernel.org/linux-trace-kernel/[email protected]
Link: https://lore.kernel.org/linux-trace-kernel/[email protected]
Cc: [email protected]
Cc: Mark Rutland <[email protected]>
Cc: Mathieu Desnoyers <[email protected]>
Fixes: a4543a2fa9ef3 ("ring-buffer: Get timestamp after event is allocated")
Fixes: 58fbc3c63275c ("ring-buffer: Consolidate add_timestamp to remove some branches")
Reported-by: Kent Overstreet <[email protected]> # (on IRC)
Acked-by: Masami Hiramatsu (Google) <[email protected]>
Signed-off-by: Steven Rostedt (Google) <[email protected]>
|
|
syzkaller report:
kernel BUG at net/core/skbuff.c:3452!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.7.0-rc4-00009-gbee0e7762ad2-dirty #135
RIP: 0010:skb_copy_and_csum_bits (net/core/skbuff.c:3452)
Call Trace:
icmp_glue_bits (net/ipv4/icmp.c:357)
__ip_append_data.isra.0 (net/ipv4/ip_output.c:1165)
ip_append_data (net/ipv4/ip_output.c:1362 net/ipv4/ip_output.c:1341)
icmp_push_reply (net/ipv4/icmp.c:370)
__icmp_send (./include/net/route.h:252 net/ipv4/icmp.c:772)
ip_fragment.constprop.0 (./include/linux/skbuff.h:1234 net/ipv4/ip_output.c:592 net/ipv4/ip_output.c:577)
__ip_finish_output (net/ipv4/ip_output.c:311 net/ipv4/ip_output.c:295)
ip_output (net/ipv4/ip_output.c:427)
__ip_queue_xmit (net/ipv4/ip_output.c:535)
__tcp_transmit_skb (net/ipv4/tcp_output.c:1462)
__tcp_retransmit_skb (net/ipv4/tcp_output.c:3387)
tcp_retransmit_skb (net/ipv4/tcp_output.c:3404)
tcp_retransmit_timer (net/ipv4/tcp_timer.c:604)
tcp_write_timer (./include/linux/spinlock.h:391 net/ipv4/tcp_timer.c:716)
The panic issue was trigered by tcp simultaneous initiation.
The initiation process is as follows:
TCP A TCP B
1. CLOSED CLOSED
2. SYN-SENT --> <SEQ=100><CTL=SYN> ...
3. SYN-RECEIVED <-- <SEQ=300><CTL=SYN> <-- SYN-SENT
4. ... <SEQ=100><CTL=SYN> --> SYN-RECEIVED
5. SYN-RECEIVED --> <SEQ=100><ACK=301><CTL=SYN,ACK> ...
// TCP B: not send challenge ack for ack limit or packet loss
// TCP A: close
tcp_close
tcp_send_fin
if (!tskb && tcp_under_memory_pressure(sk))
tskb = skb_rb_last(&sk->tcp_rtx_queue); //pick SYN_ACK packet
TCP_SKB_CB(tskb)->tcp_flags |= TCPHDR_FIN; // set FIN flag
6. FIN_WAIT_1 --> <SEQ=100><ACK=301><END_SEQ=102><CTL=SYN,FIN,ACK> ...
// TCP B: send challenge ack to SYN_FIN_ACK
7. ... <SEQ=301><ACK=101><CTL=ACK> <-- SYN-RECEIVED //challenge ack
// TCP A: <SND.UNA=101>
8. FIN_WAIT_1 --> <SEQ=101><ACK=301><END_SEQ=102><CTL=SYN,FIN,ACK> ... // retransmit panic
__tcp_retransmit_skb //skb->len=0
tcp_trim_head
len = tp->snd_una - TCP_SKB_CB(skb)->seq // len=101-100
__pskb_trim_head
skb->data_len -= len // skb->len=-1, wrap around
... ...
ip_fragment
icmp_glue_bits //BUG_ON
If we use tcp_trim_head() to remove acked SYN from packet that contains data
or other flags, skb->len will be incorrectly decremented. We can remove SYN
flag that has been acked from rtx_queue earlier than tcp_trim_head(), which
can fix the problem mentioned above.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Co-developed-by: Eric Dumazet <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: Dong Chenchen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
qed_ilt_shadow_alloc() will call qed_ilt_shadow_free() to
free p_hwfn->p_cxt_mngr->ilt_shadow on error. However,
qed_cxt_tables_alloc() accesses the freed pointer on failure
of qed_ilt_shadow_alloc() through calling qed_cxt_mngr_free(),
which may lead to use-after-free. Fix this issue by setting
p_mngr->ilt_shadow to NULL in qed_ilt_shadow_free().
Fixes: fe56b9e6a8d9 ("qed: Add module with basic common support")
Reviewed-by: Przemek Kitszel <[email protected]>
Signed-off-by: Dinghao Liu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
If some of p9pdu_readf() calls inside case 'T' in p9pdu_vreadf() fails,
the error path is not handled properly. *wnames or members of *wnames
array may be left uninitialized and invalidly freed.
Initialize *wnames to NULL in beginning of case 'T'. Initialize the first
*wnames array element to NULL and nullify the failing *wnames element so
that the error path freeing loop stops on the first NULL element and
doesn't proceed further.
Found by Linux Verification Center (linuxtesting.org).
Fixes: ace51c4dd2f9 ("9p: add new protocol support code")
Signed-off-by: Fedor Pchelkin <[email protected]>
Message-ID: <[email protected]>
Cc: [email protected]
Reviewed-by: Simon Horman <[email protected]>
Reviewed-by: Christian Schoenebeck <[email protected]>
Signed-off-by: Dominique Martinet <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Fix various bugs / regressions for ext4, including a soft lockup, a
WARN_ON, and a BUG"
* tag 'ext4_for_linus-6.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
jbd2: fix soft lockup in journal_finish_inode_data_buffers()
ext4: fix warning in ext4_dio_write_end_io()
jbd2: increase the journal IO's priority
jbd2: correct the printing of write_flags in jbd2_write_superblock()
ext4: prevent the normalized size from exceeding EXT_MAX_BLOCKS
|
|
Make the flow for pci shutdown be the same to the pci remove.
iavf_shutdown was implementing an incomplete version
of iavf_remove. It misses several calls to the kernel like
iavf_free_misc_irq, iavf_reset_interrupt_capability, iounmap
that might break the system on reboot or hibernation.
Implement the call of iavf_remove directly in iavf_shutdown to
close this gap.
Fixes below error messages (dmesg) during shutdown stress tests -
[685814.900917] ice 0000:88:00.0: MAC 02:d0:5f:82:43:5d does not exist for
VF 0
[685814.900928] ice 0000:88:00.0: MAC 33:33:00:00:00:01 does not exist for
VF 0
Reproduction:
1. Create one VF interface:
echo 1 > /sys/class/net/<interface_name>/device/sriov_numvfs
2. Run live dmesg on the host:
dmesg -wH
3. On SUT, script below steps into vf_namespace_assignment.sh
<#!/bin/sh> // Remove <>. Git removes # line
if=<VF name> (edit this per VF name)
loop=0
while true; do
echo test round $loop
let loop++
ip netns add ns$loop
ip link set dev $if up
ip link set dev $if netns ns$loop
ip netns exec ns$loop ip link set dev $if up
ip netns exec ns$loop ip link set dev $if netns 1
ip netns delete ns$loop
done
4. Run the script for at least 1000 iterations on SUT:
./vf_namespace_assignment.sh
Expected result:
No errors in dmesg.
Fixes: 129cf89e5856 ("iavf: rename functions and structs to new name")
Signed-off-by: Slawomir Laba <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Reviewed-by: Ahmed Zaki <[email protected]>
Reviewed-by: Jesse Brandeburg <[email protected]>
Co-developed-by: Ranganatha Rao <[email protected]>
Signed-off-by: Ranganatha Rao <[email protected]>
Tested-by: Rafal Romanowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
ntuple-filter feature on/off:
Default is on. If turned off, the filters will be removed from both
PF and iavf list. The removal is irrespective of current filter state.
Steps to reproduce:
-------------------
1. Ensure ntuple is on.
ethtool -K enp8s0 ntuple-filters on
2. Create a filter to receive the traffic into non-default rx-queue like 15
and ensure traffic is flowing into queue into 15.
Now, turn off ntuple. Traffic should not flow to configured queue 15.
It should flow to default RX queue.
Fixes: 0dbfbabb840d ("iavf: Add framework to enable ethtool ntuple filters")
Signed-off-by: Piotr Gardocki <[email protected]>
Reviewed-by: Larysa Zaremba <[email protected]>
Signed-off-by: Ranganatha Rao <[email protected]>
Tested-by: Rafal Romanowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
New states introduced:
IAVF_FDIR_FLTR_DIS_REQUEST
IAVF_FDIR_FLTR_DIS_PENDING
IAVF_FDIR_FLTR_INACTIVE
Current FDIR state machines (SM) are not adequate to handle a few
scenarios in the link DOWN/UP event, reset event and ntuple-feature.
For example, when VF link goes DOWN and comes back UP administratively,
the expectation is that previously installed filters should also be
restored. But with current SM, filters are not restored.
So with new SM, during link DOWN filters are marked as INACTIVE in
the iavf list but removed from PF. After link UP, SM will transition
from INACTIVE to ADD_REQUEST to restore the filter.
Similarly, with VF reset, filters will be removed from the PF, but
marked as INACTIVE in the iavf list. Filters will be restored after
reset completion.
Steps to reproduce:
-------------------
1. Create a VF. Here VF is enp8s0.
2. Assign IP addresses to VF and link partner and ping continuously
from remote. Here remote IP is 1.1.1.1.
3. Check default RX Queue of traffic.
ethtool -S enp8s0 | grep -E "rx-[[:digit:]]+\.packets"
4. Add filter - change default RX Queue (to 15 here)
ethtool -U ens8s0 flow-type ip4 src-ip 1.1.1.1 action 15 loc 5
5. Ensure filter gets added and traffic is received on RX queue 15 now.
Link event testing:
-------------------
6. Bring VF link down and up. If traffic flows to configured queue 15,
test is success, otherwise it is a failure.
Reset event testing:
--------------------
7. Reset the VF. If traffic flows to configured queue 15, test is success,
otherwise it is a failure.
Fixes: 0dbfbabb840d ("iavf: Add framework to enable ethtool ntuple filters")
Signed-off-by: Piotr Gardocki <[email protected]>
Reviewed-by: Larysa Zaremba <[email protected]>
Signed-off-by: Ranganatha Rao <[email protected]>
Tested-by: Rafal Romanowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
- Fix a couple of potential crashes, one introduced in 6.6 and one
in 5.10
- Fix misbehavior of virtiofs submounts on memory pressure
- Clarify naming in the uAPI for a recent feature
* tag 'fuse-fixes-6.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: disable FOPEN_PARALLEL_DIRECT_WRITES with FUSE_DIRECT_IO_ALLOW_MMAP
fuse: dax: set fc->dax to NULL in fuse_dax_conn_free()
fuse: share lookup state between submount and its parent
docs/fuse-io: Document the usage of DIRECT_IO_ALLOW_MMAP
fuse: Rename DIRECT_IO_RELAX to DIRECT_IO_ALLOW_MMAP
|
|
Pull smb server fixes from Steve French:
- Memory leak fix (in lock error path)
- Two fixes for create with allocation size
- FIx for potential UAF in lease break error path
- Five directory lease (caching) fixes found during additional recent
testing
* tag '6.7-rc5-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: fix wrong name of SMB2_CREATE_ALLOCATION_SIZE
ksmbd: fix wrong allocation size update in smb2_open()
ksmbd: avoid duplicate opinfo_put() call on error of smb21_lease_break_ack()
ksmbd: lazy v2 lease break on smb2_write()
ksmbd: send v2 lease break notification for directory
ksmbd: downgrade RWH lease caching state to RH for directory
ksmbd: set v2 lease capability
ksmbd: set epoch in create context v2 lease
ksmbd: fix memory leak in smb2_lock()
|
|
When screen brightness is rapidly changed and PSR-SU is enabled the
display hangs on panels with this TCON even on the latest DCN 3.1.4
microcode (0x8002a81 at this time).
This was disabled previously as commit 072030b17830 ("drm/amd: Disable
PSR-SU on Parade 0803 TCON") but reverted as commit 1e66a17ce546 ("Revert
"drm/amd: Disable PSR-SU on Parade 0803 TCON"") in favor of testing for
a new enough microcode (commit cd2e31a9ab93 ("drm/amd/display: Set minimum
requirement for using PSR-SU on Phoenix")).
As hangs are still happening specifically with this TCON, disable PSR-SU
again for it until it can be root caused.
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: Marc Rossi <[email protected]>
Cc: Hamza Mahfooz <[email protected]>
Signed-off-by: Mario Limonciello <[email protected]>
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2046131
Acked-by: Alex Deucher <[email protected]>
Reviewed-by: Harry Wentland <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
dtbclk is unavaliable from pmfw. Try to grab the value from bounding box
Reviewed-by: Charlene Liu <[email protected]>
Acked-by: Aurabindo Pillai <[email protected]>
Signed-off-by: Fangzhi Zuo <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why & How]
HostVMMinPageSize is expected to be in KB according to spec,
the checks later down the line reflect this as well.
Reviewed-by: Nicholas Kazlauskas <[email protected]>
Acked-by: Aurabindo Pillai <[email protected]>
Signed-off-by: Taimur Hassan <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Doorbell is configured during start of each playback.
v1 - add comment for the doorbell programming change
Signed-off-by: Saleemkhan Jamadar <[email protected]>
Acked-by: Leo Liu <[email protected]>
Reviewed-by: Veerabadhran Gopalakrishnan <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Building the KVM selftests from the main selftests Makefile (as opposed
to the kvm subdirectory) doesn't work as OUTPUT is set, forcing the
generated header to spill into the selftests directory. Additionally,
relative paths do not work when building outside of the srctree, as the
canonical selftests path is replaced with 'kselftest' in the output.
Work around both of these issues by explicitly overriding OUTPUT on the
submake cmdline. Move the whole fragment below the point lib.mk gets
included such that $(abs_objdir) is available.
Reviewed-by: Cornelia Huck <[email protected]>
Tested-by: Mark Brown <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Oliver Upton <[email protected]>
|
|
It is currently possible for a userspace application to enter an
infinite page fault loop when using HugeTLB pages implemented with
contiguous PTEs when HAFDBS is not available. This happens because:
1. The kernel may sometimes write PTEs that are sw-dirty but hw-clean
(PTE_DIRTY | PTE_RDONLY | PTE_WRITE).
2. If, during a write, the CPU uses a sw-dirty, hw-clean PTE in handling
the memory access on a system without HAFDBS, we will get a page
fault.
3. HugeTLB will check if it needs to update the dirty bits on the PTE.
For contiguous PTEs, it will check to see if the pgprot bits need
updating. In this case, HugeTLB wants to write a sequence of
sw-dirty, hw-dirty PTEs, but it finds that all the PTEs it is about
to overwrite are all pte_dirty() (pte_sw_dirty() => pte_dirty()),
so it thinks no update is necessary.
We can get the kernel to write a sw-dirty, hw-clean PTE with the
following steps (showing the relevant VMA flags and pgprot bits):
i. Create a valid, writable contiguous PTE.
VMA vmflags: VM_SHARED | VM_READ | VM_WRITE
VMA pgprot bits: PTE_RDONLY | PTE_WRITE
PTE pgprot bits: PTE_DIRTY | PTE_WRITE
ii. mprotect the VMA to PROT_NONE.
VMA vmflags: VM_SHARED
VMA pgprot bits: PTE_RDONLY
PTE pgprot bits: PTE_DIRTY | PTE_RDONLY
iii. mprotect the VMA back to PROT_READ | PROT_WRITE.
VMA vmflags: VM_SHARED | VM_READ | VM_WRITE
VMA pgprot bits: PTE_RDONLY | PTE_WRITE
PTE pgprot bits: PTE_DIRTY | PTE_WRITE | PTE_RDONLY
Make it impossible to create a writeable sw-dirty, hw-clean PTE with
pte_modify(). Such a PTE should be impossible to create, and there may
be places that assume that pte_dirty() implies pte_hw_dirty().
Signed-off-by: James Houghton <[email protected]>
Fixes: 031e6e6b4e12 ("arm64: hugetlb: Avoid unnecessary clearing in huge_ptep_set_access_flags")
Cc: <[email protected]>
Acked-by: Will Deacon <[email protected]>
Reviewed-by: Ryan Roberts <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Catalin Marinas <[email protected]>
|
|
There's issue when do io test:
WARN: soft lockup - CPU#45 stuck for 11s! [jbd2/dm-2-8:4170]
CPU: 45 PID: 4170 Comm: jbd2/dm-2-8 Kdump: loaded Tainted: G OE
Call trace:
dump_backtrace+0x0/0x1a0
show_stack+0x24/0x30
dump_stack+0xb0/0x100
watchdog_timer_fn+0x254/0x3f8
__hrtimer_run_queues+0x11c/0x380
hrtimer_interrupt+0xfc/0x2f8
arch_timer_handler_phys+0x38/0x58
handle_percpu_devid_irq+0x90/0x248
generic_handle_irq+0x3c/0x58
__handle_domain_irq+0x68/0xc0
gic_handle_irq+0x90/0x320
el1_irq+0xcc/0x180
queued_spin_lock_slowpath+0x1d8/0x320
jbd2_journal_commit_transaction+0x10f4/0x1c78 [jbd2]
kjournald2+0xec/0x2f0 [jbd2]
kthread+0x134/0x138
ret_from_fork+0x10/0x18
Analyzed informations from vmcore as follows:
(1) There are about 5k+ jbd2_inode in 'commit_transaction->t_inode_list';
(2) Now is processing the 855th jbd2_inode;
(3) JBD2 task has TIF_NEED_RESCHED flag;
(4) There's no pags in address_space around the 855th jbd2_inode;
(5) There are some process is doing drop caches;
(6) Mounted with 'nodioread_nolock' option;
(7) 128 CPUs;
According to informations from vmcore we know 'journal->j_list_lock' spin lock
competition is fierce. So journal_finish_inode_data_buffers() maybe process
slowly. Theoretically, there is scheduling point in the filemap_fdatawait_range_keep_errors().
However, if inode's address_space has no pages which taged with PAGECACHE_TAG_WRITEBACK,
will not call cond_resched(). So may lead to soft lockup.
journal_finish_inode_data_buffers
filemap_fdatawait_range_keep_errors
__filemap_fdatawait_range
while (index <= end)
nr_pages = pagevec_lookup_range_tag(&pvec, mapping, &index, end, PAGECACHE_TAG_WRITEBACK);
if (!nr_pages)
break; --> If 'nr_pages' is equal zero will break, then will not call cond_resched()
for (i = 0; i < nr_pages; i++)
wait_on_page_writeback(page);
cond_resched();
To solve above issue, add scheduling point in the journal_finish_inode_data_buffers();
Signed-off-by: Ye Bin <[email protected]>
Reviewed-by: Jan Kara <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Theodore Ts'o <[email protected]>
|
|
If WED rx is enabled, rx buffers are added to a buffer pool that can be
filled from multiple page pools. Because buffers freed from rx poll are
not guaranteed to belong to the processed queue's page pool, lockless
caching must not be used in this case.
Cc: [email protected]
Fixes: 2f5c3c77fc9b ("wifi: mt76: switch to page_pool allocator")
Signed-off-by: Felix Fietkau <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
JingZao(京造) WKB603 keyboard is a rebranded product of Jamesdonkey RS2
keyboard, identified as "hfd.cn WKB603" in wired mode, "WKB603" in bluetooth
mode. Adding them to the list of non-apple keyboards fixes function key.
Signed-off-by: Yan Jun <[email protected]>
Signed-off-by: Jiri Kosina <[email protected]>
|
|
Commit 46a0a2c96f0f ("HID: lenovo: Detect quirk-free fw on cptkbd and
stop applying workaround") introduced a regression for ThinkPad
TrackPoint Keyboard II which has similar quirks to cptkbd (so it uses
the same workarounds) but slightly different so that there are
false-positives during detecting well-behaving firmware. This commit
restricts detecting well-behaving firmware to the only model which
known to have one and have stable enough quirks to not cause
false-positives.
Fixes: 46a0a2c96f0f ("HID: lenovo: Detect quirk-free fw on cptkbd and stop applying workaround")
Link: https://lore.kernel.org/linux-input/ZXRiiPsBKNasioqH@jekhomev/
Link: https://bbs.archlinux.org/viewtopic.php?pid=2135468#p2135468
Signed-off-by: Mikhail Khvainitski <[email protected]>
Tested-by: Yauhen Kharuzhy <[email protected]>
Signed-off-by: Jiri Kosina <[email protected]>
|
|
Because rose_ioctl() accesses sk->sk_receive_queue
without holding a sk->sk_receive_queue.lock, it can
cause a race with rose_accept().
A use-after-free for skb occurs with the following flow.
```
rose_ioctl() -> skb_peek()
rose_accept() -> skb_dequeue() -> kfree_skb()
```
Add sk->sk_receive_queue.lock to rose_ioctl() to fix this issue.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Hyunwoo Kim <[email protected]>
Link: https://lore.kernel.org/r/20231209100538.GA407321@v4bel-B760M-AORUS-ELITE-AX
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Because do_vcc_ioctl() accesses sk->sk_receive_queue
without holding a sk->sk_receive_queue.lock, it can
cause a race with vcc_recvmsg().
A use-after-free for skb occurs with the following flow.
```
do_vcc_ioctl() -> skb_peek()
vcc_recvmsg() -> skb_recv_datagram() -> skb_free_datagram()
```
Add sk->sk_receive_queue.lock to do_vcc_ioctl() to fix this issue.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Hyunwoo Kim <[email protected]>
Link: https://lore.kernel.org/r/20231209094210.GA403126@v4bel-B760M-AORUS-ELITE-AX
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Calling arm_cmn_event_clear() before all DTC indices are allocated is
wrong, and can lead to arm_cmn_event_add() erroneously clearing live
counters from full DTCs where allocation fails. Since the DTC counters
are only updated by arm_cmn_init_counter() after all DTC and DTM
allocations succeed, nothing actually needs cleaning up in this case
anyway, and it should just return directly as it did before.
Fixes: 7633ec2c262f ("perf/arm-cmn: Rework DTC counters (again)")
Signed-off-by: Robin Murphy <[email protected]>
Reviewed-by: Ilkka Koskinen <[email protected]>
Acked-by: Will Deacon <[email protected]>
Link: https://lore.kernel.org/r/ed589c0d8e4130dc68b8ad1625226d28bdc185d4.1702322847.git.robin.murphy@arm.com
Signed-off-by: Catalin Marinas <[email protected]>
|
|
It possible that while the rx rb is being handled, the transport has
been stopped and re-started. In this case the tx queue pointer is not
yet initialized, which will lead to a NULL pointer dereference.
Fix it.
Signed-off-by: Avraham Stern <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231207044813.cd0898cafd89.I0b84daae753ba9612092bf383f5c6f761446e964@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
During refactoring the "else" here got lost, add it back.
Fixes: c99a89edb106 ("mac80211: factor out plink event gathering")
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231211085121.795480fa0e0b.I017d501196a5bbdcd9afd33338d342d6fe1edd79@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
ieee802_11_parse_elems() can return NULL, so we must
check for the return value.
Fixes: 5d24828d05f3 ("mac80211: always allocate struct ieee802_11_elems")
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231211085121.93dea364f3d3.Ie87781c6c48979fb25a744b90af4a33dc2d83a28@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
We need to check that cfg80211_defragment_element()
didn't return an error, since it can fail due to bad
input, and we didn't catch that before.
Fixes: 8eb8dd2ffbbb ("wifi: mac80211: Support link removal using Reconfiguration ML element")
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231211085121.8595a6b67fc0.I1225edd8f98355e007f96502e358e476c7971d8c@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
If we're doing reconfig, then we cannot add the debugfs
files that are already there from before the reconfig.
Skip that in drv_change_sta_links() during reconfig.
Fixes: d2caad527c19 ("wifi: mac80211: add API to show the link STAs in debugfs")
Signed-off-by: Johannes Berg <[email protected]>
Reviewed-by: Gregory Greenman <[email protected]>
Reviewed-by: Benjamin Berg <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231211085121.88a950f43e16.Id71181780994649219685887c0fcad33d387cc78@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
Fix the undefined usage of the GPIO consumer API after retrieving the
GPIO description with GPIO_ASIS. The API documentation mentions that
GPIO_ASIS won't set a GPIO direction and requires the user to set a
direction before using the GPIO.
This can be confirmed on i.MX6 hardware, where rfkill-gpio is no longer
able to enabled/disable a device, presumably because the GPIO controller
was never configured for the output direction.
Fixes: b2f750c3a80b ("net: rfkill: gpio: prevent value glitch during probe")
Cc: [email protected]
Signed-off-by: Rouven Czerwinski <[email protected]>
Link: https://msgid.link/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
|
|
[Syz report]
WARNING: CPU: 1 PID: 5067 at net/mac80211/rate.c:48 rate_control_rate_init+0x540/0x690 net/mac80211/rate.c:48
Modules linked in:
CPU: 1 PID: 5067 Comm: syz-executor413 Not tainted 6.7.0-rc3-syzkaller-00014-gdf60cee26a2e #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/10/2023
RIP: 0010:rate_control_rate_init+0x540/0x690 net/mac80211/rate.c:48
Code: 48 c7 c2 00 46 0c 8c be 08 03 00 00 48 c7 c7 c0 45 0c 8c c6 05 70 79 0b 05 01 e8 1b a0 6f f7 e9 e0 fd ff ff e8 61 b3 8f f7 90 <0f> 0b 90 e9 36 ff ff ff e8 53 b3 8f f7 e8 5e 0b 78 f7 31 ff 89 c3
RSP: 0018:ffffc90003c57248 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff888016bc4000 RCX: ffffffff89f7d519
RDX: ffff888076d43b80 RSI: ffffffff89f7d6df RDI: 0000000000000005
RBP: ffff88801daaae20 R08: 0000000000000005 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000002 R12: 0000000000000001
R13: 0000000000000000 R14: ffff888020030e20 R15: ffff888078f08000
FS: 0000555556b94380(0000) GS:ffff8880b9900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000005fdeb8 CR3: 0000000076d22000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
sta_apply_auth_flags.constprop.0+0x4b7/0x510 net/mac80211/cfg.c:1674
sta_apply_parameters+0xaf1/0x16c0 net/mac80211/cfg.c:2002
ieee80211_add_station+0x3fa/0x6c0 net/mac80211/cfg.c:2068
rdev_add_station net/wireless/rdev-ops.h:201 [inline]
nl80211_new_station+0x13ba/0x1a70 net/wireless/nl80211.c:7603
genl_family_rcv_msg_doit+0x1fc/0x2e0 net/netlink/genetlink.c:972
genl_family_rcv_msg net/netlink/genetlink.c:1052 [inline]
genl_rcv_msg+0x561/0x800 net/netlink/genetlink.c:1067
netlink_rcv_skb+0x16b/0x440 net/netlink/af_netlink.c:2545
genl_rcv+0x28/0x40 net/netlink/genetlink.c:1076
netlink_unicast_kernel net/netlink/af_netlink.c:1342 [inline]
netlink_unicast+0x53b/0x810 net/netlink/af_netlink.c:1368
netlink_sendmsg+0x93c/0xe40 net/netlink/af_netlink.c:1910
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0xd5/0x180 net/socket.c:745
____sys_sendmsg+0x6ac/0x940 net/socket.c:2584
___sys_sendmsg+0x135/0x1d0 net/socket.c:2638
__sys_sendmsg+0x117/0x1e0 net/socket.c:2667
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x40/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b
[Analysis]
It is inappropriate to make a link configuration change judgment on an
non-existent and non new link.
[Fix]
Quickly exit when there is a existent link and the link configuration has not
changed.
Fixes: b303835dabe0 ("wifi: mac80211: accept STA changes without link changes")
Reported-and-tested-by: [email protected]
Signed-off-by: Edward Adam Davis <[email protected]>
Link: https://msgid.link/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
|
|
As announced [1][2], I have taken over maintainership of the
wireless-regdb project.
Add my certificate so that newer releases are valid to the kernel.
Seth's certificate should be kept around for awhile, at least until
a few new releases by me happen.
This should also be applied to stable trees so that stable kernels
can utilize newly released database binaries.
[1] https://lore.kernel.org/linux-wireless/CAGb2v657baNMPKU3QADijx7hZa=GUcSv2LEDdn6N=QQaFX8r-g@mail.gmail.com/
[2] https://lore.kernel.org/linux-wireless/[email protected]/
Cc: [email protected]
Signed-off-by: Chen-Yu Tsai <[email protected]>
Acked-by: Seth Forshee <[email protected]>
Link: https://msgid.link/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
|
|
Evidently I had only looked at all the ones in rx.c, and missed this.
Add bh-disable to this use of the rxq->lock as well.
Fixes: 25edc8f259c7 ("iwlwifi: pcie: properly implement NAPI")
Reported-by: Brian Norris <[email protected]>
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Miri Korenblit <[email protected]>
Link: https://msgid.link/20231208183100.e79ad3dae649.I8f19713c4383707f8be7fc20ff5cc1ecf12429bb@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
For vendor action frames, whether a protected one should be
used or not is clearly up to the individual vendor and frame,
so even though a protected dual is defined, it may not get
used. Thus, don't require protection for vendor action frames
when they're used in a connection.
Since we obviously don't process frames unknown to the kernel
in the kernel, it may makes sense to invert this list to have
all the ones the kernel processes and knows to be requiring
protection, but that'd be a different change.
Fixes: 91535613b609 ("wifi: mac80211: don't drop all unprotected public action frames")
Reported-by: Jouni Malinen <[email protected]>
Link: https://msgid.link/20231206223801.f6a2cf4e67ec.Ifa6acc774bd67801d3dafb405278f297683187aa@changeid
Signed-off-by: Johannes Berg <[email protected]>
|
|
Instead of having a comment indicating the need to hold slots_lock
when calling kvm_io_bus_register_dev(), make it explicit with
a lockdep assertion.
Signed-off-by: Marc Zyngier <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Oliver Upton <[email protected]>
|
|
vgic_register_all_redist_iodevs()
Although we implicitly depend on slots_lock being held when registering
IO devices with the IO bus infrastructure, we don't enforce this
requirement. Make it explicit.
Signed-off-by: Marc Zyngier <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Oliver Upton <[email protected]>
|
|
When failing to create a vcpu because (for example) it has a
duplicate vcpu_id, we destroy the vcpu. Amusingly, this leaves
the redistributor registered with the KVM_MMIO bus.
This is no good, and we should properly clean the mess. Force
a teardown of the vgic vcpu interface, including the RD device
before returning to the caller.
Cc: [email protected]
Signed-off-by: Marc Zyngier <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Oliver Upton <[email protected]>
|
|
As we are going to need to call into kvm_vgic_vcpu_destroy() without
prior holding of the slots_lock, introduce __kvm_vgic_vcpu_destroy()
as a non-locking primitive of kvm_vgic_vcpu_destroy().
Cc: [email protected]
Signed-off-by: Marc Zyngier <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Oliver Upton <[email protected]>
|
|
When destroying a vgic, we have rather cumbersome rules about
when slots_lock and config_lock are held, resulting in fun
buglets.
The first port of call is to simplify kvm_vgic_map_resources()
so that there is only one call to kvm_vgic_destroy() instead of
two, with the second only holding half of the locks.
For that, we kill the non-locking primitive and move the call
outside of the locking altogether. This doesn't change anything
(we re-acquire the locks and teardown the whole vgic), and
simplifies the code significantly.
Cc: [email protected]
Signed-off-by: Marc Zyngier <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Oliver Upton <[email protected]>
|
|
On trylock failure we were waiting for outstanding reads to complete -
but nocow locks need to be held until the whole move is finished.
Signed-off-by: Kent Overstreet <[email protected]>
|
|
Pull more bcachefs bugfixes from Kent Overstreet:
- Fix a rare emergency shutdown path bug: dropping journal pins after
the filesystem has mostly been torn down is not what we want.
- Fix some concurrency issues with the btree write buffer and journal
replay by not using the btree write buffer until journal replay is
finished
- A fixup from the prior patch to kill journal pre-reservations: at the
start of the btree update path, where previously we took a
pre-reservation, we do at least want to check the journal watermark.
- Fix a race between dropping device metadata and btree node writes,
which would re-add a pointer to a device that had just been dropped
- Fix one of the SCRU lock warnings, in
bch2_compression_stats_to_text().
- Partial fix for a rare transaction paths overflow, when indirect
extents had been split by background tasks, by not running certain
triggers when they're not needed.
- Fix for creating a snapshot with implicit source in a subdirectory of
the containing subvolume
- Don't unfreeze when we're emergency read-only
- Fix for rebalance spinning trying to compress unwritten extentns
- Another deleted_inodes fix, for directories
- Fix a rare deadlock (usually just an unecessary wait) when flushing
the journal with an open journal entry.
* tag 'bcachefs-2023-12-10' of https://evilpiepirate.org/git/bcachefs:
bcachefs: Close journal entry if necessary when flushing all pins
bcachefs: Fix uninitialized var in bch2_journal_replay()
bcachefs: Fix deleted inode check for dirs
bcachefs: rebalance shouldn't attempt to compress unwritten extents
bcachefs: don't attempt rw on unfreeze when shutdown
bcachefs: Fix creating snapshot with implict source
bcachefs: Don't run indirect extent trigger unless inserting/deleting
bcachefs: Convert compression_stats to for_each_btree_key2
bcachefs: Fix bch2_extent_drop_ptrs() call
bcachefs: Fix a journal deadlock in replay
bcachefs; Don't use btree write buffer until journal replay is finished
bcachefs: Don't drop journal pins in exit path
|
|
If an AFS cell that has an unreachable (eg. ENETUNREACH) server listed (VL
server or fileserver), an asynchronous probe to one of its addresses may
fail immediately because sendmsg() returns an error. When this happens, a
refcount underflow can happen if certain events hit a very small window.
The way this occurs is:
(1) There are two levels of "call" object, the afs_call and the
rxrpc_call. Each of them can be transitioned to a "completed" state
in the event of success or failure.
(2) Asynchronous afs_calls are self-referential whilst they are active to
prevent them from evaporating when they're not being processed. This
reference is disposed of when the afs_call is completed.
Note that an afs_call may only be completed once; once completed
completing it again will do nothing.
(3) When a call transmission is made, the app-side rxrpc code queues a Tx
buffer for the rxrpc I/O thread to transmit. The I/O thread invokes
sendmsg() to transmit it - and in the case of failure, it transitions
the rxrpc_call to the completed state.
(4) When an rxrpc_call is completed, the app layer is notified. In this
case, the app is kafs and it schedules a work item to process events
pertaining to an afs_call.
(5) When the afs_call event processor is run, it goes down through the
RPC-specific handler to afs_extract_data() to retrieve data from rxrpc
- and, in this case, it picks up the error from the rxrpc_call and
returns it.
The error is then propagated to the afs_call and that is completed
too. At this point the self-reference is released.
(6) If the rxrpc I/O thread manages to complete the rxrpc_call within the
window between rxrpc_send_data() queuing the request packet and
checking for call completion on the way out, then
rxrpc_kernel_send_data() will return the error from sendmsg() to the
app.
(7) Then afs_make_call() will see an error and will jump to the error
handling path which will attempt to clean up the afs_call.
(8) The problem comes when the error handling path in afs_make_call()
tries to unconditionally drop an async afs_call's self-reference.
This self-reference, however, may already have been dropped by
afs_extract_data() completing the afs_call
(9) The refcount underflows when we return to afs_do_probe_vlserver() and
that tries to drop its reference on the afs_call.
Fix this by making afs_make_call() attempt to complete the afs_call rather
than unconditionally putting it. That way, if afs_extract_data() manages
to complete the call first, afs_make_call() won't do anything.
The bug can be forced by making do_udp_sendmsg() return -ENETUNREACH and
sticking an msleep() in rxrpc_send_data() after the 'success:' label to
widen the race window.
The error message looks something like:
refcount_t: underflow; use-after-free.
WARNING: CPU: 3 PID: 720 at lib/refcount.c:28 refcount_warn_saturate+0xba/0x110
...
RIP: 0010:refcount_warn_saturate+0xba/0x110
...
afs_put_call+0x1dc/0x1f0 [kafs]
afs_fs_get_capabilities+0x8b/0xe0 [kafs]
afs_fs_probe_fileserver+0x188/0x1e0 [kafs]
afs_lookup_server+0x3bf/0x3f0 [kafs]
afs_alloc_server_list+0x130/0x2e0 [kafs]
afs_create_volume+0x162/0x400 [kafs]
afs_get_tree+0x266/0x410 [kafs]
vfs_get_tree+0x25/0xc0
fc_mount+0xe/0x40
afs_d_automount+0x1b3/0x390 [kafs]
__traverse_mounts+0x8f/0x210
step_into+0x340/0x760
path_openat+0x13a/0x1260
do_filp_open+0xaf/0x160
do_sys_openat2+0xaf/0x170
or something like:
refcount_t: underflow; use-after-free.
...
RIP: 0010:refcount_warn_saturate+0x99/0xda
...
afs_put_call+0x4a/0x175
afs_send_vl_probes+0x108/0x172
afs_select_vlserver+0xd6/0x311
afs_do_cell_detect_alias+0x5e/0x1e9
afs_cell_detect_alias+0x44/0x92
afs_validate_fc+0x9d/0x134
afs_get_tree+0x20/0x2e6
vfs_get_tree+0x1d/0xc9
fc_mount+0xe/0x33
afs_d_automount+0x48/0x9d
__traverse_mounts+0xe0/0x166
step_into+0x140/0x274
open_last_lookups+0x1c1/0x1df
path_openat+0x138/0x1c3
do_filp_open+0x55/0xb4
do_sys_openat2+0x6c/0xb6
Fixes: 34fa47612bfe ("afs: Fix race in async call refcounting")
Reported-by: Bill MacAllister <[email protected]>
Closes: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1052304
Suggested-by: Jeffrey E Altman <[email protected]>
Signed-off-by: David Howells <[email protected]>
Reviewed-by: Jeffrey Altman <[email protected]>
cc: Marc Dionne <[email protected]>
cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]/ # v1
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Validate @ioctl_rsp->OutputOffset and @ioctl_rsp->OutputCount so that
their sum does not wrap to a number that is smaller than @reparse_buf
and we end up with a wild pointer as follows:
BUG: unable to handle page fault for address: ffff88809c5cd45f
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 4a01067 P4D 4a01067 PUD 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 2 PID: 1260 Comm: mount.cifs Not tainted 6.7.0-rc4 #2
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.16.2-3-gd478f380-rebuilt.opensuse.org 04/01/2014
RIP: 0010:smb2_query_reparse_point+0x3e0/0x4c0 [cifs]
Code: ff ff e8 f3 51 fe ff 41 89 c6 58 5a 45 85 f6 0f 85 14 fe ff ff
49 8b 57 48 8b 42 60 44 8b 42 64 42 8d 0c 00 49 39 4f 50 72 40 <8b>
04 02 48 8b 9d f0 fe ff ff 49 8b 57 50 89 03 48 8b 9d e8 fe ff
RSP: 0018:ffffc90000347a90 EFLAGS: 00010212
RAX: 000000008000001f RBX: ffff88800ae11000 RCX: 00000000000000ec
RDX: ffff88801c5cd440 RSI: 0000000000000000 RDI: ffffffff82004aa4
RBP: ffffc90000347bb0 R08: 00000000800000cd R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000024 R12: ffff8880114d4100
R13: ffff8880114d4198 R14: 0000000000000000 R15: ffff8880114d4000
FS: 00007f02c07babc0(0000) GS:ffff88806ba00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff88809c5cd45f CR3: 0000000011750000 CR4: 0000000000750ef0
PKRU: 55555554
Call Trace:
<TASK>
? __die+0x23/0x70
? page_fault_oops+0x181/0x480
? search_module_extables+0x19/0x60
? srso_alias_return_thunk+0x5/0xfbef5
? exc_page_fault+0x1b6/0x1c0
? asm_exc_page_fault+0x26/0x30
? _raw_spin_unlock_irqrestore+0x44/0x60
? smb2_query_reparse_point+0x3e0/0x4c0 [cifs]
cifs_get_fattr+0x16e/0xa50 [cifs]
? srso_alias_return_thunk+0x5/0xfbef5
? lock_acquire+0xbf/0x2b0
cifs_root_iget+0x163/0x5f0 [cifs]
cifs_smb3_do_mount+0x5bd/0x780 [cifs]
smb3_get_tree+0xd9/0x290 [cifs]
vfs_get_tree+0x2c/0x100
? capable+0x37/0x70
path_mount+0x2d7/0xb80
? srso_alias_return_thunk+0x5/0xfbef5
? _raw_spin_unlock_irqrestore+0x44/0x60
__x64_sys_mount+0x11a/0x150
do_syscall_64+0x47/0xf0
entry_SYSCALL_64_after_hwframe+0x6f/0x77
RIP: 0033:0x7f02c08d5b1e
Fixes: 2e4564b31b64 ("smb3: add support for stat of WSL reparse points for special file types")
Cc: [email protected]
Reported-by: Robert Morris <[email protected]>
Signed-off-by: Paulo Alcantara (SUSE) <[email protected]>
Signed-off-by: Steve French <[email protected]>
|