| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Correct mismatch between the name of flow_offload_has_one_action()
and its kdoc entry.
Found using ./scripts/kernel-doc -Werror -none include/net/flow_offload.h
Signed-off-by: Bijie Xu <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
It turned out that the current implementation of the port subscription
is racy. The subscription contains two linked lists, and we have to
add to or delete from both lists. Since both connection and
disconnection procedures perform the same order for those two lists
(i.e. src list, then dest list), when a deletion happens during a
connection procedure, the src list may be deleted before the dest list
addition completes, and this may lead to a use-after-free or an Oops,
even though the access to both lists are protected via mutex.
The simple workaround for this race is to change the access order for
the disconnection, namely, dest list, then src list. This assures
that the connection has been established when disconnecting, and also
the concurrent deletion can be avoided.
Reported-and-tested-by: folkert <[email protected]>
Cc: <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
In the unlikely event that pci_register_device() fails, we were tearing
down our PMU setup but not globals. This leaves a bunch of memory slabs
lying around.
Signed-off-by: Jason Ekstrand <[email protected]>
Fixes: 32eb6bcfdda9 ("drm/i915: Make request allocation caches global")
[danvet: Fix conflicts against removal of the globals_flush
infrastructure.]
Reviewed-by: Daniel Vetter <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit db484889d1ff0645e07e360d3e3ad306c0515821)
Signed-off-by: Rodrigo Vivi <[email protected]>
[Fixed small conflict while cherry picking]
|
|
The register offset for SFC_DONE was missing a '0' at the end, causing
us to read from a non-existent register address. We only use this
register in error state dumps so the mistake hasn't caused any real
problems, but fixing it will hopefully make the error state dumps a bit
more useful for debugging.
Fixes: e50dbdbfd9fb ("drm/i915/tgl: Add SFC instdone to error state")
Cc: Mika Kuoppala <[email protected]>
Signed-off-by: Matt Roper <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Reviewed-by: Mika Kuoppala <[email protected]>
(cherry picked from commit 82929a2140eb99f1f1d21855f3f580e70d7abdd8)
Signed-off-by: Rodrigo Vivi <[email protected]>
|
|
I saw the build failure that was fixed in commit 6387f65e2acb ("net:
sparx5: fix compiletime_assert for GCC 4.9") and noticed another
issue that was introduced in the same patch: Using GENMASK() to
create a 64-bit mask does not work on 32-bit architectures.
This probably won't ever happen on this driver since it's specific
to a 64-bit SoC, but it's better to write it portably, so use
GENMASK_ULL() instead.
Fixes: f3cad2611a77 ("net: sparx5: add hostmode with phylink support")
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In commit 58acd1009226 ("sctp: update active_key for asoc when old key is
being replaced"), sctp_auth_asoc_init_active_key() is called to update
the active_key right after the old key is deleted and before the new key
is added, and it caused that the active_key could be found with the key_id.
In Ying Xu's testing, the BUG_ON in sctp_auth_asoc_init_active_key() was
triggered:
[ ] kernel BUG at net/sctp/auth.c:416!
[ ] RIP: 0010:sctp_auth_asoc_init_active_key.part.8+0xe7/0xf0 [sctp]
[ ] Call Trace:
[ ] sctp_auth_set_key+0x16d/0x1b0 [sctp]
[ ] sctp_setsockopt.part.33+0x1ba9/0x2bd0 [sctp]
[ ] __sys_setsockopt+0xd6/0x1d0
[ ] __x64_sys_setsockopt+0x20/0x30
[ ] do_syscall_64+0x5b/0x1a0
So fix it by moving the active_key update after sh_keys is added.
Fixes: 58acd1009226 ("sctp: update active_key for asoc when old key is being replaced")
Reported-by: Ying Xu <[email protected]>
Signed-off-by: Xin Long <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Check that #UD is raised if bit 16 is clear in
HYPERV_CPUID_FEATURES.EDX and an 'XMM fast' hypercall is issued.
Signed-off-by: Vitaly Kuznetsov <[email protected]>
Reviewed-by: Siddharth Chandrasekaran <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
hypercall input
TLFS states that "Availability of the XMM fast hypercall interface is
indicated via the “Hypervisor Feature Identification” CPUID Leaf
(0x40000003, see section 2.4.4) ... Any attempt to use this interface
when the hypervisor does not indicate availability will result in a #UD
fault."
Implement the check for 'strict' mode (KVM_CAP_HYPERV_ENFORCE_CPUID).
Signed-off-by: Vitaly Kuznetsov <[email protected]>
Reviewed-by: Siddharth Chandrasekaran <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
Hypercall failures are unusual with potentially far going consequences
so it would be useful to see their results when tracing.
Signed-off-by: Vitaly Kuznetsov <[email protected]>
Reviewed-by: Siddharth Chandrasekaran <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
In case guest doesn't have access to the particular hypercall we can avoid
reading XMM registers.
Signed-off-by: Vitaly Kuznetsov <[email protected]>
Reviewed-by: Siddharth Chandrasekaran <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
Signed-off-by: David S. Miller <[email protected]>
|
|
When the function_graph tracer is in use, arch_stack_walk() may unwind
the stack incorrectly, erroneously reporting itself, missing the final
entry which is being traced, and reporting all traced entries between
these off-by-one from where they should be.
When ftrace hooks a function return, the original return address is
saved to the fgraph ret_stack, and the return address in the LR (or the
function's frame record) is replaced with `return_to_handler`.
When arm64's unwinder encounter frames returning to `return_to_handler`,
it finds the associated original return address from the fgraph ret
stack, assuming the most recent `ret_to_hander` entry on the stack
corresponds to the most recent entry in the fgraph ret stack, and so on.
When arch_stack_walk() is used to dump the current task's stack, it
starts from the caller of arch_stack_walk(). However, arch_stack_walk()
can be traced, and so may push an entry on to the fgraph ret stack,
leaving the fgraph ret stack offset by one from the expected position.
This can be seen when dumping the stack via /proc/self/stack, where
enabling the graph tracer results in an unexpected
`stack_trace_save_tsk` entry at the start of the trace, and `el0_svc`
missing form the end of the trace.
This patch fixes this by marking arch_stack_walk() as notrace, as we do
for all other functions on the path to ftrace_graph_get_ret_stack().
While a few helper functions are not marked notrace, their calls/returns
are balanced, and will have no observable effect when examining the
fgraph ret stack.
It is possible for an exeption boundary to cause a similar offset if the
return address of the interrupted context was in the LR. Fixing those
cases will require some more substantial rework, and is left for
subsequent patches.
Before:
| # cat /proc/self/stack
| [<0>] proc_pid_stack+0xc4/0x140
| [<0>] proc_single_show+0x6c/0x120
| [<0>] seq_read_iter+0x240/0x4e0
| [<0>] seq_read+0xe8/0x140
| [<0>] vfs_read+0xb8/0x1e4
| [<0>] ksys_read+0x74/0x100
| [<0>] __arm64_sys_read+0x28/0x3c
| [<0>] invoke_syscall+0x50/0x120
| [<0>] el0_svc_common.constprop.0+0xc4/0xd4
| [<0>] do_el0_svc+0x30/0x9c
| [<0>] el0_svc+0x2c/0x54
| [<0>] el0t_64_sync_handler+0x1a8/0x1b0
| [<0>] el0t_64_sync+0x198/0x19c
| # echo function_graph > /sys/kernel/tracing/current_tracer
| # cat /proc/self/stack
| [<0>] stack_trace_save_tsk+0xa4/0x110
| [<0>] proc_pid_stack+0xc4/0x140
| [<0>] proc_single_show+0x6c/0x120
| [<0>] seq_read_iter+0x240/0x4e0
| [<0>] seq_read+0xe8/0x140
| [<0>] vfs_read+0xb8/0x1e4
| [<0>] ksys_read+0x74/0x100
| [<0>] __arm64_sys_read+0x28/0x3c
| [<0>] invoke_syscall+0x50/0x120
| [<0>] el0_svc_common.constprop.0+0xc4/0xd4
| [<0>] do_el0_svc+0x30/0x9c
| [<0>] el0t_64_sync_handler+0x1a8/0x1b0
| [<0>] el0t_64_sync+0x198/0x19c
After:
| # cat /proc/self/stack
| [<0>] proc_pid_stack+0xc4/0x140
| [<0>] proc_single_show+0x6c/0x120
| [<0>] seq_read_iter+0x240/0x4e0
| [<0>] seq_read+0xe8/0x140
| [<0>] vfs_read+0xb8/0x1e4
| [<0>] ksys_read+0x74/0x100
| [<0>] __arm64_sys_read+0x28/0x3c
| [<0>] invoke_syscall+0x50/0x120
| [<0>] el0_svc_common.constprop.0+0xc4/0xd4
| [<0>] do_el0_svc+0x30/0x9c
| [<0>] el0_svc+0x2c/0x54
| [<0>] el0t_64_sync_handler+0x1a8/0x1b0
| [<0>] el0t_64_sync+0x198/0x19c
| # echo function_graph > /sys/kernel/tracing/current_tracer
| # cat /proc/self/stack
| [<0>] proc_pid_stack+0xc4/0x140
| [<0>] proc_single_show+0x6c/0x120
| [<0>] seq_read_iter+0x240/0x4e0
| [<0>] seq_read+0xe8/0x140
| [<0>] vfs_read+0xb8/0x1e4
| [<0>] ksys_read+0x74/0x100
| [<0>] __arm64_sys_read+0x28/0x3c
| [<0>] invoke_syscall+0x50/0x120
| [<0>] el0_svc_common.constprop.0+0xc4/0xd4
| [<0>] do_el0_svc+0x30/0x9c
| [<0>] el0_svc+0x2c/0x54
| [<0>] el0t_64_sync_handler+0x1a8/0x1b0
| [<0>] el0t_64_sync+0x198/0x19c
Cc: <[email protected]>
Signed-off-by: Mark Rutland <[email protected]>
Cc: Catalin Marinas <[email protected]>
Cc: Madhavan T. Venkataraman <[email protected]>
Cc: Mark Brown <[email protected]>
Cc: Will Deacon <[email protected]>
Reviwed-by: Mark Brown <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
Due to a copy-paste error, we describe struct stackframe::pc as a
snapshot of the `fp` field rather than the `lr` field.
Fix the comment.
Signed-off-by: Mark Rutland <[email protected]>
Cc: Catalin Marinas <[email protected]>
Cc: Madhavan T. Venkataraman <[email protected]>
Cc: Mark Brown <[email protected]>
Cc: Will Deacon <[email protected]>
Reviewed-by: Mark Brown <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
Obviously kaslr is setting the module region to 2GB rather than 4GB since
commit b2eed9b588112 ("arm64/kernel: kaslr: reduce module randomization
range to 2 GB"). So fix the size of region in Kconfig.
On the other hand, even though RANDOMIZE_MODULE_REGION_FULL is not set,
module_alloc() can fall back to a 2GB window if ARM64_MODULE_PLTS is set.
In this case, veneers are still needed. !RANDOMIZE_MODULE_REGION_FULL
doesn't necessarily mean veneers are not needed.
So fix the doc to be more precise to avoid any confusion to the readers
of the code.
Cc: Masami Hiramatsu <[email protected]>
Cc: Ard Biesheuvel <[email protected]>
Cc: Qi Liu <[email protected]>
Signed-off-by: Barry Song <[email protected]>
Reviewed-by: Masami Hiramatsu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
Commit 987fdfec2410 ("arm64: move --fix-cortex-a53-843419 linker test to
Kconfig") fixed the false-positive warning in the installation step.
Yet, there are some cases where this false-positive is shown. For example,
you can see it when you cross 987fdfec2410 during git-bisect.
$ git checkout 987fdfec2410^
[ snip ]
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- defconfig all
[ snip ]
$ git checkout v5.13
[ snip]
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- defconfig all
[ snip ]
arch/arm64/Makefile:25: ld does not support --fix-cortex-a53-843419; kernel may be susceptible to erratum
In the stale include/config/auto.config, CONFIG_ARM64_ERRATUM_843419=y
is set without CONFIG_ARM64_LD_HAS_FIX_ERRATUM_843419, so the warning
is displayed while parsing the Makefiles.
Make will restart with the updated include/config/auto.config, hence
CONFIG_ARM64_LD_HAS_FIX_ERRATUM_843419 will be set eventually, but
this warning is a surprise for users.
Commit 25896d073d8a ("x86/build: Fix compiler support check for
CONFIG_RETPOLINE") addressed a similar issue.
Move $(warning ...) out of the parse stage of Makefiles.
The same applies to CONFIG_ARM64_USE_LSE_ATOMICS.
Signed-off-by: Masahiro Yamada <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
Due to inconsistencies in the way we manipulate compat GPRs, we have a
few issues today:
* For audit and tracing, where error codes are handled as a (native)
long, negative error codes are expected to be sign-extended to the
native 64-bits, or they may fail to be matched correctly. Thus a
syscall which fails with an error may erroneously be identified as
failing.
* For ptrace, *all* compat return values should be sign-extended for
consistency with 32-bit arm, but we currently only do this for
negative return codes.
* As we may transiently set the upper 32 bits of some compat GPRs while
in the kernel, these can be sampled by perf, which is somewhat
confusing. This means that where a syscall returns a pointer above 2G,
this will be sign-extended, but will not be mistaken for an error as
error codes are constrained to the inclusive range [-4096, -1] where
no user pointer can exist.
To fix all of these, we must consistently use helpers to get/set the
compat GPRs, ensuring that we never write the upper 32 bits of the
return code, and always sign-extend when reading the return code. This
patch does so, with the following changes:
* We re-organise syscall_get_return_value() to always sign-extend for
compat tasks, and reimplement syscall_get_error() atop. We update
syscall_trace_exit() to use syscall_get_return_value().
* We consistently use syscall_set_return_value() to set the return
value, ensureing the upper 32 bits are never set unexpectedly.
* As the core audit code currently uses regs_return_value() rather than
syscall_get_return_value(), we special-case this for
compat_user_mode(regs) such that this will do the right thing. Going
forward, we should try to move the core audit code over to
syscall_get_return_value().
Cc: <[email protected]>
Reported-by: He Zhe <[email protected]>
Reported-by: weiyuchen <[email protected]>
Cc: Catalin Marinas <[email protected]>
Cc: Will Deacon <[email protected]>
Reviewed-by: Catalin Marinas <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
Sparse reports a compile time warning when dereferencing an
__iomem pointer:
drivers/soc/ixp4xx/ixp4xx-qmgr.c:149:37: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:153:40: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:154:40: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:174:38: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:174:44: warning: dereference of noderef expression
Use __raw_readl() here for consistency with the rest of the file.
This should really get converted to some proper accessor, as the
__raw functions are not meant to be used in drivers, but the driver
has used these since the start, so for the moment, let's only fix
the warning.
Reported-by: kernel test robot <[email protected]>
Fixes: d4c9e9fc9751 ("IXP42x: Add QMgr support for IXP425 rev. A0 processors.")
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
When compile-testing with 64-bit resource_size_t, gcc reports an invalid
printk format string:
In file included from include/linux/dma-mapping.h:7,
from drivers/soc/ixp4xx/ixp4xx-npe.c:15:
drivers/soc/ixp4xx/ixp4xx-npe.c: In function 'ixp4xx_npe_probe':
drivers/soc/ixp4xx/ixp4xx-npe.c:694:18: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
dev_info(dev, "NPE%d at 0x%08x-0x%08x not available\n",
Use the special %pR format string to print the resources.
Fixes: 0b458d7b10f8 ("soc: ixp4xx: npe: Pass addresses as resources")
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
entry
Currently it is possible to add broken extern_learn FDB entries to the
bridge in two ways:
1. Entries pointing towards the bridge device that are not local/permanent:
ip link add br0 type bridge
bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn static
2. Entries pointing towards the bridge device or towards a port that
are marked as local/permanent, however the bridge does not process the
'permanent' bit in any way, therefore they are recorded as though they
aren't permanent:
ip link add br0 type bridge
bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn permanent
Since commit 52e4bec15546 ("net: bridge: switchdev: treat local FDBs the
same as entries towards the bridge"), these incorrect FDB entries can
even trigger NULL pointer dereferences inside the kernel.
This is because that commit made the assumption that all FDB entries
that are not local/permanent have a valid destination port. For context,
local / permanent FDB entries either have fdb->dst == NULL, and these
point towards the bridge device and are therefore local and not to be
used for forwarding, or have fdb->dst == a net_bridge_port structure
(but are to be treated in the same way, i.e. not for forwarding).
That assumption _is_ correct as long as things are working correctly in
the bridge driver, i.e. we cannot logically have fdb->dst == NULL under
any circumstance for FDB entries that are not local. However, the
extern_learn code path where FDB entries are managed by a user space
controller show that it is possible for the bridge kernel driver to
misinterpret the NUD flags of an entry transmitted by user space, and
end up having fdb->dst == NULL while not being a local entry. This is
invalid and should be rejected.
Before, the two commands listed above both crashed the kernel in this
check from br_switchdev_fdb_notify:
struct net_device *dev = info.is_local ? br->dev : dst->dev;
info.is_local == false, dst == NULL.
After this patch, the invalid entry added by the first command is
rejected:
ip link add br0 type bridge && bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn static; ip link del br0
Error: bridge: FDB entry towards bridge must be permanent.
and the valid entry added by the second command is properly treated as a
local address and does not crash br_switchdev_fdb_notify anymore:
ip link add br0 type bridge && bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn permanent; ip link del br0
Fixes: eb100e0e24a2 ("net: bridge: allow to add externally learned entries from user-space")
Reported-by: [email protected]
Signed-off-by: Vladimir Oltean <[email protected]>
Acked-by: Nikolay Aleksandrov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Register accesses are always 4bytes, accidently this was changed to
a void pointer whwqich badly breaks 64bit archs when running on top
of svga3.
Fixes: 2cd80dbd3551 ("drm/vmwgfx: Add basic support for SVGA3")
Signed-off-by: Zack Rusin <[email protected]>
Reviewed-by: Martin Krastev <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 87360168759879d68550b0c052bbcc2a0339ff74)
Signed-off-by: Thomas Zimmermann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga into char-misc-linus
Moritz writes:
FPGA Manager fix for 5.14
Kajol's fix adds a missing pmu_migrate_context() call which presents a
problem if the CPU collecting FME PMU data is taken offline.
All patches have been reviewed on the mailing list, and have been in the
last few linux-next releases (as part of my fixes branch) without issues.
Signed-off-by: Moritz Fischer <[email protected]>
* tag 'fpga-fixes-for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga:
fpga: dfl: fme: Fix cpu hotplug issue in performance reporting
|
|
An earlier patch removed setting of tot_len in IPv4 headers because it was
also set in ip_local_out. However, this change resulted in an incorrect
ICRC being computed because the tot_len field is not masked out. This
patch restores that line. This fixes the bug reported by Zhu Yanjun. This
bug affects anyone using rxe which is currently broken.
Fixes: 230bb836ee88 ("RDMA/rxe: Fix redundant call to ip_send_check")
Link: https://lore.kernel.org/r/[email protected]
Reported-by: Zhu Yanjun <[email protected]>
Signed-off-by: Bob Pearson <[email protected]>
Reviewed-and-tested-by: Zhu Yanjun <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
The memcpy() that copies a WQE from a SRQ the QP uses an incorrect size.
The size should have been the size of the rxe_send_wqe struct not the size
of a pointer to it. The result is that IO operations using a SRQ on the
responder side will fail.
Fixes: ec0fa2445c18 ("RDMA/rxe: Fix over copying in get_srq_wqe")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bob Pearson <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
The net/sunrpc/xprtrdma module creates its QP using rdma_create_qp() and
immediately post receives, implicitly assuming the QP is in the INIT state
and thus valid for ib_post_recv().
The patch noted in Fixes: removed the RESET->INIT modifiy from
rdma_create_qp(), breaking NFS rdma for verbs providers that fail the
ib_post_recv() for a bad state.
This situation was proven using kprobes in rvt_post_recv() and
rvt_modify_qp(). The traces showed that the rvt_post_recv() failed before
ANY modify QP and that the current state was RESET.
Fix by reverting the patch below.
Fixes: dc70f7c3ed34 ("RDMA/cma: Remove unnecessary INIT->INIT transition")
Link: https://lore.kernel.org/r/1627583182-81330-1-git-send-email-mike.marciniszyn@cornelisnetworks.com
Cc: Haakon Bugge <[email protected]>
Cc: Chuck Lever III <[email protected]>
Signed-off-by: Mike Marciniszyn <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
Fixing a typo that causes a cache entry to shrink immediately after adding
to it new MRs if the entry size exceeds the high limit. In doing so, the
cache misses its purpose to prevent the creation of new mkeys on the
runtime by using the cached ones.
Fixes: b9358bdbc713 ("RDMA/mlx5: Fix locking in MR cache work queue")
Link: https://lore.kernel.org/r/fcb546986be346684a016f5ca23a0567399145fa.1627370131.git.leonro@nvidia.com
Signed-off-by: Aharon Landau <[email protected]>
Reviewed-by: Maor Gottlieb <[email protected]>
Signed-off-by: Leon Romanovsky <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
|
|
The tqmx86 MFD driver was passing IRQ 0 for "no IRQ" in the past. This
causes warnings with newer kernels.
Prepare the gpio-tqmx86 driver for the fixed MFD driver by handling a
missing IRQ properly.
Fixes: b868db94a6a7 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Matthias Schiffer <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Acked-by: Linus Walleij <[email protected]>
Signed-off-by: Bartosz Golaszewski <[email protected]>
|
|
This reverts commit 40e159403896f7d55c98f858d0b20fee1d941fa4.
Looks like this commit breaks the build for me.
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
IF_OPER_TESTING is in fact used today.
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
TVL -> TLV
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Stephen reports sparx5 broke GCC 4.9 build.
Move the compiletime_assert() out of the static function.
Compile-tested only, no object code changes.
Reported-by: Stephen Rothwell <[email protected]>
Fixes: f3cad2611a77 ("net: sparx5: add hostmode with phylink support")
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <[email protected]>
Signed-off-by: Wang Hai <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The logic for discerning between KSZ8051 and KSZ87XX PHYs is incorrect
such that the that KSZ87XX switch is not identified correctly.
ksz8051_ksz8795_match_phy_device() uses the parameter ksz_phy_id
to discriminate whether it was called from ksz8051_match_phy_device()
or from ksz8795_match_phy_device() but since PHY_ID_KSZ87XX is the
same value as PHY_ID_KSZ8051, this doesn't work.
Instead use a bool to discriminate the caller.
Without this patch, the KSZ8795 switch port identifies as:
ksz8795-switch spi3.1 ade1 (uninitialized): PHY [dsa-0.1:03] driver [Generic PHY]
With the patch, it identifies correctly:
ksz8795-switch spi3.1 ade1 (uninitialized): PHY [dsa-0.1:03] driver [Micrel KSZ87XX Switch]
Fixes: 8b95599c55ed24b36cf4 ("net: phy: micrel: Discern KSZ8051 and KSZ8795 PHYs")
Signed-off-by: Steve Bennett <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
It should not return 0 when SID 0 is assigned to isids.
This patch fixes it.
Cc: [email protected]
Fixes: e3e0b582c321a ("selinux: remove unused initial SIDs and improve handling")
Signed-off-by: Xiu Jianfeng <[email protected]>
[PM: remove changelog from description]
Signed-off-by: Paul Moore <[email protected]>
|
|
Vladimir Oltean says:
====================
FDB fixes for NXP SJA1105
I have some upcoming patches that make heavy use of statically installed
FDB entries, and when testing them on SJA1105P/Q/R/S and SJA1110, it
became clear that these switches do not behave reliably at all.
- On SJA1110, a static FDB entry cannot be installed at all
- On SJA1105P/Q/R/S, it is very picky about the inner/outer VLAN type
- Dynamically learned entries will make us not install static ones, or
even if we do, they might not take effect
Patch 5/6 has a conflict with net-next (sorry), the commit message of
that patch describes how to deal with it. Thanks.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
On SJA1105P/Q/R/S and SJA1110, the L2 Lookup Table entries contain a
maskable "inner/outer tag" bit which means:
- when set to 1: match single-outer and double tagged frames
- when set to 0: match untagged and single-inner tagged frames
- when masked off: match all frames regardless of the type of tag
This driver does not make any meaningful distinction between inner tags
(matches on TPID) and outer tags (matches on TPID2). In fact, all VLAN
table entries are installed as SJA1110_VLAN_D_TAG, which means that they
match on both inner and outer tags.
So it does not make sense that we install FDB entries with the IOTAG bit
set to 1.
In VLAN-unaware mode, we set both TPID and TPID2 to 0xdadb, so the
switch will see frames as outer-tagged or double-tagged (never inner).
So the FDB entries will match if IOTAG is set to 1.
In VLAN-aware mode, we set TPID to 0x8100 and TPID2 to 0x88a8. So the
switch will see untagged and 802.1Q-tagged packets as inner-tagged, and
802.1ad-tagged packets as outer-tagged. So untagged and 802.1Q-tagged
packets will not match FDB entries if IOTAG is set to 1, but 802.1ad
tagged packets will. Strange.
To fix this, simply mask off the IOTAG bit from FDB entries, and make
them match regardless of whether the VLAN tag is inner or outer.
Fixes: 1da73821343c ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Similar but not quite the same with what was done in commit b11f0a4c0c81
("net: dsa: sja1105: be stateless when installing FDB entries") for
SJA1105E/T, it is desirable to drop the priv->vlan_aware check and
simply go ahead and install FDB entries in the VLAN that was given by
the bridge.
As opposed to SJA1105E/T, in SJA1105P/Q/R/S and SJA1110, the FDB is a
maskable TCAM, and we are installing VLAN-unaware FDB entries with the
VLAN ID masked off. However, such FDB entries might completely obscure
VLAN-aware entries where the VLAN ID is included in the search mask,
because the switch looks up the FDB from left to right and picks the
first entry which results in a masked match. So it depends on whether
the bridge installs first the VLAN-unaware or the VLAN-aware FDB entries.
Anyway, if we had a VLAN-unaware FDB entry towards one set of DESTPORTS
and a VLAN-aware one towards other set of DESTPORTS, the result is that
the packets in VLAN-aware mode will be forwarded towards the DESTPORTS
specified by the VLAN-unaware entry.
To solve this, simply do not use the masked matching ability of the FDB
for VLAN ID, and always match precisely on it. In VLAN-unaware mode, we
configure the switch for shared VLAN learning, so the VLAN ID will be
ignored anyway during lookup, so it is redundant to mask it off in the
TCAM.
This patch conflicts with net-next commit 0fac6aa098ed ("net: dsa: sja1105:
delete the best_effort_vlan_filtering mode") which changed this line:
if (priv->vlan_state != SJA1105_VLAN_UNAWARE) {
into:
if (priv->vlan_aware) {
When merging with net-next, the lines added by this patch should take
precedence in the conflict resolution (i.e. the "if" condition should be
deleted in both cases).
Fixes: 1da73821343c ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
new address
Currently, when sja1105pqrs_fdb_add() is called for a host-joined IPv6
MDB entry such as 33:33:00:00:00:6a, the search for that address will
return the FDB entry for SJA1105_UNKNOWN_MULTICAST, which has a
destination MAC of 01:00:00:00:00:00 and a mask of 01:00:00:00:00:00.
It returns that entry because, well, it matches, in the sense that
unknown multicast is supposed by design to match it...
But the issue is that we then proceed to overwrite this entry with the
one for our precise host-joined multicast address, and the unknown
multicast entry is no longer there - unknown multicast is now flooded to
the same group of ports as broadcast, which does not look up the FDB.
To solve this problem, we should ignore searches that return the unknown
multicast address as the match, and treat them as "no match" which will
result in the entry being installed to hardware.
For this to work properly, we need to put the result of the FDB search
in a temporary variable in order to avoid overwriting the l2_lookup
entry we want to program. The l2_lookup entry returned by the search
might not have the same set of DESTPORTS and not even the same MACADDR
as the entry we're trying to add.
Fixes: 4d9423549501 ("net: dsa: sja1105: offload bridge port flags to device")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
statically added ones
The procedure to add a static FDB entry in sja1105 is concurrent with
dynamic learning performed on all bridge ports and the CPU port.
The switch looks up the FDB from left to right, and also learns
dynamically from left to right, so it is possible that between the
moment when we pick up a free slot to install an FDB entry, another slot
to the left of that one becomes free due to an address ageing out, and
that other slot is then immediately used by the switch to learn
dynamically the same address as we're trying to add statically.
The result is that we succeeded to add our static FDB entry, but it is
being shadowed by a dynamic FDB entry to its left, and the switch will
behave as if our static FDB entry did not exist.
We cannot really prevent this from happening unless we make the entire
process to add a static FDB entry a huge critical section where address
learning is temporarily disabled on _all_ ports, and then re-enabled
according to the configuration done by sja1105_port_set_learning.
However, that is kind of disruptive for the operation of the network.
What we can do alternatively is to simply read back the FDB for dynamic
entries located before our newly added static one, and delete them.
This will guarantee that our static FDB entry is now operational. It
will still not guarantee that there aren't dynamic FDB entries to the
_right_ of that static FDB entry, but at least those entries will age
out by themselves since they aren't hit, and won't bother anyone.
Fixes: 291d1e72b756 ("net: dsa: sja1105: Add support for FDB and MDB management")
Fixes: 1da73821343c ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
.port_fdb_add
The SJA1105 switch family leaves it up to software to decide where
within the FDB to install a static entry, and to concatenate destination
ports for already existing entries (the FDB is also used for multicast
entries), it is not as simple as just saying "please add this entry".
This means we first need to search for an existing FDB entry before
adding a new one. The driver currently manages to fool itself into
thinking that if an FDB entry already exists, there is nothing to be
done. But that FDB entry might be dynamically learned, case in which it
should be replaced with a static entry, but instead it is left alone.
This patch checks the LOCKEDS ("locked/static") bit from found FDB
entries, and lets the code "goto skip_finding_an_index;" if the FDB
entry was not static. So we also need to move the place where we set
LOCKEDS = true, to cover the new case where a dynamic FDB entry existed
but was dynamic.
Fixes: 291d1e72b756 ("net: dsa: sja1105: Add support for FDB and MDB management")
Fixes: 1da73821343c ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The blamed commit made FDB access on SJA1110 functional only as far as
dumping the existing entries goes, but anything having to do with an
entry's index (adding, deleting) is still broken.
There are in fact 2 problems, all caused by improperly inheriting the
code from SJA1105P/Q/R/S:
- An entry size is SJA1110_SIZE_L2_LOOKUP_ENTRY (24) bytes and not
SJA1105PQRS_SIZE_L2_LOOKUP_ENTRY (20) bytes
- The "index" field within an FDB entry is at bits 10:1 for SJA1110 and
not 15:6 as in SJA1105P/Q/R/S
This patch moves the packing function for the cmd->index outside of
sja1105pqrs_common_l2_lookup_cmd_packing() and into the device specific
functions sja1105pqrs_l2_lookup_cmd_packing and
sja1110_l2_lookup_cmd_packing.
Fixes: 74e7feff0e22 ("net: dsa: sja1105: fix dynamic access to L2 Address Lookup table for SJA1110")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/fixes
mvebu fixes for 5.14 (part 1)
- Fix i2c property for armada-3720-turris-mox in order to use SFP
- Add mmc alias on armada-3720-turris-mox to allow rootfs using the
right mmc
* tag 'mvebu-fixes-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: armada-3720-turris-mox: remove mrvl,i2c-fast-mode
arm64: dts: armada-3720-turris-mox: fixed indices for the SDHC controllers
Link: https://lore.kernel.org/r/87k0l7zx4v.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/fixes
STM32 DT fixes for v5.14, round 1
Highlights:
-----------
-Fixes are for DHCOM/DHCOR boards:
- Set HW RTC ad default RTC
- Disable EDPD LAN8710 feature as it is not a stable feature.
- Fix touchscreen IRQ line assignment
* tag 'stm32-dt-for-v5.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Fix touchscreen IRQ line assignment on DHCOM
ARM: dts: stm32: Disable LAN8710 EDPD on DHCOM
ARM: dts: stm32: Prefer HW RTC on DHCOM SoM
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.linaro.org:/people/jens.wiklander/linux-tee into arm/fixes
tee: Improve support for kexec and kdump
This fixes several bugs uncovered while exercising the OP-TEE, ftpm
(firmware TPM), and tee_bnxt_fw (Broadcom BNXT firmware manager) drivers
with kexec and kdump (emergency kexec) based workflows.
* tag 'tee-kexec-fixes-for-v5.14' of git://git.linaro.org:/people/jens.wiklander/linux-tee:
firmware: tee_bnxt: Release TEE shm, session, and context during kexec
tpm_ftpm_tee: Free and unregister TEE shared memory during kexec
tee: Correct inappropriate usage of TEE_SHM_DMA_BUF flag
tee: add tee_shm_alloc_kernel_buf()
optee: Clear stale cache entries during initialization
optee: fix tee out of memory failure seen during kexec reboot
optee: Refuse to load the driver under the kdump kernel
optee: Fix memory leak when failing to register shm pages
Link: https://lore.kernel.org/r/20210726081039.GA2482361@jade
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.14:
- A couple of fixes on MMDC driver to add missing iounmap() and
clk_disable_unprepare(), and a follow-up fix.
- Fix missing-prototypes warning in SRC driver.
- Revert commit 7d981405d0fd ("soc: imx8m: change to use platform
driver"), which breaks i.MX8M system that has CAAM driver enabled.
- One fix on imx53-m53menlo pinctrl configuration.
- Increase the PHY reset duration for imx6qdl-sr-som to fix intermittent
issues where the PHY would be unresponsive every once in a while.
- Add missing flag for in-band signalling between PHY and MAC on
kontron-sl28-var2 board to fix network support.
- Limit the SDIO Clock on Colibri iMX6ULL to 25MHz for fixing wireless
noise issue.
- Fix sysclk node name for LS1028A so that U-Boot is able to update the
"clock-frequency" property.
* tag 'imx-fixes-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx: Swap M53Menlo pinctrl_power_button/pinctrl_power_out pins
ARM: imx: fix missing 3rd argument in macro imx_mmdc_perf_init
ARM: dts: colibri-imx6ull: limit SDIO clock to 25MHz
arm64: dts: ls1028: sl28: fix networking for variant 2
Revert "soc: imx8m: change to use platform driver"
ARM: dts: imx6qdl-sr-som: Increase the PHY reset duration to 10ms
ARM: imx: common: Move prototype outside the SMP block
ARM: imx: add missing clk_disable_unprepare()
ARM: imx: add missing iounmap()
arm64: dts: ls1028a: fix node name for the sysclk
Link: https://lore.kernel.org/r/20210726023221.GF5901@dragon
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
When this driver is disabled, the board file fails to build,
so add a dependency:
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'gmlr_pci_preinit':
arch/arm/mach-ixp4xx/goramo_mlr.c:472:9: error: implicit declaration of function 'ixp4xx_pci_preinit'; did you mean 'iop3xx_pci_preinit'? [-Werror=implicit-function-declaration]
472 | ixp4xx_pci_preinit();
| ^~~~~~~~~~~~~~~~~~
| iop3xx_pci_preinit
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'gmlr_pci_postinit':
arch/arm/mach-ixp4xx/goramo_mlr.c:481:22: error: implicit declaration of function 'ixp4xx_pci_read' [-Werror=implicit-function-declaration]
481 | if (!ixp4xx_pci_read(addr, NP_CMD_CONFIGREAD, &value)) {
| ^~~~~~~~~~~~~~~
arch/arm/mach-ixp4xx/goramo_mlr.c:231:35: error: 'IXP4XX_UART1_BASE_PHYS' undeclared here (not in a function)
231 | .start = IXP4XX_UART1_BASE_PHYS,
| ^~~~~~~~~~~~~~~~~~~~~~
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'gmlr_init':
arch/arm/mach-ixp4xx/goramo_mlr.c:376:9: error: implicit declaration of function 'ixp4xx_sys_init' [-Werror=implicit-function-declaration]
376 | ixp4xx_sys_init();
| ^~~~~~~~~~~~~~~
Signed-off-by: Arnd Bergmann <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Cc: Linus Walleij <[email protected]>
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]'
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Randconfig builds on the ixp4xx ethernet driver showed that the qmgr and
npe drivers are not actually built even when compile testing is enabled:
ERROR: modpost: "qmgr_stat_empty" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "qmgr_enable_irq" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "qmgr_set_irq" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "__qmgr_request_queue" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "npe_send_recv_message" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "npe_recv_message" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "npe_load_firmware" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "npe_running" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "qmgr_disable_irq" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "qmgr_stat_below_low_watermark" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
Fix it by always entering the drivers/soc/ixp4xx/ directory, and fix the
resulting compile test failures by removing the #include statements
that prevent building on most other platforms.
Fixes: 7a6c9dbb36a4 ("soc: ixp4xx: Protect IXP4xx SoC drivers by ARCH_IXP4XX || COMPILE_TEST")
Fixes: fcf2d8978cd5 ("ARM: ixp4xx: Move NPE and QMGR to drivers/soc")
Signed-off-by: Arnd Bergmann <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Link: https://lore.kernel.org/r/[email protected]'
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
The regulator coupler drivers now use regulator-driver API function that
isn't available during compile-testing. Make regulator coupler drivers
dependent on CONFIG_REGULATOR in Kconfig.
Fixes: 03978d42ed0d ("soc/tegra: regulators: Bump voltages on system reboot")
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Dmitry Osipenko <[email protected]>
Acked-by: Jon Hunter <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
arm64: tegra: Device tree fixes for v5.14-rc3
This contains one more fix for SMMU enablement on Tegra194, this time
for PCIe.
* tag 'tegra-for-5.14-rc3-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Enable SMMU support for PCIe on Tegra194
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Once the new schema interrupt-controller/arm,vic.yaml is added, we get
the below warnings:
arch/arm/boot/dts/ste-nomadik-nhk15.dt.yaml:
intc@10140000: $nodename:0: 'intc@10140000' does not match
'^interrupt-controller(@[0-9a-f,]+)*$'
Fix the node names for the interrupt controller to conform
to the standard node name interrupt-controller@..
Signed-off-by: Sudeep Holla <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
Cc: Linus Walleij <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Link: https://lore.kernel.org/r/[email protected]'
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Signed-off-by: David S. Miller <[email protected]>
|